[media] au0828: make sure video standard is setup in tuner-core

If the user performs a tuning attempt without explicitly calling the
s_std ioctl(), a value of zero is sent from tuner-core to xc5000.  This
causes the xc5000 driver to leave the standard unchanged.  The problem
was masked by the fact that the xc5000 driver defaulted to NTSC, but if
you happened to perform an ATSC/ClearQAM tuning attempt and then do an
analog tune, the net effect is an analog tune with the standard still
set to DTV6.

Keep track of whether the standard has ever been sent to tuner-core.  We
don't make an s_std subdev call explicitly during probe because that
will cause a firmware load (which is very time consuming on the 950q).
With the logic in this patch, the s_std call will occur automatically on
the s_freq call if it hasn't already been set.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au0828: fix race condition that causes xc5000 to not bind for digital

In some cases users would see the xc5000_attach() call failing for the
digital side of the tuner on initialization.  This is because of udev
running v4l-id while the digital side of the board is still coming up.

This is the exact same race condition which was present in em28xx (not
surprising since I copied all the locking logic from that driver when I
added analog support).  Reproduce Mauro's fix from the em28xx driver in
au0828.

Reported-by: Rick Harding <rharding@mitechie.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc5000: properly report i2c write failures

The logic as written would *never* actually return an error condition,
since the loop would run until the counter hit zero but the check was
for a value less than zero.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc5000: add support for showing the SNR and gain in the debug output

When debugging is enabled, also show the analog SNR and the total gain
status values.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc5000: properly show quality register values

The quality register only has relevant data in bits 2-0, so discard the
other bits (which results in a value being printed that is consistent
with the expected 0-7 range).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au0828: Make the s_reg and g_reg advanced debug calls work against the bridge

The g_reg and s_reg calls worked properly if acting on subdev registers
(such as the au8522), but didn't work against the au0828 itself.  Copy
the logic over from em28xx.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au8522: properly recover from the au8522 delivering misaligned TS streams

There is an apparent bug in the au8522 TS clocking which can result in
it delivering a TS payload to the au0828 that is shifted by some number
of bits. For example, the device will announce a packet containing "FA
38 FF F8" which if you shift left one bit is "1F 47 1F FF F0..."

This presents itself as no TS stream being delivered from the kernel to
userland, since the kernel demux will drop every packet.

In the event that this condition occurs, restart the DVB stream.

Also, this patch includes a couple of lines of cleanup to not change the
FIFO configuration while the FIFO is running (which can screw up the
state machine), and dequeue the buffers before turning off the FIFO.
This puts the logic in sync with the Windows driver.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au8522: Fix off-by-one in SNR table for QAM256

The table of valid SNR values for QAM 256 is off by one, and as a result
if the SNR is oscillating between 40.0 and 39.9 dB, tools like azap show
it going back and forth between 40.0 and 0 (misleading some people,
including myself, to think signal lock is being lost or there is a
problem with register reads).

Fix the table so that 40.0 dB is properly represented.

Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au8522: fix intermittent lockup of analog video decoder

It turns up the autodetection for the video standard in the au8522 is
prone to hanging the chip until a reset is performed.  This condition is
trivial to reproduce simply by tuning to a station and then rapidly
unplugging/ replugging the coax feed.

Because we've never claimed to support anything other than NTSC-M, just
disable the video-standard autodetection logic and force it to always be
NTSC-M.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-dev: remove V4L2_FL_LOCK_ALL_FOPS

All drivers that needed V4L2_FL_LOCK_ALL_FOPS have been converted,
so remove this flag altogether.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mem2mem_testdev: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vpif_capture: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vpif_display: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-tv: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-g2d: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-jpeg: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] soc_camera: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx231xx: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bfin_capture: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sh_vou: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mx2_emmaprp: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vpbe_display: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s2255drv: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fsl-viu: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] wl128x: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dt3155v4l: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tm6000: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] usbvision: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cpia2: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

I also removed some dead code in the form of the saa7146_devices list and
saa7146_devices_lock mutex: these were used once but that was a long time
ago.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: remove V4L2_FL_LOCK_ALL_FOPS

Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] az6007: Update copyright

Update copyright comments after dvb-usb-v2 conversion.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] az6007: handle CI during suspend/resume

The dvb-usb-v2 core doesn't know anything about CI. So, the
driver needs to handle it by hand. This patch stops CI just
before stopping URB's/RC, and restarts it before URB/RC start.

It should be noticed that suspend/resume is not yet working properly,
as the PM model requires the implementation of reset_resume:
dvb_usb_az6007 1-6:1.0: no reset_resume for driver dvb_usb_az6007?
But this is not implemented there at dvb-usb-v2 yet.

