iwlwifi: trigger scan synchronously

Scan requesting doesn't need to be asynchronous
since all code paths leading up to it can sleep.
Make the scan request a new util operation that
is hw-specific (to account for 3945 vs. agn)
and call it right in place.

This patch moves a lot of code into iwlagn as
it need not be in iwlcore.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: rename priv->scan to priv->scan_cmd

I keep checking what "priv->scan" is, so rename
it to "priv->scan_cmd" which more clearly tells
us what it is.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove scan_pass_start

Since we no longer do a multi-pass scan,
keeping track of how long each pass took
is pointless since there will only be one.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove next_scan_jiffies

This logic is just confusing, if anything it
belongs into mac80211. Also, even if we do
scan during the EAPOL handshake, that will
not cause any problems, just a short delay.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: correct atomic bitops usage

With atomic bitops, test_and_{set,clear}_bit
should be used instead of separate test_bit
and set_bit/clear_bit.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove scan_bands logic

Since mac80211 will now never request scanning
multiple bands, we can remove all the associated
logic and scan a single band only in each scan.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: set correct single/dual stream mask

Even the initial single/dual stream values will be overridden later when
issue link quality command; but still make sense not to use hard-code
value during initialization. Single/Dual stream mask are used to indicate the
best antenna for SISO/MIMO; different NIC has different tx antenna
configuration; so the parameter need to based on the valid tx antenna.

1x2 device: single tx antenna available, only SISO is valid
configuration, but still need to set up MIMO configuration, so set it up
with antenna A & B as default.
2x2 device: two tx antenna available, dual_stream will use both valid
antenna.

3x3 device: three tx antenna available, skip the first antenna and
choice the second and third antenna for dual_stream.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Merge branch 'wireless-2.6' into wireless-next-2.6

Conflicts:
drivers/net/wireless/iwlwifi/iwl-6000.c

iwlwifi: correct 6000 EEPROM regulatory address

For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.

Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported

And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: fix scan races

When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.

Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

wireless: rt2x00: rt2800usb: identify Sitecom devices

A very useful information was provided by Sitecom R&D guys:

Please find the information regarding our latest Ralink adapters below;

WL-302    -    VID: 0x0DF6,    PID: 0x002D    -    Ralink RT2771
WL-315    -    VID: 0x0DF6,    PID: 0x0039    -    Ralink RT2770
WL-319    -    VID: 0x182D,    PID: 0x0037    -    Ralink RT2860
WL-321    -    VID: 0x0DF6,    PID: 0x003B    -    Ralink RT2770
WL-324    -    VID: 0x0DF6,    PID: 0x003D    -    Ralink RT2870
WL-329    -    VID: 0x0DF6,    PID: 0x0041    -    Ralink RT3572
WL-343    -    VID: 0x0DF6,    PID: 0x003E    -    Ralink RT3070
WL-344    -    VID: 0x0DF6,    PID: 0x0040    -    Ralink RT3071
WL-345    -    VID: 0x0DF6,    PID: 0x0042    -    Ralink RT3072
WL-608    -    VID: 0x0DF6,    PID: 0x003F    -    Ralink RT2070

Note:
PID: 0x003C, 0x004A, and 0x004D:   --these products do not exist; devices were never produced/shipped--

The WL-349v4 USB dongle (0x0df6,0x0050) will be shipped soon (it isn't available yet), and uses a Ralink RT3370 chipset.

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170usb: add a couple more USB IDs

This patch adds the following 5 entries to the usbid device table:

 * Netgear WNA1000
 * Proxim ORiNOCO Dual Band 802.11n USB Adapter
 * 3Com Dual Band 802.11n USB Adapter
 * H3C Dual Band 802.11n USB Adapter
 * WNC Generic 11n USB dongle

CC: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: don't require NVS data when EEPROM is used

If EEPROM is used, NVS data is now loaded but ignored.
Stop loading it to avoid need of dummy NVS file for modules with EEPROM.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k-htc: fix lockdep warning and kernel warning after unplugging ar9271 usb device

This patch fixes two warnings below after unplugging ar9271 usb device:
-one is a kernel warning[1]
-another is a lockdep warning[2]

The root reason is that __skb_queue_purge can't be executed in hardirq
context, so the patch forks ath9k_skb_queue_purge(ath9k version of _skb_queue_purge),
which frees skb with dev_kfree_skb_any which can be run in hardirq
context safely, then prevent the lockdep warning and kernel warning after
unplugging ar9271 usb device.

