cfg80211: change function signature of cfg80211_get_p2p_attr()

The function cfg80211_get_p2p_attr() can fail and returns
a negative error code. However, the return type is unsigned
int. The largest positive number is determined by desired_len
variable in the function, which is u16. So changing the return
type to int to allow easy error checking. Also change the type
for the attribute to enum for improved type checking.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
[fix indentation, don't use u8 attr variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: use DS or HT operation IEs to determine BSS channel

Currently, mac80211 checks the DS params IE if present and
uses it for the (primary) BSS channel, instead of the one
that the frame was received on. This is particularly useful
in the 2.4 GHz band since a frame is often received on one
of the adjacent channels due to overlap.

Move this code to cfg80211 so other drivers also do this.

Additionally, on 5 GHz, in particular with some (possibly)
upcoming changes in 802.11ai and duplicate transmissions
when wider channels are used, something similar happens.
So if present, also use the (primary) channel information
contained in the HT operation IE.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: disable HT advertising unless AP supports it

If the AP doesn't support HT, or more importantly if
it does but we have to disable it because its IEs are
broken, don't advertise HT support in our association
request. Otherwise, we configure our channel to be a
20 MHz non-HT channel but the AP might still think we
support HT, or even 40 MHz.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: rename IEEE80211_STA_DISABLE_11N to HT

Since the 11n spec amendment was rolled into the
2012 version, "11n" no longer makes sense. Use
"HT" instead.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix RX chains configuration

If the driver doesn't support 40 MHz channels, then
mac80211 erroneously sets number of RX chains to one
although the number of chains is independent of the
support for 40 MHz channels.

Fix this by checking the 40 MHz support only for the
code that sets the 40 MHz channel not the complete
HT code block.

This also means the HT20 channel type will always be
set in the changed code block so there's no need to
set it in case we override the AP due to invalid IEs
in the probe response/beacon.

The indentation is a bit quirky, but I'm rewriting
this code for VHT support so this will change again
very soon.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix radiotap vendor area skipping

The radiotap vendor area in the skb head must be skipped
and accounted for in a few functions until it is removed.
I missed this in my patch, so a few places use this data
as though it was the 802.11 header, fix these places.

Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: Add debugfs callbacks for station addition/removal

Provide drivers with hooks to create debugfs files when
a new station is added. This would help drivers to take
advantage of mac80211's station list infrastructure and not maintain
tedious station management code internally.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[ifdef inline wrapper functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix channel context suspend/reconfig handling

Sujith reported warnings with suspend/resume due to
channel contexts. When I looked into it, I realised
that the code was completely broken as it unassigned
the channel contexts when suspending, which actually
means they are destroyed.

Eliad Peller then pointed out that we also need to
remove the channel contexts from the driver. When I
looked into this, I also noticed that the code isn't
handling the virtual monitor interface correctly (if
it exists.)

Fix this by calling just the driver methods (if they
are implemented) instead of using the channel context
management code. Also add reconfiguration for the
virtual monitor interface.

Reported-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: make remain_on_channel() op pass vif param

Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).

Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.

Signed-off-by: Eliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Add TDLS event to allow drivers to request operations

The NL80211_CMD_TDLS_OPER command was previously used only for userspace
request for the kernel code to perform TDLS operations. However, there
are also cases where the driver may need to request operations from
userspace, e.g., when using security on the AP path. Add a new cfg80211
function for generating a TDLS operation event for drivers to request a
new link to be set up (NL80211_TDLS_SETUP) or an existing link to be
torn down (NL80211_TDLS_TEARDOWN). Drivers can optionally use these
events, e.g., based on noticing data traffic being sent to a peer
station that is seen with good signal strength.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: support radiotap vendor namespace RX data

In some cases, in particular for experimentation, it
can be useful to be able to add vendor namespace data
to received frames in addition to the normal radiotap
data.

Allow doing this through mac80211 by adding fields to
the RX status descriptor that describe the data while
the data itself is prepended to the frame.

