V4L/DVB: Add a keymap file with dib0700 table

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: dvb-usb: add support for rc-core mode

Allows dvb-usb drivers to use rc-core, instead of the legacy
implementation.

No driver were ported yet to rc-core, so, some small adjustments
may be needed, when starting to migrate the drivers.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: dvb-usb: prepare drivers for using rc-core

This is a big patch, yet trivial. It just move the RC properties
to a separate struct, in order to prepare the dvb-usb drivers to
use rc-core. There's no change on the behavior of the drivers.

With this change, it is possible to have both legacy and rc-core
based code inside the dvb-usb-remote, allowing a gradual migration
to rc-core, driver per driver.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key

dvb-usb has its own IR handle code. Now that we have a Remote
Controller subsystem, we should start using it. So, remove this
struct, in favor of the similar struct defined at the RC subsystem.

This is a big, but trivial patch. It is a 3 line delect, plus
lots of rename on several dvb-usb files.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: rj54n1cb0c: fix a comment in the driver

RJ54N1CB0C is a Sharp camera sensor.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too

SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution.
This is a bug in the datasheet, VOU also supports the full PAL resolution: 576
lines. Adjust the driver accordingly.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2

Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms

Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor.  This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: V4L2: soc-camera: export soc-camera bus type for notifications

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: V4L2: mediabus: add 12-bit Bayer and YUV420 pixel formats

These formats belong to the standard format set, defined by the MIPI CSI-2
specification.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: mediabus: fix ambiguous pixel code names

Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: CodingStyle cleanups

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: wire up Kconfig and Makefile bits

Make the bits under staging/lirc/ buildable, and add a TODO note.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_zilog driver

Commonly found on several Hauppauge video capture devices.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_ttusbir driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_streamzap driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_sir driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_serial driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_sasem driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_parallel driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_it87 driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_ite8709 driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_imon driver

Nb: this is a very trimmed-down lirc_imon, which only supports the
oldest generation of imon devices that don't do onboard signal decoding
like the most recent generation imon devices -- those are now supported
by the ir-core imon driver.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_igorplugusb driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging: Add an specific TODO note for lirc_i2c

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_i2c driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_ene0100 driver

[mchehab@redhat.com: fixed a few WARNING: please, no space before tabs]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: staging/lirc: add lirc_bt829 driver

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: af9005: use generic_bulk_ctrl_endpoint_response

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Acked-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: dvb: add support for kworld 340u and ub435-q to em28xx-dvb

This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.

The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: DVB: fix dvr node refcounting

In dvb_dvr_release, there is a test dvbdev->users==-1, but users are
never negative. This error results in hung tasks:
  task                        PC stack   pid father
bash          D ffffffffa000c948     0  3264   3170 0x00000000
 ffff88003aec5ce8 0000000000000086 0000000000011f80 0000000000011f80
 ffff88003aec5fd8 ffff88003aec5fd8 ffff88003b848670 0000000000011f80
 ffff88003aec5fd8 0000000000011f80 ffff88003e02a030 ffff88003b848670
Call Trace:
 [<ffffffff813dd4a5>] dvb_dmxdev_release+0xc5/0x130
 [<ffffffff8107b750>] ? autoremove_wake_function+0x0/0x40
 [<ffffffffa00013a2>] dvb_usb_adapter_dvb_exit+0x42/0x70 [dvb_usb]
 [<ffffffffa0000525>] dvb_usb_exit+0x55/0xd0 [dvb_usb]
 [<ffffffffa00005ee>] dvb_usb_device_exit+0x4e/0x70 [dvb_usb]
 [<ffffffffa000a065>] af9015_usb_device_exit+0x55/0x60 [dvb_usb_af9015]
 [<ffffffff813a3f05>] usb_unbind_interface+0x55/0x1a0
 [<ffffffff81316000>] __device_release_driver+0x70/0xe0
...

So check against 1 there instead.

BTW why's the TODO there? Adding TODOs to the code without
descriptions is like adding nothing.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: uvc: Move constants and structures definitions to linux/usb/video.h

The UVC host and gadget drivers both define constants and structures in
private header files. Move all those definitions to linux/usb/video.h
where they can be shared by the two drivers (and be available for
userspace applications).

