Arnd Bergmann [Fri, 23 May 2014 21:46:50 +0000 (23:46 +0200)]
Merge tag 'sunxi-dt-for-3.16-2' of https://github.com/mripard/linux into for-next
Merge "Allwinner DT changes for 3.16, take 2" from Maxime Ripard:
- Introduction of a new board, the i12-tvbox
- Enable the MMC and USB controllers on the Colombus
- Add the enable-method to the A31 cpus
- a few fixes
* tag 'sunxi-dt-for-3.16-2' of https://github.com/mripard/linux:
ARM: dts: sun7i: Add new i12-tvbox board
ARM: dts: sun7i: cubietruck: set mmc3 bus-width property
ARM: sun6i: Add MMC0 controller to the Colombus board
ARM: sun6i: Fix OHCI2 node name
ARM: sun6i: Enable USB Host support on the Colombus board
ARM: sunxi: Add fixed 3V regulator
ARM: sun6i: Define the A31 CPUs enable-method
ARM: sunxi: dt: build DTs according to new MACH_SUNxI Kconfig symbols
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/boot/dts/Makefile
Arnd Bergmann [Fri, 23 May 2014 21:33:19 +0000 (23:33 +0200)]
Merge tag 'for-3.16/bcm-dt' of git://github.com/broadcom/mach-bcm into for-next
Merge "mach-bcm dt updates for 3.16" from Matt Porter:
* Add PWM support to bcm281xx and bcm28155 ap board
* Add gpldo and vbus regulators to bcm590xx
* tag 'for-3.16/bcm-dt' of git://github.com/broadcom/mach-bcm:
ARM: dts: bcm590xx: add support for GPLDO and VBUS regulators
ARM: dts: Enable the PWM for bcm28155 AP board
ARM: dts: Declare the PWM for bcm11351 (bcm281xx)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 23 May 2014 21:30:17 +0000 (23:30 +0200)]
Merge tag 'qcom-dt-for-3.16' of git://git./linux/kernel/git/galak/linux-qcom into for-next
Merge "Qualcomm ARM Based Device Tree Updates for v3.16" from Kumar Gala:
* Added device tree nodes for pinctrl and SDHC for msm8974 SoC/DB8074 board
* Added binding spec for GSBI configuration node
* tag 'qcom-dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
soc: qcom: Add device tree binding for GSBI
ARM: dts: msm: Add SDHC controller nodes for MSM8974 and DB8074 board
ARM: dts: MSM8974: Add pinctrl node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 23 May 2014 21:02:49 +0000 (23:02 +0200)]
Merge tag 'at91-dt3' of git://github.com/at91linux/linux-at91 into next/dt
3.16 third DT series:
- move of both at91sam9n12 and at91sam9x5 to CCF
* tag 'at91-dt3' of git://github.com/at91linux/linux-at91:
ARM: at91: move sam9n12 SoC to the CCF
ARM: at91/dt: define sam9n12ek crystal frequencies
ARM: at91/dt: define sam9n12 clocks
ARM: at91: prepare common clk transition for sam9n12 SoC
ARM: at91: move sam9x5 SoCs to the CCF
ARM: at91/dt: define sam9x5ek's crystal frequencies
ARM: at91/dt: define sam9x5 clocks
ARM: at91: prepare common clk transition for sam9x5 SoCs
dt-bindings: clock: Move at91.h to dt-bindigs/clock
ARM: at91: fix spi cs on sama5d3 Xplained board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 23 May 2014 20:59:20 +0000 (22:59 +0200)]
Merge branch 'at91/cleanup' into next/dt
Conflicts:
arch/arm/boot/dts/at91sam9rl.dtsi
Needed as a dependency for the at91/dt2 branch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 23 May 2014 20:35:56 +0000 (22:35 +0200)]
Merge tag 'sti-dt-for-v3.16-1' of git://git.stlinux.com/devel/kernel/linux-sti into next/dt
Merge "ARM: STi: DT changes for v3.16, v3" from Maxime Coquelin:
Please consider these STi DT updates for v3.16.
This 3rd version takes into account Olof's comments on the v2:
- Fix upper-cases in labels and node names
- Sort compatibles order from specific to generic
- Sort dts entries in Makefile
It also adds support for the B2020 revision E board for STiH416 SoC.
Note that two reset patches are part of this pull request, in order to avoid
compilation breakage.
Adding these two patches in this pull request has been accepted by Philipp Zabel.
