net: revert "sched classifier: make cgroup table local"

This reverts commit de6fb288b1246a5c4e00c0cdbfe3a838a360b3f4.
Otherwise we got:

net/sched/cls_cgroup.c:106:29: error: static declaration of ‘net_cls_subsys’ follows non-static declaration
 static struct cgroup_subsys net_cls_subsys = {
                             ^
In file included from include/linux/cgroup.h:654:0,
                 from net/sched/cls_cgroup.c:18:
include/linux/cgroup_subsys.h:35:29: note: previous declaration of ‘net_cls_subsys’ was here
 SUBSYS(net_cls)
                             ^
make[2]: *** [net/sched/cls_cgroup.o] Error 1

Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sched classifier: make cgroup table local

Doesn't need to be global.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sched action: make local function static

No need to export functions only used in one file.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en: Only cycle port if HW timestamp config changes

If the hwtstamp_config matches what is currently set for the device then
simply return.  Without this change any program that tries to enable
hardware timestamps will cause the link to cycle even if hardware
timstamps were already enabled.

Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Acked-By: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en: Add PTP hardware clock

This adds a PHC to the mlx4_en driver. We use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled.  This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.

This driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-3 card.

Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Acked-By: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: switch and case should be at the same indent

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: spaces required around that '='

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Cleanup in eth-netx.h

Commit 2960ed346877 ("ARM: netx: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

hamradio: 6pack: fix error return code

Set the return variable to an error code as done elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix error return code

Set the return variable to propagate any error code as done elsewhere in
the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: remove prune parameter for fib6_clean_all

since the prune parameter for fib6_clean_all always is 0, remove it.

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: make the code look more readable

In commit 3b8401fe9d ("tipc: kill unnecessary goto's") didn't make
the code look most readable, so fix it. This patch is cosmetic
and does not change the operation of TIPC in any way.

Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tun, rfs: fix the incorrect hash value

The code incorrectly save the queue index as the hash, so this patch
is fixing it with the hash received in the stack receive path.

Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: arp: update neighbour address when a gratuitous arp is received and arp_accept is set

Gratuitous arp packets are useful in switchover scenarios to update
client arp tables as quickly as possible. Currently, the mac address
of a neighbour is only updated after a locktime period has elapsed
since the last update. In most use cases such delays are unacceptable
for network admins. Moreover, the "updated" field of the neighbour
stucture doesn't record the last time the address of a neighbour
changed but records any change that happens to the neighbour. This is
clearly a bug since locktime uses that field as meaning "addr_updated".
With this observation, I was able to perpetuate a stale address by
sending a stream of gratuitous arp packets spaced less than locktime
apart. With this change the address is updated when a gratuitous arp
is received and the arp_accept sysctl is set.

Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: namespace cleanups

Running 'make namespacecheck' shows:
  net/ipv6/route.o
    ipv6_route_table_template
    rt6_bind_peer
  net/ipv6/icmp.o
    icmpv6_route_lookup
    ipv6_icmp_table_template

This addresses some of those warnings by:
 * make icmpv6_route_lookup static
 * move inline's out of ip6_route.h since only used into route.c
 * move rt6_bind_peer into route.c

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: core functions cleanup

The following functions are not used outside of net/core/dev.c
and should be declared static.

  call_netdevice_notifiers_info
  __dev_remove_offload
  netdev_has_any_upper_dev
  __netdev_adjacent_dev_remove
  __netdev_adjacent_dev_link_lists
  __netdev_adjacent_dev_unlink_lists
  __netdev_adjacent_dev_unlink
  __netdev_adjacent_dev_link_neighbour
  __netdev_adjacent_dev_unlink_neighbour

And the following are never used and should be deleted
  netdev_lower_dev_get_private_rcu
  __netdev_find_adj_rcu

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: cleanup tap related functions

Cleanups in netlink_tap code
 * remove unused function netlink_clear_multicast_users
 * make local function static

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: make more functions static

More functions in bonding that can be declared static because
they are only used in one file.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: cleanup rntl_af_register

The function __rtnl_af_register is never called outside this
code, and the return value is always 0.

