gro: ensure frag0 meets IP header alignment

commit 38ec4944b593fd90c5ef42aaaa53e66ae5769d04 upstream.

After commit 0f6925b3e8da ("virtio_net: Do not pull payload in skb->head")
Guenter Roeck reported one failure in his tests using sh architecture.

After much debugging, we have been able to spot silent unaligned accesses
in inet_gro_receive()

The issue at hand is that upper networking stacks assume their header
is word-aligned. Low level drivers are supposed to reserve NET_IP_ALIGN
bytes before the Ethernet header to make that happen.

This patch hardens skb_gro_reset_offset() to not allow frag0 fast-path
if the fragment is not properly aligned.

Some arches like x86, arm64 and powerpc do not care and define NET_IP_ALIGN
as 0, this extra check will be a NOP for them.

Note that if frag0 is not used, GRO will call pskb_may_pull()
as many times as needed to pull network and transport headers.

Fixes: 0f6925b3e8da ("virtio_net: Do not pull payload in skb->head")
Fixes: 78a478d0efd9 ("gro: Inline skb_gro_header and cache frag0 virtual address")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_net: Do not pull payload in skb->head

commit 0f6925b3e8da0dbbb52447ca8a8b42b371aac7db upstream.

Xuan Zhuo reported that commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") brought  a ~10% performance drop.

The reason for the performance drop was that GRO was forced
to chain sk_buff (using skb_shinfo(skb)->frag_list), which
uses more memory but also cause packet consumers to go over
a lot of overhead handling all the tiny skbs.

It turns out that virtio_net page_to_skb() has a wrong strategy :
It allocates skbs with GOOD_COPY_LEN (128) bytes in skb->head, then
copies 128 bytes from the page, before feeding the packet to GRO stack.

This was suboptimal before commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") because GRO was using 2 frags per MSS,
meaning we were not packing MSS with 100% efficiency.

Fix is to pull only the ethernet header in page_to_skb()

Then, we change virtio_net_hdr_to_skb() to pull the missing
headers, instead of assuming they were already pulled by callers.

This fixes the performance regression, but could also allow virtio_net
to accept packets with more than 128bytes of headers.

Many thanks to Xuan Zhuo for his report, and his tests/help.

Fixes: 3226b158e67c ("net: avoid 32 x truesize under-estimation for tiny skbs")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://www.spinics.net/lists/netdev/msg731397.html
Co-Developed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: versatile: Fix up interrupt controller node names

[ Upstream commit 82a1c67554dff610d6be4e1982c425717b3c6a23 ]

Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:

        arch/arm/boot/dts/versatile-ab.dt.yaml:
        intc@10140000: $nodename:0: 'intc@10140000' does not match
        '^interrupt-controller(@[0-9a-f,]+)*$'

arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: 'clear-mask' does not match any of the regexes

Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@.. Also drop invalid
clear-mask property.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210701132118.759454-1-sudeep.holla@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hfs: add lock nesting notation to hfs_find_init

[ Upstream commit b3b2177a2d795e35dc11597b2609eb1e7e57e570 ]

Syzbot reports a possible recursive lock in [1].

This happens due to missing lock nesting information.  From the logs, we
see that a call to hfs_fill_super is made to mount the hfs filesystem.
While searching for the root inode, the lock on the catalog btree is
grabbed.  Then, when the parent of the root isn't found, a call to
__hfs_bnode_create is made to create the parent of the root.  This
eventually leads to a call to hfs_ext_read_extent which grabs a lock on
the extents btree.

Since the order of locking is catalog btree -> extents btree, this lock
hierarchy does not lead to a deadlock.

To tell lockdep that this locking is safe, we add nesting notation to
distinguish between catalog btrees, extents btrees, and attributes
btrees (for HFS+).  This has already been done in hfsplus.

Link: https://syzkaller.appspot.com/bug?id=f007ef1d7a31a469e3be7aeb0fde0769b18585db
Link: https://lkml.kernel.org/r/20210701030756.58760-4-desmondcheongzx@gmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reported-by: syzbot+b718ec84a87b7e73ade4@syzkaller.appspotmail.com
Tested-by: syzbot+b718ec84a87b7e73ade4@syzkaller.appspotmail.com
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hfs: fix high memory mapping in hfs_bnode_read

[ Upstream commit 54a5ead6f5e2b47131a7385d0c0af18e7b89cb02 ]

Pages that we read in hfs_bnode_read need to be kmapped into kernel
address space.  However, currently only the 0th page is kmapped.  If the
given offset + length exceeds this 0th page, then we have an invalid
memory access.

To fix this, we kmap relevant pages one by one and copy their relevant
portions of data.

An example of invalid memory access occurring without this fix can be seen
in the following crash report:

  ==================================================================
  BUG: KASAN: use-after-free in memcpy include/linux/fortify-string.h:191 [inline]
  BUG: KASAN: use-after-free in hfs_bnode_read+0xc4/0xe0 fs/hfs/bnode.c:26
  Read of size 2 at addr ffff888125fdcffe by task syz-executor5/4634

  CPU: 0 PID: 4634 Comm: syz-executor5 Not tainted 5.13.0-syzkaller #0
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
  Call Trace:
   __dump_stack lib/dump_stack.c:79 [inline]
   dump_stack+0x195/0x1f8 lib/dump_stack.c:120
   print_address_description.constprop.0+0x1d/0x110 mm/kasan/report.c:233
   __kasan_report mm/kasan/report.c:419 [inline]
   kasan_report.cold+0x7b/0xd4 mm/kasan/report.c:436
   check_region_inline mm/kasan/generic.c:180 [inline]
   kasan_check_range+0x154/0x1b0 mm/kasan/generic.c:186
   memcpy+0x24/0x60 mm/kasan/shadow.c:65
   memcpy include/linux/fortify-string.h:191 [inline]
   hfs_bnode_read+0xc4/0xe0 fs/hfs/bnode.c:26
   hfs_bnode_read_u16 fs/hfs/bnode.c:34 [inline]
   hfs_bnode_find+0x880/0xcc0 fs/hfs/bnode.c:365
   hfs_brec_find+0x2d8/0x540 fs/hfs/bfind.c:126
   hfs_brec_read+0x27/0x120 fs/hfs/bfind.c:165
   hfs_cat_find_brec+0x19a/0x3b0 fs/hfs/catalog.c:194
   hfs_fill_super+0xc13/0x1460 fs/hfs/super.c:419
   mount_bdev+0x331/0x3f0 fs/super.c:1368
   hfs_mount+0x35/0x40 fs/hfs/super.c:457
   legacy_get_tree+0x10c/0x220 fs/fs_context.c:592
   vfs_get_tree+0x93/0x300 fs/super.c:1498
   do_new_mount fs/namespace.c:2905 [inline]
   path_mount+0x13f5/0x20e0 fs/namespace.c:3235
   do_mount fs/namespace.c:3248 [inline]
   __do_sys_mount fs/namespace.c:3456 [inline]
   __se_sys_mount fs/namespace.c:3433 [inline]
   __x64_sys_mount+0x2b8/0x340 fs/namespace.c:3433
   do_syscall_64+0x37/0xc0 arch/x86/entry/common.c:47
   entry_SYSCALL_64_after_hwframe+0x44/0xae
  RIP: 0033:0x45e63a
  Code: 48 c7 c2 bc ff ff ff f7 d8 64 89 02 b8 ff ff ff ff eb d2 e8 88 04 00 00 0f 1f 84 00 00 00 00 00 49 89 ca b8 a5 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
  RSP: 002b:00007f9404d410d8 EFLAGS: 00000246 ORIG_RAX: 00000000000000a5
  RAX: ffffffffffffffda RBX: 0000000020000248 RCX: 000000000045e63a
  RDX: 0000000020000000 RSI: 0000000020000100 RDI: 00007f9404d41120
  RBP: 00007f9404d41120 R08: 00000000200002c0 R09: 0000000020000000
  R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000003
  R13: 0000000000000003 R14: 00000000004ad5d8 R15: 0000000000000000

  The buggy address belongs to the page:
  page:00000000dadbcf3e refcount:0 mapcount:0 mapping:0000000000000000 index:0x1 pfn:0x125fdc
  flags: 0x2fffc0000000000(node=0|zone=2|lastcpupid=0x3fff)
  raw: 02fffc0000000000 ffffea000497f748 ffffea000497f6c8 0000000000000000
  raw: 0000000000000001 0000000000000000 00000000ffffffff 0000000000000000
  page dumped because: kasan: bad access detected

  Memory state around the buggy address:
   ffff888125fdce80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
   ffff888125fdcf00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
  >ffff888125fdcf80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
                                                                  ^
   ffff888125fdd000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
   ffff888125fdd080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
  ==================================================================

Link: https://lkml.kernel.org/r/20210701030756.58760-3-desmondcheongzx@gmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hfs: add missing clean-up in hfs_fill_super

[ Upstream commit 16ee572eaf0d09daa4c8a755fdb71e40dbf8562d ]

Patch series "hfs: fix various errors", v2.

This series ultimately aims to address a lockdep warning in
hfs_find_init reported by Syzbot [1].

