ASoC: SAMSUNG: 24-bit audio playback on Exynos4210

Using 256fs or 512fs will result in distortion of 24-bit
audio samples. This is because the lrclk generated is not
proper. Using 384 fs generates proper output.

Signed-off-by: Giridhar Maruthy <giridhar.maruthy@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Don't warn on low WM8994/58 AIFnCLKs

We can have valid but very low clocks in accessory detection modes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use WM8994 FLL lock interrupt

If we have interrupts then wait for the FLL lock interrupt rather than
using dead reckoning when waiting for the FLL to start.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Hook up DC servo completion IRQ for WM8994 and WM8958

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Implement DC servo completion IRQ handling for wm_hubs devices

The individual devices should set the flag dcs_done_irq in the hubs
shared data structure to indicate that they will flag the interrupt
by calling wm_hubs_dcs_done().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use late enable handling for direct voice, speaker and headphone

This ensures appropriate clocking for bypass paths to speaker and
headphone and direct voice paths on affected revisions.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: STA32x: Preserve reserved register bits

Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched.  It is possible
there are differences between STA326 and STA328 or future
chip revisions in these bits, and clobbering them might
cause malfunction.

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: STA32x: Add mixer controls for biquad coefficients

The STA32x has a number of preset EQ settings, but also
allows full user control of the biquad filter coeffcients
(when "Automode EQ" is set to "User").
Each biquad has five signed, 24bit, fixed-point coefficients
representing the range -1...1.  The five biquad coefficients
can be uploaded in one atomic operation into on-chip
coefficient RAM.
There are also a few prescale, postscale and mixing
coefficients, in the same numeric format and range
(a negative coefficient inverts phase).

These coefficients are made available as SNDRV_CTL_ELEM_TYPE_BYTES
mixer controls.

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Conditionalize the enable of WM8994 ADC TDM mode

Future devices will not benefit from this.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Merge branch 'topic/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6 into for-3.1

Merge branch 'for-3.0' into for-3.1

ASoC: sh: fsi-hdmi: fixup snd_soc_card name

it shouldn't contain space letters and
special letters like parentheses.

aplay will be "Segmentation fault" without this patch
special thanks to Takashi.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sh: fsi-da7210: fixup snd_soc_card name

it shouldn't contain space letters and
special letters like parentheses.

aplay will be "Segmentation fault" without this patch.
special thanks to Takashi.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sh: fsi-ak4642: fixup snd_soc_card name

it shouldn't contain space letters and
special letters like parentheses.

aplay will be "Segmentation fault" without this patch.
special thanks to Takashi.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.1' of git://git./linux/kernel/git/broonie/sound-2.6 into topic/asoc

Merge branch 'for-3.0' into for-3.1

Merge branch 'for-3.0' of git://git./linux/kernel/git/broonie/sound-2.6 into fix/asoc

Merge branch 'for-3.0' into for-3.1

ASoC: pxa2xx-pcm: remove unused variable 'dai'

Remove unused variable 'dai' to eliminate below warning.

  CC      sound/soc/pxa/pxa2xx-pcm.o
sound/soc/pxa/pxa2xx-pcm.c: In function 'pxa2xx_soc_pcm_new':
sound/soc/pxa/pxa2xx-pcm.c:91: warning: unused variable 'dai'

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4642: fixup snd_soc_update_bits mask for PW_MGMT2

mask didn't cover update-data

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: Tegra: Implement SPDIF CPU DAI

This is a minimal driver for the Tegra SPDIF controller.

In hardware, the SPDIF output signal is always routed to any active HDMI
display controllers, and may also be routed to external pins on Tegra
using the pinmux.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core - Add platform IO tracing

Trace platform IO just like CODEC IO.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core - Add convenience register for platform kcontrol and DAPM

Allow platform probe to register platform kcontrols and DAPM just like
the CODEC probe().

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core - Add platform widget IO

Allow platform driver widgets to perform any IO required for DAPM.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core - Add API call to register platform kcontrols.

In preparation for Dynamic PCM (AKA DSP) support.

Allow platform drivers to register kcontrols.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Manage WM8731 ACTIVE bit as a supply widget

Now we have supply widgets there's no need to open code the handling of
the ACTIVE bit.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Manage WM8731 ACTIVE bit as a supply widget

Now we have supply widgets there's no need to open code the handling of
the ACTIVE bit.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Don't set invalid name string to snd_card->driver field

The snd_card->driver field contains a driver name string, and in
general it shouldn't contain space or special letters.  The commit
2b39535b9e54888649923beaab443af212b6c0fd changed the string copy from
card->name, but the long name string may contain such letters, thus
it may still lead to a segfault.

