IB/mlx4: Adjust delayed work when a dup is observed

[ Upstream commit 785167a114855c5aa75efca97000e405c2cc85bf ]

When scheduling delayed work to clean up the cache, if the entry already
has been scheduled for deletion, we adjust the delay.

Fixes: 3cf69cc8dbeb ("IB/mlx4: Add CM paravirtualization")
Link: https://lore.kernel.org/r/20200803061941.1139994-7-haakon.bugge@oracle.com
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/mlx4: Fix starvation in paravirt mux/demux

[ Upstream commit 7fd1507df7cee9c533f38152fcd1dd769fcac6ce ]

The mlx4 driver will proxy MAD packets through the PF driver. A VM or an
instantiated VF will send its MAD packets to the PF driver using
loop-back. The PF driver will be informed by an interrupt, but defer the
handling and polling of CQEs to a worker thread running on an ordered
work-queue.

Consider the following scenario: the VMs will in short proximity in time,
for example due to a network event, send many MAD packets to the PF
driver. Lets say there are K VMs, each sending N packets.

The interrupt from the first VM will start the worker thread, which will
poll N CQEs. A common case here is where the PF driver will multiplex the
packets received from the VMs out on the wire QP.

But before the wire QP has returned a send CQE and associated interrupt,
the other K - 1 VMs have sent their N packets as well.

The PF driver has to multiplex K * N packets out on the wire QP. But the
send-queue on the wire QP has a finite capacity.

So, in this scenario, if K * N is larger than the send-queue capacity of
the wire QP, we will get MAD packets dropped on the floor with this
dynamic debug message:

mlx4_ib_multiplex_mad: failed sending GSI to wire on behalf of slave 2 (-11)

and this despite the fact that the wire send-queue could have capacity,
but the PF driver isn't aware, because the wire send CQEs have not yet
been polled.

We can also have a similar scenario inbound, with a wire recv-queue larger
than the tunnel QP's send-queue. If many remote peers send MAD packets to
the very same VM, the tunnel send-queue destined to the VM could allegedly
be construed to be full by the PF driver.

This starvation is fixed by introducing separate work queues for the wire
QPs vs. the tunnel QPs.

With this fix, using a dual ported HCA, 8 VFs instantiated, we could run
cmtime on each of the 18 interfaces towards a similar configured peer,
each cmtime instance with 800 QPs (all in all 14400 QPs) without a single
CM packet getting lost.

Fixes: 3cf69cc8dbeb ("IB/mlx4: Add CM paravirtualization")
Link: https://lore.kernel.org/r/20200803061941.1139994-5-haakon.bugge@oracle.com
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mm, oom_adj: don't loop through tasks in __set_oom_adj when not necessary

[ Upstream commit 67197a4f28d28d0b073ab0427b03cb2ee5382578 ]

Currently __set_oom_adj loops through all processes in the system to keep
oom_score_adj and oom_score_adj_min in sync between processes sharing
their mm.  This is done for any task with more that one mm_users, which
includes processes with multiple threads (sharing mm and signals).
However for such processes the loop is unnecessary because their signal
structure is shared as well.

Android updates oom_score_adj whenever a tasks changes its role
(background/foreground/...) or binds to/unbinds from a service, making it
more/less important.  Such operation can happen frequently.  We noticed
that updates to oom_score_adj became more expensive and after further
investigation found out that the patch mentioned in "Fixes" introduced a
regression.  Using Pixel 4 with a typical Android workload, write time to
oom_score_adj increased from ~3.57us to ~362us.  Moreover this regression
linearly depends on the number of multi-threaded processes running on the
system.

Mark the mm with a new MMF_MULTIPROCESS flag bit when task is created with
(CLONE_VM && !CLONE_THREAD && !CLONE_VFORK).  Change __set_oom_adj to use
MMF_MULTIPROCESS instead of mm_users to decide whether oom_score_adj
update should be synchronized between multiple processes.  To prevent
races between clone() and __set_oom_adj(), when oom_score_adj of the
process being cloned might be modified from userspace, we use
oom_adj_mutex.  Its scope is changed to global.

The combination of (CLONE_VM && !CLONE_THREAD) is rarely used except for
the case of vfork().  To prevent performance regressions of vfork(), we
skip taking oom_adj_mutex and setting MMF_MULTIPROCESS when CLONE_VFORK is
specified.  Clearing the MMF_MULTIPROCESS flag (when the last process
sharing the mm exits) is left out of this patch to keep it simple and
because it is believed that this threading model is rare.  Should there
ever be a need for optimizing that case as well, it can be done by hooking
into the exit path, likely following the mm_update_next_owner pattern.

With the combination of (CLONE_VM && !CLONE_THREAD && !CLONE_VFORK) being
quite rare, the regression is gone after the change is applied.

[surenb@google.com: v3]
Link: https://lkml.kernel.org/r/20200902012558.2335613-1-surenb@google.com
Fixes: 44a70adec910 ("mm, oom_adj: make sure processes sharing mm have same view of oom_score_adj")
Reported-by: Tim Murray <timmurray@google.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Eugene Syromiatnikov <esyr@redhat.com>
Cc: Christian Kellner <christian@kellner.me>
Cc: Adrian Reber <areber@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Bernd Edlinger <bernd.edlinger@hotmail.de>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Yafang Shao <laoar.shao@gmail.com>
Link: https://lkml.kernel.org/r/20200824153036.3201505-1-surenb@google.com
Debugged-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mm/memcg: fix device private memcg accounting

[ Upstream commit 9a137153fc8798a89d8fce895cd0a06ea5b8e37c ]

The code in mc_handle_swap_pte() checks for non_swap_entry() and returns
NULL before checking is_device_private_entry() so device private pages are
never handled.  Fix this by checking for non_swap_entry() after handling
device private swap PTEs.

I assume the memory cgroup accounting would be off somehow when moving
a process to another memory cgroup.  Currently, the device private page
is charged like a normal anonymous page when allocated and is uncharged
when the page is freed so I think that path is OK.

Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Link: https://lkml.kernel.org/r/20201009215952.2726-1-rcampbell@nvidia.com
xFixes: c733a82874a7 ("mm/memcontrol: support MEMORY_DEVICE_PRIVATE")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: korina: fix kfree of rx/tx descriptor array

[ Upstream commit 3af5f0f5c74ecbaf757ef06c3f80d56751277637 ]

kmalloc returns KSEG0 addresses so convert back from KSEG1
in kfree. Also make sure array is freed when the driver is
unloaded from the kernel.

Fixes: ef11291bcd5f ("Add support the Korina (IDT RC32434) Ethernet MAC")
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mwifiex: fix double free

[ Upstream commit 53708f4fd9cfe389beab5c8daa763bcd0e0b4aef ]

clang static analysis reports this problem:

sdio.c:2403:3: warning: Attempt to free released memory
        kfree(card->mpa_rx.buf);
        ^~~~~~~~~~~~~~~~~~~~~~~

When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again.  If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().

So set both pointers to NULL when they are freed.

Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()

[ Upstream commit 38b2db564d9ab7797192ef15d7aade30633ceeae ]

The be_fill_queue() function can only fail when "eq_vaddress" is NULL and
since it's non-NULL here that means the function call can't fail.  But
imagine if it could, then in that situation we would want to store the
"paddr" so that dma memory can be released.

Link: https://lore.kernel.org/r/20200928091300.GD377727@mwanda
Fixes: bfead3b2cb46 ("[SCSI] be2iscsi: Adding msix and mcc_rings V3")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: dwc2: Fix INTR OUT transfers in DDMA mode.

[ Upstream commit b2c586eb07efab982419f32b7c3bd96829bc8bcd ]

In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet
corresponds to single descriptor.

Descriptor limit set to mps and desc chain limit set to mps *
MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate
transfer size should be considered correction value for each descriptor.

In start request function, if "continue" is true then dma buffer address
should be incremmented by offset for all type of transfers, not only for
Control DATA_OUT transfers.

Fixes: cf77b5fb9b394 ("usb: dwc2: gadget: Transfer length limit checking for DDMA")
Fixes: e02f9aa6119e0 ("usb: dwc2: gadget: EP 0 specific DDMA programming")
Fixes: aa3e8bc81311e ("usb: dwc2: gadget: DDMA transfer start and complete")

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nl80211: fix non-split wiphy information

[ Upstream commit ab10c22bc3b2024f0c9eafa463899a071eac8d97 ]

When dumping wiphy information, we try to split the data into
many submessages, but for old userspace we still support the
old mode where this doesn't happen.

However, in this case we were not resetting our state correctly
and dumping multiple messages for each wiphy, which would have
broken such older userspace.

This was broken pretty much immediately afterwards because it
only worked in the original commit where non-split dumps didn't
have any more data than split dumps...

Fixes: fe1abafd942f ("nl80211: re-add channel width and extended capa advertising")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200928130717.3e6d9c6bada2.Ie0f151a8d0d00a8e1e18f6a8c9244dd02496af67@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: u_ether: enable qmult on SuperSpeed Plus as well

[ Upstream commit 4eea21dc67b0c6ba15ae41b1defa113a680a858e ]

The u_ether driver has a qmult setting that multiplies the
transmit queue length (which by default is 2).

The intent is that it should be enabled at high/super speed, but
because the code does not explicitly check for USB_SUPER_PLUS,
it is disabled at that speed.

Fix this by ensuring that the queue multiplier is enabled for any
wired link at high speed or above. Using >= for USB_SPEED_*
constants seems correct because it is what the gadget_is_xxxspeed
functions do.

The queue multiplier substantially helps performance at higher
speeds. On a direct SuperSpeed Plus link to a Linux laptop,
iperf3 single TCP stream:

Before (qmult=1): 1.3 Gbps
After  (qmult=5): 3.2 Gbps

Fixes: 04617db7aa68 ("usb: gadget: add SS descriptors to Ethernet gadget")
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: f_ncm: fix ncm_bitrate for SuperSpeed and above.

[ Upstream commit 986499b1569af980a819817f17238015b27793f6 ]

Currently, SuperSpeed NCM gadgets report a speed of 851 Mbps
in USB_CDC_NOTIFY_SPEED_CHANGE. But the calculation appears to
assume 16 packets per microframe, and USB 3 and above no longer
use microframes.