The work done for this led to the discovery of another bug, and the
Syzkaller repro test also reveals an invalid memory access error after
clearing the lockdep warning.  Hence, this series is broken up into
three patches:

1. Add a missing call to hfs_find_exit for an error path in
   hfs_fill_super

2. Fix memory mapping in hfs_bnode_read by fixing calls to kmap

3. Add lock nesting notation to tell lockdep that the observed locking
   hierarchy is safe

This patch (of 3):

Before exiting hfs_fill_super, the struct hfs_find_data used in
hfs_find_init should be passed to hfs_find_exit to be cleaned up, and to
release the lock held on the btree.

The call to hfs_find_exit is missing from an error path.  We add it back
in by consolidating calls to hfs_find_exit for error paths.

Link: https://syzkaller.appspot.com/bug?id=f007ef1d7a31a469e3be7aeb0fde0769b18585db
Link: https://lkml.kernel.org/r/20210701030756.58760-1-desmondcheongzx@gmail.com
Link: https://lkml.kernel.org/r/20210701030756.58760-2-desmondcheongzx@gmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sctp: move 198 addresses from unusable to private scope

[ Upstream commit 1d11fa231cabeae09a95cb3e4cf1d9dd34e00f08 ]

The doc draft-stewart-tsvwg-sctp-ipv4-00 that restricts 198 addresses
was never published. These addresses as private addresses should be
allowed to use in SCTP.

As Michael Tuexen suggested, this patch is to move 198 addresses from
unusable to private scope.

Reported-by: Sérgio <surkamp@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: annotate data race around sk_ll_usec

[ Upstream commit 0dbffbb5335a1e3aa6855e4ee317e25e669dd302 ]

sk_ll_usec is read locklessly from sk_can_busy_loop()
while another thread can change its value in sock_setsockopt()

This is correct but needs annotations.

BUG: KCSAN: data-race in __skb_try_recv_datagram / sock_setsockopt

write to 0xffff88814eb5f904 of 4 bytes by task 14011 on cpu 0:
 sock_setsockopt+0x1287/0x2090 net/core/sock.c:1175
 __sys_setsockopt+0x14f/0x200 net/socket.c:2100
 __do_sys_setsockopt net/socket.c:2115 [inline]
 __se_sys_setsockopt net/socket.c:2112 [inline]
 __x64_sys_setsockopt+0x62/0x70 net/socket.c:2112
 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff88814eb5f904 of 4 bytes by task 14001 on cpu 1:
 sk_can_busy_loop include/net/busy_poll.h:41 [inline]
 __skb_try_recv_datagram+0x14f/0x320 net/core/datagram.c:273
 unix_dgram_recvmsg+0x14c/0x870 net/unix/af_unix.c:2101
 unix_seqpacket_recvmsg+0x5a/0x70 net/unix/af_unix.c:2067
 ____sys_recvmsg+0x15d/0x310 include/linux/uio.h:244
 ___sys_recvmsg net/socket.c:2598 [inline]
 do_recvmmsg+0x35c/0x9f0 net/socket.c:2692
 __sys_recvmmsg net/socket.c:2771 [inline]
 __do_sys_recvmmsg net/socket.c:2794 [inline]
 __se_sys_recvmmsg net/socket.c:2787 [inline]
 __x64_sys_recvmmsg+0xcf/0x150 net/socket.c:2787
 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x00000000 -> 0x00000101

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14001 Comm: syz-executor.3 Not tainted 5.13.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/802/garp: fix memleak in garp_request_join()

[ Upstream commit 42ca63f980842918560b25f0244307fd83b4777c ]

I got kmemleak report when doing fuzz test:

BUG: memory leak
unreferenced object 0xffff88810c909b80 (size 64):
  comm "syz", pid 957, jiffies 4295220394 (age 399.090s)
  hex dump (first 32 bytes):
    01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 08 00 00 00 01 02 00 04  ................
  backtrace:
    [<00000000ca1f2e2e>] garp_request_join+0x285/0x3d0
    [<00000000bf153351>] vlan_gvrp_request_join+0x15b/0x190
    [<0000000024005e72>] vlan_dev_open+0x706/0x980
    [<00000000dc20c4d4>] __dev_open+0x2bb/0x460
    [<0000000066573004>] __dev_change_flags+0x501/0x650
    [<0000000035b42f83>] rtnl_configure_link+0xee/0x280
    [<00000000a5e69de0>] __rtnl_newlink+0xed5/0x1550
    [<00000000a5258f4a>] rtnl_newlink+0x66/0x90
    [<00000000506568ee>] rtnetlink_rcv_msg+0x439/0xbd0
    [<00000000b7eaeae1>] netlink_rcv_skb+0x14d/0x420
    [<00000000c373ce66>] netlink_unicast+0x550/0x750
    [<00000000ec74ce74>] netlink_sendmsg+0x88b/0xda0
    [<00000000381ff246>] sock_sendmsg+0xc9/0x120
    [<000000008f6a2db3>] ____sys_sendmsg+0x6e8/0x820
    [<000000008d9c1735>] ___sys_sendmsg+0x145/0x1c0
    [<00000000aa39dd8b>] __sys_sendmsg+0xfe/0x1d0

Calling garp_request_leave() after garp_request_join(), the attr->state
is set to GARP_APPLICANT_VO, garp_attr_destroy() won't be called in last
transmit event in garp_uninit_applicant(), the attr of applicant will be
leaked. To fix this leak, iterate and free each attr of applicant before
rerturning from garp_uninit_applicant().

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/802/mrp: fix memleak in mrp_request_join()

[ Upstream commit 996af62167d0e0ec69b938a3561e96f84ffff1aa ]

I got kmemleak report when doing fuzz test:

BUG: memory leak
unreferenced object 0xffff88810c239500 (size 64):
comm "syz-executor940", pid 882, jiffies 4294712870 (age 14.631s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 01 00 00 00 01 02 00 04 ................
backtrace:
[<00000000a323afa4>] slab_alloc_node mm/slub.c:2972 [inline]
[<00000000a323afa4>] slab_alloc mm/slub.c:2980 [inline]
[<00000000a323afa4>] __kmalloc+0x167/0x340 mm/slub.c:4130
[<000000005034ca11>] kmalloc include/linux/slab.h:595 [inline]
[<000000005034ca11>] mrp_attr_create net/802/mrp.c:276 [inline]
[<000000005034ca11>] mrp_request_join+0x265/0x550 net/802/mrp.c:530
[<00000000fcfd81f3>] vlan_mvrp_request_join+0x145/0x170 net/8021q/vlan_mvrp.c:40
[<000000009258546e>] vlan_dev_open+0x477/0x890 net/8021q/vlan_dev.c:292
[<0000000059acd82b>] __dev_open+0x281/0x410 net/core/dev.c:1609
[<000000004e6dc695>] __dev_change_flags+0x424/0x560 net/core/dev.c:8767
[<00000000471a09af>] rtnl_configure_link+0xd9/0x210 net/core/rtnetlink.c:3122
[<0000000037a4672b>] __rtnl_newlink+0xe08/0x13e0 net/core/rtnetlink.c:3448
[<000000008d5d0fda>] rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3488
[<000000004882fe39>] rtnetlink_rcv_msg+0x369/0xa10 net/core/rtnetlink.c:5552
[<00000000907e6c54>] netlink_rcv_skb+0x134/0x3d0 net/netlink/af_netlink.c:2504
[<00000000e7d7a8c4>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
[<00000000e7d7a8c4>] netlink_unicast+0x4a0/0x6a0 net/netlink/af_netlink.c:1340
[<00000000e0645d50>] netlink_sendmsg+0x78e/0xc90 net/netlink/af_netlink.c:1929
[<00000000c24559b7>] sock_sendmsg_nosec net/socket.c:654 [inline]
[<00000000c24559b7>] sock_sendmsg+0x139/0x170 net/socket.c:674
[<00000000fc210bc2>] ____sys_sendmsg+0x658/0x7d0 net/socket.c:2350
[<00000000be4577b5>] ___sys_sendmsg+0xf8/0x170 net/socket.c:2404

Calling mrp_request_leave() after mrp_request_join(), the attr->state
is set to MRP_APPLICANT_VO, mrp_attr_destroy() won't be called in last
TX event in mrp_uninit_applicant(), the attr of applicant will be leaked.
To fix this leak, iterate and free each attr of applicant before rerturning
from mrp_uninit_applicant().

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

workqueue: fix UAF in pwq_unbound_release_workfn()

commit b42b0bddcbc87b4c66f6497f66fc72d52b712aa7 upstream.

