GitHub/MotorolaMobilityLLC/kernel-slsi.git
17 years agoSMC911X: Fix using of dereferenced skb after netif_rx
Wang Chen [Tue, 4 Dec 2007 02:01:37 +0000 (10:01 +0800)]
SMC911X: Fix using of dereferenced skb after netif_rx

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agosky2: recovery deadlock fix
Stephen Hemminger [Tue, 4 Dec 2007 01:02:17 +0000 (17:02 -0800)]
sky2: recovery deadlock fix

Prevent deadlock in sky2 recovery logic. sky2_down calls napi_synchronize
which gets stuck if napi was already disabled.

Fix by rearranging slightly and not calling napi_disable until after
both ports are stopped. The napi_disable probably is being overly
paranoid, but it is safe now.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoFix memory corruption in fec_mpc52xx
Jon Smirl [Mon, 3 Dec 2007 22:38:10 +0000 (22:38 +0000)]
Fix memory corruption in fec_mpc52xx

The mpc5200 fec driver is corrupting memory. This patch fixes two bugs
where the wrong skb was being referenced.

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoDon't claim to do IPv6 checksum offload
David Woodhouse [Mon, 3 Dec 2007 04:34:32 +0000 (04:34 +0000)]
Don't claim to do IPv6 checksum offload

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agocxgb - revert file mode changes.
Divy Le Ray [Sat, 1 Dec 2007 23:57:17 +0000 (15:57 -0800)]
cxgb - revert file mode changes.

revert inavertant file mode changes

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoMerge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
Linus Torvalds [Tue, 4 Dec 2007 17:37:39 +0000 (09:37 -0800)]
Merge branch 'for-linus' of git://git390.osdl.marist.edu/linux-2.6

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] Make sure the restore psw masks are initialized.
  [S390] Fix compile error on 31bit without preemption
  [S390] dcssblk: prevent early access without own make_request function
  [S390] cio: add missing reprobe loop end statement
  [S390] cio: Issue SenseID per path.

17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86
Linus Torvalds [Tue, 4 Dec 2007 17:28:45 +0000 (09:28 -0800)]
Merge git://git./linux/kernel/git/x86/linux-2.6-x86

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  x86: arch_register_cpu() section fix
  x86: free_cache_attributes() section fix
  x86: add the word 'WARNING' in check_nmi_watchdog() output
  x86: revert CONFIG_X86_HT semantics change

17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched
Linus Torvalds [Tue, 4 Dec 2007 17:28:23 +0000 (09:28 -0800)]
Merge git://git./linux/kernel/git/mingo/linux-2.6-sched

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: default to more agressive yield for SCHED_BATCH tasks
  sched: fix crash in sys_sched_rr_get_interval()

17 years agoMAINTAINERS: remove the MTRR entry
Adrian Bunk [Tue, 4 Dec 2007 13:35:00 +0000 (14:35 +0100)]
MAINTAINERS: remove the MTRR entry

I haven't seen Richard doing MTRR related work for quite some time, and
the "X86 ARCHITECTURE" entry in MAINTAINERS already covers the people
currently responsible for this code.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agodrivers/s390/net/ctcmain.c: fix build bug
Ingo Molnar [Tue, 4 Dec 2007 10:32:38 +0000 (11:32 +0100)]
drivers/s390/net/ctcmain.c: fix build bug

SET_MODULE_OWNER() is obsolete.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agox86: arch_register_cpu() section fix
Andrew Morton [Tue, 4 Dec 2007 16:19:07 +0000 (17:19 +0100)]
x86: arch_register_cpu() section fix

fix this on i386 allnoconfig:

 WARNING: vmlinux.o(.text+0x6f2e): Section mismatch: reference to .init.text:register_cpu (between 'arch_register_cpu' and 'text_poke')

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
17 years agox86: free_cache_attributes() section fix
Adrian Bunk [Tue, 4 Dec 2007 16:19:07 +0000 (17:19 +0100)]
x86: free_cache_attributes() section fix

free_cache_attributes() must be __cpuinit since it calls the
__cpuinit cache_remove_shared_cpu_map().

This patch fixes the following section mismatch reported by
Chris Clayton:

 ...
 WARNING: vmlinux.o(.text+0x90b6): Section mismatch: reference to .init.text:cache_remove_shared_cpu_map (between 'free_cache_attributes' and 'show_level')
 ...

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
17 years agox86: add the word 'WARNING' in check_nmi_watchdog() output
Don Zickus [Tue, 4 Dec 2007 16:19:07 +0000 (17:19 +0100)]
x86: add the word 'WARNING' in check_nmi_watchdog() output

Our automated test suite looks for keywords like error, fail, warning in
the boot log.  In the case when the nmi watchdog is determined to be
stuck in check_nmi_watchdog(), none of those keywords are displayed.

This patch adds a keyword, "WARNING:", so it makes it easier to notice
when the nmi watchdog isn't working correctly. Also add a proper
KERN_WARNING mark to this printout.

Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
17 years agox86: revert CONFIG_X86_HT semantics change
Adrian Bunk [Tue, 4 Dec 2007 16:19:07 +0000 (17:19 +0100)]
x86: revert CONFIG_X86_HT semantics change

The recent Kconfig changes in x86 resulted in CONFIG_X86_HT no longer
being set if (X86_32 && MK8).