Also add some example code to hwsim, but don't enable
it because it doesn't use a proper OUI identifier.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: introduce IEEE80211_NUM_TIDS and use it

Introduce IEEE80211_NUM_TIDS in the generic 802.11
header file and use it in place of STA_TID_NUM and
NUM_RX_DATA_QUEUES which are both really the number
of TIDs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: use CMAC_PN_LEN

Instead of hardcoding its value (6), use the constant.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: check add_chanctx callback before use in ieee80211_reconfig

During testing our mac80211 driver a fatal error occurred which was
signalled to mac80211. Upon performing the reconfiguration of the
device a WARN_ON was triggered. This warning checked the return value
of drv_add_chanctx(). However, this returns -EOPNOTSUPP when the
driver does not provide the callback. As the callback is optional
better check it is defined before calling drv_add_chanctx().

Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: support RX_FLAG_MACTIME_END

Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl/cfg80211: advertise OBSS scan requirement

wpa_supplicant will do OBSS scan for drivers that implement
auth/assoc API. Drivers that implement nl80211 connect API
(rather than auth/assoc) may need wpa_supplicant to do this
as well.

Add a new feature flag to inform it (wpa_s) that a driver
needs wpa_supplicant to do OBSS scans.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: reassign channel contexts before stations

Since channel contexts are usually present before
stations can be added to an interface, reassign
before stations them in reconfiguration as well.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: clarify interface iteration and make it configurable

During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.

Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: call driver method when restart completes

When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove unused tracepoint

Clearly the tracepoint drv_offchannel_tx was
forgotten when that functionality was removed,
remove it now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: add debugfs file for HW queues

Add a debugfs file showing which HW queues were
allocated to a virtual interface, including the
CAB queue for AP interfaces.

Change-Id: I486924e961b6ad6785a79db09620919ee644e703
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix TX error path

One error path in ieee80211_subif_start_xmit() will
double-free the SKB. Set it to NULL to prevent that.

This issue was introduced by my channel context
changes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: include export.h in aes_cmac

This is needed since this file exports functions.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: use kstrtoull return value

If kstrtoull() returns an error code (a value
smaller than zero), use it since it can be an
error other than -EINVAL.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix race in TKIP MIC test debugfs file

Accessing sdata->vif.bss_conf.bssid without any
protection here is racy, use u.mgd.associated
instead and lock the correct mutex for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: use mac_pton

Instead of implementing practically the same
function (hwaddr_aton) use mac_pton.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: send the NL80211_ATTR_SSID in nl80211_send_iface()

The userspace may want to know what is the current ssid that a given
interface is using. This patch enables nl80211 to send the
NL80211_ATTR_SSID attribute in nl80211_send_iface().

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: store the ssid into wirless_dev in AP mode

Store the configured ssid in wdev->ssid when starting an AP

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: pass P2P powersave parameters to driver

While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: add utility function to get P2P attribute

Parsing the P2P attributes can be tricky as their
contents can be split across multiple (vendor) IEs.
Thus, it's not possible to parse them like IEs (by
returning a pointer to the data.) Instead, provide
a function that copies the attribute data into a
caller-provided buffer and returns the size needed
(useful in case the buffer was too small.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: allow registering more than one beacon listener

The commit:

commit 5e760230e42cf759bd923457ca2753aacf2e656e
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Nov 4 11:18:17 2011 +0100

    cfg80211: allow registering to beacons

allowed only a single process to register for beacon events
per wiphy.  This breaks cases where a user may want two or
more VIFs on a wiphy and run a seperate hostapd process on
each vif.

This patch allows multiple beacon listeners, fixing the
regression.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: implement set_mcast_rate() callback

This new callback can be used to tune the rate to be used to send
multicast frames.

