Florian Westphal [Mon, 19 Feb 2018 00:24:53 +0000 (01:24 +0100)]
netfilter: ebtables: convert BUG_ONs to WARN_ONs
[ Upstream commit
fc6a5d0601c5ac1d02f283a46f60b87b2033e5ca ]
All of these conditions are not fatal and should have
been WARN_ONs from the get-go.
Convert them to WARN_ONs and bail out.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthias Schiffer [Tue, 23 Jan 2018 09:59:50 +0000 (10:59 +0100)]
batman-adv: invalidate checksum on fragment reassembly
[ Upstream commit
3bf2a09da956b43ecfaa630a2ef9a477f991a46a ]
A more sophisticated implementation could try to combine fragment checksums
when all fragments have CHECKSUM_COMPLETE and are split at even offsets.
For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure"
warnings in the kernel log when fragmented frames are received. In
consequence, skb_pull_rcsum() can be replaced with skb_pull().
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes:
610bfc6bc99b ("batman-adv: Receive fragmented packets and merge")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthias Schiffer [Tue, 23 Jan 2018 09:59:49 +0000 (10:59 +0100)]
batman-adv: fix packet checksum in receive path
[ Upstream commit
abd6360591d3f8259f41c34e31ac4826dfe621b8 ]
eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes:
c6c8fea29769 ("net: Add batman-adv meshing protocol")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yufen Yu [Sat, 24 Feb 2018 04:05:56 +0000 (12:05 +0800)]
md/raid1: fix NULL pointer dereference
[ Upstream commit
3de59bb9d551428cbdc76a9ea57883f82e350b4d ]
In handle_write_finished(), if r1_bio->bios[m] != NULL, it thinks
the corresponding conf->mirrors[m].rdev is also not NULL. But, it
is not always true.
Even if some io hold replacement rdev(i.e. rdev->nr_pending.count > 0),
raid1_remove_disk() can also set the rdev as NULL. That means,
bios[m] != NULL, but mirrors[m].rdev is NULL, resulting in NULL
pointer dereference in handle_write_finished and sync_request_write.
This patch can fix BUGs as follows:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000140
IP: [<
ffffffff815bbbbd>] raid1d+0x2bd/0xfc0
PGD
12ab52067 PUD
12f587067 PMD 0
Oops: 0000 [#1] SMP
CPU: 1 PID: 2008 Comm: md3_raid1 Not tainted 4.1.44+ #130
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
Call Trace:
? schedule+0x37/0x90
? prepare_to_wait_event+0x83/0xf0
md_thread+0x144/0x150
? wake_atomic_t_function+0x70/0x70
? md_start_sync+0xf0/0xf0
kthread+0xd8/0xf0
? kthread_worker_fn+0x160/0x160
ret_from_fork+0x42/0x70
? kthread_worker_fn+0x160/0x160
BUG: unable to handle kernel NULL pointer dereference at
00000000000000b8
IP: sync_request_write+0x9e/0x980
PGD
800000007c518067 P4D
800000007c518067 PUD
8002b067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 24 PID: 2549 Comm: md3_raid1 Not tainted 4.15.0+ #118
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
Call Trace:
? sched_clock+0x5/0x10
? sched_clock_cpu+0xc/0xb0
? flush_pending_writes+0x3a/0xd0
? pick_next_task_fair+0x4d5/0x5f0
? __switch_to+0xa2/0x430
raid1d+0x65a/0x870
? find_pers+0x70/0x70
? find_pers+0x70/0x70
? md_thread+0x11c/0x160
md_thread+0x11c/0x160
? finish_wait+0x80/0x80
kthread+0x111/0x130
? kthread_create_worker_on_cpu+0x70/0x70
? do_syscall_64+0x6f/0x190
? SyS_exit_group+0x10/0x10
ret_from_fork+0x35/0x40
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BingJing Chang [Thu, 22 Feb 2018 05:34:46 +0000 (13:34 +0800)]
md: fix a potential deadlock of raid5/raid10 reshape
[ Upstream commit
8876391e440ba615b10eef729576e111f0315f87 ]
There is a potential deadlock if mount/umount happens when
raid5_finish_reshape() tries to grow the size of emulated disk.
How the deadlock happens?
1) The raid5 resync thread finished reshape (expanding array).
2) The mount or umount thread holds VFS sb->s_umount lock and tries to
write through critical data into raid5 emulated block device. So it
waits for raid5 kernel thread handling stripes in order to finish it
I/Os.
3) In the routine of raid5 kernel thread, md_check_recovery() will be
called first in order to reap the raid5 resync thread. That is,
raid5_finish_reshape() will be called. In this function, it will try
to update conf and call VFS revalidate_disk() to grow the raid5
emulated block device. It will try to acquire VFS sb->s_umount lock.
The raid5 kernel thread cannot continue, so no one can handle mount/
umount I/Os (stripes). Once the write-through I/Os cannot be finished,
mount/umount will not release sb->s_umount lock. The deadlock happens.
The raid5 kernel thread is an emulated block device. It is responible to
handle I/Os (stripes) from upper layers. The emulated block device
should not request any I/Os on itself. That is, it should not call VFS
layer functions. (If it did, it will try to acquire VFS locks to
guarantee the I/Os sequence.) So we have the resync thread to send
resync I/O requests and to wait for the results.
For solving this potential deadlock, we can put the size growth of the
emulated block device as the final step of reshape thread.
2017/12/29:
Thanks to Guoqing Jiang <gqjiang@suse.com>,
we confirmed that there is the same deadlock issue in raid10. It's
reproducible and can be fixed by this patch. For raid10.c, we can remove
the similar code to prevent deadlock as well since they has been called
before.
Reported-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Mon, 19 Feb 2018 14:55:55 +0000 (14:55 +0000)]
fs: dcache: Use READ_ONCE when accessing i_dir_seq
[ Upstream commit
8cc07c808c9d595e81cbe5aad419b7769eb2e5c9 ]
i_dir_seq is subject to concurrent modification by a cmpxchg or
store-release operation, so ensure that the relaxed access in
d_alloc_parallel uses READ_ONCE.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Mon, 19 Feb 2018 14:55:54 +0000 (14:55 +0000)]
fs: dcache: Avoid livelock between d_alloc_parallel and __d_add
[ Upstream commit
015555fd4d2930bc0c86952c46ad88b3392f66e4 ]
If d_alloc_parallel runs concurrently with __d_add, it is possible for
d_alloc_parallel to continuously retry whilst i_dir_seq has been
incremented to an odd value by __d_add:
CPU0:
__d_add
n = start_dir_add(dir);
cmpxchg(&dir->i_dir_seq, n, n + 1) == n
CPU1:
d_alloc_parallel
retry:
seq = smp_load_acquire(&parent->d_inode->i_dir_seq) & ~1;
hlist_bl_lock(b);
bit_spin_lock(0, (unsigned long *)b); // Always succeeds
CPU0:
__d_lookup_done(dentry)
hlist_bl_lock
bit_spin_lock(0, (unsigned long *)b); // Never succeeds
CPU1:
if (unlikely(parent->d_inode->i_dir_seq != seq)) {
hlist_bl_unlock(b);
goto retry;
}
Since the simple bit_spin_lock used to implement hlist_bl_lock does not
provide any fairness guarantees, then CPU1 can starve CPU0 of the lock
and prevent it from reaching end_dir_add(dir), therefore CPU1 cannot
exit its retry loop because the sequence number always has the bottom
bit set.
This patch resolves the livelock by not taking hlist_bl_lock in
d_alloc_parallel if the sequence counter is odd, since any subsequent
masked comparison with i_dir_seq will fail anyway.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Naresh Madhusudana <naresh.madhusudana@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Ott [Thu, 22 Feb 2018 12:05:41 +0000 (13:05 +0100)]
kvm: fix warning for CONFIG_HAVE_KVM_EVENTFD builds
[ Upstream commit
076467490b8176eb96eddc548a14d4135c7b5852 ]
Move the kvm_arch_irq_routing_update() prototype outside of
ifdef CONFIG_HAVE_KVM_EVENTFD guards to fix the following sparse warning:
arch/s390/kvm/../../../virt/kvm/irqchip.c:171:28: warning: symbol 'kvm_arch_irq_routing_update' was not declared. Should it be static?
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Kodanev [Thu, 22 Feb 2018 15:20:30 +0000 (18:20 +0300)]
macvlan: fix use-after-free in macvlan_common_newlink()
[ Upstream commit
4e14bf4236490306004782813b8b4494b18f5e60 ]
The following use-after-free was reported by KASan when running
LTP macvtap01 test on 4.16-rc2:
[10642.528443] BUG: KASAN: use-after-free in
macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10642.626607] Read of size 8 at addr
ffff880ba49f2100 by task ip/18450
...
[10642.963873] Call Trace:
[10642.994352] dump_stack+0x5c/0x7c
[10643.035325] print_address_description+0x75/0x290
[10643.092938] kasan_report+0x28d/0x390
[10643.137971] ? macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.207963] macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.275978] macvtap_newlink+0x171/0x260 [macvtap]
[10643.334532] rtnl_newlink+0xd4f/0x1300
...
[10646.256176] Allocated by task 18450:
[10646.299964] kasan_kmalloc+0xa6/0xd0
[10646.343746] kmem_cache_alloc_trace+0xf1/0x210
[10646.397826] macvlan_common_newlink+0x6de/0x14a0 [macvlan]
[10646.464386] macvtap_newlink+0x171/0x260 [macvtap]
[10646.522728] rtnl_newlink+0xd4f/0x1300
...
[10647.022028] Freed by task 18450:
[10647.061549] __kasan_slab_free+0x138/0x180
[10647.111468] kfree+0x9e/0x1c0
[10647.147869] macvlan_port_destroy+0x3db/0x650 [macvlan]
[10647.211411] rollback_registered_many+0x5b9/0xb10
[10647.268715] rollback_registered+0xd9/0x190
[10647.319675] register_netdevice+0x8eb/0xc70
[10647.370635] macvlan_common_newlink+0xe58/0x14a0 [macvlan]
[10647.437195] macvtap_newlink+0x171/0x260 [macvtap]
Commit
d02fd6e7d293 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:
* for macvlan it always returns NULL because 'lowerdev' is the one that
was used to register rx handler (port) in macvlan_port_create() as
well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
its own rx handler before macvlan_common_newlink().
Fixes:
d02fd6e7d293 ("macvlan: Fix one possible double free")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pratyush Anand [Mon, 5 Feb 2018 13:28:01 +0000 (14:28 +0100)]
arm64: fix unwind_frame() for filtered out fn for function graph tracing
[ Upstream commit
9f416319f40cd857d2bb517630e5855a905ef3fb ]
do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).
Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.
Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().
This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.
Reproducer:
cd /sys/kernel/debug/tracing/
echo schedule > set_graph_notrace
echo 1 > options/display-graph
echo wakeup > current_tracer
ps -ef | grep -i agent
Above commands result in:
Unable to handle kernel paging request at virtual address
ffff801bd3d1e000
pgd =
ffff8003cbe97c00
[
ffff801bd3d1e000] *pgd=
0000000000000000, *pud=
0000000000000000
Internal error: Oops:
96000006 [#1] SMP
[...]
CPU: 5 PID: 11696 Comm: ps Not tainted 4.11.0+ #33
[...]
task:
ffff8003c21ba000 task.stack:
ffff8003cc6c0000
PC is at unwind_frame+0x12c/0x180
LR is at get_wchan+0xd4/0x134
pc : [<
ffff00000808892c>] lr : [<
ffff0000080860b8>] pstate:
60000145
sp :
ffff8003cc6c3ab0
x29:
ffff8003cc6c3ab0 x28:
0000000000000001
x27:
0000000000000026 x26:
0000000000000026
x25:
00000000000012d8 x24:
0000000000000000
x23:
ffff8003c1c04000 x22:
ffff000008c83000
x21:
ffff8003c1c00000 x20:
000000000000000f
x19:
ffff8003c1bc0000 x18:
0000fffffc593690
x17:
0000000000000000 x16:
0000000000000001
x15:
0000b855670e2b60 x14:
0003e97f22cf1d0f
x13:
0000000000000001 x12:
0000000000000000
x11:
00000000e8f4883e x10:
0000000154f47ec8
x9 :
0000000070f367c0 x8 :
0000000000000000
x7 :
00008003f7290000 x6 :
0000000000000018
x5 :
0000000000000000 x4 :
ffff8003c1c03cb0
x3 :
ffff8003c1c03ca0 x2 :
00000017ffe80000
x1 :
ffff8003cc6c3af8 x0 :
ffff8003d3e9e000
Process ps (pid: 11696, stack limit = 0xffff8003cc6c0000)
Stack: (0xffff8003cc6c3ab0 to 0xffff8003cc6c4000)
[...]
[<
ffff00000808892c>] unwind_frame+0x12c/0x180
[<
ffff000008305008>] do_task_stat+0x864/0x870
[<
ffff000008305c44>] proc_tgid_stat+0x3c/0x48
[<
ffff0000082fde0c>] proc_single_show+0x5c/0xb8
[<
ffff0000082b27e0>] seq_read+0x160/0x414
[<
ffff000008289e6c>] __vfs_read+0x58/0x164
[<
ffff00000828b164>] vfs_read+0x88/0x144
[<
ffff00000828c2e8>] SyS_read+0x60/0xc0
[<
ffff0000080834a0>] __sys_trace_return+0x0/0x4
Fixes:
20380bb390a4 (arm64: ftrace: fix a stack tracer's output under function graph tracer)
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
[catalin.marinas@arm.com: replace WARN_ON with WARN_ON_ONCE]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Fri, 23 Feb 2018 09:06:03 +0000 (10:06 +0100)]
mac80211: drop frames with unexpected DS bits from fast-rx to slow path
[ Upstream commit
b323ac19b7734a1c464b2785a082ee50bccd3b91 ]
Fixes rx for 4-addr packets in AP mode. These may be used for setting
up a 4-addr link for stations that are allowed to do so.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samuel Neves [Wed, 21 Feb 2018 20:50:36 +0000 (20:50 +0000)]
x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations
[ Upstream commit
4596749339e06dc7a424fc08a15eded850ed78b7 ]
Without this fix, /proc/cpuinfo will display an incorrect amount
of CPU cores, after bringing them offline and online again, as
exemplified below:
$ cat /proc/cpuinfo | grep cores
cpu cores : 4
cpu cores : 8
cpu cores : 8
cpu cores : 20
cpu cores : 4
cpu cores : 3
cpu cores : 2
cpu cores : 2
This patch fixes this by always zeroing the booted_cores variable
upon turning off a logical CPU.