After grep'ing through the tree I think the problem is that different
places have different assumptions about the semantics of CONFIG_X86_HT,
either:

- hyperthreading or
- multicore

This should be sorted out properly, but until then we should keep the
2.6.23 status quo.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
17 years agosched: default to more agressive yield for SCHED_BATCH tasks
Ingo Molnar [Tue, 4 Dec 2007 16:04:39 +0000 (17:04 +0100)]
sched: default to more agressive yield for SCHED_BATCH tasks

do more agressive yield for SCHED_BATCH tuned tasks: they are all
about throughput anyway. This allows a gentler migration path for
any apps that relied on stronger yield.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
17 years agosched: fix crash in sys_sched_rr_get_interval()
Ingo Molnar [Tue, 4 Dec 2007 16:04:39 +0000 (17:04 +0100)]
sched: fix crash in sys_sched_rr_get_interval()

Luiz Fernando N. Capitulino reported that sched_rr_get_interval()
crashes for SCHED_OTHER tasks that are on an idle runqueue.

The fix is to return a 0 timeslice for tasks that are on an idle
runqueue. (and which are not running, obviously)

this also shrinks the code a bit:

   text    data     bss     dec     hex filename
  47903    3934     336   52173    cbcd sched.o.before
  47885    3934     336   52155    cbbb sched.o.after

Reported-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
17 years ago[S390] Make sure the restore psw masks are initialized.
Heiko Carstens [Tue, 4 Dec 2007 15:09:05 +0000 (16:09 +0100)]
[S390] Make sure the restore psw masks are initialized.

In case of TRACE_IRQFLAGS the restore psw masks will not be
initialized if noexec is turned on. This will lead to an
immediate system crash.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
17 years ago[S390] Fix compile error on 31bit without preemption
Christian Borntraeger [Tue, 4 Dec 2007 15:09:04 +0000 (16:09 +0100)]
[S390] Fix compile error on 31bit without preemption

Commit b8e7a54cd06b0b0174029ef3a7f5a1415a2c28f2 introduced a compile
error if CONFIG_PREEMPT is not set:

arch/s390/kernel/built-in.o: In function `cleanup_io_leave_insn':
/space/kvm/arch/s390/kernel/entry.S:(.text+0xbfce): undefined reference to `preempt_schedule_irq'

This patch hides preempt_schedule_irq if CONFIG_PREEMPT is not set.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
17 years ago[S390] dcssblk: prevent early access without own make_request function
Christian Borntraeger [Tue, 4 Dec 2007 15:09:03 +0000 (16:09 +0100)]
[S390] dcssblk: prevent early access without own make_request function

When loading a dcss segment with the dcssblk driver, sometimes the
following kind of message appears:

bio too big device dcssblk0 (8 > 0)
Buffer I/O error on device dcssblk0, logical block 172016
..

The fix is to move the disk registration after setting the
make_request function, to avoid calls into generic_make_request
for dcssblock without having the make_request function set up
properly.

Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
17 years ago[S390] cio: add missing reprobe loop end statement
Peter Oberparleiter [Tue, 4 Dec 2007 15:09:02 +0000 (16:09 +0100)]
[S390] cio: add missing reprobe loop end statement

Add loop end statement to prevent looping over empty subchannel sets.

Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
17 years ago[S390] cio: Issue SenseID per path.
Cornelia Huck [Tue, 4 Dec 2007 15:09:01 +0000 (16:09 +0100)]
[S390] cio: Issue SenseID per path.

We may receive a unit check for every path when we issue a SenseID.
Unfortunately, the channel subsystem will try on a different path
every time if we use a lpm of 0xff, which will exhaust our retry
counter.

Therefore, revert SenseID to its previous per-path behaviour and
just leave out the suspend multipath reconnect.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
17 years agoLinux 2.6.24-rc4
Linus Torvalds [Tue, 4 Dec 2007 04:26:10 +0000 (20:26 -0800)]
Linux 2.6.24-rc4

17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24
Linus Torvalds [Mon, 3 Dec 2007 23:46:37 +0000 (15:46 -0800)]
Merge git://git./linux/kernel/git/lethal/sh-2.6.24

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
  sh: Support PCI IO access of SH7780 base boards.
  sh: Fix PCI IO space base address of SH7780.

17 years ago[MIPS] BCM1480: Fix interrupt routing.
Ralf Baechle [Sun, 2 Dec 2007 12:09:11 +0000 (12:09 +0000)]
[MIPS] BCM1480: Fix interrupt routing.

The old code did did only work as long as CFE and the kernel were using
the same interrupt numbering ...

