git.stricted.de - GitHub/moto-9609/android_kernel_motorola

iio: buffer-dma: Use ARRAY_SIZE in for loop range

Use the ARRAY_SIZE macro in the for loops that access queue->fileio.blocks.
Macro is already used in a couple of places where this access occurs,
but range was hardcoded in these locations.

Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: max1363: Fix missing i2c_device_id for MAX1164x parts

The driver supports MAX11644, MAX11645, MAX11646 and MAX11647 parts. But
the corresponding i2c_device_id are missing. Add them!

Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: proximity: as3935: remove redundant zeroing of tune_cap

This is redundant as the containing stucture is allocated as part of
iio_device_alloc using kzalloc and hence is already 0.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: stx104: Add GPIO support for the Apex Embedded Systems STX104

The Apex Embedded Systems STX104 device features eight lines of digital
I/O (four digital inputs and four digital outputs). This patch adds GPIO
support for these eight lines of digital I/O via GPIOLIB.

Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: as3935: improve error reporting in as3935_event_work

gcc warns about a potentially uninitialized variable use
in as3935_event_work:

drivers/iio/proximity/as3935.c: In function ‘as3935_event_work’:
drivers/iio/proximity/as3935.c:231:6: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]

This case specifically happens when spi_w8r8() fails with a
negative return code. We check all other users of this function
except this one.

As the error is rather unlikely to happen after the device
has already been initialized, this just adds a dev_warn().
Another warning already exists in the same function, but is
missing a trailing '\n' character, so I'm fixing that too.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging: iio: accel: add error check

Go to error_ret if sca3000_read_ctrl_reg() failed.

Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ti-adc081c: add ACPI device ID matching

Add ACPI device ID matching for TI ADC081C/ADC101C/ADC121C ADCs.

Signed-off-by: Dan O'Donovan <dan@emutex.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Refuse to register triggers with duplicate names

The trigger name is documented as unique but drivers are currently
allowed to register triggers with duplicate names. This should be
considered a bug since it makes the 'current_trigger' interface
unusable.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: generic_buffer: Fix --trigger-num option

Initialize trig_num to -1 and handle trig_num=0 as a valid id.

Fixes: 7c7e9dad (iio: iio_generic_buffer: Add --trigger-num option)
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

mailmap: update Matt Ranostay email address

Set current email address to replace previous employers email addresses.

Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

mailmap: update Adriana Reus email address

Set current email address instead of previous employers email address.

Signed-off-by: Adriana Reus <adi.reus@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: ms5637 Add Measurement Specialties explicit MS5805 and MS5837 support

Signed-off-by: William Markezana <william.markezana@meas-spec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mma8452: update Freescale company information

NXP took over Freescale, so add NXP to the driver descriptions

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mma8452: update device description in header comments

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mma8452: update contact information for Martin Kepplinger

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light: gp2ap020a00f: use iio helper function to lock direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. Includes a
tiny bit of refactoring (single case -> if) and simplified return
flow.

Also prevents a theoretical race condition by effectively taking the lock
a little earlier than before.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light: isl29125: use iio helper function to guarantee direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. This allows
removal of an unused lock in the device private global data.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light: tcs3472: use iio helper function to guarantee direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. This allows
removal of an unused lock in the device private global data.

Also prevents a previous race condition when a buffer is enabled whilst
a raw read is going on.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light: tcs3414: use iio helper function to guarantee direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same. This allows
removal of an unused lock in the device private global data.

Also prevents a possible race around a buffer being enabled whilst
a read is going on.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: proximity: lidar: switch to iio_device_claim_*_mode helpers

Switch from using indio_dev->mlock to the iio_device_claim_*_mode
helper functions.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:trigger: Experimental kthread tight loop trigger (thread only)

This patch is in response to that of
Gregor Boirie <gregor.boirie@parrot.com>
who proposed using a tight kthread within a device driver (be it with the
support factored out into a helper library) in order to basically spin as
fast as possible.

It is meant as a talking point rather than a formal proposal of the code
(though we are heading towards that I think).
Also gives people some working code to mess around with.

I proposed that this could be done with a trigger with a few constraints
and this is the proof (be it ugly) of that.

There are some constraints though, some of which we would want to relax
if this were to move forward.

* Will only run the thread part of the registered pollfunc.  This is to
  avoid the overhead of jumping in and out of interrupt context.  Is the
  overhead significant?  Not certain but feels like it should be!

* This limitation precludes any device that 'must' do some work in
  interrupt context.  However, that is true of few if any drivers and
  I suspect that any that do will be restricted to using triggers they
  provide themselves.  Usually we have a top half mainly to grab a
  timestamp as soon after the dataready type signal as possible.

Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>

iio: adc: ti_am335x_adc: use SIMPLE_DEV_PM_OPS helper macro

Replace ifdefs with SIMPLE_DEV_PM_OPS helper macro.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ti_am335x_adc: use variable names for sizeof() operator

Fix the code formatting to use the kernel preferred style
of using the actual variables to determize the size using
the sizeof() operator.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad7791: claim direct mode when writing frequency

Driver was checking for direct mode and trying to lock it, but
left a gap where mode could change before the desired operation.
Use iio_device_claim_direct_mode() to guarantee device stays in
direct mode.

Refactor function to clarify look-up followed by lock sequence.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad7793: claim direct mode when writing frequency

Driver was checking for direct mode and trying to lock it, but
left a gap where mode could change before the desired operation.
Use iio_device_claim_direct_mode() to guarantee device stays in
direct mode.

Refactor function to clarify look-up followed by lock sequence.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: iio_generic_buffer: Add --trigger-num option

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: iio_generic_buffer: Add --device-num option

This makes it possible to distinguish between iio devices with the same
name.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: iio_generic_buffer: Cleanup when receiving signals

This will clean (disable buffer/trigger/channels) when doing
something like a CTRL-C. Otherwise restarting generic_buffer requires a
manual echo 0 > buffer/enable

This also cleanup up all the code freeing string buffers at
the end of main. We initialize all pointers to NULL so that cleanup can
all be done under a single error label.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: proximity: as3935: remove redundant MODULE_ALIAS

MODULE_ALIAS isn't needed since the module name is the same as the alias
defined.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: magnetometer: bmc150: Document Bosch supported chips

bmc150 driver supports also BMC156 and BMM150 chips.

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: chemical: atlas-ph-sensor: add EC feature

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: electricalconductivity: add IIO_ELECTRICALCONDUCTIVITY type

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: chemical: atlas-ph-sensor: reorg driver to allow multiple chips

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

tools: iio: Rename generic_buffer to iio_generic_buffer

This makes it clear that generic_buffer is an IIO tool
and also complies with filename conventions in tools/iio.

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

tools: iio: Add ability to install/uninstall

Add options to the Makefile for install/uninstall similar to other tools.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad799x: use iio helper function to guarantee direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad7923: use iio helper function to guarantee direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad7887: use iio helper function to guarantee direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad7476: use iio helper function to guarantee direct mode

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad7266: claim direct mode during sensor read

Driver was checking for direct mode but not locking it down.
Use iio_device_claim_direct_mode() to guarantee device stays
in direct mode.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:st_sensors: fix power regulator usage

Ensure failure to enable power regulators is properly handled.

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:st_sensors: emulate SMBus block read if needed

Use SMBus "block read" protocol only when supported by adapter.

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:st_sensors: unexport st_sensors_get_buffer_element

Remove st_sensors_get_buffer_element symbol export since not explicitly
used outside of st_sensors driver.

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:st_pressure:initial lps22hb sensor support

Initial support for ST LPS22HB pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hb.pdf

Features:
* pressure data and timestamping channels
* sampling frequency selection
* interrupt based trigger
* over I2C or SPI

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: triggers: Make trigger ops structure explicitly non optional.

This structure has not been optional for a long time (if ever) but the
code implies that it is. As we then use it later in a fashion that would
crash if it was in fact NULL, it's inconsistent so fix it up by removing
unnecessary checks.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ti-ads1015: add datasheet names

Add datasheet names for ADC channels to allow iio consumers access.

Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

MAINTAINERS: Add file patterns for staging iio device tree bindings

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

MAINTAINERS: Add file patterns for iio device tree bindings

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: pressure: bmp280: add humidity support

Enable humidity support for the BME280 part

Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light: jsa1212: remove unneeded i2c check functionality test

This driver does not call i2c_smbus_read|write_byte_data(),
so remove the corresponding functionality test. It uses regmap
to handle byte transfers transparently.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by:Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: nau7802: Expose possible gains in sysfs

The Nuvoton NAU7802 ADC is able to adjust its gain but prior knowledge of
its possible values was required to adjust it. Users had to guess the
possible gain values based on the ADC datasheet or on this driver's code.

This exposes the possible values in the in_voltage_scale_available file of
each nau7802 ADC device. The gain is set for the whole ADC and is therefore
not configurable by channel. Thus, there exists only one
in_voltage_scale_available file for each nau7802 ADC device even if it has
two separate channels.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: max5487: Add support for Maxim digital potentiometers

Add implementation for Maxim MAX5487, MAX5488, MAX5489
digital potentiometers.

Datasheet:
http://datasheets.maximintegrated.com/en/ds/MAX5487-MAX5489.pdf

Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
CC: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Export I2C module alias information

The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.