Tested-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Samuel Neves <sneves@dei.uc.pt>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jgross@suse.com
Cc: luto@kernel.org
Cc: prarit@redhat.com
Cc: vkuznets@redhat.com
Link: http://lkml.kernel.org/r/20180221205036.5244-1-sneves@dei.uc.pt
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrea Parri [Thu, 22 Feb 2018 09:24:48 +0000 (10:24 +0100)]
locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs
[ Upstream commit
472e8c55cf6622d1c112dc2bc777f68bbd4189db ]
Successful RMW operations are supposed to be fully ordered, but
Alpha's xchg() and cmpxchg() do not meet this requirement.
Will Deacon noticed the bug:
> So MP using xchg:
>
> WRITE_ONCE(x, 1)
> xchg(y, 1)
>
> smp_load_acquire(y) == 1
> READ_ONCE(x) == 0
>
> would be allowed.
... which thus violates the above requirement.
Fix it by adding a leading smp_mb() to the xchg() and cmpxchg() implementations.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-alpha@vger.kernel.org
Link: http://lkml.kernel.org/r/1519291488-5752-1-git-send-email-parri.andrea@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Tue, 13 Feb 2018 01:26:20 +0000 (17:26 -0800)]
integrity/security: fix digsig.c build error with header file
[ Upstream commit
120f3b11ef88fc38ce1d0ff9c9a4b37860ad3140 ]
security/integrity/digsig.c has build errors on some $ARCH due to a
missing header file, so add it.
security/integrity/digsig.c:146:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: linux-integrity@vger.kernel.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Thu, 22 Feb 2018 19:55:28 +0000 (20:55 +0100)]
regulatory: add NUL to request alpha2
[ Upstream commit
657308f73e674e86b60509a430a46e569bf02846 ]
Similar to the ancient commit
a5fe8e7695dc ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.
Fixes:
73d54c9e74c4 ("cfg80211: add regulatory netlink multicast group")
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Wed, 21 Feb 2018 05:42:26 +0000 (21:42 -0800)]
smsc75xx: fix smsc75xx_set_features()
[ Upstream commit
88e80c62671ceecdbb77c902731ec95a4bfa62f9 ]
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren [Thu, 22 Feb 2018 18:02:49 +0000 (10:02 -0800)]
ARM: OMAP: Fix dmtimer init for omap1
[ Upstream commit
ba6887836178d43b3665b9da075c2c5dfe1d207c ]
We need to enable PM runtime on omap1 also as otherwise we
will get errors:
omap_timer omap_timer.1: omap_dm_timer_probe: pm_runtime_get_sync failed!
omap_timer: probe of omap_timer.1 failed with error -13
...
We are checking for OMAP_TIMER_NEEDS_RESET flag elsewhere so this is
safe to do.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Thu, 22 Feb 2018 14:38:33 +0000 (14:38 +0000)]
PKCS#7: fix direct verification of SignerInfo signature
[ Upstream commit
6459ae386699a5fe0dc52cf30255f75274fa43a4 ]
If none of the certificates in a SignerInfo's certificate chain match a
trusted key, nor is the last certificate signed by a trusted key, then
pkcs7_validate_trust_one() tries to check whether the SignerInfo's
signature was made directly by a trusted key. But, it actually fails to
set the 'sig' variable correctly, so it actually verifies the last
signature seen. That will only be the SignerInfo's signature if the
certificate chain is empty; otherwise it will actually be the last
certificate's signature.
This is not by itself a security problem, since verifying any of the
certificates in the chain should be sufficient to verify the SignerInfo.
Still, it's not working as intended so it should be fixed.
Fix it by setting 'sig' correctly for the direct verification case.
Fixes:
757932e6da6d ("PKCS#7: Handle PKCS#7 messages that contain no X.509 certs")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Ott [Mon, 12 Feb 2018 11:01:03 +0000 (12:01 +0100)]
s390/cio: clear timer when terminating driver I/O
[ Upstream commit
410d5e13e7638bc146321671e223d56495fbf3c7 ]
When we terminate driver I/O (because we need to stop using a certain
channel path) we also need to ensure that a timer (which may have been
set up using ccw_device_start_timeout) is cleared.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Ott [Wed, 7 Feb 2018 12:18:19 +0000 (13:18 +0100)]
s390/cio: fix return code after missing interrupt
[ Upstream commit
770b55c995d171f026a9efb85e71e3b1ea47b93d ]
When a timeout occurs for users of ccw_device_start_timeout
we will stop the IO and call the drivers int handler with
the irb pointer set to ERR_PTR(-ETIMEDOUT). Sometimes
however we'd set the irb pointer to ERR_PTR(-EIO) which is
not intended. Just set the correct value in all codepaths.
Reported-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Ott [Tue, 6 Feb 2018 13:59:43 +0000 (14:59 +0100)]
s390/cio: fix ccw_device_start_timeout API
[ Upstream commit
f97a6b6c47d2f329a24f92cc0ca3c6df5727ba73 ]
There are cases a device driver can't start IO because the device is
currently in use by cio. In this case the device driver is notified
when the device is usable again.
Using ccw_device_start_timeout we would set the timeout (and change
an existing timeout) before we test for internal usage. Worst case
this could lead to an unexpected timer deletion.
Fix this by setting the timeout after we test for internal usage.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Lord [Tue, 20 Feb 2018 19:49:20 +0000 (14:49 -0500)]
powerpc/bpf/jit: Fix 32-bit JIT for seccomp_data access
[ Upstream commit
083b20907185b076f21c265b30fe5b5f24c03d8c ]
I am using SECCOMP to filter syscalls on a ppc32 platform, and noticed
that the JIT compiler was failing on the BPF even though the
interpreter was working fine.
The issue was that the compiler was missing one of the instructions
used by SECCOMP, so here is a patch to enable JIT for that
instruction.
Fixes:
eb84bab0fb38 ("ppc: Kconfig: Enable BPF JIT on ppc32")
Signed-off-by: Mark Lord <mlord@pobox.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Rientjes [Wed, 21 Feb 2018 22:45:32 +0000 (14:45 -0800)]
kernel/relay.c: limit kmalloc size to KMALLOC_MAX_SIZE
[ Upstream commit
88913bd8ea2a75d7e460a4bed5f75e1c32660d7e ]
chan->n_subbufs is set by the user and relay_create_buf() does a kmalloc()
of chan->n_subbufs * sizeof(size_t *).
kmalloc_slab() will generate a warning when this fails if
chan->subbufs * sizeof(size_t *) > KMALLOC_MAX_SIZE.
Limit chan->n_subbufs to the maximum allowed kmalloc() size.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1802061216100.122576@chino.kir.corp.google.com
Fixes:
f6302f1bcd75 ("relay: prevent integer overflow in relay_open()")
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Tue, 20 Feb 2018 13:09:11 +0000 (14:09 +0100)]
md: raid5: avoid string overflow warning
[ Upstream commit
53b8d89ddbdbb0e4625a46d2cdbb6f106c52f801 ]
gcc warns about a possible overflow of the kmem_cache string, when adding
four characters to a string of the same length:
drivers/md/raid5.c: In function 'setup_conf':
drivers/md/raid5.c:2207:34: error: '-alt' directive writing 4 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~
drivers/md/raid5.c:2207:2: note: 'sprintf' output between 5 and 36 bytes into a destination of size 32
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If I'm counting correctly, we need 11 characters for the fixed part
of the string and 18 characters for a 64-bit pointer (when no gendisk
is used), so that leaves three characters for conf->level, which should
always be sufficient.
This makes the code use snprintf() with the correct length, to
make the code more robust against changes, and to get the compiler
to shut up.
In commit
f4be6b43f1ac ("md/raid5: ensure we create a unique name for
kmem_cache when mddev has no gendisk") from 2010, Neil said that
the pointer could be removed "shortly" once devices without gendisk
are disallowed. I have no idea if that happened, but if it did, that
should probably be changed as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrea Parri [Tue, 20 Feb 2018 18:45:56 +0000 (19:45 +0100)]
locking/xchg/alpha: Add unconditional memory barrier to cmpxchg()
[ Upstream commit
cb13b424e986aed68d74cbaec3449ea23c50e167 ]
Continuing along with the fight against smp_read_barrier_depends() [1]
(or rather, against its improper use), add an unconditional barrier to
cmpxchg. This guarantees that dependency ordering is preserved when a
dependency is headed by an unsuccessful cmpxchg. As it turns out, the
change could enable further simplification of LKMM as proposed in [2].
[1] https://marc.info/?l=linux-kernel&m=
150884953419377&w=2
https://marc.info/?l=linux-kernel&m=
150884946319353&w=2
https://marc.info/?l=linux-kernel&m=
151215810824468&w=2
https://marc.info/?l=linux-kernel&m=
151215816324484&w=2
[2] https://marc.info/?l=linux-kernel&m=
151881978314872&w=2
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-alpha@vger.kernel.org
Link: http://lkml.kernel.org/r/1519152356-4804-1-git-send-email-parri.andrea@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Mon, 5 Feb 2018 20:09:59 +0000 (21:09 +0100)]
drm/exynos: fix comparison to bitshift when dealing with a mask
[ Upstream commit
1293b6191010672c0c9dacae8f71c6f3e4d70cbe ]
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Wed, 17 Jan 2018 17:01:21 +0000 (18:01 +0100)]
drm/exynos: g2d: use monotonic timestamps
[ Upstream commit
a588a8bb7b25a3fb4f7fed00feb7aec541fc2632 ]
The exynos DRM driver uses real-time 'struct timeval' values
for exporting its timestamps to user space. This has multiple
problems:
1. signed seconds overflow in y2038
2. the 'struct timeval' definition is deprecated in the kernel
3. time may jump or go backwards after a 'settimeofday()' syscall
4. other DRM timestamps are in CLOCK_MONOTONIC domain, so they
can't be compared
5. exporting microseconds requires a division by 1000, which may
be slow on some architectures.
The code existed in two places before, but the IPP portion was
removed in
8ded59413ccc ("drm/exynos: ipp: Remove Exynos DRM
IPP subsystem"), so we no longer need to worry about it.
Ideally timestamps should just use 64-bit nanoseconds instead, but
of course we can't change that now. Instead, this tries to address
the first four points above by using monotonic 'timespec' values.
According to Tobias Jakobi, user space doesn't care about the
timestamp at the moment, so we can change the format. Even if
there is something looking at them, it will work just fine with
monotonic times as long as the application only looks at the
relative values between two events.
Link: https://patchwork.kernel.org/patch/10038593/
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yufen Yu [Tue, 6 Feb 2018 09:39:15 +0000 (17:39 +0800)]
md raid10: fix NULL deference in handle_write_completed()
[ Upstream commit
01a69cab01c184d3786af09e9339311123d63d22 ]
In the case of 'recover', an r10bio with R10BIO_WriteError &
R10BIO_IsRecover will be progressed by handle_write_completed().
This function traverses all r10bio->devs[copies].
If devs[m].repl_bio != NULL, it thinks conf->mirrors[dev].replacement
is also not NULL. However, this is not always true.
When there is an rdev of raid10 has replacement, then each r10bio
->devs[m].repl_bio != NULL in conf->r10buf_pool. However, in 'recover',
even if corresponded replacement is NULL, it doesn't clear r10bio
->devs[m].repl_bio, resulting in replacement NULL deference.
This bug was introduced when replacement support for raid10 was
added in Linux 3.3.
As NeilBrown suggested:
Elsewhere the determination of "is this device part of the
resync/recovery" is made by resting bio->bi_end_io.
If this is end_sync_write, then we tried to write here.
If it is NULL, then we didn't try to write.
Fixes:
9ad1aefc8ae8 ("md/raid10: Handle replacement devices during resync.")
Cc: stable (V3.3+)
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilan Peer [Mon, 19 Feb 2018 12:48:42 +0000 (14:48 +0200)]
mac80211: Do not disconnect on invalid operating class
[ Upstream commit
191da271ac260700db3e5b4bb982a17ca78769d6 ]
Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.
However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.
To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sara Sharon [Mon, 19 Feb 2018 12:48:37 +0000 (14:48 +0200)]
mac80211: fix calling sleeping function in atomic context
[ Upstream commit
95f3ce6a77893ac828ba841df44421620de4314b ]
sta_info_alloc can be called from atomic paths (such as RX path)
so we need to call pcpu_alloc with the correct gfp.
Fixes:
c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sara Sharon [Mon, 19 Feb 2018 12:48:35 +0000 (14:48 +0200)]
mac80211: fix a possible leak of station stats
[ Upstream commit
d78d9ee9d40aca4781d2c5334972544601a4c3a2 ]
If sta_info_alloc fails after allocating the per CPU statistics,
they are not properly freed.
Fixes:
c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Sat, 10 Feb 2018 12:20:34 +0000 (13:20 +0100)]
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
[ Upstream commit
651b9920d7a694ffb1f885aef2bbb068a25d9d66 ]
This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Thu, 15 Feb 2018 22:59:00 +0000 (22:59 +0000)]
rxrpc: Work around usercopy check
[ Upstream commit
a16b8d0cf2ec1e626d24bc2a7b9e64ace6f7501d ]
Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted. This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer. A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.
Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().
The warning generated looks like:
Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLUB object 'dmaengine-unmap-128' (offset 680, size 8)!
WARNING: CPU: 0 PID: 1401 at mm/usercopy.c:81 usercopy_warn+0x7e/0xa0
...
RIP: 0010:usercopy_warn+0x7e/0xa0
...
Call Trace:
__check_object_size+0x9c/0x1a0
put_cmsg+0x98/0x120
rxrpc_recvmsg+0x6fc/0x1010 [rxrpc]
? finish_wait+0x80/0x80
___sys_recvmsg+0xf8/0x240
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? finish_task_switch+0xa6/0x2b0
? trace_hardirqs_on_caller+0xed/0x180
? _raw_spin_unlock_irq+0x29/0x40
? __sys_recvmsg+0x4e/0x90
__sys_recvmsg+0x4e/0x90
do_syscall_64+0x7a/0x220
entry_SYSCALL_64_after_hwframe+0x26/0x9b
Reported-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook [Wed, 14 Feb 2018 23:45:07 +0000 (15:45 -0800)]
NFC: llcp: Limit size of SDP URI
[ Upstream commit
fe9c842695e26d8116b61b80bfb905356f07834b ]
The tlv_len is u8, so we need to limit the size of the SDP URI. Enforce
this both in the NLA policy and in the code that performs the allocation
and copy, to avoid writing past the end of the allocated buffer.
Fixes:
d9b8d8e19b073 ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naftali Goldstein [Thu, 28 Dec 2017 13:53:04 +0000 (15:53 +0200)]
iwlwifi: mvm: always init rs with 20mhz bandwidth rates
[ Upstream commit
6b7a5aea71b342ec0593d23b08383e1f33da4c9a ]
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sara Sharon [Tue, 29 Mar 2016 07:56:57 +0000 (10:56 +0300)]
iwlwifi: mvm: fix security bug in PN checking
[ Upstream commit
5ab2ba931255d8bf03009c06d58dce97de32797c ]
A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.