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86
Linus Torvalds [Mon, 3 Dec 2007 16:45:15 +0000 (08:45 -0800)]
Merge git://git./linux/kernel/git/x86/linux-2.6-x86

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  x86: fix x86-32 early fixmap initialization.
  x86: disable hpet legacy replacement for kdump
  x86: disable hpet on shutdown

17 years agoMerge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
Linus Torvalds [Mon, 3 Dec 2007 16:23:58 +0000 (08:23 -0800)]
Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Remove xmon from ml300 and ml403 defconfig in arch/ppc
  Revert "[POWERPC] Fix RTAS os-term usage on kernel panic"

17 years agoMerge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux...
Linus Torvalds [Mon, 3 Dec 2007 16:23:32 +0000 (08:23 -0800)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference
  ACPI: Delete the IRQ operation in throttling controll via PTC

17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched
Linus Torvalds [Mon, 3 Dec 2007 16:21:06 +0000 (08:21 -0800)]
Merge git://git./linux/kernel/git/mingo/linux-2.6-sched

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: cpu accounting controller (V2)

17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
Linus Torvalds [Mon, 3 Dec 2007 16:20:11 +0000 (08:20 -0800)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] NCR5380: Fix bugs and canonicalize irq handler usage
  [SCSI] zfcp: fix cleanup of dismissed error recovery actions
  [SCSI] zfcp: fix dismissal of error recovery actions
  [SCSI] qla1280: convert to use the data buffer accessors
  [SCSI] iscsi: return data transfer residual for data-out commands
  [SCSI] iscsi_tcp: fix potential lockup with write commands
  [SCSI] aacraid: fix security weakness
  [SCSI] aacraid: fix up le32 issues in BlinkLED
  [SCSI] aacraid: fix potential panic in thread stop
  [SCSI] aacraid: don't assign cpu_to_le32(constant) to u8

17 years agox86: fix x86-32 early fixmap initialization.
Eric W. Biederman [Sun, 2 Dec 2007 01:34:06 +0000 (18:34 -0700)]
x86: fix x86-32 early fixmap initialization.

pageexec@freemail.hu writes:

> i've just noticed that the chunk in i386/kernel/head.S ended up in a
> weird place, namely, it's not going to be executed as it's just after
> a 'jmp 3f' and before startup_32_smp, probably not what you intended.
> on a sidenote, the whole thing can be done in a single insn, like:
>
> movl $(swapper_pg_pmd - __PAGE_OFFSET + 0x067), (swapper_pg_dir -
> __PAGE_OFFSET+ 4092)

Thanks for the reminder I thought we had fixed this problem a while ago.

Needed to get fixed virtual address for USB debug and earlycon with mmio.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
17 years agox86: disable hpet legacy replacement for kdump
OGAWA Hirofumi [Mon, 3 Dec 2007 16:17:10 +0000 (17:17 +0100)]
x86: disable hpet legacy replacement for kdump

we should also add hpet_disable() for kdump.

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
17 years agox86: disable hpet on shutdown
OGAWA Hirofumi [Mon, 3 Dec 2007 16:17:10 +0000 (17:17 +0100)]
x86: disable hpet on shutdown

If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.

The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.

If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6
Linus Torvalds [Mon, 3 Dec 2007 16:15:36 +0000 (08:15 -0800)]
Merge git://git./linux/kernel/git/herbert/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
  [INET]: Fix inet_diag dead-lock regression
  [NETNS]: Fix /proc/net breakage
  [TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
  [NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
  [NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
  [DECNET]: dn_nl_deladdr() almost always returns no error
  [IPV6]: Restore IPv6 when MTU is big enough
  [RXRPC]: Add missing select on CRYPTO
  mac80211: rate limit wep decrypt failed messages
  rfkill: fix double-mutex-locking
  mac80211: drop unencrypted frames if encryption is expected
  mac80211: Fix behavior of ieee80211_open and ieee80211_close
  ieee80211: fix unaligned access in ieee80211_copy_snap
  mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
  SCTP: Fix build issues with SCTP AUTH.
  SCTP: Fix chunk acceptance when no authenticated chunks were listed.
  SCTP: Fix the supported extensions paramter
  SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
  SCTP: Fix the number of HB transmissions.
  [TCP] illinois: Incorrect beta usage
  ...

17 years agoMerge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzi...
Linus Torvalds [Mon, 3 Dec 2007 16:15:08 +0000 (08:15 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/netdev-2.6

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
  LIB82596: correct data types for hardware addresses
  via-velocity: don't oops on MTU change (resend)
  Stop phy code from returning success to unknown ioctls.
  SET_NETDEV_DEV() in fec_mpc52xx.c
  net: smc911x: only enable for mpr2 on sh.
  e1000: Fix NAPI state bug when Rx complete
  sky2: turn of dynamic Tx watermark workaround (FE+ only)
  sky2: don't use AER routines
  sky2: revert to access PCI config via device space
  cxgb - fix stats
  cxgb - fix NAPI
  cxgb - fix T2 GSO
  ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters
  phylib: marvell: add support for TX-only and RX-only Internal Delay
  phylib: add PHY interface modes for internal delay for tx and rx only
  skge: MTU changing fix
  skge: serial mode register values
  skge version 1.13
  skge: increase TX threshold for Jumbo
  skge: fiber link up/down fix
  ...

17 years agoMerge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzi...
Linus Torvalds [Mon, 3 Dec 2007 16:14:45 +0000 (08:14 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_mv: Fix broken Marvell 7042 support.
  libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
  ata_piix: add more toshiba laptops to broken suspend list
  libata: More IVB horkage from TSST
  libata: report protocol and full CDB on error
  Several fixes for the AVR32 PATA driver
  sata_mv: fix compilation error when enabling DEBUG
  Set proper ATA UDMA mode for bf548 according to system clock.