* tag 'sti-dt-for-v3.16-1' of git://git.stlinux.com/devel/kernel/linux-sti: (23 commits)
ARM: sti: stih41x: Provide a proper header for this DTSI file
ARM: sti: stih416: Enable board LED support for B2020 RevE
ARM: sti: stih416: Add support for B2020 RevE
ARM: STi: DT: STiH41x Add clk_ignore_unused to bootargs
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A9
ARM: STi: DT: STiH415: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
ARM: STi: DT: STiH415: Remove unused CLK_S_ICN_REG_0 fixed clock
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A0/1/10/11/12
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A9/DDR/GPU
ARM: STi: DT: STiH416: 416 DT Entry for clockgen B/C/D/E/F
ARM: STi: DT: STiH416: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
ARM: STi: DT: STiH416: Remove unused CLK_S_ICN_REG_0 fixed clock
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A0/1/10/11/12
ARM: STi: DT: STiH41x: Rename CLK_SYSIN into clk_sysin
ARM: STi: DT: add keyscan for stih41x-b2000
ARM: STi: DT: add keyscan for stih416
ARM: STi: DT: add keyscan for stih415
driver: reset: sti: add keyscan for stih416
driver: reset: sti: add keyscan for stih415
ARM: dts: STiH407: Add B2120 board support
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Andy Gross [Thu, 24 Apr 2014 16:31:20 +0000 (11:31 -0500)]
soc: qcom: Add device tree binding for GSBI
Add device tree binding support for the QCOM GSBI driver.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Matt Porter [Fri, 11 Apr 2014 12:35:43 +0000 (08:35 -0400)]
ARM: dts: bcm590xx: add support for GPLDO and VBUS regulators
Adds additional nodes to support GPLDO1-6 and VBUS regulators which
are now supported in the bcm590xx regulator driver.
Signed-off-by: Matt Porter <mporter@linaro.org>
Georgi Djakov [Fri, 31 Jan 2014 14:21:56 +0000 (16:21 +0200)]
ARM: dts: msm: Add SDHC controller nodes for MSM8974 and DB8074 board
Add support for the 2 SDHC controllers on the DB8074 board. The first
controller (at 0xf9824900) is connected to an on board soldered eMMC.
The second controller (at 0xf98a4900) is connected to a uSD card slot.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Ivan T. Ivanov [Thu, 6 Feb 2014 15:28:49 +0000 (17:28 +0200)]
ARM: dts: MSM8974: Add pinctrl node
Add the pin control node and pin definitions of SPI8.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Boris BREZILLON [Mon, 12 May 2014 16:26:30 +0000 (18:26 +0200)]
ARM: at91: move sam9n12 SoC to the CCF
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9n12 SoC support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 12 May 2014 16:26:29 +0000 (18:26 +0200)]
ARM: at91/dt: define sam9n12ek crystal frequencies
Define sam9n12ek's main and slow crystal frequencies.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 12 May 2014 16:26:28 +0000 (18:26 +0200)]
ARM: at91/dt: define sam9n12 clocks
Define sam9n12 clocks and make use of them in peripheral definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 12 May 2014 16:26:27 +0000 (18:26 +0200)]
ARM: at91: prepare common clk transition for sam9n12 SoC
This patch encloses sam9n12 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 12 May 2014 16:23:37 +0000 (18:23 +0200)]
ARM: at91: move sam9x5 SoCs to the CCF
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9x5 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 12 May 2014 16:23:36 +0000 (18:23 +0200)]
ARM: at91/dt: define sam9x5ek's crystal frequencies
Define sam9x5ek's main and slow crystal frequencies.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 12 May 2014 16:23:35 +0000 (18:23 +0200)]
ARM: at91/dt: define sam9x5 clocks
Define sam9x5 clocks in sam9x5 dt files and make use of them in peripheral
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 12 May 2014 16:23:34 +0000 (18:23 +0200)]
ARM: at91: prepare common clk transition for sam9x5 SoCs
This patch encloses sam9x5 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Thu, 22 May 2014 16:01:22 +0000 (18:01 +0200)]
Merge branch 'at91-3.16-cleanup' into at91-3.16-dt3
Nicolas Ferre [Thu, 22 May 2014 15:36:07 +0000 (17:36 +0200)]
Merge branch 'at91-3.15-fixes' into at91-3.16-dt3
Hans de Goede [Wed, 21 May 2014 17:43:31 +0000 (19:43 +0200)]
ARM: dts: sun7i: Add new i12-tvbox board
The i12 tvbox is an A20 based android tvbox, with 512M / 1G RAM, 4G nand flash,
ap6210 or ap6330 sdio wifi + bt (broadcom sdio wifi + uart attached brcm bt),
2USB host ports using USB-A receptacles and a micro-usb receptacle for USB OTG,
and 100Mbit ethernet using an IP101a phy.
