wireless: Introduce defines for BAR TID_INFO & MULTI_TID fields

While at it also fix the indention of the other IEEE80211_BAR_CTRL_ defines.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: reload phy and bss settings after core restarts

b43_op_config and b43_op_bss_info_changed apply many settings by directly
writing to hardware registers. These settings are lost as soon as the core
is restarted and the initvals are reloaded. This was discovered because
restarting hostapd led to the beacon interval getting set to ~33s (see
https://dev.openwrt.org/ticket/8033 for more information).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: do btcoex ASPM disabling at initialization time

Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.

This need to be fixed for CONFIG_PCIEASPM, that will be done later ...

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: merge common ->config_pci_powersave() checks

Move common checks into wrapper function. Since ASPM can be only enabled
on PCIe devices ->is_pciexpress check is unneeded.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove ->config_pci_powersave() redundant argument

We always call ->config_pci_powersave() with both restore and power_off
arguments equal to 0 or both equal to 1, so merge them into one
argument.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

staging: remove ath6kl

ath6kl is now in drivers/net/wireless/ath so the staging driver
is not supported anymore and should be removed.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API

Instead of maintaining static scan table in driver, scan list is sent
to cfg80211 stack (after parsing each scan command response).
In assoc handler (for infra and ibss network) requested BSS information
is retrieved using cfg80211_get_bss() API.

With the changes above some redundant code are removed.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: avoid sending a-mpdu packets to sleeping stations

If the driver gets a tx status report for an A-MPDU sent to a station that
just went to sleep, that leaves a race condition where this tx status can
trigger another A-MPDU transmission.
To fix this, check if the station is sleeping before queueing the tid.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/cfg80211: Add extra IE configuration to AP mode setup

The NL80211_CMD_NEW_BEACON command is, in practice, requesting AP mode
operations to be started. Add new attributes to provide extra IEs
(e.g., WPS IE, P2P IE) for drivers that build Beacon, Probe Response,
and (Re)Association Response frames internally (likely in firmware).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/cfg80211: Add crypto settings into NEW_BEACON

This removes need from drivers to parse the beacon tail/head data
to figure out what crypto settings are to be used in AP mode in case
the Beacon and Probe Response frames are fully constructed in the
driver/firmware.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/cfg80211: Allow SSID to be specified in new beacon command

This makes it easier for drivers that generate Beacon and Probe Response
frames internally (in firmware most likely) in AP mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/mac80211: move information element parsing logic to cfg80211

Moving the parsing logic for retrieving the information elements
stored in management frames, e.g. beacons or probe responses,
and making it available to other cfg80211 drivers.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove eeprom txgain override for minor version < 19

ath9k_hw_4k_get_eeprom() overrides the eeprom value for txgain if the
minor version is not 19 or above with a value of 0.
ar9002_hw_init_mode_gain_regs() relies on this information to
determine whether this is a high power wifi card or not. The override
caused the driver to always use the 'normal' power tables even for
high power devices if their minor version was not high enough. Thus
leading to reduced power output.

This isn't needed for the AR9285; the check originated with the
AR9280 setup code which requires the EEPROM version check.

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/cfg80211: Make addition of new sinfo fields safer

Add a comment pointing out the use of enum station_info_flags for
all new struct station_info fields. In addition, memset the sinfo
buffer to zero before use on all paths in the current tree to avoid
leaving uninitialized pointers in the data.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix a crash in nl80211_send_station

mac80211 leaves sinfo->assoc_req_ies uninitialized, causing a random
pointer memory access in nl80211_send_station.
Instead of checking if the pointer is null, use sinfo->filled, like
the rest of the fields.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove obselete comments

the comments are obselete as the virtual wiphy support was removed from
the driver

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: optimize rate control statistics

for the ease of debugging, we display only the rate control statistics
for currently operating mode and bandwidth

Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix erroneous clearing of MESH_PATH_SN_VALID flag

When a PREQ or PREP is received from an intermediate node, it contains
useful information for path selection but it doesn't include the
originator's sequence number.   Therefore, when updating the mesh path
to that intermediate node, we should not set the MESH_PATH_SN_VALID
flag.  BUT, if the flag is set, it should not be unset as we might have
received a valid sequence number for that intermediate node in the past.

