PCI: Set PCI-E Max Payload Size on fabric

On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size.  There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device.  However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.

This can be achieved two ways:

- A conservative approach is to use the smallest common denominator of
  the entire tree below a root complex for every device on that fabric.

This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.

It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.

- A more optimal way is possible, if it falls within a couple of
  constraints:
* The top-level host bridge will never generate packets larger than the
  smallest TLP (or if it can be controlled independently from its MPS at
  least)
* The device will never generate packets larger than MPS (which can be
  configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
  some additional code to specifically deal with that case

Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.

In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.

To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls.  "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.

NOTE: due to the location of the enablement, each arch will need to add
calls to this function.  This patch only enables x86.

This patch includes a number of changes recommended by Benjamin
Herrenschmidt.

Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  CIFS: Cleanup demupltiplex thread exiting code
  CIFS: Move mid search to a separate function
  CIFS: Move RFC1002 check to a separate function
  CIFS: Simplify socket reading in demultiplex thread
  CIFS: Move buffer allocation to a separate function
  cifs: remove unneeded variable initialization in cifs_reconnect_tcon
  cifs: simplify refcounting for oplock breaks
  cifs: fix compiler warning in CIFSSMBQAllEAs
  cifs: fix name parsing in CIFSSMBQAllEAs
  cifs: don't start signing too early
  cifs: trivial: goto out here is unnecessary
  cifs: advertise the right receive buffer size to the server

Merge branch 'gpio/next' of git://git.secretlab.ca/git/linux-2.6

* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
  gpio_msm: Move Qualcomm MSM v2 gpio driver into drivers
  gpio_msm: Move Qualcomm v6 MSM driver into drivers
  msm: gpio: Fold register defs into C file
  msm: gpiomux: Move public API to public header
  msm: gpio: Remove ifdefs on gpio chip registers
  msm: gpio: Remove chip-specific register definitions
  msm: Remove chip-ifdefs for GPIO io mappings
  msm: gpio: Remove unsupported devices
  gpio: ab8500: fix MODULE_ALIAS for ab8500
  of/gpio: export of_gpio_simple_xlate

Merge branch 'for-3.1-rc1' of git://gitorious.org/linux-omap-dss2/linux

* 'for-3.1-rc1' of git://gitorious.org/linux-omap-dss2/linux: (31 commits)
  OMAP: DSS2: HDMI: fix hdmi clock name
  HACK: OMAP: DSS2: clk hack for OMAP2/3
  OMAP: DSS2: DSS: Fix context save/restore
  OMAP: DSS2: DISPC: Fix context save/restore
  OMAP: DSS2: Remove ctx loss count from dss.c
  OMAP: DSS2: Remove unused code from display.c
  OMAP: DSS2: DISPC: remove finegrained clk enables/disables
  OMAP: DSS2: Remove unused opt_clock_available
  OMAP: DSS2: Use PM runtime & HWMOD support
  OMAP: DSS2: Remove CONFIG_OMAP2_DSS_SLEEP_BEFORE_RESET
  OMAP: DSS2: Remove core_dump_clocks
  OMAP: DSS2: DPI: remove unneeded SYSCK enable/disable
  OMAP: DSS2: Use omap_pm_get_dev_context_loss_count to get ctx loss count
  OMAP: DSS2: rewrite use of context_loss_count
  OMAP: DSS2: Remove clk optimization at dss init
  OMAP: DSS2: Fix init and unit sequence
  OMAP: DSS2: Clean up probe for DSS & DSI
  OMAP: DSS2: Handle dpll4_m4_ck in dss_get/put_clocks
  OMAP: DSS2: Fix FIFO threshold and burst size for OMAP4
  OMAP: DSS2: DSI: sync when disabling a display
  ...

Merge branch 'sh-latest' of git://git./linux/kernel/git/lethal/sh-3.x

* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x: (39 commits)
  SH: static should be at beginning of declaration
  sh: move CLKDEV_xxx_ID macro to sh_clk.h
  sh: clock-shx3: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7786: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7785: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7757: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7366: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7343: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7722: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7724: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7366: modify I2C clock settings
  sh: clock-sh7343: modify I2C clock settings
  sh: clock-sh7723: modify I2C clock settings
  sh: clock-sh7722: modify I2C clock settings
  sh: clock-sh7724: modify I2C clock settings
  serial: sh-sci: Fix up pretty name printing for port IRQs.
  serial: sh-sci: Kill off per-port enable/disable callbacks.
  serial: sh-sci: Add missing module description/author bits.
  serial: sh-sci: Regtype probing doesn't need to be fatal.
  sh: Tidy up pre-clkdev clk_get() error handling.
  ...