[1] kernel warning
[  602.894005] ------------[ cut here ]------------
[  602.894005] WARNING: at net/core/skbuff.c:398 skb_release_head_state+0x71/0x87()
[  602.894005] Hardware name: 6475EK2
[  602.894005] Modules linked in: ath9k_htc ath9k ath9k_common ath9k_hw ath bridge stp llc sunrpc ipv6 cpufreq_ondemand acpi_cpufreq freq_table kvm_intel kvm arc4 ecb mac80211 snd_hda_codec_conexant snd_hda_intel snd_hda_codec snd_hwdep thinkpad_acpi snd_pcm snd_timer hwmon iTCO_wdt snd e1000e pcspkr i2c_i801 usbhid iTCO_vendor_support wmi cfg80211 yenta_socket rsrc_nonstatic pata_acpi snd_page_alloc soundcore uhci_hcd ohci_hcd ehci_hcd usbcore i915 drm_kms_helper drm i2c_algo_bit i2c_core video output [last unloaded: ath]
[  602.894005] Pid: 2506, comm: ping Tainted: G        W  2.6.34-rc3-wl #20
[  602.894005] Call Trace:
[  602.894005]  <IRQ>  [<ffffffff8104a41c>] warn_slowpath_common+0x7c/0x94
[  602.894005]  [<ffffffffa022f398>] ? __skb_queue_purge+0x43/0x4a [ath9k_htc]
[  602.894005]  [<ffffffff8104a448>] warn_slowpath_null+0x14/0x16
[  602.894005]  [<ffffffff813269c1>] skb_release_head_state+0x71/0x87
[  602.894005]  [<ffffffff8132829a>] __kfree_skb+0x16/0x81
[  602.894005]  [<ffffffff813283b2>] kfree_skb+0x7e/0x86
[  602.894005]  [<ffffffffa022f398>] __skb_queue_purge+0x43/0x4a [ath9k_htc]
[  602.894005]  [<ffffffffa022f560>] __hif_usb_tx+0x1c1/0x21b [ath9k_htc]
[  602.894005]  [<ffffffffa022f73c>] hif_usb_tx_cb+0x12f/0x154 [ath9k_htc]
[  602.894005]  [<ffffffffa00d2fbe>] usb_hcd_giveback_urb+0x91/0xc5 [usbcore]
[  602.894005]  [<ffffffffa00f6c34>] ehci_urb_done+0x7a/0x8b [ehci_hcd]
[  602.894005]  [<ffffffffa00f6f33>] qh_completions+0x2ee/0x376 [ehci_hcd]
[  602.894005]  [<ffffffffa00f8ba5>] ehci_work+0x95/0x76e [ehci_hcd]
[  602.894005]  [<ffffffffa00fa5ae>] ? ehci_irq+0x2f/0x1d4 [ehci_hcd]
[  602.894005]  [<ffffffffa00fa725>] ehci_irq+0x1a6/0x1d4 [ehci_hcd]
[  602.894005]  [<ffffffff810a6d18>] ? __rcu_process_callbacks+0x7a/0x2df
[  602.894005]  [<ffffffff810a47a4>] ? handle_fasteoi_irq+0x22/0xd2
[  602.894005]  [<ffffffffa00d268d>] usb_hcd_irq+0x4a/0xa7 [usbcore]
[  602.894005]  [<ffffffff810a2853>] handle_IRQ_event+0x77/0x14f
[  602.894005]  [<ffffffff813285ce>] ? skb_release_data+0xc9/0xce
[  602.894005]  [<ffffffff810a4814>] handle_fasteoi_irq+0x92/0xd2
[  602.894005]  [<ffffffff8100c4fb>] handle_irq+0x88/0x91
[  602.894005]  [<ffffffff8100baed>] do_IRQ+0x63/0xc9
[  602.894005]  [<ffffffff81354245>] ? ip_flush_pending_frames+0x4d/0x5c
[  602.894005]  [<ffffffff813ba993>] ret_from_intr+0x0/0x16
[  602.894005]  <EOI>  [<ffffffff811095fe>] ? __delete_object+0x5a/0xb1
[  602.894005]  [<ffffffff813ba5f5>] ? _raw_write_unlock_irqrestore+0x47/0x7e
[  602.894005]  [<ffffffff813ba5fa>] ? _raw_write_unlock_irqrestore+0x4c/0x7e
[  602.894005]  [<ffffffff811095fe>] __delete_object+0x5a/0xb1
[  602.894005]  [<ffffffff81109814>] delete_object_full+0x25/0x31
[  602.894005]  [<ffffffff813a60c0>] kmemleak_free+0x26/0x45
[  602.894005]  [<ffffffff810ff517>] kfree+0xaa/0x149
[  602.894005]  [<ffffffff81323fb7>] ? sock_def_write_space+0x84/0x89
[  602.894005]  [<ffffffff81354245>] ? ip_flush_pending_frames+0x4d/0x5c
[  602.894005]  [<ffffffff813285ce>] skb_release_data+0xc9/0xce
[  602.894005]  [<ffffffff813282a2>] __kfree_skb+0x1e/0x81
[  602.894005]  [<ffffffff813283b2>] kfree_skb+0x7e/0x86
[  602.894005]  [<ffffffff81354245>] ip_flush_pending_frames+0x4d/0x5c
[  602.894005]  [<ffffffff81370c1f>] raw_sendmsg+0x653/0x709
[  602.894005]  [<ffffffff81379e31>] inet_sendmsg+0x54/0x5d
[  602.894005]  [<ffffffff813207a2>] ? sock_recvmsg+0xc6/0xdf
[  602.894005]  [<ffffffff813208c1>] sock_sendmsg+0xc0/0xd9
[  602.894005]  [<ffffffff810e13b4>] ? might_fault+0x68/0xb8
[  602.894005]  [<ffffffff810e13fd>] ? might_fault+0xb1/0xb8
[  602.894005]  [<ffffffff8132a1c3>] ? copy_from_user+0x2f/0x31
[  602.894005]  [<ffffffff8132a5b3>] ? verify_iovec+0x54/0x91
[  602.894005]  [<ffffffff81320d41>] sys_sendmsg+0x1da/0x241
[  602.894005]  [<ffffffff8103d327>] ? finish_task_switch+0x0/0xc9
[  602.894005]  [<ffffffff8103d327>] ? finish_task_switch+0x0/0xc9
[  602.894005]  [<ffffffff8107642e>] ? trace_hardirqs_on_caller+0x16/0x150
[  602.894005]  [<ffffffff813ba27d>] ? _raw_spin_unlock_irq+0x56/0x63
[  602.894005]  [<ffffffff8103d3cb>] ? finish_task_switch+0xa4/0xc9
[  602.894005]  [<ffffffff8103d327>] ? finish_task_switch+0x0/0xc9
[  602.894005]  [<ffffffff810357fe>] ? need_resched+0x23/0x2d
[  602.894005]  [<ffffffff8107642e>] ? trace_hardirqs_on_caller+0x16/0x150
[  602.894005]  [<ffffffff813b9750>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[  602.894005]  [<ffffffff81009c02>] system_call_fastpath+0x16/0x1b
[  602.894005] ---[ end trace 91ba2d8dc7826839 ]---