Maximum speed is actually much higher. On a direct connection,
theoretical throughput is at most 3.86 Gbps for gen1x1 and
9.36 Gbps for gen2x1, and I have seen gadget->host iperf
throughput of >2 Gbps for gen1x1 and >4 Gbps for gen2x1.

Unfortunately the ConnectionSpeedChange defined in the CDC spec
only uses 32-bit values, so we can't report accurate numbers for
10Gbps and above. So, report 3.75Gbps for SuperSpeed (which is
roughly maximum theoretical performance) and 4.25Gbps for
SuperSpeed Plus (which is close to the maximum that we can report
in a 32-bit unsigned integer).

This results in:

[50879.191272] cdc_ncm 2-2:1.0 enx228b127e050c: renamed from usb0
[50879.234778] cdc_ncm 2-2:1.0 enx228b127e050c: 3750 mbit/s downlink 3750 mbit/s uplink

on SuperSpeed and:

[50798.434527] cdc_ncm 8-2:1.0 enx228b127e050c: renamed from usb0
[50798.524278] cdc_ncm 8-2:1.0 enx228b127e050c: 4250 mbit/s downlink 4250 mbit/s uplink

on SuperSpeed Plus.

Fixes: 1650113888fe ("usb: gadget: f_ncm: add SuperSpeed descriptors for CDC NCM")
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: split a print to avoid a WARNING in ROC

[ Upstream commit 903b3f9badf1d54f77b468b96706dab679b45b14 ]

A print in the remain on channel code was too long and caused
a WARNING, split it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: dc28e12f2125 ("iwlwifi: mvm: ROC: Extend the ROC max delay duration & limit ROC duration")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930102759.58d57c0bdc68.Ib06008665e7bf1199c360aa92691d9c74fb84990@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: sm501: Fix leaks in probe()

[ Upstream commit 8ce24f8967df2836b4557a23e74dc4bb098249f1 ]

This code should clean up if sm501_init_dev() fails.

Fixes: b6d6454fdb66 ("[PATCH] mfd: SM501 core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: enic: Cure the enic api locking trainwreck

[ Upstream commit a53b59ece86c86d16d12ccdaa1ad0c78250a9d96 ]

enic_dev_wait() has a BUG_ON(in_interrupt()).

Chasing the callers of enic_dev_wait() revealed the gems of enic_reset()
and enic_tx_hang_reset() which are both invoked through work queues in
order to be able to call rtnl_lock(). So far so good.

After locking rtnl both functions acquire enic::enic_api_lock which
serializes against the (ab)use from infiniband. This is where the
trainwreck starts.

enic::enic_api_lock is a spin_lock() which implicitly disables preemption,
but both functions invoke a ton of functions under that lock which can
sleep. The BUG_ON(in_interrupt()) does not trigger in that case because it
can't detect the preempt disabled condition.

This clearly has never been tested with any of the mandatory debug options
for 7+ years, which would have caught that for sure.

Cure it by adding a enic_api_busy member to struct enic, which is modified
and evaluated with enic::enic_api_lock held.

If enic_api_devcmd_proxy_by_index() observes enic::enic_api_busy as true,
it drops enic::enic_api_lock and busy waits for enic::enic_api_busy to
become false.

It would be smarter to wait for a completion of that busy period, but
enic_api_devcmd_proxy_by_index() is called with other spin locks held which
obviously can't sleep.

Remove the BUG_ON(in_interrupt()) check as well because it's incomplete and
with proper debugging enabled the problem would have been caught from the
debug checks in schedule_timeout().

Fixes: 0b038566c0ea ("drivers/net: enic: Add an interface for USNIC to interact with firmware")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qtnfmac: fix resource leaks on unsupported iftype error return path

[ Upstream commit 63f6982075d890d7563e2469643f05a37d193f01 ]

Currently if an unsupported iftype is detected the error return path
does not free the cmd_skb leading to a resource leak. Fix this by
free'ing cmd_skb.

Addresses-Coverity: ("Resource leak")
Fixes: 805b28c05c8e ("qtnfmac: prepare for AP_VLAN interface type support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925132224.21638-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: hid-input: fix stylus battery reporting

[ Upstream commit 505f394fa239cecb76d916aa858f87ed7ea7fde4 ]

With commit 4f3882177240 hid-input started clearing of "ignored" usages
to avoid using garbage that might have been left in them. However
"battery strength" usages should not be ignored, as we do want to
use them.

Fixes: 4f3882177240 ("HID: hid-input: clear unmapped usages")
Reported-by: Kenneth Albanowski <kenalba@google.com>
Tested-by: Kenneth Albanowski <kenalba@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

quota: clear padding in v2r1_mem2diskdqb()

[ Upstream commit 3d3dc274ce736227e3197868ff749cff2f175f63 ]

Freshly allocated memory contains garbage, better make sure
to init all struct v2r1_disk_dqblk fields to avoid KMSAN report:

BUG: KMSAN: uninit-value in qtree_entry_unused+0x137/0x1b0 fs/quota/quota_tree.c:218
CPU: 0 PID: 23373 Comm: syz-executor.1 Not tainted 5.9.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x21c/0x280 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:122
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:219
 qtree_entry_unused+0x137/0x1b0 fs/quota/quota_tree.c:218
 v2r1_mem2diskdqb+0x43d/0x710 fs/quota/quota_v2.c:285
 qtree_write_dquot+0x226/0x870 fs/quota/quota_tree.c:394
 v2_write_dquot+0x1ad/0x280 fs/quota/quota_v2.c:333
 dquot_commit+0x4af/0x600 fs/quota/dquot.c:482
 ext4_write_dquot fs/ext4/super.c:5934 [inline]
 ext4_mark_dquot_dirty+0x4d8/0x6a0 fs/ext4/super.c:5985
 mark_dquot_dirty fs/quota/dquot.c:347 [inline]
 mark_all_dquot_dirty fs/quota/dquot.c:385 [inline]
 dquot_alloc_inode+0xc05/0x12b0 fs/quota/dquot.c:1755
 __ext4_new_inode+0x8204/0x9d70 fs/ext4/ialloc.c:1155
 ext4_tmpfile+0x41a/0x850 fs/ext4/namei.c:2686
 vfs_tmpfile+0x2a2/0x570 fs/namei.c:3283
 do_tmpfile fs/namei.c:3316 [inline]
 path_openat+0x4035/0x6a90 fs/namei.c:3359
 do_filp_open+0x2b8/0x710 fs/namei.c:3395
 do_sys_openat2+0xa88/0x1140 fs/open.c:1168
 do_sys_open fs/open.c:1184 [inline]
 __do_compat_sys_openat fs/open.c:1242 [inline]
 __se_compat_sys_openat+0x2a4/0x310 fs/open.c:1240
 __ia32_compat_sys_openat+0x56/0x70 fs/open.c:1240
 do_syscall_32_irqs_on arch/x86/entry/common.c:80 [inline]
 __do_fast_syscall_32+0x129/0x180 arch/x86/entry/common.c:139
 do_fast_syscall_32+0x6a/0xc0 arch/x86/entry/common.c:162
 do_SYSENTER_32+0x73/0x90 arch/x86/entry/common.c:205
 entry_SYSENTER_compat_after_hwframe+0x4d/0x5c
RIP: 0023:0xf7ff4549
Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 002b:00000000f55cd0cc EFLAGS: 00000296 ORIG_RAX: 0000000000000127
RAX: ffffffffffffffda RBX: 00000000ffffff9c RCX: 0000000020000000
RDX: 0000000000410481 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:143 [inline]
 kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:126
 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:80
 slab_alloc_node mm/slub.c:2907 [inline]
 slab_alloc mm/slub.c:2916 [inline]
 __kmalloc+0x2bb/0x4b0 mm/slub.c:3982
 kmalloc include/linux/slab.h:559 [inline]
 getdqbuf+0x56/0x150 fs/quota/quota_tree.c:52
 qtree_write_dquot+0xf2/0x870 fs/quota/quota_tree.c:378
 v2_write_dquot+0x1ad/0x280 fs/quota/quota_v2.c:333
 dquot_commit+0x4af/0x600 fs/quota/dquot.c:482
 ext4_write_dquot fs/ext4/super.c:5934 [inline]
 ext4_mark_dquot_dirty+0x4d8/0x6a0 fs/ext4/super.c:5985
 mark_dquot_dirty fs/quota/dquot.c:347 [inline]
 mark_all_dquot_dirty fs/quota/dquot.c:385 [inline]
 dquot_alloc_inode+0xc05/0x12b0 fs/quota/dquot.c:1755
 __ext4_new_inode+0x8204/0x9d70 fs/ext4/ialloc.c:1155
 ext4_tmpfile+0x41a/0x850 fs/ext4/namei.c:2686
 vfs_tmpfile+0x2a2/0x570 fs/namei.c:3283
 do_tmpfile fs/namei.c:3316 [inline]
 path_openat+0x4035/0x6a90 fs/namei.c:3359
 do_filp_open+0x2b8/0x710 fs/namei.c:3395
 do_sys_openat2+0xa88/0x1140 fs/open.c:1168
 do_sys_open fs/open.c:1184 [inline]
 __do_compat_sys_openat fs/open.c:1242 [inline]
 __se_compat_sys_openat+0x2a4/0x310 fs/open.c:1240
 __ia32_compat_sys_openat+0x56/0x70 fs/open.c:1240
 do_syscall_32_irqs_on arch/x86/entry/common.c:80 [inline]
 __do_fast_syscall_32+0x129/0x180 arch/x86/entry/common.c:139
 do_fast_syscall_32+0x6a/0xc0 arch/x86/entry/common.c:162
 do_SYSENTER_32+0x73/0x90 arch/x86/entry/common.c:205
 entry_SYSENTER_compat_after_hwframe+0x4d/0x5c

Fixes: 498c60153ebb ("quota: Implement quota format with 64-bit space and inode limits")
Link: https://lore.kernel.org/r/20200924183619.4176790-1-edumazet@google.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jan Kara <jack@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: dwc2: Fix parameter type in function pointer prototype

[ Upstream commit 362b9398c962c9ec563653444e15ef9032ef3a90 ]

When booting up on a Raspberry Pi 4 with Control Flow Integrity checking
enabled, the following warning/panic happens:

[    1.626435] CFI failure (target: dwc2_set_bcm_params+0x0/0x4):
[    1.632408] WARNING: CPU: 0 PID: 32 at kernel/cfi.c:30 __cfi_check_fail+0x54/0x5c
[    1.640021] Modules linked in:
[    1.643137] CPU: 0 PID: 32 Comm: kworker/0:1 Not tainted 5.8.0-rc6-next-20200724-00051-g89ba619726de #1
[    1.652693] Hardware name: Raspberry Pi 4 Model B Rev 1.2 (DT)
[    1.658637] Workqueue: events deferred_probe_work_func
[    1.663870] pstate: 60000005 (nZCv daif -PAN -UAO BTYPE=--)
[    1.669542] pc : __cfi_check_fail+0x54/0x5c
[    1.673798] lr : __cfi_check_fail+0x54/0x5c
[    1.678050] sp : ffff8000102bbaa0
[    1.681419] x29: ffff8000102bbaa0 x28: ffffab09e21c7000
[    1.686829] x27: 0000000000000402 x26: ffff0000f6e7c228
[    1.692238] x25: 00000000fb7cdb0d x24: 0000000000000005
[    1.697647] x23: ffffab09e2515000 x22: ffffab09e069a000
[    1.703055] x21: 4c550309df1cf4c1 x20: ffffab09e2433c60
[    1.708462] x19: ffffab09e160dc50 x18: ffff0000f6e8cc78
[    1.713870] x17: 0000000000000041 x16: ffffab09e0bce6f8
[    1.719278] x15: ffffab09e1c819b7 x14: 0000000000000003
[    1.724686] x13: 00000000ffffefff x12: 0000000000000000
[    1.730094] x11: 0000000000000000 x10: 00000000ffffffff
[    1.735501] x9 : c932f7abfc4bc600 x8 : c932f7abfc4bc600
[    1.740910] x7 : 077207610770075f x6 : ffff0000f6c38f00
[    1.746317] x5 : 0000000000000000 x4 : 0000000000000000
[    1.751723] x3 : 0000000000000000 x2 : 0000000000000000
[    1.757129] x1 : ffff8000102bb7d8 x0 : 0000000000000032
[    1.762539] Call trace:
[    1.765030]  __cfi_check_fail+0x54/0x5c
[    1.768938]  __cfi_check+0x5fa6c/0x66afc
[    1.772932]  dwc2_init_params+0xd74/0xd78
[    1.777012]  dwc2_driver_probe+0x484/0x6ec
[    1.781180]  platform_drv_probe+0xb4/0x100
[    1.785350]  really_probe+0x228/0x63c
[    1.789076]  driver_probe_device+0x80/0xc0
[    1.793247]  __device_attach_driver+0x114/0x160
[    1.797857]  bus_for_each_drv+0xa8/0x128
[    1.801851]  __device_attach.llvm.14901095709067289134+0xc0/0x170
[    1.808050]  bus_probe_device+0x44/0x100
[    1.812044]  deferred_probe_work_func+0x78/0xb8
[    1.816656]  process_one_work+0x204/0x3c4
[    1.820736]  worker_thread+0x2f0/0x4c4
[    1.824552]  kthread+0x174/0x184
[    1.827837]  ret_from_fork+0x10/0x18

CFI validates that all indirect calls go to a function with the same
exact function pointer prototype. In this case, dwc2_set_bcm_params
is the target, which has a parameter of type 'struct dwc2_hsotg *',
but it is being implicitly cast to have a parameter of type 'void *'
because that is the set_params function pointer prototype. Make the
function pointer protoype match the definitions so that there is no
more violation.

Fixes: 7de1debcd2de ("usb: dwc2: Remove platform static params")
Link: https://github.com/ClangBuiltLinux/linux/issues/1107
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: seq: oss: Avoid mutex lock for a long-time ioctl

[ Upstream commit 2759caad2600d503c3b0ed800e7e03d2cd7a4c05 ]

Recently we applied a fix to cover the whole OSS sequencer ioctls with
the mutex for dealing with the possible races.  This works fine in
general, but in theory, this may lead to unexpectedly long stall if an
ioctl like SNDCTL_SEQ_SYNC is issued and an event with the far future
timestamp was queued.

For fixing such a potential stall, this patch changes the mutex lock
applied conditionally excluding such an ioctl command.  Also, change
the mutex_lock() with the interruptible version for user to allow
escaping from the big-hammer mutex.

Fixes: 80982c7e834e ("ALSA: seq: oss: Serialize ioctls")
Suggested-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20200922083856.28572-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: mic: scif: Fix error handling path

[ Upstream commit a81072a9c0ae734b7889929b0bc070fe3f353f0e ]

Inside __scif_pin_pages(), when map_flags != SCIF_MAP_KERNEL it
will call pin_user_pages_fast() to map nr_pages. However,
pin_user_pages_fast() might fail with a return value -ERRNO.

The return value is stored in pinned_pages->nr_pages. which in
turn is passed to unpin_user_pages(), which expects
pinned_pages->nr_pages >=0, else disaster.

Fix this by assigning pinned_pages->nr_pages to 0 if
pin_user_pages_fast() returns -ERRNO.

Fixes: ba612aa8b487 ("misc: mic: SCIF memory registration and unregistration")
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Link: https://lore.kernel.org/r/1600570295-29546-1-git-send-email-jrdr.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath6kl: wmi: prevent a shift wrapping bug in ath6kl_wmi_delete_pstream_cmd()

[ Upstream commit 6a950755cec1a90ddaaff3e4acb5333617441c32 ]

The "tsid" is a user controlled u8 which comes from debugfs.  Values
more than 15 are invalid because "active_tsids" is a 16 bit variable.
If the value of "tsid" is more than 31 then that leads to a shift
wrapping bug.

Fixes: 8fffd9e5ec9e ("ath6kl: Implement support for QOS-enable and QOS-disable from userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918142732.GA909725@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: mcp23s08: Fix mcp23x17 precious range

[ Upstream commit b9b7fb29433b906635231d0a111224efa009198c ]

On page 23 of the datasheet [0] it says "The register remains unchanged
until the interrupt is cleared via a read of INTCAP or GPIO." Include
INTCAPA and INTCAPB registers in precious range, so that they aren't
accidentally cleared when we read via debugfs.

[0] https://ww1.microchip.com/downloads/en/DeviceDoc/20001952C.pdf

Fixes: 8f38910ba4f6 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-3-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: mcp23s08: Fix mcp23x17_regmap initialiser

[ Upstream commit b445f6237744df5e8d4f56f8733b2108c611220a ]

The mcp23x17_regmap is initialised with structs named "mcp23x16".
However, the mcp23s08 driver doesn't support the MCP23016 device yet, so
this appears to be a typo.

Fixes: 8f38910ba4f6 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-2-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: roccat: add bounds checking in kone_sysfs_write_settings()

[ Upstream commit d4f98dbfe717490e771b6e701904bfcf4b4557f0 ]

This code doesn't check if "settings->startup_profile" is within bounds
and that could result in an out of bounds array access.  What the code
does do is it checks if the settings can be written to the firmware, so
it's possible that the firmware has a bounds check?  It's safer and
easier to verify when the bounds checking is done in the kernel.

Fixes: 14bf62cde794 ("HID: add driver for Roccat Kone gaming mouse")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: fbdev: sis: fix null ptr dereference

[ Upstream commit ad6f93e9cd56f0b10e9b22e3e137d17a1a035242 ]

Clang static analysis reports this representative error

init.c:2501:18: warning: Array access (from variable 'queuedata') results
  in a null pointer dereference
      templ |= ((queuedata[i] & 0xc0) << 3);

This is the problem block of code

   if(ModeNo > 0x13) {
      ...
      if(SiS_Pr->ChipType == SIS_730) {
 queuedata = &FQBQData730[0];
      } else {
 queuedata = &FQBQData[0];
      }
   } else {

   }

queuedata is not set in the else block

Reviewing the old code, the arrays FQBQData730 and FQBQData were
used directly.

So hoist the setting of queuedata out of the if-else block.

Fixes: 544393fe584d ("[PATCH] sisfb update")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805145208.17727-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: fbdev: vga16fb: fix setting of pixclock because a pass-by-value error

[ Upstream commit c72fab81ceaa54408b827a2f0486d9a0f4be34cf ]

The pixclock is being set locally because it is being passed as a
pass-by-value argument rather than pass-by-reference, so the computed
pixclock is never being set in var->pixclock. Fix this by passing
by reference.

[This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git ]

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
[b.zolnierkie: minor patch summary fixup]
[b.zolnierkie: removed "Fixes:" tag (not in upstream tree)]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200723170227.996229-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drivers/virt/fsl_hypervisor: Fix error handling path

[ Upstream commit 7f360bec37857bfd5a48cef21d86f58a09a3df63 ]

First, when memory allocation for sg_list_unaligned failed, there
is a bug of calling put_pages() as we haven't pinned any pages.

Second, if get_user_pages_fast() failed we should unpin num_pinned
pages.

This will address both.

As part of these changes, minor update in documentation.

Fixes: 6db7199407ca ("drivers/virt: introduce Freescale hypervisor management driver")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Link: https://lore.kernel.org/r/1598995271-6755-1-git-send-email-jrdr.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: lpss: Add range limit check for the base_unit register value

[ Upstream commit ef9f60daab309558c8bb3e086a9a11ee40bd6061 ]

When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.

But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.

When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:

base_unit &= (base_unit_range - 1);

But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.

This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).

Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: lpss: Fix off by one error in base_unit math in pwm_lpss_prepare()

[ Upstream commit 181f4d2f44463fe09fe4df02e03095cb87151c29 ]

According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.

So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.

This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().

Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.

Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

pty: do tty_flip_buffer_push without port->lock in pty_write

[ Upstream commit 71a174b39f10b4b93223d374722aa894b5d8a82e ]

b6da31b2c07c "tty: Fix data race in tty_insert_flip_string_fixed_flag"
puts tty_flip_buffer_push under port->lock introducing the following
possible circular locking dependency:

[30129.876566] ======================================================
[30129.876566] WARNING: possible circular locking dependency detected
[30129.876567] 5.9.0-rc2+ #3 Tainted: G S      W
[30129.876568] ------------------------------------------------------
[30129.876568] sysrq.sh/1222 is trying to acquire lock:
[30129.876569] ffffffff92c39480 (console_owner){....}-{0:0}, at: console_unlock+0x3fe/0xa90

[30129.876572] but task is already holding lock:
[30129.876572] ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca

[30129.876576] which lock already depends on the new lock.

