Michal Kazior [Thu, 8 May 2014 07:10:02 +0000 (09:10 +0200)]
mac80211: disconnect iface if CSA unexpectedly fails
It doesn't make much sense to leave a crippled
interface running.
As a side effect this will unblock tx queues with
CSA reason immediately after failure instead of
until after userspace requests interface to stop.
This also gives userspace an opportunity to
indirectly see CSA failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[small code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Loic Poulain [Wed, 7 May 2014 09:38:11 +0000 (11:38 +0200)]
rfkill-gpio: Use gpio cansleep version
If gpio controller requires waiting for read and write
GPIO values, then we have to use the gpio cansleep api.
Fix the rfkill_gpio_set_power which calls only the
nonsleep version (causing kernel warning).
There is no problem to use the cansleep version here
because we are not in IRQ handler or similar context
(cf rfkill_set_block).
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:45:36 +0000 (15:45 +0200)]
mac80211: ignore cqm during csa
It is not guaranteed that multi-vif channel
switching is tightly synchronized. It makes sense
to ignore cqm (missing beacons, et al) while csa
is progressing and re-check it after it completes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:11:01 +0000 (15:11 +0200)]
cfg80211: export interface stopping function
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:11:00 +0000 (15:11 +0200)]
mac80211: split CSA finalize function
Improves readability and modularity.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:10:59 +0000 (15:10 +0200)]
mac80211: fix CSA tx queue stopping
It was possible for tx queues to be stuck stopped
if AP CSA finalization failed. In that case
neither stop_ap nor do_stop woke the queues up.
This means it was impossible to perform tx at all
until driver was reloaded or a successful CSA was
performed later.
It was possible to solve this in a simpler manner
however this is more robust and future proof
(having multi-vif CSA in mind).
New sdata->csa_block_tx is introduced to keep
track of which interfaces requested tx to be
blocked for CSA. This is required because mac80211
stops all tx queues for that purpose. This means
queues must be awoken only when last tx-blocking
CSA interface is finished.
It is still possible to have tx queues stopped
after CSA failure but as soon as offending
interfaces are stopped from userspace (stop_ap or
ifdown) tx queues are woken up properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 9 Apr 2014 19:31:13 +0000 (21:31 +0200)]
mac80211: mark local variable __maybe_unused
The 'local' variable in __ieee80211_vif_copy_chanctx_to_vlans()
is only used/needed when lockdep is compiled in, mark it as such
to avoid compile warnings in the other case.
While at it, fix some indentation where it's used.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arik Nemtsov [Thu, 1 May 2014 07:17:28 +0000 (10:17 +0300)]
mac80211: move TDLS code to another file
With new additions planned, this code is getting too big for cfg.c.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arik Nemtsov [Thu, 1 May 2014 07:17:27 +0000 (10:17 +0300)]
mac80211: set an external flag for TDLS stations
Expose a new tdls flag for the public ieee80211_sta struct.
This can be used in some rate control decisions.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 29 Apr 2014 15:55:26 +0000 (17:55 +0200)]
mac80211: remove BUG_ON usage
These BUG_ON statements should never trigger, but in the unlikely
event that somebody does manage don't stop everything but simply
exit the code path with an error.
Leave the one BUG_ON where changing it would result in a NULL
pointer dereference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 29 Apr 2014 15:52:36 +0000 (17:52 +0200)]
cfg80211: remove BUG_ON usage
These really can't trigger unless somebody messes up the code,
but don't make debugging it needlessly complicated, WARN and
return instead of BUG_ON().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Mon, 28 Apr 2014 08:22:46 +0000 (11:22 +0300)]
mac80211_hwsim: Advertise support for AP mode channel width changes
mac80211 takes care of all the needed steps for hwsim, so indicate
support for this capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Mon, 28 Apr 2014 08:22:25 +0000 (11:22 +0300)]
mac80211: Support dynamic AP mode channel width changes
Implement the new cfg80211 capability to enable mac80211-based drivers
to support for dynamic channel bandwidth changes (e.g., HT 20/40 MHz
changes).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Mon, 28 Apr 2014 08:22:08 +0000 (11:22 +0300)]
cfg80211: Dynamic channel bandwidth changes in AP mode
This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Sat, 26 Apr 2014 01:43:41 +0000 (09:43 +0800)]
mac80211: remove unnecessary assignment
P2P_DEVICE doesn't support ieee80211_bss_info_change_notify() for now,
so it's not needed to set changed flags for P2P_DEVICE.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Sat, 26 Apr 2014 01:43:40 +0000 (09:43 +0800)]
mac80211: avoid calling useless channel context code
ieee80211_assign_chanctx() checks if local->use_chanctx is true, so
the two code block related to ieee80211_assign_chanctx() can be moved
into above if clause, emphasize that these code are executed only if
local->use_chanctx is true.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
[change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rostislav Lisovy [Tue, 15 Apr 2014 12:37:56 +0000 (14:37 +0200)]
cfg80211: Use 5MHz bandwidth by default when checking usable channels
Current code checks if the 20MHz bandwidth is allowed for
particular channel -- if it is not, the channel is disabled.
Since we need to use 5/10 MHz channels, this code is modified in
the way that the default bandwidth to check is 5MHz. If the
maximum bandwidth allowed by the channel is smaller than 5MHz,
the channel is disabled. Otherwise the channel is used and the
flags are set according to the bandwidth allowed by the channel.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rostislav Lisovy [Tue, 15 Apr 2014 12:37:55 +0000 (14:37 +0200)]
cfg80211: Add attributes describing prohibited channel bandwidth
Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.
When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions. If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.
Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:05 +0000 (12:53 +0800)]
mac80211: change return value of notifier function
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:04 +0000 (12:53 +0800)]
cfg80211: change return value of notifier function
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:03 +0000 (12:53 +0800)]
cfg80211: change wiphy_to_dev function name
Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:02 +0000 (12:53 +0800)]
cfg80211: change registered device pointer name
Name "dev" is too common and ambiguous, let all the pointer name
pointing to struct cfg80211_registered_device be "rdev". This can
improve code readability and consistency(since other places have
already called it rdev).
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:00 +0000 (12:53 +0800)]
mac80211: remove unnecessary BUG_ON()
The BUG_ON(!err) can't be triggered in the code path, so remove
it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:52:59 +0000 (12:52 +0800)]
mac80211: return bool instead of numbers in yes/no function
And some code style changes in the function, and correct a typo in
comment.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marek Kwaczynski [Mon, 14 Apr 2014 09:27:21 +0000 (11:27 +0200)]
mac80211: add option to generate CCMP IVs only for mgmt frames
Some chips can encrypt managment frames in HW, but
require generated IV in the frame. Add a key flag
that allows us to achieve this.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[use BIT(0) to fill that spot, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:33 +0000 (15:29 +0200)]
mac80211: compute chanctx refcount on-the-fly
It doesn't make much sense to store refcount in
the chanctx structure. One still needs to hold
chanctx_mtx to get the value safely. Besides,
refcount isn't on performance critical paths.