In the current state the multicast rate can be specified on IBSS/MESH
joining only. This makes it impossible to select a custom multicast
rate when then join command is sent by an external program (e.g.
wpa_supplicant)

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl/cfg80211: add the NL80211_CMD_SET_MCAST_RATE command

This command triggers a new callback: set_mcast_rate(). It enables
the user to change the rate used to send multicast frames for vif
configured as IBSS or MESH_POINT

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: add peer-to-peer related definitions

The Peer-to-Peer IE is vendor-specific IE identified by WiFi Alliance
OUI and specific P2P OUI type. The payload of this IE consists of
so-called P2P attributes. This patch adds definitions for processing
these attributes.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: send deauth only with channel context

When userspace asks to deauthenticate and we're just
authenticated (or still authenticating) send a deauth
frame instead of deleting the auth request.

On the other hand, if we've just disassociated and
therefore deleted all our state already, drop the
deauth request because we no longer have a channel
context to send it on.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: use a counter for remain-on-channel cookie

Instead of using the pointer which can be re-used
fairly quickly due to allocator patterns and then
makes debugging difficult, maintain a counter and
use its value. Since it's a 64-bit value it can't
really wrap, but catch that case anyway since it
most likely points to a bug somewhere.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: combine status/drop reporting

The TX status reporting is done for both the
nl80211 report as well as the socket option.
The socket option is also reported when an
skb is dropped to guarantee that the copy in
the IDR tree is freed and status is reported
to userspace.

However, when a frame is dropped, no nl80211
status is reported. This can cause userspace
to stop making progress while waiting for a
status notification.

Combine the nl80211 and socket option status
reporting into a new function and call it in
both places -- when the status comes in from
the driver and when the skb is dropped.

While at it, also simplify the code in the
nl80211 portion a bit.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: print per interface TX power

Just for debugging, print the interface TX
power whenever it changes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: handle TX power per virtual interface

Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.

Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: allow per interface TX power setting

The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: move "can set channel" check

Setting the wdev to NULL when the channel can't be
set for that interface type (to treat the channel
setting for the wiphy/monitor) currently works, but
is confusing in the code if netdev/wdev aren't both
set/unset in the same way. Move the check whether
the channel can be set to where it's needed so that
wdev and netdev are always both assigned or NULL.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: allow using channel contexts

To use mac80211_hwsim for testing channel contexts it
has to support them, and for that it has to support
hw scan and hw-remain-on-channel.

Since it's pure software, the off-channel activities
are really not off-channel but listening and sending
on a second channel. Also, the multi-channel isn't
really doing TDM, it's just on both channels at the
same time.

For testing purposes, you can specify the number of
concurrent channels with a module parameter, it is
set to one by default. When set to two or more, the
userspace API for wmediumd is disabled as it has no
provisions for multi-channel yet.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge remote-tracking branch 'wireless-next/master' into mac80211-next

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
drivers/net/wireless/mwifiex/cfg80211.c

ssb: handle BCM43222 in pmu code.

The BCM43222 with the chipid 43222 or 0xa8d6 in hex do not need any
special handling in the pmu code. This prevents some error messages
being shown.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: add PCI ID 0x4350

14e4:4350 is found on a Broadcom BCM43222.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Dump BTCOEX tuning parameters

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: validate MCI stuck after RTC wakeup

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix concurrent tx on lower tx power

Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable hw PLL power save for AR9565

This reduced the power consumption to half in full and network sleep.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable hw PLL power save for AR9462

This reduced the power consumption to half in full and network sleep.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar5523: Add new driver

This driver is for the AR5523 chipset from Atheros. It was created
in 2007 by Christoph Hellwig but it was never finished. I found it a
couple of months ago and after some polishing it's working pretty
fine.