The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: Add triggered buffer support for BMA220

Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ti-ads1015: add support for ADS1115 part

TI ADS1115 is a 16-bit resolution ADC that is register map
compatible with the ADS1015 device.

Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: magn: Add support for BMM150 magnetometer

BMM150 is register compatible with magnetometer part of
BMC156.

Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: Add support for Bosch BMA220

This commit adds basic support for the Bosch Sensortec BMA220
digital triaxial acceleration sensor.
The device datasheet can be found here:

http://www.mouser.com/pdfdocs/BSTBMA220DS00308.PDF

Includes:
- raw readings
- ACPI detection
- power management

Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: potentiometer: tpl0102: remove unneeded i2c check functionality test

Actually I2C_FUNC_SMBUS_WORD_DATA isn't need for this device, and regmap
handles all single byte reads transparently.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mma8452: add support for oversampling ratio

This adds the following sysfs files according to the iio ABI:

-rw-r--r-- 4096 in_accel_oversampling_ratio
-r--r--r-- 4096 in_accel_oversampling_ratio_available

Internally, the device knows about 4 different power modes that differ
in oversampling ratio (and power consumption). We just show the user
what oversampling ratio(s) is/are available, depending on the current
frequency.

The referenced table in the datasheets makes it easier to understand.

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Documentation: iio: Add IIO software devices docs

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: dummy: Convert IIO dummy to configfs

We register a new device type named "dummy", this will create a
configfs entry under:
* /config/iio/devices/dummy.

Creating dummy devices is now as simple as:

$ mkdir /config/iio/devices/dummy/my_dummy_device

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Add support for creating IIO devices via configfs

This is similar with support for creating triggers via configfs.
Devices will be hosted under:
* /config/iio/devices

We allow users to register "device types" under:
* /config/iio/devices/<device_types>/

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe4404: ENSEPGAIN is part of CONTROL2 register

Rename this definition, no functional changes.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Remove unused definitions

These definitions are not currently used and if the functionality
they represent is needed the values should be added back to a table
for easy userspace use.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Match LED currents to stages

The current channel number for the LEDs should match the stage
number that they are active during, fix this here.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Make gain settings a modifier for the stages

Currently the TIA gain settings are exported to userspace as sysfs
entries that do not clearly represent their internal relation to the
sampling stages. The gain settings are enabled on a per-stage basis,
this can be seen in figure 24 of the current AFE4404 datasheet.
These gain settings should therefore be tied to the channels that are
read during these stages. Make this change here.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Use regmap fields

These drivers can use regmap fields to access fields in registers, this
allows us to remove some macros/defines and simplify code, do this here.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Remove channel names

These AFEs have 4 ADC mesuring stages (called LED2, ALED2, LED1, and
ALED1 in the datasheet), we map these as channels, these stages can serve
different purposes depending on the application. For instance the AFE4404
has an additional LED (LED3), this LED can be timed to be active during
stage 2 (or anystage, but the datasheet describes this case and the name
of the stage reflects this use). This ability is used further in upcoming
parts that tie the front-end gain and the LED timings together. For these
reasons we remove explicit naming the channels.

Without channel names it is best that the index numbers are in order to
match the stage number, reorder the channel numbers.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe4404: Remove LED3 input channel

Input channel LED3 is only an alias for stage ALED2, this virtual channel
does nothing for us, remove this channel.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Remove unneeded offset handling

No channel in the afe4403 driver has IIO_CHAN_INFO_OFFSET set so
remove the handlers for this.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Fix scan_index assignment

The LED channels are not scannable and so scan_index should
be negative, fix this here.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Always use separate gain values

Locking the two gain stages to the same setting adds no value for us,
so initialize them as unlocked and remove the sysfs for unlocking them.
This also allows us to greatly simplify showing and setting the gain
registers.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Remove unneeded initializers

The drivers set some register values during initialization that can be
set at runtime, these defaults were used in testing but are not
necessary, remove these.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Remove of_match_ptr and ifdefs

The drivers DT tables are not built-in when OF is not enabled, this does
not save us enough to justify ugly ifdefs. Clean this up.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: health/afe440x: Fix kernel-doc format

Fix kernel-doc formatting for structs, and while we are making little
fixes, clarify the module description and update the copywrite.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

imu: bmi160: Add avail frequency and scale attributes

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mxs-lradc: disable only masked channels in mxs_lradc_hw_stop

Disabling of the touchscreen IRQs should be done in
mxs_lradc_disable_ts. So disable only the masked virtual channels
in mxs_lradc_hw_stop and finally remove the unused function
mxs_lradc_irq_en_mask.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mxs-lradc: remove mxs_lradc_ts_unregister

