rt2800: rearrange bbp/rfcsr initialization

This makes order of initialization of various registers similar like
on vendor driver.

Based on:
NICInitializeAsic()
RT5592LoadRFNormalModeSetup()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chip/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: add iq calibration

Based on:
GetIQCalibration()
IQCalibration()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rtmp_chip.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: more channel switch registers settings (BBP & GLRT)

Based on:
RT5592_ChipSwitchChannel()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: enable rf init

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: setup LDO_CFG0 when configuring channel

Based on:
RT5592_ChipSwitchChannel()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: init frequency calibration

Based on:
InitFrequencyCalibrationMode()
RT5592_ChipCap

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/frq_cal.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: initialize RF_38/39/30 registers

Based on:
RT5592LoadRFNormalModeSetup()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: initialize BBP_R138 register

Based on:
RT5592LoadRFNormalModeSetup()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: initalize BBP_R103 register on new revisions

Based on:
NICInitRT5592RFRegisters()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: initalize RF_R27 on older revisions

Based on:
NICInitRT5592RFRegisters()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: RF early registers initialization

Based on:
NICInitRT5592RFRegisters()
RF5592Reg_2G_5G[]

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

This patch also merge common frequency adjustment (RF_R17 settings)
code. Further work is needed, to setup more RF/BBP/MAC registers after
that.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: common BBP initialization

Add BBP registers initialization common with other chipsets, but for now
performed only for 5592.

Based on:
NICInitBBP()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: BBP registers initialization

Based on:
NICInitRT5592BbpRegisters()
NICInitBBP()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: MAC registers initalization

Based on:
NICInitRT5592MacRegisters()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

On vendor driver we do not initialize TX_SW_CFG{1,2}. However the same
difference is between rt2x00 and vendor driver for 5390 chip.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: channel config stub

Based on:
RT5592_ChipSwitchChannel()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: add channels table

Based on:
RT5592_ChipSwitchChannel()
RT5592_Frequency_Plan_Xtal20M[]
RT5592_Frequency_Plan_Xtal40M[]

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: 5592: early defines

Add basic defines for 5592 chip. It can not be enabled until
CONFIG_RT2800USB_RT55XX configuration option will be provided in the
Kconfig.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: do not crash if spec->channels is NULL

In case the spec->channels was not specified, print warning instead
of hard crash the kernel.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix tx status reporting for reordered frames in rt2800pci

rt2800 hardware sometimes reorders tx frames when transmitting to
multiple BA enabled STAs concurrently.

For example a tx queue
[ STA1 | STA2 | STA1 | STA2 ]
can result in the tx status reports
[ STA1 | STA1 | STA2 | STA2 ]
when the hw decides to put the frames for STA1 in one AMPDU.

To mitigate this effect associate the currently processed tx status
to the first frame in the tx queue with a matching wcid.

This patch fixes several problems related to incorrect tx status
reporting. Furthermore the tx rate selection is much more stable when
communicating with multiple STAs.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Revert "rt2x00: remove unused argument"

This reverts commit db36f792370959ff26458f80942cf98fe8249d95
since I'm going to use the data pointer that was removed in
a follow up patch.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: cleanup VHT cap

Firmware returned VHT cap has the same format that cfg80211
expects. There is no need to parse the vht cap from the firmware
and then set it to ieee80211_sta_vht_cap. Just copying is
sufficient.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'for-linville-20130318' of git://github.com/kvalo/ath6kl

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
net/nfc/llcp/llcp.c

ath6kl: Fix a debugfs crash for USB devices

Credit distribution stats is currently implemented
only for SDIO. This fixes a crash in debugfs for
USB interface.