[2] lockdep warning
[  169.363215] ======================================================
[  169.365390] [ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
[  169.366334] 2.6.34-rc3-wl #20
[  169.366872] ------------------------------------------------------
[  169.366872] khubd/78 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[  169.366872]  (clock-AF_INET){++.?..}, at: [<ffffffff81323f51>] sock_def_write_space+0x1e/0x89
[  169.366872]
[  169.366872] and this task is already holding:
[  169.366872]  (&(&hif_dev->tx.tx_lock)->rlock){-.-...}, at: [<ffffffffa03715b0>] hif_usb_stop+0x24/0x53 [ath9k_htc]
[  169.366872] which would create a new lock dependency:
[  169.366872]  (&(&hif_dev->tx.tx_lock)->rlock){-.-...} -> (clock-AF_INET){++.?..}
[  169.366872]
[  169.366872] but this new dependency connects a HARDIRQ-irq-safe lock:
[  169.366872]  (&(&hif_dev->tx.tx_lock)->rlock){-.-...}
[  169.366872] ... which became HARDIRQ-irq-safe at:
[  169.366872]   [<ffffffff810772d5>] __lock_acquire+0x2c6/0xd2b
[  169.366872]   [<ffffffff8107866d>] lock_acquire+0xec/0x119
[  169.366872]   [<ffffffff813b99bb>] _raw_spin_lock+0x40/0x73
[  169.366872]   [<ffffffffa037163d>] hif_usb_tx_cb+0x5e/0x154 [ath9k_htc]
[  169.366872]   [<ffffffffa00d2fbe>] usb_hcd_giveback_urb+0x91/0xc5 [usbcore]
[  169.366872]   [<ffffffffa00f6c34>] ehci_urb_done+0x7a/0x8b [ehci_hcd]
[  169.366872]   [<ffffffffa00f6f33>] qh_completions+0x2ee/0x376 [ehci_hcd]
[  169.366872]   [<ffffffffa00f8ba5>] ehci_work+0x95/0x76e [ehci_hcd]
[  169.366872]   [<ffffffffa00fa725>] ehci_irq+0x1a6/0x1d4 [ehci_hcd]
[  169.366872]   [<ffffffffa00d268d>] usb_hcd_irq+0x4a/0xa7 [usbcore]
[  169.366872]   [<ffffffff810a2853>] handle_IRQ_event+0x77/0x14f
[  169.366872]   [<ffffffff810a4814>] handle_fasteoi_irq+0x92/0xd2
[  169.366872]   [<ffffffff8100c4fb>] handle_irq+0x88/0x91
[  169.366872]   [<ffffffff8100baed>] do_IRQ+0x63/0xc9
[  169.366872]   [<ffffffff813ba993>] ret_from_intr+0x0/0x16
[  169.366872]   [<ffffffff8130f6ee>] cpuidle_idle_call+0xa7/0x115
[  169.366872]   [<ffffffff81008c4f>] cpu_idle+0x68/0xc4
[  169.366872]   [<ffffffff813a41e0>] rest_init+0x104/0x10b
[  169.366872]   [<ffffffff81899db3>] start_kernel+0x3f1/0x3fc
[  169.366872]   [<ffffffff818992c8>] x86_64_start_reservations+0xb3/0xb7
[  169.366872]   [<ffffffff818993c4>] x86_64_start_kernel+0xf8/0x107
[  169.366872]
[  169.366872] to a HARDIRQ-irq-unsafe lock:
[  169.366872]  (clock-AF_INET){++.?..}
[  169.366872] ... which became HARDIRQ-irq-unsafe at:
[  169.366872] ...  [<ffffffff81077349>] __lock_acquire+0x33a/0xd2b
[  169.366872]   [<ffffffff8107866d>] lock_acquire+0xec/0x119
[  169.366872]   [<ffffffff813b9d07>] _raw_write_lock_bh+0x45/0x7a
[  169.366872]   [<ffffffff8135cf14>] tcp_close+0x165/0x34d
[  169.366872]   [<ffffffff8137aced>] inet_release+0x55/0x5c
[  169.366872]   [<ffffffff81321350>] sock_release+0x1f/0x6e
[  169.366872]   [<ffffffff813213c6>] sock_close+0x27/0x2b
[  169.366872]   [<ffffffff8110dd45>] __fput+0x125/0x1ca
[  169.366872]   [<ffffffff8110de04>] fput+0x1a/0x1c
[  169.366872]   [<ffffffff8110adc9>] filp_close+0x68/0x72
[  169.366872]   [<ffffffff8110ae80>] sys_close+0xad/0xe7
[  169.366872]   [<ffffffff81009c02>] system_call_fastpath+0x16/0x1b