[30129.876577] the existing dependency chain (in reverse order) is:

[30129.876578] -> #3 (&pool->lock/1){-.-.}-{2:2}:
[30129.876581]        _raw_spin_lock+0x30/0x70
[30129.876581]        __queue_work+0x1a3/0x10f0
[30129.876582]        queue_work_on+0x78/0x80
[30129.876582]        pty_write+0x165/0x1e0
[30129.876583]        n_tty_write+0x47f/0xf00
[30129.876583]        tty_write+0x3d6/0x8d0
[30129.876584]        vfs_write+0x1a8/0x650

[30129.876588] -> #2 (&port->lock#2){-.-.}-{2:2}:
[30129.876590]        _raw_spin_lock_irqsave+0x3b/0x80
[30129.876591]        tty_port_tty_get+0x1d/0xb0
[30129.876592]        tty_port_default_wakeup+0xb/0x30
[30129.876592]        serial8250_tx_chars+0x3d6/0x970
[30129.876593]        serial8250_handle_irq.part.12+0x216/0x380
[30129.876593]        serial8250_default_handle_irq+0x82/0xe0
[30129.876594]        serial8250_interrupt+0xdd/0x1b0
[30129.876595]        __handle_irq_event_percpu+0xfc/0x850

[30129.876602] -> #1 (&port->lock){-.-.}-{2:2}:
[30129.876605]        _raw_spin_lock_irqsave+0x3b/0x80
[30129.876605]        serial8250_console_write+0x12d/0x900
[30129.876606]        console_unlock+0x679/0xa90
[30129.876606]        register_console+0x371/0x6e0
[30129.876607]        univ8250_console_init+0x24/0x27
[30129.876607]        console_init+0x2f9/0x45e

[30129.876609] -> #0 (console_owner){....}-{0:0}:
[30129.876611]        __lock_acquire+0x2f70/0x4e90
[30129.876612]        lock_acquire+0x1ac/0xad0
[30129.876612]        console_unlock+0x460/0xa90
[30129.876613]        vprintk_emit+0x130/0x420
[30129.876613]        printk+0x9f/0xc5
[30129.876614]        show_pwq+0x154/0x618
[30129.876615]        show_workqueue_state.cold.55+0x193/0x6ca
[30129.876615]        __handle_sysrq+0x244/0x460
[30129.876616]        write_sysrq_trigger+0x48/0x4a
[30129.876616]        proc_reg_write+0x1a6/0x240
[30129.876617]        vfs_write+0x1a8/0x650

[30129.876619] other info that might help us debug this:

[30129.876620] Chain exists of:
[30129.876621]   console_owner --> &port->lock#2 --> &pool->lock/1

[30129.876625]  Possible unsafe locking scenario:

[30129.876626]        CPU0                    CPU1
[30129.876626]        ----                    ----
[30129.876627]   lock(&pool->lock/1);
[30129.876628]                                lock(&port->lock#2);
[30129.876630]                                lock(&pool->lock/1);
[30129.876631]   lock(console_owner);

[30129.876633]  *** DEADLOCK ***

[30129.876634] 5 locks held by sysrq.sh/1222:
[30129.876634]  #0: ffff8881d3ce0470 (sb_writers#3){.+.+}-{0:0}, at: vfs_write+0x359/0x650
[30129.876637]  #1: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: __handle_sysrq+0x4d/0x460
[30129.876640]  #2: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: show_workqueue_state+0x5/0xf0
[30129.876642]  #3: ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca
[30129.876645]  #4: ffffffff92c39980 (console_lock){+.+.}-{0:0}, at: vprintk_emit+0x123/0x420

[30129.876648] stack backtrace:
[30129.876649] CPU: 3 PID: 1222 Comm: sysrq.sh Tainted: G S      W         5.9.0-rc2+ #3
[30129.876649] Hardware name: Intel Corporation 2012 Client Platform/Emerald Lake 2, BIOS ACRVMBY1.86C.0078.P00.1201161002 01/16/2012
[30129.876650] Call Trace:
[30129.876650]  dump_stack+0x9d/0xe0
[30129.876651]  check_noncircular+0x34f/0x410
[30129.876653]  __lock_acquire+0x2f70/0x4e90
[30129.876656]  lock_acquire+0x1ac/0xad0
[30129.876658]  console_unlock+0x460/0xa90
[30129.876660]  vprintk_emit+0x130/0x420
[30129.876660]  printk+0x9f/0xc5
[30129.876661]  show_pwq+0x154/0x618
[30129.876662]  show_workqueue_state.cold.55+0x193/0x6ca
[30129.876664]  __handle_sysrq+0x244/0x460
[30129.876665]  write_sysrq_trigger+0x48/0x4a
[30129.876665]  proc_reg_write+0x1a6/0x240
[30129.876666]  vfs_write+0x1a8/0x650

It looks like the commit was aimed to protect tty_insert_flip_string and
there is no need for tty_flip_buffer_push to be under this lock.

Fixes: b6da31b2c07c ("tty: Fix data race in tty_insert_flip_string_fixed_flag")
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200902120045.3693075-1-asavkov@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: hvcs: Don't NULL tty->driver_data until hvcs_cleanup()

[ Upstream commit 63ffcbdad738e3d1c857027789a2273df3337624 ]

The code currently NULLs tty->driver_data in hvcs_close() with the
intent of informing the next call to hvcs_open() that device needs to be
reconfigured. However, when hvcs_cleanup() is called we copy hvcsd from
tty->driver_data which was previoulsy NULLed by hvcs_close() and our
call to tty_port_put(&hvcsd->port) doesn't actually do anything since
&hvcsd->port ends up translating to NULL by chance. This has the side
effect that when hvcs_remove() is called we have one too many port
references preventing hvcs_destuct_port() from ever being called. This
also prevents us from reusing the /dev/hvcsX node in a future
hvcs_probe() and we can eventually run out of /dev/hvcsX devices.

Fix this by waiting to NULL tty->driver_data in hvcs_cleanup().

Fixes: 27bf7c43a19c ("TTY: hvcs, add tty install")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Link: https://lore.kernel.org/r/20200820234643.70412-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: serial: earlycon dependency

[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ]

parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin

Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

VMCI: check return value of get_user_pages_fast() for errors

[ Upstream commit 90ca6333fd65f318c47bff425e1ea36c0a5539f6 ]

In a couple of places in qp_host_get_user_memory(),
get_user_pages_fast() is called without properly checking for errors. If
e.g. -EFAULT is returned, this negative value will then be passed on to
qp_release_pages(), which expects a u64 as input.

Fix this by only calling qp_release_pages() when we have a positive
number returned.

Fixes: 06164d2b72aa ("VMCI: queue pairs implementation.")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200825164522.412392-1-alex.dewar90@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

backlight: sky81452-backlight: Fix refcount imbalance on error

[ Upstream commit b7a4f80bc316a56d6ec8750e93e66f42431ed960 ]

When of_property_read_u32_array() returns an error code, a
pairing refcount decrement is needed to keep np's refcount
balanced.

Fixes: f705806c9f355 ("backlight: Add support Skyworks SKY81452 backlight driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: csiostor: Fix wrong return value in csio_hw_prep_fw()

[ Upstream commit 44f4daf8678ae5f08c93bbe70792f90cd88e4649 ]

On an error exit path, a negative error code should be returned instead of
a positive return value.

Link: https://lore.kernel.org/r/20200802111531.5065-1-tianjia.zhang@linux.alibaba.com
Fixes: f40e74ffa3de ("csiostor:firmware upgrade fix")
Cc: Praveen Madhavan <praveenm@chelsio.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: qla4xxx: Fix an error handling path in 'qla4xxx_get_host_stats()'

[ Upstream commit 574918e69720fe62ab3eb42ec3750230c8d16b06 ]

Update the size used in 'dma_free_coherent()' in order to match the one
used in the corresponding 'dma_alloc_coherent()'.

Link: https://lore.kernel.org/r/20200802101527.676054-1-christophe.jaillet@wanadoo.fr
Fixes: 4161cee52df8 ("[SCSI] qla4xxx: Add host statistics support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/gma500: fix error check

[ Upstream commit cdd296cdae1af2d27dae3fcfbdf12c5252ab78cf ]

Reviewing this block of code in cdv_intel_dp_init()

ret = cdv_intel_dp_aux_native_read(gma_encoder, DP_DPCD_REV, ...

cdv_intel_edp_panel_vdd_off(gma_encoder);
if (ret == 0) {
/* if this fails, presume the device is a ghost */
DRM_INFO("failed to retrieve link info, disabling eDP\n");
drm_encoder_cleanup(encoder);
cdv_intel_dp_destroy(connector);
goto err_priv;
} else {

The (ret == 0) is not strict enough.
cdv_intel_dp_aux_native_read() returns > 0 on success
otherwise it is failure.

So change to <=

Fixes: d112a8163f83 ("gma500/cdv: Add eDP support")

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805205911.20927-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mwifiex: Do not use GFP_KERNEL in atomic context

[ Upstream commit d2ab7f00f4321370a8ee14e5630d4349fdacc42e ]

A possible call chain is as follow:
  mwifiex_sdio_interrupt                            (sdio.c)
    --> mwifiex_main_process                        (main.c)
      --> mwifiex_process_cmdresp                   (cmdevt.c)
        --> mwifiex_process_sta_cmdresp             (sta_cmdresp.c)
          --> mwifiex_ret_802_11_scan               (scan.c)
            --> mwifiex_parse_single_response_buf   (scan.c)

'mwifiex_sdio_interrupt()' is an interrupt function.

Also note that 'mwifiex_ret_802_11_scan()' already uses GFP_ATOMIC.

So use GFP_ATOMIC instead of GFP_KERNEL when memory is allocated in
'mwifiex_parse_single_response_buf()'.