I got a UAF report when doing fuzz test:

[  152.880091][ T8030] ==================================================================
[  152.881240][ T8030] BUG: KASAN: use-after-free in pwq_unbound_release_workfn+0x50/0x190
[  152.882442][ T8030] Read of size 4 at addr ffff88810d31bd00 by task kworker/3:2/8030
[  152.883578][ T8030]
[  152.883932][ T8030] CPU: 3 PID: 8030 Comm: kworker/3:2 Not tainted 5.13.0+ #249
[  152.885014][ T8030] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
[  152.886442][ T8030] Workqueue: events pwq_unbound_release_workfn
[  152.887358][ T8030] Call Trace:
[  152.887837][ T8030]  dump_stack_lvl+0x75/0x9b
[  152.888525][ T8030]  ? pwq_unbound_release_workfn+0x50/0x190
[  152.889371][ T8030]  print_address_description.constprop.10+0x48/0x70
[  152.890326][ T8030]  ? pwq_unbound_release_workfn+0x50/0x190
[  152.891163][ T8030]  ? pwq_unbound_release_workfn+0x50/0x190
[  152.891999][ T8030]  kasan_report.cold.15+0x82/0xdb
[  152.892740][ T8030]  ? pwq_unbound_release_workfn+0x50/0x190
[  152.893594][ T8030]  __asan_load4+0x69/0x90
[  152.894243][ T8030]  pwq_unbound_release_workfn+0x50/0x190
[  152.895057][ T8030]  process_one_work+0x47b/0x890
[  152.895778][ T8030]  worker_thread+0x5c/0x790
[  152.896439][ T8030]  ? process_one_work+0x890/0x890
[  152.897163][ T8030]  kthread+0x223/0x250
[  152.897747][ T8030]  ? set_kthread_struct+0xb0/0xb0
[  152.898471][ T8030]  ret_from_fork+0x1f/0x30
[  152.899114][ T8030]
[  152.899446][ T8030] Allocated by task 8884:
[  152.900084][ T8030]  kasan_save_stack+0x21/0x50
[  152.900769][ T8030]  __kasan_kmalloc+0x88/0xb0
[  152.901416][ T8030]  __kmalloc+0x29c/0x460
[  152.902014][ T8030]  alloc_workqueue+0x111/0x8e0
[  152.902690][ T8030]  __btrfs_alloc_workqueue+0x11e/0x2a0
[  152.903459][ T8030]  btrfs_alloc_workqueue+0x6d/0x1d0
[  152.904198][ T8030]  scrub_workers_get+0x1e8/0x490
[  152.904929][ T8030]  btrfs_scrub_dev+0x1b9/0x9c0
[  152.905599][ T8030]  btrfs_ioctl+0x122c/0x4e50
[  152.906247][ T8030]  __x64_sys_ioctl+0x137/0x190
[  152.906916][ T8030]  do_syscall_64+0x34/0xb0
[  152.907535][ T8030]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[  152.908365][ T8030]
[  152.908688][ T8030] Freed by task 8884:
[  152.909243][ T8030]  kasan_save_stack+0x21/0x50
[  152.909893][ T8030]  kasan_set_track+0x20/0x30
[  152.910541][ T8030]  kasan_set_free_info+0x24/0x40
[  152.911265][ T8030]  __kasan_slab_free+0xf7/0x140
[  152.911964][ T8030]  kfree+0x9e/0x3d0
[  152.912501][ T8030]  alloc_workqueue+0x7d7/0x8e0
[  152.913182][ T8030]  __btrfs_alloc_workqueue+0x11e/0x2a0
[  152.913949][ T8030]  btrfs_alloc_workqueue+0x6d/0x1d0
[  152.914703][ T8030]  scrub_workers_get+0x1e8/0x490
[  152.915402][ T8030]  btrfs_scrub_dev+0x1b9/0x9c0
[  152.916077][ T8030]  btrfs_ioctl+0x122c/0x4e50
[  152.916729][ T8030]  __x64_sys_ioctl+0x137/0x190
[  152.917414][ T8030]  do_syscall_64+0x34/0xb0
[  152.918034][ T8030]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[  152.918872][ T8030]
[  152.919203][ T8030] The buggy address belongs to the object at ffff88810d31bc00
[  152.919203][ T8030]  which belongs to the cache kmalloc-512 of size 512
[  152.921155][ T8030] The buggy address is located 256 bytes inside of
[  152.921155][ T8030]  512-byte region [ffff88810d31bc00, ffff88810d31be00)
[  152.922993][ T8030] The buggy address belongs to the page:
[  152.923800][ T8030] page:ffffea000434c600 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x10d318
[  152.925249][ T8030] head:ffffea000434c600 order:2 compound_mapcount:0 compound_pincount:0
[  152.926399][ T8030] flags: 0x57ff00000010200(slab|head|node=1|zone=2|lastcpupid=0x7ff)
[  152.927515][ T8030] raw: 057ff00000010200 dead000000000100 dead000000000122 ffff888009c42c80
[  152.928716][ T8030] raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
[  152.929890][ T8030] page dumped because: kasan: bad access detected
[  152.930759][ T8030]
[  152.931076][ T8030] Memory state around the buggy address:
[  152.931851][ T8030]  ffff88810d31bc00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  152.932967][ T8030]  ffff88810d31bc80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  152.934068][ T8030] >ffff88810d31bd00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  152.935189][ T8030]                    ^
[  152.935763][ T8030]  ffff88810d31bd80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  152.936847][ T8030]  ffff88810d31be00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  152.937940][ T8030] ==================================================================

If apply_wqattrs_prepare() fails in alloc_workqueue(), it will call put_pwq()
which invoke a work queue to call pwq_unbound_release_workfn() and use the 'wq'.
The 'wq' allocated in alloc_workqueue() will be freed in error path when
apply_wqattrs_prepare() fails. So it will lead a UAF.

CPU0                                          CPU1
alloc_workqueue()
alloc_and_link_pwqs()
apply_wqattrs_prepare() fails
apply_wqattrs_cleanup()
schedule_work(&pwq->unbound_release_work)
kfree(wq)
                                              worker_thread()
                                              pwq_unbound_release_workfn() <- trigger uaf here

If apply_wqattrs_prepare() fails, the new pwq are not linked, it doesn't
hold any reference to the 'wq', 'wq' is invalid to access in the worker,
so add check pwq if linked to fix this.

Fixes: 2d5f0764b526 ("workqueue: split apply_workqueue_attrs() into 3 stages")
Cc: stable@vger.kernel.org # v4.2+
Reported-by: Hulk Robot <hulkci@huawei.com>
Suggested-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Tested-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_unix: fix garbage collect vs MSG_PEEK

commit cbcf01128d0a92e131bd09f1688fe032480b65ca upstream.

unix_gc() assumes that candidate sockets can never gain an external
reference (i.e.  be installed into an fd) while the unix_gc_lock is
held.  Except for MSG_PEEK this is guaranteed by modifying inflight
count under the unix_gc_lock.

MSG_PEEK does not touch any variable protected by unix_gc_lock (file
count is not), yet it needs to be serialized with garbage collection.
Do this by locking/unlocking unix_gc_lock:

 1) increment file count

 2) lock/unlock barrier to make sure incremented file count is visible
    to garbage collection

 3) install file into fd

This is a lock barrier (unlike smp_mb()) that ensures that garbage
collection is run completely before or completely after the barrier.

Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: split out functions related to registering inflight socket files

commit f4e65870e5cede5ca1ec0006b6c9803994e5f7b8 upstream.

We need this functionality for the io_uring file registration, but
we cannot rely on it since CONFIG_UNIX can be modular. Move the helpers
to a separate file, that's always builtin to the kernel if CONFIG_UNIX is
m/y.

No functional changes in this patch, just moving code around.

Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[ backported to older kernels to get access to unix_gc_lock - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: determine if an exception has an error code only when injecting it.

commit b97f074583736c42fb36f2da1164e28c73758912 upstream.

A page fault can be queued while vCPU is in real paged mode on AMD, and
AMD manual asks the user to always intercept it
(otherwise result is undefined).
The resulting VM exit, does have an error code.

Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20210225154135.405125-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftest: fix build error in tools/testing/selftests/vm/userfaultfd.c

When backporting 0db282ba2c12 ("selftest: use mmap instead of
posix_memalign to allocate memory") to this stable branch, I forgot a {
breaking the build.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.241

Link: https://lore.kernel.org/r/20210726153828.144714469@linuxfoundation.org
Link: https://lore.kernel.org/r/20210727061353.216979013@linuxfoundation.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: add xhci_get_virt_ep() helper

[commit b1adc42d440df3233255e313a45ab7e9b2b74096 upstream]

In several event handlers we need to find the right endpoint
structure from slot_id and ep_index in the event.

Add a helper for this, check that slot_id and ep_index are valid.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: spi-fsl-dspi: Fix a resource leak in an error handling path

commit 680ec0549a055eb464dce6ffb4bfb736ef87236e upstream

'dspi_request_dma()' should be undone by a 'dspi_release_dma()' call in the
error handling path of the probe function, as already done in the remove
function

Fixes: 90ba37033cb9 ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/d51caaac747277a1099ba8dea07acd85435b857e.1620587472.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: compression: don't try to compress if we don't have enough pages

commit f2165627319ffd33a6217275e5690b1ab5c45763 upstream

The early check if we should attempt compression does not take into
account the number of input pages. It can happen that there's only one
page, eg. a tail page after some ranges of the BTRFS_MAX_UNCOMPRESSED
have been processed, or an isolated page that won't be converted to an
inline extent.

The single page would be compressed but a later check would drop it
again because the result size must be at least one block shorter than
the input. That can never work with just one page.

