arm64: dts: marvell: armada-37xx: Set pcie_reset_pin to gpio function

commit 715878016984b2617f6c1f177c50039e12e7bd5b upstream.

We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.

We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.

Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.

So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.

We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Remi Pommarel <repk@triplefau.lt>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: marvell: armada-37xx: declare PCIe reset pin

commit a5470af981a0cc14a650af8da5186668971a4fc8 upstream.

One pin can be muxed as PCIe endpoint card reset.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: armada-37xx: Correct PWM pins definitions

commit baf8d6899b1e8906dc076ef26cc633e96a8bb0c3 upstream.

The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).

The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"

This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".

Change the "pwmN" groups to support "led" function.

Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.

Fixes: b835d6953009 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: armada-37xx: add missing pin: PCIe1 Wakeup

commit 4d98fbaacd79a82f408febb66a9c42fe42361b16 upstream.

Declare the PCIe1 Wakeup which was initially missing.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: armada-37xx: Correct mpp definitions

commit 823868fceae3bac07cf5eccb128d6916e7a5ae9d upstream.

This is a cleanup and fix of the patch by Ken Ma <make@marvell.com>.

Fix the mpp definitions according to newest revision of the
specification:
  - northbridge:
    fix pmic1 gpio number to 7
    fix pmic0 gpio number to 6
  - southbridge
    split pcie1 group bit mask to BIT(5) and  BIT(9)
    fix ptp group bit mask to BIT(11) | BIT(12) | BIT(13)
    add smi group with bit mask BIT(4)

[gregory: split the pcie group in 2, as at hardware level they can be
configured separately]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix checking for link up via LTSSM state

commit 661c399a651c11aaf83c45cbfe0b4a1fb7bc3179 upstream.

Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.

Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.

To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.

Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.

Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix link training

commit f76b36d40beee0a13aa8f6aa011df0d7cbbb8a7f upstream.

Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbffac ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.

After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.

(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
 and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
 also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
 PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)

Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.

Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.

Commit 43fc679ced18 ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].

These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582f5 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.

Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.

The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.

According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851daa ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.

Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.

On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.

Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.

The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).

It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)

It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.

[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/

Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Add PCI_EXP_LNKCTL2_TLS* macros

commit c80851f6ce63a6e313f8c7b4b6eb82c67aa4497b upstream.

The Link Control 2 register is missing macros for Target Link Speeds.  Add
those in.

Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: use "GT" instead of "GB"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix PCIe Max Payload Size setting

commit a4e17d65dafdd3513042d8f00404c9b6068a825c upstream.

Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.

Without this kernel prints suspicious line:

    pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)

With this change it changes to:

    pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)

Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Configure PCIe resources from 'ranges' DT property

commit 64f160e19e9264a7f6d89c516baae1473b6f8359 upstream.

In commit 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.

But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.

Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.

This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a55, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.

This patch fixes kernel crash when trying to access PCIe IO space.

Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Remove PCIe outbound window configuration

commit 6df6ba974a55678a2c7d9a0c06eb15cde0c4b184 upstream.

Outbound window is used to translate CPU space addresses to PCIe space
addresses when the CPU initiates PCIe transactions.

According to the suggestion of the HW designers, the recommended
solution is to use the default outbound parameters, even though the
current outbound window setting does not cause any known functional
issue.

This patch doesn't address any known functional issue, but aligns to
HW design guidelines, and removes code that isn't needed.

Signed-off-by: Evan Wang <xswang@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: handled host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Update comment about disabling link training

commit 1d1cd163d0de22a4041a6f1aeabcf78f80076539 upstream.

According to PCI Express Base Specifications (rev 4.0, 6.6.1
"Conventional reset"), after fundamental reset a 100ms delay is needed
prior to enabling link training.

Update comment in code to reflect this requirement.

Link: https://lore.kernel.org/r/20201202184659.3795-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Move PCIe reset card code to advk_pcie_train_link()

commit d0c6a3475b033960e85ae2bf176b14cab0a627d2 upstream.

Move code which belongs to link training (delays and resets) into
advk_pcie_train_link() function, so everything related to link training,
including timings is at one place.

After experiments it can be observed that link training in aardvark
hardware is very sensitive to timings and delays, so it is a good idea to
have this code at the same place as link training calls.

This patch does not change behavior of aardvark initialization.

Link: https://lore.kernel.org/r/20200907111038.5811-6-pali@kernel.org
Tested-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix compilation on s390

commit b32c012e4b98f0126aa327be2d1f409963057643 upstream.

Include linux/gpio/consumer.h instead of linux/gpio.h, as is said in the
latter file.

This was reported by kernel test bot when compiling for s390.

  drivers/pci/controller/pci-aardvark.c:350:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror,-Wimplicit-function-declaration]
  drivers/pci/controller/pci-aardvark.c:1074:21: error: implicit declaration of function 'devm_gpiod_get_from_of_node' [-Werror,-Wimplicit-function-declaration]
  drivers/pci/controller/pci-aardvark.c:1076:14: error: use of undeclared identifier 'GPIOD_OUT_LOW'

Link: https://lore.kernel.org/r/202006211118.LxtENQfl%25lkp@intel.com
Link: https://lore.kernel.org/r/20200907111038.5811-2-pali@kernel.org
Fixes: 5169a9851daa ("PCI: aardvark: Issue PERST via GPIO")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Don't touch PCIe registers if no card connected

commit 70e380250c3621c55ff218cbaf2272830d9dbb1d upstream.

When there is no PCIe card connected and advk_pcie_rd_conf() or
advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
root bridge, the aardvark driver throws the following error message:

  advk-pcie d0070000.pcie: config read/write timed out

Obviously accessing PCIe registers of disconnected card is not possible.

Extend check in advk_pcie_valid_device() function for validating
availability of PCIe bus. If PCIe link is down, then the device is marked
as Not Found and the driver does not try to access these registers.

This is just an optimization to prevent accessing PCIe registers when card
is disconnected. Trying to access PCIe registers of disconnected card does
not cause any crash, kernel just needs to wait for a timeout. So if card
disappear immediately after checking for PCIe link (before accessing PCIe
registers), it does not cause any problems.

Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Introduce an advk_pcie_valid_device() helper

commit 248d4e59616c632f37f04c233eec6d5008384926 upstream.

In other to mimic other PCIe host controller drivers, introduce an
advk_pcie_valid_device() helper, used in the configuration read/write
functions.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Indicate error in 'val' when config read fails

commit b1bd5714472cc72e14409f5659b154c765a76c65 upstream.

Most callers of config read do not check for return value. But most of the
ones that do, checks for error indication in 'val' variable.

This patch updates error handling in advk_pcie_rd_conf() function. If PIO
transfer fails then 'val' variable is set to 0xffffffff which indicates
failture.

Link: https://lore.kernel.org/r/20200528162604.GA323482@bjorn-Precision-5520
Link: https://lore.kernel.org/r/20200601130315.18895-1-pali@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Replace custom macros by standard linux/pci_regs.h macros

commit 96be36dbffacea0aa9e6ec4839583e79faa141a1 upstream.

PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.

Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Issue PERST via GPIO

commit 5169a9851daaa2782a7bd2bb83d5b1bd224b2879 upstream.

Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).

Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.

If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.

It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.

Tested on Turris MOX.

Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Improve link training

commit 43fc679ced18006b12d918d7a8a4af392b7fbfe7 upstream.

Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.

Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.

To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.

Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Train link immediately after enabling training

commit 6964494582f56a3882c2c53b0edbfe99eb32b2e1 upstream.

Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).

Move the code which enables link training immediately before the one
which starts link traning.

This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.

Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Wait for endpoint to be ready before training link

commit f4c7d053d7f77cd5c1a1ba7c7ce085ddba13d1d7 upstream.

When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).

Because the pin configuration comes from the "default" pinctrl it is
implicitly configured before the probe callback is called:

driver_probe_device()
  really_probe()
    ...
    pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
                           function and PERST# is asserted */
    ...
    drv->probe()

[1] "PCI Express Base Specification", REV. 4.0
    PCI Express, February 19 2014, 6.6.1 Conventional Reset

Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix a leaked reference by adding missing of_node_put()

commit 3842f5166bf1ef286fe7a39f262b5c9581308366 upstream.

The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

irq_domain_add_linear() also calls of_node_get() to increase refcount,
so irq_domain will not be affected when it is released.

Detected by coccinelle with the following warnings:
  ./drivers/pci/controller/pci-aardvark.c:826:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 798, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix I/O space page leak

commit 1df3e5b3feebf29a3ecfa0c0f06f79544ca573e4 upstream.