This issue was reported, fixed and tested by Ya Bo (游波) and Pedro
Larbig (ASPj).

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: minor clean-up

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clear sta.drv_priv on reconfiguration

drivers might assume sta.drv_priv is clear while
the sta is added, so clear it on reconfinguration.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/nl80211: Send AssocReq IEs to user space in AP mode

When user space SME/MLME (e.g., hostapd) is not used in AP mode, the
IEs from the (Re)Association Request frame that was processed in
firmware need to be made available for user space (e.g., RSN IE for
hostapd). Allow this to be done with cfg80211_new_sta().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: Indicate driver-based offchannel TX on mgmt_tx_cancel_wait

Drivers that support frame transmission with mgmt_tx() may not support
driver-based offchannel TX. Use mgmt_tx_cancel_wait instead of mgmt_tx
when figuring out whether to indicate support for this with
NL80211_ATTR_OFFCHANNEL_TX_OK.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: Fix RX status reporting for HT

RX_FLAG_HT must be included when reporting MCS rates. Without
this, mac80211 ended up dropping any frame sent at MCS index 12
or higher and that resulted in oddly random looking errors in
mac80211_hwsim tests.

Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://git./linux/kernel/git/kvalo/ath6kl

ath6kl: fix function name conflicts with ath9k

Stephen reported that compilation fails if both ath6kl and ath9k are
compiled in:

drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_start':
(.opd+0x600): multiple definition of `htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e40): first defined here
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_stop':
(.text+0x7b40): multiple definition of `.htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67b34): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_start':
(.text+0x7d18): multiple definition of `.htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67ba0): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_stop':
(.opd+0x5e8): multiple definition of `htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e28): first defined here

To fix this add ath6kl prefix to all public functions in htc.c.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Merge branch 'ath6kl-next' of /linux/kernel/git/kvalo/ath6kl

b43: Remove EXPERIMENTAL designation from LP PHY selection

Since kernel 3.0, the problems with controlling b43 devices that have
low-power (LP) PHYs have been fixed and the EXPERIMENTAL designation
can be fixed.

This patch also fixes a typo as the device supports 802.11b communications.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove some dead code in if_spi_prog_helper_firmware()

We always hit the goto and skip the printk().  The original code does
the right thing even though it looks messy.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix PCI interrupt processing race on SMP systems

When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.

Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.

While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove raw read/write routines from header

Now that the driver no longer uses the raw r/w routines, remove their definitions.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Eliminate raw reads and writes from PCIe portion

The PCIe driver used raw reads and writes on the PCIe hardware.
As all of these are only affecting the configuration space, all of
then can be converted to pci_{read,write}_config_XX calls.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use atomic reference count for interrupt ops

Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix incorrect spur_freq_sd for AR9003

Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.

Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: do not enable interrupt on set interrupt mask

At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: use register name in place of magic value

Signed-off-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: print driver version information

Add code to display driver version information in dmesg after
loading the driver successfully.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: implement if_sdio runtime power management

The SDIO card is now fully powered down when the network interface is
brought down.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: disable functionality when interface is down

Modify the driver so that it does not function when the interface is
down, in preparation for runtime power management.

No commands can be run while the interface is down, so the ndo_dev_stop
routine now directly does all necessary work (including asking the device
to disconnect from the network and disabling multicast functionality)
directly.

power_save and power_restore hooks are added meaning that card drivers
can take steps to turn the device off when the interface is down.

The MAC address can now only be changed when all interfaces are down;
the new address will be programmed when an interface gets brought up.
This matches mac80211 behaviour.