The driver was written with the FreeBSD driver (uath) as reference,
which was written with the reverse-engineered windows driver as
reference, hence the feature set is very limited. Station mode
only, no HW crypto offload.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: store IEs per virtual interface

For AP feature the IEs are stored in global structure. For future
functionality like P2P-GO it needs to be stored per virtual interface
so better store it in the virtual interface structure.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unnecessary macro usage in brcmf_cfg80211_resume()

The macro wiphy_to_cfg() is a bit redundant as the function already
has a pointer variable to brcmf_cfg80211_info structure.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add virtual interface support in brcmf_cfg80211_suspend()

With multiple interfaces suspend will need to iterate over all and
bring down the link.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use memset when setting a broadcast mac address

The driver had a global constant ether_bcast, which was copied
whenever a broadcast mac address was needed. This patch does a
memset(dest, 0xFF, ETH_ALEN) instead and consequently removes
the global ether_bcast.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: rename check_sys_up() to check_vif_up()

The function now return the status for a virtual interface so
it seems better rename the function to understand what it does.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unused enumeration wl_prof_list

The enumeration wl_prof_list is no longer used so it can be safely
removed.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: cleanup brcmf_cfg80211_profile structure

A couple of unused fields have been removed and kernel-doc info has
been added to the structure.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove debugfs functionality from wl_cfg80211.c

In wl_cfg80211.c debugfs directory was created to expose
dtim_period and beacon_interval. However, this can be easily
obtained using iw so it is removed from the driver.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: separate connection status from scanning status

The connection status is to be kept per virtual interface and
the scanning status is for device. So they need to be separated
for multiple interface support.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use vif struct to check_sys_up() function

This checks the status that will soon be moved to virtual
interface data so preparing for that use the structure
brcmf_cfg80211_vif as parameter instead.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meulemen <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: store profile information per virtual interface

The profile information applies to an interface so each virtual
interface needs it. So it is removed from brcmf_cfg80211_info
and added to brcmf_cfg80211_vif structure.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: introduce brcmf_cfg80211_vif structure

This patch introduces the brcmf_cfg80211_vif structure which is
used to keep track of multiple virtual interfaces in the driver.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove brcmf_find_bssidx() function

The function brcmf_find_bssidx() is no longer used so remove
it from the driver code.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: change parameter list for send_key_to_dongle()

The first two parameters given to send_key_to_dongle() are redundant
so they have been removed.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use fwil for default configuration setup.

modify the setup code to use the refactored firmware interface layer.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: streamline header parse code of sdio glom read

Use brcmf_sdio_hdparser to handle header of super frame and sub
frame in glomming frame read.

Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use struct brcmf_if as interface object for fwil functions

The functions for communicating were given the net_device only because
its private data contained struct brcmf_if object. However, not all
firmware related interfaces will be associated with a net_device. To
accomodate provisioning firmware for such interfaces the struct
brcmf_if object will be passed to the fwil functions.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add function converting ieee80211_channel to chanspec

The firmware carries channel information in a different format
as the provided ieee80211_channel structure. Conversion is needed
when receiving requests from cfg80211 carrying ieee80211_channel
structures. This patch adds a utility function to do that.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use bssidx from struct brcmf_if for bsscfg specific commands

The firmware interface has functions to send bsscfg specific commands
to the device. These functions currently have a bssidx parameter, but
that same information is stored in struct brcmf_if, which is in the
private data of the net_device parameter.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: rework driver initialization in brcmf_bus_start()

In brcmf_bus_start() a number of settings are sent to the device. For
this functions are used that bypass the common firmware interface.
By reordering the code in brcmf_bus_start() this bypass can be removed.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: extend struct brcmf_if with bssidx field

When the firmware notifies the driver about adding a new interface
it also provides an index for the bss associated with this interface.
This index will be needed for upcoming features like peer-to-peer.
By adding this index in struct brcmf_if it is easy to obtain as this
will be associated with the net_device private data.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: clean usb download code.

reuse ioctl waiting method.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove redundant function brcmf_c_mkiovar_bsscfg

function brcmf_c_mkiovar_bsscfg became redundant with refactoring
of firmware interface layer.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: change testmode command to use new firmware interface layer

switch to new firmware interface layer and remove redundant code.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unused iswl variable.

Variable iswl always gets initialised to the same and support for
this var is not needed.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: refactor firmware interface layer.