This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.
Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.
Fixes:
f1ae02b186d9 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Falcon [Wed, 14 Feb 2018 00:23:42 +0000 (18:23 -0600)]
ibmvnic: Free RX socket buffer in case of adapter error
[ Upstream commit
4b9b0f01350500173f17e2b2e65beb4df4ef99c7 ]
If a RX buffer is returned to the client driver with an error, free the
corresponding socket buffer before continuing.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Tue, 2 Jan 2018 15:25:35 +0000 (16:25 +0100)]
ARM: OMAP1: clock: Fix debugfs_create_*() usage
[ Upstream commit
8cbbf1745dcde7ba7e423dc70619d223de90fd43 ]
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, depending on data type.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
Correct all wrong usage:
- clk.rate is unsigned long, not u32,
- clk.flags is u8, not u32, which exposed the successive
clk.rate_offset and clk.src_offset fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren [Fri, 9 Feb 2018 16:15:53 +0000 (08:15 -0800)]
ARM: OMAP3: Fix prm wake interrupt for resume
[ Upstream commit
d3be6d2a08bd26580562d9714d3d97ea9ba22c73 ]
For platform_suspend_ops, the finish call is too late to re-enable wake
irqs and we need re-enable wake irqs on wake call instead.
Otherwise noirq resume for devices has already happened. And then
dev_pm_disarm_wake_irq() has already disabled the dedicated wake irqs
when the interrupt triggers and the wake irq is never handled.
For devices that are already in PM runtime suspended state when we
enter suspend this means that a possible wake irq will never trigger.
And this can lead into a situation where a device has a pending padconf
wake irq, and the device will stay unresponsive to any further wake
irqs.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. Then try to wake up the system by typing to the serial
console.
Note that this affects only omap3 PRM interrupt as that's currently
the only omap variant that does anything in omap_pm_wake().
In general, for the wake irqs to work, the interrupt must have either
IRQF_NO_SUSPEND or IRQF_EARLY_RESUME set for it to trigger before
dev_pm_disarm_wake_irq() disables the wake irqs.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qi Hou [Thu, 11 Jan 2018 04:54:43 +0000 (12:54 +0800)]
ARM: OMAP2+: timer: fix a kmemleak caused in omap_get_timer_dt
[ Upstream commit
db35340c536f1af0108ec9a0b2126a05d358d14a ]
When more than one GP timers are used as kernel system timers and the
corresponding nodes in device-tree are marked with the same "disabled"
property, then the "attr" field of the property will be initialized
more than once as the property being added to sys file system via
__of_add_property_sysfs().
In __of_add_property_sysfs(), the "name" field of pp->attr.attr is set
directly to the return value of safe_name(), without taking care of
whether it's already a valid pointer to a memory block. If it is, its
old value will always be overwritten by the new one and the memory block
allocated before will a "ghost", then a kmemleak happened.
That the same "disabled" property being added to different nodes of device
tree would cause that kind of kmemleak overhead, at least once.
To fix it, allocate the property dynamically, and delete static one.
Signed-off-by: Qi Hou <qi.hou@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anders Roxell [Tue, 6 Feb 2018 22:20:44 +0000 (16:20 -0600)]
selftests: memfd: add config fragment for fuse
[ Upstream commit
9a606f8d55cfc932ec02172aaed4124fdc150047 ]
The memfd test requires to insert the fuse module (CONFIG_FUSE_FS).
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naresh Kamboju [Wed, 7 Feb 2018 09:17:20 +0000 (14:47 +0530)]
selftests: pstore: Adding config fragment CONFIG_PSTORE_RAM=m
[ Upstream commit
9a379e77033f02c4a071891afdf0f0a01eff8ccb ]
pstore_tests and pstore_post_reboot_tests need CONFIG_PSTORE_RAM=m
Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dong Bo [Fri, 26 Jan 2018 03:21:49 +0000 (11:21 +0800)]
libata: Fix compile warning with ATA_DEBUG enabled
[ Upstream commit
0d3e45bc6507bd1f8728bf586ebd16c2d9e40613 ]
This fixs the following comile warnings with ATA_DEBUG enabled,
which detected by Linaro GCC 5.2-2015.11:
drivers/ata/libata-scsi.c: In function 'ata_scsi_dump_cdb':
./include/linux/kern_levels.h:5:18: warning: format '%d' expects
argument of type 'int', but argument 6 has type 'u64 {aka long
long unsigned int}' [-Wformat=]
tj: Patch hand-applied and description trimmed.
Signed-off-by: Dong Bo <dongbo4@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Wang [Sun, 11 Feb 2018 03:28:12 +0000 (11:28 +0800)]
ptr_ring: prevent integer overflow when calculating size
[ Upstream commit
54e02162d4454a99227f520948bf4494c3d972d0 ]
Switch to use dividing to prevent integer overflow when size is too
big to calculate allocation size properly.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Fixes:
6e6e41c31122 ("ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ulf Magnusson [Mon, 5 Feb 2018 01:21:31 +0000 (02:21 +0100)]
ARC: Fix malformed ARC_EMUL_UNALIGNED default
[ Upstream commit
827cc2fa024dd6517d62de7a44c7b42f32af371b ]
'default N' should be 'default n', though they happen to have the same
effect here, due to undefined symbols (N in this case) evaluating to n
in a tristate sense.
Remove the default from ARC_EMUL_UNALIGNED instead of changing it. bool
and tristate symbols implicitly default to n.
Discovered with the
https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_ulfalizer_Kconfiglib_blob_master_examples_list-5Fundefined.py&d=DwIBAg&c=DPL6_X_6JkXFx7AXWqB0tg&r=c14YS-cH-kdhTOW89KozFhBtBJgs1zXscZojEZQ0THs&m=WxxD8ozR7QQUVzNCBksiznaisBGO_crN7PBOvAoju8s&s=1LmxsNqxwT-7wcInVpZ6Z1J27duZKSoyKxHIJclXU_M&e=
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Salter [Fri, 2 Feb 2018 14:20:29 +0000 (09:20 -0500)]
irqchip/gic-v3: Change pr_debug message to pr_devel
[ Upstream commit
b6dd4d83dc2f78cebc9a7e6e7e4bc2be4d29b94d ]
The pr_debug() in gic-v3 gic_send_sgi() can trigger a circular locking
warning:
GICv3: CPU10: ICC_SGI1R_EL1
5000400
======================================================
WARNING: possible circular locking dependency detected
4.15.0+ #1 Tainted: G W
------------------------------------------------------
dynamic_debug01/1873 is trying to acquire lock:
((console_sem).lock){-...}, at: [<
0000000099c891ec>] down_trylock+0x20/0x4c
but task is already holding lock:
(&rq->lock){-.-.}, at: [<
00000000842e1587>] __task_rq_lock+0x54/0xdc
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&rq->lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock+0x4c/0x60
task_fork_fair+0x3c/0x148
sched_fork+0x10c/0x214
copy_process.isra.32.part.33+0x4e8/0x14f0
_do_fork+0xe8/0x78c
kernel_thread+0x48/0x54
rest_init+0x34/0x2a4
start_kernel+0x45c/0x488
-> #1 (&p->pi_lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
try_to_wake_up+0x48/0x600
wake_up_process+0x28/0x34
__up.isra.0+0x60/0x6c
up+0x60/0x68
__up_console_sem+0x4c/0x7c
console_unlock+0x328/0x634
vprintk_emit+0x25c/0x390
dev_vprintk_emit+0xc4/0x1fc
dev_printk_emit+0x88/0xa8
__dev_printk+0x58/0x9c
_dev_info+0x84/0xa8
usb_new_device+0x100/0x474
hub_port_connect+0x280/0x92c
hub_event+0x740/0xa84
process_one_work+0x240/0x70c
worker_thread+0x60/0x400
kthread+0x110/0x13c
ret_from_fork+0x10/0x18
-> #0 ((console_sem).lock){-...}:
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
other info that might help us debug this:
Chain exists of:
(console_sem).lock --> &p->pi_lock --> &rq->lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&rq->lock);
lock(&p->pi_lock);
lock(&rq->lock);
lock((console_sem).lock);
*** DEADLOCK ***
2 locks held by dynamic_debug01/1873:
#0: (&p->pi_lock){-.-.}, at: [<
000000001366df53>] wake_up_new_task+0x40/0x470
#1: (&rq->lock){-.-.}, at: [<
00000000842e1587>] __task_rq_lock+0x54/0xdc
stack backtrace:
CPU: 10 PID: 1873 Comm: dynamic_debug01 Tainted: G W 4.15.0+ #1
Hardware name: GIGABYTE R120-T34-00/MT30-GS2-00, BIOS T48 10/02/2017
Call trace:
dump_backtrace+0x0/0x188
show_stack+0x24/0x2c
dump_stack+0xa4/0xe0
print_circular_bug.isra.31+0x29c/0x2b8
check_prev_add.constprop.39+0x6c8/0x6dc
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
GICv3: CPU0: ICC_SGI1R_EL1 12000
This could be fixed with printk_deferred() but that might lessen its
usefulness for debugging. So change it to pr_devel to keep it out of
production kernels. Developers working on gic-v3 can enable it as
needed in their kernels.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Kelley [Wed, 14 Feb 2018 02:54:03 +0000 (02:54 +0000)]
cpumask: Make for_each_cpu_wrap() available on UP as well
[ Upstream commit
d207af2eab3f8668b95ad02b21930481c42806fd ]
for_each_cpu_wrap() was originally added in the #else half of a
large "#if NR_CPUS == 1" statement, but was omitted in the #if
half. This patch adds the missing #if half to prevent compile
errors when NR_CPUS is 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michael Kelley <mhkelley@outlook.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kys@microsoft.com
Cc: martin.petersen@oracle.com
Cc: mikelley@microsoft.com
Fixes:
c743f0a5c50f ("sched/fair, cpumask: Export for_each_cpu_wrap()")
Link: http://lkml.kernel.org/r/SN6PR1901MB2045F087F59450507D4FCC17CBF50@SN6PR1901MB2045.namprd19.prod.outlook.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Boyd [Thu, 1 Feb 2018 17:03:29 +0000 (09:03 -0800)]
irqchip/gic-v3: Ignore disabled ITS nodes
[ Upstream commit
95a2562590c2f64a0398183f978d5cf3db6d0284 ]
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Tue, 13 Feb 2018 13:22:57 +0000 (13:22 +0000)]
locking/qspinlock: Ensure node->count is updated before initialising node
[ Upstream commit
11dc13224c975efcec96647a4768a6f1bb7a19a8 ]
When queuing on the qspinlock, the count field for the current CPU's head
node is incremented. This needn't be atomic because locking in e.g. IRQ
context is balanced and so an IRQ will return with node->count as it
found it.
However, the compiler could in theory reorder the initialisation of
node[idx] before the increment of the head node->count, causing an
IRQ to overwrite the initialised node and potentially corrupt the lock
state.
Avoid the potential for this harmful compiler reordering by placing a
barrier() between the increment of the head node->count and the subsequent
node initialisation.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518528177-19169-3-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jia Zhang [Mon, 12 Feb 2018 14:44:53 +0000 (22:44 +0800)]
vfs/proc/kcore, x86/mm/kcore: Fix SMAP fault when dumping vsyscall user page
[ Upstream commit
595dd46ebfc10be041a365d0a3fa99df50b6ba73 ]
Commit:
df04abfd181a ("fs/proc/kcore.c: Add bounce buffer for ktext data")
... introduced a bounce buffer to work around CONFIG_HARDENED_USERCOPY=y.
However, accessing the vsyscall user page will cause an SMAP fault.
Replace memcpy() with copy_from_user() to fix this bug works, but adding
a common way to handle this sort of user page may be useful for future.
Currently, only vsyscall page requires KCORE_USER.
Signed-off-by: Jia Zhang <zhang.jia@linux.alibaba.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jolsa@redhat.com
Link: http://lkml.kernel.org/r/1518446694-21124-2-git-send-email-zhang.jia@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Fri, 9 Feb 2018 13:49:44 +0000 (14:49 +0100)]
bpf: fix rlimit in reuseport net selftest
[ Upstream commit
941ff6f11c020913f5cddf543a9ec63475d7c082 ]
Fix two issues in the reuseport_bpf selftests that were
reported by Linaro CI:
[...]
+ ./reuseport_bpf
---- IPv4 UDP ----
Testing EBPF mod 10...
Reprograming, testing mod 5...
./reuseport_bpf: ebpf error. log:
0: (bf) r6 = r1
1: (20) r0 = *(u32 *)skb[0]
2: (97) r0 %= 10
3: (95) exit
processed 4 insns
: Operation not permitted
+ echo FAIL
[...]
---- IPv4 TCP ----
Testing EBPF mod 10...
./reuseport_bpf: failed to bind send socket: Address already in use
+ echo FAIL
[...]
For the former adjust rlimit since this was the cause of
failure for loading the BPF prog, and for the latter add
SO_REUSEADDR.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://bugs.linaro.org/show_bug.cgi?id=3502
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesper Dangaard Brouer [Thu, 8 Feb 2018 11:48:32 +0000 (12:48 +0100)]
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
[ Upstream commit
e3d91b0ca523d53158f435a3e13df7f0cb360ea2 ]
V3: More generic skipping of relo-section (suggested by Daniel)
If clang >= 4.0.1 is missing the option '-target bpf', it will cause
llc/llvm to create two ELF sections for "Exception Frames", with
section names '.eh_frame' and '.rel.eh_frame'.
The BPF ELF loader library libbpf fails when loading files with these
sections. The other in-kernel BPF ELF loader in samples/bpf/bpf_load.c,
handle this gracefully. And iproute2 loader also seems to work with these
"eh" sections.
The issue in libbpf is caused by bpf_object__elf_collect() skipping
some sections, and later when performing relocation it will be
pointing to a skipped section, as these sections cannot be found by
bpf_object__find_prog_by_idx() in bpf_object__collect_reloc().
This is a general issue that also occurs for other sections, like
debug sections which are also skipped and can have relo section.
As suggested by Daniel. To avoid keeping state about all skipped
sections, instead perform a direct qlookup in the ELF object. Lookup
the section that the relo-section points to and check if it contains
executable machine instructions (denoted by the sh_flags
SHF_EXECINSTR). Use this check to also skip irrelevant relo-sections.