Also, some small cleanups/simplifications were made in the surrounding
device handling logic.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Don't use EAPOL frames for rate sampling

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fill in skb->protocol information for injected frames

Some drivers (ath9k for example) are using skb->protocol to treat EAPOL
frames somehow special (disallow aggregation for example).

When running in AP mode hostapd injects the EAPOL frames through a
monitor interface and thus skb->protocol isn't set at all. Hence, if the
injected frame is a data frame and carries a rfc1042 headaer update the
skb->protocol field accordingly.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Update REG_DBG_PRINT macro and uses

Several uses were missing terminating newlines.
Typo fix and macro neatening.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Update AR9003 high_power tx gain table

The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Update the radio parameters related to high_power

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Optimize rx descriptor processing for AR9003

No need to process RxDone and ds_info status again in case
valid rx status is given.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove virtual wiphy specific frame type

This patch cleanups virtual wiphy specific frametype structure

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Dump modal eeprom header

Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/modal_eeprom

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Dump base eeprom header

Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/base_eeprom

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add dump_eeprom support for eeprom_def

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add dump_eeprom support for AR9287

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add dump_eeprom support for eeprom_4k

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add dump_eeprom support for AR9003

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

lib80211: remove exports for functions not called by other modules

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: add core rev 17 used on bcma SoC.

This ieee80211 core was found on a Netgear wndr3400.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: use boardflags define from ssb code

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: define boardflags

They are SPROM specific, so all should be defined in ssb code.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath6kl: Release the memory allocated for the firmware

Nowhere the firmware memory is freed, free it during
the device destroy process.

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Fix crash during the connection process

Sometimes, the network manager is failing to connect to the AP due
to the below kernel crash message. The reason behind this,
after issuing the connect command to the chip, the chip is sending
disconnect event and then immediately one connect event to the host
in some random cases.

The host driver resets all states (including cfg80211 state machine)
when it receives disconnect event from the chip. But, still the host
driver reports the next received connect event to cfg80211, at that time
cfg80211 SME state would have been in IDLE state, which was causing
the below kernel crash.

Now, host driver's sme state machine is checked every time before
delivering connect event to cfg80211

  WARNING: at net/wireless/sme.c:517 cfg80211_connect_result+0x10d/0x120()
  [..]
  Call Trace:
  [<c0145732>] warn_slowpath_common+0x72/0xa0
  [<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
  [<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
  [<c0145782>] warn_slowpath_null+0x22/0x30
  [<c05d676d>] cfg80211_connect_result+0x10d/0x120
  [<f83ff497>] ath6kl_cfg80211_connect_event+0x427/0x4f0 [ath6kl]
  [<c035d26a>] ? put_dec+0x2a/0xa0
  [<c035d645>] ? number+0x365/0x380
  [<c0154675>] ? mod_timer+0x135/0x260
  [<c035e00e>] ? format_decode+0x2fe/0x370
  [<c01263c8>] ? default_spin_lock_flags+0x8/0x10
  [<c05fd91f>] ? _raw_spin_lock_irqsave+0x2f/0x50
  [<c0146032>] ? console_unlock+0x172/0x1c0
  [<f8402659>] ath6kl_connect_event+0x89/0x400 [ath6kl]
  [<f840826e>] ath6kl_wmi_control_rx+0x98e/0x1d60 [ath6kl]
  [<c01335b5>] ? __wake_up+0x45/0x60
  [<f84053aa>] ath6kl_rx+0x56a/0x770 [ath6kl]
  [<c04d0242>] ? mmc_release_host+0x22/0x40
  [<c04d9329>] ? sdio_release_host+0x19/0x30
  [<f840a27a>] ? ath6kl_sdio_read_write_sync+0x7a/0xc0 [ath6kl]
  [<f83f82b1>] do_rx_completion+0x41/0x50 [ath6kl]
  [<f83faa6a>] htc_rxmsg_pending_handler+0x6ba/0xbd0 [ath6kl]
  [<f8404bb0>] ? ath6kl_tx_data_cleanup+0x30/0x30 [ath6kl]
  [<f840a1c0>] ? ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
  [<f83f7cd5>] ath6kldev_intr_bh_handler+0x2a5/0x630 [ath6kl]
  [<f840a1c0>] ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
  [<c04d97c7>] sdio_irq_thread+0xc7/0x2d0
  [<c013aeb0>] ? default_wake_function+0x10/0x20
  [<c012fc98>] ? __wake_up_common+0x48/0x70
  [<c04d9700>] ? sdio_claim_irq+0x200/0x200
  [<c0163854>] kthread+0x74/0x80
  [<c01637e0>] ? kthread_worker_fn+0x160/0x160
  [<c0604c06>] kernel_thread_helper+0x6/0x10