This will make implementing chanctx reservation
refcounting a little easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:32 +0000 (15:29 +0200)]
mac80211: fix racy usage of chanctx->refcount
Channel context refcount is protected by
chanctx_mtx. Accessing the value without holding
the mutex is racy. RCU section didn't guarantee
anything here.
Theoretically ieee80211_channel_switch() could
fail to see refcount change and read "1" instead
of, e.g. "2". This means mac80211 could accept CSA
even though it shouldn't have.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:31 +0000 (15:29 +0200)]
mac80211: split ieee80211_free_chanctx()
The function did a little too much. Split it up so
the code can be easily reused in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:30 +0000 (15:29 +0200)]
mac80211: split ieee80211_new_chanctx()
The function did a little too much. Split it up so
the code can be easily reused in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:29 +0000 (15:29 +0200)]
mac80211: improve chanctx reservation lookup
Use a separate function to look for reservation
chanctx. For multi-interface/channel reservation
search sematics differ slightly.
The new routine allows reservations to be merged
with chanctx that are already reserved by other
interface(s).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:28 +0000 (15:29 +0200)]
mac80211: improve find_chanctx() for reservations
This allows new vifs to be assigned to a chanctx
as long as chanctx's reservation chandefs (if any)
and chanctx's current chandef (implied by assigned
vifs at the time, if any) and the new vif chandef
are all compatible.
This implies it is impossible to assign a new vif
to an in-place reservation chanctx.
This gives no advantages for single-channel
hardware. It makes sense for multi-channel
hardware only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:27 +0000 (15:29 +0200)]
mac80211: track reserved vifs in chanctx
This can be useful. Provides a more straghtforward
way to iterate over interfaces taking part in
chanctx reservation and allows tracking chanctx
usage explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:26 +0000 (15:29 +0200)]
mac80211: track assigned vifs in chanctx
This can be useful. Provides a more straghtforward
way to iterate over interfaces bound to a given
chanctx and allows tracking chanctx usage
explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:25 +0000 (15:29 +0200)]
mac80211: add support for radar detection for reservations
Initial chanctx reservation code wasn't aware of
radar detection requirements. This is necessary
for chanctx reservations to be used for channel
switching in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:24 +0000 (15:29 +0200)]
mac80211: prevent chanctx overcommit
Do not allocate more channel contexts than a
driver is capable for currently matching interface
combination.
This allows the ieee80211_vif_reserve_chanctx() to
act as a guard against breaking interface
combinations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:23 +0000 (15:29 +0200)]
mac80211: add max channel calculation utility function
The utility function has no uses yet. It is aimed
at future chanctx reservation management and
channel switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:22 +0000 (15:29 +0200)]
cfg80211: allow drivers to iterate over matching combinations
The patch splits cfg80211_check_combinations()
into an iterator function and a simple iteration
user.
This makes it possible for drivers to asses how
many channels can use given iftype setup. This in
turn can be used for future
multi-interface/multi-channel channel switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Wed, 23 Apr 2014 06:22:58 +0000 (09:22 +0300)]
cfg80211: Fix GO Concurrent relaxation on UNII-3
At some locations, channels 149-165 are considered a single
bundle, while at some other locations, e.g., Indonesia, channels
149-161 are considered a single bundle, while channel 165 belongs
to a different bundle. This means that:
1. A station interface connection to an AP on channel 165 allows
the instantiation of a P2P GO on channels 149-165.
2. A station interface connection to an AP on channels 149-161
does NOT allow the instantiation of a P2P GO on channel 165.
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bob Copeland [Tue, 15 Apr 2014 14:43:08 +0000 (10:43 -0400)]
mac80211: mesh: always use the latest target_sn
When a path target responds to a path request, its response
always contains the most up-to-date information; accordingly,
it should use the latest target_sn, regardless of
net_traversal_jiffies(). Otherwise, only the first path
response is considered when constructing a path, as it will
have the highest target_sn of all replies during that period.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bob Copeland [Tue, 15 Apr 2014 14:43:07 +0000 (10:43 -0400)]
mac80211: fix mesh_add_rsn_ie IE finding loop
Previously, the code to copy the RSN IE from the mesh config
would increment its pointer by one in the loop instead of by
the element length, so there was the potential for mistaking
another IE's data fields as the RSN IE.
cfg80211_find_ie() exists, so just use that.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bob Copeland [Tue, 15 Apr 2014 14:43:06 +0000 (10:43 -0400)]
mac80211: mesh: use u16 return type for u16 getter
u16_field_get() is a simple wrapper around get_unaligned_le16(),
and it is being assigned to a u16, so there's no need to
promote to u32 in the middle.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Tue, 15 Apr 2014 16:13:56 +0000 (19:13 +0300)]
mac80211: Allow HT capa override to add 40 MHz intolerant
This can be useful for testing purposes to confirm valid AP behavior on
HT 20/40 co-existence functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luis R. Rodriguez [Tue, 22 Apr 2014 03:39:35 +0000 (20:39 -0700)]
cfg80211: fix processing world regdomain when non modular
This allows processing of the last regulatory request when
we determine its still pending. Without this if a regulatory
request failed to get processed by userspace we wouldn't
be able to re-process it later. An example situation that can
lead to an unprocessed last_request is enabling cfg80211 to
be built-in to the kernel, not enabling CFG80211_INTERNAL_REGDB
and the CRDA binary not being available at the time the udev
rule that kicks of CRDA triggers.
In such a situation we want to let some cfg80211 triggers
eventually kick CRDA for us again. Without this if the first
cycle attempt to kick off CRDA failed we'd be stuck without
the ability to change process any further regulatory domains.
cfg80211 will trigger re-processing of the regulatory queue
whenever schedule_work(®_work) is called, currently this
happens when:
* suspend / resume
* disconnect
* a beacon hint gets triggered (non DFS 5 GHz AP found)
* a regulatory request gets added to the queue
We don't have any specific opportunistic late boot triggers
to address a late mount of where CRDA resides though, adding
that should be done separately through another patch.
Without an opportunistic fix then this fix relies at least
one of the triggeres above to happen.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arik Nemtsov [Tue, 22 Apr 2014 03:39:34 +0000 (20:39 -0700)]
cfg80211: avoid freeing last_request while in flight
Avoid freeing the last request while it is being processed. This can
happen in some cases if reg_work is kicked for some reason while the
currently pending request is in flight.