The PCB is labelled i12-a20 hence I've named the board i12-a20. It is used
in noname allwinner A20 tv-boxes, which are sometimes sold with Q5 or
QT840A as product name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Wed, 21 May 2014 17:43:30 +0000 (19:43 +0200)]
ARM: dts: sun7i: cubietruck: set mmc3 bus-width property
bus-width defaults to 1, and all 4 lines are hooked up at the cubietruck,
properly set bus-width to 4.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Wed, 21 May 2014 08:23:20 +0000 (10:23 +0200)]
ARM: sun6i: Add MMC0 controller to the Colombus board
The Colombus has a full size SD slot wired to the MMC0 controller. In order to
work, the MMC lines have to have the pull-ups enabled though.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Tue, 20 May 2014 11:59:58 +0000 (13:59 +0200)]
ARM: sun6i: Fix OHCI2 node name
The unit-address doesn't match the reg property. Since the reg property is
correct, change the unit-address accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 20 May 2014 11:59:15 +0000 (13:59 +0200)]
ARM: sun6i: Enable USB Host support on the Colombus board
The colombus board has a on-board USB hub, that is enabled through the pin
PH24, and wired to the first EHCI controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olof Johansson [Thu, 22 May 2014 05:45:52 +0000 (22:45 -0700)]
Merge tag 'samsung-dt' of git./linux/kernel/git/kgene/linux-samsung into next/dt
Samsung DT updates for v3.16
- exynos4
: add missing pinctrls
- exynos4412-trats2
: update camera nodes and add rear camera nodes
: rename alias for i2c_ak8975 label
Update camera nodes for exynos4 and exynos4412-trats2
- exynos5250
: update DWC3 usb controller and enable to use generic USB DRD phy
- exynos5250-snow
: enable dp-controller, fimd, hdmi and pwm backlight
: add sound node and Vbus regulator for USB 3.0
: add tps65090 power regulator
: add pinctrl for EC irq and i2c-arbitrator
- exynos5420
: change to correct compatible string for hdmi
: add PD entry to MFC codec and enable DWC3 and USB 3.0 PHY
: add MFC memory banks for smdk5420 and arndale-octa boards
- exynos5420-peach-pit
: add support exynos5420 based peach-pit board
: add sound node and Vbus regulatro for USB 3.0
: enable dp-controller, fimd
- exynos5420-smdk5420
: add Vbus regulatro for USB 3.0
- use generic DT bindings for map SYSRAM
[olof: Fixed up conflict with a fix for 4212 secondary CPU startup, carrying
over the fix to the reworked code]
* tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: dts: Add MFC memory banks to exynos5420 boards
ARM: dts: enable dp-controller for exynos5420-peach-pit board
ARM: dts: enable fimd for exynos5420 based peach-pit board
ARM: dts: enable dp-controller for exynos5250-snow board
ARM: dts: enable fimd for exynos5250-snow board
ARM: dts: enable pwm backlight for exynos5250-snow
ARM: dts: Add pwmX_out pinctrl nodes to exynos5250
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-smdk5420
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-peach-pit
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5250-snow
ARM: dts: Add PD entry to MFC codec on exynos5420
ARM: dts: Add sound node for exynos5420-peach-pit board
ARM: dts: Add sound node for exynos5250-snow board
ARM: dts: Update DWC3 usb controller to use new phy driver for exynos5250
ARM: dts: Enable support for generic USB DRD phy for exynos5250
ARM: dts: Enable support for DWC3 controller for exynos5420
ARM: dts: Enable support for USB 3.0 PHY controller for exynos5420
ARM: dts: enable hdmi for exynos5420-peach-pit board
ARM: dts: change to correct compatible string for exynos5420 hdmi
ARM: dts: enable hdmi for exynos5250 based snow board
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 22 May 2014 05:41:50 +0000 (22:41 -0700)]
Merge commit '
702b691e4a71' into next/dt
Merging in Samsung fixes for 3.15-rc to avoid an annoying context conflict
with new DT code.
* commit '
702b691e4a71':
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 21 May 2014 22:06:16 +0000 (15:06 -0700)]
Merge tag 'tegra-for-3.16-dt' of git://git./linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: device tree changes for 3.16" from Stephen Warren:
The bulk of Tegra changes for 3.16 are to device trees. Highlights are:
- New board support for:
- Jetson TK1.
- SHIELD.
- Tegra Note 7.
- Colibri T30 module.
- HDMI support on Venice2.
- SD card write-protect GPIOs added to some boards.
- Numerous regulator cleanups.
* tag 'tegra-for-3.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: initial add of Colibri T30
ARM: tegra: add device tree for SHIELD
ARM: tegra: add SD wp-gpios to Venice2 DT
ARM: tegra: add Tegra Note 7 device tree
ARM: tegra: add SD wp-gpios to Dalmore DT
ARM: tegra: add SD wp-gpios to Jetson TK1 DT
ARM: tegra: use correct audio CODEC on Jetson TK1
ARM: tegra: dalmore - Add DSI power supply
ARM: tegra: dalmore - Add +5V HDMI supply
ARM: tegra: beaver - Add +5V HDMI supply
ARM: tegra: harmony - Add +5V HDMI supply
ARM: tegra: jetson-tk1 - Enable HDMI support
ARM: tegra: venice2 - Enable HDMI
ARM: tegra: Add Tegra124 HDMI support
ARM: tegra: fix Venice2 SD card VQMMC supply
ARM: tegra: make Venice's +3.3V_RUN regulator always on
ARM: tegra: fix Jetson TK1 SD card supply
ARM: tegra: define Jetson TK1 regulators
ARM: tegra: add Jetson TK1 device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 21 May 2014 21:59:21 +0000 (14:59 -0700)]
Merge tag 'imx-dt-3.16' of git://git./linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree changes for 3.16" from Shawn Guo:
i.MX device tree changes for 3.16:
- New board support: imx35-pdk, imx51-digi-connectcore, imx6dl-phytec,
imx6dl-riotboard, and vf610-colibri.
- Improve device tree support for imx51-babbage and eukrea-cpuimx51 to
get the same level support as board files, so that we can kill the
board files.