CC: stable@vger.kernel.org # 4.4+
Signed-off-by: David Sterba <dsterba@suse.com>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: accel: bma180: Fix BMA25x bandwidth register values

commit 8090d67421ddab0ae932abab5a60200598bf0bbb upstream

According to the BMA253 datasheet [1] and BMA250 datasheet [2] the
bandwidth value for BMA25x should be set as 01xxx:

  "Settings 00xxx result in a bandwidth of 7.81 Hz; [...]
   It is recommended [...] to use the range from ´01000b´ to ´01111b´
   only in order to be compatible with future products."

However, at the moment the drivers sets bandwidth values from 0 to 6,
which is not recommended and always results into 7.81 Hz bandwidth
according to the datasheet.

Fix this by introducing a bw_offset = 8 = 01000b for BMA25x,
so the additional bit is always set for BMA25x.

[1]: https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bma253-ds000.pdf
[2]: https://datasheet.octopart.com/BMA250-Bosch-datasheet-15540103.pdf

Cc: Peter Meerwald <pmeerw@pmeerw.net>
Fixes: 2017cff24cc0 ("iio:bma180: Add BMA250 chip support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210526094408.34298-2-stephan@gerhold.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: accel: bma180: Use explicit member assignment

commit 9436abc40139503a7cea22a96437697d048f31c0 upstream

This uses the C99 explicit .member assignment for the
variant data in struct bma180_part_info. This makes it
easier to understand and add new variants.

Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bcmgenet: ensure EXT_ENERGY_DET_MASK is clear

commit 5a3c680aa2c12c90c44af383fe6882a39875ab81 upstream.

Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.

Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.

Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: Return -ENOTTY for non-drm ioctls

commit 3abab27c322e0f2acf981595aa8040c9164dc9fb upstream.

drm: Return -ENOTTY for non-drm ioctls

Return -ENOTTY from drm_ioctl() when userspace passes in a cmd number
which doesn't relate to the drm subsystem.

Glibc uses the TCGETS ioctl to implement isatty(), and without this
change isatty() returns it incorrectly returns true for drm devices.

To test run this command:
$ if [ -t 0 ]; then echo is a tty; fi < /dev/dri/card0
which shows "is a tty" without this patch.

This may also modify memory which the userspace application is not
expecting.

Signed-off-by: Charles Baylis <cb-kernel@fishzet.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YPG3IBlzaMhfPqCr@stando.fishzet.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftest: use mmap instead of posix_memalign to allocate memory

commit 0db282ba2c12c1515d490d14a1ff696643ab0f1b upstream.

This test passes pointers obtained from anon_allocate_area to the
userfaultfd and mremap APIs.  This causes a problem if the system
allocator returns tagged pointers because with the tagged address ABI
the kernel rejects tagged addresses passed to these APIs, which would
end up causing the test to fail.  To make this test compatible with such
system allocators, stop using the system allocator to allocate memory in
anon_allocate_area, and instead just use mmap.

Link: https://lkml.kernel.org/r/20210714195437.118982-3-pcc@google.com
Link: https://linux-review.googlesource.com/id/Icac91064fcd923f77a83e8e133f8631c5b8fc241
Fixes: c47174fc362a ("userfaultfd: selftest")
Co-developed-by: Lokesh Gidra <lokeshgidra@google.com>
Signed-off-by: Lokesh Gidra <lokeshgidra@google.com>
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Alistair Delva <adelva@google.com>
Cc: William McVicker <willmcvicker@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Mitch Phillips <mitchp@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <stable@vger.kernel.org> [5.4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ixgbe: Fix packet corruption due to missing DMA sync

commit 09cfae9f13d51700b0fecf591dcd658fc5375428 upstream.

When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.

The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.

Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.

Cc: stable@vger.kernel.org
Fixes: 0c5661ecc5dd7 ("ixgbe: fix crash in build_skb Rx code path")
Signed-off-by: Markus Boehme <markubo@amazon.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: ngene: Fix out-of-bounds bug in ngene_command_config_free_buf()

commit 8d4abca95ecc82fc8c41912fa0085281f19cc29f upstream.

Fix an 11-year old bug in ngene_command_config_free_buf() while
addressing the following warnings caught with -Warray-bounds:

arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]

The problem is that the original code is trying to copy 6 bytes of
data into a one-byte size member _config_ of the wrong structue
FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a
legitimate compiler warning because memcpy() overruns the length
of &com.cmd.ConfigureBuffers.config. It seems that the right
structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains
6 more members apart from the header _hdr_. Also, the name of
the function ngene_command_config_free_buf() suggests that the actual
intention is to ConfigureFreeBuffers, instead of ConfigureBuffers
(which takes place in the function ngene_command_config_buf(), above).

Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS
into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as
the destination address, instead of &com.cmd.ConfigureBuffers.config,
when calling memcpy().

This also helps with the ongoing efforts to globally enable
-Warray-bounds and get us closer to being able to tighten the
FORTIFY_SOURCE routines on memcpy().

Link: https://github.com/KSPP/linux/issues/109
Fixes: dae52d009fc9 ("V4L/DVB: ngene: Initial check-in")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/linux-hardening/20210420001631.GA45456@embeddedor/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Fix bug in rb_per_cpu_empty() that might cause deadloop.

commit 67f0d6d9883c13174669f88adac4f0ee656cc16a upstream.

The "rb_per_cpu_empty()" misinterpret the condition (as not-empty) when
"head_page" and "commit_page" of "struct ring_buffer_per_cpu" points to
the same buffer page, whose "buffer_data_page" is empty and "read" field
is non-zero.

An error scenario could be constructed as followed (kernel perspective):

1. All pages in the buffer has been accessed by reader(s) so that all of
them will have non-zero "read" field.

2. Read and clear all buffer pages so that "rb_num_of_entries()" will
return 0 rendering there's no more data to read. It is also required
that the "read_page", "commit_page" and "tail_page" points to the same
page, while "head_page" is the next page of them.

3. Invoke "ring_buffer_lock_reserve()" with large enough "length"
so that it shot pass the end of current tail buffer page. Now the
"head_page", "commit_page" and "tail_page" points to the same page.

4. Discard current event with "ring_buffer_discard_commit()", so that
"head_page", "commit_page" and "tail_page" points to a page whose buffer
data page is now empty.

When the error scenario has been constructed, "tracing_read_pipe" will
be trapped inside a deadloop: "trace_empty()" returns 0 since
"rb_per_cpu_empty()" returns 0 when it hits the CPU containing such
constructed ring buffer. Then "trace_find_next_entry_inc()" always
return NULL since "rb_num_of_entries()" reports there's no more entry
to read. Finally "trace_seq_to_user()" returns "-EBUSY" spanking
"tracing_read_pipe" back to the start of the "waitagain" loop.

I've also written a proof-of-concept script to construct the scenario
and trigger the bug automatically, you can use it to trace and validate
my reasoning above:

  https://github.com/aegistudio/RingBufferDetonator.git

Tests has been carried out on linux kernel 5.14-rc2
(2734d6c1b1a089fb593ef6a23d4b70903526fe0c), my fixed version
of kernel (for testing whether my update fixes the bug) and
some older kernels (for range of affected kernels). Test result is
also attached to the proof-of-concept repository.

Link: https://lore.kernel.org/linux-trace-devel/YPaNxsIlb2yjSi5Y@aegistudio/
Link: https://lore.kernel.org/linux-trace-devel/YPgrN85WL9VyrZ55@aegistudio
Cc: stable@vger.kernel.org
Fixes: bf41a158cacba ("ring-buffer: make reentrant")
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Haoran Luo <www@aegistudio.net>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: gadget: Fix sending zero length packet in DDMA mode.

commit d53dc38857f6dbefabd9eecfcbf67b6eac9a1ef4 upstream.

Sending zero length packet in DDMA mode perform by DMA descriptor
by setting SP (short packet) flag.

For DDMA in function dwc2_hsotg_complete_in() does not need to send
zlp.

Tested by USBCV MSC tests.

Fixes: f71b5e2533de ("usb: dwc2: gadget: fix zero length packet transfers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/967bad78c55dd2db1c19714eee3d0a17cf99d74a.1626777738.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick

commit d6a206e60124a9759dd7f6dfb86b0e1d3b1df82e upstream.

Add the USB serial device ID for the CEL ZigBee EM3588 radio stick.

Signed-off-by: John Keeping <john@metanate.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: cp210x: fix comments for GE CS1000

commit e9db418d4b828dd049caaf5ed65dc86f93bb1a0c upstream.

Fix comments for GE CS1000 CP210x USB ID assignments.

Fixes: 42213a0190b5 ("USB: serial: cp210x: add some more GE USB IDs")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add support for u-blox LARA-R6 family

commit 94b619a07655805a1622484967754f5848640456 upstream.

The patch is meant to support LARA-R6 Cat 1 module family.