17 years agoUpdate Kdump Maintainer's details
Vivek Goyal [Sat, 1 Dec 2007 20:16:30 +0000 (12:16 -0800)]
Update Kdump Maintainer's details

Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agouml: work around host tcsetattr bug
Jeff Dike [Sat, 1 Dec 2007 20:16:30 +0000 (12:16 -0800)]
uml: work around host tcsetattr bug

Under the conditions that UML uses it, tcgetattr is guaranteed to return
-EINTR when the console is attached to /dev/ptmx, making generic_console_write
hang because it loops, calling tcgetattr until it succeeds.  This is a host
bug - see http://marc.info/?l=linux-kernel&m=119618990807182&w=2 for the
details.

This patch works around it by blocking SIGIO while the terminal attributes are
being fiddled.

Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agouml: after_sleep_interval should return something
Jeff Dike [Sat, 1 Dec 2007 20:16:29 +0000 (12:16 -0800)]
uml: after_sleep_interval should return something

I forgot to have an int-returning function actually return something.

Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agouml: add !UML dependencies
Al Viro [Sat, 1 Dec 2007 20:16:29 +0000 (12:16 -0800)]
uml: add !UML dependencies

The previous commit ("uml: keep UML Kconfig in sync with x86") is not
enough, unfortunately.  If we go that way, we need to add dependencies
on !UML for several options.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agouml: keep UML Kconfig in sync with x86
Jeff Dike [Sat, 1 Dec 2007 20:16:28 +0000 (12:16 -0800)]
uml: keep UML Kconfig in sync with x86

Fix a UML build breakage introduced by commit
1032c0ba9da5c5b53173ad2dcf8b2a2da78f8b17 - it introduces X86_32, with many
things which UML needs depending on it.

This patch adds definitions of X86_32 and RWSEM_XCHGADD_ALGORITHM to
the UML/i386 Kconfig.

Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoI4L: fix isdn_ioctl memory overrun vulnerability
Karsten Keil [Sat, 1 Dec 2007 20:16:15 +0000 (12:16 -0800)]
I4L: fix isdn_ioctl memory overrun vulnerability

Fix possible memory overrun issue in the isdn ioctl code.

Found by ADLAB <adlab@venustech.com.cn>

Signed-off-by: Karsten Keil <kkeil@suse.de>
Cc: ADLAB <adlab@venustech.com.cn>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years ago[INET]: Fix inet_diag dead-lock regression
Herbert Xu [Mon, 3 Dec 2007 04:51:25 +0000 (15:51 +1100)]
[INET]: Fix inet_diag dead-lock regression

The inet_diag register fix broke inet_diag module loading because the
loaded module had to take the same mutex that's already held by the
loader in order to register the new handler.

This patch fixes it by introducing a separate mutex to protect the
handling of handlers.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years ago[POWERPC] Remove xmon from ml300 and ml403 defconfig in arch/ppc
Grant Likely [Tue, 20 Nov 2007 06:08:49 +0000 (17:08 +1100)]
[POWERPC] Remove xmon from ml300 and ml403 defconfig in arch/ppc

xmon is broken under arch/ppc so remove it from the defconfig.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
17 years agoRevert "[POWERPC] Fix RTAS os-term usage on kernel panic"
Paul Mackerras [Sun, 2 Dec 2007 22:30:04 +0000 (09:30 +1100)]
Revert "[POWERPC] Fix RTAS os-term usage on kernel panic"

This reverts commit a2b51812a4dc5db09ab4d4638d4d8ed456e2457e.

It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines.  The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called.  Until that is clarified I'm reverting this commit.

Signed-off-by: Paul Mackerras <paulus@samba.org>
17 years agoPull bugzilla-9429 into release branch
Len Brown [Sun, 2 Dec 2007 19:33:33 +0000 (14:33 -0500)]
Pull bugzilla-9429 into release branch

17 years agoPull thermal into release branch
Len Brown [Sun, 2 Dec 2007 19:33:21 +0000 (14:33 -0500)]
Pull thermal into release branch

17 years agoACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference
Bob Moore [Wed, 17 Oct 2007 20:10:18 +0000 (16:10 -0400)]
ACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference

Changed resolution of named references in packages

Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.

http://bugzilla.kernel.org/show_bug.cgi?id=5328
http://bugzilla.kernel.org/show_bug.cgi?id=9429

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
17 years agosched: cpu accounting controller (V2)
Srivatsa Vaddagiri [Sun, 2 Dec 2007 19:04:49 +0000 (20:04 +0100)]
sched: cpu accounting controller (V2)

Commit cfb5285660aad4931b2ebbfa902ea48a37dfffa1 removed a useful feature for
us, which provided a cpu accounting resource controller.  This feature would be
useful if someone wants to group tasks only for accounting purpose and doesnt
really want to exercise any control over their cpu consumption.