- Quite some updates on imx27-phytec-phycore board support from
Alexander Shiyan
- Enable USB, sound and touchscreen on the eukrea imx25/35/51 boards,
from Denis Carikli
- Quite a lot of patches from Fabio Estevam, updating Freescale
imx25-pdk and imx27-pdk board support
- Correct USB device configuration for imx25/35
- Fixes i2c4 device node in imx6dl.dtsi regarding to compatible string
and clock data
- Enable HDMI, TVE, LVDS display support on a bunch of imx5/6 boards
- Update PCIe to the new binding and enable PCIe support on
imx6qdl-sabresd board
- A couple of imx6q-dmo-edmqmx6 updates from Lucas Stach, adding pfuze
irq gpio and SPI flash
- Enable CODA7541 VPU for i.MX53
- A series of updates on imx6qdl-phytec boards from Philipp Zabel
- Small cleanups and fixes on board imx28-duckbill - Michael Heimpold
- Add stdout-path property to i.MX boards
- Karo TX25 board updates from Sascha Hauer
- Enable pwm and sdhc devices for board vf610-twr
* tag 'imx-dt-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (105 commits)
ARM: dts: imx35-pdk: Fix memory region description
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: Add CAN support
ARM: dts: imx6: add new board RIoTboard
ARM: dts: imx6: i2c4 cleanup
ARM: dts: imx6: edmqmx6: add vcc and vio power supplies to stmpe
ARM: dts: Karo TX25: use hardware ecc
ARM: dts: Karo TX25: Add phy reset gpio and supply for FEC
ARM: dts: Karo TX25: Add pinctrl nodes
ARM: dts: i.MX25: Add IRAM node
ARM: dts: i.MX25: Add mmc aliases
ARM: dts: i.MX51 babbage: Fix FEC pad ctrl settings
ARM: dts: imx6qdl-sabresd: Add USDHC4 support
ARM: imx: add HDMI support for SolidRun HummingBoard and Cubox-i
ARM: dts: imx6: edmqmx6: add SPI bus and flash
ARM: dts: imx6: edmqmx6: add pinctrl for pfuze irq gpio
ARM: dts: imx6q-udoo: Add HDMI support
ARM: dts: Add stdout-path property to i.MX boards
ARM: dts: imx: Fix LVDS mapping for Ventana GW52xx
ARM: dts: imx: add LVDS backlight for Ventana
ARM: dts: imx6qdl-sabresd: remove power-on gpio from pcie
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 21 May 2014 21:36:06 +0000 (14:36 -0700)]
Merge tag 'sunxi-dt-for-3.16' of https://github.com/mripard/linux into next/dt
Merge "Allwinner DT additions for 3.16" from Maxime Ripard:
- Introduction of the MMC controlers
- New board: A10s R7, Mele M9, APP4-EVB1
- Enabled the PMU on the Cortex A7-based SoCs
* tag 'sunxi-dt-for-3.16' of https://github.com/mripard/linux: (38 commits)
ARM: sunxi: dt: declare the r_pio pin controller for A31 SoC
ARM: sunxi: dt: add PRCM clk and reset controller subdevices
ARM: sunxi: dt: add APP4-EVB1 board support
ARM: sun6i: dt: Add support for the USB controllers
ARM: sun6i: Add the USB clocks to the DTSI
ARM: dts: sun5i: Add new A10s r7 hdmi tv dongle board
ARM: dts: sun7i: Add reg_vcc3v3 to sun7i board mmc nodes
ARM: dts: sun6i: Add reg_vcc3v3 to sun6i board mmc nodes
ARM: dts: sun5i: Add reg_vcc3v3 to sun5i board mmc nodes
ARM: dts: sun4i: Add reg_vcc3v3 to sun4i board mmc nodes
ARM: dts: sunxi: Add reg_vcc3v3 supply to sunxi-common-regulators.dtsi
ARM: dts: sun7i: Add basic support for the Cubietruck WiFi module
ARM: dts: sun7i: Enable mmc controller on various A20 boards
ARM: dts: sun7i: Add pin-muxing info for the mmc controllers
ARM: dts: sun7i: Add mmc controller nodes
ARM: dts: sun6i: Add new sun6i-a31-m9 dts file for Mele M9
ARM: dts: sun6i: Add mmc controller nodes
ARM: dts: sun6i: Add mmc clocks
ARM: dts: sun5i: Enable mmc controller on various A10s and A13 boards
ARM: dts: sun5i: Add mmc controller nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Lee Jones [Wed, 21 May 2014 08:45:00 +0000 (10:45 +0200)]
ARM: sti: stih41x: Provide a proper header for this DTSI file
Just a trivial commenting fix. No functional changes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Lee Jones [Wed, 21 May 2014 08:45:00 +0000 (10:45 +0200)]
ARM: sti: stih416: Enable board LED support for B2020 RevE
There are two LEDs available on the B2020 RevE board, one red, one
green. In this patch we enable the red one for "heartbeat" and turn
the green one off.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Lee Jones [Wed, 21 May 2014 08:45:00 +0000 (10:45 +0200)]
ARM: sti: stih416: Add support for B2020 RevE
The B2020 RevE differs from the other B2020 boards in a few subtle ways;
including the Ethernet reset GPIO which this patch adds support for and
the LED wiring which will follow in a latter patch. Without supplying
these differences Ethernet and the board LEDs simply will not work.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH41x Add clk_ignore_unused to bootargs
Interconnect clocks are not yet managed at the init, then
we have to start the kernel with clk_ignore_unused.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A9
Patch adds DT entries for clockgen A9
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH415: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
CLK_S_GMAC0_PHY & CLK_S_ETH1_PH clocks are no longer used.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH415: Remove unused CLK_S_ICN_REG_0 fixed clock
CLK_S_ICN_REG_0 clock is no longer used.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A0/1/10/11/12
Patch adds DT entries for clockgen A0/1/10/11/12
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A9/DDR/GPU
Patch adds DT entries for clockgen A9/DDR/GPU
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH416: 416 DT Entry for clockgen B/C/D/E/F
Patch adds DT entries for clockgen B/C/D/E/F
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH416: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
CLK_S_GMAC0_PHY & CLK_S_ETH1_PH clocks are no longer used.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH416: Remove unused CLK_S_ICN_REG_0 fixed clock
CLK_S_ICN_REG_0 clock is no longer used.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A0/1/10/11/12
Patch adds DT entries for clockgen A0/1/10/11/12
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Tue, 20 May 2014 13:22:00 +0000 (15:22 +0200)]
ARM: STi: DT: STiH41x: Rename CLK_SYSIN into clk_sysin
all-caps node name is not very usual.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Fri, 11 Apr 2014 15:07:00 +0000 (17:07 +0200)]
ARM: STi: DT: add keyscan for stih41x-b2000
Add keyscan setup for stih415/h416 b2000.