Module USB ID:
Vendor  ID: 0x05c6
Product ID: 0x90fA

Interface layout:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: QMI wwan (not available in all versions)

Signed-off-by: Marco De Marco <marco.demarco@posteo.net>
Link: https://lore.kernel.org/r/49260184.kfMIbaSn9k@mars
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: renesas_usbhs: Fix superfluous irqs happen after usb_pkt_pop()

commit 5719df243e118fb343725e8b2afb1637e1af1373 upstream.

This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af32605289e ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.

    renesas_usbhs e6590000.usb: irq_ready run_error 1 : -22

To fix the issue, disable the tx or rx interrupt in usb_pkt_pop().

Fixes: 2743e7f90dc0 ("usb: renesas_usbhs: fix the usb_pkt_pop()")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624122039.596528-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: max-3421: Prevent corruption of freed memory

commit b5fdf5c6e6bee35837e160c00ac89327bdad031b upstream.

The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.

To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.

Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb-storage: Add LaCie Rugged USB3-FW to IGNORE_UAS

commit 6abf2fe6b4bf6e5256b80c5817908151d2d33e9f upstream.

LaCie Rugged USB3-FW appears to be incompatible with UAS. It generates
errors like:
[ 1151.582598] sd 14:0:0:0: tag#16 uas_eh_abort_handler 0 uas-tag 1 inflight: IN
[ 1151.582602] sd 14:0:0:0: tag#16 CDB: Report supported operation codes a3 0c 01 12 00 00 00 00 02 00 00 00
[ 1151.588594] scsi host14: uas_eh_device_reset_handler start
[ 1151.710482] usb 2-4: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 1151.741398] scsi host14: uas_eh_device_reset_handler success
[ 1181.785534] scsi host14: uas_eh_device_reset_handler start

Signed-off-by: Julian Sikorski <belegdol+github@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210720171910.36497-1-belegdol+github@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub: Disable USB 3 device initiated lpm if exit latency is too high

commit 1b7f56fbc7a1b66967b6114d1b5f5a257c3abae6 upstream.

The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.

This is the case for both U1 and U2 sytstem exit latencies and link states.

See USB 3.2 section 9.4.9 "Set Feature" for more details

Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.

If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S: Fix H_RTAS rets buffer overflow

commit f62f3c20647ebd5fb6ecb8f0b477b9281c44c10a upstream.

The kvmppc_rtas_hcall() sets the host rtas_args.rets pointer based on
the rtas_args.nargs that was provided by the guest. That guest nargs
value is not range checked, so the guest can cause the host rets pointer
to be pointed outside the args array. The individual rtas function
handlers check the nargs and nrets values to ensure they are correct,
but if they are not, the handlers store a -3 (0xfffffffd) failure
indication in rets[0] which corrupts host memory.

Fix this by testing up front whether the guest supplied nargs and nret
would exceed the array size, and fail the hcall directly without storing
a failure indication to rets[0].

Also expand on a comment about why we kill the guest and try not to
return errors directly if we have a valid rets[0] pointer.

Fixes: 8e591cb72047 ("KVM: PPC: Book3S: Add infrastructure to implement kernel-side RTAS calls")
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Fix lost USB 2 remote wake

commit 72f68bf5c756f5ce1139b31daae2684501383ad5 upstream.

There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.

When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.

To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.

checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.

If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.

CPU0 CPU1
(hub thread) (xhci event handler)

xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
  clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()

Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread

Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: sb: Fix potential ABBA deadlock in CSP driver

commit 1c2b9519159b470ef24b2638f4794e86e2952ab7 upstream.

SB16 CSP driver may hit potentially a typical ABBA deadlock in two
code paths:

 In snd_sb_csp_stop():
     spin_lock_irqsave(&p->chip->mixer_lock, flags);
     spin_lock(&p->chip->reg_lock);

 In snd_sb_csp_load():
     spin_lock_irqsave(&p->chip->reg_lock, flags);
     spin_lock(&p->chip->mixer_lock);

Also the similar pattern is seen in snd_sb_csp_start().

Although the practical impact is very small (those states aren't
triggered in the same running state and this happens only on a real
hardware, decades old ISA sound boards -- which must be very difficult
to find nowadays), it's a real scenario and has to be fixed.

This patch addresses those deadlocks by splitting the locks in
snd_sb_csp_start() and snd_sb_csp_stop() for avoiding the nested
locks.

Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7b0fcdaf-cd4f-4728-2eae-48c151a92e10@gmail.com
Link: https://lore.kernel.org/r/20210716132723.13216-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/ftrace: fix ftrace_update_ftrace_func implementation

commit f8c2602733c953ed7a16e060640b8e96f9d94b9b upstream.

s390 enforces DYNAMIC_FTRACE if FUNCTION_TRACER is selected.
At the same time implementation of ftrace_caller is not compliant with
HAVE_DYNAMIC_FTRACE since it doesn't provide implementation of
ftrace_update_ftrace_func() and calls ftrace_trace_function() directly.

The subtle difference is that during ftrace code patching ftrace
replaces function tracer via ftrace_update_ftrace_func() and activates
it back afterwards. Unexpected direct calls to ftrace_trace_function()
during ftrace code patching leads to nullptr-dereferences when tracing
is activated for one of functions which are used during code patching.
Those function currently are:
copy_from_kernel_nofault()
copy_from_kernel_nofault_allowed()
preempt_count_sub() [with debug_defconfig]
preempt_count_add() [with debug_defconfig]

Corresponding KASAN report:
 BUG: KASAN: nullptr-dereference in function_trace_call+0x316/0x3b0
 Read of size 4 at addr 0000000000001e08 by task migration/0/15

 CPU: 0 PID: 15 Comm: migration/0 Tainted: G B 5.13.0-41423-g08316af3644d
 Hardware name: IBM 3906 M04 704 (LPAR)
 Stopper: multi_cpu_stop+0x0/0x3e0 <- stop_machine_cpuslocked+0x1e4/0x218
 Call Trace:
  [<0000000001f77caa>] show_stack+0x16a/0x1d0
  [<0000000001f8de42>] dump_stack+0x15a/0x1b0
  [<0000000001f81d56>] print_address_description.constprop.0+0x66/0x2e0
  [<000000000082b0ca>] kasan_report+0x152/0x1c0
  [<00000000004cfd8e>] function_trace_call+0x316/0x3b0
  [<0000000001fb7082>] ftrace_caller+0x7a/0x7e
  [<00000000006bb3e6>] copy_from_kernel_nofault_allowed+0x6/0x10
  [<00000000006bb42e>] copy_from_kernel_nofault+0x3e/0xd0
  [<000000000014605c>] ftrace_make_call+0xb4/0x1f8
  [<000000000047a1b4>] ftrace_replace_code+0x134/0x1d8
  [<000000000047a6e0>] ftrace_modify_all_code+0x120/0x1d0
  [<000000000047a7ec>] __ftrace_modify_code+0x5c/0x78
  [<000000000042395c>] multi_cpu_stop+0x224/0x3e0
  [<0000000000423212>] cpu_stopper_thread+0x33a/0x5a0
  [<0000000000243ff2>] smpboot_thread_fn+0x302/0x708
  [<00000000002329ea>] kthread+0x342/0x408
  [<00000000001066b2>] __ret_from_fork+0x92/0xf0
  [<0000000001fb57fa>] ret_from_fork+0xa/0x30

 The buggy address belongs to the page:
 page:(____ptrval____) refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1
 flags: 0x1ffff00000001000(reserved|node=0|zone=0|lastcpupid=0x1ffff)
 raw: 1ffff00000001000 0000040000000048 0000040000000048 0000000000000000
 raw: 0000000000000000 0000000000000000 ffffffff00000001 0000000000000000
 page dumped because: kasan: bad access detected

 Memory state around the buggy address:
  0000000000001d00: f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7
  0000000000001d80: f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7
 >0000000000001e00: f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7
                       ^
  0000000000001e80: f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7
  0000000000001f00: f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7 f7
 ==================================================================

To fix that introduce ftrace_func callback to be called from
ftrace_caller and update it in ftrace_update_ftrace_func().

Fixes: 4cc9bed034d1 ("[S390] cleanup ftrace backend functions")
Cc: stable@vger.kernel.org
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "MIPS: add PMD table accounting into MIPS'pmd_alloc_one"

This reverts commit 920a42d8b854b1f112aef97a21f0549918889442 which is
commit commit ed914d48b6a1040d1039d371b56273d422c0081e upstream.

Commit b2b29d6d011944 (mm: account PMD tables like PTE tables) is
introduced between v5.9 and v5.10, so this fix (commit 002d8b395fa1)
should NOT apply to any pre-5.10 branch.

Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

proc: Avoid mixing integer types in mem_rw()

[ Upstream commit d238692b4b9f2c36e35af4c6e6f6da36184aeb3e ]

Use size_t when capping the count argument received by mem_rw(). Since
count is size_t, using min_t(int, ...) can lead to a negative value
that will later be passed to access_remote_vm(), which can cause
unexpected behavior.

Since we are capping the value to at maximum PAGE_SIZE, the conversion
from size_t to int when passing it to access_remote_vm() as "len"
shouldn't be a problem.