The patch below reintroduces the feature. It is based on Paul Menage's
original patch (Commit 62d0df64065e7c135d0002f069444fbdfc64768f), with
these differences:

        - Removed load average information. I felt it needs more thought (esp
  to deal with SMP and virtualized platforms) and can be added for
  2.6.25 after more discussions.
        - Convert group cpu usage to be nanosecond accurate (as rest of the cfs
  stats are) and invoke cpuacct_charge() from the respective scheduler
  classes
- Make accounting scalable on SMP systems by splitting the usage
  counter to be per-cpu
- Move the code from kernel/cpu_acct.c to kernel/sched.c (since the
  code is not big enough to warrant a new file and also this rightly
  needs to live inside the scheduler. Also things like accessing
  rq->lock while reading cpu usage becomes easier if the code lived in
  kernel/sched.c)

The patch also modifies the cpu controller not to provide the same accounting
information.

Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>
 Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran
 some simple tests like cpuspin (spin on the cpu), ran several tasks in
 the same group and timed them. Compared their time stamps with
 cpuacct.usage.

Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
17 years agoACPI: Delete the IRQ operation in throttling controll via PTC
Zhao Yakui [Thu, 29 Nov 2007 08:22:43 +0000 (16:22 +0800)]
ACPI: Delete the IRQ operation in throttling controll via PTC

The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.

This fixes an oops on T61 -- a regression due to
f79f06ab9f86 b/c FixedHW support tried to read remote MSR with interrupts disabled.

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
17 years agosata_mv: Fix broken Marvell 7042 support.
Mark Lord [Sat, 1 Dec 2007 18:07:22 +0000 (13:07 -0500)]
sata_mv: Fix broken Marvell 7042 support.

sata_mv:  Fix broken Marvell 7042 support.

The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus.  Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.

This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.

Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.

This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.

Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.

Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agolibata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port...
Alan Cox [Fri, 30 Nov 2007 15:23:16 +0000 (15:23 +0000)]
libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))

On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:

> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.

Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoata_piix: add more toshiba laptops to broken suspend list
Peter Schwenke [Fri, 30 Nov 2007 06:28:29 +0000 (15:28 +0900)]
ata_piix: add more toshiba laptops to broken suspend list

Add more toshiba laptops to broken suspend list.  This is from OSDL
bugzilla bug 7780.

tj: re-formatted patch and added description and SOB.

Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agolibata: More IVB horkage from TSST
Peter Missel [Tue, 27 Nov 2007 17:04:42 +0000 (18:04 +0100)]
libata: More IVB horkage from TSST

libata: Add more TSST (Samsung/Toshiba) IDE drives with broken
cable detection validation bits.

signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agolibata: report protocol and full CDB on error
Tejun Heo [Wed, 28 Nov 2007 14:16:09 +0000 (23:16 +0900)]
libata: report protocol and full CDB on error

Protocol and CDB allocation size field are important in determining
what went wrong with ATAPI commands.  Report them on failure.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoSeveral fixes for the AVR32 PATA driver
Kristoffer Nyborg Gregertsen [Thu, 29 Nov 2007 11:01:51 +0000 (12:01 +0100)]
Several fixes for the AVR32 PATA driver

Several fixes for the AVR32 PATA driver:

* Updated to use new AVR32 SMC timing API. This removes the need for "magic"
constants in signal timing.

* Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts.

* Removed .port_disable and .irq_ack as these are no longer needed.

* Improved some comments.

Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agosata_mv: fix compilation error when enabling DEBUG
Saeed Bishara [Tue, 27 Nov 2007 15:26:08 +0000 (17:26 +0200)]
sata_mv: fix compilation error when enabling DEBUG

use sstatus instead status.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoSet proper ATA UDMA mode for bf548 according to system clock.
sonic zhang [Tue, 27 Nov 2007 04:47:39 +0000 (12:47 +0800)]
Set proper ATA UDMA mode for bf548 according to system clock.

UDMA Mode - Frequency compatibility

UDMA5 - 100 MB/s   - SCLK  = 133 MHz
UDMA4 - 66 MB/s    - SCLK >=  80 MHz
UDMA3 - 44.4 MB/s  - SCLK >=  50 MHz
UDMA2 - 33 MB/s    - SCLK >=  40 MHz

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoLIB82596: correct data types for hardware addresses
Thomas Bogendoerfer [Fri, 30 Nov 2007 22:13:16 +0000 (23:13 +0100)]
LIB82596: correct data types for hardware addresses

dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS),
so it's not a good idea to use it for 32bit wide addresses in descriptors.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agovia-velocity: don't oops on MTU change (resend)
Stephen Hemminger [Wed, 28 Nov 2007 22:20:16 +0000 (14:20 -0800)]
via-velocity: don't oops on MTU change (resend)

The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized.  This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoStop phy code from returning success to unknown ioctls.
David Woodhouse [Wed, 28 Nov 2007 19:56:34 +0000 (19:56 +0000)]
Stop phy code from returning success to unknown ioctls.

This kind of sucks, and prevents the Fedora installer from using the
device for network installs...

[root@efika phy]# iwconfig eth0
Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...

eth0        ESSID:off/any  Nickname:""
          NWID:0  Channel:0  Access Point: 00:00:BF:81:14:E0
          Bit Rate:-1.08206e+06 kb/s   Sensitivity=0/0
          RTS thr:off   Fragment thr:off
          Encryption key:<too big>
          Power Management:off

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoSET_NETDEV_DEV() in fec_mpc52xx.c
David Woodhouse [Wed, 28 Nov 2007 18:04:31 +0000 (18:04 +0000)]
SET_NETDEV_DEV() in fec_mpc52xx.c

This helps to allow the Fedora installer to use the built-in Ethernet on
the Efika for a network install.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agonet: smc911x: only enable for mpr2 on sh.
Paul Mundt [Wed, 28 Nov 2007 09:24:59 +0000 (18:24 +0900)]
net: smc911x: only enable for mpr2 on sh.