Both have same raw/column lines number, debounce time and keymap.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Fri, 11 Apr 2014 15:07:00 +0000 (17:07 +0200)]
ARM: STi: DT: add keyscan for stih416
Add keyscan support for stih416.
It is disabled by default given that it is not enabled on all boards.
Also there are PIOs conflict with already claimed lines.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Fri, 11 Apr 2014 15:07:00 +0000 (17:07 +0200)]
ARM: STi: DT: add keyscan for stih415
Add keyscan support for stih415.
It is put disabled by default because it is not enabled on all boards
Also there are PIOs conflict with already claimed lines.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Fri, 11 Apr 2014 15:07:00 +0000 (17:07 +0200)]
driver: reset: sti: add keyscan for stih416
Add keyscan reset on stih416 reset controller.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Fri, 11 Apr 2014 15:07:00 +0000 (17:07 +0200)]
driver: reset: sti: add keyscan for stih415
Add keyscan reset on stih415 reset controller.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime Coquelin [Thu, 27 Feb 2014 12:33:27 +0000 (13:33 +0100)]
ARM: dts: STiH407: Add B2120 board support
B2120 HDK is the reference board for STiH407 SoC.
It has the following characteristics:
- 1GB DDR3
- 8GB eMMC / SD-Card slot
- 32MB NOR Flash
- 1 x Gbit Ethernet
- 1 x USB 3.0 port
- 1 x Mini-PCIe
- 1 x SATA
- 1 x HDMI output
- 1 x HDMI input
- 1 x SPDIF
This patch only introduces basic functionnalities, such as I2C and UART.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime Coquelin [Thu, 27 Feb 2014 12:27:27 +0000 (13:27 +0100)]
ARM: dts: Add STiH407 SoC support
The STiH407 is advanced multi-HD AVC processor with 3D graphics acceleration
and 1.5-GHz ARM Cortex-A9 SMP CPU.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime Coquelin [Tue, 20 May 2014 09:10:54 +0000 (11:10 +0200)]
ARM: dts: Fix STi boards compatibles
The compatible strings have to be ordered from specific to generic.
This patch fixes this for STi boards, which did the exact opposite.
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime Coquelin [Tue, 20 May 2014 09:01:53 +0000 (11:01 +0200)]
ARM: dts: Sort STi boards in Makefile
The boards have to be sorted in alphanumerical order in the Makefile.
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime Ripard [Tue, 20 May 2014 15:47:45 +0000 (17:47 +0200)]
ARM: sunxi: Add fixed 3V regulator
A few boards we've seen have a fixed 3V regulator. Add this one on the common
DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Olof Johansson [Tue, 20 May 2014 06:00:25 +0000 (23:00 -0700)]
Merge tag 'renesas-dt3-for-v3.16' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Third Round of Renesas ARM Based SoC DT Updates for v3.16" from Simon
Horman:
r8a7791 (R-Car M2), r8a7779 (R-Car H1), r8a7778 (R-Car M1),
r8a7740 (R-Mobile A1) and r8a73a4 (R-Mobile APE6) SoCs
* Move interrupt-parent property to root node
r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCs
* Add GPIO clocks
r8a7791 (R-Car M2) based Henninger board
* Add MSIOF0, QSPI and SDHI0/2 support
* Specify EXTAL frequency
r8a7779 (R-Car H1) based Marzen board
* Set SMSC lan to use irq-push-pull
r8a7740 (R-Mobile A1) SoC
* Remove duplicate interrupt-parent property
r8a7740 (R-Mobile A1) based Armadillo800 EVA board
* Add Ethernet support
* tag 'renesas-dt3-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740 dtsi: Remove duplicate interrupt-parent property
ARM: shmobile: marzen-reference: Set SMSC lan to use irq-push-pull
ARM: shmobile: r8a7791 dtsi: Add GPIO clocks
ARM: shmobile: r8a7790 dtsi: Add GPIO clocks
ARM: shmobile: dts: Move interrupt-parent property to root node
ARM: shmobile: armadillo-reference dts: Add Ethernet support
ARM: shmobile: r8a7740 dtsi: Add Ethernet support
ARM: shmobile: henninger: add MSIOF0 DT support
ARM: shmobile: henninger: add QSPI DT support
ARM: shmobile: henninger: add SDHI0/2 DT support
ARM: shmobile: henninger: specify EXTAL frequency
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 20 May 2014 05:46:00 +0000 (22:46 -0700)]
Merge tag 'at91-dt2' of git://github.com/at91linux/linux-at91 into next/dt
Merge "at91: DT for 3.16 #2" from Nicolas Ferre:
3.16: second DT series:
- at91sam9rl and at91sam9261 fixes about PLL ranges
- at91sam9261 more comprehensive support for SSC
- sama5d3 Xplained: addition of pull-ups, PWM and PMIC (regulator)
* tag 'at91-dt2' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: at91-sama5d3_xplained: add the regulator device node
ARM: at91: add 2 PWM outputs to SAMA5D3 Xplained
ARM: at91: add PWM pinctrl to SAMA5D3
ARM: at91: add pull-up to i2c[02] on SAMA5D3 Xplained
ARM: at91/dt: sam9rl: Fix PLL output range and mck divisors
ARM: at91/dt: sam9261: Add ssc2, SSC clocks and pcks
ARM: at91/dt: sam9261: Fix PLL output ranges and other clocks divisors
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 20 May 2014 05:23:48 +0000 (22:23 -0700)]
Merge tag 'keystone-dts' of git://git./linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "ARM: Keystone DTS updates for 3.16" from Santosh Shilimkar:
Keystone DTS updates for 3.16
- Few of address cell warning fixes.