Signed-off-by: David S. Miller <davem@davemloft.net>

stmicro: make local variables static

Make variables only used in one file static. Also avoids possible
namespace collisions.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series implements the Linux Virtual Function (VF) driver for
the Intel Ethernet Controller XL710 family.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bonding'

Ding Tianhong says:

====================
bonding: slight optimization for bonding

This serious of patches will slight optimize the mac address compare
and xmit path for bonding, also make some cleanups.

Julia was using ether_addr_equal_64bits to instead of ether_addr_equal,
it is really a hard work and she may did not make patch for bonding yet,
so I have do it in this patchset and that she could miss the bonding drivers.

resend and add cc for Julia.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: use ether_addr_equal_64bits to instead of ether_addr_equal

The net_device.dev_addr have more than 2 bytes of additional data after
the mac addr, so it is safe to use the ether_addr_equal_64bits().

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: remove the return value for bond_3ad_bind_slave()

I'm sure the operand slave and bond for the function will not
be NULL, so the check for the bond will not make any sense, so
remove the judgement, and the return value was useless here,
remove the unwanted return value.

The comments for the bond 3ad is too old, cleanup some errors
and warming.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: remove unwanted return value for bond_dev_queue_xmit()

The return value for bond_dev_queue_xmit() will not be used anymore,
so remove the return value.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: slight optimizztion for bond_slave_override()

When the skb is xmit by the function bond_slave_override(),
it will have duplicate judgement for slave state, and I think it
will consumes a little performance, maybe it is negligible,
so I simplify the function and remove the unwanted judgement.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: slight optimization for bond_alb_xmit()

The bond_alb_xmit will check the return value for
bond_dev_queue_xmit() every time, but the bond_dev_queue_xmit()
is always return 0, it is no need to check the value every time,
so remove the unneed judgement for the xmit path.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: slight optimization for bond_3ad_xmit_xor()

The bond_dev_queue_xmit() will always return 0, and as a fast path,
it is inappropriate to check the res value when xmit every package,
so remove the res check and avoid once judgement for xmit.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: use ether_addr_equal_unaligned for bond addr compare

Use possibly more efficient ether_addr_equal_64bits
to instead of memcmp.

Modify the MAC_ADDR_COMPARE to MAC_ADDR_EQUAL, this looks more
appropriate.

The comments for the bond 3ad is too old, cleanup some errors
and warming.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'r8152'

Hayes Wang says:

====================
support new chip

Remove the trailing "/* CRC */" for patch #3.

Change the return value type of rtl_ops_init() from int to boolean
for patch #4.

Replace VENDOR_ID_SAMSUNG with SAMSUNG_VENDOR_ID for patch #6.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: support RTL8153

Support new chip RTL8153 which is the USB 3.0 giga ethernet adapter.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: split rtl8152_enable

Split the contents of rtl8152_enable() into rtl_set_eee_plus() and
rtl_enable().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: add rtl_ops

The different chips may have different settings. This makes it easy
to let different chips have the same flow with differnt settings.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: change some definitions

Replace RX_BUF_THR with RX_THR_HIGH.
Replace RWSUME_INDICATE with RESUME_INDICATE.
Add CRC_SIZE, TX_ALIGN, and RX_ALIGN.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: modify the method of accessing PHY

The old method to access PHY is through mdio channel. Replace it
with the OCP channel.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: move rtl8152_unload and ocp_reg_write

Change the locations of rtl8152_unload() and ocp_reg_write().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
pull request: wireless-next 2014-01-01

These patches were tucked-in with me for my long winter's nap!
Please pull them for the 3.14 stream...

For the mac80211 bits, Johannes says:

"Here I just have a collection of fixes/improvements/cleanups, very
little really stands out apart from CSA fixes, vendor command support
and the RCU speedups."

For the iwlwifi bits, Emmanuel says:

"I have hear quite a few things. Alex continues his work on power
management. Arik is reworking the transport API by unifying redudant
APIs and making error handling more generic. Eyal keeps on digging in
the rate scaling code.
We also have two new features - Max is using the brand new generic
cipher infrastructure in mac80211, and Lilach implements the smart fifo
which allows to save power by making interrupt coalescing smarter."

Along with those, Arend and company bring a batch of brcmfmac.
Sujith and Felix bring the usual high level of ath9k activity as well.
Bing gives mwifiex some love as well, and a handful of other bits
get updates here and there.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

cnic: Add a signature to indicate valid doorbell offset.