A temporary fix is not to copy the long name string but just keep it
empty as the earlier version did.

Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge branch 'for-3.1' of git://git./linux/kernel/git/broonie/sound-2.6 into topic/asoc

Merge branch 'for-3.0' of git://git./linux/kernel/git/broonie/sound-2.6 into fix/asoc

Merge branch 'for-3.1' of git://git./linux/kernel/git/lrg/asoc-2.6 into topic/asoc

Merge branch 'for-3.0' of git://git./linux/kernel/git/lrg/asoc-2.6 into fix/asoc

ASoC: core - Add platform read and write.

In preparation for ASoC Dynamic PCM (AKA DSP) support.

Allow platform driver to perform IO. Intended for platform DAPM.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic3x: Add correct hw registers to Line1 cross connect muxes

Commit af46800 ("ASoC: Implement mux control sharing") revealed that
"Left Line1[L | R] Mux" and "Right Line1[L | R] Mux" widgets were pointing
to the same kcontrols and codec registers and thus soc-core falsely detected
them as shared controls. This is actually wrong since there are separate
registers in hardware that configure Line1L to RADC and Line1R to LADC cross
connects so these muxes should not be shared.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

Merge branch 'for-3.0' into for-3.1

ASoC: Ensure we delay long enough for WM8994 FLL to lock when starting

This delay is very conservative.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

ASoC: Tegra: I2S: s/clk_get_sys/clk_get/

The clock needed by the I2S driver is associated with the I2S device name
in the standard fashion. Hence, use clk_get(dev) instead of clk_get_sys(clk_name).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Tegra: I2S: Ensure clock is enabled when writing regs

The I2S controller needs a clock to respond to register writes. Without
this, register writes will at worst hang the CPU. In practice, I've only
observed writes being dropped.

Luckily, the dropped register writes historically had no effect:

TEGRA_I2S_TIMING: The value we wrote was the reset default.

TEGRA_I2S_FIFO_SCR: The default was for the FIFOs to request more data
when one slot was empty. The requested value was for the FIFOs to request
when four slots were empty. The DMA controller in the mainline kernel is
configured to burst a single entry at a time into the FIFO, hence there
was no issue. The only negative effect was on bus efficiency losses due
to an increased number of arbitration attempts.

However, in various non-upstream changes, the DMA controller now bursts
four entries at a time into the FIFO. If there is only space for one
entry, the data is simply dropped. In practice, this resulted in 3/4 of
samples being dropped, and playback at 4x the expected rate and pitch.
By fixing the clocking issue, this is solved.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core - Make platform probe more like codec probe.

In preparation for ASoC dynamic PCM support (AKA ASoC DSP)

Platform will also support DAPM so separate out the probe function
to simplify the code (just like the codec probe).

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Improve error reporting in Speyside WM8962 driver

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Merge branch 'for-3.0' into for-3.1

ASoC: Change WM9081 speaker output enable to _OUT_DRV

More for neatness than any actual performance improvement.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Correct left/right swap in wm_hubs DC offset correction

It was consistently wrong for everything except WM8993 so should be no
functional change.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.comm>

ASoC: Fix Blackfin I2S _pointer() implementation return in bounds values

The Blackfin DMA controller can report one frame beyond the end of the
buffer in the wraparound case but ALSA requires that the pointer always
be in the buffer. Do the wraparound to handle this. A similar bug is
likely to apply to the other Blackfin PCM drivers but the code is less
obvious to inspection and I don't have a user to test.

Reported-by: Kieran O'Leary <Kieran.O'Leary@wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: Blackfin: Add machine driver for EVAL-ADAV80X boards

Add a machine driver to support the EVAL-ADAV801 and EVAL-ADAV803 boards
connected to a Analog Devices BF5XX evaluation board.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add ADAV80x codec driver

This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SAMSUNG: Add idma related register definition

This patch add idma related register definitions to support idma.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SAMSUNG: Move I2S common register definition

I2S registers can be used for control idma.
Previously, register is defined in i2s.c.
For sharing the registers, It is moved to i2s-regs.h

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SAMSUNG: Add WM8994 PCM Machine driver

This patch add WM8994 PCM machine driver to support PCM audio
on SMDKV310, SMDKC210 boards.
Playback and Capture supports 8kHz sampling rates.
and It is tested on SMDKV310, SMDKC210.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.0' into for-3.1

ASoC: pxa-ssp: Correct check for stream presence

Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: imx: add missing module informations

- add some modules aliases
- add module license to avoid tainted kernel when loading the imx-pcm-audio
  driver

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: imx: Remove unused Kconfig SND_MXC_SOC_SSI entry

SND_MXC_SOC_SSI looks to be unused, so kill it.