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Eliad Peller <eliad@wizery.com>
Tested-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Janusz Dziedzic [Wed, 9 Apr 2014 11:47:12 +0000 (13:47 +0200)]
cfg80211: reg: set DFS CAC time in case of custom regd
Set DFS CAC time also in case of using custom
and strict regulatory from drivers. In other case
we could have unset DFS CAC time directly after
driver loaded and before issue regulatory set from
user mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 9 Apr 2014 20:36:50 +0000 (22:36 +0200)]
cfg80211: ignore invalid BSSIDs when looking for BSSes
When looking for a BSS matching given parameters, ignore invalid
BSSIDs. This avoids, for example, trying to join an IBSS that has
a multicast BSSID, which isn't supported by all drivers nor is it
a valid configuration of the IBSS so better create a new one with
a correctly chosen random BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 9 Apr 2014 20:32:16 +0000 (22:32 +0200)]
cfg80211: reject invalid IBSS BSSIDs in wext compat code
Don't allow using a multicast address as the BSSID, that
isn't a valid configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Wed, 9 Apr 2014 01:28:06 +0000 (09:28 +0800)]
cfg80211: remove unused wiphy argument from cfg80211_wext_freq()
cfg80211_wext_freq() is declared in wext-compat.h, but its
parameter struct wiphy's declaration is not included there.
As the parameter isn't used, just remove it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
[remove parameter instead of changing to netdev]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Wed, 9 Apr 2014 01:28:09 +0000 (09:28 +0800)]
mac80211: fix some missing includes
Some header files in mac80211 don't include all the
header files they require, fix that.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rostislav Lisovy [Wed, 2 Apr 2014 13:31:55 +0000 (15:31 +0200)]
mac80211: Update conf_is_ht() to work properly with 5/10MHz channels
The channels with 5/10MHz bandwidth are not HT. We have to
reflect this in conf_is_ht() function which returns whether the
particular channel is HT or not.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kalle Valo [Thu, 3 Apr 2014 07:03:45 +0000 (10:03 +0300)]
cfg80211: update comment about WIPHY_FLAG_CUSTOM_REGULATORY
Commit
a2f73b6c5db3c ("cfg80211: move regulatory flags to their own variable")
renamed WIPHY_FLAG_CUSTOM_REGULATORY to REGULATORY_CUSTOM_REG, but missed to
update one comment.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pawel Kulakowski [Tue, 1 Apr 2014 05:13:21 +0000 (07:13 +0200)]
mac80211: Allow disabling LDPC
This allows user-space (wpa_supplicant) to disable LDPC coding.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Fri, 21 Mar 2014 13:52:15 +0000 (14:52 +0100)]
cfg80211: fix radar_detect combination checking
All bits from radar_detect must match combination
radar bitmask. Otherwise it is theoretically
possible to lead into an invalid combination
provided a driver reports strange combinations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Thu, 27 Feb 2014 12:33:47 +0000 (14:33 +0200)]
mac80211: allow reservation of a running chanctx
With single-channel drivers, we need to be able to change a running
chanctx if we want to use chanctx reservation. Not all drivers may be
able to do this, so add a flag that indicates support for it.
Changing a running chanctx can also be used as an optimization in
multi-channel drivers when the context needs to be reserved for future
usage.
Introduce IEEE80211_CHANCTX_RESERVED chanctx mode to mark a channel as
reserved so nobody else can use it (since we know it's going to
change). In the future, we may allow several vifs to use the same
reservation as long as they plan to use the chanctx on the same
future channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Wed, 30 Oct 2013 11:09:39 +0000 (13:09 +0200)]
mac80211: implement chanctx reservation
In order to support channel switch with multiple vifs and multiple
contexts, we implement a concept of channel context reservation. This
allows us to reserve a channel context to be used later.
The reservation functionality is not tied directly to channel switch
and may be used in other situations (eg. reserving a channel context
during IBSS join).
We first check if an existing compatible context exists and if it
does, we reserve it. If there is no compatible context we create a
new one and reserve it.
Additionally, split ieee80211_vif_copy_chanctx_to_vlans() so we can
call it while already holding the chanctx mutex.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Tue, 11 Mar 2014 16:24:12 +0000 (18:24 +0200)]
mac80211: refactor ieee80211_assign/unassign_vif_chanctx into one
Combine the functions into one, so that we can switch from one context
to the other without having to unassign and assign separately. This
is needed by the channel reservation functionality because otherwise
we have a small period of time when the chanctx is set to NULL, which
can cause problems if someone else is trying to dereference it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Thu, 30 Jan 2014 20:08:16 +0000 (22:08 +0200)]
mac80211: split ieee80211_vif_change_channel in two
ieee80211_vif_change_channel() locks chanctx_mtx. When implementing
channel reservation for CS, we will need to call the function to
change channel when the lock is already held, so split the part that
requires the lock out and leave the locking in the original function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 5 Mar 2014 12:14:08 +0000 (13:14 +0100)]
mac80211: protect AP VLAN list with local->mtx
It was impossible to change chanctx of master AP
for AP VLANs because the copy function requires
RTNL which can't be simply taken in mac80211 code
due to possible deadlocks.
This is required for future chanctx reservation
that re-bind vifs to new chanctx. This requires
safe AP VLAN iteration without RTNL.
Now VLANs can be iterated while holding either
RTNL or local->mtx because the list is modified
while holding both of these locks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Thu, 27 Feb 2014 09:07:21 +0000 (11:07 +0200)]
cfg80211/mac80211: move more combination checks to mac80211
Get rid of the cfg80211_can_add_interface() and
cfg80211_can_change_interface() functions by moving that functionality
to mac80211. With this patch all interface combination checks are now
out of cfg80211 (except for the channel switch case which will be
addressed in a future commit).
Additionally, modify the ieee80211_check_combinations() function so
that an undefined chandef can be passed, in order to use it before a
channel is defined.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Tue, 18 Feb 2014 15:07:53 +0000 (17:07 +0200)]
cfg80211/mac80211: move combination check to mac80211 for ibss
Now that mac80211 can check the interface combinations itself, move
the combinations check from cfg80211 to mac80211 when joining an IBSS.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Thu, 13 Feb 2014 09:31:59 +0000 (11:31 +0200)]
cfg80211/mac80211: move interface counting for combination check to mac80211
Move the counting part of the interface combination check from
cfg80211 to mac80211.
This is needed to simplify locking when the driver has to perform a
combination check by itself (eg. with channel-switch).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Tue, 18 Feb 2014 09:40:36 +0000 (11:40 +0200)]
cfg80211/mac80211: refactor cfg80211_chandef_dfs_required()
Some interface types don't require DFS (such as STATION, P2P_CLIENT
etc). In order to centralize these decisions, make
cfg80211_chandef_dfs_required() take the iftype into consideration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Mon, 17 Feb 2014 14:52:35 +0000 (16:52 +0200)]
cfg80211: refactor cfg80211_can_use_iftype_chan()
Separate the code that counts the interface types and channels from
the code that check the interface combinations. The new function that
checks for combinations is exported so it can be called by the
drivers.
