[PATCH] git-netdev-all-ieee80211_get_payload-warning-fix

include/net/ieee80211.h: In function `ieee80211_get_payload':
include/net/ieee80211.h:1046: warning: control reaches end of non-void function

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] drivers/net/wireless/hermes.c unsigned int comparision

hermas_bap_pread,  hermes_bap_pwrite, and hermes_bap_pwrite_pad all have a parameter "len" that is declared unsigned,
but checked for a value less than zero. Auditing the callers, it is possible for len to be passed a negative value, so len should be an int.

Thanks to LinuxICC (http://linuxicc.sf.net)

Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] prism54 : Remove extraneous udelay/register read

In isl_38xx.c
In routine isl38xx_trigger-device

Move unnecessary udelay/register read.
This is only required when hand-compiling the driver and
setting  VERBOSE > SHOW_ERROR_MESSAGES

Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] SAA9730: Add missing header bits.

This header file patch was missing from the recent SAA9730 patch.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] au1000_eth: Include <linux/config.h>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Au1000 ethernet driver references plenty of CONFIG_* symbols.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] IOC3: Replace obsolete PCI API

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] i82593.h: make header comment GPL-compatible

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] e100: re-enable microcode with more useful defaults

For the four versions of hardware that we (currently) support microcode
download on, the default configuration of our receive interrupt mitigation
microcode was too aggressive, and caused unnecessary delays when pinging,
and low(er) throughput on single connection latency sensitive performance
tests.

This code adds microcode support, and sets the defaults to more reasonable
settings. It also explains the functionality in the code in more detail.
Compile and load tested, shows expected behavior for slight delay of ping
packets (1-2ms) when ucode is loaded, and decent interrupt moderation for
small packets, while maintaining good throughput.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Merge branch 'halasa-hdlc' of git://git.tuxdriver.com/git/netdev-jwl

Merge branch 'for-jeff' of git://electric-eye.fr.zoreil.com/home/romieu/linux-2.6

[PATCH] smc91x: fix bank mismatch

The smc91x driver relies upon register bank 2 being selected whenever
the interrupt handler is called.  This isn't always so, especially if
we have a link change event during PHY configuration.

This results in register bank 0 being selected when the interrupt
handler is called, causing the wrong registers to be read for the
IRQ mask and status.  In turn, this causes us to spin with a
permanently asserted IRQ.

The patch ensures that smc_phy_configure always exits with register
bank 2 selected.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] smc91x: fix one source of spurious interrupts

Not only SMC_ACK_INT(IM_TX_EMPTY_INT) in in smc_hardware_send_pkt)
appears to be unnecessary (tested with an SMC91C94 and SMC91C111), but
it seems to trigger spurious interrupts on some machines as well.
Removed.

While at it, let's log any remaining spurious interrupts if any (and
clean usage of the max IRQ loop count value).

Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

[PATCH] s390: fix class_device_create calls in 3270 the driver

Add the missing NULL argument to the class_device_create calls.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc64 need HPAGE_SHIFT when huge pages disabled

With the new powerpc architecture we don't seem to be able to disable huge
pages anymore.

    mm/built-in.o(.toc1+0xae0): undefined reference to `HPAGE_SHIFT'
    make: *** [.tmp_vmlinux1] Error 1

We seem to need to define HPAGE_SHIFT to something when HUGETLB_PAGE isn't
defined.  This patch defines it to PAGE_SHIFT when we have no support.

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] md: fix is_mddev_idle calculation now that disk/sector accounting happens when request completes

md needs to monitor the rate of requests to its devices when doing
resync/recovery so that it can back-off when there is non-resync IO.  It
does this by comparing resync IO, which it counts, with total IO which is
taken from disk_stats.

disk_stats were recently changed to account sectors when a request
completes instead of when it is queued.  This upsets md's calculations.

We could do the sync_io accounting at the end of requests too, but that has
problems.  If an underlying device is an md array, the accounting will
still be done when the request is submitted.  This could be changed for
some raid levels, but it cannot be changed for raid0 or linear without
substantial code changes.