Note, for samples/bpf/ the '-target bpf' parameter to clang cannot be used
due to incompatibility with asm embedded headers, that some of the samples
include. This is explained in more details by Yonghong Song in bpf_devel_QA.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tang Junhui [Wed, 7 Feb 2018 19:41:45 +0000 (11:41 -0800)]
bcache: return attach error when no cache set exist
[ Upstream commit
7f4fc93d4713394ee8f1cd44c238e046e11b4f15 ]
I attach a back-end device to a cache set, and the cache set is not
registered yet, this back-end device did not attach successfully, and no
error returned:
[root]# echo
87859280-fec6-4bcc-
20df7ca8f86b > /sys/block/sde/bcache/attach
[root]#
In sysfs_attach(), the return value "v" is initialized to "size" in
the beginning, and if no cache set exist in bch_cache_sets, the "v" value
would not change any more, and return to sysfs, sysfs regard it as success
since the "size" is a positive number.
This patch fixes this issue by assigning "v" with "-ENOENT" in the
initialization.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tang Junhui [Wed, 7 Feb 2018 19:41:46 +0000 (11:41 -0800)]
bcache: fix for data collapse after re-attaching an attached device
[ Upstream commit
73ac105be390c1de42a2f21643c9778a5e002930 ]
back-end device sdm has already attached a cache_set with ID
f67ebe1f-f8bc-4d73-bfe5-
9dc88607f119, then try to attach with
another cache set, and it returns with an error:
[root]# cd /sys/block/sdm/bcache
[root]# echo
5ccd0a63-148e-48b8-afa2-
aca9cbd6279f > attach
-bash: echo: write error: Invalid argument
After that, execute a command to modify the label of bcache
device:
[root]# echo data_disk1 > label
Then we reboot the system, when the system power on, the back-end
device can not attach to cache_set, a messages show in the log:
Feb 5 12:05:52 ceph152 kernel: [922385.508498] bcache:
bch_cached_dev_attach() couldn't find uuid for sdm in set
In sysfs_attach(), dc->sb.set_uuid was assigned to the value
which input through sysfs, no matter whether it is success
or not in bch_cached_dev_attach(). For example, If the back-end
device has already attached to an cache set, bch_cached_dev_attach()
would fail, but dc->sb.set_uuid was changed. Then modify the
label of bcache device, it will call bch_write_bdev_super(),
which would write the dc->sb.set_uuid to the super block, so we
record a wrong cache set ID in the super block, after the system
reboot, the cache set couldn't find the uuid of the back-end
device, so the bcache device couldn't exist and use any more.
In this patch, we don't assigned cache set ID to dc->sb.set_uuid
in sysfs_attach() directly, but input it into bch_cached_dev_attach(),
and assigned dc->sb.set_uuid to the cache set ID after the back-end
device attached to the cache set successful.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tang Junhui [Wed, 7 Feb 2018 19:41:43 +0000 (11:41 -0800)]
bcache: fix for allocator and register thread race
[ Upstream commit
682811b3ce1a5a4e20d700939a9042f01dbc66c4 ]
After long time running of random small IO writing,
I reboot the machine, and after the machine power on,
I found bcache got stuck, the stack is:
[root@ceph153 ~]# cat /proc/2510/task/*/stack
[<
ffffffffa06b2455>] closure_sync+0x25/0x90 [bcache]
[<
ffffffffa06b6be8>] bch_journal+0x118/0x2b0 [bcache]
[<
ffffffffa06b6dc7>] bch_journal_meta+0x47/0x70 [bcache]
[<
ffffffffa06be8f7>] bch_prio_write+0x237/0x340 [bcache]
[<
ffffffffa06a8018>] bch_allocator_thread+0x3c8/0x3d0 [bcache]
[<
ffffffff810a631f>] kthread+0xcf/0xe0
[<
ffffffff8164c318>] ret_from_fork+0x58/0x90
[<
ffffffffffffffff>] 0xffffffffffffffff
[root@ceph153 ~]# cat /proc/2038/task/*/stack
[<
ffffffffa06b1abd>] __bch_btree_map_nodes+0x12d/0x150 [bcache]
[<
ffffffffa06b1bd1>] bch_btree_insert+0xf1/0x170 [bcache]
[<
ffffffffa06b637f>] bch_journal_replay+0x13f/0x230 [bcache]
[<
ffffffffa06c75fe>] run_cache_set+0x79a/0x7c2 [bcache]
[<
ffffffffa06c0cf8>] register_bcache+0xd48/0x1310 [bcache]
[<
ffffffff812f702f>] kobj_attr_store+0xf/0x20
[<
ffffffff8125b216>] sysfs_write_file+0xc6/0x140
[<
ffffffff811dfbfd>] vfs_write+0xbd/0x1e0
[<
ffffffff811e069f>] SyS_write+0x7f/0xe0
[<
ffffffff8164c3c9>] system_call_fastpath+0x16/0x1
The stack shows the register thread and allocator thread
were getting stuck when registering cache device.
I reboot the machine several times, the issue always
exsit in this machine.
I debug the code, and found the call trace as bellow:
register_bcache()
==>run_cache_set()
==>bch_journal_replay()
==>bch_btree_insert()
==>__bch_btree_map_nodes()
==>btree_insert_fn()
==>btree_split() //node need split
==>btree_check_reserve()
In btree_check_reserve(), It will check if there is enough buckets
of RESERVE_BTREE type, since allocator thread did not work yet, so
no buckets of RESERVE_BTREE type allocated, so the register thread
waits on c->btree_cache_wait, and goes to sleep.
Then the allocator thread initialized, the call trace is bellow:
bch_allocator_thread()
==>bch_prio_write()
==>bch_journal_meta()
==>bch_journal()
==>journal_wait_for_write()
In journal_wait_for_write(), It will check if journal is full by
journal_full(), but the long time random small IO writing
causes the exhaustion of journal buckets(journal.blocks_free=0),
In order to release the journal buckets,
the allocator calls btree_flush_write() to flush keys to
btree nodes, and waits on c->journal.wait until btree nodes writing
over or there has already some journal buckets space, then the
allocator thread goes to sleep. but in btree_flush_write(), since
bch_journal_replay() is not finished, so no btree nodes have journal
(condition "if (btree_current_write(b)->journal)" never satisfied),
so we got no btree node to flush, no journal bucket released,
and allocator sleep all the times.
Through the above analysis, we can see that:
1) Register thread wait for allocator thread to allocate buckets of
RESERVE_BTREE type;
2) Alloctor thread wait for register thread to replay journal, so it
can flush btree nodes and get journal bucket.
then they are all got stuck by waiting for each other.
Hua Rui provided a patch for me, by allocating some buckets of
RESERVE_BTREE type in advance, so the register thread can get bucket
when btree node splitting and no need to waiting for the allocator
thread. I tested it, it has effect, and register thread run a step
forward, but finally are still got stuck, the reason is only 8 bucket
of RESERVE_BTREE type were allocated, and in bch_journal_replay(),
after 2 btree nodes splitting, only 4 bucket of RESERVE_BTREE type left,
then btree_check_reserve() is not satisfied anymore, so it goes to sleep
again, and in the same time, alloctor thread did not flush enough btree
nodes to release a journal bucket, so they all got stuck again.
So we need to allocate more buckets of RESERVE_BTREE type in advance,
but how much is enough? By experience and test, I think it should be
as much as journal buckets. Then I modify the code as this patch,
and test in the machine, and it works.
This patch modified base on Hua Rui’s patch, and allocate more buckets
of RESERVE_BTREE type in advance to avoid register thread and allocate
thread going to wait for each other.
[patch v2] ca->sb.njournal_buckets would be 0 in the first time after
cache creation, and no journal exists, so just 8 btree buckets is OK.
Signed-off-by: Hua Rui <huarui.dev@gmail.com>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coly Li [Wed, 7 Feb 2018 19:41:41 +0000 (11:41 -0800)]
bcache: properly set task state in bch_writeback_thread()
[ Upstream commit
99361bbf26337186f02561109c17a4c4b1a7536a ]
Kernel thread routine bch_writeback_thread() has the following code block,
447 down_write(&dc->writeback_lock);
448~450 if (check conditions) {
451 up_write(&dc->writeback_lock);
452 set_current_state(TASK_INTERRUPTIBLE);
453
454 if (kthread_should_stop())
455 return 0;
456
457 schedule();
458 continue;
459 }
If condition check is true, its task state is set to TASK_INTERRUPTIBLE
and call schedule() to wait for others to wake up it.
There are 2 issues in current code,
1, Task state is set to TASK_INTERRUPTIBLE after the condition checks, if
another process changes the condition and call wake_up_process(dc->
writeback_thread), then at line 452 task state is set back to
TASK_INTERRUPTIBLE, the writeback kernel thread will lose a chance to be
waken up.
2, At line 454 if kthread_should_stop() is true, writeback kernel thread
will return to kernel/kthread.c:kthread() with TASK_INTERRUPTIBLE and
call do_exit(). It is not good to enter do_exit() with task state
TASK_INTERRUPTIBLE, in following code path might_sleep() is called and a
warning message is reported by __might_sleep(): "WARNING: do not call
blocking ops when !TASK_RUNNING; state=1 set at [xxxx]".
For the first issue, task state should be set before condition checks.
Ineed because dc->writeback_lock is required when modifying all the
conditions, calling set_current_state() inside code block where dc->
writeback_lock is hold is safe. But this is quite implicit, so I still move
set_current_state() before all the condition checks.
For the second issue, frankley speaking it does not hurt when kernel thread
exits with TASK_INTERRUPTIBLE state, but this warning message scares users,
makes them feel there might be something risky with bcache and hurt their
data. Setting task state to TASK_RUNNING before returning fixes this
problem.
In alloc.c:allocator_wait(), there is also a similar issue, and is also
fixed in this patch.
Changelog:
v3: merge two similar fixes into one patch
v2: fix the race issue in v1 patch.
v1: initial buggy fix.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Cc: Michael Lyle <mlyle@lyle.org>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Fri, 2 Feb 2018 15:48:47 +0000 (16:48 +0100)]
cifs: silence compiler warnings showing up with gcc-8.0.0
[ Upstream commit
ade7db991b47ab3016a414468164f4966bd08202 ]
This bug was fixed before, but came up again with the latest
compiler in another function:
fs/cifs/cifssmb.c: In function 'CIFSSMBSetEA':
fs/cifs/cifssmb.c:6362:3: error: 'strncpy' offset 8 is out of the bounds [0, 4] [-Werror=array-bounds]
strncpy(parm_data->list[0].name, ea_name, name_len);
Let's apply the same fix that was used for the other instances.
Fixes:
b2a3ad9ca502 ("cifs: silence compiler warnings showing up with gcc-4.7.0")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Dobriyan [Tue, 6 Feb 2018 23:36:59 +0000 (15:36 -0800)]
proc: fix /proc/*/map_files lookup
[ Upstream commit
ac7f1061c2c11bb8936b1b6a94cdb48de732f7a4 ]
Current code does:
if (sscanf(dentry->d_name.name, "%lx-%lx", start, end) != 2)
However sscanf() is broken garbage.
It silently accepts whitespace between format specifiers
(did you know that?).
It silently accepts valid strings which result in integer overflow.
Do not use sscanf() for any even remotely reliable parsing code.
OK
# readlink '/proc/1/map_files/
55a23af39000-
55a23b05b000'
/lib/systemd/systemd
broken
# readlink '/proc/1/map_files/
55a23af39000-
55a23b05b000'
/lib/systemd/systemd
broken
# readlink '/proc/1/map_files/
55a23af39000-
55a23b05b000 '
/lib/systemd/systemd
very broken
# readlink '/proc/1/map_files/
1000000000000000055a23af39000-
55a23b05b000'
/lib/systemd/systemd
Andrei said:
: This patch breaks criu. It was a bug in criu. And this bug is on a minor
: path, which works when memfd_create() isn't available. It is a reason why
: I ask to not backport this patch to stable kernels.
:
: In CRIU this bug can be triggered, only if this patch will be backported
: to a kernel which version is lower than v3.16.
Link: http://lkml.kernel.org/r/20171120212706.GA14325@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Wed, 31 Jan 2018 12:12:20 +0000 (12:12 +0000)]
arm64: spinlock: Fix theoretical trylock() A-B-A with LSE atomics
[ Upstream commit
202fb4ef81e3ec765c23bd1e6746a5c25b797d0e ]
If the spinlock "next" ticket wraps around between the initial LDR
and the cmpxchg in the LSE version of spin_trylock, then we can erroneously
think that we have successfuly acquired the lock because we only check
whether the next ticket return by the cmpxchg is equal to the owner ticket
in our updated lock word.
This patch fixes the issue by performing a full 32-bit check of the lock
word when trying to determine whether or not the CASA instruction updated
memory.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guanglei Li [Tue, 6 Feb 2018 02:43:21 +0000 (10:43 +0800)]
RDS: IB: Fix null pointer issue
[ Upstream commit
2c0aa08631b86a4678dbc93b9caa5248014b4458 ]
Scenario:
1. Port down and do fail over
2. Ap do rds_bind syscall
PID: 47039 TASK:
ffff89887e2fe640 CPU: 47 COMMAND: "kworker/u:6"
#0 [
ffff898e35f159f0] machine_kexec at
ffffffff8103abf9
#1 [
ffff898e35f15a60] crash_kexec at
ffffffff810b96e3
#2 [
ffff898e35f15b30] oops_end at
ffffffff8150f518
#3 [
ffff898e35f15b60] no_context at
ffffffff8104854c
#4 [
ffff898e35f15ba0] __bad_area_nosemaphore at
ffffffff81048675
#5 [
ffff898e35f15bf0] bad_area_nosemaphore at
ffffffff810487d3
#6 [
ffff898e35f15c00] do_page_fault at
ffffffff815120b8
#7 [
ffff898e35f15d10] page_fault at
ffffffff8150ea95
[exception RIP: unknown or invalid address]
RIP:
0000000000000000 RSP:
ffff898e35f15dc8 RFLAGS:
00010282
RAX:
00000000fffffffe RBX:
ffff889b77f6fc00 RCX:
ffffffff81c99d88
RDX:
0000000000000000 RSI:
ffff896019ee08e8 RDI:
ffff889b77f6fc00
RBP:
ffff898e35f15df0 R8:
ffff896019ee08c8 R9:
0000000000000000
R10:
0000000000000400 R11:
0000000000000000 R12:
ffff896019ee08c0
R13:
ffff889b77f6fe68 R14:
ffffffff81c99d80 R15:
ffffffffa022a1e0
ORIG_RAX:
ffffffffffffffff CS: 0010 SS: 0018
#8 [
ffff898e35f15dc8] cma_ndev_work_handler at
ffffffffa022a228 [rdma_cm]
#9 [
ffff898e35f15df8] process_one_work at
ffffffff8108a7c6
#10 [
ffff898e35f15e58] worker_thread at
ffffffff8108bda0
#11 [
ffff898e35f15ee8] kthread at
ffffffff81090fe6
PID: 45659 TASK:
ffff880d313d2500 CPU: 31 COMMAND: "oracle_45659_ap"
#0 [
ffff881024ccfc98] __schedule at
ffffffff8150bac4
#1 [
ffff881024ccfd40] schedule at
ffffffff8150c2cf
#2 [
ffff881024ccfd50] __mutex_lock_slowpath at
ffffffff8150cee7
#3 [
ffff881024ccfdc0] mutex_lock at
ffffffff8150cdeb
#4 [
ffff881024ccfde0] rdma_destroy_id at
ffffffffa022a027 [rdma_cm]
#5 [
ffff881024ccfe10] rds_ib_laddr_check at
ffffffffa0357857 [rds_rdma]
#6 [
ffff881024ccfe50] rds_trans_get_preferred at
ffffffffa0324c2a [rds]
#7 [
ffff881024ccfe80] rds_bind at
ffffffffa031d690 [rds]
#8 [
ffff881024ccfeb0] sys_bind at
ffffffff8142a670
PID: 45659 PID: 47039
rds_ib_laddr_check
/* create id_priv with a null event_handler */
rdma_create_id
rdma_bind_addr
cma_acquire_dev
/* add id_priv to cma_dev->id_list */
cma_attach_to_dev
cma_ndev_work_handler
/* event_hanlder is null */
id_priv->id.event_handler
Signed-off-by: Guanglei Li <guanglei.li@oracle.com>
Signed-off-by: Honglei Wang <honglei.wang@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Yanjun Zhu <yanjun.zhu@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ross Lagerwall [Thu, 11 Jan 2018 09:36:37 +0000 (09:36 +0000)]
xen/grant-table: Use put_page instead of free_page
[ Upstream commit
3ac7292a25db1c607a50752055a18aba32ac2176 ]
The page given to gnttab_end_foreign_access() to free could be a
compound page so use put_page() instead of free_page() since it can
handle both compound and single pages correctly.