Link: https://lkml.kernel.org/r/20210512125215.3348316-1-marcelo.cerri@canonical.com
Reviewed-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Souza Cascardo <cascardo@canonical.com>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem"

[ Upstream commit f3a1a937f7b240be623d989c8553a6d01465d04f ]

This reverts commit 0bd860493f81eb2a46173f6f5e44cc38331c8dbd.

While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.

The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.

For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f81 ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: cadence: Correct initialisation of runtime PM again

[ Upstream commit 56912da7a68c8356df6a6740476237441b0b792a ]

The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf98 ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.

Undo 734882a8bf98 ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.

Fixes: 734882a8bf98 ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: target: Fix protect handling in WRITE SAME(32)

[ Upstream commit 6d8e7e7c932162bccd06872362751b0e1d76f5af ]

WRITE SAME(32) command handling reads WRPROTECT at the wrong offset in 1st
byte instead of 10th byte.

Link: https://lore.kernel.org/r/20210702091655.22818-1-d.bogdanov@yadro.com
Fixes: afd73f1b60fc ("target: Perform PROTECT sanity checks for WRITE_SAME")
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: iscsi: Fix iface sysfs attr detection

[ Upstream commit e746f3451ec7f91dcc9fd67a631239c715850a34 ]

A ISCSI_IFACE_PARAM can have the same value as a ISCSI_NET_PARAM so when
iscsi_iface_attr_is_visible tries to figure out the type by just checking
the value, we can collide and return the wrong type. When we call into the
driver we might not match and return that we don't want attr visible in
sysfs. The patch fixes this by setting the type when we figure out what the
param is.

Link: https://lore.kernel.org/r/20210701002559.89533-1-michael.christie@oracle.com
Fixes: 3e0f65b34cc9 ("[SCSI] iscsi_transport: Additional parameters for network settings")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netrom: Decrease sock refcount when sock timers expire

[ Upstream commit 517a16b1a88bdb6b530f48d5d153478b2552d9a8 ]

Commit 63346650c1a9 ("netrom: switch to sock timer API") switched to use
sock timer API. It replaces mod_timer() by sk_reset_timer(), and
del_timer() by sk_stop_timer().

Function sk_reset_timer() will increase the refcount of sock if it is
called on an inactive timer, hence, in case the timer expires, we need to
decrease the refcount ourselves in the handler, otherwise, the sock
refcount will be unbalanced and the sock will never be freed.

Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+10f1194569953b72f1ae@syzkaller.appspotmail.com
Fixes: 63346650c1a9 ("netrom: switch to sock timer API")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: decnet: Fix sleeping inside in af_decnet

[ Upstream commit 5f119ba1d5771bbf46d57cff7417dcd84d3084ba ]

The release_sock() is blocking function, it would change the state
after sleeping. use wait_woken() instead.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: fix uninit-value in caif_seqpkt_sendmsg

[ Upstream commit 991e634360f2622a683b48dfe44fe6d9cb765a09 ]

When nr_segs equal to zero in iovec_from_user, the object
msg->msg_iter.iov is uninit stack memory in caif_seqpkt_sendmsg
which is defined in ___sys_sendmsg. So we cann't just judge
msg->msg_iter.iov->base directlly. We can use nr_segs to judge
msg in caif_seqpkt_sendmsg whether has data buffers.

=====================================================
BUG: KMSAN: uninit-value in caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x220 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
 caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
 sock_sendmsg_nosec net/socket.c:652 [inline]
 sock_sendmsg net/socket.c:672 [inline]
 ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2343
 ___sys_sendmsg net/socket.c:2397 [inline]
 __sys_sendmmsg+0x808/0xc90 net/socket.c:2480
 __compat_sys_sendmmsg net/compat.c:656 [inline]

Reported-by: syzbot+09a5d591c1f98cf5efcb@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=1ace85e8fc9b0d5a45c08c2656c3e91762daa9b8
Fixes: bece7b2398d0 ("caif: Rewritten socket implementation")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/bpf: Perform r1 range checking before accessing jit->seen_reg[r1]

[ Upstream commit 91091656252f5d6d8c476e0c92776ce9fae7b445 ]

Currently array jit->seen_reg[r1] is being accessed before the range
checking of index r1. The range changing on r1 should be performed
first since it will avoid any potential out-of-range accesses on the
array seen_reg[] and also it is more optimal to perform checks on r1
before fetching data from the array. Fix this by swapping the order
of the checks before the array access.

Fixes: 054623105728 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Link: https://lore.kernel.org/bpf/20210715125712.24690-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

liquidio: Fix unintentional sign extension issue on left shift of u16

[ Upstream commit e7efc2ce3d0789cd7c21b70ff00cd7838d382639 ]

Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.

Fix this by casting the u16 values to a u64 before the 29 bit left shift.

Addresses-Coverity: ("Unintended sign extension")

Fixes: 3451b97cce2d ("liquidio: CN23XX register setup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: mediatek: fix fifo rx mode

[ Upstream commit 3a70dd2d050331ee4cf5ad9d5c0a32d83ead9a43 ]

In FIFO mode were two problems:
- RX mode was never handled and
- in this case the tx_buf pointer was NULL and caused an exception

fix this by handling RX mode in mtk_spi_fifo_transfer

Fixes: a568231f4632 ("spi: mediatek: Add spi bus for Mediatek MT8173")
Signed-off-by: Peter Hess <peter.hess@ph-home.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210706121609.680534-1-linux@fw-web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf probe-file: Delete namelist in del_events() on the error path

[ Upstream commit e0fa7ab42232e742dcb3de9f3c1f6127b5adc019 ]

ASan reports some memory leaks when running:

  # perf test "42: BPF filter"

This second leak is caused by a strlist not being dellocated on error
inside probe_file__del_events.

This patch adds a goto label before the deallocation and makes the error
path jump to it.

Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Fixes: e7895e422e4da63d ("perf probe: Split del_perf_probe_events()")
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/174963c587ae77fa108af794669998e4ae558338.1626343282.git.rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf test bpf: Free obj_buf

[ Upstream commit 937654ce497fb6e977a8c52baee5f7d9616302d9 ]

ASan reports some memory leaks when running:

  # perf test "42: BPF filter"

The first of these leaks is caused by obj_buf never being deallocated in
__test__bpf.

This patch adds the missing free.

Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Fixes: ba1fae431e74bb42 ("perf test: Add 'perf test BPF'")
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lore.kernel.org/lkml/60f3ca935fe6672e7e866276ce6264c9e26e4c87.1626343282.git.rickyman7@gmail.com
[ Added missing stdlib.h include ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf lzma: Close lzma stream on exit

[ Upstream commit f8cbb0f926ae1e1fb5f9e51614e5437560ed4039 ]

ASan reports memory leaks when running:

  # perf test "88: Check open filename arg using perf trace + vfs_getname"

One of these is caused by the lzma stream never being closed inside
lzma_decompress_to_file().

This patch adds the missing lzma_end().

Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Fixes: 80a32e5b498a7547 ("perf tools: Add lzma decompression support for kernel module")
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/aaf50bdce7afe996cfc06e1bbb36e4a2a9b9db93.1626343282.git.rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf probe: Fix dso->nsinfo refcounting

[ Upstream commit dedeb4be203b382ba7245d13079bc3b0f6d40c65 ]

ASan reports a memory leak of nsinfo during the execution of:

 # perf test "31: Lookup mmap thread".

The leak is caused by a refcounted variable being replaced without
dropping the refcount.

This patch makes sure that the refcnt of nsinfo is decreased whenever
a refcounted variable is replaced with a new value.

Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Fixes: 544abd44c7064c8a ("perf probe: Allow placing uprobes in alternate namespaces.")
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/55223bc8821b34ccb01f92ef1401c02b6a32e61f.1626343282.git.rickyman7@gmail.com
[ Split from a larger patch ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf map: Fix dso->nsinfo refcounting

[ Upstream commit 2d6b74baa7147251c30a46c4996e8cc224aa2dc5 ]

ASan reports a memory leak of nsinfo during the execution of

  # perf test "31: Lookup mmap thread"

The leak is caused by a refcounted variable being replaced without
dropping the refcount.

This patch makes sure that the refcnt of nsinfo is decreased whenever a
refcounted variable is replaced with a new value.

Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Fixes: bf2e710b3cb8445c ("perf maps: Lookup maps in both intitial mountns and inner mountns.")
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/55223bc8821b34ccb01f92ef1401c02b6a32e61f.1626343282.git.rickyman7@gmail.com
[ Split from a larger patch ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igb: Check if num of q_vectors is smaller than max before array access

[ Upstream commit 6c19d772618fea40d9681f259368f284a330fd90 ]

Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.