So instead, we increase the error that is_mddev_idle allows, up to the
maximum amount of resync IO that can be in flight at any time.  The
calculation is current fragile as each personality as different limits for
in-flight resync.  This should be fixed up.

For now, this simple patch fixes the problem.

Increasing the error margin decreases the sensitivity to non-resync IO.  To
partially compensate for this, the time to wait when non-resync IO is
detected is increased so that less steady IO is required to keep the resync
at bay.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] md: don't pass a NULL file* into ->prepare_write()

Some filesystems go oops.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] tpm: remove PCI kconfig dependency

The driver dependencies on PCI have been removed.  This patch clears that
up in the Kconfig file

Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] tpm: use ioread8 and iowrite8

Use ioread8 and iowrite8 as suggested.

Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] tpm: use flush_scheduled_work()

Add the necessary flush_schedule_work calls when canceling the timer.

Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc32: add missing define for fs_enet Ethernet driver

This adds the FCC_PSMR_RMII defenition, which is used in fs_enet to enable
RMII mode.

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ipmi: missing NULL test for kthread

On IPMI systems with BT interfaces, we don't start the kernel thread, so
smi_info->thread is NULL.  Test for NULL when stopping the thread, because
kthread_stop() doesn't, and an oops ensues otherwise.

Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] re-export clear_page_dirty_for_io()

2.6.14 has this exported, and reiser4 (at least) uses it.  Put things back
the way they were.

Signed-off-by: Vladimir V. Saveliev <vs@namesys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] add success/failure indication to RCU torture test

One issue with the RCU torture test is that the current error flagging can
be lost in dmesg.  This patch adds a "SUCCESS"/"FAILURE" string to the line
that flags the end of the test, where it can easily be seen with "dmesg |
tail" at the end of the test.  Also adds tests of architecture-specific
memory barriers -- or, more likely, of the RCU torture test itself.

Cc: <vatsa@in.ibm.com>
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Fix copy-paste bug in ohci-ppc-soc.c

Fix copy-paste bug in ohci-ppc-soc.c(ohci_hcd_ppc_soc_drv_remove)

Signed-off-by: Andrey Volkov <avolkov@varma-el.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix ACPI processor power block initialization

Properly clear the memory, and set "pr->flags.power" only if a C2 or
deeper state is valid (to make the code match both the comment and
previous behaviour).

This fixes a boot-time lockup reported by Maneesh Soni when using
"maxcpus=1".

Acked-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge git://git./linux/kernel/git/paulus/powerpc-merge

offb: Fix compile error on ppc32 systems

The code Ben H added needs <linux/pci.h> for things like pci_dev, etc.

Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Move defconfig over and remove remaining arch/ppc64 files

make defconfig will now use arch/powerpc/configs/ppc64_defconfig
if running on a ppc64 system.  I need to add an
arch/powerpc/configs/ppc_defconfig sometime.

Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Fix a couple of compile warnings for 32-bit compiles

Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: time-of-day fixes for 32-bit CHRP systems

This makes 32-bit CHRP systems use the RTAS time-of-day routines if
available.  It fixes a bug in the RTAS time-of-day routines where they
were storing a 64-bit timebase value in an unsigned long by making
those variables u64.  Also, the direct-access time-of-day routines
had the wrong convention for the month and year in the struct rtc_time.

Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Fix compile error on pSeries arising from delay.h changes

pseries_dedicated_idle() was using __get_tb which used to be defined
in asm/delay.h.  Change it to use get_tb from asm/time.h, which is
in fact exactly the same thing.

Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Move remaining .c files from arch/ppc64 to arch/powerpc

This also deletes the now-unused Makefiles under arch/ppc64.

Both of the files moved over could use some merging, but for now I
have moved them as-is and arranged for them to be used only in 64-bit
kernels.  For 32-bit kernels we still use arch/ppc/kernel/idle.c and
drivers/char/generic_nvram.c as before.