This bug was discovered when migrating a Xen VM with several VIFs and
CONFIG_DEBUG_VM enabled. It hits a BUG usually after fewer than 10
iterations. All netfront devices disconnect from the backend during a
suspend/resume and this will call gnttab_end_foreign_access() if a
netfront queue has an outstanding skb. The mismatch between calling
get_page() and free_page() on a compound page causes a reference
counting error which is detected when DEBUG_VM is enabled.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ross Lagerwall [Thu, 11 Jan 2018 09:36:38 +0000 (09:36 +0000)]
xen-netfront: Fix race between device setup and open
[ Upstream commit
f599c64fdf7d9c108e8717fb04bc41c680120da4 ]
When a netfront device is set up it registers a netdev fairly early on,
before it has set up the queues and is actually usable. A userspace tool
like NetworkManager will immediately try to open it and access its state
as soon as it appears. The bug can be reproduced by hotplugging VIFs
until the VM runs out of grant refs. It registers the netdev but fails
to set up any queues (since there are no more grant refs). In the
meantime, NetworkManager opens the device and the kernel crashes trying
to access the queues (of which there are none).
Fix this in two ways:
* For initial setup, register the netdev much later, after the queues
are setup. This avoids the race entirely.
* During a suspend/resume cycle, the frontend reconnects to the backend
and the queues are recreated. It is possible (though highly unlikely) to
race with something opening the device and accessing the queues after
they have been destroyed but before they have been recreated. Extend the
region covered by the rtnl semaphore to protect against this race. There
is a possibility that we fail to recreate the queues so check for this
in the open function.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matt Redfearn [Mon, 29 Jan 2018 11:26:45 +0000 (11:26 +0000)]
MIPS: TXx9: use IS_BUILTIN() for CONFIG_LEDS_CLASS
[ Upstream commit
0cde5b44a30f1daaef1c34e08191239dc63271c4 ]
When commit
b27311e1cace ("MIPS: TXx9: Add RBTX4939 board support")
added board support for the RBTX4939, it added a call to
led_classdev_register even if the LED class is built as a module.
Built-in arch code cannot call module code directly like this. Commit
b33b44073734 ("MIPS: TXX9: use IS_ENABLED() macro") subsequently
changed the inclusion of this code to a single check that
CONFIG_LEDS_CLASS is either builtin or a module, but the same issue
remains.
This leads to MIPS allmodconfig builds failing when CONFIG_MACH_TX49XX=y
is set:
arch/mips/txx9/rbtx4939/setup.o: In function `rbtx4939_led_probe':
setup.c:(.init.text+0xc0): undefined reference to `of_led_classdev_register'
make: *** [Makefile:999: vmlinux] Error 1
Fix this by using the IS_BUILTIN() macro instead.
Fixes:
b27311e1cace ("MIPS: TXx9: Add RBTX4939 board support")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18544/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Hogan [Fri, 2 Feb 2018 22:14:09 +0000 (22:14 +0000)]
MIPS: generic: Fix machine compatible matching
[ Upstream commit
9a9ab3078e2744a1a55163cfaec73a5798aae33e ]
We now have a platform (Ranchu) in the "generic" platform which matches
based on the FDT compatible string using mips_machine_is_compatible(),
however that function doesn't stop at a blank struct
of_device_id::compatible as that is an array in the struct, not a
pointer to a string.
Fix the loop completion to check the first byte of the compatible array
rather than the address of the compatible array in the struct.
Fixes:
eed0eabd12ef ("MIPS: generic: Introduce generic DT-based board support")
Signed-off-by: James Hogan <jhogan@kernel.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18580/
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yonghong Song [Sat, 3 Feb 2018 06:37:15 +0000 (22:37 -0800)]
bpf: fix selftests/bpf test_kmod.sh failure when CONFIG_BPF_JIT_ALWAYS_ON=y
[ Upstream commit
09584b406742413ac4c8d7e030374d4daa045b69 ]
With CONFIG_BPF_JIT_ALWAYS_ON is defined in the config file,
tools/testing/selftests/bpf/test_kmod.sh failed like below:
[root@localhost bpf]# ./test_kmod.sh
sysctl: setting key "net.core.bpf_jit_enable": Invalid argument
[ JIT enabled:0 hardened:0 ]
[ 132.175681] test_bpf: #297 BPF_MAXINSNS: Jump, gap, jump, ... FAIL to prog_create err=-524 len=4096
[ 132.458834] test_bpf: Summary: 348 PASSED, 1 FAILED, [340/340 JIT'ed]
[ JIT enabled:1 hardened:0 ]
[ 133.456025] test_bpf: #297 BPF_MAXINSNS: Jump, gap, jump, ... FAIL to prog_create err=-524 len=4096
[ 133.730935] test_bpf: Summary: 348 PASSED, 1 FAILED, [340/340 JIT'ed]
[ JIT enabled:1 hardened:1 ]
[ 134.769730] test_bpf: #297 BPF_MAXINSNS: Jump, gap, jump, ... FAIL to prog_create err=-524 len=4096
[ 135.050864] test_bpf: Summary: 348 PASSED, 1 FAILED, [340/340 JIT'ed]
[ JIT enabled:1 hardened:2 ]
[ 136.442882] test_bpf: #297 BPF_MAXINSNS: Jump, gap, jump, ... FAIL to prog_create err=-524 len=4096
[ 136.821810] test_bpf: Summary: 348 PASSED, 1 FAILED, [340/340 JIT'ed]
[root@localhost bpf]#
The test_kmod.sh load/remove test_bpf.ko multiple times with different
settings for sysctl net.core.bpf_jit_{enable,harden}. The failed test #297
of test_bpf.ko is designed such that JIT always fails.
Commit
290af86629b2 (bpf: introduce BPF_JIT_ALWAYS_ON config)
introduced the following tightening logic:
...
if (!bpf_prog_is_dev_bound(fp->aux)) {
fp = bpf_int_jit_compile(fp);
#ifdef CONFIG_BPF_JIT_ALWAYS_ON
if (!fp->jited) {
*err = -ENOTSUPP;
return fp;
}
#endif
...
With this logic, Test #297 always gets return value -ENOTSUPP
when CONFIG_BPF_JIT_ALWAYS_ON is defined, causing the test failure.
This patch fixed the failure by marking Test #297 as expected failure
when CONFIG_BPF_JIT_ALWAYS_ON is defined.
Fixes:
290af86629b2 (bpf: introduce BPF_JIT_ALWAYS_ON config)
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Fri, 26 Jan 2018 15:02:59 +0000 (16:02 +0100)]
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
[ Upstream commit
63347db0affadcbccd5613116ea8431c70139b3e ]
The acpi_get_bus_status wrapper for acpi_bus_get_status_handle has some
code to handle certain device quirks, in some cases we also need this
quirk handling for the initial _STA call.
Specifically on some devices calling _STA before all _DEP dependencies
are met results in errors like these:
[ 0.123579] ACPI Error: No handler for Region [ECRM] (
00000000ba9edc4c)
[GenericSerialBus] (
20170831/evregion-166)
[ 0.123601] ACPI Error: Region GenericSerialBus (ID=9) has no handler
(
20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (
20170831/psparse-550)
acpi_get_bus_status already has code to avoid this, so by using it we
also silence these errors from the initial _STA call.
Note that in order for the acpi_get_bus_status handling for this to work,
we initialize dep_unmet to 1 until acpi_device_dep_initialize gets called,
this means that battery devices will be instantiated with an initial
status of 0. This is not a problem, acpi_bus_attach will get called soon
after the instantiation anyways and it will update the status as first
point of order.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen Yu [Mon, 29 Jan 2018 02:26:46 +0000 (10:26 +0800)]
ACPI: processor_perflib: Do not send _PPC change notification if not ready
[ Upstream commit
ba1edb9a5125a617d612f98eead14b9b84e75c3a ]
The following warning was triggered after resumed from S3 -
if all the nonboot CPUs were put offline before suspend:
[ 1840.329515] unchecked MSR access error: RDMSR from 0x771 at rIP: 0xffffffff86061e3a (native_read_msr+0xa/0x30)
[ 1840.329516] Call Trace:
[ 1840.329521] __rdmsr_on_cpu+0x33/0x50
[ 1840.329525] generic_exec_single+0x81/0xb0
[ 1840.329527] smp_call_function_single+0xd2/0x100
[ 1840.329530] ? acpi_ds_result_pop+0xdd/0xf2
[ 1840.329532] ? acpi_ds_create_operand+0x215/0x23c
[ 1840.329534] rdmsrl_on_cpu+0x57/0x80
[ 1840.329536] ? cpumask_next+0x1b/0x20
[ 1840.329538] ? rdmsrl_on_cpu+0x57/0x80
[ 1840.329541] intel_pstate_update_perf_limits+0xf3/0x220
[ 1840.329544] ? notifier_call_chain+0x4a/0x70
[ 1840.329546] intel_pstate_set_policy+0x4e/0x150
[ 1840.329548] cpufreq_set_policy+0xcd/0x2f0
[ 1840.329550] cpufreq_update_policy+0xb2/0x130
[ 1840.329552] ? cpufreq_update_policy+0x130/0x130
[ 1840.329556] acpi_processor_ppc_has_changed+0x65/0x80
[ 1840.329558] acpi_processor_notify+0x80/0x100
[ 1840.329561] acpi_ev_notify_dispatch+0x44/0x5c
[ 1840.329563] acpi_os_execute_deferred+0x14/0x20
[ 1840.329565] process_one_work+0x193/0x3c0
[ 1840.329567] worker_thread+0x35/0x3b0
[ 1840.329569] kthread+0x125/0x140
[ 1840.329571] ? process_one_work+0x3c0/0x3c0
[ 1840.329572] ? kthread_park+0x60/0x60
[ 1840.329575] ? do_syscall_64+0x67/0x180
[ 1840.329577] ret_from_fork+0x25/0x30
[ 1840.329585] unchecked MSR access error: WRMSR to 0x774 (tried to write 0x0000000000000000) at rIP: 0xffffffff86061f78 (native_write_msr+0x8/0x30)
[ 1840.329586] Call Trace:
[ 1840.329587] __wrmsr_on_cpu+0x37/0x40
[ 1840.329589] generic_exec_single+0x81/0xb0
[ 1840.329592] smp_call_function_single+0xd2/0x100
[ 1840.329594] ? acpi_ds_create_operand+0x215/0x23c
[ 1840.329595] ? cpumask_next+0x1b/0x20
[ 1840.329597] wrmsrl_on_cpu+0x57/0x70
[ 1840.329598] ? rdmsrl_on_cpu+0x57/0x80
[ 1840.329599] ? wrmsrl_on_cpu+0x57/0x70
[ 1840.329602] intel_pstate_hwp_set+0xd3/0x150
[ 1840.329604] intel_pstate_set_policy+0x119/0x150
[ 1840.329606] cpufreq_set_policy+0xcd/0x2f0
[ 1840.329607] cpufreq_update_policy+0xb2/0x130
[ 1840.329610] ? cpufreq_update_policy+0x130/0x130
[ 1840.329613] acpi_processor_ppc_has_changed+0x65/0x80
[ 1840.329615] acpi_processor_notify+0x80/0x100
[ 1840.329617] acpi_ev_notify_dispatch+0x44/0x5c
[ 1840.329619] acpi_os_execute_deferred+0x14/0x20
[ 1840.329620] process_one_work+0x193/0x3c0
[ 1840.329622] worker_thread+0x35/0x3b0
[ 1840.329624] kthread+0x125/0x140
[ 1840.329625] ? process_one_work+0x3c0/0x3c0
[ 1840.329626] ? kthread_park+0x60/0x60
[ 1840.329628] ? do_syscall_64+0x67/0x180
[ 1840.329631] ret_from_fork+0x25/0x30
This is because if there's only one online CPU, the MSR_PM_ENABLE
(package wide)can not be enabled after resumed, due to
intel_pstate_hwp_enable() will only be invoked on AP's online
process after resumed - if there's no AP online, the HWP remains
disabled after resumed (BIOS has disabled it in S3). Then if
there comes a _PPC change notification which touches HWP register
during this stage, the warning is triggered.
Since we don't call acpi_processor_register_performance() when
HWP is enabled, the pr->performance will be NULL. When this is
NULL we don't need to do _PPC change notification.
Reported-by: Doug Smythies <dsmythies@telus.net>
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Yu Chen <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean Delvare [Sat, 3 Feb 2018 10:25:20 +0000 (11:25 +0100)]
firmware: dmi_scan: Fix handling of empty DMI strings
[ Upstream commit
a7770ae194569e96a93c48aceb304edded9cc648 ]
The handling of empty DMI strings looks quite broken to me:
* Strings from 1 to 7 spaces are not considered empty.
* True empty DMI strings (string index set to 0) are not considered
empty, and result in allocating a 0-char string.
* Strings with invalid index also result in allocating a 0-char
string.
* Strings starting with 8 spaces are all considered empty, even if
non-space characters follow (sounds like a weird thing to do, but
I have actually seen occurrences of this in DMI tables before.)
* Strings which are considered empty are reported as 8 spaces,
instead of being actually empty.