(Trimmed at the "other info that might help us debug this" line in
the interest of brevity... -- JWL)

Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k-htc:respect usb buffer cacheline alignment in reg out path

In ath9k-htc register out path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.

This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k-htc:respect usb buffer cacheline alignment in reg in path

In ath9k-htc register in path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.

This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).

Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k-htc:respect usb buffer cacheline alignment in ath9k_hif_usb_alloc_rx_urbs

In ath9k_hif_usb_alloc_rx_urbs, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.

This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skbs allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).

Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: treat RXORN as non-fatal

We get RXORN interrupts when all receive buffers are full. This is not
necessarily a fatal situation. It can also happen when the bus is busy or the
CPU is not fast enough to process all frames.

Older chipsets apparently need a reset to come out of this situration, but on
newer chips we can treat RXORN like RX, as going thru a full reset does more
harm than good, there.

The exact chip revisions which need a reset are unknown - this guess
AR5K_SREV_AR5212 ("venice") is copied from the HAL.

Inspired by openwrt 413-rxorn.patch:
"treat rxorn like rx, reset after rxorn seems to do more harm than good"

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use high bitrates for ACK/CTS

There was a confusion in the usage of the bits AR5K_STA_ID1_ACKCTS_6MB and
AR5K_STA_ID1_BASE_RATE_11B. If they are set (1), we will get lower bitrates for
ACK and CTS. Therefore ath5k_hw_set_ack_bitrate_high(ah, false) actually
resulted in high bitrates, which i think is what we want anyways. Cleared the
confusion and added some documentation.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add rt3390 support in rt2800 register initialization.

Add RT3390 specific register initializations to rt2x00, based on the latest
Ralink rt3390 vendor driver.

Untested as I don't actually own an RT3390 based device, but given experiences
on rt3070/rt3071 very hopeful that this will actually work..

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add rt3090 support in rt2800 register initialization.

Add RT3090 specific register initializations to rt2x00, based on the latest
Ralink rt3090 vendor driver.

Untested as I don't actually own an RT3090 based device, but given experiences
on rt3070/rt3071 very hopeful that this will actually work..

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add rt3071 support in rt2800 register initialization.