BUG: unable to handle kernel NULL pointer dereference at   (null)
IP: [<f91c2048>] read_file_credit_dist_stats+0x38/0x330 [ath6kl_core]
*pde = b62bd067
Oops: 0000 [#1] SMP

EIP: 0060:[<f91c2048>] EFLAGS: 00210246 CPU: 0
EIP is at read_file_credit_dist_stats+0x38/0x330 [ath6kl_core]
EAX: 00000000 EBX: e6f7a9c0 ECX: e7b148b8 EDX: 00000000
ESI: 000000c8 EDI: e7b14000 EBP: e6e09f64 ESP: e6e09f30
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process cat (pid: 4058, ti=e6e08000 task=e50cf230 task.ti=e6e08000)
Stack:
00008000 00000000 e6e09f64 c1132d3c 00004e71 e50cf230 00008000 089e4000
e7b148b8 00000000 e6f7a9c0 00008000 089e4000 e6e09f8c c11331fc e6e09f98
00000001 e6e09f7c f91c2010 e6e09fac e6f7a9c0 089e4877 089e4000 e6e09fac

Call Trace:
[<c1132d3c>] ? rw_verify_area+0x6c/0x120
[<c11331fc>] vfs_read+0x8c/0x160
[<f91c2010>] ? read_file_war_stats+0x130/0x130 [ath6kl_core]
[<c113330d>] sys_read+0x3d/0x70
[<c15755b4>] syscall_call+0x7/0xb
[<c1570000>] ? fill_powernow_table_pstate+0x127/0x127

Cc: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath: changed kmalloc to kmemdup

Signed-off-by: Andrei Epure <epure.andrei@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Fix the byte alignment rule to avoid loss of bytes in a TCP segment

Either first 3 bytes of the first received tcp segment or last one
over MTU size file can be loss due to the byte alignment problem.
Although ATH6KL_HTC_ALIGN_BYTES was defined for 'extra bytes for htc header
alignment' in the patch "Fix buffer alignment for scatter-gather
I/O"(1df94a857), there exists the bytes loss issue which means that it will be
truncated 3 bytes in the transmitted file contents if a file which has over MTU
size is transferred through TCP/IP stack.  It doesn't look like TCP/IP stack
bug of 3.5 or the latest version of kernel but the byte alignment issue.  This
patch is to use the roundup() function for the byte alignment rather than the
predefined ATH6KL_HTC_ALIGN_BYTES.

kvalo: fixed indentation

Signed-off-by: Myoungje Kim <mjei78@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: remove false check from ath6kl_rx()

Dan found a check from ath6kl_rx() which doesn't make any sense at all:

"  1327          if (status || !(skb->data + HTC_HDR_LENGTH)) {
                                ^^^^^^^^^^^^^^^^^^^^^^^^^^
skb->data is a pointer.  This pointer math is always going to be false.
Should it be testing "packet->act_len < HTC_HDR_LENGTH" or something?"

I don't know what the check really was supposed to do, but I think Dan's guess
is right. Fix it accordingly.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add an extra band check to ath6kl_wmi_beginscan_cmd()

Dan reported that smatch found a possible issue in ath6kl_wmi_beginscan_cmd()
where we might access sc->supp_rates beyond the end. It shouldn't happen as
ar->wiphy->bands always have just the first two bands set, but add an extra
check just to be sure.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add tracing support to debug message macros

Now all log messages are sent through the tracing infrastruture as well.
Tracing point doesn't follow debug_mask module parameter, instead it sends
all debug messages, so once you enable ath6kl_log_dbg tracing point you will
get a lot of messages. Needs to be discussed if this is sensible or not.
The overhead should be small enough and we anyway include debug level as
well so it's easy to filter in user space.

I wasn't really sure what to do with ath6kl_dbg_dump() and for now decided
that it also sends the buffer to user space. But most likely in the future
ath6kl_dbg_dump() should go away in favor of using proper tracing points, but
we will see.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add tracing support to log functions

All log messages are now sent through tracing interface as well if
ATH6KL_TRACING is enabled.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: convert ath6kl_info/err/warn macros to real functions

After this it's cleaner to add trace calls.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: adding tracing points for htc_mbox

Add tracing points for htc layer, just dumping the packets to user space.
I wasn't really sure what to do with the status value, it might not always
be accurate, but I included it anyway.

I skipped htc_pipe (and usb) implementation for now. Need to add those
tracepoints later.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add tracing point for hif irqs

Add a tracing point for hif irq and dump the register content to user space.
This is in hif.c as we could use the same code also with SPI but, as ath6kl
doesn't SPI and most likely never will be, this is used just by SDIO so
name the trace point as ath6kl_sdio_irq to make it easier to manage filters.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add tracing points for sdio transfers

Add tracing points for sdio transfers, just dump the address, flags and the
buffer.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add tracing support and tracing points for wmi packets

Add basic tracing infrastructure support to ath6kl and which can be
enabled with CONFIG_ATH6KL_TRACING.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: cold reset target after host warm boot

Julien reported that ar6004 usb device fails to initialise
after host has been rebooted and power is still on for the ar6004 device. He
found out that doing a cold reset fixes the issue.