Signed-off-by: Paul Mackerras <paulus@samba.org>

[PATCH] Remove SPAN_OTHER_NODES config definition

The config option SPAN_OTHER_NODES was created so that we could
make pSeries numa layouts work within the DISCONTIG memory model.
Now that DISCONTIG has been replaced by SPARSEMEM, we can eliminate
this option.

I'll be sending a separate patch to Andrew to remove the arch
independent code as pSeries was the only arch that needed this.

Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[PATCH] powerpc: merge align.c

This patch merges align.c, the result isn't quite what was in ppc64 nor
what was in ppc32 :) It should implement all the functionalities of both
though. Kumar, since you played with that in the past, I suppose you
have some test cases for verifying that it works properly before I dig
out the 601 machine ? :)

Since it's likely that I won't be able to test all scenario, code
inspection is much welcome.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Fix delay functions for 601 processors

My earlier merge of delay.h introduced a timebase-based udelay for
32-bit machines but also broke the 601, which doesn't have the
timebase register.  This fixes it by using the 601's RTC register on
the 601, and also moves __delay() and udelay() to be out-of-line in
arch/powerpc/kernel/time.c.  These functions aren't really performance
critical, after all.

Signed-off-by: Paul Mackerras <paulus@samba.org>

[PATCH] ppc: Fix warnings related to seq_file

When we moved things around in irq.h seq_file became an issue.  Fix
warnings related to its usage.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[PATCH] ppc: Fix MPC83xx device table

The SVRs for MPC8343/E were incorrect and really the SVRs
for MPC8347/E.

Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[PATCH] powerpc: Maple: request I/O resource.

Reserve the Maple RTC I/O resource.  Needed now we use genrtc.

Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[PATCH] ppc boot: replace string labels with numbers

Replacing the string labels with numbers saves 117 bytes in the final zImage.
These local labels are not discared.

Signed-off-by: Olaf Hering <olh@suse.de>
 arch/powerpc/boot/crt0.S |   23 +++++++++++------------
 1 files changed, 11 insertions(+), 12 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>

[PATCH] powerpc: Fix typo in topology.h

The fix to topology.h (5cfccd7f132432dd4705444a44b51d12ef88a85f) seems to have
a typeo, struct sched_domain has an idle_idx member but not an idle_id
member. I assume this is the fix.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Merge /pub/scm/linux/kernel/git/davem/sparc-2.6

Merge /pub/scm/linux/kernel/git/davem/net-2.6

[PATCH] ppc: Fix warnings related to seq_file

When we moved things around in irq.h seq_file became an issue.  Fix
warnings related to its usage.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[IPV6]: Fib dump really needs GFP_ATOMIC.

Revert: 8225ccbaf01b459cf1e462047a51b2851e756bc1

Based upon a report by Yan Zheng.

Signed-off-by: David S. Miller <davem@davemloft.net>

[NET]: Sanitize NET_SCHED protection in /net/sched/Kconfig

On Thu, 17 Nov 2005, David Gómez wrote:

> I found out that if i select NET_CLS_ROUTE4, save my changes and exit
> menuconfig, execute again make menuconfig and go to QoS options, then the new
> available options are visible. So menuconfig has some problem refreshing
> contents :?

No, they were there before too, but you have to go up one level to see
them.

It's better in 2.6.15-rc1-git5, but the menu structure is still a little
messed up, the patch below properly indents all menu entries.

Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[LLC]: Fix compiler warnings introduced by TX window scaling changes.

Noticed by Olaf Hering.

The comparisons want a u8 here (the data type on the left-hand branch
is a u8 structure member, and the constant on the right-hand branch is
"~((u8) 128)"), but C turns it into an integer so we get:

net/llc/llc_c_ac.c: In function `llc_conn_ac_inc_npta_value':
net/llc/llc_c_ac.c:998: warning: comparison is always true due to limited range of data type
net/llc/llc_c_ac.c:999: warning: large integer implicitly truncated to unsigned type

Fix this up by explicitly recasting the right-hand branch constant
into a "u8" once more.