Add RT3071 specific register initializations to rt2x00, based on the latest
Ralink rt3070 vendor driver.

With this patch my RT3071 based devices start showing a sign of life.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Finish rt3070 support in rt2800 register initialization.

rt2x00 had preliminary support for RT3070 based devices, but the support was
incomplete.
Update the RT3070 register initialization to be similar to the latest Ralink
vendor driver.

With this patch my rt3070 based devices start showing a sign of life.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Align rt2800 register initialization with vendor driver.

Align the rt2800 register initializations with the latest versions of the
Ralink vendor driver.
This patch is also preparation for the addition of support for RT3070 /
RT3071 / RT3090 / RT3390 based devices.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Refactor rt2800 version constants.

The rt2800 version constants are inconsistent, and the version number don't
mean a lot of things anyway. Refactor the constants to have some more
meaningful names, and introduce and use some new helpers to check these
chipset revisions. At the same time rename to revision, as they are more
revision numbers rather than version numbers.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Align RT chipset definitions with vendor driver.

Only include definitions for RT chipsets that are also used inside the
Ralink vendor drivers.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Update rt2800 register definitions towards latest definitions.

Definitions taken from the latest rt2860 / rt2870 / rt3070 / rt3090 Ralink
vendor drivers.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Let RF chipset decide the RF channel switch method to use in rt2800.

It seems that the distinction between RF channel switch method is solely based
on the RF chipset that is used.
Refactor the channel switch decision to just take the RF chipset into account,
thereby greatly simplifying the check.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54pci: prevent stuck rx-ring on slow system

This patch fixes an old problem, which - under certain
circumstances - could cause the device to become
unresponsive.

most of p54pci's rx-ring management is implemented in just
two distinct standalone functions. p54p_check_rx_ring takes
care of processing incoming data, while p54p_refill_rx_ring
tries to replenish all depleted communication buffers.

This has always worked fine on my fast machine, but
now I know there is a hidden race...

The most likely candidate here is ring_control->device_idx.
Quintin Pitts had already analyzed the culprit and posted
a patch back in Oct 2009. But sadly, no one's picked up on this.
( https://patchwork.kernel.org/patch/53079/ [2 & 3] ).
This patch does the same way, except that it also prioritize
rx data processing, simply because tx routines *can* wait.

Reported-by: Sean Young <sean@mess.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11386
Reported-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

iwlwifi: avoid Tx queue memory allocation in interface down

We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.

This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: fix compiler warning

Check return code on iwl_send_cmd_pdu() to get rid of compiler warning.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: fix compile warnings when compiling without debug

Fixes:
CC [M]  drivers/net/wireless/iwlwifi/iwl-agn-rs.o
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2419: warning: unused variable ‘priv’
CC [M]  drivers/net/wireless/iwlwifi/iwl-sta.o
drivers/net/wireless/iwlwifi/iwl-sta.c: In function ‘iwl_send_add_sta’:
drivers/net/wireless/iwlwifi/iwl-sta.c:197: warning: unused variable ‘sta_id’

drivers/net/wireless/iwlwifi/iwl-3945.c: In function ‘iwl3945_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-3945.c:601: warning: unused variable ‘rx_stats_noise_diff’
drivers/net/wireless/iwlwifi/iwl-3945.c:600: warning: unused variable ‘rx_stats_sig_avg’
drivers/net/wireless/iwlwifi/iwl-3945-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-3945-rs.c:650: warning: unused variable ‘priv’

Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: small changes in comments

REPLY_TX_LINK_QUALITY_CMD was used by 4965, 5000 series and up

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: update tx command response status

Update to include additional tx command response status for "_agn"
devices.

The following status indicate the transmission was postponed:
  TX_STATUS_POSTPONE_DELAY
  TX_STATUS_POSTPONE_FEW_BYTES
  TX_STATUS_POSTPONE_BT_PRIO
  TX_STATUS_POSTPONE_QUIET_PERIOD
  TX_STATUS_POSTPONE_CALC_TTAK

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: add more debug info in error event dump

When sys assert happen, driver will dump the error table information
provided by uCode. There are more information available but is not being
display by the driver; adding program counter and last host command the
to log to help uCode debugging.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: clean up last_phy_res

The last_phy_res[100] variable is used in an odd
way. The first byte of it is used as a flag, and
the rest as the data. Thus, the array need only
be 61 bytes, since it is just the flag and a
struct iwl_rx_phy_res (which is 60 bytes).