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: af9013: fix comments

Fix comments. It is demodulator driver not DVB USB -bridge.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: af9013: output fw version as four digit long

Firmware version is four digit long. Print all four digits instead of
three digits used earlier.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: af9013: af9013_read_status() refactoring

Function af9013_read_status() refactoring. Read lock bits in different
order to save count of register reads.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: af9013: program tuner before demodulator

Program tuner before demodulator in case of channel set. Earlier it was
programmed during demodulator programming. This seems to resolve weird
error where demodulator misses sometimes ability to gain lock.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: af9015: support for AverMedia AVerTV Volar M (A815Mac)

Add USB ID 07ca:815a for AverMedia AVerTV Volar M (A815Mac).

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: get_dvb_firmware: update af9015

New driver contains new firmware 5.1.0.0. Fix script to get that.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: af9013: add support for firmware 5.1.0.0

Add support for new firmware version 5.1.0.0.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - vc032x: Move the first VC0321 settings to sd_init()

The first VC0321 settings were done at webcam connection only. They must also
be done on resume after suspend.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - sonixj: Do the audio input work for webcams with a microphone

The bit 0x04 of the bridge register 02 (GPIO) is used for audio connection
in webcams containing the bridge SN9C105. This patch sets it correctly,
according to the presence of an audio device.

Tested-by: Kyle Baker <kyleabaker@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - main: Handle the audio device

When there is an audio device, use a lower alternate setting.
This patch does not fix correctly all audio and bandwidth problems.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - main: Adjust and remove some debug messages

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - main: Remove useless audio ioctl's

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - main: Fix a compilation warning

Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: au0828: move dereference below sanity checks

This function has sanity checks to make sure that "dev" is non-null.  I
moved the dereference down below the checks.  In the current code "dev"
is never actually null.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: media/IR: testing the wrong variable

There is a typo here.  We meant to test "rbuf" instead of "drv".  We
already tested "drv" earlier.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: drivers/video/omap2/displays: add missing mutex_unlock

Add a mutex_unlock missing on the error paths.  The use of the mutex is
balanced elsewhere in the file.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E1;
@@

* mutex_lock(E1,...);
  <+... when != E1
  if (...) {
    ... when != E1
*   return ...;
  }
  ...+>
* mutex_unlock(E1,...);
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: "dib3000mc: reduce large stack usage" fix

s/ENODEV/ENOMEM, per Andreas.

This fix got lost when someone merged "dib3000mc: reduce large stack
usage".  Please don't lose fixes.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: VIDEO: ivtvfb, remove unneeded NULL test

Stanse found that in ivtvfb_callback_cleanup and ivtvfb_callback_init
there are unneeded tests for itv being NULL. But itv is initialized
as container_of with non-zero offset in those functions, so it is
never NULL (even if v4l2_dev is). This was found because itv is
dereferenced earlier than the test.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR/lirc: use memdup_user instead of copy_from_user

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR/lirc: make lirc userspace and staging modules buildable

The lirc userspace needs all the current ioctls defined, and we need to
put the header files in places out-of-tree and/or staging lirc drivers
(which I plan to prep soon) can easily build with. I've actually tested this
in a tree w/all the lirc drivers queued up to be submitted for staging. I'm
also reasonably sure that Andy Walls is going to need most of the ioctls
anyway for his cx23888 IR driver work.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: drivers/media/video: Remove dead CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE

CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE doesn't exist in Kconfig and is never defined anywhere
else, therefore removing all references for it from the source code.

Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: drivers/media: Remove unnecessary casts of private_data

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - sq930x: Add some comments for sensor mt9v111

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - vc032x: Add trace of USB exchanges

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - vc032x: Stop the USB exchanges on error

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - vc032x: Add some comments

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - main: Don't use the frame buffer flags

This patch fixes possible race conditions in queue management with SMP:
when a frame was completed, the irq function tried to use the next frame
buffer. At this time, it was possible that the application on an other
processor updated the frame pointer, making the image to point to a bad
buffer.
The patch contains two main changes:
- the image transfer uses the queue indexes which are protected against
  simultaneous memory access,
- the image pointer which is used for image concatenation is only set at
  interrupt level.
Some subdrivers which used the image pointer have been updated.

Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - main: Possible race condition in queue management

The problem may occur with SMP:
- a frame is completed at interrupt level (in gspca_frame_add with
  packet_type == LAST_PACKET,
- just after clearing the bit V4L2_BUF_FLAG_QUEUED and before setting
  the bit V4L2_BUF_FLAG_DONE, on the other processor, the application
  tries to requeue the same frame buffer,
- then, the qbuf function succeeds because ALL_FLAGS are not set.
The fix sets and resets the two flags in one instruction.

Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: remove obsolete conditionalizing on DVB_DIBCOM_DEBUG

As pointed by Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>,

The config Option DVB_DIBCOM_DEBUG was dropped while removing the dibusb
driver in favor of dvb-usb in 2005. However it remaind existant at some
places of the kernel config.

Instead of just removing the debug capability, the better is to just remove
the bad dependency, making the modprobe function always visible.

Thanks-to: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: lgs8gxx: remove firmware for lgs8g75

The recently added support for lgs8g75 included some 8051 machine code
without accompanying source code.  Replace this with use of the
firmware loader.

Compile-tested only.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB:  si470x: -EINVAL overwritten in si470x_vidioc_s_tuner()

This patch to the si470x_vidioc_s_tuner function was developed in
cooperation with Roel Kluin <roel.kluin@gmail.com>. It sets the default
retval to 0 instead of -EINVAL, identical to what is done in all other
set/get functions of v4l2_ioctl_ops. This is just as cosmetic change, as
retval is directly overwritten by the si470x_disconnect_check() anyway.

Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR/mceusb: more streamlining of device init

Spent a while last night getting device initialization packet captures
under Windows for all generations of devices. There are a few places
where we were doing things differently, and few things we were doing
that we don't need to do, particularly on gen3 hardware, and I *think*
one of those things is what was locking up my pinnacle hw from time to
time -- at least, its been perfectly well behaved every time its been
plugged in since making this change.

First up, we're adding a bit more to the gen1 init routine here. Its
not absolutely necessary, the hardware works the same both with and
without it, but I'd like to be consistent w/Windows here.

Second, DEVICE_RESET is never called when initializing either of my
gen3 devices, its only called for gen1 and gen2. The bits in the gen3
init after removing that, are safe (and interesting) to run on all
hardware, so there's no more gen3-specific init done, there's instead
a generic mceusb_get_parameters() that is run for all hardware.

Third, the gen3 flag isn't needed. We only care if hardware is gen3
during probe, so I've dropped that from the device flags struct.

Successfully tested on all three generations of mceusb hardware.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR/mceusb: remove unused vars from gen1 init

Prior init unification/simplification patch made these unused, forgot
to remove them, so this silences:

drivers/media/IR/mceusb.c: In function ‘mceusb_gen1_init’:
drivers/media/IR/mceusb.c:769: warning: unused variable ‘partial’
drivers/media/IR/mceusb.c:768: warning: unused variable ‘i’

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: lirc: use unlocked_ioctl

New code should not rely on the big kernel lock,
so use the unlocked_ioctl file operation in lirc.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR: jvc-decoder needs BITREVERSE

ir-jvc-decoder uses bitreverse interfaces, so it should select
BITREVERSE.

ir-jvc-decoder.c:(.text+0x550bc): undefined reference to `byte_rev_table'
ir-jvc-decoder.c:(.text+0x550c6): undefined reference to `byte_rev_table'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR/lirc_dev: fix locking in lirc_dev_fop_read

On Wed, Jul 07, 2010 at 02:52:58PM +0200, Jiri Slaby wrote:
> Hi,
>
> stanse found a locking error in lirc_dev_fop_read:
> if (mutex_lock_interruptible(&ir->irctl_lock))
>   return -ERESTARTSYS;
> ...
> while (written < length && ret == 0) {
>   if (mutex_lock_interruptible(&ir->irctl_lock)) {    #1
>     ret = -ERESTARTSYS;
>     break;
>   }
>   ...
> }
>
> remove_wait_queue(&ir->buf->wait_poll, &wait);
> set_current_state(TASK_RUNNING);
> mutex_unlock(&ir->irctl_lock);                        #2
>
> If lock at #1 fails, it beaks out of the loop, with the lock unlocked,
> but there is another "unlock" at #2.