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] az6007: make all functions static

There's no reason why those functions shouldn't be static.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] az6007: rename "st" to "state" at az6007_power_ctrl()

On all other parts, this var is called state. So, use the same
name here, to be consistent.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] az6007: Fix the number of parameters for QAM setup

Remove those warning messages:
[  121.696758] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[  121.703401] drxk: 02 00 00 00 10 00 07 00 03 02                    ..........
[  121.703587] drxk: Warning -22 on QAMDemodulatorCommand

Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] az6007: fix the I2C W+R logic

The test for I2C W+R will never be true. Fix it.

Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] az6007: convert it to use dvb-usb-v2

Change it to use dvb-usb-v2. The driver should be working as before.
The only functional changes should be at the driver debug logs.

This driver needs the cypress firmware load, so, auto-selects it.

Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb-usb-v2: Don't ask user to select Cypress firmware module

The dvb-usb-v2 cypress firmware module is not optional, as drivers
won't work without it. So, instead of opening a menu for the user to
manually select, let the drivers that need it to select, hiding this
option from the Kconfig menu.

Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb-usb-v2: Fix cypress firmware compilation

ERROR: "usbv2_cypress_load_firmware" [drivers/media/dvb/dvb-usb-v2/dvb-usb-az6007.ko] undefined!

Cypress fimware will never be compiled properly, as the Makefile rule
is wrong.

Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i.MX27: Fix mx2_emmaprp mem2mem driver clocks

This driver wasn't converted to the new clock framework
(e038ed50a4a767add205094c035b6943e7b30140).

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] i.MX27: Visstrim_M10: Add support for deinterlacing driver

Visstrim_M10 have a tvp5150 whose video output must be deinterlaced.
The new mem2mem deinterlacing driver is very useful for that purpose.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m2m-deinterlace: fix two warnings

drivers/media/video/m2m-deinterlace.c: In function ‘deinterlace_issue_dma’:
drivers/media/video/m2m-deinterlace.c:363:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’ [-Wformat]
drivers/media/video/m2m-deinterlace.c:363:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 5 has type ‘dma_addr_t’ [-Wformat]

Cc: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: Add mem2mem deinterlacing driver

Some video decoders such as tvp5150 provide separate
video fields (V4L2_FIELD_SEQ_TB/BT). This driver uses
dmaengine to convert this format to V4L2_FIELD_INTERLACED_TB/BT
(weaving) or V4L2_FIELD_NONE (line doubling) so that the
image can be displayed or processed.

Of course there will be combing effect in the image but this
can be accepted for some low quality applications.

Currently only YUV420 and YUYV formats are supported but
it can be extended later.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Visstrim M10: Add support for Coda

Support the codadx6 that is included in
the i.MX27 SoC.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: coda: Add driver for Coda video codec

Coda is a range of video codecs from Chips&Media that
support H.264, H.263, MPEG4 and other video standards.

Currently only support for the codadx6 included in the
i.MX27 SoC is added. H.264 and MPEG4 video encoding
are the only supported capabilities by now.

[mchehab@redhat.com: Add missing include linux/of.h]
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Reviewed-by: Philipp Zabel<p.zabel@pengutronix.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] i.MX: coda: Add platform support for coda in i.MX27

i.MX27 SoC include a codadx6 codec that is able to encode
and decode H.264, H.263 and MPEG4.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] move dvb-usb-ids.h to dvb-core

While this header were meant to be used just by dvb-usb driver, it
is now being used also by dvb-usb-v2 and cx231xx. So, move it to a
better place.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usbv2: rename dvb_usb_firmware to cypress_firmware

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9015: remote controller fixes

1)
AF9015 remote controller query will fail rarely due to register
access failures and dvb_usb_v2 will stop rc polling when error
returned. Add logic to allow errors until two consecutive errors
occurs.

2)
Remote controller key map was not loaded in case of key map was set as
a device property. Fix it.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: move from dvb-usb to dvb-usb-v2

Move to own directory.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gl861: convert to new DVB USB

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxl111sf: convert to new DVB USB

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: register device even no remote keymap defined

It failed to register device when remote keymap was not set.
Fix it to register device even keymap is NULL. In that case
just skip remote registration.

Driver should set RC_MAP_EMPTY to enable remote in case of
there is remote receiver but default keymap is unknown.

Reported-by: pierigno <pierigno@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: remove usb_clear_halt() from stream

It works no longer as it was designed since we can change streaming
configuration during device operation.