When testing the R-Car PCIe driver on the Condor board, if the PCIe PHY
driver was left disabled, the kernel crashed with this BUG:

  kernel BUG at lib/ioremap.c:72!
  Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
  Modules linked in:
  CPU: 0 PID: 39 Comm: kworker/0:1 Not tainted 4.17.0-dirty #1092
  Hardware name: Renesas Condor board based on r8a77980 (DT)
  Workqueue: events deferred_probe_work_func
  pstate: 80000005 (Nzcv daif -PAN -UAO)
  pc : ioremap_page_range+0x370/0x3c8
  lr : ioremap_page_range+0x40/0x3c8
  sp : ffff000008da39e0
  x29: ffff000008da39e0 x28: 00e8000000000f07
  x27: ffff7dfffee00000 x26: 0140000000000000
  x25: ffff7dfffef00000 x24: 00000000000fe100
  x23: ffff80007b906000 x22: ffff000008ab8000
  x21: ffff000008bb1d58 x20: ffff7dfffef00000
  x19: ffff800009c30fb8 x18: 0000000000000001
  x17: 00000000000152d0 x16: 00000000014012d0
  x15: 0000000000000000 x14: 0720072007200720
  x13: 0720072007200720 x12: 0720072007200720
  x11: 0720072007300730 x10: 00000000000000ae
  x9 : 0000000000000000 x8 : ffff7dffff000000
  x7 : 0000000000000000 x6 : 0000000000000100
  x5 : 0000000000000000 x4 : 000000007b906000
  x3 : ffff80007c61a880 x2 : ffff7dfffeefffff
  x1 : 0000000040000000 x0 : 00e80000fe100f07
  Process kworker/0:1 (pid: 39, stack limit = 0x        (ptrval))
  Call trace:
   ioremap_page_range+0x370/0x3c8
   pci_remap_iospace+0x7c/0xac
   pci_parse_request_of_pci_ranges+0x13c/0x190
   rcar_pcie_probe+0x4c/0xb04
   platform_drv_probe+0x50/0xbc
   driver_probe_device+0x21c/0x308
   __device_attach_driver+0x98/0xc8
   bus_for_each_drv+0x54/0x94
   __device_attach+0xc4/0x12c
   device_initial_probe+0x10/0x18
   bus_probe_device+0x90/0x98
   deferred_probe_work_func+0xb0/0x150
   process_one_work+0x12c/0x29c
   worker_thread+0x200/0x3fc
   kthread+0x108/0x134
   ret_from_fork+0x10/0x18
  Code: f9004ba2 54000080 aa0003fb 17ffff48 (d4210000)

It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.

The Aardvark PCI controller driver has the same issue.
Replace pci_remap_iospace() with its devm_ managed version to fix the bug.

Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/mm: validate VMA in PGSTE manipulation functions

commit fe3d10024073f06f04c74b9674bd71ccc1d787cf upstream.

We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap"). gfn_to_hva() will only translate using
KVM memory regions, but won't validate the VMA.

Further, we should not allocate page tables outside of VMA boundaries: if
evil user space decides to map hugetlbfs to these ranges, bad things will
happen because we suddenly have PTE or PMD page tables where we
shouldn't have them.

Similarly, we have to check if we suddenly find a hugetlbfs VMA, before
calling get_locked_pte().

Fixes: 2d42f9477320 ("s390/kvm: Add PGSTE manipulation functions")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20210909162248.14969-4-david@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Check pid filtering when creating events

commit 6cb206508b621a9a0a2c35b60540e399225c8243 upstream.

When pid filtering is activated in an instance, all of the events trace
files for that instance has the PID_FILTER flag set. This determines
whether or not pid filtering needs to be done on the event, otherwise the
event is executed as normal.

If pid filtering is enabled when an event is created (via a dynamic event
or modules), its flag is not updated to reflect the current state, and the
events are not filtered properly.

Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a836 ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vhost/vsock: fix incorrect used length reported to the guest

commit 49d8c5ffad07ca014cfae72a1b9b8c52b6ad9cb8 upstream.

The "used length" reported by calling vhost_add_used() must be the
number of bytes written by the device (using "in" buffers).

In vhost_vsock_handle_tx_kick() the device only reads the guest
buffers (they are all "out" buffers), without writing anything,
so we must pass 0 as "used length" to comply virtio spec.

Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211122163525.294024-2-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: Don't call clcsock shutdown twice when smc shutdown

[ Upstream commit bacb6c1e47691cda4a95056c21b5487fb7199fcc ]

When applications call shutdown() with SHUT_RDWR in userspace,
smc_close_active() calls kernel_sock_shutdown(), and it is called
twice in smc_shutdown().

This fixes this by checking sk_state before do clcsock shutdown, and
avoids missing the application's call of smc_shutdown().

Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes: 606a63c9783a ("net/smc: Ensure the active closing peer first closes clcsock")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: use 3-level pgtable for 64KB page size on MIPS_VA_BITS_48

[ Upstream commit 41ce097f714401e6ad8f3f5eb30d7f91b0b5e495 ]

It hangup when booting Loongson 3A1000 with BOTH
CONFIG_PAGE_SIZE_64KB and CONFIG_MIPS_VA_BITS_48, that it turn
out to use 2-level pgtable instead of 3-level. 64KB page size
with 2-level pgtable only cover 42 bits VA, use 3-level pgtable
to cover all 48 bits VA(55 bits)

Fixes: 1e321fa917fb ("MIPS64: Support of at least 48 bits of SEGBITS)
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp_cubic: fix spurious Hystart ACK train detections for not-cwnd-limited flows

[ Upstream commit 4e1fddc98d2585ddd4792b5e44433dcee7ece001 ]

While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.

It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.

Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.

Ideally these TCP_RR flows should not exit slow start.

Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.

Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.

Tested:

ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR  -l 5  -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"

Before:

   8605
Ip6InReceives                   87541              0.0
Ip6OutRequests                  129496             0.0
TcpExtTCPHystartTrainDetect     1                  0.0
TcpExtTCPHystartTrainCwnd       30                 0.0

After:

  8760
Ip6InReceives                   88514              0.0
Ip6OutRequests                  87975              0.0

Fixes: ae27e98a5152 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PM: hibernate: use correct mode for swsusp_close()

[ Upstream commit cefcf24b4d351daf70ecd945324e200d3736821e ]

Commit 39fbef4b0f77 ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).

In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.

So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.

Fixes: 39fbef4b0f77 ("PM: hibernate: Get block device exclusively in swsusp_check()")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/smc: Ensure the active closing peer first closes clcsock

[ Upstream commit 606a63c9783a32a45bd2ef0eee393711d75b3284 ]

The side that actively closed socket, it's clcsock doesn't enter
TIME_WAIT state, but the passive side does it. It should show the same
behavior as TCP sockets.

Consider this, when client actively closes the socket, the clcsock in
server enters TIME_WAIT state, which means the address is occupied and
won't be reused before TIME_WAIT dismissing. If we restarted server, the
service would be unavailable for a long time.

To solve this issue, shutdown the clcsock in [A], perform the TCP active
close progress first, before the passive closed side closing it. So that
the actively closed side enters TIME_WAIT, not the passive one.

Client                                            |  Server
close() // client actively close                  |
  smc_release()                                   |
      smc_close_active() // PEERCLOSEWAIT1        |
          smc_close_final() // abort or closed = 1|
              smc_cdc_get_slot_and_msg_send()     |
          [A]                                     |
                                                  |smc_cdc_msg_recv_action() // ACTIVE
                                                  |  queue_work(smc_close_wq, &conn->close_work)
                                                  |    smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1
                                                  |      smc_close_passive_abort_received() // only in abort
                                                  |
                                                  |close() // server recv zero, close
                                                  |  smc_release() // PROCESSABORT or APPCLOSEWAIT1
                                                  |    smc_close_active()
                                                  |      smc_close_abort() or smc_close_final() // CLOSED
                                                  |        smc_cdc_get_slot_and_msg_send() // abort or closed = 1
smc_cdc_msg_recv_action()                         |    smc_clcsock_release()
  queue_work(smc_close_wq, &conn->close_work)     |      sock_release(tcp) // actively close clc, enter TIME_WAIT
    smc_close_passive_work() // PEERCLOSEWAIT1    |    smc_conn_free()
      smc_close_passive_abort_received() // CLOSED|
      smc_conn_free()                             |
      smc_clcsock_release()                       |
        sock_release(tcp) // passive close clc    |

Link: https://www.spinics.net/lists/netdev/msg780407.html
Fixes: b38d732477e4 ("smc: socket closing and linkgroup cleanup")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv6: fix typos in __ip6_finish_output()

[ Upstream commit 19d36c5f294879949c9d6f57cb61d39cc4c48553 ]

We deal with IPv6 packets, so we need to use IP6CB(skb)->flags and
IP6SKB_REROUTED, instead of IPCB(skb)->flags and IPSKB_REROUTED

Found by code inspection, please double check that fixing this bug
does not surface other bugs.