- Add Lamarr and Edision EVM NOR flash and NAND devices.
- Update dts to make use of dma-ranges and dma-coherent properties.
* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-evm: add spi nor flash support
ARM: dts: k2l-evm: add AEMIF/NAND device entry
ARM: dts: k2e-evm: add AEMIF/NAND device entry
ARM: dts: keystone: Update USB node for dma properties
ARM: dts: keystone: Use dma-ranges property
ARM: dts: keystone: add cell's information to spi nodes
ARM: dts: keystone: move i2c0 device node from SoC to board files
ARM: dts: keystone: add cell's information to i2c nodes
ARM: dts: keystone: drop address and size cells from GIC node
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 20 May 2014 05:02:16 +0000 (22:02 -0700)]
Merge tag 'v3.16-rockchip-dt' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: devicetree changes for v3.16" from Heiko Stübner:
Addition of missing board compatible names and their vendor-prefixes
as well as the dts portions of the pinctrl rework.
* tag 'v3.16-rockchip-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: convert pinctrl nodes to new bindings
ARM: dts: rockchip: add root compatible properties
of: add mundoreader and radxa vendor prefixes
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 20 May 2014 04:55:03 +0000 (21:55 -0700)]
Merge tag 'mvebu-dt-3.16' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: DT changes for v3.16" from Jason Cooper:
mvebu DT changes for v3.16
- kirkwood
- rework nsa3x0 board to add nsa320
- large cleanup to facilitate use in barebox
- guruplug phy updates
- audio updates for t5325
- mvebu
- use clocks vice clock-frequency for uart nodes
- armada 375/380/385
- add watchdog node
- add coherency fabric
- add smp support
- add sdhci
- add ahci
- add thermal sensor
- armada 370/XP
- and pmsu
* tag 'mvebu-dt-3.16' of git://git.infradead.org/linux-mvebu: (35 commits)
ARM: Kirkwood: t5325: Use simple card to instantiate audio
ARM: Kirkwood: DT: Add missing #sound-dai-cells property
ARM: Kirkwood: Add node for audio codec
ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id
ARM: dts: kirkwood: set Guruplug ethernet PHY compatible
ARM: dts: kirkwood: set default pinctrl for I2C1 on 6282
ARM: dts: kirkwood: set default pinctrl for I2C0
ARM: dts: kirkwood: set default pinctrl for NAND
ARM: dts: kirkwood: set default pinctrl for SPI0
ARM: dts: kirkwood: set default pinctrl for UART0/1
ARM: dts: kirkwood: set default pinctrl for GBE1
ARM: dts: kirkwood: consolidate common pinctrl settings
ARM: dts: kirkwood: add pinctrl node to common SoC include
ARM: dts: kirkwood: rename pin-controller nodes
ARM: dts: kirkwood: remove clock-frequency properties from UART nodes
ARM: dts: kirkwood: add stdout-path property to all boards
ARM: dts: kirkwood: add node labels
ARM: mvebu: Enable the thermal sensor in Armada 380/385 SoC
ARM: mvebu: Enable the thermal sensor in Armada 375 SoC
ARM: mvebu: don't use clocks property in UART node for Netgear RN2120
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Sachin Kamat [Mon, 19 May 2014 16:04:13 +0000 (01:04 +0900)]
ARM: dts: Add MFC memory banks to exynos5420 boards
Add MFC memory banks to Exynos5420 based SMDK and Arndale-octa boards.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rahul Sharma [Mon, 19 May 2014 14:01:46 +0000 (23:01 +0900)]
ARM: dts: enable dp-controller for exynos5420-peach-pit board
Enable dp-controller for peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rahul Sharma [Mon, 19 May 2014 14:01:18 +0000 (23:01 +0900)]
ARM: dts: enable fimd for exynos5420 based peach-pit board
Enable fimd for peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rahul Sharma [Mon, 19 May 2014 13:58:47 +0000 (22:58 +0900)]
ARM: dts: enable dp-controller for exynos5250-snow board
Enable dp-controller for snow board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rahul Sharma [Mon, 19 May 2014 13:56:49 +0000 (22:56 +0900)]
ARM: dts: enable fimd for exynos5250-snow board
Enable fimd node for snow board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ajay Kumar [Mon, 19 May 2014 13:38:18 +0000 (22:38 +0900)]
ARM: dts: enable pwm backlight for exynos5250-snow
Add PWM backlight node for exynos5250 based snow board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ajay Kumar [Mon, 19 May 2014 13:38:17 +0000 (22:38 +0900)]
ARM: dts: Add pwmX_out pinctrl nodes to exynos5250