Fixes: 7c6fa2a843c5 ("mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API")
or
Fixes: 601216e12c65e ("mwifiex: process RX packets in SDIO IRQ thread directly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200809092906.744621-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

brcmfmac: check ndev pointer

[ Upstream commit 9c9f015bc9f8839831c7ba0a6d731a3853c464e2 ]

Clang static analysis reports this error

brcmfmac/core.c:490:4: warning: Dereference of null pointer
        (*ifp)->ndev->stats.rx_errors++;
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In this block of code

if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && *ifp)
(*ifp)->ndev->stats.rx_errors++;
brcmu_pkt_buf_free_skb(skb);
return -ENODATA;
}

(*ifp)->ndev being NULL is caught as an error
But then it is used to report the error.

So add a check before using it.

Fixes: 91b632803ee4 ("brcmfmac: Use net_device_stats from struct net_device")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802161804.6126-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: qcom: lpass-cpu: fix concurrency issue

[ Upstream commit 753a6e17942f6f425ca622e1610625998312ad89 ]

i2sctl register value is set to 0 during hw_free(). This
impacts any ongoing concurrent session on the same i2s
port. As trigger() stop already resets enable bit to 0,
there is no need of explicit hw_free. Removing it to
fix the issue.

Fixes: 80beab8e1d86 ("ASoC: qcom: Add LPASS CPU DAI driver")
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/1597402388-14112-7-git-send-email-rohitkr@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: qcom: lpass-platform: fix memory leak

[ Upstream commit 5fd188215d4eb52703600d8986b22311099a5940 ]

lpass_pcm_data is never freed. Free it in close
ops to avoid memory leak.

Fixes: 022d00ee0b55 ("ASoC: lpass-platform: Fix broken pcm data usage")
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/1597402388-14112-5-git-send-email-rohitkr@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wcn36xx: Fix reported 802.11n rx_highest rate wcn3660/wcn3680

[ Upstream commit 3b9fb6791e7113679b1eb472e6ce1659e80f5797 ]

Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for
the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here.

This patch fixes the data-rate declared in the 5GHz table.

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680
hardware")

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k: Fix potential out of bounds in ath9k_htc_txcompletion_cb()

[ Upstream commit 2705cd7558e718a7240c64eb0afb2edad5f8c190 ]

The value of "htc_hdr->endpoint_id" comes from skb->data so Smatch marks
it as untrusted so we have to check it before using it as an array
offset.

This is similar to a bug that syzkaller found in commit e4ff08a4d727
("ath9k: Fix use-after-free Write in ath9k_htc_rx_msg") so it is
probably a real issue.

Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141253.GA457408@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath6kl: prevent potential array overflow in ath6kl_add_new_sta()

[ Upstream commit 54f9ab7b870934b70e5a21786d951fbcf663970f ]

The value for "aid" comes from skb->data so Smatch marks it as
untrusted.  If it's invalid then it can result in an out of bounds array
access in ath6kl_add_new_sta().

Fixes: 572e27c00c9d ("ath6kl: Fix AP mode connect event parsing and TIM updates")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141315.GB457408@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: hci_uart: Cancel init work before unregistering

[ Upstream commit 3b799254cf6f481460719023d7a18f46651e5e7f ]

If hci_uart_tty_close() or hci_uart_unregister_device() is called while
hu->init_ready is scheduled, hci_register_dev() could be called after
the hci_uart is torn down. Avoid this by ensuring the work is complete
or canceled before checking the HCI_UART_REGISTERED flag.

Fixes: 9f2aee848fe6 ("Bluetooth: Add delayed init sequence support for UART controllers")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath10k: provide survey info as accumulated data

[ Upstream commit 720e5c03e5cb26d33d97f55192b791bb48478aa5 ]

It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.

example:

  $ iw dev wlan0 survey dump
  Survey data from wlan0
   frequency:                      5180 MHz [in use]
   channel active time:            54995 ms
   channel busy time:              432 ms
   channel receive time:           0 ms
   channel transmit time:          59 ms
  ...

  $ iw dev wlan0 survey dump
  Survey data from wlan0
   frequency:                      5180 MHz [in use]
   channel active time:            32592 ms
   channel busy time:              254 ms
   channel receive time:           0 ms
   channel transmit time:          0 ms
  ...

The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.

Tested-on: QCA9984 hw1.0 10.4-3.5.3-00057
Tested-on: QCA988X hw2.0 10.2.4-1.0-00047
Tested-on: QCA9888 hw2.0 10.4-3.9.0.2-00024
Tested-on: QCA4019 hw1.0 10.4-3.6-00140

Fixes: fa7937e3d5c2 ("ath10k: update bss channel survey information")
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Tested-by: Markus Theil <markus.theil@tu-ilmenau.de>
Tested-by: John Deere <24601deerej@gmail.com>
[sven@narfation.org: adjust commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592232686-28712-1-git-send-email-kvalo@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

regulator: resolve supply after creating regulator

[ Upstream commit aea6cb99703e17019e025aa71643b4d3e0a24413 ]

When creating a new regulator its supply cannot create the sysfs link
because the device is not yet published. Remove early supply resolving
since it will be done later anyway. This makes the following error
disappear and the symlinks get created instead.

  DCDC_REG1: supplied by VSYS
  VSYS: could not add device link regulator.3 err -2

Note: It doesn't fix the problem for bypassed regulators, though.

Fixes: 45389c47526d ("regulator: core: Add early supply resolution for regulators")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/ba09e0a8617ffeeb25cb4affffe6f3149319cef8.1601155770.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: ti-vpe: Fix a missing check and reference count leak

[ Upstream commit 7dae2aaaf432767ca7aa11fa84643a7c2600dbdd ]

pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
And also, when the call of function vpe_runtime_get() failed,
we won't call vpe_runtime_put().
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails
inside vpe_runtime_get().

Fixes: 4571912743ac ("[media] v4l: ti-vpe: Add VPE mem to mem driver")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: s5p-mfc: Fix a reference count leak

[ Upstream commit 78741ce98c2e36188e2343434406b0e0bc50b0e7 ]

pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.

Fixes: c5086f130a77 ("[media] s5p-mfc: Use clock gating only on MFC v5 hardware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: platform: fcp: Fix a reference count leak.

[ Upstream commit 63e36a381d92a9cded97e90d481ee22566557dd1 ]

pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.

Fixes: 6eaafbdb668b ("[media] v4l: rcar-fcp: Keep the coding style consistent")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: tc358743: initialize variable

[ Upstream commit 274cf92d5dff5c2fec1a518078542ffe70d07646 ]

clang static analysis flags this error

tc358743.c:1468:9: warning: Branch condition evaluates
  to a garbage value
        return handled ? IRQ_HANDLED : IRQ_NONE;
               ^~~~~~~
handled should be initialized to false.

Fixes: d747b806abf4 ("[media] tc358743: add direct interrupt handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: mx2_emmaprp: Fix memleak in emmaprp_probe

[ Upstream commit 21d387b8d372f859d9e87fdcc7c3b4a432737f4d ]

When platform_get_irq() fails, we should release
vfd and unregister pcdev->v4l2_dev just like the
subsequent error paths.

Fixes: d4e192cc44914 ("media: mx2_emmaprp: Check for platform_get_irq() error")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cypto: mediatek - fix leaks in mtk_desc_ring_alloc

[ Upstream commit 228d284aac61283cde508a925d666f854b57af63 ]

In the init loop, if an error occurs in function 'dma_alloc_coherent',
then goto the err_cleanup section, after run i--,
in the array ring, the struct mtk_ring with index i will not be released,
causing memory leaks

Fixes: 785e5c616c849 ("crypto: mediatek - Add crypto driver support for some MediaTek chips")
Cc: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Xiaoliang Pang <dawning.pang@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: omap-sham - fix digcnt register handling with export/import

[ Upstream commit 3faf757bad75f3fc1b2736f0431e295a073a7423 ]

Running export/import for hashes in peculiar order (mostly done by
openssl) can mess up the internal book keeping of the OMAP SHA core.
Fix by forcibly writing the correct DIGCNT back to hardware. This issue
was noticed while transitioning to openssl 1.1 support.

Fixes: 0d373d603202 ("crypto: omap-sham - Add OMAP4/AM33XX SHAM Support")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: omap3isp: Fix memleak in isp_probe

[ Upstream commit d8fc21c17099635e8ebd986d042be65a6c6b5bd0 ]

When devm_ioremap_resource() fails, isp should be
freed just like other error paths in isp_probe.

Fixes: 8644cdf972dd6 ("[media] omap3isp: Replace many MMIO regions by two")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Set media controller entity functions

[ Upstream commit d6834b4b58d110814aaf3469e7fd87d34ae5ae81 ]

The media controller core prints a warning when an entity is registered
without a function being set. This affects the uvcvideo driver, as the
warning was added without first addressing the issue in existing
drivers. The problem is harmless, but unnecessarily worries users. Fix
it by mapping UVC entity types to MC entity functions as accurately as
possible using the existing functions.

Fixes: b50bde4e476d ("[media] v4l2-subdev: use MEDIA_ENT_T_UNKNOWN for new subdevs")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: m5mols: Check function pointer in m5mols_sensor_power

[ Upstream commit 52438c4463ac904d14bf3496765e67750766f3a6 ]

clang static analysis reports this error

m5mols_core.c:767:4: warning: Called function pointer
  is null (null dereference) [core.CallAndMessage]
    info->set_power(&client->dev, 0);
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In other places, the set_power ptr is checked.
So add a check.

Fixes: bc125106f8af ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: Revert "media: exynos4-is: Add missed check for pinctrl_lookup_state()"

[ Upstream commit 00d21f325d58567d81d9172096692d0a9ea7f725 ]

The "idle" pinctrl state is optional as documented in the DT binding.
The change introduced by the commit being reverted makes that pinctrl state
mandatory and breaks initialization of the whole media driver, since the
"idle" state is not specified in any mainline dts.

This reverts commit 18ffec750578 ("media: exynos4-is: Add missed check for pinctrl_lookup_state()")
to fix the regression.