This is done in preparation for moving the interface combinations
checks out of cfg80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Sun, 23 Feb 2014 07:13:03 +0000 (09:13 +0200)]
cfg80211: Enable GO operation on indoor channels
Allow GO operation on a channel marked with IEEE80211_CHAN_INDOOR_ONLY
iff there is a user hint indicating that the platform is operating in
an indoor environment, i.e., the platform is a printer or media center
device.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Tue, 25 Feb 2014 14:26:00 +0000 (16:26 +0200)]
cfg80211: Add an option to hint indoor operation
Add the option to hint the wireless core that it is operating in an indoor
environment.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Sun, 23 Feb 2014 07:13:01 +0000 (09:13 +0200)]
cfg80211: Enable GO operation on additional channels
Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT
iff there is an active station interface that is associated to
an AP operating on the same channel in the 2 GHz band or the same UNII band
(in the 5 GHz band). This relaxation is not allowed if the channel is
marked with IEEE80211_CHAN_RADAR.
Note that this is a permissive approach to the FCC definitions,
that require a clear assessment that the device operating the AP is
an authorized master, i.e., with radar detection and DFS capabilities.
It is assumed that such restrictions are enforced by user space.
Furthermore, it is assumed, that if the conditions that allowed for
the operation of the GO on such a channel change, i.e., the station
interface disconnected from the AP, it is the responsibility of user
space to evacuate the GO from the channel.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Sun, 23 Feb 2014 07:13:00 +0000 (09:13 +0200)]
cfg80211: Add Kconfig option for cellular BS hints
Move the regulatory cellular base station hints support under
a specific configuration option and make the option depend
on CFG80211_CERTIFICATION_ONUS.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David Spinadel [Sun, 23 Feb 2014 07:12:59 +0000 (09:12 +0200)]
cfg80211: Add indoor only and GO concurrent channel attributes
The FCC are clarifying some soft configuration requirements,
which among other include the following:
1. Indoor operation, where a device can use channels requiring indoor
operation, subject to that it can guarantee indoor operation,
i.e., the device is connected to AC Power or the device is under
the control of a local master that is acting as an AP and is
connected to AC Power.
2. Concurrent GO operation, where devices may instantiate a P2P GO
while they are under the guidance of an authorized master. For example,
on a channel on which a BSS is connected to an authorized master, i.e.,
with DFS and radar detection capability in the UNII band.
See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
Add support for advertising Indoor-only and GO-Concurrent channel
properties.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Wed, 19 Mar 2014 15:02:21 +0000 (23:02 +0800)]
cfg80211: slightly clean up of cfg80211_sme_connect()
Wdev->ssid_len has already been set in cfg80211_connect() and is equal
to connect->ssid_len. Use wdev->ssid_len instead of connect->ssid_len
so it will be consistent with previous ssid assignment statement.
If bss is found in cfg80211_get_conn_bss(), wdev->conn->state is set
to CFG80211_CONN_AUTHENTICATE_NEXT in there. So it's not needed to set
it manually to CFG80211_CONN_AUTHENTICATE_NEXT if bss is found in that
function.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Monam Agarwal [Sun, 23 Mar 2014 19:21:43 +0000 (00:51 +0530)]
mac80211: use RCU_INIT_POINTER
rcu_assign_pointer() ensures that the initialization of a structure is
carried out before storing a pointer to that structure. However, in the
case that NULL is assigned there's no structure to initialize so using
RCU_INIT_POINTER instead is safe and more efficient.
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
[squash eight tiny patches, rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Monam Agarwal [Sun, 23 Mar 2014 19:23:40 +0000 (00:53 +0530)]
cfg80211: regulatory: use RCU_INIT_POINTER
rcu_assign_pointer() ensures that the initialization of a structure is
carried out before storing a pointer to that structure. However, in the
case that NULL is assigned there's no structure to initialize so using
RCU_INIT_POINTER instead is safe and more efficient.
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Thu, 27 Mar 2014 09:30:29 +0000 (11:30 +0200)]
mac80211: add vif to flush call
This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 24 Mar 2014 16:57:27 +0000 (17:57 +0100)]
cfg80211: allow userspace to take ownership of interfaces
When dynamically creating interfaces from userspace, e.g. for P2P usage,
such interfaces are usually owned by the process that created them, i.e.
wpa_supplicant. Should wpa_supplicant crash, such interfaces will often
cease operating properly and cause problems on restarting the process.
To avoid this problem, introduce an ownership concept for interfaces. If
an interface is owned by a netlink socket, then it will be destroyed if
the netlink socket is closed for any reason, including if the process it
belongs to crashed. This gives us a race-free way to get rid of any such
interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jan-Simon Möller [Fri, 21 Mar 2014 06:39:32 +0000 (23:39 -0700)]
mac80211: remove VLAIS usage from mac80211
Replaced the use of a Variable Length Array In Struct (VLAIS) with a
C99 compliant equivalent. This is the original VLAIS struct.
struct {
struct aead_request req;
u8 priv[crypto_aead_reqsize(tfm)];
} aead_req;
This patch instead allocates the appropriate amount of memory using a
char array.
The new code can be compiled with both gcc and clang.
Signed-off-by: Jan-Simon Möller <dl9pf@gmx.de>
Signed-off-by: Behan Webster <behanw@converseincode.com>
[small style cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Thu, 3 Apr 2014 03:53:45 +0000 (20:53 -0700)]
Merge git://git./linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Linus Torvalds [Wed, 2 Apr 2014 23:24:28 +0000 (16:24 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- substantial cleanup of the generic and transport layers, in the
direction of an ultimate goal of making struct hid_device completely
transport independent, by Benjamin Tissoires
- cp2112 driver from David Barksdale
- a lot of fixes and new hardware support (Dualshock 4) to hid-sony
driver, by Frank Praznik
- support for Win 8.1 multitouch protocol by Andrew Duggan
- other smaller fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (75 commits)
HID: sony: fix force feedback mismerge
HID: sony: Set the quriks flag for Bluetooth controllers
HID: sony: Fix Sixaxis cable state detection
HID: uhid: Add UHID_CREATE2 + UHID_INPUT2
HID: hyperv: fix _raw_request() prototype
HID: hyperv: Implement a stub raw_request() entry point
HID: hid-sensor-hub: fix sleeping function called from invalid context
HID: multitouch: add support for Win 8.1 multitouch touchpads
HID: remove hid_output_raw_report transport implementations
HID: sony: do not rely on hid_output_raw_report
HID: cp2112: remove the last hid_output_raw_report() call
HID: cp2112: remove various hid_out_raw_report calls
HID: multitouch: add support of other generic collections in hid-mt
HID: multitouch: remove pen special handling
HID: multitouch: remove registered devices with default behavior
HID: hidp: Add a comment that some devices depend on the current behavior of uniq
HID: sony: Prevent duplicate controller connections.