Adds the PWM nodes to 5250 pinctrl dtsi file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vivek Gautam [Mon, 19 May 2014 13:30:48 +0000 (22:30 +0900)]
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-smdk5420
Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vivek Gautam [Mon, 19 May 2014 13:29:42 +0000 (22:29 +0900)]
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-peach-pit
Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vivek Gautam [Mon, 19 May 2014 13:23:43 +0000 (22:23 +0900)]
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5250-snow
Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Sachin Kamat [Fri, 16 May 2014 22:57:10 +0000 (07:57 +0900)]
ARM: dts: Add PD entry to MFC codec on exynos5420
PD entry was missing in MFC codec node.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by : Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tushar Behera [Fri, 16 May 2014 22:44:10 +0000 (07:44 +0900)]
ARM: dts: Add sound node for exynos5420-peach-pit board
The audio setup on Peach-pit board is similar to Snow board, hence the
sound-card driver used on Snow board can be reused on Peach-pit board.
Peach-pit board uses MAX98090 audio codec.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tushar Behera [Fri, 16 May 2014 22:43:18 +0000 (07:43 +0900)]
ARM: dts: Add sound node for exynos5250-snow board
The audio codec on Snow board, MAX98095 is connected on I2C7 bus.
Also it requires the GPX1-7 line to be pulled up.
Updated Snow DTS file to incorporate above changes and added a
sound node to instantiate the I2S-based sound card.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vivek Gautam [Thu, 15 May 2014 21:38:15 +0000 (06:38 +0900)]
ARM: dts: Update DWC3 usb controller to use new phy driver for exynos5250
Removing the dt node for older usb3 phy driver from Exynos5250
device tree and updating the dt node for DWC3 controller to
use new phy driver based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vivek Gautam [Thu, 15 May 2014 21:38:10 +0000 (06:38 +0900)]
ARM: dts: Enable support for generic USB DRD phy for exynos5250
Add device tree node for new usbdrd-phy driver, which
is based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vivek Gautam [Thu, 15 May 2014 21:38:01 +0000 (06:38 +0900)]
ARM: dts: Enable support for DWC3 controller for exynos5420
Add device tree nodes for DWC3 controller present on
Exynos 5420 SoC, to enable support for USB 3.0.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vivek Gautam [Thu, 15 May 2014 21:37:03 +0000 (06:37 +0900)]
ARM: dts: Enable support for USB 3.0 PHY controller for exynos5420
Add device tree nodes for USB 3.0 PHY present alongwith
USB 3.0 controller Exynos 5420 SoC. This phy driver is
based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rahul Sharma [Thu, 15 May 2014 20:23:21 +0000 (05:23 +0900)]
ARM: dts: enable hdmi for exynos5420-peach-pit board
Enable hdmi for exynos5420 based peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rahul Sharma [Thu, 15 May 2014 20:23:16 +0000 (05:23 +0900)]
ARM: dts: change to correct compatible string for exynos5420 hdmi
Replace compatible string for HDMI node in Exynos5420. Since
latest restructring in Drm hdmi driver, it is agreed to use
a seperate compatible string for Exynos5420 HDMI IP siince it
uses APB mapped Phy.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rahul Sharma [Thu, 15 May 2014 20:22:41 +0000 (05:22 +0900)]
ARM: dts: enable hdmi for exynos5250 based snow board
Enable support for HDMI for exynos5250 based Snow board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Maxime Ripard [Fri, 18 Apr 2014 19:01:52 +0000 (21:01 +0200)]
ARM: sun6i: Define the A31 CPUs enable-method
That will allow to use the CPU_METHOD_OF_DECLARE definition we did previously.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 May 2014 13:11:20 +0000 (21:11 +0800)]
ARM: sunxi: dt: build DTs according to new MACH_SUNxI Kconfig symbols
Allwinner sunxi support has been split into the various SoCs in Kconfig.
Adapt the new symbols for the device trees.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olof Johansson [Fri, 16 May 2014 23:07:37 +0000 (16:07 -0700)]
Merge tag 'socfpga-dt-updates-for-3.16_v3' of git://git.rocketboards.org/linux-socfpga-next into next/dt
Merge "dts: socfpga: general updates for the socfpga platform" from Dinh
Nguyen:
Mostly DTS additions to the SOCFPGA platform from Steffan Trumtrar, and a
couple of device tree documentation updates/typo fix.