Signed-off-by: David S. Miller <davem@davemloft.net>

[NETFILTER] ip_conntrack: fix ftp/irc/tftp helpers on ports >= 32768

Since we've converted the ftp/irc/tftp helpers to use the new
module_parm_array() some time ago, we ware accidentially using signed data
types - thus preventing those modules from being used on ports >= 32768.

This patch fixes it by using 'ushort' module parameters.

Thanks to Jan Nijs for reporting this bug.

Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[COMPAT]: Add ext3 ioctl translations.

So things like on-line resizing et al. work.

Based almost entirely upon a patch by Guido Günther <agx@sigxcpu.org>

Signed-off-by: David S. Miller <davem@davemloft.net>

[TCP]: TCP highspeed build error

There is a compile error that crept in with the last patch of
TCP patches.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] VM: fix zone list restart in page allocatate

We must reassign z before looping through the zones kicking kswapd,
since it will be NULL if we hit an OOM condition and jump back to the
beginning again. 'z' is initially assigned before the restart: label. So
move the restart label up a little.

Signed-off-by: Jens Axboe <axboe@suse.de>

[PATCH] USB: add the anydata usb-serial driver

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: delete the nokia_dku2 driver

It was causing too many problems, and this is not the proper type of
driver for this device.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: move CONFIG_USB_DEBUG checks into the Makefile

This lets us remove a lot of code in the drivers that were all checking
the same thing.  It also found some bugs in a few of the drivers, which
has been fixed up.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: OHCI lh7a404 platform device conversion fixup

Fix an error in the OHCI lh7a404 driver after the platform device
conversion.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: Maxtor OneTouch button support for older drives

This small patch adds a device ID used by older Maxtor OneTouch drives
(the ones with blue face-plate instead of the fancy silver one used in
newer models). The button on those drives works well with the current
driver.

From: Antti Andreimann <Antti.Andreimann@mail.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] usb devio warning fix

drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: fix race in kaweth disconnect

this patch from Herbert Xu fixes a race by moving termination of
the URBs into close() exclusively.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] usb-storage: Fix detection of kodak flash readers in shuttle_usbat driver

Peter Favrholdt reported that his Kodak flash device was getting
detected as a CDROM, and he helped me track this down to the fact that
the device takes a long time (approx 440ms!) to reset.

This patch increases the delay to 500ms, which solves the problem.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: Adapt microtek driver to new scsi features

the scsi layer now uses very short sg lists. This breaks the microtek
driver. Here is a patch fixes this and some other issues.

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: pl2303: updates pl2303_update_line_status()

Updates pl2303_update_line_status() to handle X75 and SX1 Siemens mobiles

Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: pl2303: adds new IDs.

This patch adds two new Siemens mobiles IDs for the pl2303 driver.

Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: onetouch doesn't suspend yet

The onetouch support doesn't suspend correctly (leaves an interrupt
URB posted, instead of unlinking it) so for now just disable it
when PM is in the air.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: cp2101.c: Jablotron usb serial interface identification

Jablotron usb serial interface identification

Signed-off-by: Josef Balatka <balatka@email.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: kill unneccessary usb-storage blacklist entries

I actually have this device, and kernel reports blacklist entry is no
longer neccessary.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: usbdevfs_ioctl 32bit fix

drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast

NFI if this is correct...

Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] usbfs: usbfs_dir_inode_operations cleanup

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: Delete leftovers from bluetty driver

This patch deletes the bluetooth.txt help file of the bluetty driver and
hands over its major device nodes for character devices to the RFCOMM TTY
implementation of the Bluetooth subsystem.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: fix 'unused variable' warning

USB: fix 'unused variable' warning

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: wacom tablet driver update

This patch adds support for Graphire4, Cintiq 710, Intuos3 6x11, etc. and
report Device IDs.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: add new wacom devices to usb hid-core list

This patch adds support for Graphire4, Cintiq 710, Intuos3 6x11, etc.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB Serial: rename ChangeLog.old

People are complaining about a .old file in the tree.  So rename
drivers/usb/serial/ChangeLog.old to ChangeLog.history.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] USB: fix build breakage in dummy_hcd.c

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Fix IXP4xx I2C driver build breakage

Platform device conversion missed a couple of spots.

Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

x86: Fix silly typo in recent <asm/signal.h> fixes

The second __const_sigaddset() should have been a sigdelset..  Compile
trouble noted by Greg K-H.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge /pub/scm/linux/kernel/git/davem/net-2.6

Merge master.kernel.org:/home/rmk/linux-2.6-arm

Merge branch 'upstream-fixes' of /linux/kernel/git/jgarzik/libata-dev

[PATCH] x86: fix sigaddset() inline asm memory constraint

Due to incomplete memory constraints, gcc would miscompile code with
sigaddset on i386 if sig arg was const.

A quote form Jakub to make the issue clear:

 "You need either
__asm__("btsl %1,%0" : "+m"(*set) : "Ir"(_sig-1) : "cc");
  or
__asm__("btsl %1,%0" : "=m"(*set) : "Ir"(_sig-1), "m"(*set) : "cc");
  because the btsl instruction doesn't just set the memory to some
  value, but needs to read its previous content as well.  If you don't
  tell that fact to GCC, GCC is of course free to optimize as if the asm
  was just setting the value and not depended on the previous value."

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ipw2200: fix error log offset calculation

This fixes a slab corruption issue in the ipw2200 driver: it essentially
multiplied the error log number _twice_ by the size of the error element
entry (once explicitly in the code, and once implicitly as part of the
regular pointer arithmetic).

Cc: Henrik Brix Andersen <brix@gentoo.org>
Cc: Bernard Blackham <bernard@blackham.com.au>
Cc: Zilvinas Valinskas <zilvinas@gemtek.lt>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
--

[PATCH] ipw2200: disallow direct scanning when device is down

The function ipw_request_direct_scan() should bail out when the device
is down.  This fixes a lockup caused by wpa_supplicant triggering
ipw_request_direct_scan() while the driver was in a middle of a reset
due to firmware errors.

Thanks to Zilvinas Valinskas for reporting the bug and helping me
debug it.

Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[MIPS] Update defconfigs

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SEAD: More build fixes.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] TX3927: Try to glue the PCI code.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SEAD: Delete seadint_init() prototype.

There is no definition for seadint_init() and the unprotected prototype
breaks compilation of assembler files.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Ocelot G: Use CPU_MASK_NONE instead of 0 to initialize cpu mask.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] JMR3927: Fix include wrapper symbol.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] JMR3927: Fix compilation by including <linux/ds1742rtc.h>.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] JMR3927: need include/asm-mips/mach-jmr3927 in it's include path.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] JMR3927: It's ops-tx3927.o not ops-jmr3927.o

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[IDE] Add driver for Sibyte Swarm evaluation board

This driver supports the IDE port on the Sibyte Swarm evaluation boards
and it's relatives for the BCM1250 family of systems on a chip.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

[MIPS] Alchemy: Console output fixup

This is needed to make console output appear with the new driver...

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix documentation typos.

Signed-off-by: Arnaud Giersch <arnaud.giersch@free.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Add const qualifier to writes##bwlq.

Add const qualifier to parameter addr of writes##bwlq.

Signed-off-by: Arnaud Giersch <arnaud.giersch@free.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] IP32: Fix sparse warnings.

Add __iomem qualifier to crime and mace pointers.

Signed-off-by: Arnaud Giersch <arnaud.giersch@free.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] IP32 Fix and complete IP32 parport definitions

Fix, complete, and indent IP32 parport definitions.
Definition were wrong for CTXINUSE and DMACTIVE (1-bit shift).
Add macros DATA_BOUND, DATALEN_SHIFT, and CTRSHIFT.

Signed-off-by: Arnaud Giersch <arnaud.giersch@free.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] IP32: Export mace symbol.

Export mace symbol so that it can be used in modules.

Signed-off-by: Arnaud Giersch <arnaud.giersch@free.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] JMR3927: Fix syntax error.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] JMR3927: Undo accidental rename.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] DDB5477: Fix unused variable warning.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>