Some of these issues are the result of an off-by-one error in memcmp,
the rest is incorrect by design.
So let's get it square: missing strings and strings made of only
spaces, regardless of their length, should be treated as empty and
no memory should be allocated for them. All other strings are
non-empty and should be allocated.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes:
79da4721117f ("x86: fix DMI out of memory problems")
Cc: Parag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Fri, 2 Feb 2018 14:56:18 +0000 (15:56 +0100)]
x86/power: Fix swsusp_arch_resume prototype
[ Upstream commit
328008a72d38b5bde6491e463405c34a81a65d3e ]
The declaration for swsusp_arch_resume marks it as 'asmlinkage', but the
definition in x86-32 does not, and it fails to include the header with the
declaration. This leads to a warning when building with
link-time-optimizations:
kernel/power/power.h:108:23: error: type of 'swsusp_arch_resume' does not match original declaration [-Werror=lto-type-mismatch]
extern asmlinkage int swsusp_arch_resume(void);
^
arch/x86/power/hibernate_32.c:148:0: note: 'swsusp_arch_resume' was previously declared here
int swsusp_arch_resume(void)
This moves the declaration into a globally visible header file and fixes up
both x86 definitions to match it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Link: https://lkml.kernel.org/r/20180202145634.200291-2-arnd@arndb.de
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subash Abhinov Kasiviswanathan [Wed, 31 Jan 2018 11:50:01 +0000 (04:50 -0700)]
netfilter: ipv6: nf_defrag: Kill frag queue on RFC2460 failure
[ Upstream commit
ea23d5e3bf340e413b8e05c13da233c99c64142b ]
Failures were seen in ICMPv6 fragmentation timeout tests if they were
run after the RFC2460 failure tests. Kernel was not sending out the
ICMPv6 fragment reassembly time exceeded packet after the fragmentation
reassembly timeout of 1 minute had elapsed.
This happened because the frag queue was not released if an error in
IPv6 fragmentation header was detected by RFC2460.
Fixes:
83f1999caeb1 ("netfilter: ipv6: nf_defrag: Pass on packets to stack per RFC2460")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Karol Herbst [Mon, 6 Nov 2017 15:32:41 +0000 (16:32 +0100)]
drm/nouveau/pmu/fuc: don't use movw directly anymore
[ Upstream commit
fe9748b7b41cee11f8db57fb8b20bc540a33102a ]
Fixes failure to compile with recent envyas as a result of the 'movw'
alias being removed for v5.
A bit of history:
v3 only has a 16-bit sign-extended immediate mov op. In order to set
the high bits, there's a separate 'sethi' op. envyas validates that
the value passed to mov(imm) is between -0x8000 and 0x7fff. In order
to simplify macros that load both the low and high word, a 'movw'
alias was added which takes an unsigned 16-bit immediate. However the
actual hardware op still sign extends.
v5 has a full 32-bit immediate mov op. The v3 16-bit immediate mov op
is gone (loads 0 into the dst reg). However due to a bug in envyas,
the movw alias still existed, and selected the no-longer-present v3
16-bit immediate mov op. As a result usage of movw on v5 is the same
as mov with a 0x0 argument.
The proper fix throughout is to only ever use the 'movw' alias in
combination with 'sethi'. Anything else should get the sign-extended
validation to ensure that the intended value ends up in the
destination register.
Changes in fuc3 binaries is the result of a different encoding being
selected for a mov with an 8-bit value.
v2: added commit message written by Ilia, thanks for that!
v3: messed up rebasing, now it should apply
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Estrin [Thu, 1 Feb 2018 18:55:41 +0000 (10:55 -0800)]
IB/ipoib: Fix for potential no-carrier state
[ Upstream commit
1029361084d18cc270f64dfd39529fafa10cfe01 ]
On reboot SM can program port pkey table before ipoib registered its
event handler, which could result in missing pkey event and leave root
interface with initial pkey value from index 0.
Since OPA port starts with invalid pkey in index 0, root interface will
fail to initialize and stay down with no-carrier flag.
For IB ipoib interface may end up with pkey different from value
opensm put in pkey table idx 0, resulting in connectivity issues
(different mcast groups, for example).
Close the window by calling event handler after registration
to make sure ipoib pkey is in sync with port pkey table.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ed Swierk [Thu, 1 Feb 2018 02:48:02 +0000 (18:48 -0800)]
openvswitch: Remove padding from packet before L3+ conntrack processing
[ Upstream commit
9382fe71c0058465e942a633869629929102843d ]
IPv4 and IPv6 packets may arrive with lower-layer padding that is not
included in the L3 length. For example, a short IPv4 packet may have
up to 6 bytes of padding following the IP payload when received on an
Ethernet device with a minimum packet length of 64 bytes.
Higher-layer processing functions in netfilter (e.g. nf_ip_checksum(),
and help() in nf_conntrack_ftp) assume skb->len reflects the length of
the L3 header and payload, rather than referring back to
ip_hdr->tot_len or ipv6_hdr->payload_len, and get confused by
lower-layer padding.
In the normal IPv4 receive path, ip_rcv() trims the packet to
ip_hdr->tot_len before invoking netfilter hooks. In the IPv6 receive
path, ip6_rcv() does the same using ipv6_hdr->payload_len. Similarly
in the br_netfilter receive path, br_validate_ipv4() and
br_validate_ipv6() trim the packet to the L3 length before invoking
netfilter hooks.
Currently in the OVS conntrack receive path, ovs_ct_execute() pulls
the skb to the L3 header but does not trim it to the L3 length before
calling nf_conntrack_in(NF_INET_PRE_ROUTING). When
nf_conntrack_proto_tcp encounters a packet with lower-layer padding,
nf_ip_checksum() fails causing a "nf_ct_tcp: bad TCP checksum" log
message. While extra zero bytes don't affect the checksum, the length
in the IP pseudoheader does. That length is based on skb->len, and
without trimming, it doesn't match the length the sender used when
computing the checksum.
In ovs_ct_execute(), trim the skb to the L3 length before higher-layer
processing.
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
shidao.ytt [Thu, 1 Feb 2018 00:19:55 +0000 (16:19 -0800)]
mm/fadvise: discard partial page if endbyte is also EOF
[ Upstream commit
a7ab400d6fe73d0119fdc234e9982a6f80faea9f ]
During our recent testing with fadvise(FADV_DONTNEED), we find that if
given offset/length is not page-aligned, the last page will not be
discarded. The tool we use is vmtouch (https://hoytech.com/vmtouch/),
we map a 10KB-sized file into memory and then try to run this tool to
evict the whole file mapping, but the last single page always remains
staying in the memory:
$./vmtouch -e test_10K
Files: 1
Directories: 0
Evicted Pages: 3 (12K)
Elapsed: 2.1e-05 seconds
$./vmtouch test_10K
Files: 1
Directories: 0
Resident Pages: 1/3 4K/12K 33.3%
Elapsed: 5.5e-05 seconds
However when we test with an older kernel, say 3.10, this problem is
gone. So we wonder if this is a regression:
$./vmtouch -e test_10K
Files: 1
Directories: 0
Evicted Pages: 3 (12K)
Elapsed: 8.2e-05 seconds
$./vmtouch test_10K
Files: 1
Directories: 0
Resident Pages: 0/3 0/12K 0% <-- partial page also discarded
Elapsed: 5e-05 seconds
After digging a little bit into this problem, we find it seems not a
regression. Not discarding partial page is likely to be on purpose
according to commit
441c228f817f ("mm: fadvise: document the
fadvise(FADV_DONTNEED) behaviour for partial pages") written by Mel
Gorman. He explained why partial pages should be preserved instead of
being discarded when using fadvise(FADV_DONTNEED).
However, the interesting part is that the actual code did NOT work as
the same as it was described, the partial page was still discarded
anyway, due to a calculation mistake of `end_index' passed to
invalidate_mapping_pages(). This mistake has not been fixed until
recently, that's why we fail to reproduce our problem in old kernels.
The fix is done in commit
18aba41cbf ("mm/fadvise.c: do not discard
partial pages with POSIX_FADV_DONTNEED") by Oleg Drokin.
Back to the original testing, our problem becomes that there is a
special case that, if the page-unaligned `endbyte' is also the end of
file, it is not necessary at all to preserve the last partial page, as
we all know no one else will use the rest of it. It should be safe
enough if we just discard the whole page. So we add an EOF check in
this patch.
We also find a poosbile real world issue in mainline kernel. Assume
such scenario: A userspace backup application want to backup a huge
amount of small files (<4k) at once, the developer might (I guess) want
to use fadvise(FADV_DONTNEED) to save memory. However, FADV_DONTNEED
won't really happen since the only page mapped is a partial page, and
kernel will preserve it. Our patch also fixes this problem, since we
know the endbyte is EOF, so we discard it.
Here is a simple reproducer to reproduce and verify each scenario we
described above:
test_fadvise.c
==============================
#include <sys/mman.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <stdlib.h>
#include <string.h>
#include <stdio.h>
#include <unistd.h>
int main(int argc, char **argv)
{
int i, fd, ret, len;
struct stat buf;
void *addr;
unsigned char *vec;
char *strbuf;
ssize_t pagesize = getpagesize();
ssize_t filesize;
fd = open(argv[1], O_RDWR|O_CREAT, S_IRUSR|S_IWUSR);
if (fd < 0)
return -1;
filesize = strtoul(argv[2], NULL, 10);
strbuf = malloc(filesize);
memset(strbuf, 42, filesize);
write(fd, strbuf, filesize);
free(strbuf);
fsync(fd);
len = (filesize + pagesize - 1) / pagesize;
printf("length of pages: %d\n", len);
addr = mmap(NULL, filesize, PROT_READ, MAP_SHARED, fd, 0);
if (addr == MAP_FAILED)
return -1;
ret = posix_fadvise(fd, 0, filesize, POSIX_FADV_DONTNEED);
if (ret < 0)
return -1;
vec = malloc(len);
ret = mincore(addr, filesize, (void *)vec);
if (ret < 0)
return -1;
for (i = 0; i < len; i++)
printf("pages[%d]: %x\n", i, vec[i] & 0x1);
free(vec);
close(fd);
return 0;
}
==============================
Test 1: running on kernel with commit
18aba41cbf reverted:
[root@caspar ~]# uname -r
4.15.0-rc6.revert+
[root@caspar ~]# ./test_fadvise file1 1024
length of pages: 1
pages[0]: 0 # <-- partial page discarded
[root@caspar ~]# ./test_fadvise file2 8192
length of pages: 2
pages[0]: 0
pages[1]: 0
[root@caspar ~]# ./test_fadvise file3 10240
length of pages: 3
pages[0]: 0
pages[1]: 0
pages[2]: 0 # <-- partial page discarded
Test 2: running on mainline kernel:
[root@caspar ~]# uname -r
4.15.0-rc6+
[root@caspar ~]# ./test_fadvise test1 1024
length of pages: 1
pages[0]: 1 # <-- partial and the only page not discarded
[root@caspar ~]# ./test_fadvise test2 8192
length of pages: 2
pages[0]: 0
pages[1]: 0
[root@caspar ~]# ./test_fadvise test3 10240
length of pages: 3
pages[0]: 0
pages[1]: 0
pages[2]: 1 # <-- partial page not discarded
Test 3: running on kernel with this patch:
[root@caspar ~]# uname -r
4.15.0-rc6.patched+
[root@caspar ~]# ./test_fadvise test1 1024
length of pages: 1
pages[0]: 0 # <-- partial page and EOF, discarded
[root@caspar ~]# ./test_fadvise test2 8192
length of pages: 2
pages[0]: 0
pages[1]: 0
[root@caspar ~]# ./test_fadvise test3 10240
length of pages: 3
pages[0]: 0
pages[1]: 0
pages[2]: 0 # <-- partial page and EOF, discarded
[akpm@linux-foundation.org: tweak code comment]
Link: http://lkml.kernel.org/r/5222da9ee20e1695eaabb69f631f200d6e6b8876.1515132470.git.jinli.zjl@alibaba-inc.com
Signed-off-by: shidao.ytt <shidao.ytt@alibaba-inc.com>
Signed-off-by: Caspar Zhang <jinli.zjl@alibaba-inc.com>
Reviewed-by: Oliver Yang <zhiche.yy@alibaba-inc.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mel Gorman [Thu, 1 Feb 2018 00:19:52 +0000 (16:19 -0800)]
mm: pin address_space before dereferencing it while isolating an LRU page
[ Upstream commit
69d763fc6d3aee787a3e8c8c35092b4f4960fa5d ]
Minchan Kim asked the following question -- what locks protects
address_space destroying when race happens between inode trauncation and
__isolate_lru_page? Jan Kara clarified by describing the race as follows
CPU1 CPU2
truncate(inode) __isolate_lru_page()
...
truncate_inode_page(mapping, page);
delete_from_page_cache(page)
spin_lock_irqsave(&mapping->tree_lock, flags);
__delete_from_page_cache(page, NULL)
page_cache_tree_delete(..)
... mapping = page_mapping(page);
page->mapping = NULL;
...
spin_unlock_irqrestore(&mapping->tree_lock, flags);
page_cache_free_page(mapping, page)
put_page(page)
if (put_page_testzero(page)) -> false
- inode now has no pages and can be freed including embedded address_space
if (mapping && !mapping->a_ops->migratepage)
- we've dereferenced mapping which is potentially already free.
The race is theoretically possible but unlikely. Before the
delete_from_page_cache, truncate_cleanup_page is called so the page is
likely to be !PageDirty or PageWriteback which gets skipped by the only
caller that checks the mappping in __isolate_lru_page. Even if the race
occurs, a substantial amount of work has to happen during a tiny window
with no preemption but it could potentially be done using a virtual
machine to artifically slow one CPU or halt it during the critical
window.
This patch should eliminate the race with truncation by try-locking the
page before derefencing mapping and aborting if the lock was not
acquired. There was a suggestion from Huang Ying to use RCU as a
side-effect to prevent mapping being freed. However, I do not like the
solution as it's an unconventional means of preserving a mapping and
it's not a context where rcu_read_lock is obviously protecting rcu data.
Link: http://lkml.kernel.org/r/20180104102512.2qos3h5vqzeisrek@techsingularity.net
Fixes:
c82449352854 ("mm: compaction: make isolate_lru_page() filter-aware again")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yang Shi [Thu, 1 Feb 2018 00:18:28 +0000 (16:18 -0800)]
mm: thp: use down_read_trylock() in khugepaged to avoid long block
[ Upstream commit
3b454ad35043dfbd3b5d2bb92b0991d6342afb44 ]
In the current design, khugepaged needs to acquire mmap_sem before
scanning an mm. But in some corner cases, khugepaged may scan a process
which is modifying its memory mapping, so khugepaged blocks in
uninterruptible state. But the process might hold the mmap_sem for a
long time when modifying a huge memory space and it may trigger the
below khugepaged hung issue:
INFO: task khugepaged:270 blocked for more than 120 seconds.