This one does not the GPIO binding patch, as that is pending further
discussion. Also, v3 fixes a rebase artifact and compile tested.
* tag 'socfpga-dt-updates-for-3.16_v3' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: dts: Add div-reg to the main_pll clocks
ARM: socfpga: dts: add reset-controller
Documentation: dt: reset: move socfpga-reset
Documentation: dt: socfpga: add reset-cells property
ARM: socfpga: dts: Add DTS entries for USB
ARM: socfpga: dts: Remove hard coded clock-frequency property
ARM: socfpga: dts: add eeprom and rtc on i2c0
ARM: socfpga: dts: convert to preprocessor includes
ARM: socfpga: dts: add rtc on i2c0 to socrates
ARM: socfpga: dts: add support for EBV SOCrates
ARM: socfpga: dts: add can0+1
ARM: socfpga: dts: add i2c busses
ARM: socfpga: dts: add remaining interrupts for pdma
ARM: socfpga: dts: fix pdma interrupt
Signed-off-by: Olof Johansson <olof@lixom.net>
Fabio Estevam [Tue, 13 May 2014 01:04:24 +0000 (22:04 -0300)]
ARM: dts: imx35-pdk: Fix memory region description
On imx35pdk there are two DRAM chip selects that are used:
CS0 at 0x80000000
CS1 at 0x90000000
Each bank is connected to 128MB of DRAM, giving a total of 256MB of system DRAM.
Fix the memory layout to describe the hardware appropriately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Sat, 10 May 2014 15:47:35 +0000 (12:47 -0300)]
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: Add CAN support
Add support for CAN based on a MCP2515 connected to ECSPI1.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Iain Paton [Fri, 9 May 2014 15:02:11 +0000 (16:02 +0100)]
ARM: dts: imx6: add new board RIoTboard
add element14s RIoTboard http://www.riotboard.org which is an i.MX6Solo
based design targeted at makers.
Signed-off-by: Iain Paton<ipaton0@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Iain Paton [Fri, 9 May 2014 15:01:56 +0000 (16:01 +0100)]
ARM: dts: imx6: i2c4 cleanup
add missing i2c4 clock and correct the compatible string to match other
imx6 i2c blocks
Signed-off-by: Iain Paton<ipaton0@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Thu, 17 Apr 2014 13:28:06 +0000 (15:28 +0200)]
ARM: dts: imx6: edmqmx6: add vcc and vio power supplies to stmpe
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Fri, 9 May 2014 06:11:19 +0000 (08:11 +0200)]
ARM: dts: Karo TX25: use hardware ecc
We should use hardware ecc on i.MX. While at it, add the optional
nand-bus-width property.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Fri, 9 May 2014 11:59:55 +0000 (19:59 +0800)]
ARM: dts: Karo TX25: Add phy reset gpio and supply for FEC
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Fri, 9 May 2014 06:11:17 +0000 (08:11 +0200)]
ARM: dts: Karo TX25: Add pinctrl nodes
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Fri, 9 May 2014 06:11:16 +0000 (08:11 +0200)]
ARM: dts: i.MX25: Add IRAM node
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Fri, 9 May 2014 06:11:14 +0000 (08:11 +0200)]
ARM: dts: i.MX25: Add mmc aliases
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Thu, 8 May 2014 06:17:30 +0000 (08:17 +0200)]
ARM: dts: i.MX51 babbage: Fix FEC pad ctrl settings
The dts relied on the FEC pad ctrl settings from the bootloader by
using the NO_PAD_CTRL option. This breaks once the bootloader starts
initializing the pad ctrl settings from the same dts file. Change
to real pad ctrl settings taken from the platform based babbage
support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Thu, 8 May 2014 14:10:56 +0000 (11:10 -0300)]
ARM: dts: imx6qdl-sabresd: Add USDHC4 support
USDHC4 is connected to a DDR MMC. Add support for it.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Russell King [Fri, 18 Apr 2014 10:01:27 +0000 (11:01 +0100)]
ARM: imx: add HDMI support for SolidRun HummingBoard and Cubox-i
Add the HDMI DT configuration for the SolidRun HummingBoard and Cubox-i.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Wed, 7 May 2014 18:09:05 +0000 (20:09 +0200)]
ARM: dts: imx6: edmqmx6: add SPI bus and flash
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Wed, 7 May 2014 18:09:04 +0000 (20:09 +0200)]
ARM: dts: imx6: edmqmx6: add pinctrl for pfuze irq gpio
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Tue, 6 May 2014 16:34:19 +0000 (13:34 -0300)]
ARM: dts: imx6q-udoo: Add HDMI support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Wed, 7 May 2014 13:19:00 +0000 (15:19 +0200)]
ARM: dts: Add stdout-path property to i.MX boards
This adds the stdout-path property to various i.MX boards. Values
of the property have been taken from barebox, so they should be
correct. Also, the older linux,stdout-path property is converted
to stdout-path.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tim Harvey [Thu, 1 May 2014 06:34:04 +0000 (23:34 -0700)]
ARM: dts: imx: Fix LVDS mapping for Ventana GW52xx
The GW52xx supports LVDS on channel 0. Remove the obsolete crtcs node and
add display timings for the HanStar HSD100PXN1 display.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
projects / GitHub / exynos8895 / android_kernel_samsung_universal8895.git / log