HID: sony: Perform a boundry check on the sixaxis battery level index.
HID: sony: Fix work queue issues
HID: sony: Fix multi-line comment styling
...
Linus Torvalds [Wed, 2 Apr 2014 23:23:38 +0000 (16:23 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science -- mostly documentation and comment updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
sparse: fix comment
doc: fix double words
isdn: capi: fix "CAPI_VERSION" comment
doc: DocBook: Fix typos in xml and template file
Bluetooth: add module name for btwilink
driver core: unexport static function create_syslog_header
mmc: core: typo fix in printk specifier
ARM: spear: clean up editing mistake
net-sysfs: fix comment typo 'CONFIG_SYFS'
doc: Insert MODULE_ in module-signing macros
Documentation: update URL to hfsplus Technote 1150
gpio: update path to documentation
ixgbe: Fix format string in ixgbe_fcoe.
Kconfig: Remove useless "default N" lines
user_namespace.c: Remove duplicated word in comment
CREDITS: fix formatting
treewide: Fix typo in Documentation/DocBook
mm: Fix warning on make htmldocs caused by slab.c
ata: ata-samsung_cf: cleanup in header file
idr: remove unused prototype of idr_free()
Linus Torvalds [Wed, 2 Apr 2014 23:22:27 +0000 (16:22 -0700)]
Merge branch 'sched-idle-for-linus' of git://git./linux/kernel/git/tip/tip
Pull sched/idle changes from Ingo Molnar:
"More idle code reorganization, to prepare for more integration.
(Sent separately because it depended on pending timer work, which is
now upstream)"
* 'sched-idle-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/idle: Add more comments to the code
sched/idle: Move idle conditions in cpuidle_idle main function
sched/idle: Reorganize the idle loop
cpuidle/idle: Move the cpuidle_idle_call function to idle.c
idle/cpuidle: Split cpuidle_idle_call main function into smaller functions
Oleg Nesterov [Wed, 2 Apr 2014 15:45:05 +0000 (17:45 +0200)]
pid_namespace: pidns_get() should check task_active_pid_ns() != NULL
pidns_get()->get_pid_ns() can hit ns == NULL. This task_struct can't
go away, but task_active_pid_ns(task) is NULL if release_task(task)
was already called. Alternatively we could change get_pid_ns(ns) to
check ns != NULL, but it seems that other callers are fine.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Eric W. Biederman ebiederm@xmission.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 2 Apr 2014 21:50:10 +0000 (14:50 -0700)]
Merge tag 'kvm-3.15-1' of git://git./virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"PPC and ARM do not have much going on this time. Most of the cool
stuff, instead, is in s390 and (after a few releases) x86.
ARM has some caching fixes and PPC has transactional memory support in
guests. MIPS has some fixes, with more probably coming in 3.16 as
QEMU will soon get support for MIPS KVM.
For x86 there are optimizations for debug registers, which trigger on
some Windows games, and other important fixes for Windows guests. We
now expose to the guest Broadwell instruction set extensions and also
Intel MPX. There's also a fix/workaround for OS X guests, nested
virtualization features (preemption timer), and a couple kvmclock
refinements.
For s390, the main news is asynchronous page faults, together with
improvements to IRQs (floating irqs and adapter irqs) that speed up
virtio devices"
* tag 'kvm-3.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (96 commits)
KVM: PPC: Book3S HV: Save/restore host PMU registers that are new in POWER8
KVM: PPC: Book3S HV: Fix decrementer timeouts with non-zero TB offset
KVM: PPC: Book3S HV: Don't use kvm_memslots() in real mode
KVM: PPC: Book3S HV: Return ENODEV error rather than EIO
KVM: PPC: Book3S: Trim top 4 bits of physical address in RTAS code
KVM: PPC: Book3S HV: Add get/set_one_reg for new TM state
KVM: PPC: Book3S HV: Add transactional memory support
KVM: Specify byte order for KVM_EXIT_MMIO
KVM: vmx: fix MPX detection
KVM: PPC: Book3S HV: Fix KVM hang with CONFIG_KVM_XICS=n
KVM: PPC: Book3S: Introduce hypervisor call H_GET_TCE
KVM: PPC: Book3S HV: Fix incorrect userspace exit on ioeventfd write
KVM: s390: clear local interrupts at cpu initial reset
KVM: s390: Fix possible memory leak in SIGP functions
KVM: s390: fix calculation of idle_mask array size
KVM: s390: randomize sca address
KVM: ioapic: reinject pending interrupts on KVM_SET_IRQCHIP
KVM: Bump KVM_MAX_IRQ_ROUTES for s390
KVM: s390: irq routing for adapter interrupts.
KVM: s390: adapter interrupt sources
...
Linus Torvalds [Wed, 2 Apr 2014 21:43:17 +0000 (14:43 -0700)]
Merge tag 'virtio-next-for-linus' of git://git./linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing exciting: virtio-blk users might see a bit of a boost from the
doubling of the default queue length though"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-blk: base queue-depth on virtqueue ringsize or module param
Revert
a02bbb1ccfe8: MAINTAINERS: add virtio-dev ML for virtio
virtio: fail adding buffer on broken queues.
virtio-rng: don't crash if virtqueue is broken.
virtio_balloon: don't crash if virtqueue is broken.
virtio_blk: don't crash, report error if virtqueue is broken.
virtio_net: don't crash if virtqueue is broken.
virtio_balloon: don't softlockup on huge balloon changes.
virtio: Use pci_enable_msix_exact() instead of pci_enable_msix()
MAINTAINERS: virtio-dev is subscribers only
tools/virtio: add a missing )
tools/virtio: fix missing kmemleak_ignore symbol
tools/virtio: update internal copies of headers
Linus Torvalds [Wed, 2 Apr 2014 21:34:25 +0000 (14:34 -0700)]
Merge branch 'for-3.15' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping updates from Marek Szyprowski:
"This contains extension for more efficient handling of io address
space for dma-mapping subsystem for ARM architecture"
* 'for-3.15' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: dma-mapping: remove order parameter from arm_iommu_create_mapping()
arm: dma-mapping: Add support to extend DMA IOMMU mappings
Linus Torvalds [Wed, 2 Apr 2014 21:27:15 +0000 (14:27 -0700)]
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree changes from Grant Likely:
"Updates to devicetree core code. This branch contains the following
notable changes:
- add reserved memory binding
- make struct device_node a kobject and remove legacy
/proc/device-tree
- ePAPR conformance fixes
- update in-kernel DTC copy to version v1.4.0
- preparatory changes for dynamic device tree overlays
- minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of
the old /proc/device-tree code. This simplifies the device tree
handling code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (29 commits)
dt: Remove dangling "select PROC_DEVICETREE"
of: Add support for ePAPR "stdout-path" property
of: device_node kobject lifecycle fixes
of: only scan for reserved mem when fdt present
powerpc: add support for reserved memory defined by device tree
arm64: add support for reserved memory defined by device tree
of: add missing major vendors
of: add vendor prefix for SMSC
of: remove /proc/device-tree
of/selftest: Add self tests for manipulation of properties
of: Make device nodes kobjects so they show up in sysfs
arm: add support for reserved memory defined by device tree
drivers: of: add support for custom reserved memory drivers
drivers: of: add initialization code for dynamic reserved memory
drivers: of: add initialization code for static reserved memory
of: document bindings for reserved-memory nodes
Revert "of: fix of_update_property()"
kbuild: dtbs_install: new make target
ARM: mvebu: Allows to get the SoC ID even without PCI enabled
of: Allows to use the PCI translator without the PCI core
...