Clean this up by splitting the variable into two:
last_phy_res and last_phy_res_valid, using correct
types for both (struct and bool). While doing all
this also move the variables to the _agn part of
the hw-specific union since they only apply to
A-MPDUs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove pointless sta_id invalid check

lq->sta_id cannot be invalid here since this
function will only be called after the station
has been added properly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlagn: simplify WEP key check

Simplify the WEP group key check by checking the
sta pointer instead of the sta_id we calculate
with it; also clean up the comment formatting.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove wrong key use check

Default WEP keys and regular keys are not allocated
from the same space in the firmware, so we shouldn't
use the same bits to indicate in use.

For default WEP keys, however, mac80211 won't allow
using the same key index twice, so the check is not
necessary at all -- add/remove are perfectly nested
due to those checks.

Other keys are allocated in the device in a global
array that only has a certain number of slots, so
for that we need to keep the allocation bitmap; but
the 802.11 key index isn't relevant there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: make WEP key restoring explicit

The firmware clears default WEP keys on
transitions to !associated, so we need
to restore them just like stations. This
is rather implicit as part of sending a
station right now, which is odd. Make it
explicit instead and only for agn since
3945 doesn't use hw crypto for WEP.

Due to that, iwl_send_static_wepkey_cmd
is now only used in iwl-sta.c and can be
static.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: default max event log size

Size of event log is determined by uCode which is different per NICs.
Set the maximum event log size per device to better match uCode
configuration.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: work around bogus active chains detection

The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.

The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.

This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

mac80211: check whether scan is in progress before queueing scan_work

As scan_work is queued from work_work it needs to be checked if scan
has been started during execution of work_work. Otherwise, when hw
scan is used, the stack gets error about hw being busy with ongoing
scan. This causes the stack to abort scan without notifying the driver
about it. This leads to a situation where the hw is scanning and the stack
thinks it's not. Then when the scan finishes, the stack will complain by
warnings.

Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Add support for connection quality monitoring

This patch will add support for connection quality monitoring by configuring
rssi triggers to the firmware, and enabling the firmware rssi trigger
functionality.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Go to ELP in idle

Allow the wl1271 go to ELP mode also in idle. This will reduce current
consumption remarkably in idle mode (~12mA -> ~0.2mA)

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix mac80211 RTS threshold requests during WL1271_STATE_OFF

mac80211 sends RTS threshold configuration request even if the wl1271 interface
state is WL1271_STATE_OFF. This leads to failures during pm tests.

This patch leaves the configuration function, if the interface is
going down.

Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix mac80211 configuration requests during WL1271_STATE_OFF

mac80211 sends configuration requests even if the wl1271 interface
state is WL1271_STATE_OFF. This creates warnings from mac80211.

This patch leaves the configuration functions, if the interface is
going down.

Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix memory leaks on driver initialization

This patch fixes some memory leaks occurring during driver init/de-init.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix typo for LDPC capability

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: delay skb linearising in rx decryption

We delay the skb linearising in ieee80211_rx_h_decrypt so that
frames do not require software decryption are not linearized. We
are safe to do this because ieee80211_get_mmie_keyidx() only
requires to touch nonlinear data for management frames, which are
already linearized before getting here.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Conflicts:
drivers/net/wireless/iwlwifi/iwl-4965.c

ath5k: fixup some merge damage for AR5211 IQ calibration

Resolution of a merge conflict upstream accidentally removed a hunk of
"ath5k: IQ calibration for AR5211 is slightly different", so restore it.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: need check for valid qos packet before free

For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: add sw_scan sw_scan_complete

Simple pre-scan and scan complete callbacks, this at least shows
to me that mac80211 will issue two scans at the same time on the
same wiphy.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add bounds check to pdadc table

We check the bounds on pdadc once when correcting for
negative curves but not when we later copy values from
from the pdadc_tmp array, leading to a potential overrun.

Although we shouldn't hit this case in practice, let's
be consistent.

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: fix race condition in tx desc processing

As pointed out by Benoit Papillault, there is a potential
race condition between the host and the hardware in reading
the next link in the transmit descriptor list:

cpu0              hw
                  tx for buf completed
                  raise tx_ok interrupt
process buf
buf->ds_link = 0
                  read buf->ds_link

This change checks txdp before processing a descriptor
(if there are any subsequent descriptors) to see if
hardware moved on.  We'll then process this descriptor on
the next tasklet.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: clean up queue manipulation

Review spotted a couple of strange invocations to
ieee80211_wake_queues that could potentially cause problems:

 - queues are awakened in the calibration tasklet before
   phy calibration, and then again after calibration

 - queues are awakened inside reset when we're trying to
   drain the ath5k transmit queues, and again after
   reset is completed (in callers to ath5k_reset_wake).