The smc911x.h is a bit of a mess, not supporting any sort of generic
configuration. For the moment only ARCH_PXA and SH_MAGIC_PANEL_R2 have
suitable definitions, so we reflect this in the Kconfig also.

While there are other SH boards that will likely turn this on in the
2.6.25 time frame, it's not worth trying to stub around at the moment.

Fixes up the allmodconfig build, as noted by akpm.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoe1000: Fix NAPI state bug when Rx complete
Auke Kok [Wed, 28 Nov 2007 00:26:36 +0000 (16:26 -0800)]
e1000: Fix NAPI state bug when Rx complete

Don't exit polling when we have not yet used our budget, this causes
the NAPI system to end up with a messed up poll list.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agosky2: turn of dynamic Tx watermark workaround (FE+ only)
Stephen Hemminger [Tue, 27 Nov 2007 19:02:07 +0000 (11:02 -0800)]
sky2: turn of dynamic Tx watermark workaround (FE+ only)

Add workaround for issues FE+ (A0) transmit watermark.
This is copied verbatim from vendor driver sk98lin (10.22.4.3).
Don't have that chip version and no more information seems to be available.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agosky2: don't use AER routines
Stephen Hemminger [Tue, 27 Nov 2007 19:02:32 +0000 (11:02 -0800)]
sky2: don't use AER routines

Using PCIE advanced error recovery stuff creates more user problems than it's worth.
The AER stuff depends on MMCONFIG and in many configurations it just doesn't work.
Plus it doesn't add any real functionality to the driver. The sky2
driver handles its own errors fine as is.

This reverts 555382cbfc6d2187b53888190755e56f52308cd6

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agosky2: revert to access PCI config via device space
Stephen Hemminger [Tue, 27 Nov 2007 18:57:27 +0000 (10:57 -0800)]
sky2: revert to access PCI config via device space

Using the hardware window into PCI config space is more reliable
and smaller/faster than using the pci_config routines. It avoids issues
with MMCONFIG etc.

Reverts: 167f53d05fccb47b6eeadac7f6705b3f2f042d03

Please apply for 2.6.24

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agocxgb - fix stats
Divy Le Ray [Tue, 27 Nov 2007 21:30:20 +0000 (13:30 -0800)]
cxgb - fix stats

Fix MAC stats accounting.
Fix get_stats.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agocxgb - fix NAPI
Divy Le Ray [Tue, 27 Nov 2007 21:30:15 +0000 (13:30 -0800)]
cxgb - fix NAPI

netif_rx_complete() should be called only
when work_done < budget.

Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agocxgb - fix T2 GSO
Divy Le Ray [Tue, 27 Nov 2007 21:30:09 +0000 (13:30 -0800)]
cxgb - fix T2 GSO

The patch ensures that a GSO skb has enough headroom
to push an encapsulating cpl_tx_pkt_lso header.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type...
Kim Phillips [Mon, 26 Nov 2007 22:17:58 +0000 (16:17 -0600)]
ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters

Extend the RGMII-Internal Delay specification case to include
TX-only and RX-only variants.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agophylib: marvell: add support for TX-only and RX-only Internal Delay
Kim Phillips [Mon, 26 Nov 2007 22:17:52 +0000 (16:17 -0600)]
phylib: marvell: add support for TX-only and RX-only Internal Delay

Previously, Internal Delay specification implied the delay be
applied to both TX and RX.  This patch allows for separate TX/RX-only
internal delay specification.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agophylib: add PHY interface modes for internal delay for tx and rx only
Kim Phillips [Mon, 26 Nov 2007 22:17:48 +0000 (16:17 -0600)]
phylib: add PHY interface modes for internal delay for tx and rx only

Allow phylib specification of cases where hardware needs to configure
PHYs for Internal Delay only on either RX or TX (not both).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge: MTU changing fix
Stephen Hemminger [Wed, 28 Nov 2007 22:25:05 +0000 (14:25 -0800)]
skge: MTU changing fix

The code to change MTU doesn't correctly handle all the chip variations
and requirements for restarting.  On Genesis chips changing MTU would just
cause receiver to hang.
Use a simpler approach of just taking link down/up if needed.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge: serial mode register values
Stephen Hemminger [Wed, 28 Nov 2007 22:23:01 +0000 (14:23 -0800)]
skge: serial mode register values

For compatiablity with sk98lin, make sure and set same values
in serial mode register.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge version 1.13
Stephen Hemminger [Mon, 26 Nov 2007 19:54:53 +0000 (11:54 -0800)]
skge version 1.13

Version for 2.6.24

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge: increase TX threshold for Jumbo
Stephen Hemminger [Mon, 26 Nov 2007 19:54:52 +0000 (11:54 -0800)]
skge: increase TX threshold for Jumbo

Need to increase TX threshold when doing Jumbo frames on dual port board
to avoid underruns. (Code from sk98lin).

