GitHub/exynos8895/android_kernel_samsung_universal8895.git
17 years ago[TCP]: Don't panic if S+L skb is detected
Ilpo Järvinen [Fri, 27 Jul 2007 13:36:17 +0000 (16:36 +0300)]
[TCP]: Don't panic if S+L skb is detected

BUG_ON is an overkill. In fact, I was mislead by BUG_TRAP
severity (equals to WARN_ON) which is much lower than BUG_ON's
(that panics).

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Reduce sacked_out with reno when purging write_queue
Ilpo Järvinen [Thu, 9 Aug 2007 11:53:36 +0000 (14:53 +0300)]
[TCP]: Reduce sacked_out with reno when purging write_queue

Previously TCP had a transitional state during which reno
counted segments that are already below the current window into
sacked_out, which is now prevented. In addition, re-try now
the unconditional S+L skb catching.

This approach conservatively calls just remove_sack and leaves
reset_sack() calls alone. The best solution to the whole problem
would be to first calculate the new sacked_out fully (this patch
does not move reno_sack_reset calls from original sites and thus
does not implement this). However, that would require very
invasive change to fastretrans_alert (perhaps even slicing it to
two halves). Alternatively, all callers of tcp_packets_in_flight
(i.e., users that depend on sacked_out) should be postponed
until the new sacked_out has been calculated but it isn't any
simpler alternative.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Keep state in Disorder also if only lost_out > 0
Ilpo Järvinen [Sat, 7 Jul 2007 10:39:02 +0000 (13:39 +0300)]
[TCP]: Keep state in Disorder also if only lost_out > 0

This happens rather infrequently and is only possible during
FRTO. We must not allow TCP to slip to Open state because
tcp_fastretrans_alert might then not be called on it's time
when FRTO has exited. This become a problem when left_out
got removed and was replaced by just sacked_out.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Restore over-zealous tcp_sync_left_out-like removals
Ilpo Järvinen [Thu, 9 Aug 2007 11:45:17 +0000 (14:45 +0300)]
[TCP]: Restore over-zealous tcp_sync_left_out-like removals

tcp_verify_left_out is useful for verifying S+L condition, so
add it back to couple of places in where the code was not
calling to tcp_sync_left_out but used own ad-hoc solution
(before the tcp_sync_left_out got removed).

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Left out sync->verify (the new meaning of it) & definify
Ilpo Järvinen [Thu, 9 Aug 2007 11:44:16 +0000 (14:44 +0300)]
[TCP]: Left out sync->verify (the new meaning of it) & definify

Left_out was dropped a while ago, thus leaving verifying
consistency of the "left out" as only task for the function in
question. Thus make it's name more appropriate.

In addition, it is intentionally converted to #define instead
of static inline because the location of the invariant failure
is the most important thing to have if this ever triggers. I
think it would have been helpful e.g. in this case where the
location of the failure point had to be based on some quesswork:
    http://lkml.org/lkml/2007/5/2/464
...Luckily the guesswork seems to have proved to be correct.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Add tcp_left_out(tp) "back" to get cleaner looking lines
Ilpo Järvinen [Thu, 9 Aug 2007 11:37:30 +0000 (14:37 +0300)]
[TCP]: Add tcp_left_out(tp) "back" to get cleaner looking lines

tp->left_out got removed but nothing came to replace it back
then (users just did addition by themselves), so add function
for users now.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Tighten tcp_sock's belt, drop left_out
Ilpo Järvinen [Thu, 9 Aug 2007 11:33:18 +0000 (14:33 +0300)]
[TCP]: Tighten tcp_sock's belt, drop left_out

It is easily calculable when needed and user are not that many
after all.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Remove num_acked>0 checks from cong.ctrl mods pkts_acked
Ilpo Järvinen [Thu, 31 May 2007 07:16:47 +0000 (10:16 +0300)]
[TCP]: Remove num_acked>0 checks from cong.ctrl mods pkts_acked

There is no need for such check in pkts_acked because the
callback is not invoked unless at least one segment got fully
ACKed (i.e., the snd_una moved past skb's end_seq) by the
cumulative ACK's snd_una advancement.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Add tcp_dec_pcount_approx int variant
Ilpo Järvinen [Fri, 15 Jun 2007 09:58:38 +0000 (12:58 +0300)]
[TCP]: Add tcp_dec_pcount_approx int variant

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Move code from tcp_ecn.h to tcp*.c and tcp.h & remove it
Ilpo Järvinen [Sun, 27 May 2007 09:04:16 +0000 (02:04 -0700)]
[TCP]: Move code from tcp_ecn.h to tcp*.c and tcp.h & remove it

No other users exist for tcp_ecn.h. Very few things remain in
tcp.h, for most TCP ECN functions callers reside within a
single .c file and can be placed there.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Access to highest_sack obsoletes forward_cnt_hint
Ilpo Järvinen [Sun, 27 May 2007 09:03:20 +0000 (02:03 -0700)]
[TCP]: Access to highest_sack obsoletes forward_cnt_hint

In addition, added a reference about the purpose of the loop.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP] FRTO: remove unnecessary fackets/sacked_out recounting
Ilpo Järvinen [Sun, 27 May 2007 08:53:49 +0000 (01:53 -0700)]
[TCP] FRTO: remove unnecessary fackets/sacked_out recounting

F-RTO does not touch SACKED_ACKED bits at all, so there is no
need to recount them in tcp_enter_frto_loss. After removal of
the else branch, nested ifs can be combined.

This must also reset sacked_out when SACK is not in use as TCP
could have received some duplicate ACKs prior RTO. To achieve
that in a sane manner, tcp_reset_reno_sack was re-placed by the
previous patch.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Move Reno SACKed_out counter functions earlier
Ilpo Järvinen [Sun, 27 May 2007 08:52:00 +0000 (01:52 -0700)]
[TCP]: Move Reno SACKed_out counter functions earlier

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Extract DSACK detection code from tcp_sacktag_write_queue().
David S. Miller [Tue, 19 Jun 2007 05:43:06 +0000 (22:43 -0700)]
[TCP]: Extract DSACK detection code from tcp_sacktag_write_queue().