Tainted: G E 4.9.65-006.ali3000.alios7.x86_64 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
khugepaged D 0 270 2 0x00000000
ffff883f3deae4c0 0000000000000000 ffff883f610596c0 ffff883f7d359440
ffff883f63818000 ffffc90019adfc78 ffffffff817079a5 d67e5aa8c1860a64
0000000000000246 ffff883f7d359440 ffffc90019adfc88 ffff883f610596c0
Call Trace:
schedule+0x36/0x80
rwsem_down_read_failed+0xf0/0x150
call_rwsem_down_read_failed+0x18/0x30
down_read+0x20/0x40
khugepaged+0x476/0x11d0
kthread+0xe6/0x100
ret_from_fork+0x25/0x30
So it sounds pointless to just block khugepaged waiting for the
semaphore so replace down_read() with down_read_trylock() to move to
scan the next mm quickly instead of just blocking on the semaphore so
that other processes can get more chances to install THP. Then
khugepaged can come back to scan the skipped mm when it has finished the
current round full_scan.
And it appears that the change can improve khugepaged efficiency a
little bit.
Below is the test result when running LTP on a 24 cores 4GB memory 2
nodes NUMA VM:
pristine w/ trylock
full_scan 197 187
pages_collapsed 21 26
thp_fault_alloc 40818 44466
thp_fault_fallback 18413 16679
thp_collapse_alloc 21 150
thp_collapse_alloc_failed 14 16
thp_file_alloc 369 369
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: tweak comment]
[arnd@arndb.de: avoid uninitialized variable use]
Link: http://lkml.kernel.org/r/20171215125129.2948634-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1513281203-54878-1-git-send-email-yang.s@alibaba-inc.com
Signed-off-by: Yang Shi <yang.s@alibaba-inc.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nitin Gupta [Thu, 1 Feb 2018 00:18:09 +0000 (16:18 -0800)]
sparc64: update pmdp_invalidate() to return old pmd value
[ Upstream commit
a8e654f01cb725d0bfd741ebca1bf4c9337969cc ]
It's required to avoid losing dirty and accessed bits.
[akpm@linux-foundation.org: add a `do' to the do-while loop]
Link: http://lkml.kernel.org/r/20171213105756.69879-9-kirill.shutemov@linux.intel.com
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kirill A. Shutemov [Thu, 1 Feb 2018 00:17:43 +0000 (16:17 -0800)]
asm-generic: provide generic_pmdp_establish()
[ Upstream commit
c58f0bb77ed8bf93dfdde762b01cb67eebbdfc29 ]
Patch series "Do not lose dirty bit on THP pages", v4.
Vlastimil noted that pmdp_invalidate() is not atomic and we can lose
dirty and access bits if CPU sets them after pmdp dereference, but
before set_pmd_at().
The bug can lead to data loss, but the race window is tiny and I haven't
seen any reports that suggested that it happens in reality. So I don't
think it worth sending it to stable.
Unfortunately, there's no way to address the issue in a generic way. We
need to fix all architectures that support THP one-by-one.
All architectures that have THP supported have to provide atomic
pmdp_invalidate() that returns previous value.
If generic implementation of pmdp_invalidate() is used, architecture
needs to provide atomic pmdp_estabish().
pmdp_estabish() is not used out-side generic implementation of
pmdp_invalidate() so far, but I think this can change in the future.
This patch (of 12):
This is an implementation of pmdp_establish() that is only suitable for
an architecture that doesn't have hardware dirty/accessed bits. In this
case we can't race with CPU which sets these bits and non-atomic
approach is fine.
Link: http://lkml.kernel.org/r/20171213105756.69879-2-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Daney <david.daney@cavium.com>
Cc: David Miller <davem@davemloft.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nitin Gupta <nitin.m.gupta@oracle.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yisheng Xie [Thu, 1 Feb 2018 00:16:15 +0000 (16:16 -0800)]
mm/mempolicy: add nodes_empty check in SYSC_migrate_pages
[ Upstream commit
0486a38bcc4749808edbc848f1bcf232042770fc ]
As in manpage of migrate_pages, the errno should be set to EINVAL when
none of the node IDs specified by new_nodes are on-line and allowed by
the process's current cpuset context, or none of the specified nodes
contain memory. However, when test by following case:
new_nodes = 0;
old_nodes = 0xf;
ret = migrate_pages(pid, old_nodes, new_nodes, MAX);
The ret will be 0 and no errno is set. As the new_nodes is empty, we
should expect EINVAL as documented.
To fix the case like above, this patch check whether target nodes AND
current task_nodes is empty, and then check whether AND
node_states[N_MEMORY] is empty.
Link: http://lkml.kernel.org/r/1510882624-44342-4-git-send-email-xieyisheng1@huawei.com
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Chris Salls <salls@cs.ucsb.edu>
Cc: Christopher Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yisheng Xie [Thu, 1 Feb 2018 00:16:11 +0000 (16:16 -0800)]
mm/mempolicy: fix the check of nodemask from user
[ Upstream commit
56521e7a02b7b84a5e72691a1fb15570e6055545 ]
As Xiaojun reported the ltp of migrate_pages01 will fail on arm64 system
which has 4 nodes[0...3], all have memory and CONFIG_NODES_SHIFT=2:
migrate_pages01 0 TINFO : test_invalid_nodes
migrate_pages01 14 TFAIL : migrate_pages_common.c:45: unexpected failure - returned value = 0, expected: -1
migrate_pages01 15 TFAIL : migrate_pages_common.c:55: call succeeded unexpectedly
In this case the test_invalid_nodes of migrate_pages01 will call:
SYSC_migrate_pages as:
migrate_pages(0, , {0x0000000000000001}, 64, , {0x0000000000000010}, 64) = 0
The new nodes specifies one or more node IDs that are greater than the
maximum supported node ID, however, the errno is not set to EINVAL as
expected.
As man pages of set_mempolicy[1], mbind[2], and migrate_pages[3]
mentioned, when nodemask specifies one or more node IDs that are greater
than the maximum supported node ID, the errno should set to EINVAL.
However, get_nodes only check whether the part of bits
[BITS_PER_LONG*BITS_TO_LONGS(MAX_NUMNODES), maxnode) is zero or not, and
remain [MAX_NUMNODES, BITS_PER_LONG*BITS_TO_LONGS(MAX_NUMNODES)
unchecked.
This patch is to check the bits of [MAX_NUMNODES, maxnode) in get_nodes
to let migrate_pages set the errno to EINVAL when nodemask specifies one
or more node IDs that are greater than the maximum supported node ID,
which follows the manpage's guide.
[1] http://man7.org/linux/man-pages/man2/set_mempolicy.2.html
[2] http://man7.org/linux/man-pages/man2/mbind.2.html
[3] http://man7.org/linux/man-pages/man2/migrate_pages.2.html
Link: http://lkml.kernel.org/r/1510882624-44342-3-git-send-email-xieyisheng1@huawei.com
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Reported-by: Tan Xiaojun <tanxiaojun@huawei.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Chris Salls <salls@cs.ucsb.edu>
Cc: Christopher Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
piaojun [Thu, 1 Feb 2018 00:15:32 +0000 (16:15 -0800)]
ocfs2: return error when we attempt to access a dirty bh in jbd2
[ Upstream commit
d984187e3a1ad7d12447a7ab2c43ce3717a2b5b3 ]
We should not reuse the dirty bh in jbd2 directly due to the following
situation:
1. When removing extent rec, we will dirty the bhs of extent rec and
truncate log at the same time, and hand them over to jbd2.
2. The bhs are submitted to jbd2 area successfully.
3. The write-back thread of device help flush the bhs to disk but
encounter write error due to abnormal storage link.
4. After a while the storage link become normal. Truncate log flush
worker triggered by the next space reclaiming found the dirty bh of
truncate log and clear its 'BH_Write_EIO' and then set it uptodate in
__ocfs2_journal_access():
ocfs2_truncate_log_worker
ocfs2_flush_truncate_log
__ocfs2_flush_truncate_log
ocfs2_replay_truncate_records
ocfs2_journal_access_di
__ocfs2_journal_access // here we clear io_error and set 'tl_bh' uptodata.
5. Then jbd2 will flush the bh of truncate log to disk, but the bh of
extent rec is still in error state, and unfortunately nobody will
take care of it.
6. At last the space of extent rec was not reduced, but truncate log
flush worker have given it back to globalalloc. That will cause
duplicate cluster problem which could be identified by fsck.ocfs2.
Sadly we can hardly revert this but set fs read-only in case of ruining
atomicity and consistency of space reclaim.
Link: http://lkml.kernel.org/r/5A6E8092.8090701@huawei.com
Fixes:
acf8fdbe6afb ("ocfs2: do not BUG if buffer not uptodate in __ocfs2_journal_access")
Signed-off-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Reviewed-by: Changwei Ge <ge.changwei@h3c.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
piaojun [Thu, 1 Feb 2018 00:14:59 +0000 (16:14 -0800)]
ocfs2/acl: use 'ip_xattr_sem' to protect getting extended attribute
[ Upstream commit
16c8d569f5704a84164f30ff01b29879f3438065 ]
The race between *set_acl and *get_acl will cause getting incomplete
xattr data as below:
processA processB
ocfs2_set_acl
ocfs2_xattr_set
__ocfs2_xattr_set_handle
ocfs2_get_acl_nolock
ocfs2_xattr_get_nolock:
processB may get incomplete xattr data if processA hasn't set_acl done.
So we should use 'ip_xattr_sem' to protect getting extended attribute in
ocfs2_get_acl_nolock(), as other processes could be changing it
concurrently.
Link: http://lkml.kernel.org/r/5A5DDCFF.7030001@huawei.com
Signed-off-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Alex Chen <alex.chen@huawei.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
piaojun [Thu, 1 Feb 2018 00:14:44 +0000 (16:14 -0800)]
ocfs2: return -EROFS to mount.ocfs2 if inode block is invalid
[ Upstream commit
025bcbde3634b2c9b316f227fed13ad6ad6817fb ]
If metadata is corrupted such as 'invalid inode block', we will get
failed by calling 'mount()' and then set filesystem readonly as below:
ocfs2_mount
ocfs2_initialize_super
ocfs2_init_global_system_inodes
ocfs2_iget
ocfs2_read_locked_inode
ocfs2_validate_inode_block
ocfs2_error
ocfs2_handle_error
ocfs2_set_ro_flag(osb, 0); // set readonly
In this situation we need return -EROFS to 'mount.ocfs2', so that user
can fix it by fsck. And then mount again. In addition, 'mount.ocfs2'
should be updated correspondingly as it only return 1 for all errno.
And I will post a patch for 'mount.ocfs2' too.
Link: http://lkml.kernel.org/r/5A4302FA.2010606@huawei.com
Signed-off-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Reviewed-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KarimAllah Ahmed [Wed, 17 Jan 2018 18:18:56 +0000 (19:18 +0100)]
kvm: Map PFN-type memory regions as writable (if possible)
[ Upstream commit
a340b3e229b24a56f1c7f5826b15a3af0f4b13e5 ]
For EPT-violations that are triggered by a read, the pages are also mapped with
write permissions (if their memory region is also writable). That would avoid
getting yet another fault on the same page when a write occurs.
This optimization only happens when you have a "struct page" backing the memory
region. So also enable it for memory regions that do not have a "struct page".
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Wed, 31 Jan 2018 04:21:48 +0000 (22:21 -0600)]
tcp_nv: fix potential integer overflow in tcpnv_acked
[ Upstream commit
e4823fbd229bfbba368b40cdadb8f4eeb20604cc ]
Add suffix ULL to constant 80000 in order to avoid a potential integer
overflow and give the compiler complete information about the proper
arithmetic to use. Notice that this constant is used in a context that
expects an expression of type u64.
The current cast to u64 effectively applies to the whole expression
as an argument of type u64 to be passed to div64_u64, but it does
not prevent it from being evaluated using 32-bit arithmetic instead
of 64-bit arithmetic.
Also, once the expression is properly evaluated using 64-bit arithmentic,
there is no need for the parentheses and the external cast to u64.
Addresses-Coverity-ID:
1357588 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Spencer [Fri, 26 Jan 2018 03:37:50 +0000 (19:37 -0800)]
gianfar: prevent integer wrapping in the rx handler
[ Upstream commit
202a0a70e445caee1d0ec7aae814e64b1189fa4d ]
When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.
For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:
'skb->len == 1600' from the first fragment
size = lstatus & BD_LENGTH_MASK; # 1602
size -= ETH_FCS_LEN; # 1598
size -= skb->len; # -2
Since the size is unsigned, it wraps around and causes a BUG later in
the packet handling, as shown below:
kernel BUG at ./include/linux/skbuff.h:2068!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [
c021ec60] skb_pull+0x24/0x44
LR [
c01e2fbc] gfar_clean_rx_ring+0x498/0x690
Call Trace:
[
df7edeb0] [
c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable)
[
df7edf20] [
c01e33a8] gfar_poll_rx_sq+0x3c/0x9c
[
df7edf40] [
c023352c] net_rx_action+0x21c/0x274
[
df7edf90] [
c0329000] __do_softirq+0xd8/0x240
[
df7edff0] [
c000c108] call_do_irq+0x24/0x3c
[
c0597e90] [
c00041dc] do_IRQ+0x64/0xc4
[
c0597eb0] [
c000d920] ret_from_except+0x0/0x18
--- interrupt: 501 at arch_cpu_idle+0x24/0x5c
Change the size to a signed integer and then trim off any part of the
FCS that was received prior to the last fragment.
Fixes:
6c389fc931bc ("gianfar: fix size of scatter-gathered frames")
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Logan Gunthorpe [Mon, 18 Dec 2017 18:25:05 +0000 (11:25 -0700)]
ntb_transport: Fix bug with max_mw_size parameter
[ Upstream commit
cbd27448faff4843ac4b66cc71445a10623ff48d ]
When using the max_mw_size parameter of ntb_transport to limit the size of
the Memory windows, communication cannot be established and the queues
freeze.
This is because the mw_size that's reported to the peer is correctly
limited but the size used locally is not. So the MW is initialized
with a buffer smaller than the window but the TX side is using the
full window. This means the TX side will be writing to a region of the
window that points nowhere.
This is easily fixed by applying the same limit to tx_size in
ntb_transport_init_queue().
Fixes:
e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leon Romanovsky [Sun, 28 Jan 2018 09:25:30 +0000 (11:25 +0200)]
RDMA/mlx5: Avoid memory leak in case of XRCD dealloc failure
[ Upstream commit
b081808a66345ba725b77ecd8d759bee874cd937 ]
Failure in XRCD FW deallocation command leaves memory leaked and
returns error to the user which he can't do anything about it.