Linus Torvalds [Wed, 2 Apr 2014 21:10:21 +0000 (14:10 -0700)]
Merge tag 'pm+acpi-3.15-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are commits that were not quite ready when I sent the original
pull request for 3.15-rc1 several days ago, but they have spent some
time in linux-next since then and appear to be good to go. All of
them are fixes and cleanups.
Specifics:
- Remaining changes from upstream ACPICA release
20140214 that
introduce code to automatically serialize the execution of methods
creating any named objects which really cannot be executed in
parallel with each other anyway (previously ACPICA attempted to
address that by aborting methods upon conflict detection, but that
wasn't reliable enough and led to other issues). From Bob Moore
and Lv Zheng.
- intel_pstate fix to use del_timer_sync() instead of del_timer() in
the exit path before freeing the timer structure from Dirk
Brandewie (original patch from Thomas Gleixner).
- cpufreq fix related to system resume from Viresh Kumar.
- Serialization of frequency transitions in cpufreq that involve
PRECHANGE and POSTCHANGE notifications to avoid ordering issues
resulting from race conditions. From Srivatsa S Bhat and Viresh
Kumar.
- Revert of an ACPI processor driver change that was based on a
specific interpretation of the ACPI spec which may not be correct
(the relevant part of the spec appears to be incomplete). From
Hanjun Guo.
- Runtime PM core cleanups and documentation updates from Geert
Uytterhoeven.
- PNP core cleanup from Michael Opdenacker"
* tag 'pm+acpi-3.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Make cpufreq_notify_transition & cpufreq_notify_post_transition static
cpufreq: Convert existing drivers to use cpufreq_freq_transition_{begin|end}
cpufreq: Make sure frequency transitions are serialized
intel_pstate: Use del_timer_sync in intel_pstate_cpu_stop
cpufreq: resume drivers before enabling governors
PM / Runtime: Spelling s/competing/completing/
PM / Runtime: s/foo_process_requests/foo_process_next_request/
PM / Runtime: GENERIC_SUBSYS_PM_OPS is gone
PM / Runtime: Correct documented return values for generic PM callbacks
PM / Runtime: Split line longer than 80 characters
PM / Runtime: dev_pm_info.runtime_error is signed
Revert "ACPI / processor: Make it possible to get APIC ID via GIC"
ACPICA: Enable auto-serialization as a default kernel behavior.
ACPICA: Ignore sync_level for methods that have been auto-serialized.
ACPICA: Add additional named objects for the auto-serialize method scan.
ACPICA: Add auto-serialization support for ill-behaved control methods.
ACPICA: Remove global option to serialize all control methods.
PNP: remove deprecated IRQF_DISABLED
Linus Torvalds [Wed, 2 Apr 2014 20:47:29 +0000 (13:47 -0700)]
Merge branch 'powernv-cpuidle' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc non-virtualized cpuidle from Ben Herrenschmidt:
"This is the branch I mentioned in my other pull request which contains
our improved cpuidle support for the "powernv" platform
(non-virtualized).
It adds support for the "fast sleep" feature of the processor which
provides higher power savings than our usual "nap" mode but at the
cost of losing the timers while asleep, and thus exploits the new
timer broadcast framework to work around that limitation.
It's based on a tip timer tree that you seem to have already merged"
* 'powernv-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powernv: Parse device tree to setup idle states
cpuidle/powernv: Add "Fast-Sleep" CPU idle state
powerpc/powernv: Add OPAL call to resync timebase on wakeup
powerpc/powernv: Add context management for Fast Sleep
powerpc: Split timer_interrupt() into timer handling and interrupt handling routines
powerpc: Implement tick broadcast IPI as a fixed IPI message
powerpc: Free up the slot of PPC_MSG_CALL_FUNC_SINGLE IPI message
Linus Torvalds [Wed, 2 Apr 2014 20:42:59 +0000 (13:42 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/benh/powerpc
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
Linus Torvalds [Wed, 2 Apr 2014 20:40:50 +0000 (13:40 -0700)]
Merge branch 'mips-for-linux-next' of git://git.linux-mips.org/ralf/upstream-sfr
Pull MIPS updates from Ralf Baechle:
- Support for Imgtec's Aptiv family of MIPS cores.
- Improved detection of BCM47xx configurations.
- Fix hiberation for certain configurations.
- Add support for the Chinese Loongson 3 CPU, a MIPS64 R2 core and
systems.
- Detection and support for the MIPS P5600 core.
- A few more random fixes that didn't make 3.14.
- Support for the EVA Extended Virtual Addressing
- Switch Alchemy to the platform PATA driver
- Complete unification of Alchemy support
- Allow availability of I/O cache coherency to be runtime detected
- Improvments to multiprocessing support for Imgtec platforms
- A few microoptimizations
- Cleanups of FPU support
- Paul Gortmaker's fixes for the init stuff
- Support for seccomp
* 'mips-for-linux-next' of git://git.linux-mips.org/pub/scm/ralf/upstream-sfr: (165 commits)
MIPS: CPC: Use __raw_ memory access functions
MIPS: CM: use __raw_ memory access functions
MIPS: Fix warning when including smp-ops.h with CONFIG_SMP=n
MIPS: Malta: GIC IPIs may be used without MT
MIPS: smp-mt: Use common GIC IPI implementation
MIPS: smp-cmp: Remove incorrect core number probe
MIPS: Fix gigaton of warning building with microMIPS.
MIPS: Fix core number detection for MT cores
MIPS: MT: core_nvpes function to retrieve VPE count
MIPS: Provide empty mips_mt_set_cpuoptions when CONFIG_MIPS_MT=n
MIPS: Lasat: Replace del_timer by del_timer_sync
MIPS: Malta: Setup PM I/O region on boot
MIPS: Loongson: Add a Loongson-3 default config file
MIPS: Loongson 3: Add CPU hotplug support
MIPS: Loongson 3: Add Loongson-3 SMP support
MIPS: Loongson: Add Loongson-3 Kconfig options
MIPS: Loongson: Add swiotlb to support All-Memory DMA
MIPS: Loongson 3: Add serial port support
MIPS: Loongson 3: Add IRQ init and dispatch support
MIPS: Loongson 3: Add HT-linked PCI support
...