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Rexmit hint must be cleared instead of setting it
Ilpo Järvinen [Wed, 28 Mar 2007 19:06:37 +0000 (12:06 -0700)]
[TCP]: Rexmit hint must be cleared instead of setting it

Stupid error from my side. Even though now that I noticed this,
I hoped it would have been an optimization but no, the counter
hint is then incorrect. Thus clearing is necessary for now (I
still suspect though that this path is never executed).

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Extracted rexmit hint clearing from the LOST marking code
Ilpo Järvinen [Sat, 21 Apr 2007 05:56:38 +0000 (22:56 -0700)]
[TCP]: Extracted rexmit hint clearing from the LOST marking code

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Add highest_sack seqno, points to globally highest SACK
Ilpo Järvinen [Sun, 25 Mar 2007 04:03:23 +0000 (21:03 -0700)]
[TCP]: Add highest_sack seqno, points to globally highest SACK

It is guaranteed to be valid only when !tp->sacked_out. In most
cases this seqno is available in the last ACK but there is no
guarantee for that. The new fast recovery loss marking algorithm
needs this as entry point.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[NEIGH]: Netlink notifications
Thomas Graf [Thu, 9 Aug 2007 06:12:56 +0000 (23:12 -0700)]
[NEIGH]: Netlink notifications

Currently neighbour event notifications are limited to update
notifications and only sent if the ARP daemon is enabled. This
patch extends the existing notification code by also reporting
neighbours being removed due to gc or administratively and
removes the dependency on the ARP daemon. This allows to keep
track of neighbour states without periodically fetching the
complete neighbour table.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[NEIGH]: Combine neighbour cleanup and release
Thomas Graf [Thu, 9 Aug 2007 06:12:36 +0000 (23:12 -0700)]
[NEIGH]: Combine neighbour cleanup and release

Introduces neigh_cleanup_and_release() to be used after a
neighbour has been removed from its neighbour table. Serves
as preparation to add event notifications.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[MYRI10GE]: Use LRO.
Andrew Gallatin [Mon, 17 Sep 2007 18:37:42 +0000 (11:37 -0700)]
[MYRI10GE]: Use LRO.

Singed off by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[EHEA]: Use LRO.
Jan-Bernd Themann [Tue, 25 Sep 2007 23:16:34 +0000 (16:16 -0700)]
[EHEA]: Use LRO.

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[NET]: Generic Large Receive Offload for TCP traffic
Jan-Bernd Themann [Thu, 9 Aug 2007 05:38:05 +0000 (22:38 -0700)]
[NET]: Generic Large Receive Offload for TCP traffic

This patch provides generic Large Receive Offload (LRO) functionality
for IPv4/TCP traffic.

LRO combines received tcp packets to a single larger tcp packet and
passes them then to the network stack in order to increase performance
(throughput). The interface supports two modes: Drivers can either
pass SKBs or fragment lists to the LRO engine.

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[NET]: Virtual ethernet device driver.
Pavel Emelyanov [Tue, 25 Sep 2007 23:14:46 +0000 (16:14 -0700)]
[NET]: Virtual ethernet device driver.

Veth stands for Virtual ETHernet. It is a simple tunnel driver
that works at the link layer and looks like a pair of ethernet
devices interconnected with each other.

Mainly it allows to communicate between network namespaces but
it can be used as is as well.

The newlink callback is organized that way to make it easy to
create the peer device in the separate namespace when we have
them in kernel.

This implementation uses another interface - the RTM_NRELINK
message introduced by Patric.

Bug fixes from Daniel Lezcano.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[RTNETLINK]: Introduce generic rtnl_create_link().
Pavel Emelianov [Thu, 9 Aug 2007 05:16:38 +0000 (22:16 -0700)]
[RTNETLINK]: Introduce generic rtnl_create_link().

This routine gets the parsed rtnl attributes and creates a new
link with generic info (IFLA_LINKINFO policy). Its intention
is to help the drivers, that need to create several links at
once (like VETH).

This is nothing but a copy-paste-ed part of rtnl_newlink() function
that is responsible for creation of new device.

Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[NET]: Make NAPI polling independent of struct net_device objects.
Stephen Hemminger [Wed, 3 Oct 2007 23:41:36 +0000 (16:41 -0700)]
[NET]: Make NAPI polling independent of struct net_device objects.

Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.

In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.

The signature of the ->poll() call back goes from:

int foo_poll(struct net_device *dev, int *budget)

to

int foo_poll(struct napi_struct *napi, int budget)

The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract).  The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.

The napi_struct is to be embedded in the device driver private data
structures.

Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler.  Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.

With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.

Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.

[ Ported to current tree and all drivers converted.  Integrated
  Stephen's follow-on kerneldoc additions, and restored poll_list
  handling to the old style to fix mutual exclusion issues.  -DaveM ]

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[WIRELESS] radiotap parser: accept all other fields
Johannes Berg [Mon, 13 Aug 2007 12:04:30 +0000 (14:04 +0200)]
[WIRELESS] radiotap parser: accept all other fields

This makes the radiotap parser accept all other fields that are
currently defined.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: Add SIOCGIWTXPOWER routine
Larry Finger [Fri, 10 Aug 2007 16:23:20 +0000 (11:23 -0500)]
[MAC80211]: Add SIOCGIWTXPOWER routine

The wireless extensions ioctl's implemented in mac80211 do not include
SIOCGIWTXPOWER. This patch adds the necessary code.

Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[WIRELESS]: Use type safe netlink interface
Thomas Graf [Sun, 22 Jul 2007 10:43:32 +0000 (12:43 +0200)]
[WIRELESS]: Use type safe netlink interface

Makes use of the type safe netlink interface and adds a warning
if the message is too big for NLMSG_DEFAULT_SIZE to help debug.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: fix add_interface monitor mode behaviour
Johannes Berg [Fri, 27 Jul 2007 13:43:24 +0000 (15:43 +0200)]
[MAC80211]: fix add_interface monitor mode behaviour

This makes it behave the same whether we have monitor during operation
or not.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: Improve sanity checks on injected packets
Andy Green [Fri, 27 Jul 2007 13:43:24 +0000 (15:43 +0200)]
[MAC80211]: Improve sanity checks on injected packets

Michael Wu noticed that the skb length checking is not taken care of enough when
a packet is presented on the Monitor interface for injection.

This patch improves the sanity checking and removes fake offsets placed
into the skb network and transport header.

Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: Add get_unaligned to ieee80211_get_radiotap_len
Andy Green [Fri, 27 Jul 2007 13:43:24 +0000 (15:43 +0200)]
[MAC80211]: Add get_unaligned to ieee80211_get_radiotap_len

ieee80211_get_radiotap_len() tries to dereference radiotap length without
taking care that it is completely unaligned and get_unaligned()
is required.

Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: use more GFP_KERNEL instead of GFP_ATOMIC
Michael Wu [Fri, 27 Jul 2007 13:43:24 +0000 (15:43 +0200)]
[MAC80211]: use more GFP_KERNEL instead of GFP_ATOMIC

This patch replaces atomic allocations with regular ones where possible.

Merged with "revert some GFP_ATOMIC -> GFP_KERNEL changes" from Michael Wu:
> Some of the allocations made with GFP_ATOMIC really were necessary.

Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: implement ERP info change notifications
Daniel Drake [Fri, 27 Jul 2007 13:43:24 +0000 (15:43 +0200)]
[MAC80211]: implement ERP info change notifications

zd1211rw and bcm43xx are interested in being notified when ERP IE conditions
change, so that they can reprogram a register which affects how control frames
are transmitted.

This patch adds an interface similar to the one that can be found in softmac.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: improved short preamble handling
Daniel Drake [Fri, 27 Jul 2007 13:43:24 +0000 (15:43 +0200)]
[MAC80211]: improved short preamble handling

Similarly to CTS protection, whether short preambles are used for 802.11b
transmissions should be a per-subif setting, not device global.

For STAs, this patch makes short preamble handling automatic based on the ERP
IE. For APs, hostapd still uses the prism ioctls, but the write ioctl has been
restricted to AP-only subifs.

ieee80211_txrx_data.short_preamble (an unused field) was removed.

Unfortunately, some API changes were required for the following functions:
 - ieee80211_generic_frame_duration
 - ieee80211_rts_duration
 - ieee80211_ctstoself_duration
 - ieee80211_rts_get
 - ieee80211_ctstoself_get
Affected drivers were updated accordingly.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: Add LONG_RETRY flag to ieee80211_tx_control
Ivo van Doorn [Fri, 27 Jul 2007 13:43:23 +0000 (15:43 +0200)]
[MAC80211]: Add LONG_RETRY flag to ieee80211_tx_control

mac80211 informs the driver what the short and long retry values are through
set_retry_limit(), but when packets are being transmitted it did not inform the
driver which of the 2 retry limits should actually be used.
Instead it sends the actual value, but for drivers that can only set the retry limit
and the register and in the descriptor need to indicate which of the limits should
be used this is not really useful.

This patch will add a IEEE80211_TXCTL_LONG_RETRY_LIMIT flag to the
ieee80211_tx_control structure. By default the short retry limit should be
used but if the flag is set the long retry should be used.

This does not prevent the driver to ignore the request for "no retry" packets,
but at least those will be send out with the short retry limit. But there is no
perfect cure for this problem.. :(

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: STA reassociation improvements
Daniel Drake [Fri, 27 Jul 2007 13:43:23 +0000 (15:43 +0200)]
[MAC80211]: STA reassociation improvements

My cheapy D-Link AP behaves strangely w.r.t reassociations.

The following sequence of commands causes me to lose association and to be
unable to regain it:

ifconfig eth8 down
ifconfig eth8 up
iwconfig eth8 essid <x>

This is because mac80211 tries to reassociate, rather than just associate.
My AP replies with an association response (not a reassociation response...)
denying the association with code 12: "Association denied due to reason
outside the scope of this standard"

mac80211 tries this reassociation another 4 times or so before finally giving
up.

I see 2 problems here:
 1. bringing the interface down and up again should be resetting interface state
    i.e. after the interface is brought down, it should have no memory of if or
         where it was previously associated
 2. after the first reassociation fails, mac80211 should fall back to
    standard association for the next attempt

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: improve locking of sta_info related structures
Michael Wu [Fri, 27 Jul 2007 13:43:23 +0000 (15:43 +0200)]
[MAC80211]: improve locking of sta_info related structures

The sta_info code has some awkward locking which prevents some driver
callbacks from being allowed to sleep. This patch makes the locking more
focused so code that calls driver callbacks are allowed to sleep. It also
converts sta_lock to a rwlock.

Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: introduce util.c
Johannes Berg [Fri, 27 Jul 2007 13:43:23 +0000 (15:43 +0200)]
[MAC80211]: introduce util.c

Introduce a new file util.c and move a whole bunch of functions into it.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: reorder interface related functions
Johannes Berg [Fri, 27 Jul 2007 13:43:23 +0000 (15:43 +0200)]
[MAC80211]: reorder interface related functions

This patch groups a whole bunch of functions together to make
ieee80211.c more maintainable.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: move some rate control functions out of ieee80211.c
Johannes Berg [Fri, 27 Jul 2007 13:43:23 +0000 (15:43 +0200)]
[MAC80211]: move some rate control functions out of ieee80211.c

I think these can go with rate control just as well and it makes
ieee80211.c more readable.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: split out some key functions from ieee80211.c
Johannes Berg [Fri, 27 Jul 2007 13:43:23 +0000 (15:43 +0200)]
[MAC80211]: split out some key functions from ieee80211.c

into a new file key.c which doesn't have much code right now but
it makes ieee80211.c easier to read.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: remove some unnecessary includes
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: remove some unnecessary includes

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: split TX path into own file
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: split TX path into own file

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: rx cleanups (2)
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: rx cleanups (2)

Some more outdenting to make the code more readable.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: fix bug for per-sta stats
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: fix bug for per-sta stats

pre_rx handlers can't really touch sta since for IBSS it might not be
assigned yet, it can create sta info structs on-the-fly.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: split up __ieee80211_rx
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: split up __ieee80211_rx

The really indented part that does the huge switch on the interface
type is a nuisance. Put it into an own function 'prepare_for_handlers'.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: split ieee80211_rx_h_check handler
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: split ieee80211_rx_h_check handler

The ieee80211_rx_h_check handler really does two things, it's
a lot easier to understand if it's split into ieee80211_rx_h_check
and ieee80211_rx_h_load_key, and it may be possible in the future
to optimise the key loading to not do it for each interface.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: rx cleanups (1)
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: rx cleanups (1)

Make some really indented code more readable by outdenting.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: move QoS rx handlers into rx.c
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: move QoS rx handlers into rx.c

This patch moves the QoS handlers into rx.c making it possible
to compile wme.c only when NET_SCHED is defined.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[MAC80211]: split RX handlers into own file
Johannes Berg [Fri, 27 Jul 2007 13:43:22 +0000 (15:43 +0200)]
[MAC80211]: split RX handlers into own file

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years agoLinux 2.6.23
Linus Torvalds [Tue, 9 Oct 2007 20:31:38 +0000 (13:31 -0700)]
Linux 2.6.23

17 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Tue, 9 Oct 2007 19:38:44 +0000 (12:38 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Au1000: set the PCI controller IO base
  [MIPS] Alchemy: Fix USB initialization.
  [MIPS] IP32: Fix fatal typo in address computation.

17 years agoNLM: Fix a memory leak in nlmsvc_testlock
Trond Myklebust [Tue, 9 Oct 2007 15:04:57 +0000 (11:04 -0400)]
NLM: Fix a memory leak in nlmsvc_testlock

The recent fix for a circular lock dependency unfortunately introduced a
potential memory leak in the event where the call to nlmsvc_lookup_host
fails for some reason.

Thanks to Roel Kluin for spotting this.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agosata_mv: correct S/G table limits
Jeff Garzik [Tue, 9 Oct 2007 17:51:57 +0000 (13:51 -0400)]
sata_mv: correct S/G table limits

The recent mv_fill_sg() rewrite, to fix a data corruption problem
related to IOMMU virtual merging, forgot to account for the
potentially-increased size of the scatter/gather table after its run.

Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff
to more closely match the needs of mv_fill_sg().

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years ago[MIPS] Au1000: set the PCI controller IO base
Florian Fainelli [Tue, 25 Sep 2007 15:07:30 +0000 (17:07 +0200)]
[MIPS] Au1000: set the PCI controller IO base

The PCI controller IO base was not set in the au1000 pci code.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
17 years ago[MIPS] Alchemy: Fix USB initialization.
Florian Fainelli [Tue, 25 Sep 2007 15:07:24 +0000 (17:07 +0200)]
[MIPS] Alchemy: Fix USB initialization.

This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.

This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.

[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]

Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
17 years ago[MIPS] IP32: Fix fatal typo in address computation.
Giuseppe Sacco [Sat, 6 Oct 2007 17:55:03 +0000 (19:55 +0200)]
[MIPS] IP32: Fix fatal typo in address computation.

Signed-off-by: Giuseppe Sacco <eppesuig@debian.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
17 years agoCorrect Makefile rule for generating custom keymap
Maarten Bressers [Mon, 8 Oct 2007 22:59:13 +0000 (15:59 -0700)]
Correct Makefile rule for generating custom keymap

When building a custom keymap, after setting GENERATE_KEYMAP := 1 in
drivers/char/Makefile, the kernel build fails like this:

    CC      drivers/char/vt.o
  make[2]: *** No rule to make target `drivers/char/%.map', needed by `drivers/char/defkeymap.c'.  Stop.
  make[1]: *** [drivers/char] Error 2
  make: *** [drivers] Error 2

This was caused by commit af8b128719f5248e542036ea994610a29d0642a6, which
deleted a necessary colon from the Makefile rule that generates the keymap,
since that rule contains both a target and a target-pattern.  The following
patch puts the colon back:

Signed-off-by: Maarten Bressers <mbres@gentoo.org>
Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoISDN: Fix data access out of array bounds
Karsten Keil [Mon, 8 Oct 2007 10:52:09 +0000 (12:52 +0200)]
ISDN: Fix data access out of array bounds

Fix against access random data bytes outside the dev->chanmap array.
Thanks to Oliver Neukum for pointing me to this issue.

Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoMerge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Mon, 8 Oct 2007 19:59:10 +0000 (12:59 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPv6]: Fix ICMPv6 redirect handling with target multicast address
  [PKT_SCHED] cls_u32: error code isn't been propogated properly
  [ROSE]: Fix rose.ko oops on unload
  [TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed

17 years agoAIO: fix cleanup in io_submit_one(...)
Yan Zheng [Mon, 8 Oct 2007 19:16:20 +0000 (12:16 -0700)]
AIO: fix cleanup in io_submit_one(...)