Fixes: 09ee9dba9611 ("ipv6: Reinject IPv6 packets if IPsec policy matches after SNAT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tobias Brunner <tobias@strongswan.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Tested-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/vc4: fix error code in vc4_create_object()

[ Upstream commit 96c5f82ef0a145d3e56e5b26f2bf6dcd2ffeae1c ]

The ->gem_create_object() functions are supposed to return NULL if there
is an error.  None of the callers expect error pointers so returing one
will lead to an Oops.  See drm_gem_vram_create(), for example.

Fixes: c826a6e10644 ("drm/vc4: Add a BO cache.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211118111416.GC1147@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: mpt3sas: Fix kernel panic during drive powercycle test

[ Upstream commit 0ee4ba13e09c9d9c1cb6abb59da8295d9952328b ]

While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.

Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.

Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: socfpga: Fix crash with CONFIG_FORTIRY_SOURCE

[ Upstream commit 187bea472600dcc8d2eb714335053264dd437172 ]

When CONFIG_FORTIFY_SOURCE is set, memcpy() checks the potential
buffer overflow and panics.  The code in sofcpga bootstrapping
contains the memcpy() calls are mistakenly translated as the shorter
size, hence it triggers a panic as if it were overflowing.

This patch changes the secondary_trampoline and *_end definitions
to arrays for avoiding the false-positive crash above.

Fixes: 9c4566a117a6 ("ARM: socfpga: Enable SMP for socfpga")
Suggested-by: Kees Cook <keescook@chromium.org>
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192473
Link: https://lore.kernel.org/r/20211117193244.31162-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFSv42: Don't fail clone() unless the OP_CLONE operation failed

[ Upstream commit d3c45824ad65aebf765fcf51366d317a29538820 ]

The failure to retrieve post-op attributes has no bearing on whether or
not the clone operation itself was successful. We must therefore ignore
the return value of decode_getfattr() when looking at the success or
failure of nfs4_xdr_dec_clone().

Fixes: 36022770de6c ("nfs42: add CLONE xdr functions")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: handle iftypes as u32

[ Upstream commit 451dc48c806a7ce9fbec5e7a24ccf4b2c936e834 ]

This patch fixes an issue that an u32 netlink value is handled as a
signed enum value which doesn't fit into the range of u32 netlink type.
If it's handled as -1 value some BIT() evaluation ends in a
shift-out-of-bounds issue. To solve the issue we set the to u32 max which
is s32 "-1" value to keep backwards compatibility and let the followed enum
values start counting at 0. This brings the compiler to never handle the
enum as signed and a check if the value is above NL802154_IFTYPE_MAX should
filter -1 out.

Fixes: f3ea5e44231a ("ieee802154: add new interface command")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20211112030916.685793-1-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: topology: Add missing rwsem around snd_ctl_remove() calls

[ Upstream commit 7e567b5ae06315ef2d70666b149962e2bb4b97af ]

snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation).  This patch add the missing
rwsem calls around it.

Fixes: 8a9782346dcc ("ASoC: topology: Add topology core")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211116071812.18109-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: BCM5301X: Add interrupt properties to GPIO node

[ Upstream commit 40f7342f0587639e5ad625adaa15efdd3cffb18f ]

The GPIO controller is also an interrupt controller provider and is
currently missing the appropriate 'interrupt-controller' and
'#interrupt-cells' properties to denote that.

Fixes: fb026d3de33b ("ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: BCM5301X: Fix I2C controller interrupt

[ Upstream commit 754c4050a00e802e122690112fc2c3a6abafa7e2 ]

The I2C interrupt controller line is off by 32 because the datasheet
describes interrupt inputs into the GIC which are for Shared Peripheral
Interrupts and are starting at offset 32. The ARM GIC binding expects
the SPI interrupts to be numbered from 0 relative to the SPI base.

Fixes: bb097e3e0045 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipvs: Fix reuse connection if RS weight is 0

[ Upstream commit c95c07836fa4c1767ed11d8eca0769c652760e32 ]

We are changing expire_nodest_conn to work even for reused connections when
conn_reuse_mode=0, just as what was done with commit dc7b3eb900aa ("ipvs:
Fix reuse connection if real server is dead").

For controlled and persistent connections, the new connection will get the
needed real server depending on the rules in ip_vs_check_template().

Fixes: d752c3645717 ("ipvs: allow rescheduling of new connections when port reuse is detected")
Co-developed-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Fix pid filtering when triggers are attached

commit a55f224ff5f238013de8762c4287117e47b86e22 upstream.

If a event is filtered by pid and a trigger that requires processing of
the event to happen is a attached to the event, the discard portion does
not take the pid filtering into account, and the event will then be
recorded when it should not have been.

Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a836 ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: detect uninitialized xenbus in xenbus_init

commit 36e8f60f0867d3b70d398d653c17108459a04efe upstream.

If the xenstore page hasn't been allocated properly, reading the value
of the related hvm_param (HVM_PARAM_STORE_PFN) won't actually return
error. Instead, it will succeed and return zero. Instead of attempting
to xen_remap a bad guest physical address, detect this condition and
return early.

Note that although a guest physical address of zero for
HVM_PARAM_STORE_PFN is theoretically possible, it is not a good choice
and zero has never been validly used in that capacity.

Also recognize all bits set as an invalid value.

For 32-bit Linux, any pfn above ULONG_MAX would get truncated. Pfns
above ULONG_MAX should never be passed by the Xen tools to HVM guests
anyway, so check for this condition and return early.

Cc: stable@vger.kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20211123210748.1910236-1-sstabellini@kernel.org
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: don't continue xenstore initialization in case of errors

commit 08f6c2b09ebd4b326dbe96d13f94fee8f9814c78 upstream.

In case of errors in xenbus_init (e.g. missing xen_store_gfn parameter),
we goto out_error but we forget to reset xen_store_domain_type to
XS_UNKNOWN. As a consequence xenbus_probe_initcall and other initcalls
will still try to initialize xenstore resulting into a crash at boot.

[    2.479830] Call trace:
[    2.482314]  xb_init_comms+0x18/0x150
[    2.486354]  xs_init+0x34/0x138
[    2.489786]  xenbus_probe+0x4c/0x70
[    2.498432]  xenbus_probe_initcall+0x2c/0x7c
[    2.503944]  do_one_initcall+0x54/0x1b8
[    2.507358]  kernel_init_freeable+0x1ac/0x210
[    2.511617]  kernel_init+0x28/0x130
[    2.516112]  ret_from_fork+0x10/0x20

Cc: <Stable@vger.kernel.org>
Cc: jbeulich@suse.com
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Link: https://lore.kernel.org/r/20211115222719.2558207-1-sstabellini@kernel.org
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fuse: fix page stealing

commit 712a951025c0667ff00b25afc360f74e639dfabe upstream.

It is possible to trigger a crash by splicing anon pipe bufs to the fuse
device.

The reason for this is that anon_pipe_buf_release() will reuse buf->page if
the refcount is 1, but that page might have already been stolen and its
flags modified (e.g. PG_lru added).

This happens in the unlikely case of fuse_dev_splice_write() getting around
to calling pipe_buf_release() after a page has been stolen, added to the
page cache and removed from the page cache.

Fix by calling pipe_buf_release() right after the page was inserted into
the page cache.  In this case the page has an elevated refcount so any
release function will know that the page isn't reusable.

Reported-by: Frank Dinoff <fdinoff@google.com>
Link: https://lore.kernel.org/r/CAAmZXrsGg2xsP1CK+cbuEMumtrqdvD-NKnWzhNcvn71RV3c1yw@mail.gmail.com/
Fixes: dd3bb14f44a6 ("fuse: support splice() writing to fuse device")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192e: Fix use after free in _rtl92e_pci_disconnect()

commit b535917c51acc97fb0761b1edec85f1f3d02bda4 upstream.

The free_rtllib() function frees the "dev" pointer so there is use
after free on the next line.  Re-arrange things to avoid that.

Fixes: 66898177e7e5 ("staging: rtl8192e: Fix unload/reload problem")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211117072016.GA5237@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts

commit 7fb0413baa7f8a04caef0c504df9af7e0623d296 upstream.

The HID descriptor of many of Wacom's touch input devices include a
"Confidence" usage that signals if a particular touch collection contains
useful data. The driver does not look at this flag, however, which causes
even invalid contacts to be reported to userspace. A lucky combination of
kernel event filtering and device behavior (specifically: contact ID 0 ==
invalid, contact ID >0 == valid; and order all data so that all valid
contacts are reported before any invalid contacts) spare most devices from
any visibly-bad behavior.

The DTH-2452 is one example of an unlucky device that misbehaves. It uses
ID 0 for both the first valid contact and all invalid contacts. Because
we report both the valid and invalid contacts, the kernel reports that
contact 0 first goes down (valid) and then goes up (invalid) in every
report. This causes ~100 clicks per second simply by touching the screen.