Maybe it should be performed conditionally on cases when streaming
endpoint is changed. Anyhow, let it out now and add later if needed.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: do not try to remove non-existent adapter

Check that adapter exists before trying to remove it.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: use dev_* logging macros

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: change streaming control callback parameter

Pass frontend instead of adapter as some drivers need to make
decisions based frontend.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: fix power_ctrl() callback error handling

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: update copyrights

Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: remove unused variable

It was left from the legacy remote controller we do not support.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: update header dvb_usb.h comments

Comment briefly all used structures and variables.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: refactor dvb_usbv2_generic_rw()

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: multiple small tweaks around the code

Naming, small code changes, debug writings, etc.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: move dvb_usbv2_generic_rw() debugs behind define

It is nice to have this debug, but as it generates very huge amount
of traffic, better to make it conditional. Use define macro to disable
it as I did not find out how to use dynamic debugs to dump variable
length buffers like that.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: merge files dvb_usb_init.c and dvb_usb_dvb.c

Merge files dvb_usb_init.c and dvb_usb_dvb.c to dvb_usb_core.c.
It is still under 1000 lines of code after all the optimization
so put it one file.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: refactor dvb_usb_ctrl_feed() logic

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: remove num_adapters_initialized variable

We can live easily without it so remove it, make code and binary
few bytes smaller.

>From struct dvb_usb_device variable int num_adapters_initialized.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: use identify_state() to resolve firmware name

Merge get_firmware_name() to identify_state().

It is wise to resolve firmware name in that routine as it does
decision wether or not to load firmware at all. It is one very
rarely needed callback less.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: merge get_ts_config() to get_usb_stream_config()

Piggypag TS type callback to USB stream callback and change
callback name slightly to fit better.
Both of those are rather rare callback and has a relation. Transport
Stream, TS, is input stream and USB stream is output stream of
DVB USB bridge.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: use container_of() for adapter to device

We dont need that pointer as we can use container_of() macro thus
remove it.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ec168: use DVB UDB macros

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ce6230: use DVB USB macros

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au6610: use DVB USB macros

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: use DVB USB macros

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: git rid of dvb_usb_adapter state variable

We can live without it easily.

Also USB data stream complete callback checks for feedcount
seems to be quite redundant so remove those also.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: convert to new DVB USB

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: use lock to sync feed and frontend control

There was synchronization problem when streaming was stopped.
Frontend was ran down before stream which causes problems.
Use mutex to synchronization. Now it looks like that:
LOCK
start frontend
UNLOCK
LOCK
start streaming
[...]
stop streaming
UNLOCK
LOCK
stop frontend
UNLOCK

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9015: use helper macros for some pointers

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: helper macros for device/adapter/frontend pointers

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9015: update USB streaming configuration logic

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: change USB stream config logic

Initial / default USB stream configuration is now set always as a
dvb_usb_device_properties. Dynamic configuration is done top of
that if callback .get_usb_stream_config() exists. Default values
are set when callback is called so callback needs only change
values that are different than default.

In addition of that define two macros DVB_USB_STREAM_BULK() and
DVB_USB_STREAM_ISOC() for filling struct usb_data_stream_properties

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: add macros to fill USB stream properties

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: .read_mac_address() callback changes

Give DVB adapter as a parameter for callback. MAC address is
adapter property and it could be (at least in theory) there
is devices having multiple adapters and all has own MAC.

Also add error handling. If callback fails error is returned
which leads device unregister.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: remove num_frontends_initialized from dvb_usb_adapter

We can live easily without that variable.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: move fe_ioctl_override() callback

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: get rid of dvb_usb_device state

Remove state from struct dvb_usb_device as we can live without.
Add some debug logs.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: simplify remote init/exit logic

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: try to remove all adapters on exit

It did not removed adapter on error case as .num_adapters_initialized
was set after success adapter initialization. It should be safe to
try remove all possible adapters in any-case.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: do not release USB interface when device reconnects

USB core will call disconnect and remove driver for us as device
will disconnect itself. After that it is loaded again as a new
device but it is warm and no firmware loading needed.

Reported-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: return the download ret in dvb_usb_download_firmware

The first being this patch, no return value from dvb_usb_download_firmware
causes system wide dead lock with COLD disconnect as system attempts to continue
to warm state.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: convert to new DVB USB

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: attach tuners later

It is more than nice to have all those frontend pointers when
attaching tuner to the frontend in question. Make that possible
attaching tuners after dvb_register_frontend()

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ce6230: various small changes

Small changes like log writings. No functionality changes.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ce6230: convert to new DVB USB

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb_usb_v2: move remote controller to the main file

It is only three functions so move it to the main.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au6610: convert to new DVB USB

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ec168: re-implement firmware loading

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>