I wasn't sure what would be the best way to detect if target needs a reset so I
settled on checking a timeout from htc_wait_recv_ctrl_message().

Reported-by: Julien Massot <jmassot@aldebaran-robotics.com>
Tested-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: fix usb related error handling and warnings

It was annoying to debug usb warm reboot initialisation problems as many usb
related functions just ignored errors and it wasn't obvious from the kernel
logs what was failing. Fix all that so that error messages are printed and
errors are handled properly.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: cleanup ath6kl_reset_device()

Move it to init.c, make it static, remove all useless checks and force it to
always do cold reset.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: print firmware capabilities

Printin the  firmware capabilities during the first firmware boot makes it easier to find out what
features firmware supports.

Obligatory screenshot:

[21025.678481] ath6kl: ar6003 hw 2.1.1 sdio fw 3.2.0.144 api 3
[21025.678667] ath6kl: firmware supports: sched-scan,sta-p2pdev-duplex,rsn-cap-override

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

b43: HT-PHY: enable basic TX power setup

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: setup TX power control

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement RSSI polling

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement playing sample tone

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement stopping sample tone playback

It was another sequence I recognized in HT-PHY dump:
 phy_read(0x00c7) -> 0x0001
 phy_read(0x00c3) -> 0x0000
phy_write(0x00c3) <- 0x0002
 phy_read(0x00c3) -> 0x0000
phy_write(0x00c3) <- 0x0000
The difference to N-PHY is that it writes to 6 tables instead of a one
(after above).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement controlling TX power control

Don't enable it until we have (almost?) whole TX power management
figured out. It's similar to the N-PHY, the difference is that we call a
"fix" *before* disabling power control.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement PA override

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement CCA reset

It was just another similar-to-N-PHY and easy-to-track routine:
write32 0xb0601408 <- 0x00002057
 phy_read(0x0001) -> 0x0000
phy_write(0x0001) <- 0x4000
phy_write(0x0001) <- 0x0000
write32 0xb0601408 <- 0x00002055
(b43_phy_ht_force_rf_sequence was moved up unmodified)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement MAC reclocking

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement spurious tone avoidance

On N-PHY it's also done after TX power fix, so it was easy to spot.
Unfortunately the MMIO logs I have from ndsiwrapper include channels
1-12 only, so enabling code for 13 and 14 is just a N-PHY-based guess.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: move TX fix to the separated function

On N-PHY after B43_PHY_B_TEST operation there is a call to TX power fix
function which iterates over available cores. It matches our HT-PHY code
which means it's probably also some TX fix.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: add classifier control function

After comparing operations on reg 0xB on N and HT it seems to be the
same register with similar ops. Implement them for HT-PHY.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: rename AFE defines

It you take a look at N-PHY analog switch function it touches every core
on the chipset. It seems HT-PHY does they same, it just has 3 cores
instead of 2 (which make sense since BCM4331 is 3x3). Rename AFE defines
to include core id.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: temperature measurement

Firmware got support for temperature measurement.
There are 2 temperature sensors: MAC and radio

"not available" temperature - reported by FW as 0 or ~0

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: sync with new firmware

Adjust driver for changes in the FW API.
Noticeable changes in the FW are:
- temperature sensing
- infrastructure for multiple connections
- infrastructure for P2P
- signal strength indication

This commit introduces only changes that are required to support same functionality
as previous firmware, no new features.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: new SW reset

New firmware allows for shorter SW reset procedure.
After SW reset, FW raises "fw done" IRQ, at this
moment mailbox control structures are initialized, driver caches it.

New status bit wil_status_reset_done introduced to track completion
of the reset. It is set by "fw ready" irq, and required for WMI rx flow
to access control structures.

WMI Tx flow protected by other status bit, wil_status_fwready. It can't
be set before wil_status_reset_done is set by design.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: headers clean-up

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: use WLAN_CAPABILITY_DMG_TYPE_MASK

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: fix FW error notification

user space get notified through kobject_uevent_env(), that might sleep and thus
should run in thread context.