This patch inroduces new `confidence` flag in our `hid_data` structure.
The value is initially set to `true` at the start of a report and can be
set to `false` if an invalid touch usage is seen.

Link: https://github.com/linuxwacom/input-wacom/issues/270
Fixes: f8b6a74719b5 ("HID: wacom: generic: Support multiple tools per report")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: cec: copy sequence field for the reply

commit 13cbaa4c2b7bf9f8285e1164d005dbf08244ecd5 upstream.

When the reply for a non-blocking transmit arrives, the sequence
field for that reply was never filled in, so userspace would have no
way of associating the reply to the original transmit.

Copy the sequence field to ensure that this is now possible.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 0dbacebede1e ([media] cec: move the CEC framework out of staging and to media)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: ctxfi: Fix out-of-range access

commit 76c47183224c86e4011048b80f0e2d0d166f01c2 upstream.

The master and next_conj of rcs_ops are used for iterating the
resource list entries, and currently those are supposed to return the
current value.  The problem is that next_conf may go over the last
entry before the loop abort condition is evaluated, and it may return
the "current" value that is beyond the array size.  It was caught
recently as a GPF, for example.

Those return values are, however, never actually evaluated, hence
basically we don't have to consider the current value as the return at
all.  By dropping those return values, the potential out-of-range
access above is also fixed automatically.

This patch changes the return type of master and next_conj callbacks
to void and drop the superfluous code accordingly.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214985
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211118215729.26257-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix test regression due to sender_euid change

commit c21a80ca0684ec2910344d72556c816cb8940c01 upstream.

This is a partial revert of commit
29bc22ac5e5b ("binder: use euid from cred instead of using task").
Setting sender_euid using proc->cred caused some Android system test
regressions that need further investigation. It is a partial
reversion because subsequent patches rely on proc->cred.

Fixes: 29bc22ac5e5b ("binder: use euid from cred instead of using task")
Cc: stable@vger.kernel.org # 4.4+
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Change-Id: I9b1769a3510fed250bb21859ef8beebabe034c66
Link: https://lore.kernel.org/r/20211112180720.2858135-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub: Fix locking issues with address0_mutex

commit 6cca13de26eea6d32a98d96d916a048d16a12822 upstream.

Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit
ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")

Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex

Fixes: 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Cc: <stable@vger.kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub: Fix usb enumeration issue due to address0 race

commit 6ae6dc22d2d1ce6aa77a6da8a761e61aca216f8b upstream.

xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4

The address0_mutex exists to prevent this across both xhci roothubs.

If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.

Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.

Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.

Cc: <stable@vger.kernel.org>
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Fibocom FM101-GL variants

commit 88459e3e42760abb2299bbf6cb1026491170e02a upstream.

Update the USB serial option driver support for the Fibocom
FM101-GL Cat.6
LTE modules as there are actually several different variants.
- VID:PID 2cb7:01a2, FM101-GL are laptop M.2 cards (with
  MBIM interfaces for /Linux/Chrome OS)
- VID:PID 2cb7:01a4, FM101-GL for laptop debug M.2 cards(with adb
  interface for /Linux/Chrome OS)

0x01a2: mbim, tty, tty, diag, gnss
0x01a4: mbim, diag, tty, adb, gnss, gnss

Here are the outputs of lsusb -v and usb-devices:

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 86 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=2cb7 ProdID=01a2 Rev= 5.04
S:  Manufacturer=Fibocom Wireless Inc.
S:  Product=Fibocom FM101-GL Module
S:  SerialNumber=673326ce
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)

Bus 002 Device 084: ID 2cb7:01a2 Fibocom Wireless Inc. Fibocom FM101-GL Module
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.20
  bDeviceClass            0
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         9
  idVendor           0x2cb7
  idProduct          0x01a2
  bcdDevice            5.04
  iManufacturer           1 Fibocom Wireless Inc.
  iProduct                2 Fibocom FM101-GL Module
  iSerial                 3 673326ce
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x015d
    bNumInterfaces          6
    bConfigurationValue     1
    iConfiguration          4 MBIM_DUN_DUN_DIAG_NMEA
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              896mA
    Interface Association:
      bLength                 8
      bDescriptorType        11
      bFirstInterface         0
      bInterfaceCount         2
      bFunctionClass          2 Communications
      bFunctionSubClass      14
      bFunctionProtocol       0
      iFunction               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass     14
      bInterfaceProtocol      0
      iInterface              5 Fibocom FM101-GL LTE Modem
      CDC Header:
        bcdCDC               1.10
      CDC Union:
        bMasterInterface        0
        bSlaveInterface         1
      CDC MBIM:
        bcdMBIMVersion       1.00
        wMaxControlMessage   4096
        bNumberFilters       32
        bMaxFilterSize       128
        wMaxSegmentSize      2048
        bmNetworkCapabilities 0x20
          8-byte ntb input size
      CDC MBIM Extended:
        bcdMBIMExtendedVersion           1.00
        bMaxOutstandingCommandMessages     64
        wMTU                             1500
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               9
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           0
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0
      bInterfaceProtocol      2
      iInterface              0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       1
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0
      bInterfaceProtocol      2
      iInterface              6 MBIM Data
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8e  EP 14 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               6
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x0f  EP 15 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               2
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol     64
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000a  1x 10 bytes
        bInterval               9
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        3
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol     64
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000a  1x 10 bytes
        bInterval               9
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        4
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol     48
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        5
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol     64
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x88  EP 8 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000a  1x 10 bytes
        bInterval               9
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x87  EP 7 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 85 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=2cb7 ProdID=01a4 Rev= 5.04
S:  Manufacturer=Fibocom Wireless Inc.
S:  Product=Fibocom FM101-GL Module
S:  SerialNumber=673326ce
C:* #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=896mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)

Bus 002 Device 085: ID 2cb7:01a4 Fibocom Wireless Inc. Fibocom FM101-GL Module
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.20
  bDeviceClass            0
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         9
  idVendor           0x2cb7
  idProduct          0x01a4
  bcdDevice            5.04
  iManufacturer           1 Fibocom Wireless Inc.
  iProduct                2 Fibocom FM101-GL Module
  iSerial                 3 673326ce
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x0180
    bNumInterfaces          7
    bConfigurationValue     1
    iConfiguration          4 MBIM_DIAG_DUN_ADB_GNSS_GNSS
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              896mA
    Interface Association:
      bLength                 8
      bDescriptorType        11
      bFirstInterface         0
      bInterfaceCount         2
      bFunctionClass          2 Communications
      bFunctionSubClass      14
      bFunctionProtocol       0
      iFunction               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass     14
      bInterfaceProtocol      0
      iInterface              5 Fibocom FM101-GL LTE Modem
      CDC Header:
        bcdCDC               1.10
      CDC Union:
        bMasterInterface        0
        bSlaveInterface         1
      CDC MBIM:
        bcdMBIMVersion       1.00
        wMaxControlMessage   4096
        bNumberFilters       32
        bMaxFilterSize       128
        wMaxSegmentSize      2048
        bmNetworkCapabilities 0x20
          8-byte ntb input size
      CDC MBIM Extended:
        bcdMBIMExtendedVersion           1.00
        bMaxOutstandingCommandMessages     64
        wMTU                             1500
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               9
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           0
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0
      bInterfaceProtocol      2
      iInterface              0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       1
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0
      bInterfaceProtocol      2
      iInterface              6 MBIM Data
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8e  EP 14 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               6
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x0f  EP 15 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               2
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol     48
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        3
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol     64
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000a  1x 10 bytes
        bInterval               9
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        4
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass     66
      bInterfaceProtocol      1
      iInterface              8 ADB Interface
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        5
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol     64
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x87  EP 7 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000a  1x 10 bytes
        bInterval               9
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        6
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol     64
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x89  EP 9 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000a  1x 10 bytes
        bInterval               9
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x88  EP 8 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x05  EP 5 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0400  1x 1024 bytes
        bInterval               0
        bMaxBurst               0

Signed-off-by: Mingjie Zhang <superzmj@fibocom.com>
Link: https://lore.kernel.org/r/20211123133757.37475-1-superzmj@fibocom.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Telit LE910S1 0x9200 composition

commit e353f3e88720300c3d72f49a4bea54f42db1fa5e upstream.

Add the following Telit LE910S1 composition:

0x9200: tty

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20211119140319.10448-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.256

Link: https://lore.kernel.org/r/20211124115710.214900256@linuxfoundation.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20211125123013.052716101@linuxfoundation.org
Link: https://lore.kernel.org/r/20211125160530.072182872@linuxfoundation.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

soc/tegra: pmc: Fix imbalanced clock disabling in error code path

commit 19221e3083020bd9537624caa0ee0145ed92ba36 upstream.