When IOCB_FLAG_RESFD flag is set and iocb->aio_resfd is incorrect,
statement 'goto out_put_req' is executed. At label 'out_put_req',
aio_put_req(..) is called, which requires 'req->ki_filp' set.

Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agofix page release issue in filemap_fault
Yan Zheng [Mon, 8 Oct 2007 17:08:37 +0000 (10:08 -0700)]
fix page release issue in filemap_fault

find_lock_page increases page's usage count, we should decrease it
before return VM_FAULT_SIGBUS

Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agofix VM_CAN_NONLINEAR check in sys_remap_file_pages
Yan Zheng [Mon, 8 Oct 2007 17:05:48 +0000 (10:05 -0700)]
fix VM_CAN_NONLINEAR check in sys_remap_file_pages

The test for VM_CAN_NONLINEAR always fails

Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agomm: set_page_dirty_balance() vs ->page_mkwrite()
Peter Zijlstra [Mon, 8 Oct 2007 16:54:37 +0000 (18:54 +0200)]
mm: set_page_dirty_balance() vs ->page_mkwrite()

All the current page_mkwrite() implementations also set the page dirty. Which
results in the set_page_dirty_balance() call to _not_ call balance, because the
page is already found dirty.

This allows us to dirty a _lot_ of pages without ever hitting
balance_dirty_pages().  Not good (tm).

Force a balance call if ->page_mkwrite() was successful.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years ago[IPv6]: Fix ICMPv6 redirect handling with target multicast address
Brian Haley [Mon, 8 Oct 2007 07:12:05 +0000 (00:12 -0700)]
[IPv6]: Fix ICMPv6 redirect handling with target multicast address

When the ICMPv6 Target address is multicast, Linux processes the
redirect instead of dropping it.  The problem is in this code in
ndisc_redirect_rcv():

         if (ipv6_addr_equal(dest, target)) {
                 on_link = 1;
         } else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
                 ND_PRINTK2(KERN_WARNING
                            "ICMPv6 Redirect: target address is not
link-local.\n");
                 return;
         }

This second check will succeed if the Target address is, for example,
FF02::1 because it has link-local scope.  Instead, it should be checking
if it's a unicast link-local address, as stated in RFC 2461/4861 Section
8.1:

       - The ICMP Target Address is either a link-local address (when
         redirected to a router) or the same as the ICMP Destination
         Address (when redirected to the on-link destination).

I know this doesn't explicitly say unicast link-local address, but it's
implied.

This bug is preventing Linux kernels from achieving IPv6 Logo Phase II
certification because of a recent error that was found in the TAHI test
suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the
multicast address in the Destination field instead of Target field, so
we were passing the test.  This won't be the case anymore.

The patch below fixes this problem, and also fixes ndisc_send_redirect()
to not send an invalid redirect with a multicast address in the Target
field.  I re-ran the TAHI Neighbor Discovery section to make sure Linux
passes all 245 tests now.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[PKT_SCHED] cls_u32: error code isn't been propogated properly
Stephen Hemminger [Mon, 8 Oct 2007 06:57:45 +0000 (23:57 -0700)]
[PKT_SCHED] cls_u32: error code isn't been propogated properly

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[ROSE]: Fix rose.ko oops on unload
Alexey Dobriyan [Mon, 8 Oct 2007 06:44:17 +0000 (23:44 -0700)]
[ROSE]: Fix rose.ko oops on unload

Commit a3d384029aa304f8f3f5355d35f0ae274454f7cd aka
"[AX.25]: Fix unchecked rose_add_loopback_neigh uses"
transformed rose_loopback_neigh var into statically allocated one.
However, on unload it will be kfree's which can't work.

Steps to reproduce:

modprobe rose
rmmod rose

BUG: unable to handle kernel NULL pointer dereference at virtual address 00000008
 printing eip:
c014c664
*pde = 00000000
Oops: 0000 [#1]
PREEMPT DEBUG_PAGEALLOC
Modules linked in: rose ax25 fan ufs loop usbhid rtc snd_intel8x0 snd_ac97_codec ehci_hcd ac97_bus uhci_hcd thermal usbcore button processor evdev sr_mod cdrom
CPU:    0
EIP:    0060:[<c014c664>]    Not tainted VLI
EFLAGS: 00210086   (2.6.23-rc9 #3)
EIP is at kfree+0x48/0xa1
eax: 00000556   ebx: c1734aa0   ecx: f6a5e000   edx: f7082000
esi: 00000000   edi: f9a55d20   ebp: 00200287   esp: f6a5ef28
ds: 007b   es: 007b   fs: 0000  gs: 0033  ss: 0068
Process rmmod (pid: 1823, ti=f6a5e000 task=f7082000 task.ti=f6a5e000)
Stack: f9a55d20 f9a5200c 00000000 00000000 00000000 f6a5e000 f9a5200c f9a55a00
       00000000 bf818cf0 f9a51f3f f9a55a00 00000000 c0132c60 65736f72 00000000
       f69f9630 f69f9528 c014244a f6a4e900 00200246 f7082000 c01025e6 00000000
Call Trace:
 [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose]
 [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose]
 [<f9a51f3f>] rose_exit+0x4c/0xd5 [rose]
 [<c0132c60>] sys_delete_module+0x15e/0x186
 [<c014244a>] remove_vma+0x40/0x45
 [<c01025e6>] sysenter_past_esp+0x8f/0x99
 [<c012bacf>] trace_hardirqs_on+0x118/0x13b
 [<c01025b6>] sysenter_past_esp+0x5f/0x99
 =======================
Code: 05 03 1d 80 db 5b c0 8b 03 25 00 40 02 00 3d 00 40 02 00 75 03 8b 5b 0c 8b 73 10 8b 44 24 18 89 44 24 04 9c 5d fa e8 77 df fd ff <8b> 56 08 89 f8 e8 84 f4 fd ff e8 bd 32 06 00 3b 5c 86 60 75 0f
EIP: [<c014c664>] kfree+0x48/0xa1 SS:ESP 0068:f6a5ef28

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed
Ilpo Järvinen [Mon, 8 Oct 2007 06:43:10 +0000 (23:43 -0700)]
[TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed

When only GSO skb was partially ACKed, no hints are reset,
therefore fastpath_cnt_hint must be tweaked too or else it can
corrupt fackets_out. The corruption to occur, one must have
non-trivial ACK/SACK sequence, so this bug is not very often
that harmful. There's a fackets_out state reset in TCP because
fackets_out is known to be inaccurate and that fixes the issue
eventually anyway.