Fixes: 18ffec750578 ("media: exynos4-is: Add missed check for pinctrl_lookup_state()")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: tuner-simple: fix regression in simple_set_radio_freq

[ Upstream commit 505bfc2a142f12ce7bc7a878b44abc3496f2e747 ]

clang static analysis reports this problem

tuner-simple.c:714:13: warning: Assigned value is
  garbage or undefined
        buffer[1] = buffer[3];
                  ^ ~~~~~~~~~
In simple_set_radio_freq buffer[3] used to be done
in-function with a switch of tuner type, now done
by a call to simple_radio_bandswitch which has this case

case TUNER_TENA_9533_DI:
case TUNER_YMEC_TVF_5533MF:
tuner_dbg("This tuner doesn't ...
return 0;

which does not set buffer[3].  In the old logic, this case
would have returned 0 from simple_set_radio_freq.

Recover this old behavior by returning an error for this
codition. Since the old simple_set_radio_freq behavior
returned a 0, do the same.

Fixes: c7a9f3aa1e1b ("V4L/DVB (7129): tuner-simple: move device-specific code into three separate functions")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: ixp4xx - Fix the size used in a 'dma_free_coherent()' call

[ Upstream commit f7ade9aaf66bd5599690acf0597df2c0f6cd825a ]

Update the size used in 'dma_free_coherent()' in order to match the one
used in the corresponding 'dma_alloc_coherent()', in 'setup_crypt_desc()'.

Fixes: 81bef0150074 ("crypto: ixp4xx - Hardware crypto support for IXP4xx CPUs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: mediatek - Fix wrong return value in mtk_desc_ring_alloc()

[ Upstream commit 8cbde6c6a6d2b1599ff90f932304aab7e32fce89 ]

In case of memory allocation failure, a negative error code should
be returned.

Fixes: 785e5c616c849 ("crypto: mediatek - Add crypto driver support for some MediaTek chips")
Cc: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: algif_skcipher - EBUSY on aio should be an error

[ Upstream commit 2a05b029c1ee045b886ebf9efef9985ca23450de ]

I removed the MAY_BACKLOG flag on the aio path a while ago but
the error check still incorrectly interpreted EBUSY as success.
This may cause the submitter to wait for a request that will never
complete.

Fixes: dad419970637 ("crypto: algif_skcipher - Do not set...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drivers/perf: xgene_pmu: Fix uninitialized resource struct

[ Upstream commit a76b8236edcf5b785d044b930f9e14ad02b4a484 ]

This splat was reported on newer Fedora kernels booting on certain
X-gene based machines:

 xgene-pmu APMC0D83:00: X-Gene PMU version 3
 Unable to handle kernel read from unreadable memory at virtual \
 address 0000000000004006
 ...
 Call trace:
  string+0x50/0x100
  vsnprintf+0x160/0x750
  devm_kvasprintf+0x5c/0xb4
  devm_kasprintf+0x54/0x60
  __devm_ioremap_resource+0xdc/0x1a0
  devm_ioremap_resource+0x14/0x20
  acpi_get_pmu_hw_inf.isra.0+0x84/0x15c
  acpi_pmu_dev_add+0xbc/0x21c
  acpi_ns_walk_namespace+0x16c/0x1e4
  acpi_walk_namespace+0xb4/0xfc
  xgene_pmu_probe_pmu_dev+0x7c/0xe0
  xgene_pmu_probe.part.0+0x2c0/0x310
  xgene_pmu_probe+0x54/0x64
  platform_drv_probe+0x60/0xb4
  really_probe+0xe8/0x4a0
  driver_probe_device+0xe4/0x100
  device_driver_attach+0xcc/0xd4
  __driver_attach+0xb0/0x17c
  bus_for_each_dev+0x6c/0xb0
  driver_attach+0x30/0x40
  bus_add_driver+0x154/0x250
  driver_register+0x84/0x140
  __platform_driver_register+0x54/0x60
  xgene_pmu_driver_init+0x28/0x34
  do_one_initcall+0x40/0x204
  do_initcalls+0x104/0x144
  kernel_init_freeable+0x198/0x210
  kernel_init+0x20/0x12c
  ret_from_fork+0x10/0x18
 Code: 91000400 110004e1 eb08009f 540000c0 (38646846)
 ---[ end trace f08c10566496a703 ]---

This is due to use of an uninitialized local resource struct in the xgene
pmu driver. The thunderx2_pmu driver avoids this by using the resource list
constructed by acpi_dev_get_resources() rather than using a callback from
that function. The callback in the xgene driver didn't fully initialize
the resource. So get rid of the callback and search the resource list as
done by thunderx2.

Fixes: 832c927d119b ("perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver")
Signed-off-by: Mark Salter <msalter@redhat.com>
Link: https://lore.kernel.org/r/20200915204110.326138-1-msalter@redhat.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/fpu: Allow multiple bits in clearcpuid= parameter

[ Upstream commit 0a4bb5e5507a585532cc413125b921c8546fc39f ]

Commit

  0c2a3913d6f5 ("x86/fpu: Parse clearcpuid= as early XSAVE argument")

changed clearcpuid parsing from __setup() to cmdline_find_option().
While the __setup() function would have been called for each clearcpuid=
parameter on the command line, cmdline_find_option() will only return
the last one, so the change effectively made it impossible to disable
more than one bit.

Allow a comma-separated list of bit numbers as the argument for
clearcpuid to allow multiple bits to be disabled again. Log the bits
being disabled for informational purposes.

Also fix the check on the return value of cmdline_find_option(). It
returns -1 when the option is not found, so testing as a boolean is
incorrect.

Fixes: 0c2a3913d6f5 ("x86/fpu: Parse clearcpuid= as early XSAVE argument")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907213919.2423441-1-nivedita@alum.mit.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>

EDAC/i5100: Fix error handling order in i5100_init_one()

[ Upstream commit 857a3139bd8be4f702c030c8ca06f3fd69c1741a ]

When pci_get_device_func() fails, the driver doesn't need to execute
pci_dev_put(). mci should still be freed, though, to prevent a memory
leak. When pci_enable_device() fails, the error injection PCI device
"einj" doesn't need to be disabled either.

 [ bp: Massage commit message, rename label to "bail_mc_free". ]

Fixes: 52608ba205461 ("i5100_edac: probe for device 19 function 0")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200826121437.31606-1-dinghao.liu@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: algif_aead - Do not set MAY_BACKLOG on the async path

commit cbdad1f246dd98e6c9c32a6e5212337f542aa7e0 upstream.

The async path cannot use MAY_BACKLOG because it is not meant to
block, which is what MAY_BACKLOG does.  On the other hand, both
the sync and async paths can make use of MAY_SLEEP.

Fixes: 83094e5e9e49 ("crypto: af_alg - add async support to...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ima: Don't ignore errors from crypto_shash_update()

commit 60386b854008adc951c470067f90a2d85b5d520f upstream.

Errors returned by crypto_shash_update() are not checked in
ima_calc_boot_aggregate_tfm() and thus can be overwritten at the next
iteration of the loop. This patch adds a check after calling
crypto_shash_update() and returns immediately if the result is not zero.

Cc: stable@vger.kernel.org
Fixes: 3323eec921efd ("integrity: IMA as an integrity service provider")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: SVM: Initialize prev_ga_tag before use

commit f6426ab9c957e97418ac5b0466538792767b1738 upstream.

The function amd_ir_set_vcpu_affinity makes use of the parameter struct
amd_iommu_pi_data.prev_ga_tag to determine if it should delete struct
amd_iommu_pi_data from a list when not running in AVIC mode.

However, prev_ga_tag is initialized only when AVIC is enabled. The non-zero
uninitialized value can cause unintended code path, which ends up making
use of the struct vcpu_svm.ir_list and ir_list_lock without being
initialized (since they are intended only for the AVIC case).

This triggers NULL pointer dereference bug in the function vm_ir_list_del
with the following call trace:

    svm_update_pi_irte+0x3c2/0x550 [kvm_amd]
    ? proc_create_single_data+0x41/0x50
    kvm_arch_irq_bypass_add_producer+0x40/0x60 [kvm]
    __connect+0x5f/0xb0 [irqbypass]
    irq_bypass_register_producer+0xf8/0x120 [irqbypass]
    vfio_msi_set_vector_signal+0x1de/0x2d0 [vfio_pci]
    vfio_msi_set_block+0x77/0xe0 [vfio_pci]
    vfio_pci_set_msi_trigger+0x25c/0x2f0 [vfio_pci]
    vfio_pci_set_irqs_ioctl+0x88/0xb0 [vfio_pci]
    vfio_pci_ioctl+0x2ea/0xed0 [vfio_pci]
    ? alloc_file_pseudo+0xa5/0x100
    vfio_device_fops_unl_ioctl+0x26/0x30 [vfio]
    ? vfio_device_fops_unl_ioctl+0x26/0x30 [vfio]
    __x64_sys_ioctl+0x96/0xd0
    do_syscall_64+0x37/0x80
    entry_SYSCALL_64_after_hwframe+0x44/0xa9

Therefore, initialize prev_ga_tag to zero before use. This should be safe
because ga_tag value 0 is invalid (see function avic_vm_init).

Fixes: dfa20099e26e ("KVM: SVM: Refactor AVIC vcpu initialization into avic_init_vcpu()")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Message-Id: <20201003232707.4662-1-suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86/mmu: Commit zap of remaining invalid pages when recovering lpages

commit e89505698c9f70125651060547da4ff5046124fc upstream.

Call kvm_mmu_commit_zap_page() after exiting the "prepare zap" loop in
kvm_recover_nx_lpages() to finish zapping pages in the unlikely event
that the loop exited due to lpage_disallowed_mmu_pages being empty.
Because the recovery thread drops mmu_lock() when rescheduling, it's
possible that lpage_disallowed_mmu_pages could be emptied by a different
thread without to_zap reaching zero despite to_zap being derived from
the number of disallowed lpages.

Fixes: 1aa9b9572b105 ("kvm: x86: mmu: Recovery of shattered NX large pages")
Cc: Junaid Shahid <junaids@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: Return the error from crypt_message when enc/dec key not found.

commit 0bd294b55a5de442370c29fa53bab17aef3ff318 upstream.

In crypt_message, when smb2_get_enc_key returns error, we need to
return the error back to the caller. If not, we end up processing
the message further, causing a kernel oops due to unwarranted access
of memory.