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Cleanup void * in ath6kl_cfg80211_scan_node()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Use ath6kl_cfg80211_scan_node() directly instead of function pointer

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove ath6kl_wmi_iterate_nodes()

Use wlan_iterate_nodes() directly.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Pass only the needed scan_table to ath6kl_wmi_iterate_nodes()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move initialization/deinitialization of scan_table to appropriate functions

By having scan_table in struct ath6kl, it makes sense to move initialization
to ath6kl_init() and deinitialization to ath6kl_destroy().

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Cleanup parameters of wlan_node_table_init()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove ath6kl_wmi_get_current_bssid()

Use the bssid from ath6kl directly.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove bssid from struct wmi

This is nothing but bssid of struct ath6kl.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Cleanup parameters for wlan_refresh_inactive_nodes()

And remove the reference to wmi in ath6kl_node_table.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move scan table from wmi to ath6kl

It does not need to be in wmi

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Cleanup void *parent_dev in struct wmi

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: change aggreation timeout message from an error to a debug message

When I connect to my Linksys WT610N AP supporting 11n I see a lot of
aggreation timeout errors:

[  408.885053] ath6kl: aggr timeout (st 3109 end 3140)
[  463.872108] ath6kl: aggr timeout (st 3671 end 3702)
[  495.010060] ath6kl: aggr timeout (st 3983 end 4014)
[  503.604047] ath6kl: aggr timeout (st 4065 end 0)
[  518.963047] ath6kl: aggr timeout (st 141 end 172)
[  525.014066] ath6kl: aggr timeout (st 205 end 236)
[  573.957051] ath6kl: aggr timeout (st 701 end 732)
[  585.019067] ath6kl: aggr timeout (st 816 end 847)

But still the connection seems to work. To not clutter the logs change
the error message to a debug message. But add a fixme comment so that
this will be investigated.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: remove dependency to wireless extensions

ath6kl Kconfig still had dependencies to wext, remove those as they are
not needed anymore.

Now ath6kl should not have any wext code left. Time to have a beer and
celebrate this.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: fix crash when interface is closed but scan is ongoing

When ath6kl module was removed while a scan was ongoing the driver would
crash in ath6kl_cfg80211_scan_complete_event().

Fix the function not to iterate nodes when the scan is aborted. The nodes
are already freed when the module is being unloaded. This patch removes the
null check entirely as the wmi structure is not accessed anymore during
module unload.

Also fix a bug where the status was checked as a bitfield with '&' operator.
But it's not a bitfield, just a regular error code.

This is a port of my patch from ath6kl staging with the same title.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: fix atomicity in ath6kl_cfg80211_scan_node()

ath6kl_cfg80211_scan_node() was calling cfg80211_inform_bss_frame()
with CFP_KERNEL but the function is executed with a spin lock taken.
This is wrong and the function must use GFP_ATOMIC instead.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: don't force foreground scan when connected

In my setup data transfer stalls when there's data transmission during
scan. After some testing I found out that using background scan
when connected to makes the problem go away. This is more like
a workaround than a proper fix, but as the stall is so severe the
workaround is justified.