In case there was also at least one skb that got fully ACKed,
the fastpath_skb_hint is set to NULL which causes a recount for
fastpath_cnt_hint (the old value won't be accessed anymore),
thus it can safely be decremented without additional checking.

Reported by Cedric Le Goater <clg@fr.ibm.com>

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years agoDriver core: fix SYSF_DEPRECATED breakage for nested classdevs
Dmitry Torokhov [Sun, 7 Oct 2007 16:22:21 +0000 (12:22 -0400)]
Driver core: fix SYSF_DEPRECATED breakage for nested classdevs

We should only reparent to a class former class devices that
form the base of class hierarchy. Nested devices should still
grow from their real parents.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394...
Linus Torvalds [Sun, 7 Oct 2007 23:41:09 +0000 (16:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: point to migration document

17 years agoAdd manufacturer and card id of teltonica pcmcia modems
Attila Kinali [Sun, 7 Oct 2007 07:24:38 +0000 (00:24 -0700)]
Add manufacturer and card id of teltonica pcmcia modems

Add the manufacturer and card id of teltonica pcmcia modems to serial_cs.c

Signed-off-by: Attila Kinali <attila@kinali.ch>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agosysrq docs: document sequence that actually works
Pavel Machek [Sun, 7 Oct 2007 07:24:37 +0000 (00:24 -0700)]
sysrq docs: document sequence that actually works

Document sequence of keypresses that actually works. Yes, this changed
year-or-so ago.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agofix bogus reporting of signals by audit
Al Viro [Sun, 7 Oct 2007 07:24:36 +0000 (00:24 -0700)]
fix bogus reporting of signals by audit

Async signals should not be reported as sent by current in audit log.  As
it is, we call audit_signal_info() too early in check_kill_permission().
Note that check_kill_permission() has that test already - it needs to know
if it should apply current-based permission checks.  So the solution is to
move the call of audit_signal_info() between those.

Bogosity in question is easily reproduced - add a rule watching for e.g.
kill(2) from specific process (so that audit_signal_info() would not
short-circuit to nothing), say load_policy, watch the bogus OBJ_PID entry
in audit logs claiming that write(2) on selinuxfs file issued by
load_policy(8) had somehow managed to send a signal to syslogd...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Steve Grubb <sgrubb@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoMove kasprintf.o to obj-y
Alexey Dobriyan [Sun, 7 Oct 2007 07:24:34 +0000 (00:24 -0700)]
Move kasprintf.o to obj-y

Modulat lguest started giving linking errors

MODPOST 1 modules
ERROR: "kasprintf" [drivers/lguest/lg.ko] undefined!

Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agolockstat: documentation
Peter Zijlstra [Sun, 7 Oct 2007 07:24:33 +0000 (00:24 -0700)]
lockstat: documentation

Provide some documentation for CONFIG_LOCK_STAT.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoLonghaul: add auto enabled "revid_errata" option
Rafal Bilski [Sun, 7 Oct 2007 07:24:32 +0000 (00:24 -0700)]
Longhaul: add auto enabled "revid_errata" option

VIA C3 Ezra-T has RevisionID equal to 1, but it needs RevisionKey to be 0
or CPU will ignore new frequency and will continue to work at old
frequency.  New "revid_errata" option will force RevisionKey to be set to
0, whatever RevisionID is.

Additionaly "Longhaul" will not silently ignore unsuccessful transition.
It will try to check if "revid_errata" or "disable_acpi_c3" options need to
be enabled for this processor/system.

Same for Longhaul ver.  2 support.  It will be disabled if none of above
options will work.

 Best case scenario (with patch apllied and v2 enabled):
 longhaul: VIA C3 'Ezra' [C5C] CPU detected.  Longhaul v2 supported.
 longhaul: Using northbridge support.
 longhaul: VRM 8.5
 longhaul: Max VID=1.350  Min VID=1.050, 13 possible voltage scales
 longhaul: f: 300000 kHz, index: 0, vid: 1050 mV
 [...]
 longhaul: Voltage scaling enabled.
 Worst case scenario:
 longhaul: VIA C3 'Ezra-T' [C5M] CPU detected.  Powersaver supported.
 longhaul: Using northbridge support.
 longhaul: Using ACPI support.
 longhaul: VRM 8.5
 longhaul: Claims to support voltage scaling but min & max are both 1.250. Voltage scaling disabled
 longhaul: Failed to set requested frequency!
 longhaul: Enabling "Ignore Revision ID" option.
 longhaul: Failed to set requested frequency!
 longhaul: Disabling ACPI C3 support.
 longhaul: Disabling "Ignore Revision ID" option.
 longhaul: Failed to set requested frequency!
 longhaul: Enabling "Ignore Revision ID" option.

[akpm@linux-foundation.org: coding-style cleanups]
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoFix timer_stats printout of events/sec
Anton Blanchard [Sun, 7 Oct 2007 07:24:31 +0000 (00:24 -0700)]
Fix timer_stats printout of events/sec

When using /proc/timer_stats on ppc64 I noticed the events/sec field wasnt
accurate.  Sometimes the integer part was incorrect due to rounding (we
werent taking the fractional seconds into consideration).