The tegra_powergate_power_up() has a typo in the error code path where it
will try to disable clocks twice, fix it. In practice that error never
happens, so this is a minor correction.

Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: max-3421: Use driver data instead of maintaining a list of bound devices

commit fc153aba3ef371d0d76eb88230ed4e0dee5b38f2 upstream.

Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.

This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.

As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.

Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: DAPM: Cover regression by kctl change notification fix

commit 827b0913a9d9d07a0c3e559dbb20ca4d6d285a54 upstream.

The recent fix for DAPM to correct the kctl change notification by the
commit 5af82c81b2c4 ("ASoC: DAPM: Fix missing kctl change
notifications") caused other regressions since it changed the behavior
of snd_soc_dapm_set_pin() that is called from several API functions.
Formerly it returned always 0 for success, but now it returns 0 or 1.

This patch addresses it, restoring the old behavior of
snd_soc_dapm_set_pin() while keeping the fix in
snd_soc_dapm_put_pin_switch().

Fixes: 5af82c81b2c4 ("ASoC: DAPM: Fix missing kctl change notifications")
Reported-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211105090925.20575-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/netlink: Add __maybe_unused to static inline in C file

commit 83dde7498fefeb920b1def317421262317d178e5 upstream.

Like other commits in the tree add __maybe_unused to a static inline in a
C file because some clang compilers will complain about unused code:

>> drivers/infiniband/core/nldev.c:2543:1: warning: unused function '__chk_RDMA_NL_NLDEV'
   MODULE_ALIAS_RDMA_NETLINK(RDMA_NL_NLDEV, 5);
   ^

Fixes: e3bf14bdc17a ("rdma: Autoload netlink client modules")
Link: https://lore.kernel.org/r/4a8101919b765e01d7fde6f27fd572c958deeb4a.1636267207.git.leonro@nvidia.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Don't always reallocate the fragmentation skb head

commit 992b03b88e36254e26e9a4977ab948683e21bd9f upstream.

When a packet is fragmented by batman-adv, the original batman-adv header
is not modified. Only a new fragmentation is inserted between the original
one and the ethernet header. The code must therefore make sure that it has
a writable region of this size in the skbuff head.

But it is not useful to always reallocate the skbuff by this size even when
there would be more than enough headroom still in the skb. The reallocation
is just to costly during in this codepath.

Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Reserve needed_*room for fragments

commit c5cbfc87558168ef4c3c27ce36eba6b83391db19 upstream.

The batadv net_device is trying to propagate the needed_headroom and
needed_tailroom from the lower devices. This is needed to avoid cost
intensive reallocations using pskb_expand_head during the transmission.

But the fragmentation code split the skb's without adding extra room at the
end/beginning of the various fragments. This reduced the performance of
transmissions over complex scenarios (batadv on vxlan on wireguard) because
the lower devices had to perform the reallocations at least once.

Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[ bp: 4.14 backported: adjust context. ]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Consider fragmentation for needed_headroom

commit 4ca23e2c2074465bff55ea14221175fecdf63c5f upstream.

If a batman-adv packets has to be fragmented, then the original batman-adv
packet header is not stripped away. Instead, only a new header is added in
front of the packet after it was split.

This size must be considered to avoid cost intensive reallocations during
the transmission through the various device layers.

Fixes: 7bca68c7844b ("batman-adv: Add lower layer needed_(head|tail)room to own ones")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: mcast: fix duplicate mcast packets from BLA backbone to mesh

commit 2369e827046920ef0599e6a36b975ac5c0a359c2 upstream.

Scenario:
* Multicast frame send from BLA backbone gateways (multiple nodes
  with their bat0 bridged together, with BLA enabled) sharing the same
  LAN to nodes in the mesh

Issue:
* Nodes receive the frame multiple times on bat0 from the mesh,
  once from each foreign BLA backbone gateway which shares the same LAN
  with another

For multicast frames via batman-adv broadcast packets coming from the
same BLA backbone but from different backbone gateways duplicates are
currently detected via a CRC history of previously received packets.

However this CRC so far was not performed for multicast frames received
via batman-adv unicast packets. Fixing this by appyling the same check
for such packets, too.

Room for improvements in the future: Ideally we would introduce the
possibility to not only claim a client, but a complete originator, too.
This would allow us to only send a multicast-in-unicast packet from a BLA
backbone gateway claiming the node and by that avoid potential redundant
transmissions in the first place.

Fixes: fe2da6ff27c7 ("batman-adv: add broadcast duplicate check")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[ bp: 4.14 backported: adjust context, correct fixes line ]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: mcast: fix duplicate mcast packets in BLA backbone from LAN

commit 3236d215ad38a3f5372e65cd1e0a52cf93d3c6a2 upstream.

Scenario:
* Multicast frame send from a BLA backbone (multiple nodes with
  their bat0 bridged together, with BLA enabled)

Issue:
* BLA backbone nodes receive the frame multiple times on bat0

For multicast frames received via batman-adv broadcast packets the
originator of the broadcast packet is checked before decapsulating and
forwarding the frame to bat0 (batadv_bla_is_backbone_gw()->
batadv_recv_bcast_packet()). If it came from a node which shares the
same BLA backbone with us then it is not forwarded to bat0 to avoid a
loop.

When sending a multicast frame in a non-4-address batman-adv unicast
packet we are currently missing this check - and cannot do so because
the batman-adv unicast packet has no originator address field.

However, we can simply fix this on the sender side by only sending the
multicast frame via unicasts to interested nodes which do not share the
same BLA backbone with us. This also nicely avoids some unnecessary
transmissions on mesh side.

Note that no infinite loop was observed, probably because of dropping
via batadv_interface_tx()->batadv_bla_tx(). However the duplicates still
utterly confuse switches/bridges, ICMPv6 duplicate address detection and
neighbor discovery and therefore leads to long delays before being able
to establish TCP connections, for instance. And it also leads to the Linux
bridge printing messages like:
"br-lan: received packet on eth1 with own address as source address ..."

Fixes: 1d8ab8d3c176 ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[ bp: 4.14 backport: drop usage in non-existing batadv_mcast_forw_*,
  correct fixes line ]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/core: Avoid put_page() when GUP fails

commit 4716023a8f6a0f4a28047f14dd7ebdc319606b84 upstream.

PEBS PERF_SAMPLE_PHYS_ADDR events use perf_virt_to_phys() to convert PMU
sampled virtual addresses to physical using get_user_page_fast_only()
and page_to_phys().

Some get_user_page_fast_only() error cases return false, indicating no
page reference, but still initialize the output page pointer with an
unreferenced page. In these error cases perf_virt_to_phys() calls
put_page(). This causes page reference count underflow, which can lead
to unintentional page sharing.

Fix perf_virt_to_phys() to only put_page() if get_user_page_fast_only()
returns a referenced page.

Fixes: fc7ce9c74c3ad ("perf/core, x86: Add PERF_SAMPLE_PHYS_ADDR")
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211111021814.757086-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: fix set scaling mode Full/Full aspect/Center not works on vga and dvi connectors

commit bf552083916a7f8800477b5986940d1c9a31b953 upstream.

amdgpu_connector_vga_get_modes missed function amdgpu_get_native_mode
which assign amdgpu_encoder->native_mode with *preferred_mode result in
amdgpu_encoder->native_mode.clock always be 0. That will cause
amdgpu_connector_set_property returned early on:
if ((rmx_type != DRM_MODE_SCALE_NONE) &&
(amdgpu_encoder->native_mode.clock == 0))
when we try to set scaling mode Full/Full aspect/Center.
Add the missing function to amdgpu_connector_vga_get_mode can fix this.
It also works on dvi connectors because
amdgpu_connector_dvi_helper_funcs.get_mode use the same method.

Signed-off-by: hongao <hongao@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/udl: fix control-message timeout

commit 5591c8f79db1729d9c5ac7f5b4d3a5c26e262d93 upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 5320918b9a87 ("drm/udl: initial UDL driver (v4)")
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025115353.5089-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: call cfg80211_stop_ap when switch from P2P_GO type

commit 563fbefed46ae4c1f70cffb8eb54c02df480b2c2 upstream.

If the userspace tools switch from NL80211_IFTYPE_P2P_GO to
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), it
does not call the cleanup cfg80211_stop_ap(), this leads to the
initialization of in-use data. For example, this path re-init the
sdata->assigned_chanctx_list while it is still an element of
assigned_vifs list, and makes that linked list corrupt.

Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+bbf402b783eeb6d908db@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211027173722.777287-1-phind.uet@gmail.com
Cc: stable@vger.kernel.org
Fixes: ac800140c20e ("cfg80211: .stop_ap when interface is going down")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc/sticon: fix reverse colors

commit bec05f33ebc1006899c6d3e59a00c58881fe7626 upstream.

sticon_build_attr() checked the reverse argument and flipped
background and foreground color, but returned the non-reverse
value afterwards. Fix this and also add two local variables
for foreground and background color to make the code easier
to read.

Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix memory ordering between normal and ordered work functions

commit 45da9c1767ac31857df572f0a909fbe88fd5a7e9 upstream.

Ordered work functions aren't guaranteed to be handled by the same thread
which executed the normal work functions. The only way execution between
normal/ordered functions is synchronized is via the WORK_DONE_BIT,
unfortunately the used bitops don't guarantee any ordering whatsoever.

This manifested as seemingly inexplicable crashes on ARM64, where
async_chunk::inode is seen as non-null in async_cow_submit which causes
submit_compressed_extents to be called and crash occurs because
async_chunk::inode suddenly became NULL. The call trace was similar to:

    pc : submit_compressed_extents+0x38/0x3d0
    lr : async_cow_submit+0x50/0xd0
    sp : ffff800015d4bc20

    <registers omitted for brevity>

    Call trace:
     submit_compressed_extents+0x38/0x3d0
     async_cow_submit+0x50/0xd0
     run_ordered_work+0xc8/0x280
     btrfs_work_helper+0x98/0x250
     process_one_work+0x1f0/0x4ac
     worker_thread+0x188/0x504
     kthread+0x110/0x114
     ret_from_fork+0x10/0x18

Fix this by adding respective barrier calls which ensure that all
accesses preceding setting of WORK_DONE_BIT are strictly ordered before
setting the flag. At the same time add a read barrier after reading of
WORK_DONE_BIT in run_ordered_work which ensures all subsequent loads
would be strictly ordered after reading the bit. This in turn ensures
are all accesses before WORK_DONE_BIT are going to be strictly ordered
before any access that can occur in ordered_func.

Reported-by: Chris Murphy <lists@colorremedies.com>
Fixes: 08a9ff326418 ("btrfs: Added btrfs_workqueue_struct implemented ordered execution based on kernel workqueue")
CC: stable@vger.kernel.org # 4.4+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2011928
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Tested-by: Chris Murphy <chris@colorremedies.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: kmemleak: slob: respect SLAB_NOLEAKTRACE flag

commit 34dbc3aaf5d9e89ba6cc5e24add9458c21ab1950 upstream.

When kmemleak is enabled for SLOB, system does not boot and does not
print anything to the console.  At the very early stage in the boot
process we hit infinite recursion from kmemleak_init() and eventually
kernel crashes.

kmemleak_init() specifies SLAB_NOLEAKTRACE for KMEM_CACHE(), but
kmem_cache_create_usercopy() removes it because CACHE_CREATE_MASK is not
valid for SLOB.

Let's fix CACHE_CREATE_MASK and make kmemleak work with SLOB

Link: https://lkml.kernel.org/r/20211115020850.3154366-1-rkovhaev@gmail.com
Fixes: d8843922fba4 ("slab: Ignore internal flags in cache creation")
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Glauber Costa <glommer@parallels.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hexagon: export raw I/O routines for modules

commit ffb92ce826fd801acb0f4e15b75e4ddf0d189bde upstream.

Patch series "Fixes for ARCH=hexagon allmodconfig", v2.

This series fixes some issues noticed with ARCH=hexagon allmodconfig.

This patch (of 3):

When building ARCH=hexagon allmodconfig, the following errors occur:

  ERROR: modpost: "__raw_readsl" [drivers/i3c/master/svc-i3c-master.ko] undefined!
  ERROR: modpost: "__raw_writesl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
  ERROR: modpost: "__raw_readsl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
  ERROR: modpost: "__raw_writesl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!
  ERROR: modpost: "__raw_readsl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!

Export these symbols so that modules can use them without any errors.

Link: https://lkml.kernel.org/r/20211115174250.1994179-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20211115174250.1994179-2-nathan@kernel.org
Fixes: 013bf24c3829 ("Hexagon: Provide basic implementation and/or stubs for I/O routines.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tun: fix bonding active backup with arp monitoring

commit a31d27fbed5d518734cb60956303eb15089a7634 upstream.

As stated in the bonding doc, trans_start must be set manually for drivers
using NETIF_F_LLTX:
 Drivers that use NETIF_F_LLTX flag must also update
 netdev_queue->trans_start. If they do not, then the ARP monitor will
 immediately fail any slaves using that driver, and those slaves will stay
 down.

Link: https://www.kernel.org/doc/html/v5.15/networking/bonding.html#arp-monitor-operation
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/intel/uncore: Fix IIO event constraints for Skylake Server

[ Upstream commit 3866ae319c846a612109c008f43cba80b8c15e86 ]

According to the latest uncore document, COMP_BUF_OCCUPANCY (0xd5) event
can be collected on 2-3 counters. Update uncore IIO event constraints for
Skylake Server.

Fixes: cd34cd97b7b4 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20211115090334.3789-3-alexander.antonov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf/x86/intel/uncore: Fix filter_tid mask for CHA events on Skylake Server

[ Upstream commit e324234e0aa881b7841c7c713306403e12b069ff ]

According Uncore Reference Manual: any of the CHA events may be filtered
by Thread/Core-ID by using tid modifier in CHA Filter 0 Register.
Update skx_cha_hw_config() to follow Uncore Guide.

Fixes: cd34cd97b7b4 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20211115090334.3789-2-alexander.antonov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFC: reorder the logic in nfc_{un,}register_device

[ Upstream commit 3e3b5dfcd16a3e254aab61bd1e8c417dd4503102 ]

There is a potential UAF between the unregistration routine and the NFC
netlink operations.

The race that cause that UAF can be shown as below:

 (FREE)                      |  (USE)
nfcmrvl_nci_unregister_dev   |  nfc_genl_dev_up
  nci_close_device           |
  nci_unregister_device      |    nfc_get_device
    nfc_unregister_device    |    nfc_dev_up
      rfkill_destory         |
      device_del             |      rfkill_blocked
  ...                        |    ...

The root cause for this race is concluded below:
1. The rfkill_blocked (USE) in nfc_dev_up is supposed to be placed after
the device_is_registered check.
2. Since the netlink operations are possible just after the device_add
in nfc_register_device, the nfc_dev_up() can happen anywhere during the
rfkill creation process, which leads to data race.

This patch reorder these actions to permit
1. Once device_del is finished, the nfc_dev_up cannot dereference the
rfkill object.
2. The rfkill_register need to be placed after the device_add of nfc_dev
because the parent device need to be created first. So this patch keeps
the order but inject device_lock to prevent the data race.

Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: be055b2f89b5 ("NFC: RFKILL support")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152652.19217-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFC: reorganize the functions in nci_request

[ Upstream commit 86cdf8e38792545161dbe3350a7eced558ba4d15 ]

There is a possible data race as shown below:

thread-A in nci_request()       | thread-B in nci_close_device()
                                | mutex_lock(&ndev->req_lock);
test_bit(NCI_UP, &ndev->flags); |
...                             | test_and_clear_bit(NCI_UP, &ndev->flags)
mutex_lock(&ndev->req_lock);    |
                                |

This race will allow __nci_request() to be awaked while the device is
getting removed.

Similar to commit e2cb6b891ad2 ("bluetooth: eliminate the potential race
condition when removing the HCI controller"). this patch alters the
function sequence in nci_request() to prevent the data races between the
nci_close_device().

Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf50c ("NFC: basic NCI protocol implementation")
Link: https://lore.kernel.org/r/20211115145600.8320-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: Fix NULL ptr dereference on VSI filter sync

[ Upstream commit 37d9e304acd903a445df8208b8a13d707902dea6 ]

Remove the reason of null pointer dereference in sync VSI filters.
Added new I40E_VSI_RELEASING flag to signalize deleting and releasing
of VSI resources to sync this thread with sync filters subtask.
Without this patch it is possible to start update the VSI filter list
after VSI is removed, that's causing a kernel oops.

Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: virtio_net_hdr_to_skb: count transport header in UFO

[ Upstream commit cf9acc90c80ecbee00334aa85d92f4e74014bcff ]

virtio_net_hdr_to_skb does not set the skb's gso_size and gso_type
correctly for UFO packets received via virtio-net that are a little over
the GSO size. This can lead to problems elsewhere in the networking
stack, e.g. ovs_vport_send dropping over-sized packets if gso_size is
not set.

This is due to the comparison

  if (skb->len - p_off > gso_size)

not properly accounting for the transport layer header.

p_off includes the size of the transport layer header (thlen), so
skb->len - p_off is the size of the TCP/UDP payload.

gso_size is read from the virtio-net header. For UFO, fragmentation
happens at the IP level so does not need to include the UDP header.

Hence the calculation could be comparing a TCP/UDP payload length with
an IP payload length, causing legitimate virtio-net packets to have
lack gso_type/gso_size information.