The buffer that is used to pass doorbell offset to the userspace UIO
driver may contain nonzero value in older versions of bnx2x driver.
Userspace cannot easily tell whether it contains a valid doorbell
offset or not.  With the added signature, userspace will only use
the doorbell offset if the signature is present.

Update version to 2.5.19.

Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2: Update version to 2.2.5.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2: Report MDI/MDIX status to ethtool.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2: Enable auto-mdix when autoneg is disabled.

Auto-mdix currently only works if autoneg is enabled.  This patch enables
auto-mdix all the time by setting a bit in a PHY register.  Define
meaningful constants for this PHY registers.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2: Advertise nothing when speed is forced

The current code does not reset the advertisement register when the speed
is forced, leaving the default advertisement value of 10 Mbps.  This does
not work with some link partners when the next patch enables auto-mdix.

Set advertisement register to 0 if the speed is forced.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem

i40evf: A0 silicon specific

A0 stepping silicon specific code

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: add driver to kernel build system

Modify the existing Kconfig, Makefile, and MAINTAINERS to add the driver
to the kernel. Add a Makefile and a documentation

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: init code and hardware support

This patch implements the hardware specific init and management.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: driver core headers

This patch contains the main driver header files, containing structures
and data types specific to the linux driver.

i40e_osdep.h contains some code that helps us adapt our OS agnostic code
to Linux.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: virtual channel interface

This PCI-E SR-IOV virtual function (VF) driver is dependant upon the
physical function (PF) driver (i40e) for nearly all of its hardware
configuration. Requests from the VF driver are passed to the PF using
the hardware's Admin Queue.

This patch contains the functionality for communicating with the PF
driver. Because of the delay inherent in this communications channel,
most of the replies from the PF driver are handled asynchronously. The
exceptions are the "send API version" and "get VF config" messages,
which busy-wait because they are done so early during init that
interrupts are not yet configured.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: core ethtool functionality

This patch contains the ethtool interface and related functionality.
Since the VF driver is mostly unaware of link, much of that
functionality is unused. The driver implements ethtool hooks for
statistics, driver info, and some basic non-link-related driver
settings.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: transmit and receive functionality

This file contains the transmit, receive, and NAPI functionality.

Some of the functions in this module are extracted from the i40e driver
but functions that are not appropriate for virtual function devices have
been removed.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf: main driver core

This is the driver for the Intel(R) XL710 X710 Virtual Function.

This patch contains the main driver entry points, but does not include
transmit and receive or ethtool functionality, which are presented as
separate patches in this series.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge branch 'addr_compare'

Ding Tianhong says:

====================
slight optimization of addr compare for net modules

This is the second patchset for slight optimization of address compare,
mainly for net tree, just following the Joe's opinion, it will help review
the code for maintainers and supports.

v2: Change some style for patch 2.
    According Eric's suggestion, use the ether_addr_equal_64bits to instead
    of ether_addr_equal for patch 19.
    In fact, there are a lot of places which could use ether_addr_equal_64bits
    to instead of ether_addr_equal, but not this time, thanks for Joe's
    opinion.

v3: Change some style for patch 11/19:
    (net: packetengines: slight optimization of addr compare).
    Joe pointed out that is_broadcast_ether_addr(addr) would be appropriate here,
    but this should be left alone and not in this patch, so fix it later.

    In the patch (net: caif: slight optimization of addr compare), the operand for
    memcmp is not mac address, so it is unsuitable to use the ether_addr_equal
    to compare a non mac address, so remove the patch from the series.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: plip: slight optimization of addr compare

Use possibly more efficient ether_addr_equal_64bits
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fddi: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ti: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sun: optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: seeq: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: renesas: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qlcnic: slight optimization of addr compare

Use the possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned to instead of memcmp.

Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: netxen: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: packetengines: slight optimization of addr

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vxge: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ksz884x: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mlx4: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ixgbe: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: igbvf: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: benet: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: enic: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: cxgb3: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Santosh Raspatur <santosh@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: bnx2x: slight optimization of addr compare

Use the possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned to instead of memcmp.