The fraction part is also wrong, we need to pad the printf statement and
take the bottom three digits of 1000 times the value.

Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoDon't do load-average calculations at even 5-second intervals
Linus Torvalds [Sun, 7 Oct 2007 23:17:38 +0000 (16:17 -0700)]
Don't do load-average calculations at even 5-second intervals

It turns out that there are a few other five-second timers in the
kernel, and if the timers get in sync, the load-average can get
artificially inflated by events that just happen to coincide.

So just offset the load average calculation it by a timer tick.

Noticed by Anders Boström, for whom the coincidence started triggering
on one of his machines with the JBD jiffies rounding code (JBD is one of
the subsystems that also end up using a 5-second timer by default).

Tested-by: Anders Boström <anders@bostrom.dyndns.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoVT_WAITACTIVE: Avoid returning EINTR when not necessary
Linus Torvalds [Sun, 7 Oct 2007 23:02:55 +0000 (16:02 -0700)]
VT_WAITACTIVE: Avoid returning EINTR when not necessary

We should generally prefer to return ERESTARTNOHAND rather than EINTR,
so that processes with unhandled signals that get ignored don't return
EINTR.

This can help with X startup issues:

    Fatal server error:
    xf86OpenConsole: VT_WAITACTIVE failed: Interrupted system call

although the real fix is having the X server always retry EINTR
regardless (since EINTR does happen for signals that have handlers
installed). Keithp has a patch for that.

Regardless, ERESTARTNOHAND is the correct thing to use.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agofirewire: point to migration document
Stefan Richter [Sun, 7 Oct 2007 10:31:22 +0000 (12:31 +0200)]
firewire: point to migration document

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
17 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Sat, 6 Oct 2007 22:47:16 +0000 (15:47 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] IP32: Enable PCI bridges

17 years agoRevert "intel_agp: fix stolen mem range on G33"
Kyle McMartin [Sat, 6 Oct 2007 05:42:34 +0000 (01:42 -0400)]
Revert "intel_agp: fix stolen mem range on G33"

This reverts commit f443675affe3f16dd428e46f0f7fd3f4d703eeab, which
breaks horribly if you aren't running an unreleased xf86-video-intel
driver out of git.

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoFix non-terminated PCI match table in PowerMac IDE
Benjamin Herrenschmidt [Sat, 6 Oct 2007 08:52:27 +0000 (18:52 +1000)]
Fix non-terminated PCI match table in PowerMac IDE

The PCI device table in the powermac IDE driver isn't properly
terminated.  Depending on how your kernel is linked and other random
factors, you can end up with this driver matched against any other PCI
device in your system, possibly crashing at boot.

Thanks to Heikki for tracking this down with me, the bug have been there
for some time, though it rarely hurts due to luck.  In this case, the
switch from .22 to .23-rc9 is causing it to show up due to differences
in the resulting layout of .data I suppose.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <pmac@au1.ibm.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoxen: disable split pte locks for now
Jeremy Fitzhardinge [Sat, 6 Oct 2007 00:19:35 +0000 (17:19 -0700)]
xen: disable split pte locks for now

When pinning and unpinning pagetables, we must protect them against
being used by other CPUs, lest they see the pagetable in an
intermediate read-only-but-not-pinned state.

When using split pte locks, doing this properly would require taking
all the pte locks for the pagetable while pinning, but this may overflow
the PREEMPT_BITS part of the preempt counter if the process has mapped
more than about 512M of memory.

However, failing to take the pte locks causes write-protect faults when
the pageout code is trying to clear the Access bit on a pte which is part
of a freshy created and still being pinned process after fork.

This is a short-term fix until the problem is solved properly.

Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Keir Fraser <keir@xensource.com>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years agoMerge master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Fri, 5 Oct 2007 21:09:10 +0000 (14:09 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4598/2: OSIRIS: Ensure we do not get nRSTOUT during suspend
  [ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend

17 years ago[ARM] 4598/2: OSIRIS: Ensure we do not get nRSTOUT during suspend
Ben Dooks [Thu, 4 Oct 2007 22:18:08 +0000 (23:18 +0100)]
[ARM] 4598/2: OSIRIS: Ensure we do not get nRSTOUT during suspend

Ensure nRSTOUT is not asserted during or on resume.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
17 years ago[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend
Ben Dooks [Thu, 4 Oct 2007 22:16:42 +0000 (23:16 +0100)]
[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend

Ensure that CPLD is restored to the original state
on resume, and that before going into suspend we
select the NAND bank we booted from for restarting.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
17 years agor8169: revert part of 6dccd16b7c2703e8bbf8bca62b5cf248332afbe2
Francois Romieu [Wed, 3 Oct 2007 22:42:50 +0000 (00:42 +0200)]
r8169: revert part of 6dccd16b7c2703e8bbf8bca62b5cf248332afbe2

The 8169/8110SC currently announces itself as:
[...]
eth0: RTL8169sc/8110sc at 0x........, ..:..:..:..:..:.., XID 18000000 IRQ ..
                                                             ^^^^^^^^
It uses RTL_GIGA_MAC_VER_05 and this part of the changeset can cut
its performance by a factor of 2~2.5 as reported by Timo.

(the driver includes code just before the hunk to write the ChipCmd
register when mac_version == RTL_GIGA_MAC_VER_0[1-4])

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Timo Jantunen <jeti@welho.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoMerge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
Linus Torvalds [Fri, 5 Oct 2007 15:08:08 +0000 (08:08 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/sparc-2.6

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Fix 'niu' complex IRQ probing.
  [SPARC64]: check fork_idle() error
  [SPARC64]: Temporary workaround for PCI-E slot on T1000.
  [SPARC64]: VIO device addition log message level is too high.
  [SPARC64]: Fix domain-services port probing.
  [SPARC64]: Don't use in/local regs for ldx/stx data in N1 memcpy.