Call Trace:
smb3_receive_transform+0x120/0x870 [cifs]
cifs_demultiplex_thread+0xb53/0xc20 [cifs]
? cifs_handle_standard+0x190/0x190 [cifs]
kthread+0x116/0x130
? kthread_park+0x80/0x80
ret_from_fork+0x1f/0x30

Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: remove bogus debug code

commit d367cb960ce88914898cbfa43645c2e43ede9465 upstream.

The "end" pointer is either NULL or it points to the next byte to parse.
If there isn't a next byte then dereferencing "end" is an off-by-one out
of bounds error.  And, of course, if it's NULL that leads to an Oops.
Printing "*end" doesn't seem very useful so let's delete this code.

Also for the last debug statement, I noticed that it should be printing
"sequence_end" instead of "end" so fix that as well.

Reported-by: Dominik Maier <dmaier@sect.tu-berlin.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

icmp: randomize the global rate limiter

[ Upstream commit b38e7819cae946e2edf869e604af1e65a5d241c5 ]

Keyu Man reported that the ICMP rate limiter could be used
by attackers to get useful signal. Details will be provided
in an upcoming academic publication.

Our solution is to add some noise, so that the attackers
no longer can get help from the predictable token bucket limiter.

Fixes: 4cdf507d5452 ("icmp: add a global rate limitation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: fix to update snd_wl1 in bulk receiver fast path

[ Upstream commit 18ded910b589839e38a51623a179837ab4cc3789 ]

In the header prediction fast path for a bulk data receiver, if no
data is newly acknowledged then we do not call tcp_ack() and do not
call tcp_ack_update_window(). This means that a bulk receiver that
receives large amounts of data can have the incoming sequence numbers
wrap, so that the check in tcp_may_update_window fails:
   after(ack_seq, tp->snd_wl1)

If the incoming receive windows are zero in this state, and then the
connection that was a bulk data receiver later wants to send data,
that connection can find itself persistently rejecting the window
updates in incoming ACKs. This means the connection can persistently
fail to discover that the receive window has opened, which in turn
means that the connection is unable to send anything, and the
connection's sending process can get permanently "stuck".

The fix is to update snd_wl1 in the header prediction fast path for a
bulk data receiver, so that it keeps up and does not see wrapping
problems.

This fix is based on a very nice and thorough analysis and diagnosis
by Apollon Oikonomopoulos (see link below).

This is a stable candidate but there is no Fixes tag here since the
bug predates current git history. Just for fun: looks like the bug
dates back to when header prediction was added in Linux v2.1.8 in Nov
1996. In that version tcp_rcv_established() was added, and the code
only updates snd_wl1 in tcp_ack(), and in the new "Bulk data transfer:
receiver" code path it does not call tcp_ack(). This fix seems to
apply cleanly at least as far back as v3.2.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reported-by: Apollon Oikonomopoulos <apoikos@dmesg.gr>
Tested-by: Apollon Oikonomopoulos <apoikos@dmesg.gr>
Link: https://www.spinics.net/lists/netdev/msg692430.html
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201022143331.1887495-1-ncardwell.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfc: Ensure presence of NFC_ATTR_FIRMWARE_NAME attribute in nfc_genl_fw_download()

[ Upstream commit 280e3ebdafb863b3cb50d5842f056267e15bf40c ]

Check that the NFC_ATTR_FIRMWARE_NAME attributes are provided by
the netlink client prior to accessing them.This prevents potential
unhandled NULL pointer dereference exceptions which can be triggered
by malicious user-mode programs, if they omit one or both of these
attributes.

Similar to commit a0323b979f81 ("nfc: Ensure presence of required attributes in the activate_target handler").

Fixes: 9674da8759df ("NFC: Add firmware upload netlink command")
Signed-off-by: Defang Bo <bodefang@126.com>
Link: https://lore.kernel.org/r/1603107538-4744-1-git-send-email-bodefang@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hdlc_raw_eth: Clear the IFF_TX_SKB_SHARING flag after calling ether_setup

[ Upstream commit 5fce1e43e2d5bf2f7e3224d7b99b1c65ab2c26e2 ]

This driver calls ether_setup to set up the network device.
The ether_setup function would add the IFF_TX_SKB_SHARING flag to the
device. This flag indicates that it is safe to transmit shared skbs to
the device.

However, this is not true. This driver may pad the frame (in eth_tx)
before transmission, so the skb may be modified.

Fixes: 550fd08c2ceb ("net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared")
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020063420.187497-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hdlc: In hdlc_rcv, check to make sure dev is an HDLC device

[ Upstream commit 01c4ceae0a38a0bdbfea6896f41efcd985a9c064 ]

The hdlc_rcv function is used as hdlc_packet_type.func to process any
skb received in the kernel with skb->protocol == htons(ETH_P_HDLC).
The purpose of this function is to provide second-stage processing for
skbs not assigned a "real" L3 skb->protocol value in the first stage.

This function assumes the device from which the skb is received is an
HDLC device (a device created by this module). It assumes that
netdev_priv(dev) returns a pointer to "struct hdlc_device".

However, it is possible that some driver in the kernel (not necessarily
in our control) submits a received skb with skb->protocol ==
htons(ETH_P_HDLC), from a non-HDLC device. In this case, the skb would
still be received by hdlc_rcv. This will cause problems.

hdlc_rcv should be able to recognize and drop invalid skbs. It should
first make sure "dev" is actually an HDLC device, before starting its
processing. This patch adds this check to hdlc_rcv.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020013152.89259-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: bebob: potential info leak in hwdep_read()

commit b41c15f4e1c1f1657da15c482fa837c1b7384452 upstream.

The "count" variable needs to be capped on every path so that we don't
copy too much information to the user.

Fixes: 618eabeae711 ("ALSA: bebob: Add hwdep interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201007074928.GA2529578@mwanda
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix UAF when releasing todo list

commit f3277cbfba763cd2826396521b9296de67cf1bbc upstream.

When releasing a thread todo list when tearing down
a binder_proc, the following race was possible which
could result in a use-after-free:

1.  Thread 1: enter binder_release_work from binder_thread_release
2.  Thread 2: binder_update_ref_for_handle() -> binder_dec_node_ilocked()
3.  Thread 2: dec nodeA --> 0 (will free node)
4.  Thread 1: ACQ inner_proc_lock
5.  Thread 2: block on inner_proc_lock
6.  Thread 1: dequeue work (BINDER_WORK_NODE, part of nodeA)
7.  Thread 1: REL inner_proc_lock
8.  Thread 2: ACQ inner_proc_lock
9.  Thread 2: todo list cleanup, but work was already dequeued
10. Thread 2: free node
11. Thread 2: REL inner_proc_lock
12. Thread 1: deref w->type (UAF)

The problem was that for a BINDER_WORK_NODE, the binder_work element
must not be accessed after releasing the inner_proc_lock while
processing the todo list elements since another thread might be
handling a deref on the node containing the binder_work element
leading to the node being freed.

Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20201009232455.4054810-1-tkjos@google.com
Cc: <stable@vger.kernel.org> # 4.14, 4.19, 5.4, 5.8
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

r8169: fix data corruption issue on RTL8402

[ Upstream commit ef9da46ddef071e1bbb943afbbe9b38771855554 ]

Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.

Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/ipv4: always honour route mtu during forwarding

[ Upstream commit 02a1b175b0e92d9e0fa5df3957ade8d733ceb6a0 ]

Documentation/networking/ip-sysctl.txt:46 says:
  ip_forward_use_pmtu - BOOLEAN
    By default we don't trust protocol path MTUs while forwarding
    because they could be easily forged and can lead to unwanted
    fragmentation by the router.
    You only need to enable this if you have user-space software
    which tries to discover path mtus by itself and depends on the
    kernel honoring this information. This is normally not the case.
    Default: 0 (disabled)
    Possible values:
    0 - disabled
    1 - enabled

Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).

Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...

It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.

Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).

This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.

I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.

Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: fix the skb_unshare() in tipc_buf_append()

[ Upstream commit ed42989eab57d619667d7e87dfbd8fe207db54fe ]

skb_unshare() drops a reference count on the old skb unconditionally,
so in the failure case, we end up freeing the skb twice here.
And because the skb is allocated in fclone and cloned by caller
tipc_msg_reassemble(), the consequence is actually freeing the
original skb too, thus triggered the UAF by syzbot.

Fix this by replacing this skb_unshare() with skb_cloned()+skb_copy().

Fixes: ff48b6222e65 ("tipc: use skb_unshare() instead in tipc_buf_append()")
Reported-and-tested-by: syzbot+e96a7ba46281824cc46a@syzkaller.appspotmail.com
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: usb: qmi_wwan: add Cellient MPL200 card

[ Upstream commit 28802e7c0c9954218d1830f7507edc9d49b03a00 ]

Add usb ids of the Cellient MPL200 card.

Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mlx4: handle non-napi callers to napi_poll

[ Upstream commit b2b8a92733b288128feb57ffa694758cf475106c ]

netcons calls napi_poll with a budget of 0 to transmit packets.
Handle this by:
 - skipping RX processing
 - do not try to recycle TX packets to the RX cache

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: Restore flowi4_oif update before call to xfrm_lookup_route

[ Upstream commit 874fb9e2ca949b443cc419a4f2227cafd4381d39 ]

Tobias reported regressions in IPsec tests following the patch
referenced by the Fixes tag below. The root cause is dropping the
reset of the flowi4_oif after the fib_lookup. Apparently it is
needed for xfrm cases, so restore the oif update to ip_route_output_flow
right before the call to xfrm_lookup_route.

Fixes: 2fbc6e89b2f1 ("ipv4: Update exception handling for multipath routes via same device")
Reported-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmveth: Identify ingress large send packets.

[ Upstream commit 413f142cc05cb03f2d1ea83388e40c1ddc0d74e9 ]

Ingress large send packets are identified by either:
The IBMVETH_RXQ_LRG_PKT flag in the receive buffer
or with a -1 placed in the ip header checksum.
The method used depends on firmware version. Frame
geometry and sufficient header validation is performed by the
hypervisor eliminating the need for further header checks here.

Fixes: 7b5967389f5a ("ibmveth: set correct gso_size and gso_type")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Reviewed-by: Cristobal Forno <cris.forno@ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmveth: Switch order of ibmveth_helper calls.