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add basic WM8918 support

The WM8918 is register compatible with the WM8904 with a subset of the
functionality. Add the device ID, a subsequent patch will ensure that only
the relevant functionality is exported to userspace.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Allow suppression of series updates on wm_hubs devices

Some devices do not support manual updates of the DC servo.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Trigger wm_hubs series update startup off a separate flag

Allowing the two to be used independently.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: add WM8782 ADC Codec Driver

Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: add STA32X codec driver

Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: codecs: Max98095: Fix logging of hardware revision.

The base hardware revision of the Maxim 98095 part is 0x40; the code
which outputs the revision of the hardware has been updated to
properly use uppercase alphabetic values for the revision numbers.

Also, the use of a constant for the length 'max98095_dai' has been
replaced with ARRAY_SIZE().

Signed-off-by: Taylor Hutt <thutt@chromium.org>
Acked-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: adau1701: signedness bug in adau1701_write()

"ret" is supposed to be signed here.  The current code will only
return -EIO on error, instead of a more appropriate error code such
as -EAGAIN etc.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix DAPM sequence run for per-widget I/O methods

Previously we were using the DAPM context rather than a widget as the
argument for update_bits() so we didn't need to care that our list walk
of widgets left us one beyond the end of the list. Now we're using them
for the register update we need to make sure we're pointing at an actual
widget not the list_head.

Fix originally suggested by Liam on IM.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Remove adau1701 from SND_SOC_ALL_CODECS due to Sigma dependency

The Sigma code is in drivers/firmware which is only included on a very
small subset of architectures and so ends up breaking the build on
others.  There's a pending patch to make the directory build as standard
but it's not merged yet.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add adau* drivers to the Analog Devices file patterns

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

ASoC: Blackfin: allow SPI for SSM2602 parts

This board has hardware switches for selecting SPI or I2C, so don't
require I2C for this driver.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: AD1836: rename suspend/resume funcs

Use less specific names for suspend/resume to match the probe/remove funcs
where these are now used.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: AD1836: fix codec name

The codec name should not have a "-codec" suffix since this is not part of
a MFD.  This was incorrectly changed during the multi-component updated.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: AD1836: fix intermixed tab/space indentation

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: AD1836: drop unnecessary spi register check

The only thing the init func does is register a spi driver, so if that
fails, we return the value back up to the caller who will display an
error message for us.  So drop the redundant checking/message.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: AD1836: clean up comment headers

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Blackfin: Add bf5xx-adau1701 machine driver

Add a machine driver to support the ADAU1701 SigmaDSP processors on
Analog Devices BF5XX evaluation boards.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add ADAU1701 codec driver

This patch adds support for the Analog Devices ADAU1701 SigmaDSP.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Clean up some coding style nits in the bf5xx-i2s-pcm driver

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: dapm - Refactor widget IO functions in preparation for platform widgets.

This time with soc_widget_update_bits reflecting recent soc_update_bits changes.

Currently widget IO is tightly coupled to the CODEC drivers. Future platform DSP
devices have mixer components that can alter power usage and hence require full
DAPM support.

This provides a generic widget IO operation wrapper in preparation for
future patches that implement platform driver DAPM.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix mismerge with release branch

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.0' into for-3.1

Trival fixup for move of I/O code into separate file.

Conflicts:
sound/soc/soc-cache.c

ASoC: Remove unused and about to be broken SND_SOC_CUSTOM I/O bus

This will be removed in -next so let's drop it from mainline as soon as
we can in order to minimise surprises.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Don't use codec->control_data in bulk write

In order to facilitate merging with the register map I/O replace the use
of control_data for the bulk writes with direct lookup of the client data
from the device.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add weak routes for sidetone style paths

Normally DAPM will power up any connected audio path. This is not ideal
for sidetone paths as with sidetone paths the audio path is not wanted in
itself, it is only desired if the two paths it provides a sidetone between
are both active. If the sidetone path causes a power up then it can be
hard to minimise pops as we first power up either the sidetone or the main
output path and then power the other, with the second power up potentially
introducing a DC offset.