17 years agoRemove unnecessary cast in prefetch()
Serge Belyshev [Thu, 4 Oct 2007 21:10:04 +0000 (23:10 +0200)]
Remove unnecessary cast in prefetch()

It is ok to call prefetch() function with NULL argument, as specifically
commented in include/linux/prefetch.h.  But in standard C, it is invalid
to dereference NULL pointer (see C99 standard 6.5.3.2 paragraph 4 and
note #84).

prefetch() has a memory reference for its argument.

Newer gcc versions (4.3 and above) will use that to conclude that "x"
argument is non-null and thus wreaking havok everywhere prefetch() was
inlined.

Fixed by removing cast and changing asm constraint.

[ It seems in theory gcc 4.2 could miscompile this too; although no
  cases known.  In 2.6.24 we should probably switch to
  __builtin_prefetch() instead, but this is a simpler fix for now.
-- AK ]

Signed-off-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years ago[MIPS] IP32: Enable PCI bridges
Giuseppe Sacco [Thu, 4 Oct 2007 21:09:12 +0000 (23:09 +0200)]
[MIPS] IP32: Enable PCI bridges

Fixe MACE PCI addressing by adding the bus number parameter.
Remove check of the used slot since every slot should be valid.
Converted mkaddr from #define to inline function.

Signed-off-by: Giuseppe Sacco <eppesuig@debian.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
17 years ago[SPARC64]: Fix 'niu' complex IRQ probing.
David S. Miller [Thu, 4 Oct 2007 22:03:35 +0000 (15:03 -0700)]
[SPARC64]: Fix 'niu' complex IRQ probing.

They should be computed the same as how we compute
them under 'virtual-devices'.

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[SPARC64]: check fork_idle() error
Akinobu Mita [Thu, 4 Oct 2007 21:55:59 +0000 (14:55 -0700)]
[SPARC64]: check fork_idle() error

Check the return value of fork_idle() to catch error.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
17 years agoMerge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
Linus Torvalds [Thu, 4 Oct 2007 17:29:19 +0000 (10:29 -0700)]
Merge /linux/kernel/git/jejb/scsi-rc-fixes-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] megaraid_old: fix READ_CAPACITY

17 years agoFix sys_remap_file_pages BUG at highmem.c:15!
Hugh Dickins [Thu, 4 Oct 2007 15:56:06 +0000 (16:56 +0100)]
Fix sys_remap_file_pages BUG at highmem.c:15!

Gurudas Pai reports kernel BUG at arch/i386/mm/highmem.c:15! below
sys_remap_file_pages, while running Oracle database test on x86 in 6GB
RAM: kunmap thinks we're in_interrupt because the preempt count has
wrapped.

That's because __do_fault expected to unmap page_table, but one of its
two callers do_nonlinear_fault already unmapped it: let do_linear_fault
unmap it first too, and then there's no need to pass the page_table arg
down.

Why have we been so slow to notice this? Probably through forgetting
that the mapping_cap_account_dirty test means that sys_remap_file_pages
nowadays only goes the full nonlinear vma route on a few memory-backed
filesystems like ramfs, tmpfs and hugetlbfs.

[ It also depends on CONFIG_HIGHPTE, so it becomes even harder to
  trigger in practice. Many who have need of large memory have probably
  migrated to x86-64..

  Problem introduced by commit d0217ac04ca6591841e5665f518e38064f4e65bd
  ("mm: fault feedback #1")                -- Linus ]

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: gurudas pai <gurudas.pai@oracle.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
17 years ago[SCSI] megaraid_old: fix READ_CAPACITY
FUJITA Tomonori [Wed, 3 Oct 2007 00:00:58 +0000 (09:00 +0900)]
[SCSI] megaraid_old: fix READ_CAPACITY

The bulk transfer mode got eleminated by
3f6270ef76f2ce5c134615a470685d6c2a66c07e.  Unfortunately, this mode is
required for READ_CAPACITY commands on certain cards, so put it back
again.  This fixes a boot failure regression reported by Burton
Windle.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
17 years ago[SPARC64]: Temporary workaround for PCI-E slot on T1000.
David S. Miller [Thu, 4 Oct 2007 04:37:57 +0000 (21:37 -0700)]
[SPARC64]: Temporary workaround for PCI-E slot on T1000.

The PCI-E slot on T1000 connects directly to the Fire PCI chip with no
intervening bridges visible in the OBP tree.

Unfortunately the bus numbering of the device in that slot is
different (2) from the PCI host controller (0), and thus the
pci_bus_{read,write}_config_*() calls don't work out.

Complicating things further the Fire PCI controller has no config
space it responds to either.

For now treat this case specially so that devices in the slot work.

Longer term we need to perhaps cons up a dummy bridge between the Fire
and the PCI-E slot so that the bus hierarchy is complete inside of the
kernel and thus the bus numbering all works out right.

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[SPARC64]: VIO device addition log message level is too high.
David S. Miller [Thu, 4 Oct 2007 04:23:40 +0000 (21:23 -0700)]
[SPARC64]: VIO device addition log message level is too high.

There is no reason this should be KERN_ERR, KERN_INFO is
just fine.

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[SPARC64]: Fix domain-services port probing.
David S. Miller [Thu, 4 Oct 2007 04:08:11 +0000 (21:08 -0700)]
[SPARC64]: Fix domain-services port probing.

We should only use ports underneath "domain-services", other DS ports
in the MDESC aren't for us to use.

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years agoMerge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik...
Linus Torvalds [Wed, 3 Oct 2007 22:44:10 +0000 (15:44 -0700)]
Merge branch 'upstream-linus' of /linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  drivers/ata/pata_ixp4xx_cf.c: ioremap return code check
  Ata: pata_marvell, use ioread* for iomap-ped memory
  libata: fix for sata_mv >64KB DMA segments