Cc: Ariel Elior <ariele@broadcom.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: 3com: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net, sch: fix the typo in register_qdisc()

Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net, rps: fix the comment of net_rps_action_and_irq_enable()

Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net, rps: fix build failure when CONFIG_RPS isn't set

In file included from net/socket.c:99:0:
include/net/sock.h: In function ‘sock_rps_record_flow’:
include/net/sock.h:849:30: error: ‘const struct sock’ has no member named ‘sk_rxhash’
include/net/sock.h: In function ‘sock_rps_reset_flow’:
include/net/sock.h:854:29: error: ‘const struct sock’ has no member named ‘sk_rxhash’

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: move skb_dst_set() a bit downwards in sctp_packet_transmit()

skb_dst_set will use dst, if dst is NULL although is not a problem,
then goto the 'no_route' and free nskb, so do the skb_dst_set is pointless.
so move the skb_dst_set after dst check.
Remove the unnecessary initialization as well.

v2: fix the subject line because it would confuse people,
    as pointed out by Daniel.

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_netem: support of 64bit rates

Add a new attribute to support 64bit rates so that
tc can use them to break the 32bit limit.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_netem: more precise length of packets

With TSO/GSO/GRO packets, skb->len doesn't represent
a precise amount of bytes on wire.
This patch replace skb->len with qdisc_pkt_len(skb)
which is more precise.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling

When the device tunneling offloads mode is vxlan do the following

 - call SET_PORT with the relevant setting

 - add DMFS steering vxlan rule for the device self and multicast mac addresses
   of the form: {<ETH, outer-mac> <VXLAN, ANY vnid> <ETH, ANY mac>} --> RSS QP

 - set relevant QPC fields in RSS context and RX ring QPs

 - in TX flow, set WQE fields to generate HW checksum, and handle gso skbs
   which are marked for encapsulation such that the HW will segment them properly.

 - in RX flow, read HW offloaded checksum for encapsulated packets from the CQE

 - advertize hw_enc_features and NETIF_F_GSO_UDP_TUNNEL to the networking stack

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: Add basic support for TCP/IP offloads under tunneling

Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.

This is done through the following elements:

 - read tunneling device caps in QUERY_DEV_CAP
 - add helper function to do SET_PORT for tunneling
 - add DMFS VXLAN steering rule definitions
 - add CQE and WQE checksum offload field definitions

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: specify netlink packet direction for nlmon

In order to facilitate development for netlink protocol dissector,
fill the unused field skb->pkt_type of the cloned skb with a hint
of the address space of the new owner (receiver) socket in the
notion of "to kernel" resp. "to user".

At the time we invoke __netlink_deliver_tap_skb(), we already have
set the new skb owner via netlink_skb_set_owner_r(), so we can use
that for netlink_is_kernel() probing.

In normal PF_PACKET network traffic, this field denotes if the
packet is destined for us (PACKET_HOST), if it's broadcast
(PACKET_BROADCAST), etc.

As we only have 3 bit reserved, we can use the value (= 6) of
PACKET_FASTROUTE as it's _not used_ anywhere in the whole kernel
and not supported anywhere, and packets of such type were never
exposed to user space, so there are no overlapping users of such
kind. Thus, as wished, that seems the only way to make both
PACKET_* values non-overlapping and therefore device agnostic.

By using those two flags for netlink skbs on nlmon devices, they
can be made available and picked up via sll_pkttype (previously
unused in netlink context) in struct sockaddr_ll. We now have
these two directions:

 - PACKET_USER (= 6)    ->  to user space
 - PACKET_KERNEL (= 7)  ->  to kernel space

Partial `ip a` example strace for sa_family=AF_NETLINK with
detected nl msg direction:

syscall:                     direction:
sendto(3,  ...) = 40         /* to kernel */
recvmsg(3, ...) = 3404       /* to user */
recvmsg(3, ...) = 1120       /* to user */
recvmsg(3, ...) = 20         /* to user */
sendto(3,  ...) = 40         /* to kernel */
recvmsg(3, ...) = 168        /* to user */
recvmsg(3, ...) = 144        /* to user */
recvmsg(3, ...) = 20         /* to user */

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: only do not deliver to tap when both sides are kernel sks