Example: a UDP packet with payload size 1473 has IP payload size 1481.
If the guest used UFO, it is not fragmented and the virtio-net header's
flags indicate that it is a GSO frame (VIRTIO_NET_HDR_GSO_UDP), with
gso_size = 1480 for an MTU of 1500.  skb->len will be 1515 and p_off
will be 42, so skb->len - p_off = 1473.  Hence the comparison fails, and
shinfo->gso_size and gso_type are not set as they should be.

Instead, add the UDP header length before comparing to gso_size when
using UFO. In this way, it is the size of the IP payload that is
compared to gso_size.

Fixes: 6dd912f82680 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Jonathan Davies <jonathan.davies@nutanix.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: hp_accel: Fix an error handling path in 'lis3lv02d_probe()'

[ Upstream commit c961a7d2aa23ae19e0099fbcdf1040fb760eea83 ]

If 'led_classdev_register()' fails, some additional resources should be
released.

Add the missing 'i8042_remove_filter()' and 'lis3lv02d_remove_fs()' calls
that are already in the remove function but are missing here.

Fixes: a4c724d0723b ("platform: hp_accel: add a i8042 filter to remove HPQ6000 data from kb bus stream")
Fixes: 9e0c79782143 ("lis3lv02d: merge with leds hp disk")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/5a4f218f8f16d2e3a7906b7ca3654ffa946895f8.1636314074.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mips: lantiq: add support for clk_get_parent()

[ Upstream commit fc1aabb088860d6cf9dd03612b7a6f0de91ccac2 ]

Provide a simple implementation of clk_get_parent() in the
lantiq subarch so that callers of it will build without errors.

Fixes this build error:
ERROR: modpost: "clk_get_parent" [drivers/iio/adc/ingenic-adc.ko] undefined!

Fixes: 171bb2f19ed6 ("MIPS: Lantiq: Add initial support for Lantiq SoCs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: John Crispin <john@phrozen.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mips: bcm63xx: add support for clk_get_parent()

[ Upstream commit e8f67482e5a4bc8d0b65d606d08cb60ee123b468 ]

BCM63XX selects HAVE_LEGACY_CLK but does not provide/support
clk_get_parent(), so add a simple implementation of that
function so that callers of it will build without errors.

Fixes these build errors:

mips-linux-ld: drivers/iio/adc/ingenic-adc.o: in function `jz4770_adc_init_clk_div':
ingenic-adc.c:(.text+0xe4): undefined reference to `clk_get_parent'
mips-linux-ld: drivers/iio/adc/ingenic-adc.o: in function `jz4725b_adc_init_clk_div':
ingenic-adc.c:(.text+0x1b8): undefined reference to `clk_get_parent'

Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs." )
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Artur Rojek <contact@artur-rojek.eu>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@vger.kernel.org
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-iio@vger.kernel.org
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: generic/yamon-dt: fix uninitialized variable error

[ Upstream commit 255e51da15baed47531beefd02f222e4dc01f1c1 ]

In the case where fw_getenv returns an error when fetching values
for ememsizea and memsize then variable phys_memsize is not assigned
a variable and will be uninitialized on a zero check of phys_memsize.
Fix this by initializing phys_memsize to zero.

Cleans up cppcheck error:
arch/mips/generic/yamon-dt.c:100:7: error: Uninitialized variable: phys_memsize [uninitvar]

Fixes: f41d2430bbd6 ("MIPS: generic/yamon-dt: Support > 256MB of RAM")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iavf: Fix for the false positive ASQ/ARQ errors while issuing VF reset

[ Upstream commit 321421b57a12e933f92b228e0e6d0b2c6541f41d ]

While issuing VF Reset from the guest OS, the VF driver prints
logs about critical / Overflow error detection. This is not an
actual error since the VF_MBX_ARQLEN register is set to all FF's
for a short period of time and the VF would catch the bits set if
it was reading the register during that spike of time.
This patch introduces an additional check to ignore this condition
since the VF is in reset.

Fixes: 19b73d8efaa4 ("i40evf: Add additional check for reset")
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: bnx2x: fix variable dereferenced before check

[ Upstream commit f8885ac89ce310570e5391fe0bf0ec9c7c9b4fdc ]

Smatch says:
bnx2x_init_ops.h:640 bnx2x_ilt_client_mem_op()
warn: variable dereferenced before check 'ilt' (see line 638)

Move ilt_cli variable initialization _after_ ilt validation, because
it's unsafe to deref the pointer before validation check.

Fixes: 523224a3b3cd ("bnx2x, cnic, bnx2i: use new FW/HSI")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/core: Mitigate race cpus_share_cache()/update_top_cache_domain()

[ Upstream commit 42dc938a590c96eeb429e1830123fef2366d9c80 ]

Nothing protects the access to the per_cpu variable sd_llc_id. When testing
the same CPU (i.e. this_cpu == that_cpu), a race condition exists with
update_top_cache_domain(). One scenario being:

              CPU1                            CPU2
  ==================================================================

  per_cpu(sd_llc_id, CPUX) => 0
                                    partition_sched_domains_locked()
             detach_destroy_domains()
  cpus_share_cache(CPUX, CPUX)          update_top_cache_domain(CPUX)
    per_cpu(sd_llc_id, CPUX) => 0
                                          per_cpu(sd_llc_id, CPUX) = CPUX
    per_cpu(sd_llc_id, CPUX) => CPUX
    return false

ttwu_queue_cond() wouldn't catch smp_processor_id() == cpu and the result
is a warning triggered from ttwu_queue_wakelist().

Avoid a such race in cpus_share_cache() by always returning true when
this_cpu == that_cpu.

Fixes: 518cd6234178 ("sched: Only queue remote wakeups when crossing cache boundaries")
Reported-by: Jing-Ting Wu <jing-ting.wu@mediatek.com>
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20211104175120.857087-1-vincent.donnefort@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mips: BCM63XX: ensure that CPU_SUPPORTS_32BIT_KERNEL is set

[ Upstream commit 5eeaafc8d69373c095e461bdb39e5c9b62228ac5 ]

Several header files need info on CONFIG_32BIT or CONFIG_64BIT,
but kconfig symbol BCM63XX does not provide that info. This leads
to many build errors, e.g.:

   arch/mips/include/asm/page.h:196:13: error: use of undeclared identifier 'CAC_BASE'
           return x - PAGE_OFFSET + PHYS_OFFSET;
   arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
   #define PAGE_OFFSET             (CAC_BASE + PHYS_OFFSET)
   arch/mips/include/asm/io.h:134:28: error: use of undeclared identifier 'CAC_BASE'
           return (void *)(address + PAGE_OFFSET - PHYS_OFFSET);
   arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
   #define PAGE_OFFSET             (CAC_BASE + PHYS_OFFSET)

arch/mips/include/asm/uaccess.h:82:10: error: use of undeclared identifier '__UA_LIMIT'
           return (__UA_LIMIT & (addr | (addr + size) | __ua_size(size))) == 0;

Selecting the SYS_HAS_CPU_BMIPS* symbols causes SYS_HAS_CPU_BMIPS to be
set, which then selects CPU_SUPPORT_32BIT_KERNEL, which causes
CONFIG_32BIT to be set. (a bit more indirect than v1 [RFC].)

Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-mips@vger.kernel.org
Cc: Paul Burton <paulburton@kernel.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sh: define __BIG_ENDIAN for math-emu

[ Upstream commit b929926f01f2d14635345d22eafcf60feed1085e ]

Fix this by defining both ENDIAN macros in
<asm/sfp-machine.h> so that they can be utilized in
<math-emu/soft-fp.h> according to the latter's comment:
/* Allow sfp-machine to have its own byte order definitions. */

(This is what is done in arch/nds32/include/asm/sfp-machine.h.)

This placates these build warnings:

In file included from ../arch/sh/math-emu/math.c:23:
.../include/math-emu/single.h:50:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
   50 | #if __BYTE_ORDER == __BIG_ENDIAN
In file included from ../arch/sh/math-emu/math.c:24:
.../include/math-emu/double.h:59:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
   59 | #if __BYTE_ORDER == __BIG_ENDIAN

Fixes: 4b565680d163 ("sh: math-emu support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sh: fix kconfig unmet dependency warning for FRAME_POINTER

[ Upstream commit fda1bc533094a7db68b11e7503d2c6c73993d12a ]

FRAME_POINTER depends on DEBUG_KERNEL so DWARF_UNWINDER should
depend on DEBUG_KERNEL before selecting FRAME_POINTER.

WARNING: unmet direct dependencies detected for FRAME_POINTER
  Depends on [n]: DEBUG_KERNEL [=n] && (M68K || UML || SUPERH [=y]) || ARCH_WANT_FRAME_POINTERS [=n]
  Selected by [y]:
  - DWARF_UNWINDER [=y]

Fixes: bd353861c735 ("sh: dwarf unwinder support.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

maple: fix wrong return value of maple_bus_init().