In both cases the first wake is unnecessary, so remove it.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: correct channel setting for 2.5 mhz spacing

These channels aren't selectable anyway, but our calculations
for 2.5 mhz frequencies are incorrect.  The value is supposed to
be:

  (frequency - reference) * (10/25)

i.e., divide by 2.5, but we were instead doing:

  (10 * frequency - reference) / 25.

Additionally, the check for (frequency % 5 == 2) had an extra
subtraction that wasn't in madwifi HAL.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: enhance tracing

Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: use rt2800_config_channel_rt3x for rt2872

rt2872 needs the same rf register setup as rt3070 and rt3090, hence
use rt2800_config_channel_rt3x instead of rt2800_config_channel_rt2x.
This change allows me to actually switch channels and hence scan all
configured channels on the RT305x SoC platform (which uses a rt2872)
here.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: simplify AR9220 fixup code for AR_AN_TOP2 register

Don't modify ah->iniModes, it's supposed to be constant.  Instead, apply
the fixup when the data is written to the registers.

Change ath9k_hw_init_eeprom_fix() to only determine whether the fixup is
needed.

This allows similteneous support for AR9220 cards that need AR_AN_TOP2
fixup (such as Ubiquiti SR71-12) and those that don't need it (D-Link
DWA-552 rev A2).

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix HTC layer memleak

Messages that are generated by the HTC layer
don't have any TX callback endpoints assigned to them.
Consequently, the allocated SKBs are never freed.

Fix this issue by handling this case in the HTC layer
itself.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Use anchors for REGOUT pipe

hif_usb_regout_cb() frees the given URB, which is
borked by design. Use an anchor to simplify URB
management.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix module unloading issue

The maximum number of packets in a single buffer in
stream mode is 10. The driver currently uses 8 - which
caused stack corruption, in the absence of any kind
of OOB checking.

Fixing this to the correct value of 10 fixes the module
unload issue.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix RX URB reference count

RX URBs are automatically freed when the reference
count drops to zero - this currently doesn't happen when
usb_kill_anchored_urbs() is called during unload.

Fix this by dropping the reference count by one during
initial submission.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Protect RX stream variables

Use a spin lock to prevent concurrent access
to variables dealing with RX stream mode handling.
Currently, no protection is implemented - which
causes problems in RX.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Enable powersaving by default again on rt2500usb.

Now that the powersave issues on rt2500usb have been tackled, powersave
can be enabled by default again.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Moved mesh action codes to a more visible location

Grouped mesh action codes together with the other action codes in
ieee80211.h.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless/ath: remove trailing space in messages

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6 into merge

Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/wireless/ath/ath5k/phy.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-core.h
drivers/net/wireless/iwlwifi/iwl-tx.c

mac80211: fix paged RX crypto

WEP crypto was broken, but upon finding the problem
it is evident that other things were broken by the
paged RX patch as well.

To fix it, for now move the linearising in front.
This means that we linearise all frames, which is
not at all what we want, but at least it fixes the
problem for now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix some RX aggregation locking

A few places in mac80211 do not currently acquire
the sta lock for RX aggregation, but they should.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up/fix aggregation code

The aggregation code has a number of quirks, like
inventing an unneeded WLAN_BACK_TIMER value and
leaking memory under certain circumstances during
station destruction. Fix these issues by using
the regular aggregation session teardown code and
blocking new aggregation sessions, all before the
station is really destructed.

As a side effect, this gets rid of the long code
block to destroy aggregation safely.

Additionally, rename tid_state_rx which can only
have the values IDLE and OPERATIONAL to
tid_active_rx to make it easier to understand
that there is no bitwise stuff going on on the
RX side -- the TX side remains because it needs
to keep track of the driver and peer states.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: rename WLAN_STA_SUSPEND to WLAN_STA_BLOCK_BA

I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove ieee80211_sta_stop_rx_ba_session

All callers of ieee80211_sta_stop_rx_ba_session can
just call __ieee80211_stop_rx_ba_session instead
because they already have the station struct, so do
that and remove ieee80211_sta_stop_rx_ba_session.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove irq disabling for sta lock

All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix station destruction problem

When a station w/o a key is destroyed, or when
a driver submits work for a station and thereby
references it again, it seems like potentially
we could reference the station structure while
it is being destroyed.

Wait for an RCU grace period to elapse before
finishing destroying the station after we have
removed the station from the driver and from
the hash table etc., even in the case where no
key is associated with the station.

Also, there's no point in deleting the plink
timer here since it'll be properly deleted just
a bit later.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Configure the beacon timers once the scan is completed.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add support for power save.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add support for newer AR9285 chipsets.

This patch adds support for a modified newer version of AR9285
chipsets.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add local-state-change-only auth/deauth/disassoc

cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.

Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.

Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: use DRIVER_NAME macro in wl1251_spi_driver

Better use the macro for consistency, the content is the same anyway.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Adaptive Noise Immunity (ANI) Implementation

This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked
at both ath9k and HAL sources (they are nearly the same), and even though i
have implemented some things differently, the basic algorithm is practically
the same, for now. I hope that this can serve as a clean start to improve the
algorithm later.

This also adds a possibility to manually control ANI settings, right now only
thru a debugfs file:
  * set lowest sensitivity (=highest noise immunity):
echo sens-low > /sys/kernel/debug/ath5k/phy0/ani
  * set highest sensitivity (=lowest noise immunity):
echo sens-high > /sys/kernel/debug/ath5k/phy0/ani
  * automatically control immunity (default):
echo ani-on > /sys/kernel/debug/ath5k/phy0/ani
  * to see the parameters in use and watch them change:
cat /sys/kernel/debug/ath5k/phy0/ani

Manually setting sensitivity will turn the automatic control off. You can also
control each of the five immunity parameters (noise immunity, spur immunity,
firstep, ofdm weak signal detection, cck weak signal detection) manually thru
the debugfs file.

This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix copy&paste typo

Reported-by: Myhailo Danylenko <isbear@ukrpost.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix tx queue flushing

This patch modifies tx-queue flushing to correspond with tx-path - i.e.
also frames for which no ack was requested are forwarded to the mac80211
for disposal.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix debug prints for beacon-loss and psm-entry-fail scenarios

Remove ERROR print from psm-entry-fail scenario, instead use an INFO print.
Also, add INFO print to the beacon-loss scenario.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Configure a higher listen interval to AP upon association

Increase the fixed listen-interval max value configured to the mac80211 on
driver init. This value will allow a larger value to be configured to the
AP, which means the AP will buffer our frames longer.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Configure rates for templates

Configure meaningful rates to be used with the templates. For control frames,
use the determined basic rates (currently the lowest rate for the band) and
for data-frames (null-funcs) let the firmware use the current rate policy to
determine the rate.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Use minimum rate for each band for control messages

Currently the mac80211 is not telling a hardware rate controlled driver a
rate to use for association frames etc. So to be safe, use the lowest rate
of each band for communication.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix keep-alive related command error

The firmware does not like the host configuring the keep-alive after it has
been once configured after a join-operation. Instead, it will complain about
invalid parameters, which do not break functionality, but do not look nice
in the syslog either.

This patch prevents the complaints by only configuring the keep-alive once
for an association, after the first time join is performed with the correct
bssid.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: added missing command header in wl1271_cmd_disconnect

The command header was missing in the wl1271_cmd_disconnect structure.  It
was working fine by sheer luck, because the parameters are not critical and
because our wl1271_cmd_send() function was overwriting the rx_config_options
with the actual header.

This patch adds the header to the command structure.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: fix sdio driver name in wl1271_sdio_driver

Our SPI driver is called "wl1271_spi" in the driver information structure.
Let's use the same for SDIO so that things are aligned.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add TL-WN422G v2 product ID

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Don't check devid for ath9k_htc

For USB devices, this check is invalid.
Remove the check so that new product IDs can be added.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Add a bus type field

This can be used to store the bus types ( AHB/PCI/USB ).

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix compile error without debug enabled

commits 8e6f5aa250d6013ec0d66f9f45f376678d3fc4ab and
db1a052b73f7c97f9e8b21f3f19a92313ed2acb1 accidentally introduced
compile errors that happens when ath9k debug is not enabled.
This patch fixes the declaration of the inline stubs to resolve this.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove ah->mask_reg, it's never used properly

ah->mask_reg was used to hold different data throughout the driver.
ath9k_hw_init_interrupt_masks() used it to save the value written to
AR_IMR.  ath9k_hw_set_interrupts() used it to hold the interrupt mask as
defined in enum ath9k_int.  Those masks differ in many bits.

Use ah->imask instead of ah->mask_reg in ath9k_hw_set_interrupts() and
ath9k_hw_updatetxtriglevel().  That's what the code was meant to do.
ah->imask is initialized in ath9k_start(), so we don't need to
initialize it from ah->mask_reg.

Once it's done, ah->mask_reg becomes write-only, so it's replaced with a
local variable in ath9k_hw_init_interrupt_masks().

Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: move imask from sc to ah

Add ah variable in the functions that didn't have it and used sc->imask.
Replace sc->sc_ah with ah in those functions.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: rename symbols in enum ath9k_internal_frame_type to avoid confusion

Symbols starting with "ATH9K_INT" are also used for interrupt mask.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>