Fixes: 047e0030f1e6 ("igb: add new data structure for handling interrupts and NAPI")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Slawomir Laba <slawomirx.laba@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Mateusz Palczewski <mateusz.placzewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iavf: Fix an error handling path in 'iavf_probe()'

[ Upstream commit af30cbd2f4d6d66a9b6094e0aa32420bc8b20e08 ]

If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: 5eae00c57f5e ("i40evf: main driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

e1000e: Fix an error handling path in 'e1000_probe()'

[ Upstream commit 4589075608420bc49fcef6e98279324bf2bb91ae ]

If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: 111b9dc5c981 ("e1000e: add aer support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fm10k: Fix an error handling path in 'fm10k_probe()'

[ Upstream commit e85e14d68f517ef12a5fb8123fff65526b35b6cd ]

If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: 19ae1b3fb99c ("fm10k: Add support for PCI power management and error handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igb: Fix an error handling path in 'igb_probe()'

[ Upstream commit fea03b1cebd653cd095f2e9a58cfe1c85661c363 ]

If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: 40a914fa72ab ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ixgbe: Fix an error handling path in 'ixgbe_probe()'

[ Upstream commit dd2aefcd5e37989ae5f90afdae44bbbf3a2990da ]

If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: 6fabd715e6d8 ("ixgbe: Implement PCIe AER support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igb: Fix use-after-free error during reset

[ Upstream commit 7b292608db23ccbbfbfa50cdb155d01725d7a52e ]

Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.

Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.

(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)

Fixes: 7cc6fd4c60f2 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv6: tcp: drop silly ICMPv6 packet too big messages

commit c7bb4b89033b764eb07db4e060548a6311d801ee upstream.

While TCP stack scales reasonably well, there is still one part that
can be used to DDOS it.

IPv6 Packet too big messages have to lookup/insert a new route,
and if abused by attackers, can easily put hosts under high stress,
with many cpus contending on a spinlock while one is stuck in fib6_run_gc()

ip6_protocol_deliver_rcu()
 icmpv6_rcv()
  icmpv6_notify()
   tcp_v6_err()
    tcp_v6_mtu_reduced()
     inet6_csk_update_pmtu()
      ip6_rt_update_pmtu()
       __ip6_rt_update_pmtu()
        ip6_rt_cache_alloc()
         ip6_dst_alloc()
          dst_alloc()
           ip6_dst_gc()
            fib6_run_gc()
             spin_lock_bh() ...

Some of our servers have been hit by malicious ICMPv6 packets
trying to _increase_ the MTU/MSS of TCP flows.

We believe these ICMPv6 packets are a result of a bug in one ISP stack,
since they were blindly sent back for _every_ (small) packet sent to them.

These packets are for one TCP flow:
09:24:36.266491 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.266509 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316688 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316704 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.608151 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240

TCP stack can filter some silly requests :

1) MTU below IPV6_MIN_MTU can be filtered early in tcp_v6_err()
2) tcp_v6_mtu_reduced() can drop requests trying to increase current MSS.

This tests happen before the IPv6 routing stack is entered, thus
removing the potential contention and route exhaustion.

Note that IPv6 stack was performing these checks, but too late
(ie : after the route has been added, and after the potential
garbage collect war)

v2: fix typo caught by Martin, thanks !
v3: exports tcp_mtu_to_mss(), caught by David, thanks !

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: annotate data races around tp->mtu_info

commit 561022acb1ce62e50f7a8258687a21b84282a4cb upstream.

While tp->mtu_info is read while socket is owned, the write
sides happen from err handlers (tcp_v[46]_mtu_reduced)
which only own the socket spinlock.

Fixes: 563d34d05786 ("tcp: dont drop MTU reduction indications")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dma-buf/sync_file: Don't leak fences on merge failure

commit ffe000217c5068c5da07ccb1c0f8cce7ad767435 upstream.

Each add_fence() call does a dma_fence_get() on the relevant fence.  In
the error path, we weren't calling dma_fence_put() so all those fences
got leaked.  Also, in the krealloc_array failure case, we weren't
freeing the fences array.  Instead, ensure that i and fences are always
zero-initialized and dma_fence_put() all the fences and kfree(fences) on
every error path.

Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Fixes: a02b9dc90d84 ("dma-buf/sync_file: refactor fence storage in struct sync_file")
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624174732.1754546-1-jason@jlekstrand.net
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: validate lwtstate->data before returning from skb_tunnel_info()

commit 67a9c94317402b826fc3db32afc8f39336803d97 upstream.

skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info
type without validation. lwtstate->data can have various types such as
mpls_iptunnel_encap, etc and these are not compatible.
So skb_tunnel_info() should validate before returning that pointer.

Splat looks like:
BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan]
Read of size 2 at addr ffff888106ec2698 by task ping/811

CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195
Call Trace:
 dump_stack_lvl+0x56/0x7b
 print_address_description.constprop.8.cold.13+0x13/0x2ee
 ? vxlan_get_route+0x418/0x4b0 [vxlan]
 ? vxlan_get_route+0x418/0x4b0 [vxlan]
 kasan_report.cold.14+0x83/0xdf
 ? vxlan_get_route+0x418/0x4b0 [vxlan]
 vxlan_get_route+0x418/0x4b0 [vxlan]
 [ ... ]
 vxlan_xmit_one+0x148b/0x32b0 [vxlan]
 [ ... ]
 vxlan_xmit+0x25c5/0x4780 [vxlan]
 [ ... ]
 dev_hard_start_xmit+0x1ae/0x6e0
 __dev_queue_xmit+0x1f39/0x31a0
 [ ... ]
 neigh_xmit+0x2f9/0x940
 mpls_xmit+0x911/0x1600 [mpls_iptunnel]
 lwtunnel_xmit+0x18f/0x450
 ip_finish_output2+0x867/0x2040
 [ ... ]

Fixes: 61adedf3e3f1 ("route: move lwtunnel state to dst_entry")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: send SYNACK packet with accepted fwmark

commit 43b90bfad34bcb81b8a5bc7dc650800f4be1787e upstream.

commit e05a90ec9e16 ("net: reflect mark on tcp syn ack packets")
fixed IPv4 only.

This part is for the IPv6 side.

Fixes: e05a90ec9e16 ("net: reflect mark on tcp syn ack packets")
Signed-off-by: Alexander Ovechkin <ovov@yandex-team.ru>
Acked-by: Dmitry Yakunin <zeil@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ti: fix UAF in tlan_remove_one

commit 0336f8ffece62f882ab3012820965a786a983f70 upstream.

priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.

Fixes: 1e0a8b13d355 ("tlan: cancel work at remove path")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qcom/emac: fix UAF in emac_remove

commit ad297cd2db8953e2202970e9504cab247b6c7cb4 upstream.

adpt is netdev private data and it cannot be
used after free_netdev() call. Using adpt after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.

Fixes: 54e19bc74f33 ("net: qcom/emac: do not use devm on internal phy pdev")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: moxa: fix UAF in moxart_mac_probe

commit c78eaeebe855fd93f2e77142ffd0404a54070d84 upstream.

In case of netdev registration failure the code path will
jump to init_fail label:

init_fail:
netdev_err(ndev, "init failed\n");
moxart_mac_free_memory(ndev);
irq_map_fail:
free_netdev(ndev);
return ret;

So, there is no need to call free_netdev() before jumping
to error handling path, since it can cause UAF or double-free
bug.

Fixes: 6c821bd9edc9 ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bcmgenet: Ensure all TX/RX queues DMAs are disabled

commit 2b452550a203d88112eaf0ba9fc4b750a000b496 upstream.

Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.

Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bridge: sync fdb to new unicast-filtering ports

commit a019abd8022061b917da767cd1a66ed823724eab upstream.

Since commit 2796d0c648c9 ("bridge: Automatically manage
port promiscuous mode.")
bridges with `vlan_filtering 1` and only 1 auto-port don't
set IFF_PROMISC for unicast-filtering-capable ports.

Normally on port changes `br_manage_promisc` is called to
update the promisc flags and unicast filters if necessary,
but it cannot distinguish between *new* ports and ones
losing their promisc flag, and new ports end up not
receiving the MAC address list.

Fix this by calling `br_fdb_sync_static` in `br_add_if`
after the port promisc flags are updated and the unicast
filter was supposed to have been filled.

Fixes: 2796d0c648c9 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: ctnetlink: suspicious RCU usage in ctnetlink_dump_helpinfo

commit c23a9fd209bc6f8c1fa6ee303fdf037d784a1627 upstream.

Two patches listed below removed ctnetlink_dump_helpinfo call from under
rcu_read_lock. Now its rcu_dereference generates following warning:
=============================
WARNING: suspicious RCU usage
5.13.0+ #5 Not tainted
-----------------------------
net/netfilter/nf_conntrack_netlink.c:221 suspicious rcu_dereference_check() usage!

other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
stack backtrace:
CPU: 1 PID: 2251 Comm: conntrack Not tainted 5.13.0+ #5
Call Trace:
 dump_stack+0x7f/0xa1
 ctnetlink_dump_helpinfo+0x134/0x150 [nf_conntrack_netlink]
 ctnetlink_fill_info+0x2c2/0x390 [nf_conntrack_netlink]
 ctnetlink_dump_table+0x13f/0x370 [nf_conntrack_netlink]
 netlink_dump+0x10c/0x370
 __netlink_dump_start+0x1a7/0x260
 ctnetlink_get_conntrack+0x1e5/0x250 [nf_conntrack_netlink]
 nfnetlink_rcv_msg+0x613/0x993 [nfnetlink]
 netlink_rcv_skb+0x50/0x100
 nfnetlink_rcv+0x55/0x120 [nfnetlink]
 netlink_unicast+0x181/0x260
 netlink_sendmsg+0x23f/0x460
 sock_sendmsg+0x5b/0x60
 __sys_sendto+0xf1/0x160
 __x64_sys_sendto+0x24/0x30
 do_syscall_64+0x36/0x70
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: 49ca022bccc5 ("netfilter: ctnetlink: don't dump ct extensions of unconfirmed conntracks")
Fixes: 0b35f6031a00 ("netfilter: Remove duplicated rcu_read_lock.")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv6: fix return value of ip6_skb_dst_mtu

commit 40fc3054b45820c28ea3c65e2c86d041dc244a8a upstream.