Move user space notification to the thread handler, while mark FW is non-functional
right in the hard IRQ.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: report all received mgmt frames

Pass to cfg80211 all management frames.
Used by wpa_supplicant.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: use cfg80211_inform_bss_frame()

Avoid unnecessary frame parsing

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: refactor connect_worker

Move wmi_connect_worker() to the main.c and change names for consistency.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Fix garbage sent to the FW with wmi_set_ie()

Extra reference was taken by mistake.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: do not set IE's for beacon

On the DMG band, there is no 'normal' beacon frame.
Instead, transmitted is short 'DMG beacon' frame, that do not include IE's
So, beacon IE's are not relevant for the DMG band.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: handle WMI_BA_STATUS_EVENTID

Firmware indicated block ack agreement status change.
For now, just log it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: handle linkup/linkdown WMI events

Firmware indicates linkup/linkdown when data path becomes ready.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Remove local implementation of dynamic hexdump

This functionality now integrated in kernel, local hack not needed any more

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: remove unused including <linux/version.h>

Remove including <linux/version.h> that don't need it.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: pci: Fix flipping of MAC address

Since commit e565275 entitled "ssb: pci: Standardize a function to get mac
address", the SPROM readout of the MAC has had the values flipped so that
00:11:22:33:44:55 became 11:00:33:22:55:44. The fix has been tested on both
little- and big-endian architectures.

Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Fix problem that prevents reassociation

The driver was failing to clear the BSSID when a disconnect happened. That
prevented a reconnection. This problem is reported at
https://bugzilla.redhat.com/show_bug.cgi?id=789605,
https://bugzilla.redhat.com/show_bug.cgi?id=866786,
https://bugzilla.redhat.com/show_bug.cgi?id=906734, and
https://bugzilla.kernel.org/show_bug.cgi?id=46171.

Thanks to Jussi Kivilinna for making the critical observation
that led to the solution.

Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: fix rt2x00 to work with the new ralink SoC config symbols

Since v3.9-rc1 the kernel has basic support for Ralink WiSoC. The config symbols
are named slightly different than before. Fix the rt2x00 to match the new
symbols.

The commit causing this breakage is:
commit ae2b5bb6570481b50a7175c64176b82da0a81836
Author: John Crispin <blogic@openwrt.org>
Date:   Sun Jan 20 22:05:30 2013 +0100
MIPS: ralink: adds Kbuild files

Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth

Bluetooth: Device 0cf3:3008 should map AR 3012

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3008 Rev= 0.01
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

mwl8k: don't overwrite regulatory settings on fw reload

Currently the caps are parsed on every firmware reload, causing any
channel flags to be cleared.
When there is a firmware to interface mode mismatch, the triggered
firmware reload causes a reset of the regulatory settings, causing all
channels to become available:

root@openrouter:/# iw phy phy0 info
Wiphy phy0
        Band 1:
(...)
                Frequencies:
                        * 2412 MHz [1] (0.0 dBm)
                        * 2417 MHz [2] (0.0 dBm)
                        * 2422 MHz [3] (0.0 dBm)
                        * 2427 MHz [4] (0.0 dBm)
                        * 2432 MHz [5] (0.0 dBm)
                        * 2437 MHz [6] (0.0 dBm)
                        * 2442 MHz [7] (0.0 dBm)
                        * 2447 MHz [8] (0.0 dBm)
                        * 2452 MHz [9] (0.0 dBm)
                        * 2457 MHz [10] (0.0 dBm)
                        * 2462 MHz [11] (0.0 dBm)
                        * 2467 MHz [12] (0.0 dBm)
                        * 2472 MHz [13] (0.0 dBm)
                        * 2484 MHz [14] (0.0 dBm)
(...)

To prevent this, only parse the caps on the first firmware load during
hardware probe, and store them locally to know we have already parsed
them.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless:rtlwifi: replaced kmalloc+memcpy with kmemdup

Signed-off-by: Andrei Epure <epure.andrei@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: fix sparse warnings

Make local functions and tables static. Make ops table
Mark 3945 ops as read_mostly.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco_usb: don't release nonexistent firmware

Initialize fw_entry to NULL to prevent cleanup code from passing
bogus pointer to release_firmware() when priv allocation fails.

Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'nfc-next-3.10-1' of git://git./linux/kernel/git/sameo/nfc-next

Samuel Ortiz <sameo@linux.intel.com> says:

This is the first NFC pull request for 3.10.

The 2 features we have with this one are:

- An LLCP Service Name Lookup (SNL) netlink interface for querying LLCP
  service availability from user space.
  Along the way, Thierry also improved the existing SNL interface for
  aggregating SNL responses.

- An initial LLCP socket options implementation, for setting the Receive
  Window (RW) and the Maximum Information Unit Extension (MIUX) per socket.
  This is need for the LLCP validation tests.

We also have a microread MEI build failure here: I am not sending this one to
3.9 because the MEI bus code is not there yet, so it won't break for anyone
else than me.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'nfc-fixes-3.9-1' of git://git./linux/kernel/git/sameo/nfc-fixes

Samuel Ortiz <sameo@linux.intel.com> says:

This is the first NFC pull request for 3.9 fixes

With this one we have:

- A fix for properly decreasing socket ack log.
- A timer and works cleanup upon NFC device removal.
- A monitoroing socket cleanup round from llcp_socket_release.
- A proper error report to pending sockets upon NFC device removal.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: llcp: Add cleanup support for unreplied SNL requests

If the remote LLC doesn't reply in time to our SNL requests we remove
them from the list of pending requests. The timeout is fixed to an
arbitrary value of 3 times remote_lto.

When not replied, the local LLC broadcasts NFC_EVENT_LLC_SDRES nl events for
the concerned uris with sap values set to LLCP_SDP_UNBOUND (which is 65).

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Service Name Lookup netlink interface

This adds a netlink interface for service name lookup support.
Multiple URIs can be passed nested into the NFC_ATTR_LLC_SDP attribute
using the NFC_CMD_LLC_SDREQ netlink command.
When the SNL reply is received, a NFC_EVENT_LLC_SDRES event is sent to
the user space. URI and SAP tuples are passed back, nested into
NFC_ATTR_LLC_SDP attribute.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Service Name Lookup SDRES aggregation

This modifies the way SDRES PDUs are sent back. If multiple SDREQs are
received within a single SNL PDU, all SDRES replies are sent packed in
one SNL PDU too.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: Add missing type policies for netlink attributes

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Remove redundant printk

We already have a pr_debug for that.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Use socket specific link parameters before the local ones

If the socket link options are set, use them before the local one.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Implement socket options

Some LLCP services (e.g. the validation ones) require some control over
the LLCP link parameters like the receive window (RW) or the MIU extension
(MIUX). This can only be done through socket options.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Rename socket rw and miu fields

They really are remote peer parameters, and we need to distinguish them
from the local ones as we'll modify the latter with socket options.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: microread: Fix MEI build failure

The mei_device field should be called device, not mei_device.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

ath6kl: small cleanup in ath6kl_htc_pipe_rx_complete()

It's harmless, but Smatch complains if we use "htc_hdr->eid" before
doing the bounds check.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

mwifiex: fix potential null dereference 'mef_entry'

drivers/net/wireless/mwifiex/cfg80211.c:2357 mwifiex_cfg80211_suspend()
  error: potential null dereference 'mef_entry'
  (kzalloc returns null)

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: Trigger a card reset on reaching tx_timeout threshold

tx_timeout doesn't always lead to a cmd_timeout. There are
occurrences where cmd_timeout never gets triggered for a long
time and we encounter a kernel crash. In this patch, we track
the consecutive timeouts (tx_timeout_cnt). When tx_timeout_cnt
exceeds the threshold, trigger a card reset thereby avoiding a
kernel crash.