With a dual band card this increases scan time when connected from
1.9s to 4.4s. When not connected the scan time is not affected and
is the same 1.9s.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Use bit field macros to maintain wlan enabled and disabled status

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Avoid two memset to clear src and desr mac addr variable memory in ath6kl_wmi_dot11_hdr_remove()

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Rearrange the variable and the value position in IF condition

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Print bad trailer data only when htc fails to parse trailer info

Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove unused struct ath6kl_async_reg_io_buffer

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move chk_irq_status_cnt from ath6kl_device to htc_target

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Bypass reading irq status based on chk_irq_status_cnt

This is a regression.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move scatter information from ath6kl_device to htc_target

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move block_sz and block_mask from ath6kl_device to htc_target

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move bundle size from ath6kl_device to htc_target

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove callback msg_pending() and used the function directly

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Minor cleanup in ath6kldev_submit_scat_req()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove ath6kldev_setup_msg_bndl()

Use appropriate hif function directly.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Merge scatter rw request functions into one

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Refactor ath6kl_sdio_read_write_sync()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Moe virt_scat from hif_dev_scat_sup_info to hif_scatter_req

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Merge scatter gather setup functions for two method

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move down scatter enable and cleanup functions

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Cleanup ath6kl_sdio_cleanup_scatter()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Cleanup ath6kl_sdio_enable_scatter()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Refactor refactor ath6kl_sdio_setup_scat_resource()

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove endpoint reference from hif_scatter_req

Endpoint id ffrom htc_packet can be used instead.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove useless flags in hif_scatter_req

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Remove struct hif_scatter_req_priv

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Move ath6kl_sdio_async_rw_scatter() down to other hif_ops functions

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: cleanup callbacks for different scatter gather method

Define a hook in ath6kl_hif_ops for hif scatter gather mechanism.
When virtual scatter gather is used, call the respective function
directly.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add ath6kl cleaned up driver

Last May we started working on cleaning up ath6kl driver which is
currently in staging. The work has happened in a separate
ath6kl-cleanup tree:

http://git.kernel.org/?p=linux/kernel/git/kvalo/ath6kl-cleanup.git;a=summary

After over 1100 (!) patches we have now reached a state where I would
like to start discussing about pushing the driver to the wireless
trees and replacing the staging driver.

The driver is now a lot smaller and looks like a proper Linux driver.
The size of the driver (measured with simple wc -l) dropped from 49
kLOC to 18 kLOC and the number of the .c and .h files dropped from 107
to 22. Most importantly the number of subdirectories reduced from 26
to zero :)

There are two remaining checkpatch warnings in the driver which we
decided to omit for now:

drivers/net/wireless/ath/ath6kl/debug.c:31:
  WARNING: printk() should include KERN_ facility level
drivers/net/wireless/ath/ath6kl/sdio.c:527:
  WARNING: msleep < 20ms can sleep for up to 20ms;
  see Documentation/timers/timers-howto.txt

The driver has endian annotations for all the hardware specific
structures and there are no sparse errors. Unfortunately I don't have
any big endian hardware to test that right now.

We have been testing the driver both on x86 and arm platforms. The
code is also compiled with sparc and parisc cross compilers.

Notable missing features compared to the current staging driver are:

o HCI over SDIO support
o nl80211 testmode
o firmware logging
o suspend support

Testmode, firmware logging and suspend support will be added soon. HCI
over SDIO support will be more difficult as the HCI driver needs to
share code with the wifi driver. This is something we need to research
more.

Also I want to point out the changes I did for signed endian support.
As I wasn't able to find any support for signed endian annotations I
decided to follow what NTFS has done and added my own. Grep for sle16
and sle32, especially from wmi.h.

Various people have been working on the cleanup, the hall of
fame based on number of patches is:

   543  Vasanthakumar Thiagarajan
   403  Raja Mani
   252  Kalle Valo
    16  Vivek Natarajan
    12  Suraj Sumangala
     3  Joe Perches
     2  Jouni Malinen

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Suraj Sumangala <surajs@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>