This should do the trick. Completely untested beyond compiling, but its
not exactly a complicated fix, and in practice, I'm not aware of anyone
ever actually tripping that locking bug, so there's zero functional change
in typical use here.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: Retrieve firmware for az6027

Signed-off-by: Renzo Dani <arons7@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: v4l2-dev: fix memory leak

Since commit b4028437876866aba4747a655ede00f892089e14
the 'driver_data' field resides in device's struct device_private
which may be allocated by dev_set_drvdata() if device_private
struct was not allocated previously.

dev_set_drvdata() is used in video_set_drvdata() to set
the driver's private data pointer in v4l2 drivers. Setting
the private data _before_ registering the v4l2 device results
in a memory leak since __video_register_device() also calls
video_set_drvdata(), but after zeroing the device structure.
Thus, the reference to the previously allocated device_private
struct goes lost and a new device_private will be allocated.

All v4l drivers which call video_set_drvdata() _before_
calling video_register_device() are affected. The patch fixes
__video_register_device() to preserve previously allocated
device_private reference.

Caught by kmemleak.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: dvb_frontend: fix typos in comments and one function

Signed-off-by: Guillaume Audirac <guillaume.audirac@webag.fr>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: tda10048: clear the uncorrected packet registers when saturated

Use the register CLUNC to reset the CPTU registers (LSB & MSB) when they
saturate at 0xFFFF. Fixes as well a few register typos.

Signed-off-by: Guillaume Audirac <guillaume.audirac@webag.fr>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: tda10048: fix bitmask for the transmission mode

Add a missing bit for reading the transmission mode (2K/8K) in
tda10048_get_tps

Signed-off-by: Guillaume Audirac <guillaume.audirac@webag.fr>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: tda10048: fix the uncomplete function tda10048_read_ber

Completes the bit-error-rate read function with the CBER register (before
Viterbi decoder). The returned value is 1e8*actual_ber to be positive.
Also includes some typo mistakes.

Signed-off-by: Guillaume Audirac <guillaume.audirac@webag.fr>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: cx23885: Enable Message Signaled Interrupts(MSI)

Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR/mceusb: unify and simplify different gen device init

Started out as an effort to try to tackle the last remaining issue I'm
having with this damned pinnacle device getting wedged the first time
its plugged in after an indeterminate length of not being plugged in.
Didn't get that solved yet, but did streamline the init code a bit more
and remove some superfluous gunk. Nukes a completely unneeded call to
usb_device_init() and several lines of overly complex crap in the gen1
device init path.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: v4l: Add MPC5121e VIU video capture driver

Adds support for Video-In (VIU) unit of Freescale
MPC5121e. The driver supports RGB888/RGB565 formats,
capture and overlay on MPC5121e DIU frame buffer.

Signed-off-by: Hongjun Chen <hong-jun.chen@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: uvcvideo: Add support for Manta MM-353 Plako

The camera requires the PROBE_MINMAX quirk. Add a corresponding entry
in the device IDs list

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: uvcvideo: Don't use stack-based buffers for USB transfers

Data buffers on the stack are not allowed for USB I/O. Use dynamically
allocated buffers instead when querying control length and control
capabilities.

The control capabilities are now also stored in the uvc_control
structure.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: uvcvideo: Define control information bits using macros

Use the macros instead of hardcoding numerical constants for the
controls information bitfield.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: uvcvideo: Support menu controls in the control mapping API

The UVCIOC_CTRL_MAP ioctl doesn't support menu entries for menu
controls. As the uvc_xu_control_mapping structure has no reserved
fields, this can't be fixed while keeping ABI compatibility.

Modify the UVCIOC_CTRL_MAP ioctl to add menu entries support, and define
UVCIOC_CTRL_MAP_OLD that supports the old ABI without any ability to add
menu controls.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: uvcvideo: Make button controls work properly

According to the v4l2 spec, writing any value to a button control should
result in the action belonging to the button control being triggered.
UVC cams however want to see a 1 written, this patch fixes this by
overriding whatever value user space passed in with -1 (0xffffffff) when
the control is a button control.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: uvcvideo: Add support for absolute pan/tilt controls

Signed-off-by: Martin Rubli <martin_rubli@logitech.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: IR/imon: auto-configure another 0xffdc device variant

Per Pieter Hoekstra:

I have a Antec Fusion with a iMON Lcd and I get the following error:
imon 6-1:1.0: Unknown 0xffdc device, defaulting to VFD and iMON IR (id
0x9e)

The driver is functional if I load it like this: (I do not use a remote for it)
modprobe imon display_type=1 (On Mythbuntu 10.04/2.6.32)

This device is a lcd-type with support for a MCE remote. Looking at
the source code, this device (0x9e) is the same as id 0x9f.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: cx88: Let the user disable IR support

It might be useful to be able to disable the IR support, either for
debugging purposes, or just for users who know they won't use the IR
remote control anyway. On many cards, IR support requires expensive
polling/sampling which is better avoided if never needed.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: cx88: Move I2C IR initialization

Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This is the same as was done for
the bttv driver several months ago. Might solve bugs which have not yet
been reported for some cards. It makes both drivers consistent, and
makes it easier to disable IR support (coming soon.)

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: cx23885: add support for new model revisions of the HVR12xx board family

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: xc5000: Fix a few warnings

drivers/media/common/tuners/xc5000.c: In function ‘xc_write_reg’:
drivers/media/common/tuners/xc5000.c:298: warning: passing argument 3 of ‘xc5000_readreg’ from incompatible pointer type
drivers/media/common/tuners/xc5000.c:235: note: expected ‘u16 *’ but argument is of type ‘u8 *’
drivers/media/common/tuners/xc5000.c: At top level:
drivers/media/common/tuners/xc5000.c:223: warning: ‘xc_read_i2c_data’ defined but not used

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: cx23885: Convert cx23885-input to use new in kernel IR pulse decoders

Convert the cx23885 driver to use the new in kernel IR pulse
decoders for the integrated CX2388[578] IR controllers.  Rip out a lot
of RC-5 decoding related code in the process and rename some variables
for clarity or to more accurately describe their usage.

Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: cx23885: Convert from struct card_ir to struct cx23885_ir_input for IR Rx

Move from the generic, shared card_ir state structure to a cx23885 driver
specific IR state structure in anticipation of moving to the new IR pulse
decoders in the IR core.

Fix up the card name truncation in the dmesg log while we're at it,
by avoiding using fixed length string storage in our new IR state
structure.

Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - main: Simplify image building

The image pointer and its length are now in the main structure instead
of in the frame buffer. They are updated on application vidioc_qbuf and
in the URB interrupt function when ending an image.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: gspca - gl860: Fix a compilation warning

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: vpif: removing VPIF config variables

The Kconfig variables are moved to video/davinci/Kconfig through another
patch and these are to be therefore removed

Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: vpfe_capture: Create separate Kconfig file for davinci devices

Currently VPFE Capture driver and DM6446 CCDC driver is being
reused for AM3517. So this patch is preparing the Kconfig/makefile
for re-use of such IP's.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: tuners:tuner-simple Fix warning: variable 'tun' set but not used

Resend due to a whitespace issue I created by mistake.
The below patch fixes a warning message create by gcc 4.6.0

 CC [M]  drivers/media/common/tuners/tuner-simple.o
drivers/media/common/tuners/tuner-simple.c: In function 'simple_set_tv_freq':
drivers/media/common/tuners/tuner-simple.c:548:20: warning: variable 'tun' set but not used

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: tm6000-input: Make checkpatch.pl happy

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: tm6000: add ir support

Signed-off-by: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: drivers/media/dvb/frontends: remove duplicate structure field  initialization

The read_status field is initialized twice to the same value.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@

struct I s =@p0 { ... .fld@p = E, ...};

@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@

struct I s =@p0 { ... .fld@p = E, ...};

@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@

if int(ps[0].line)<int(pr[0].line) or int(ps[0].column)<int(pr[0].column):
  cocci.print_main(fld,p0)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: xc5000, rework xc_write_reg

Rework xc_write_reg function for correct read register of the xc5000.
It is very useful for tm6000.

Tested for tm6000 and for saa7134 works well.

Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: dvb_ca_en50221: return -EFAULT on copy_to_user errors

copy_to_user() returns the number of bytes remaining to be copied which
isn't the right thing to return here.  The comments say that these
functions in dvb_ca_en50221.c should return the number of bytes copied or
an error return.  I've changed it to return -EFAULT.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>