Signed-off-by: Ashok Nagarajan <asnagarajan@chromium.org>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: update email address

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Fix schedule while atomic bug splat

When run at debug 3 or higher, rtl8192cu reports a BUG as follows:

BUG: scheduling while atomic: kworker/u:0/5281/0x00000002
INFO: lockdep is turned off.
Modules linked in: rtl8192cu rtl8192c_common rtlwifi fuse af_packet bnep bluetooth b43 mac80211 cfg80211 ipv6 snd_hda_codec_conexant kvm_amd k
vm snd_hda_intel snd_hda_codec bcma rng_core snd_pcm ssb mmc_core snd_seq snd_timer snd_seq_device snd i2c_nforce2 sr_mod pcmcia forcedeth i2c_core soundcore
 cdrom sg serio_raw k8temp hwmon joydev ac battery pcmcia_core snd_page_alloc video button wmi autofs4 ext4 mbcache jbd2 crc16 thermal processor scsi_dh_alua
 scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic pata_acpi pata_amd [last unloaded: rtlwifi]
Pid: 5281, comm: kworker/u:0 Tainted: G        W    3.8.0-wl+ #119
Call Trace:
 [<ffffffff814531e7>] __schedule_bug+0x62/0x70
 [<ffffffff81459af0>] __schedule+0x730/0xa30
 [<ffffffff81326e49>] ? usb_hcd_link_urb_to_ep+0x19/0xa0
 [<ffffffff8145a0d4>] schedule+0x24/0x70
 [<ffffffff814575ec>] schedule_timeout+0x18c/0x2f0
 [<ffffffff81459ec0>] ? wait_for_common+0x40/0x180
 [<ffffffff8133f461>] ? ehci_urb_enqueue+0xf1/0xee0
 [<ffffffff810a579d>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff81459f65>] wait_for_common+0xe5/0x180
 [<ffffffff8107d1c0>] ? try_to_wake_up+0x2d0/0x2d0
 [<ffffffff8145a08e>] wait_for_completion_timeout+0xe/0x10
 [<ffffffff8132ab1c>] usb_start_wait_urb+0x8c/0x100
 [<ffffffff8132adf9>] usb_control_msg+0xd9/0x130
 [<ffffffffa057dd8d>] _usb_read_sync+0xcd/0x140 [rtlwifi]
 [<ffffffffa057de0e>] _usb_read32_sync+0xe/0x10 [rtlwifi]
 [<ffffffffa04b0555>] rtl92cu_update_hal_rate_table+0x1a5/0x1f0 [rtl8192cu]

The cause is a synchronous read from routine rtl92cu_update_hal_rate_table().
The resulting output is not critical, thus the debug statement is
deleted.

Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

mwifiex: fix potential out-of-boundary access to ibss rate table

smatch found this error:

CHECK   drivers/net/wireless/mwifiex/join.c
  drivers/net/wireless/mwifiex/join.c:1121
  mwifiex_cmd_802_11_ad_hoc_join()
  error: testing array offset 'i' after use.

Cc: <stable@vger.kernel.org> # 3.0+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: llcp: Report error to pending sockets when a device is removed

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Clean raw sockets from nfc_llcp_socket_release

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Clean local timers and works when removing a device

Whenever an adapter is removed we must clean all the local structures,
especially the timers and scheduled work. Otherwise those asynchronous
threads will eventually try to access the freed nfc_dev pointer if an LLCP
link is up.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: llcp: Decrease socket ack log when accepting a connection

This is really difficult to test with real NFC devices, but without
this fix an LLCP server will eventually refuse new connections.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mwifiex: add WOWLAN support

Currently 'magic-packet' and 'patterns' options in 'iw wowlan'
command are supported.

Appropriate packet filters for wowlan are configured in firmware
based on provided patterns and/or magic-packet option.

For examples,

wake-on ARP request for 192.168.0.100:
iw phy0 wowlan enable patterns ff:ff:ff:ff:ff:ff 20+08:06
  46+c0:a8:00:64

wake-on RX packets sent from IP address 192.168.0.88:
iw phy0 wowlan enable patterns 34+c0:a8:00:58

wake-on RX packets with TCP destination port 80
iw phy0 wowlan enable patterns 44+50

wake-on MagicPacket:
iw phy0 wowlan enable magic-packet

wake-on MagicPacket or patterns:
iw phy0 wowlan enable magic-packet patterns 12+00:11:22:33:44:55
  18+00:50:43:21

wake-on IPv4 multicast packets:
iw phy0 wowlan enable patterns 01:00:5e

wake-on IPv6 multicast packets:
iw phy0 wowlan enable patterns 33:33

disable all wowlan options
iw phy0 wowlan disable

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>