Josh Boyer [Wed, 2 Apr 2014 14:40:20 +0000 (10:40 -0400)]
arm64: Fix duplicated Kconfig entries again
Commit
74397174989e5f70 attempted to clean up the power management options
for arm64, but when things were merged it didn't fully take effect. Fix
it again.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 2 Apr 2014 20:15:58 +0000 (13:15 -0700)]
Merge branch 'x86-nuke-platforms-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 old platform removal from Peter Anvin:
"This patchset removes support for several completely obsolete
platforms, where the maintainers either have completely vanished or
acked the removal. For some of them it is questionable if there even
exists functional specimens of the hardware"
Geert Uytterhoeven apparently thought this was a April Fool's pull request ;)
* 'x86-nuke-platforms-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, platforms: Remove NUMAQ
x86, platforms: Remove SGI Visual Workstation
x86, apic: Remove support for IBM Summit/EXA chipset
x86, apic: Remove support for ia32-based Unisys ES7000
Linus Torvalds [Wed, 2 Apr 2014 19:51:41 +0000 (12:51 -0700)]
Merge branch 'x86-x32-for-linus' of git://git./linux/kernel/git/tip/tip
Pull compat time conversion changes from Peter Anvin:
"Despite the branch name this is really neither an x86 nor an
x32-specific patchset, although it the implementation of the
discussions that followed the x32 security hole a few months ago.
This removes get/put_compat_timespec/val() and replaces them with
compat_get/put_timespec/val() which are savvy as to the current status
of COMPAT_USE_64BIT_TIME.
It removes several unused and/or incorrect/misleading functions (like
compat_put_timeval_convert which doesn't in fact do any conversion)
and also replaces several open-coded implementations what is now
called compat_convert_timespec() with that function"
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Fix sparse address space warnings
compat: Get rid of (get|put)_compat_time(val|spec)
Linus Torvalds [Wed, 2 Apr 2014 19:26:43 +0000 (12:26 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 vdso changes from Peter Anvin:
"This is the revamp of the 32-bit vdso and the associated cleanups.
This adds timekeeping support to the 32-bit vdso that we already have
in the 64-bit vdso. Although 32-bit x86 is legacy, it is likely to
remain in the embedded space for a very long time to come.
This removes the traditional COMPAT_VDSO support; the configuration
variable is reused for simply removing the 32-bit vdso, which will
produce correct results but obviously suffer a performance penalty.
Only one beta version of glibc was affected, but that version was
unfortunately included in one OpenSUSE release.
This is not the end of the vdso cleanups. Stefani and Andy have
agreed to continue work for the next kernel cycle; in fact Andy has
already produced another set of cleanups that came too late for this
cycle.
An incidental, but arguably important, change is that this ensures
that unused space in the VVAR page is properly zeroed. It wasn't
before, and would contain whatever garbage was left in memory by BIOS
or the bootloader. Since the VVAR page is accessible to user space
this had the potential of information leaks"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86, vdso: Fix the symbol versions on the 32-bit vDSO
x86, vdso, build: Don't rebuild 32-bit vdsos on every make
x86, vdso: Actually discard the .discard sections
x86, vdso: Fix size of get_unmapped_area()
x86, vdso: Finish removing VDSO32_PRELINK
x86, vdso: Move more vdso definitions into vdso.h
x86: Load the 32-bit vdso in place, just like the 64-bit vdsos
x86, vdso32: handle 32 bit vDSO larger one page
x86, vdso32: Disable stack protector, adjust optimizations
x86, vdso: Zero-pad the VVAR page
x86, vdso: Add 32 bit VDSO time support for 64 bit kernel
x86, vdso: Add 32 bit VDSO time support for 32 bit kernel
x86, vdso: Patch alternatives in the 32-bit VDSO
x86, vdso: Introduce VVAR marco for vdso32
x86, vdso: Cleanup __vdso_gettimeofday()
x86, vdso: Replace VVAR(vsyscall_gtod_data) by gtod macro
x86, vdso: __vdso_clock_gettime() cleanup
x86, vdso: Revamp vclock_gettime.c
mm: Add new func _install_special_mapping() to mmap.c
x86, vdso: Make vsyscall_gtod_data handling x86 generic
...
Linus Torvalds [Wed, 2 Apr 2014 19:23:49 +0000 (12:23 -0700)]
Merge branch 'x86/boot' of git://git./linux/kernel/git/tip/tip
Pull x86 boot changes from Peter Anvin:
"This patchset is a set of cleanups aiming at librarize some of the
common code from the boot environments. We currently have three
different "little environments" (boot, boot/compressed, and
realmode/rm) in x86, and we are likely to soon get a fourth one
(kexec/purgatory, which will have to be integrated in the kernel to
support secure kexec). This is primarily a cleanup in the
anticipation of the latter.
While Vivek implemented this, he ran into some bugs, in particular the
memcmp implementation for when gcc punts from using the builtin would
have a misnamed symbol, causing compilation errors if we were ever
unlucky enough that gcc didn't want to inline the test"
* 'x86/boot' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Move memset() definition in compressed/string.c
x86, boot: Move memcmp() into string.h and string.c
x86, boot: Move optimized memcpy() 32/64 bit versions to compressed/string.c
x86, boot: Create a separate string.h file to provide standard string functions
x86, boot: Undef memcmp before providing a new definition
Linus Torvalds [Wed, 2 Apr 2014 19:22:03 +0000 (12:22 -0700)]
Merge tag 'metag-for-v3.15' of git://git./linux/kernel/git/jhogan/metag
Pull Metag architecture changes from James Hogan:
- Remove unused NUMA definition (SD_NODE_INIT)
- Refactor signal code to use struct ksignal
- IRQ migration cleanup to use irq_set_affinity
- Clean up main Kconfig file a little
* tag 'metag-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
sched: remove unused SCHED_INIT_NODE
metag: Use get_signal() signal_setup_done()
metag: Fix METAG Kconfig symbol select ordering
metag: Use irq_set_affinity instead of homebrewn code
Steven Rostedt (Red Hat) [Wed, 2 Apr 2014 17:26:41 +0000 (13:26 -0400)]
x86: Fix dumpstack_64 irq stack handling
Commit
2223f6f6eeaa "x86: Clean up dumpstack_64.c code" changed
the irq_stack processing a little from what it was before.