This patch changes behavior to always free memory and always return
success to the user.
Fixes:
e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Bringmann [Tue, 28 Nov 2017 22:58:40 +0000 (16:58 -0600)]
powerpc/numa: Ensure nodes initialized for hotplug
[ Upstream commit
ea05ba7c559c8e5a5946c3a94a2a266e9a6680a6 ]
This patch fixes some problems encountered at runtime with
configurations that support memory-less nodes, or that hot-add CPUs
into nodes that are memoryless during system execution after boot. The
problems of interest include:
* Nodes known to powerpc to be memoryless at boot, but to have CPUs in
them are allowed to be 'possible' and 'online'. Memory allocations
for those nodes are taken from another node that does have memory
until and if memory is hot-added to the node.
* Nodes which have no resources assigned at boot, but which may still
be referenced subsequently by affinity or associativity attributes,
are kept in the list of 'possible' nodes for powerpc. Hot-add of
memory or CPUs to the system can reference these nodes and bring
them online instead of redirecting the references to one of the set
of nodes known to have memory at boot.
Note that this software operates under the context of CPU hotplug. We
are not doing memory hotplug in this code, but rather updating the
kernel's CPU topology (i.e. arch_update_cpu_topology /
numa_update_cpu_topology). We are initializing a node that may be used
by CPUs or memory before it can be referenced as invalid by a CPU
hotplug operation. CPU hotplug operations are protected by a range of
APIs including cpu_maps_update_begin/cpu_maps_update_done,
cpus_read/write_lock / cpus_read/write_unlock, device locks, and more.
Memory hotplug operations, including try_online_node, are protected by
mem_hotplug_begin/mem_hotplug_done, device locks, and more. In the
case of CPUs being hot-added to a previously memoryless node, the
try_online_node operation occurs wholly within the CPU locks with no
overlap. Using HMC hot-add/hot-remove operations, we have been able to
add and remove CPUs to any possible node without failures. HMC
operations involve a degree self-serialization, though.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Bringmann [Tue, 28 Nov 2017 22:58:36 +0000 (16:58 -0600)]
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
[ Upstream commit
a346137e9142b039fd13af2e59696e3d40c487ef ]
On powerpc systems which allow 'hot-add' of CPU or memory resources,
it may occur that the new resources are to be inserted into nodes that
were not used for these resources at bootup. In the kernel, any node
that is used must be defined and initialized. These empty nodes may
occur when,
* Dedicated vs. shared resources. Shared resources require information
such as the VPHN hcall for CPU assignment to nodes. Associativity
decisions made based on dedicated resource rules, such as
associativity properties in the device tree, may vary from decisions
made using the values returned by the VPHN hcall.
* memoryless nodes at boot. Nodes need to be defined as 'possible' at
boot for operation with other code modules. Previously, the powerpc
code would limit the set of possible nodes to those which have
memory assigned at boot, and were thus online. Subsequent add/remove
of CPUs or memory would only work with this subset of possible
nodes.
* memoryless nodes with CPUs at boot. Due to the previous restriction
on nodes, nodes that had CPUs but no memory were being collapsed
into other nodes that did have memory at boot. In practice this
meant that the node assignment presented by the runtime kernel
differed from the affinity and associativity attributes presented by
the device tree or VPHN hcalls. Nodes that might be known to the
pHyp were not 'possible' in the runtime kernel because they did not
have memory at boot.
This patch ensures that sufficient nodes are defined to support
configuration requirements after boot, as well as at boot. This patch
set fixes a couple of problems.
* Nodes known to powerpc to be memoryless at boot, but to have CPUs in
them are allowed to be 'possible' and 'online'. Memory allocations
for those nodes are taken from another node that does have memory
until and if memory is hot-added to the node. * Nodes which have no
resources assigned at boot, but which may still be referenced
subsequently by affinity or associativity attributes, are kept in
the list of 'possible' nodes for powerpc. Hot-add of memory or CPUs
to the system can reference these nodes and bring them online
instead of redirecting to one of the set of nodes that were known to
have memory at boot.
This patch extracts the value of the lowest domain level (number of
allocable resources) from the device tree property
"ibm,max-associativity-domains" to use as the maximum number of nodes
to setup as possibly available in the system. This new setting will
override the instruction:
nodes_and(node_possible_map, node_possible_map, node_online_map);
presently seen in the function arch/powerpc/mm/numa.c:initmem_init().
If the "ibm,max-associativity-domains" property is not present at
boot, no operation will be performed to define or enable additional
nodes, or enable the above 'nodes_and()'.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jake Daryll Obina [Thu, 21 Sep 2017 16:00:14 +0000 (00:00 +0800)]
jffs2: Fix use-after-free bug in jffs2_iget()'s error handling path
[ Upstream commit
5bdd0c6f89fba430e18d636493398389dadc3b17 ]
If jffs2_iget() fails for a newly-allocated inode, jffs2_do_clear_inode()
can get called twice in the error handling path, the first call in
jffs2_iget() itself and the second through iget_failed(). This can result
to a use-after-free error in the second jffs2_do_clear_inode() call, such
as shown by the oops below wherein the second jffs2_do_clear_inode() call
was trying to free node fragments that were already freed in the first
jffs2_do_clear_inode() call.
[ 78.178860] jffs2: error: (1904) jffs2_do_read_inode_internal: CRC failed for read_inode of inode 24 at physical location 0x1fc00c
[ 78.178914] Unable to handle kernel paging request at virtual address
6b6b6b6b6b6b6b7b
[ 78.185871] pgd =
ffffffc03a567000
[ 78.188794] [
6b6b6b6b6b6b6b7b] *pgd=
0000000000000000, *pud=
0000000000000000
[ 78.194968] Internal error: Oops:
96000004 [#1] PREEMPT SMP
...
[ 78.513147] PC is at rb_first_postorder+0xc/0x28
[ 78.516503] LR is at jffs2_kill_fragtree+0x28/0x90 [jffs2]
[ 78.520672] pc : [<
ffffff8008323d28>] lr : [<
ffffff8000eb1cc8>] pstate:
60000105
[ 78.526757] sp :
ffffff800cea38f0
[ 78.528753] x29:
ffffff800cea38f0 x28:
ffffffc01f3f8e80
[ 78.532754] x27:
0000000000000000 x26:
ffffff800cea3c70
[ 78.536756] x25:
00000000dc67c8ae x24:
ffffffc033d6945d
[ 78.540759] x23:
ffffffc036811740 x22:
ffffff800891a5b8
[ 78.544760] x21:
0000000000000000 x20:
0000000000000000
[ 78.548762] x19:
ffffffc037d48910 x18:
ffffff800891a588
[ 78.552764] x17:
0000000000000800 x16:
0000000000000c00
[ 78.556766] x15:
0000000000000010 x14:
6f2065646f6e695f
[ 78.560767] x13:
6461657220726f66 x12:
2064656c69616620
[ 78.564769] x11:
435243203a6c616e x10:
7265746e695f6564
[ 78.568771] x9 :
6f6e695f64616572 x8 :
ffffffc037974038
[ 78.572774] x7 :
bbbbbbbbbbbbbbbb x6 :
0000000000000008
[ 78.576775] x5 :
002f91d85bd44a2f x4 :
0000000000000000
[ 78.580777] x3 :
0000000000000000 x2 :
000000403755e000
[ 78.584779] x1 :
6b6b6b6b6b6b6b6b x0 :
6b6b6b6b6b6b6b6b
...
[ 79.038551] [<
ffffff8008323d28>] rb_first_postorder+0xc/0x28
[ 79.042962] [<
ffffff8000eb5578>] jffs2_do_clear_inode+0x88/0x100 [jffs2]
[ 79.048395] [<
ffffff8000eb9ddc>] jffs2_evict_inode+0x3c/0x48 [jffs2]
[ 79.053443] [<
ffffff8008201ca8>] evict+0xb0/0x168
[ 79.056835] [<
ffffff8008202650>] iput+0x1c0/0x200
[ 79.060228] [<
ffffff800820408c>] iget_failed+0x30/0x3c
[ 79.064097] [<
ffffff8000eba0c0>] jffs2_iget+0x2d8/0x360 [jffs2]
[ 79.068740] [<
ffffff8000eb0a60>] jffs2_lookup+0xe8/0x130 [jffs2]
[ 79.073434] [<
ffffff80081f1a28>] lookup_slow+0x118/0x190
[ 79.077435] [<
ffffff80081f4708>] walk_component+0xfc/0x28c
[ 79.081610] [<
ffffff80081f4dd0>] path_lookupat+0x84/0x108
[ 79.085699] [<
ffffff80081f5578>] filename_lookup+0x88/0x100
[ 79.089960] [<
ffffff80081f572c>] user_path_at_empty+0x58/0x6c
[ 79.094396] [<
ffffff80081ebe14>] vfs_statx+0xa4/0x114
[ 79.098138] [<
ffffff80081ec44c>] SyS_newfstatat+0x58/0x98
[ 79.102227] [<
ffffff800808354c>] __sys_trace_return+0x0/0x4
[ 79.106489] Code:
d65f03c0 f9400001 b40000e1 aa0103e0 (
f9400821)
The jffs2_do_clear_inode() call in jffs2_iget() is unnecessary since
iget_failed() will eventually call jffs2_do_clear_inode() if needed, so
just remove it.
Fixes:
5451f79f5f81 ("iget: stop JFFS2 from using iget() and read_inode()")
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jake Daryll Obina <jake.obina@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Mon, 22 Jan 2018 16:01:42 +0000 (18:01 +0200)]
device property: Define type of PROPERTY_ENRTY_*() macros
[ Upstream commit
c505cbd45f6e9c539d57dd171d95ec7e5e9f9cd0 ]
Some of the drivers may use the macro at runtime flow, like
struct property_entry p[10];
...
p[index++] = PROPERTY_ENTRY_U8("u8 property", u8_data);
In that case and absence of the data type compiler fails the build:
drivers/char/ipmi/ipmi_dmi.c:79:29: error: Expected ; at end of statement
drivers/char/ipmi/ipmi_dmi.c:79:29: error: got {
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ngai-Mint Kwan [Wed, 24 Jan 2018 22:18:22 +0000 (14:18 -0800)]
fm10k: fix "failed to kill vid" message for VF
[ Upstream commit
cf315ea596ec26d7aa542a9ce354990875a920c0 ]
When a VF is under PF VLAN assignment:
ip link set <pf> vf <#> vlan <vid>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Wed, 10 Jan 2018 09:39:03 +0000 (12:39 +0300)]
HID: roccat: prevent an out of bounds read in kovaplus_profile_activated()
[ Upstream commit
7ad81482cad67cbe1ec808490d1ddfc420c42008 ]
We get the "new_profile_index" value from the mouse device when we're
handling raw events. Smatch taints it as untrusted data and complains
that we need a bounds check. This seems like a reasonable warning
otherwise there is a small read beyond the end of the array.
Fixes:
0e70f97f257e ("HID: roccat: Add support for Kova[+] mouse")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anand Jain [Tue, 9 Jan 2018 01:05:43 +0000 (09:05 +0800)]
btrfs: fail mount when sb flag is not in BTRFS_SUPER_FLAG_SUPP
[ Upstream commit
6f794e3c5c8f8fdd3b5bb20d9ded894e685b5bbe ]
It appears from the original commit [1] that there isn't any design
specific reason not to fail the mount instead of just warning. This
patch will change it to fail.
[1]
commit
319e4d0661e5323c9f9945f0f8fb5905e5fe74c3
btrfs: Enhance super validation check
Fixes:
319e4d0661e5323 ("btrfs: Enhance super validation check")
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Bo [Tue, 2 Jan 2018 20:36:41 +0000 (13:36 -0700)]
Btrfs: fix scrub to repair raid6 corruption
[ Upstream commit
762221f095e3932669093466aaf4b85ed9ad2ac1 ]
The raid6 corruption is that,
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content.
We've fixed normal reads to rebuild raid6 correctly with more retries
in Patch "Btrfs: make raid6 rebuild retry more"[1], this is to fix
scrub to do the exactly same rebuild process.
[1]: https://patchwork.kernel.org/patch/
10091755/
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolay Borisov [Tue, 12 Dec 2017 09:14:49 +0000 (11:14 +0200)]
btrfs: Fix out of bounds access in btrfs_search_slot
[ Upstream commit
9ea2c7c9da13c9073e371c046cbbc45481ecb459 ]
When modifying a tree where the root is at BTRFS_MAX_LEVEL - 1 then
the level variable is going to be 7 (this is the max height of the
tree). On the other hand btrfs_cow_block is always called with
"level + 1" as an index into the nodes and slots arrays. This leads to
an out of bounds access. Admittdely this will be benign since an OOB
access of the nodes array will likely read the 0th element from the
slots array, which in this case is going to be 0 (since we start CoW at
the top of the tree). The OOB access into the slots array in turn will
read the 0th and 1st values of the locks array, which would both be 0
at the time. However, this benign behavior relies on the fact that the
path being passed hasn't been initialised, if it has already been used to
query a btree then it could potentially have populated the nodes/slots arrays.
Fix it by explicitly checking if we are at level 7 (the maximum allowed
index in nodes/slots arrays) and explicitly call the CoW routine with
NULL for parent's node/slot.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Fixes-coverity-id: 711515
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Bo [Wed, 15 Nov 2017 23:10:28 +0000 (16:10 -0700)]
Btrfs: set plug for fsync
[ Upstream commit
343e4fc1c60971b0734de26dbbd475d433950982 ]
Setting plug can merge adjacent IOs before dispatching IOs to the disk
driver.
Without plug, it'd not be a problem for single disk usecases, but for
multiple disks using raid profile, a large IO can be split to several
IOs of stripe length, and plug can be helpful to bring them together
for each disk so that we can save several disk access.
Moreover, fsync issues synchronous writes, so plug can really take
effect.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wei Yongjun [Thu, 18 Jan 2018 01:43:19 +0000 (01:43 +0000)]
ipmi/powernv: Fix error return code in ipmi_powernv_probe()
[ Upstream commit
e749d328b0b450aa78d562fa26a0cd8872325dd9 ]
Fix to return a negative error code from the request_irq() error
handling case instead of 0, as done elsewhere in this function.
Fixes:
dce143c3381c ("ipmi/powernv: Convert to irq event interface")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
weiyongjun (A) [Thu, 18 Jan 2018 02:23:34 +0000 (02:23 +0000)]
mac80211_hwsim: fix possible memory leak in hwsim_new_radio_nl()
[ Upstream commit
0ddcff49b672239dda94d70d0fcf50317a9f4b51 ]
'hwname' is malloced in hwsim_new_radio_nl() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes:
ff4dd73dd2b4 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / GitHub / LineageOS / G12 / android_kernel_amlogic_linux-4.9.git / log