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge: fiber link up/down fix
Stephen Hemminger [Mon, 26 Nov 2007 19:54:51 +0000 (11:54 -0800)]
skge: fiber link up/down fix

The driver would not work over fibre if other end when down then
came back up (would require reloading driver). The correct way
to manage the link the same way for both TP and fibre.

Resloves problem described in:   http://lkml.org/lkml/2007/11/6/395

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge: retry on MAC shutdown
Stephen Hemminger [Mon, 26 Nov 2007 19:54:50 +0000 (11:54 -0800)]
skge: retry on MAC shutdown

Make sure and retry when shutting down the MAC. This code is copied
from sk98lin driver.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge: receive flush logic
Stephen Hemminger [Mon, 26 Nov 2007 19:54:49 +0000 (11:54 -0800)]
skge: receive flush logic

Receive FIFO overrun is not catastrophic condition, so don't flush when
it happens.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoskge: FIFO Ram calculation error
Stephen Hemminger [Mon, 26 Nov 2007 19:54:48 +0000 (11:54 -0800)]
skge: FIFO Ram calculation error

The calculation of usable FIFO RAM is wrong in the skge driver.
First, is doesn't take into account the reserved area on the original
SysKonnect Genesis boards. Second it has an off-by-one error because
hw->ports is either 1 or 2.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoctc: make use of alloc_netdev()
Peter Tiedemann [Thu, 29 Nov 2007 16:36:27 +0000 (17:36 +0100)]
ctc: make use of alloc_netdev()

Currently ctc-device initialization is broken (kernel bug in
ctc_new_device).
The new network namespace code reveals a deficiency of the
ctc driver. It should make use of alloc_netdev() as described
in Documentation/networking/netdevices.txt.

Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoS2io: Fixed the case when the card initialization fails on mtu change
Sreenivasa Honnur [Fri, 30 Nov 2007 06:46:08 +0000 (01:46 -0500)]
S2io: Fixed the case when the card initialization fails on mtu change

Fix the case when the card initialization fails on a mtu change and then
close is called (due to ifdown), which frees non existent rx buffers.
- Returning appropriate error codes in init_nic function.
- In s2io_close function s2io_card_down is called only when device is up.
- In s2io_change_mtu function return value of s2io_card_up function
  is checked and returned if it failed.

Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoMerge branch 'fixes-jgarzik' of git://git.kernel.org/pub/scm/linux/kernel/git/linvill...
Jeff Garzik [Sat, 1 Dec 2007 21:20:02 +0000 (16:20 -0500)]
Merge branch 'fixes-jgarzik' of git://git./linux/kernel/git/linville/wireless-2.6 into upstream-fixes

17 years agoMerge branch 'master' into upstream-fixes
Jeff Garzik [Sat, 1 Dec 2007 21:18:56 +0000 (16:18 -0500)]
Merge branch 'master' into upstream-fixes

17 years ago[NETNS]: Fix /proc/net breakage
Eric W. Biederman [Sat, 1 Dec 2007 13:33:17 +0000 (00:33 +1100)]
[NETNS]: Fix /proc/net breakage

Well I clearly goofed when I added the initial network namespace support
for /proc/net.  Currently things work but there are odd details visible to
user space, even when we have a single network namespace.

Since we do not cache proc_dir_entry dentries at the moment we can just
modify ->lookup to return a different directory inode depending on the
network namespace of the process looking at /proc/net, replacing the
current technique of using a magic and fragile follow_link method.

To accomplish that this patch:
- introduces a shadow_proc method to allow different dentries to
  be returned from proc_lookup.
- Removes the old /proc/net follow_link magic
- Fixes a weakness in our not caching of proc generic dentries.

As shadow_proc uses a task struct to decided which dentry to return we can
go back later and fix the proc generic caching without modifying any code
that uses the shadow_proc method.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland...
Linus Torvalds [Sat, 1 Dec 2007 04:07:54 +0000 (20:07 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ehca: Fix static rate if path faster than link
  IPoIB: Fix oops if xmit is called when priv->broadcast is NULL

17 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Sat, 1 Dec 2007 01:07:38 +0000 (17:07 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix build.
  [MIPS] Fix use of smp_processor_id() in preemptible code.

17 years ago[MIPS] Fix build.
Ralf Baechle [Wed, 28 Nov 2007 15:07:42 +0000 (15:07 +0000)]
[MIPS] Fix build.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
17 years ago[MIPS] Fix use of smp_processor_id() in preemptible code.
Pavel Kiryukhin [Tue, 27 Nov 2007 16:20:47 +0000 (19:20 +0300)]
[MIPS] Fix use of smp_processor_id() in preemptible code.

Freeing prom memory: 956kb freed
Freeing firmware memory: 978944k freed
Freeing unused kernel memory: 180k freed
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1
caller is r4k_dma_cache_wback_inv+0x144/0x2a0
Call Trace:
 [<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0
 [<802e4b84>] debug_smp_processor_id+0xd4/0xf0
 [<802e4b7c>] debug_smp_processor_id+0xcc/0xf0
...
CONFIG_DEBUG_PREEMPT is enabled.
--
Bug cause is blast_dcache_range() in preemptible code [in
r4k_dma_cache_wback_inv()].
blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that
uses cpu_dcache_line_size(). It uses current_cpu_data that use
smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT
smp_processor_id emits BUG if we are executing with preemption
enabled.