[ Upstream commit bde82ee391fa6d3ad054313c4aa7b726d32515ce ]

If KMEM_CACHE or maple_alloc_dev failed, the maple_bus_init() will return 0
rather than error, because the retval is not changed after KMEM_CACHE or
maple_alloc_dev failed.

Fixes: 17be2d2b1c33 ("sh: Add maple bus support for the SEGA Dreamcast.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sh: check return code of request_irq

[ Upstream commit 0e38225c92c7964482a8bb6b3e37fde4319e965c ]

request_irq is marked __must_check, but the call in shx3_prepare_cpus
has a void return type, so it can't propagate failure to the caller.
Follow cues from hexagon and just print an error.

Fixes: c7936b9abcf5 ("sh: smp: Hook in to the generic IPI handler for SH-X3 SMP.")
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/dcr: Use cmplwi instead of 3-argument cmpli

[ Upstream commit fef071be57dc43679a32d5b0e6ee176d6f12e9f2 ]

In dcr-low.S we use cmpli with three arguments, instead of four
arguments as defined in the ISA:

cmpli cr0,r3,1024

This appears to be a PPC440-ism, looking at the "PPC440x5 CPU Core
User’s Manual" it shows cmpli having no L field, but implied to be 0 due
to the core being 32-bit. It mentions that the ISA defines four
arguments and recommends using cmplwi.

It also corresponds to the old POWER instruction set, which had no L
field there, a reserved bit instead.

dcr-low.S is only built 32-bit, because it is only built when
DCR_NATIVE=y, which is only selected by 40x and 44x. Looking at the
generated code (with gcc/gas) we see cmplwi as expected.

Although gas is happy with the 3-argument version when building for
32-bit, the LLVM assembler is not and errors out with:

  arch/powerpc/sysdev/dcr-low.S:27:10: error: invalid operand for instruction
   cmpli 0,%r3,1024; ...
           ^

Switch to the cmplwi extended opcode, which avoids any confusion when
reading the ISA, fixes the issue with the LLVM assembler, and also means
the code could be built 64-bit in future (though that's very unlikely).

Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
BugLink: https://github.com/ClangBuiltLinux/linux/issues/1419
Link: https://lore.kernel.org/r/20211014024424.528848-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: gus: fix null pointer dereference on pointer block

[ Upstream commit a0d21bb3279476c777434c40d969ea88ca64f9aa ]

The pointer block return from snd_gf1_dma_next_block could be
null, so there is a potential null pointer dereference issue.
Fix this by adding a null check before dereference.

Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Link: https://lore.kernel.org/r/20211024104611.9919-1-cyeaa@connect.ust.hk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/5200: dts: fix memory node unit name

[ Upstream commit aed2886a5e9ffc8269a4220bff1e9e030d3d2eb1 ]

Fixes build warnings:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211013220532.24759-4-agust@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: target: Fix alua_tg_pt_gps_count tracking

[ Upstream commit 1283c0d1a32bb924324481586b5d6e8e76f676ba ]

We can't free the tg_pt_gp in core_alua_set_tg_pt_gp_id() because it's
still accessed via configfs. Its release must go through the normal
configfs/refcount process.

The max alua_tg_pt_gps_count check should probably have been done in
core_alua_allocate_tg_pt_gp(), but with the current code userspace could
have created 0x0000ffff + 1 groups, but only set the id for 0x0000ffff.
Then it could have deleted a group with an ID set, and then set the ID for
that extra group and it would work ok.

It's unlikely, but just in case this patch continues to allow that type of
behavior, and just fixes the kfree() while in use bug.

Link: https://lore.kernel.org/r/20210930020422.92578-4-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: target: Fix ordered tag handling

[ Upstream commit ed1227e080990ffec5bf39006ec8a57358e6689a ]

This patch fixes the following bugs:

1. If there are multiple ordered cmds queued and multiple simple cmds
   completing, target_restart_delayed_cmds() could be called on different
   CPUs and each instance could start a ordered cmd. They could then run in
   different orders than they were queued.

2. target_restart_delayed_cmds() and target_handle_task_attr() can race
   where:

   1. target_handle_task_attr() has passed the simple_cmds == 0 check.

   2. transport_complete_task_attr() then decrements simple_cmds to 0.

   3. transport_complete_task_attr() runs target_restart_delayed_cmds() and
      it does not see any cmds on the delayed_cmd_list.

   4. target_handle_task_attr() adds the cmd to the delayed_cmd_list.

   The cmd will then end up timing out.

3. If we are sent > 1 ordered cmds and simple_cmds == 0, we can execute
   them out of order, because target_handle_task_attr() will hit that
   simple_cmds check first and return false for all ordered cmds sent.

4. We run target_restart_delayed_cmds() after every cmd completion, so if
   there is more than 1 simple cmd running, we start executing ordered cmds
   after that first cmd instead of waiting for all of them to complete.

5. Ordered cmds are not supposed to start until HEAD OF QUEUE and all older
   cmds have completed, and not just simple.

6. It's not a bug but it doesn't make sense to take the delayed_cmd_lock
   for every cmd completion when ordered cmds are almost never used. Just
   replacing that lock with an atomic increases IOPs by up to 10% when
   completions are spread over multiple CPUs and there are multiple
   sessions/ mqs/thread accessing the same device.

This patch moves the queued delayed handling to a per device work to
serialze the cmd executions for each device and adds a new counter to track
HEAD_OF_QUEUE and SIMPLE cmds. We can then check the new counter to
determine when to run the work on the completion path.

Link: https://lore.kernel.org/r/20210930020422.92578-3-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: sni: Fix the build

[ Upstream commit c91cf42f61dc77b289784ea7b15a8531defa41c0 ]

This patch fixes the following gcc 10 build error:

arch/mips/sni/time.c: In function ‘a20r_set_periodic’:
arch/mips/sni/time.c:15:26: error: unsigned conversion from ‘int’ to ‘u8’ {aka ‘volatile unsigned char’} changes value from ‘576’ to ‘64’ [-Werror=overflow]
   15 | #define SNI_COUNTER0_DIV ((SNI_CLOCK_TICK_RATE / SNI_COUNTER2_DIV) / HZ)
      |                          ^
arch/mips/sni/time.c:21:45: note: in expansion of macro ‘SNI_COUNTER0_DIV’
   21 |  *(volatile u8 *)(A20R_PT_CLOCK_BASE + 0) = SNI_COUNTER0_DIV;
      |                                             ^~~~~~~~~~~~~~~~

Cc: linux-mips@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: tty_buffer: Fix the softlockup issue in flush_to_ldisc

[ Upstream commit 3968ddcf05fb4b9409cd1859feb06a5b0550a1c1 ]

When running ltp testcase(ltp/testcases/kernel/pty/pty04.c) with arm64, there is a soft lockup,
which look like this one:

  Workqueue: events_unbound flush_to_ldisc
  Call trace:
   dump_backtrace+0x0/0x1ec
   show_stack+0x24/0x30
   dump_stack+0xd0/0x128
   panic+0x15c/0x374
   watchdog_timer_fn+0x2b8/0x304
   __run_hrtimer+0x88/0x2c0
   __hrtimer_run_queues+0xa4/0x120
   hrtimer_interrupt+0xfc/0x270
   arch_timer_handler_phys+0x40/0x50
   handle_percpu_devid_irq+0x94/0x220
   __handle_domain_irq+0x88/0xf0
   gic_handle_irq+0x84/0xfc
   el1_irq+0xc8/0x180
   slip_unesc+0x80/0x214 [slip]
   tty_ldisc_receive_buf+0x64/0x80
   tty_port_default_receive_buf+0x50/0x90
   flush_to_ldisc+0xbc/0x110
   process_one_work+0x1d4/0x4b0
   worker_thread+0x180/0x430
   kthread+0x11c/0x120

In the testcase pty04, The first process call the write syscall to send
data to the pty master. At the same time, the workqueue will do the
flush_to_ldisc to pop data in a loop until there is no more data left.
When the sender and workqueue running in different core, the sender sends
data fastly in full time which will result in workqueue doing work in loop
for a long time and occuring softlockup in flush_to_ldisc with kernel
configured without preempt. So I add need_resched check and cond_resched
in the flush_to_ldisc loop to avoid it.

Signed-off-by: Guanghui Feng <guanghuifeng@linux.alibaba.com>
Link: https://lore.kernel.org/r/1633961304-24759-1-git-send-email-guanghuifeng@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: host: ohci-tmio: check return value after calling platform_get_resource()

[ Upstream commit 9eff2b2e59fda25051ab36cd1cb5014661df657b ]

It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211011134920.118477-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>