We should also deliver packets to nlmon devices when we are in
netlink_unicast_kernel(), and only one of the {src,dst} sockets
is user sk and the other one kernel sk. That's e.g. the case in
netlink diag, netlink route, etc. Still, forbid to deliver messages
from kernel to kernel sks.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'sctp_logspam'

Neil Horman says:

====================
sctp: Consolidate and ratelimit deprecation warnings

The SCTP protocol has several deprecation warnings in its setsockopt path that
can be triggered by unprivlidged users.  Since these are not ratelimited, we can
spam the logs quite easily here.  Since these are all deprecation warnings, and
that type of warning isn't uncommon in the rest of the kernel, lets make a
common pr_warn_deprecated macro to produce somewhat generalized ratelimited
deprecation warnings easily
====================

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP: Reduce log spamming for sctp setsockopt

During a recent discussion regarding some sctp socket options, it was noted that
we have several points at which we issue log warnings that can be flooded at an
unbounded rate by any user.  Fix this by converting all the pr_warns in the
sctp_setsockopt path to be pr_warn_ratelimited.

Note there are several debug level messages as well.  I'm leaving those alone,
as, if you turn on pr_debug, you likely want lots of verbosity.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

printk: Add a DEPRECATED macro

sctp has several points in its setsockopt path in which it issues deprecation
warnings.  It seems like it might be handy to macrotize such a warning so other
subsystems can use it easily

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_dsmark: use correct func name in print messages

In dsmark_drop(), the function name printed by pr_debug
is "dsmark_reset", correct it to "dsmark_drop" by using
__func__ .

BTW, replace the other function names with __func__ .

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_htb: use /* comments

Do not use C99 // comments and correct a spelling typo.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: replace pr_warning with pr_warn

Prefer pr_warn(... to pr_warning(...

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

packet: fix "foo * bar" and "(foo*)" problems

Cleanup checkpatch errors.Specially,the second changed line
is exactly 80 columns long.

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: unneccessary to get address prefix in addrconf_get_prefix_route

Since addrconf_get_prefix_route inputs the address prefix to fib6_locate,
which does not uses the data which is out of the prefix_len length,
so do not need to use ipv6_addr_prefix to get address prefix.

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'tun_rfs'

Zhi Yong Wu says:

====================
tun: add the RFS support

Since Tom Herbert's hash related patchset was modified and got merged,
his pachset about adding support for RFS on tun flows also need to get
adjusted accordingly. I tried to update them, and before i will start
to do some perf tests, i hope to get one correct code base, so it's time
to post them out now. Any constructive comments are welcome, thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tun: Add support for RFS on tun flows

This patch adds support so that the rps_flow_tables (RFS) can be
programmed using the tun flows which are already set up to track flows
for the purposes of queue selection.

On the receive path (corresponding to select_queue and tun_net_xmit) the
rxhash is saved in the flow_entry.  The original code only does flow
lookup in select_queue, so this patch adds a flow lookup in tun_net_xmit
if num_queues == 1 (select_queue is not called from
dev_queue_xmit->netdev_pick_tx in that case).

The flow is recorded (processing CPU) in tun_flow_update (TX path), and
reset when flow is deleted.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Allow setting sock flow hash without a sock

This patch adds sock_rps_record_flow_hash and sock_rps_reset_flow_hash
which take a hash value as an argument and sets the sock_flow_table
accordingly.  This allows the table to be populated in cases where flow
is being tracked outside of a sock structure.

sock_rps_record_flow and sock_rps_reset_flow call this function
where the hash is taken from sk_rxhash.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: update Documentation/networking/bonding.txt for option lp_interval

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: ust micro BOND_NO_USE_ARP to simplify the mode check

The bond 3ad and TLB/ALB has the same check path, so combine them.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: add option lp_interval for loading module

The bond driver could set the lp_interval when loading module.

Suggested-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lro: remove dead code

Remove leftover code that is not used anywhere in current tree.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: make local function static

bond_xmit_slave_id is only used in main.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: make local functions static

The following are only used in one file:
  tcp_connect_init
  tcp_set_rto

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/7990: Make lance_private.name const

This allows to drop a few casts.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/7990: Fix whitespace errors

Most of them reported by checkpatch.pl

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>