Cpu options of cpu0 are assumed to be the superset of all processors.

Can I make the same assumptions for cache line size  and fix this
issue the following way:

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
17 years agoIB/ehca: Fix static rate if path faster than link
Joachim Fenkes [Sat, 1 Dec 2007 00:19:41 +0000 (16:19 -0800)]
IB/ehca: Fix static rate if path faster than link

The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling).  Clamp to 0, which is the
correct value.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
17 years agoMerge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Fri, 30 Nov 2007 16:11:18 +0000 (08:11 -0800)]
Merge branch 'for-linus' of /home/rmk/linux-2.6-arm

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4680/1: parentheses around NR_IRQS definition
  [ARM] 4679/1: AT91: Change maintainer email address
  [ARM] 4675/1: pxa: fix mfp address definition error for pxa320
  [ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
  [ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
  [ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
  [ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
  [ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
  [ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
  [ARM] uengine: fix memset size error
  [ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
  [ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
  [ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
  [ARM] 4604/2: AT91: Master clock divistor on SAM9
  [ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
  [ARM] PXA ssp: unlock when ssp tries to close an invalid port
  [ARM] 4654/1: pxa: update default MFP register value
  [ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
  [ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
  [ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions

17 years agoFix kmem_cache_free performance regression in slab
Matthew Wilcox [Thu, 29 Nov 2007 19:05:13 +0000 (12:05 -0700)]
Fix kmem_cache_free performance regression in slab

The database performance group have found that half the cycles spent
in kmem_cache_free are spent in this one call to BUG_ON.  Moving it
into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a
performance win of almost 0.5% on their particular benchmark.

The call was added as part of commit ddc2e812d592457747c4367fb73edcaa8e1e49ff
with the comment that "overhead should be minimal".  It may have been
minimal at the time, but it isn't now.

[ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the
  performance regression but rather the virt_to_head_page() changes to
  virt_to_cache() that were added later." ]

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years ago[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
Pablo Neira Ayuso [Fri, 30 Nov 2007 13:03:52 +0000 (00:03 +1100)]
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure

If a zero length pattern is passed then return EINVAL.
Avoids infinite loops (bm) or invalid memory accesses (kmp).

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years ago[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
Jan Engelhardt [Fri, 30 Nov 2007 13:01:50 +0000 (00:01 +1100)]
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK

Fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK

When xt_CONNMARK is used outside the mangle table and the user specified
"--restore-mark", the connmark_tg_check() function will (correctly)
error out, but (incorrectly) forgets to release the L3 conntrack module.
Same for xt_CONNSECMARK.

Fix is to move the call to acquire the L3 module after the basic
constraint checks.

Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years ago[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
Patrick McHardy [Fri, 30 Nov 2007 12:58:03 +0000 (23:58 +1100)]
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON

ipv6_skip_exthdr() returns -1 for invalid packets. don't WARN_ON
that.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years ago[DECNET]: dn_nl_deladdr() almost always returns no error
Pavel Emelyanov [Fri, 30 Nov 2007 12:43:31 +0000 (23:43 +1100)]
[DECNET]: dn_nl_deladdr() almost always returns no error

As far as I see from the err variable initialization
the dn_nl_deladdr() routine was designed to report errors
like "EADDRNOTAVAIL" and probaby "ENODEV".

But the code sets this err to 0 after the first nlmsg_parse
and goes on, returning this 0 in any case.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years ago[IPV6]: Restore IPv6 when MTU is big enough
Evgeniy Polyakov [Fri, 30 Nov 2007 12:36:08 +0000 (23:36 +1100)]
[IPV6]: Restore IPv6 when MTU is big enough

Avaid provided test application, so bug got fixed.

IPv6 addrconf removes ipv6 inner device from netdev each time cmu
changes and new value is less than IPV6_MIN_MTU (1280 bytes).
When mtu is changed and new value is greater than IPV6_MIN_MTU,
it does not add ipv6 addresses and inner device bac.

This patch fixes that.

Tested with Avaid's application, which works ok now.

Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years ago[RXRPC]: Add missing select on CRYPTO
David Howells [Fri, 30 Nov 2007 12:06:40 +0000 (23:06 +1100)]
[RXRPC]: Add missing select on CRYPTO

AF_RXRPC uses the crypto services, so should depend on or select CRYPTO.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
17 years agoMerge branch 'fixes-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
Herbert Xu [Fri, 30 Nov 2007 12:29:27 +0000 (23:29 +1100)]
Merge branch 'fixes-davem' of git://git./linux/kernel/git/linville/wireless-2.6

17 years agosh: Support PCI IO access of SH7780 base boards.
Nobuhiro Iwamatsu [Fri, 30 Nov 2007 03:36:13 +0000 (12:36 +0900)]
sh: Support PCI IO access of SH7780 base boards.

The IO access of PCI is not supported in R7780RP and the MS7780SE
board now. The support of the IO access mode of e100 and a lot of IDE
chips becomes possible by fixing the code.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>