Commit 628a5c561890 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE") introduced
ip6_skb_dst_mtu with return value of signed int which is inconsistent
with actually returned values. Also 2 users of this function actually
assign its value to unsigned int variable and only __xfrm6_output
assigns result of this function to signed variable but actually uses
as unsigned in further comparisons and calls. Change this function
to return unsigned int value.

Fixes: 628a5c561890 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/fair: Fix CFS bandwidth hrtimer expiry type

[ Upstream commit 72d0ad7cb5bad265adb2014dbe46c4ccb11afaba ]

The time remaining until expiry of the refresh_timer can be negative.
Casting the type to an unsigned 64-bit value will cause integer
underflow, making the runtime_refresh_within return false instead of
true. These situations are rare, but they do happen.

This does not cause user-facing issues or errors; other than
possibly unthrottling cfs_rq's using runtime from the previous period(s),
making the CFS bandwidth enforcement less strict in those (special)
situations.

Signed-off-by: Odin Ugedal <odin@uged.al>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ben Segall <bsegall@google.com>
Link: https://lore.kernel.org/r/20210629121452.18429-1-odin@uged.al
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: libfc: Fix array index out of bound exception

[ Upstream commit b27c4577557045f1ab3cdfeabfc7f3cd24aca1fe ]

Fix array index out of bound exception in fc_rport_prli_resp().

Link: https://lore.kernel.org/r/20210615165939.24327-1-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: aic7xxx: Fix unintentional sign extension issue on left shift of u8

[ Upstream commit 332a9dd1d86f1e7203fc7f0fd7e82f0b304200fe ]

The shifting of the u8 integer returned fom ahc_inb(ahc, port+3) by 24 bits
to the left will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the event that the top bit of the u8 is set then all then all
the upper 32 bits of the u64 end up as also being set because of the
sign-extension. Fix this by casting the u8 values to a u64 before the 24
bit left shift.

[ This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit f58eb66c0b0a ("Update aic7xxx driver to 6.2.10...") ]

Link: https://lore.kernel.org/r/20210621151727.20667-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unintended sign extension")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: max77686: Do not enforce (incorrect) interrupt trigger type

[ Upstream commit 742b0d7e15c333303daad4856de0764f4bc83601 ]

Interrupt line can be configured on different hardware in different way,
even inverted.  Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.

The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.

The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races.  With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210526172036.183223-6-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

kbuild: mkcompile_h: consider timestamp if KBUILD_BUILD_TIMESTAMP is set

[ Upstream commit a979522a1a88556e42a22ce61bccc58e304cb361 ]

To avoid unnecessary recompilations, mkcompile_h does not regenerate
compile.h if just the timestamp changed.
Though, if KBUILD_BUILD_TIMESTAMP is set, an explicit timestamp for the
build was requested, in which case we should not ignore it.

If a user follows the documentation for reproducible builds [1] and
defines KBUILD_BUILD_TIMESTAMP as the git commit timestamp, a clean
build will have the correct timestamp. A subsequent cherry-pick (or
amend) changes the commit timestamp and if an incremental build is done
with a different KBUILD_BUILD_TIMESTAMP now, that new value is not taken
into consideration. But it should for reproducibility.

Hence, whenever KBUILD_BUILD_TIMESTAMP is explicitly set, do not ignore
UTS_VERSION when making a decision about whether the regenerated version
of compile.h should be moved into place.

[1] https://www.kernel.org/doc/html/latest/kbuild/reproducible-builds.html

Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thermal/core: Correct function name thermal_zone_device_unregister()

[ Upstream commit a052b5118f13febac1bd901fe0b7a807b9d6b51c ]

Fix the following make W=1 kernel build warning:

  drivers/thermal/thermal_core.c:1376: warning: expecting prototype for thermal_device_unregister(). Prototype was for thermal_zone_device_unregister() instead

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210517051020.3463536-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: ls208xa: remove bus-num from dspi node

[ Upstream commit 8240c972c1798ea013cbb407722295fc826b3584 ]

On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:

[   10.471363] couldn't get idr
[   10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[   10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[   10.471708] fsl-dspi: probe of 2100000.spi failed with error -16

Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c33c ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.

Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: juno: Update SCPI nodes as per the YAML schema

[ Upstream commit 70010556b158a0fefe43415fb0c58347dcce7da0 ]

The SCPI YAML schema expects standard node names for clocks and
power domain controllers. Fix those as per the schema for Juno
platforms.

Link: https://lore.kernel.org/r/20210608145133.2088631-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: stm32: fix RCC node name on stm32f429 MCU

[ Upstream commit e4b948415a89a219d13e454011cdcf9e63ecc529 ]

This prevent warning observed with "make dtbs_check W=1"

Warning (simple_bus_reg): /soc/rcc@40023810: simple-bus unit address format
error, expected "40023800"

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: imx: pm-imx5: Fix references to imx5_cpu_suspend_info

[ Upstream commit 89b759469d525f4d5f9c29cd3b1f490311c67f85 ]

The name of the struct, as defined in arch/arm/mach-imx/pm-imx5.c,
is imx5_cpu_suspend_info.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx6: phyFLEX: Fix UART hardware flow control

[ Upstream commit 14cdc1f243d79e0b46be150502b7dba9c5a6bdfd ]

Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.

Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.

Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: BCM63xx: Fix NAND nodes names

[ Upstream commit 75e2f012f6e34b93124d1d86eaa8f27df48e9ea0 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: NSP: dts: fix NAND nodes names

[ Upstream commit 0484594be733d5cdf976f55a2d4e8d887f351b69 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: Cygnus: dts: fix NAND nodes names

[ Upstream commit e256b48a3b07ee1ae4bfa60abbf509ba8e386862 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: brcmstb: dts: fix NAND nodes names

[ Upstream commit 9a800ce1aada6e0f56b78e4713f4858c8990c1f7 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

reset: ti-syscon: fix to_ti_syscon_reset_data macro

[ Upstream commit 05cf8fffcdeb47aef1203c08cbec5224fd3a0e1c ]

The to_ti_syscon_reset_data macro currently only works if the
parameter passed into it is called 'rcdev'.

Fixes a checkpatch --strict issue:

  CHECK: Macro argument reuse 'rcdev' - possible side-effects?
  #53: FILE: drivers/reset/reset-ti-syscon.c:53:
  +#define to_ti_syscon_reset_data(rcdev) \
  + container_of(rcdev, struct ti_syscon_reset_data, rcdev)

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Fix power-controller node names for rk3328

[ Upstream commit 6e6a282b49c6db408d27231e3c709fbdf25e3c1b ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-7-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: rockchip: Fix power-controller node names for rk3288

[ Upstream commit 970cdc53cb1afa73602028c103dbfb6a230080be ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: rockchip: Fix the timer clocks order

[ Upstream commit 7b46d674ac000b101fdad92cf16cc11d90b72f86 ]

Fixed order is the device-tree convention.
The timer driver currently gets clocks by name,
so no changes are needed there.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210506111136.3941-3-ezequiel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: fix pinctrl sleep nodename for rk3399.dtsi

[ Upstream commit a7ecfad495f8af63a5cb332c91f60ab2018897f5 ]

A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.

Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: rockchip: fix pinctrl sleep nodename for rk3036-kylin and rk3288

[ Upstream commit dfbfb86a43f9a5bbd166d88bca9e07ee4e1bff31 ]

A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.

Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288

make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: gemini: add device_type on pci

[ Upstream commit 483f3645b3f7acfd1c78a19d51b80c0656161974 ]

Fixes DT warning on pci node by adding the missing device_type.

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 4.14.240

Link: https://lore.kernel.org/r/20210719144942.861561397@linuxfoundation.org
Link: https://lore.kernel.org/r/20210719184316.271467313@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

seq_file: disallow extremely large seq buffer allocations

commit 8cae8cd89f05f6de223d63e6d15e31c8ba9cf53b upstream.

There is no reasonable need for a buffer larger than this, and it avoids
int overflow pitfalls.

Fixes: 058504edd026 ("fs/seq_file: fallback to vmalloc allocation")
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Qualys Security Advisory <qsa@qualys.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bridge: multicast: fix PIM hello router port marking race

commit 04bef83a3358946bfc98a5ecebd1b0003d83d882 upstream.

When a PIM hello packet is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port the router port list. The multicast lock
protects that list, but it is not acquired in the PIM message case
leading to a race condition, we need to take it to fix the race.

Cc: stable@vger.kernel.org
Fixes: 91b02d3d133b ("bridge: mcast: add router port on PIM hello message")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>