Address this by introducing the concept of a weak path. If a path is marked
as weak then DAPM will ignore that path when walking the graph, though all
the relevant controls are still available to the application layer to allow
these paths to be configured.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Move register I/O code into a separate file

For clarity and to help ongoing refactoring in this area create a new file
to contain the physical I/O functions, separating them out from the cache
operations.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Factor out redundant read() functions

We've got a whole bunch of functions which just call straight through to
do_hw_read(). Simplify this situation by removing them and using hw_read()
directly.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: SMDKV310: Enable SPDIF device

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.0' into for-3.1

sound/atmel_ssc_dai: add a missing space to an error message

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SAMSUNG: Fix the incorrect referencing of I2SCON register

If DMA active status should be checked, I2SCON register should be referenced.
In this patch, Fix the incorrect referencing of I2SCON register.

Reported-by : Lakkyung Jung <lakkyung.jung@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: pcm - rename snd_codec_close() to snd_pcm_close().

Make sure we follow naming convention for all PCM ops.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core - PCM mutex per rtd

In preparation for the new ASoC Dynamic PCM support (AKA DSP support).

The new ASoC Dynamic PCM core allows DAIs to be dynamically re-routed
at runtime between the PCM device end (or Frontend - FE) and the physical DAI
(Backend - BE) using regular kcontrols (just like a hardware CODEC routes
audio in the analog domain). The Dynamic PCM core therefore must be
able to call PCM operations for both the Frontend and Backend(s) DAIs at
the same time.

Currently we have a global pcm_mutex that is used to serialise
the ASoC PCM operations. This patch removes the global mutex
and adds a mutex per RTD allowing the PCM operations to be reentrant and
allow control of more than one DAI at at time. e.g. a frontend PCM hw_params()
could configure multiple backend DAI hw_params() with similar or different
hw parameters at the same time.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.0' into for-3.1

ASoC: core - Separate out PCM operations into new file.

In preparation for Dynamic PCM support (AKA DSP support).

There will be future patches that add support to allow PCMs to be dynamically
routed to multiple DAIs at startup and also during stream runtime. This patch
moves the ASoC core PCM operaitions into a new file called soc-pcm.c.  This will
in simplify the ASoC core features into distinct files.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: snd_soc_new_{mixer,mux,pga} make sure to use right DAPM context

Currently it is possible that snd_soc_new_{mixer,mux,pga} is called with a
DAPM context not matching the widgets context. This can lead to a wrong
prefix_len calculation, which will result in undefined behaviour. To avoid
this always use the DAPM context from the widget itself.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Merge branch 'for-3.0' into for-3.1

ASoC: p1022ds: fix incorrect referencing of device tree properties

Device tree integer properties are encoded in big-endian format, but some of
the Freescale ASoC drivers were assuming that the host is in big-endian format
as well.  Although this is true, it's better to use endian-safe accessors.

Also add a check for a failed ioremap() call in the SSI driver.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fsl: fix initialization of DMA buffers

The DMA (PCM) driver used by some Freescale PowerPC supports separate DAIs
for playback and capture, so DMA buffers should be allocated only for the
initialized streams.  Instead of checking for the number of active channels,
which apparently is not reliable, check to see if the actual stream object
exists.

Also provide a better name for the DMA interrupt.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: WM8804 does not support sample rates below 32kHz

Reported-by: Kieran O'Leary <Kieran.O'Leary@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

ASoC: twl6040 - According to TWL6040 specification, gain start at 6dB and not -6dB.

Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

ASoC: Fix mismerge of Speyside set_bias_level_post()

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Merge branch 'for-3.0' into for-3.1

ASoC: Support Speyside build variants with WM8962 fitted

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Defer all WM8962 clocking configuration until power up

Don't require an audio rate SYSCLK in hw_params() in order to better
support microphone detection use cases.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Implement base 5 band EQ control for WM8962

ReTune Mobile modes are not currently supported.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Report errors when we have a WM8962 IRQ and don't get FLL lock

We really should be getting the interrupt - if we don't get one it's very
likely that the configuration is incorrect and audio will fail. Also
increase the timeout substantially in this case for safety.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>