The irq_stack_end variable needed to be cleared after its first
use. By setting irq_stack to the per cpu irq_stack and passing
that to analyze_stack(), and then clearing it after it is processed,
we can get back the original behavior.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steven Rostedt (Red Hat) [Wed, 2 Apr 2014 17:26:40 +0000 (13:26 -0400)]
x86: Fix dumpstack_64 to keep state of "used" variable in loop
Commit
2223f6f6eeaa "x86: Clean up dumpstack_64.c code" moved the used
variable to a local within the loop, but the in_exception_stack()
depended on being non-volatile with the ability to change it.
By always re-initializing the "used" variable to zero, it would cause
the in_exception_stack() to return the same thing each time, and
cause the dump_stack loop to go into an infinite loop.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zhong [Mon, 31 Mar 2014 08:41:58 +0000 (16:41 +0800)]
sparse: fix comment
retmain -> remain
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Wed, 2 Apr 2014 02:43:53 +0000 (19:43 -0700)]
Merge branch 'for-3.15/drivers' of git://git.kernel.dk/linux-block
Pull block driver update from Jens Axboe:
"On top of the core pull request, here's the pull request for the
driver related changes for 3.15. It contains:
- Improvements for msi-x registration for block drivers (mtip32xx,
skd, cciss, nvme) from Alexander Gordeev.
- A round of cleanups and improvements for drbd from Andreas
Gruenbacher and Rashika Kheria.
- A round of clanups and improvements for bcache from Kent.
- Removal of sleep_on() and friends in DAC960, ataflop, swim3 from
Arnd Bergmann.
- Bug fix for a bug in the mtip32xx async completion code from Sam
Bradshaw.
- Bug fix for accidentally bouncing IO on 32-bit platforms with
mtip32xx from Felipe Franciosi"
* 'for-3.15/drivers' of git://git.kernel.dk/linux-block: (103 commits)
bcache: remove nested function usage
bcache: Kill bucket->gc_gen
bcache: Kill unused freelist
bcache: Rework btree cache reserve handling
bcache: Kill btree_io_wq
bcache: btree locking rework
bcache: Fix a race when freeing btree nodes
bcache: Add a real GC_MARK_RECLAIMABLE
bcache: Add bch_keylist_init_single()
bcache: Improve priority_stats
bcache: Better alloc tracepoints
bcache: Kill dead cgroup code
bcache: stop moving_gc marking buckets that can't be moved.
bcache: Fix moving_pred()
bcache: Fix moving_gc deadlocking with a foreground write
bcache: Fix discard granularity
bcache: Fix another bug recovering from unclean shutdown
bcache: Fix a bug recovering from unclean shutdown
bcache: Fix a journalling reclaim after recovery bug
bcache: Fix a null ptr deref in journal replay
...
Linus Torvalds [Wed, 2 Apr 2014 02:19:15 +0000 (19:19 -0700)]
Merge branch 'for-3.15/core' of git://git.kernel.dk/linux-block
Pull core block layer updates from Jens Axboe:
"This is the pull request for the core block IO bits for the 3.15
kernel. It's a smaller round this time, it contains:
- Various little blk-mq fixes and additions from Christoph and
myself.
- Cleanup of the IPI usage from the block layer, and associated
helper code. From Frederic Weisbecker and Jan Kara.
- Duplicate code cleanup in bio-integrity from Gu Zheng. This will
give you a merge conflict, but that should be easy to resolve.
- blk-mq notify spinlock fix for RT from Mike Galbraith.
- A blktrace partial accounting bug fix from Roman Pen.
- Missing REQ_SYNC detection fix for blk-mq from Shaohua Li"
* 'for-3.15/core' of git://git.kernel.dk/linux-block: (25 commits)
blk-mq: add REQ_SYNC early
rt,blk,mq: Make blk_mq_cpu_notify_lock a raw spinlock
blk-mq: support partial I/O completions
blk-mq: merge blk_mq_insert_request and blk_mq_run_request
blk-mq: remove blk_mq_alloc_rq
blk-mq: don't dump CPU -> hw queue map on driver load
blk-mq: fix wrong usage of hctx->state vs hctx->flags
blk-mq: allow blk_mq_init_commands() to return failure
block: remove old blk_iopoll_enabled variable
blktrace: fix accounting of partially completed requests
smp: Rename __smp_call_function_single() to smp_call_function_single_async()
smp: Remove wait argument from __smp_call_function_single()
watchdog: Simplify a little the IPI call
smp: Move __smp_call_function_single() below its safe version
smp: Consolidate the various smp_call_function_single() declensions
smp: Teach __smp_call_function_single() to check for offline cpus
smp: Remove unused list_head from csd
smp: Iterate functions through llist_for_each_entry_safe()
block: Stop abusing rq->csd.list in blk-softirq
block: Remove useless IPI struct initialization
...
Linus Torvalds [Wed, 2 Apr 2014 01:49:04 +0000 (18:49 -0700)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch consists of the usual driver updates (megaraid_sas,
scsi_debug, qla2xxx, qla4xxx, lpfc, bnx2fc, be2iscsi, hpsa, ipr) plus
an assortment of minor fixes and the first precursors of SCSI-MQ (the
code path simplifications) and the bug fix for the USB oops on remove
(which involves an infrastructure change, so is sent via the main tree
with a delayed backport after a cycle in which it is shown to
introduce no new bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (196 commits)
[SCSI] sd: Quiesce mode sense error messages
[SCSI] add support for per-host cmd pools
[SCSI] simplify command allocation and freeing a bit
[SCSI] megaraid: simplify internal command handling
[SCSI] ses: Use vpd information from scsi_device
[SCSI] Add EVPD page 0x83 and 0x80 to sysfs
[SCSI] Return VPD page length in scsi_vpd_inquiry()
[SCSI] scsi_sysfs: Implement 'is_visible' callback
[SCSI] hpsa: update driver version to 3.4.4-1
[SCSI] hpsa: fix bad endif placement in RAID 5 mapper code
[SCSI] qla2xxx: Fix build errors related to invalid print fields on some architectures.
[SCSI] bfa: Replace large udelay() with mdelay()
[SCSI] vmw_pvscsi: Some improvements in pvscsi driver.
[SCSI] vmw_pvscsi: Add support for I/O requests coalescing.
[SCSI] vmw_pvscsi: Fix pvscsi_abort() function.
[SCSI] remove deprecated IRQF_DISABLED from SCSI
[SCSI] bfa: Updating Maintainers email ids
[SCSI] ipr: Add new CCIN definition for Grand Canyon support
[SCSI] ipr: Format HCAM overlay ID 0x21
[SCSI] ipr: Use pci_enable_msi_range() and pci_enable_msix_range()
...
Linus Torvalds [Wed, 2 Apr 2014 00:06:09 +0000 (17:06 -0700)]
Merge tag 'usb-3.15-rc1' of git://git./linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...