[ Upstream commit 5ce9ad815a296374ca21f43f3b1ab5083d202ee1 ]

ibmveth_rx_csum_helper() must be called after ibmveth_rx_mss_helper()
as ibmveth_rx_csum_helper() may alter ip and tcp checksum values.

Fixes: 66aa0678efc2 ("ibmveth: Support to enable LSO/CSO for Trunk VEA.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Reviewed-by: Cristobal Forno <cris.forno@ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.202

Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Link: https://lore.kernel.org/r/20201016090437.265805669@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: qat - check cipher length for aead AES-CBC-HMAC-SHA

commit 45cb6653b0c355fc1445a8069ba78a4ce8720511 upstream.

Return -EINVAL for authenc(hmac(sha1),cbc(aes)),
authenc(hmac(sha256),cbc(aes)) and authenc(hmac(sha512),cbc(aes))
if the cipher length is not multiple of the AES block.
This is to prevent an undefined device behaviour.

Fixes: d370cec32194 ("crypto: qat - Intel(R) QAT crypto interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dominik Przychodni <dominik.przychodni@intel.com>
[giovanni.cabiddu@intel.com: reworded commit message]
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: bcm - Verify GCM/CCM key length in setkey

commit 10a2f0b311094ffd45463a529a410a51ca025f27 upstream.

The setkey function for GCM/CCM algorithms didn't verify the key
length before copying the key and subtracting the salt length.

This patch delays the copying of the key til after the verification
has been done.  It also adds checks on the key length to ensure
that it's at least as long as the salt.

Fixes: 9d12ba86f818 ("crypto: brcm - Add Broadcom SPU driver")
Cc: <stable@vger.kernel.org>
Reported-by: kiyin(尹亮) <kiyin@tencent.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/net/ethernet/marvell/mvmdio.c: Fix non OF case

commit d934423ac26ed373dfe089734d505dca5ff679b6 upstream.

Orion5.x systems are still using machine files and not device-tree.
Commit 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be
specified for orion-mdio") has replaced devm_clk_get() with of_clk_get(),
leading to a oops at boot and not working network, as reported in
https://lists.debian.org/debian-arm/2019/07/msg00088.html and possibly in
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908712.

Link: https://lists.debian.org/debian-arm/2019/07/msg00088.html
Fixes: 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio")
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

reiserfs: Fix oops during mount

commit c2bb80b8bdd04dfe32364b78b61b6a47f717af52 upstream.

With suitably crafted reiserfs image and mount command reiserfs will
crash when trying to verify that XATTR_ROOT directory can be looked up
in / as that recurses back to xattr code like:

 xattr_lookup+0x24/0x280 fs/reiserfs/xattr.c:395
 reiserfs_xattr_get+0x89/0x540 fs/reiserfs/xattr.c:677
 reiserfs_get_acl+0x63/0x690 fs/reiserfs/xattr_acl.c:209
 get_acl+0x152/0x2e0 fs/posix_acl.c:141
 check_acl fs/namei.c:277 [inline]
 acl_permission_check fs/namei.c:309 [inline]
 generic_permission+0x2ba/0x550 fs/namei.c:353
 do_inode_permission fs/namei.c:398 [inline]
 inode_permission+0x234/0x4a0 fs/namei.c:463
 lookup_one_len+0xa6/0x200 fs/namei.c:2557
 reiserfs_lookup_privroot+0x85/0x1e0 fs/reiserfs/xattr.c:972
 reiserfs_fill_super+0x2b51/0x3240 fs/reiserfs/super.c:2176
 mount_bdev+0x24f/0x360 fs/super.c:1417

Fix the problem by bailing from reiserfs_xattr_get() when xattrs are not
yet initialized.

CC: stable@vger.kernel.org
Reported-by: syzbot+9b33c9b118d77ff59b6f@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

reiserfs: Initialize inode keys properly

commit 4443390e08d34d5771ab444f601cf71b3c9634a4 upstream.

reiserfs_read_locked_inode() didn't initialize key length properly. Use
_make_cpu_key() macro for key initialization so that all key member are
properly initialized.

CC: stable@vger.kernel.org
Reported-by: syzbot+d94d02749498bb7bab4b@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ftdi_sio: add support for FreeCalypso JTAG+UART adapters

commit 6cf87e5edd9944e1d3b6efd966ea401effc304ee upstream.

There exist many FT2232-based JTAG+UART adapter designs in which
FT2232 Channel A is used for JTAG and Channel B is used for UART.
The best way to handle them in Linux is to have the ftdi_sio driver
create a ttyUSB device only for Channel B and not for Channel A:
a ttyUSB device for Channel A would be bogus and will disappear as
soon as the user runs OpenOCD or other applications that access
Channel A for JTAG from userspace, causing undesirable noise for
users.  The ftdi_sio driver already has a dedicated quirk for such
JTAG+UART FT2232 adapters, and it requires assigning custom USB IDs
to such adapters and adding these IDs to the driver with the
ftdi_jtag_quirk applied.

Boutique hardware manufacturer Falconia Partners LLC has created a
couple of JTAG+UART adapter designs (one buffered, one unbuffered)
as part of FreeCalypso project, and this hardware is specifically made
to be used with Linux hosts, with the intent that Channel A will be
accessed only from userspace via appropriate applications, and that
Channel B will be supported by the ftdi_sio kernel driver, presenting
a standard ttyUSB device to userspace.  Toward this end the hardware
manufacturer will be programming FT2232 EEPROMs with custom USB IDs,
specifically with the intent that these IDs will be recognized by
the ftdi_sio driver with the ftdi_jtag_quirk applied.

Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[johan: insert in PID order and drop unused define]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: pl2303: add device-id for HP GC device

commit 031f9664f8f9356cee662335bc56c93d16e75665 upstream.

This is adds a device id for HP LD381 which is a pl2303GC-base device.

Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: check validity of wMaxPacketSize of usb endpoints found

commit e1f13c879a7c21bd207dc6242455e8e3a1e88b40 upstream.

While finding usb endpoints in vmk80xx_find_usb_endpoints(), check if
wMaxPacketSize = 0 for the endpoints found.

Some devices have isochronous endpoints that have wMaxPacketSize = 0
(as required by the USB-2 spec).
However, since this doesn't apply here, wMaxPacketSize = 0 can be
considered to be invalid.

Reported-by: syzbot+009f546aa1370056b1c2@syzkaller.appspotmail.com
Tested-by: syzbot+009f546aa1370056b1c2@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201010082933.5417-1-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: Add Telit FT980-KS composition

commit 924a9213358fb92fa3c3225d6d042aa058167405 upstream.

This commit adds the following Telit FT980-KS composition:

0x1054: rndis, diag, adb, nmea, modem, modem, aux

AT commands can be sent to /dev/ttyUSB2.

Signed-off-by: Leonid Bloch <lb.workbox@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/ce86bc05-f4e2-b199-0cdc-792715e3f275@asocscloud.com
Link: https://lore.kernel.org/r/20201004155813.2342-1-lb.workbox@gmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Cellient MPL200 card

commit 3e765cab8abe7f84cb80d4a7a973fc97d5742647 upstream.

Add usb ids of the Cellient MPL200 card.

Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/3db5418fe9e516f4b290736c5a199c9796025e3c.1601715478.git.wilken.gottwalt@mailbox.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: usbtv: Fix refcounting mixup

commit bf65f8aabdb37bc1a785884374e919477fe13e10 upstream.

The premature free in the error path is blocked by V4L
refcounting, not USB refcounting. Thanks to
Ben Hutchings for review.

[v2] corrected attributions

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 50e704453553 ("media: usbtv: prevent double free in error case")
CC: stable@vger.kernel.org
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Disconnect if E0 is used for Level 4

commit 8746f135bb01872ff412d408ea1aa9ebd328c1f5 upstream.

E0 is not allowed with Level 4:

BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part C page 1319:

  '128-bit equivalent strength for link and encryption keys
   required using FIPS approved algorithms (E0 not allowed,
   SAFER+ not allowed, and P-192 not allowed; encryption key
   not shortened'

SC enabled:

> HCI Event: Read Remote Extended Features (0x23) plen 13
        Status: Success (0x00)
        Handle: 256
        Page: 1/2
        Features: 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 0x00
          Secure Simple Pairing (Host Support)
          LE Supported (Host)
          Secure Connections (Host Support)
> HCI Event: Encryption Change (0x08) plen 4
        Status: Success (0x00)
        Handle: 256
        Encryption: Enabled with AES-CCM (0x02)

SC disabled:

> HCI Event: Read Remote Extended Features (0x23) plen 13
        Status: Success (0x00)
        Handle: 256
        Page: 1/2
        Features: 0x03 0x00 0x00 0x00 0x00 0x00 0x00 0x00
          Secure Simple Pairing (Host Support)
          LE Supported (Host)
> HCI Event: Encryption Change (0x08) plen 4
        Status: Success (0x00)
        Handle: 256
        Encryption: Enabled with E0 (0x01)
[May 8 20:23] Bluetooth: hci0: Invalid security: expect AES but E0 was used
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 256
        Reason: Authentication Failure (0x05)

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Hans-Christian Noren Egtvedt <hegtvedt@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Fix update of connection state in `hci_encrypt_cfm`

commit 339ddaa626995bc6218972ca241471f3717cc5f4 upstream.

Starting with the upgrade to v5.8-rc3, I've noticed I wasn't able to
connect to my Bluetooth headset properly anymore. While connecting to
the device would eventually succeed, bluetoothd seemed to be confused
about the current connection state where the state was flapping hence
and forth. Bisecting this issue led to commit 3ca44c16b0dc (Bluetooth:
Consolidate encryption handling in hci_encrypt_cfm, 2020-05-19), which
refactored `hci_encrypt_cfm` to also handle updating the connection
state.

The commit in question changed the code to call `hci_connect_cfm` inside
`hci_encrypt_cfm` and to change the connection state. But with the
conversion, we now only update the connection state if a status was set
already. In fact, the reverse should be true: the status should be
updated if no status is yet set. So let's fix the isuse by reversing the
condition.

Fixes: 3ca44c16b0dc ("Bluetooth: Consolidate encryption handling in hci_encrypt_cfm")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>