Refactor the functions that are related to getting and setting
data to and and from the firmware.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: split up carl9170_handle_mpdu

carl9170_handle_mpdu is the final part of the
rx path of the driver. It splits the raw data
streams from the device into skb packets and
passes them on to mac80211. As a result of
continuous updates, it grew over the years when
new code was added by the following commits:
- report A-MPDU status
- fix HT peer BA session corruption
- A-MPDU frame type filter
- ...

This patch splits the routine into two stages.
The first stage only deals with the details
about extracting and verifying the data from
the incoming stream. Whereas the second stage
packs it into skbs and passes it on to mac80211.

Reported-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: rx path enhancement to derive priv only once

We derive mwifiex_private structure which is per interface from
received skb's rx_info. Once priv is derived, same priv can be
propagated to other functions instead of callee deriving priv
from rx_info again.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: handle extended supported rates IE for AP

During start_ap handler, some rates come as extended supported
rates IE - part of beacon tail IE. This patch adds support for
parsing them and adding to bss_rates TLV for bss_start command
to firmware.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "mwifiex: retrieve correct max_power information in reg_notifier handler"

This reverts commit 34202e28fe7fc8551313f9a035a8857db83de757

We made "34202ee.." because we didn't support custom regulatory rules
at that time. But now we use our own custom regulatory rules, so it
needs to be changed back.

Also, chan->max_power calculations in cfg80211 were broken. Hence we
started using chan->max_reg_power. Now it has got fixed in
following commit.

commit 5e31fc0815a4e2c72b1b495fe7a0d8f9bfb9e4b4
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Tue Jul 24 08:35:39 2012 +0200

    wireless: reg: restore previous behaviour of chan->max_power calculations

Hence we will use chan->max_power instead of chan->max_reg_power.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: disable channel filtering for SSID specific scan from user

If MWIFIEX_DISABLE_CHAN_FILT bit in scan mode bitmap is set,
firmware will turn off the filtering of scan responses from
adjacent channels.

Currently the bit is set only for internal SSID specific scan
performed during association. We will set it for user requested
SSID specific scan as well.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: minor cleanup and a fix in scan semaphore usage

mwifiex_request_scan() takes care of synchronous internal scan
performed by driver during association.
Currently the semaphore acquired for the scan is unnecessarily
released at the end of different paths. Also, failure paths
returning error code other than "-1" are not considered.

We will release it at the end of routine to fix above issues.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: abort scan upon interface down

When the interface is down, we will abort scan by calling
cfg80211_scan_done() with abort option. This fixes WARN_ON
triggered by cfg80211 in wdev_cleanup_work().

Driver's internal variables/flags are cleared once we get
response for current scan command. Meanwhile we will block
new scan request from cfg80211.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use LOW_PRIORITY scan flag provided in scan request

We will delay/abort scan operation based on traffic for low
priority scan.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: suspend/resume callbacks should be conditionally compiled on CONFIG_PM_SLEEP

This will fix warnings like following when CONFIG_PM_SLEEP is not set:

        warning: 'xxx_suspend' defined but not used [-Wunused-function]
        warning: 'xxx_resume' defined but not used [-Wunused-function]

Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)

Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).

Cc: John W. Linville <linville@tuxdriver.com>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add new BT profile info A2DP_Voice

When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: adjust duty cycle for FTP profile for AR9565

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Set default MCI config for AR9565

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure new switch table for AR9565 BTCOEX

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix max rx rate drop for AR9565

Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix frequent BT rx recovery

While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Disable MCI stat counter by default for AR9565

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: turn off RXIQ calibration while re-calibrating radio

TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Set appropriate bit for AR9565 in btc control register

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix selfgen chainmask for 9565

Self generated MCI messages is configured to use chain 1. As
ar9565 is 1x1 solution, It can not use Chain 1. Hence fix
Chain 1 for ar9462 alone. Not doing so, could affect WLAN
connectivity in ar9565 as LNA sharing is not informed by BT.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable OSLA hw fix for AR9565

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: adjust WLAN and BT concurrent transmission

The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fill channel mode in caldata

It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>