After using devm_input_allocate_device for registration
the function mxs_lradc_ts_unregister isn't necessary anymore
since mxs_lradc_ts_close already does the job.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mxs-lradc: simplify TS registration

This patch simplifies the TS registration of mxs-lradc by
using devm_input_allocate_device.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: Add support for Freescale MMA7660FC

Minimal implementation of an IIO driver for the Freescale
MMA7660FC 3-axis accelerometer. Datasheet:
http://www.nxp.com/files/sensors/doc/data_sheet/MMA7660FC.pdf

Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management

Signed-off-by: Constantin Musca <constantin.musca@intel.com>
Reviewed-by: Martin Klepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: ak8975: Support adapters limited to BYTE_DATA

The device has simple 8-bit registers but the driver incorrectly uses
block or word reads without checking functionality bits.

Fix by using i2c_smbus_read_i2c_block_data_or_emulated instead of
i2c_smbus_read_i2c_block_data or i2c_smbus_read_word_data. This will
check functionality bits and use the fastest available transfer method.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: inv_mpu6050: Add explicit support for MPU9150

This device is a package containing a MPU6050-like sensor and an AK8975
magnetometer. The magnetometer component is supported by the existing
ak8975 driver.

This patch also rephrases the Kconfig descriptions.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: inv_mpu6050: Add spi_device_id for INV_MPU6500

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: inv_mpu6050: Check WHO_AM_I register on probe

This can be used to distinguish mpu6500. This is a warning rather than
an error because the differences are mostly irrelevant and it's nice to
avoid breaking users with slightly incorrect ACPI/DT.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: inv_mpu6050: Remove inv_mpu6050_hw.num_reg

This field was unused and incorrect for mpu6500.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: inv_mpu6050: Cleanup hw_info mapping

The hw_info array was indexed by enum inv_devices chip_type despite the
fact that the enumeration had more members than the array and was
ordered differently.

The patch cleans this up and adds explicit chip_types to i2c/spi/acpi
IDs. It also adds some stricter checks inside the driver core.

This happened to work so far because the differences between the
supported models are very minor.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: pressure: bmp280: add ability to control oversampling rate

This adds ability to control the oversampling ratio of the temperature
and pressure measurement for both bmp180 and bmp280.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: pressure: bmp280: add support for BMP180

This adds support for the BMP180 to the bmp280 iio driver.

The BMP180 has already been supported by misc/bmp085 driver but it
doesn't use iio framework. This change adds the kconfig dependency
not to be selected both of them in order to avoid any issues.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

max44000: Initial triggered buffer support

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

max44000: Expose ambient sensor scaling

This patch exposes ALSTIM as illuminance_integration_time and ALSPGA as
illuminance_scale.

Changing ALSTIM also changes the number of bits available in the data
register. This is handled inside raw value reading because:
* It's very easy to shift a few bits
* It allows SCALE and INT_TIME to be completely independent controls
* Buffer support requires constant scan_type.realbits per-channel

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

max44000: Support controlling LED current output

This is exposed as an output channel with "led" as an extend_name.

Other sensors also have support for controlling an external LED. It's
not clear that simply exposing an undecorated output channel is the
correct approach.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

max44000: Initial support for proximity reading

The proximity sensor relies on sending pulses to an external IR led and
it is disabled by default on powerup. The driver will enable it with a
default power setting.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

max44000: Initial support

This just adds support for reporting illuminance with default settings.

Important default registers are written on probe because the device
otherwise lacks a reset function.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: humidity: Add triggered buffer support for AM2315

Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: humidity: Add support for AM2315

Add basic support for the Aosong AM2315 relative humidity
and ambient temperature sensor.
Includes support for raw readings and ACPI detection.

Datasheet:
http://www.aosong.com/asp_bin/Products/en/AM2315.pdf

Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: pressure: hp03: Add Hope RF HP03 sensor support

Add support for HopeRF pressure and temperature sensor.

This device uses two fixed I2C addresses, one for storing
calibration coefficients and another for accessing the ADC.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matt Ranostay <mranostay@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: st_gyro: Add lsm9ds0-gyro support

This device has an identical interface to other supported sensors and the patch
only adds IDs.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light: apds9960: silence uninitialized variable warning

It causes a static checker warning if we use "buf" on the failure path
so move that inside the if statement.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:imu:mpu6050: enhance mounting matrix support

Add a new rotation matrix sysfs attribute compliant with IIO core
mounting matrix API.
Matrix is retrieved from "in_anglvel_mount_matrix" and
"in_accel_mount_matrix" sysfs attributes. It is declared into mpu6050 DTS
entry as a "mount-matrix" property.

Old interface is kept for backward userspace compatibility and may be
retrieved from legacy platform_data mechanism only.

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>