Merge branch 'msm-move-gpio' of git://codeaurora.org/quic/kernel/davidb/linux-msm into gpio/next

Conflicts:
drivers/gpio/Kconfig
drivers/gpio/Makefile

CIFS: Cleanup demupltiplex thread exiting code

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

CIFS: Move mid search to a separate function

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

CIFS: Move RFC1002 check to a separate function

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

CIFS: Simplify socket reading in demultiplex thread

Move reading to separate function and remove csocket variable.

Also change semantic in a little: goto incomplete_rcv only when
we get -EAGAIN (or a familiar error) while reading rfc1002 header.
In this case we don't check for echo timeout when we don't get whole
header at once, as it was before.

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

CIFS: Move buffer allocation to a separate function

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

gpio_msm: Move Qualcomm MSM v2 gpio driver into drivers

Migrate the driver for the v7-based MSM chips into drivers/gpio.  The
driver is unchanged, only moved.

Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

gpio_msm: Move Qualcomm v6 MSM driver into drivers

Migrate the driver for the v6-based MSM chips into drivers/gpio.  The
driver is unchanged, only moved.

Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

msm: gpio: Fold register defs into C file

No need to have a separate header file containing only register
definitions that are used by a single driver.  Fold these into the
gpio driver.

Signed-off-by: David Brown <davidb@codeaurora.org>

msm: gpiomux: Move public API to public header

The gpiomux.h header contains some SOC ifdefs.  However, the API that
is actually used by the GPIO driver only uses two functions that are
general.  Move these general definitions into a public header file.

Change-Id: Ia5df8af87dba268225598d56908e523bcfc24ef6
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

msm: gpio: Remove ifdefs on gpio chip registers

Select the GPIO register configuration at runtime rather than through
idefs.

Change-Id: I02ea0a3d61bc81669f32097c32420f0688552231
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

msm: gpio: Remove chip-specific register definitions

Put an SOC prefix on each GPIO register definition, eliminating the
need to have SOC ifdefs around the definitions.

Change-Id: I5a01fd328a89ce1be610847934d6e118f5465e42
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

msm: Remove chip-ifdefs for GPIO io mappings

The two GPIO controllers are always mapped to the same virtual address
across all MSM devices.  Instead of selecting this at compile time,
determine the physical address at runtime, eliminating yet something
else preventing multiple MSM targets from being compiled into the same
kernel.

Change-Id: I1672219d978ab6243526adeda6badf49472baa27
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

msm: gpio: Remove unsupported devices

The MSM7x25 and MSM7x27 devices are not yet supported in the kernel.
Remove #ifdef-based tables supporting these chips for now.

Change-Id: I4d9f5abc4cc0942ce75a067097b072489493c1b8
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

OMAP: DSS2: HDMI: fix hdmi clock name

The HDMI clock (hdmi_clk) is missing in the current OMAP4 HWMOD
database. Fix this in the DSS driver by using the old clock name
(dss_48mhz_clk).

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

HACK: OMAP: DSS2: clk hack for OMAP2/3

The HWMOD data for OMAP2 and 3 are currently not up to date regarding
DSS (OMAP4 HWMOD data is fine). This patch makes the DSS driver to get
the opt clocks needed for OMAP2/3 with the old clock names, thus
allowing DSS driver to use runtime PM.

The HWMOD databases should be fixes ASAP, and this patch can be reverted
after that.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Merge branch 'for-next' of git://git./linux/kernel/git/sameo/mfd-2.6

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (46 commits)
  mfd: Fix mismatch in twl4030 mutex lock-unlock
  mfd: twl6030-pwm.c needs MODULE_LICENSE
  mfd: Fix the omap-usb-host clock API usage on usbhs_disable()
  mfd: Acknowledge WM8994 IRQs before reporting
  mfd: Acknowlege all WM831x IRQs before we handle them
  mfd: Avoid two assignments if failures happen in tps65910_i2c_probe
  regulator: Storing tps65912 error codes in u8
  mfd: Don't leak init_data in tps65910_i2c_probe
  regulator: aat2870: Add AAT2870 regulator driver
  backlight: Add AAT2870 backlight driver
  mfd: Add AAT2870 mfd driver
  mfd: Remove dead code from max8997-irq
  mfd: Move TPS55910 Kconfig option
  mfd: Fix missing stmpe kerneldoc
  mfd: Fix off-by-one value range checking for tps65912_i2c_write
  mfd: Add devices for WM831x clocking module
  mfd: Remove comp{1,2}_threshold sysfs entries in tps65911_comparator_remove
  mfd: Don't ask about the TPS65912 core driver in Kconfig
  mfd: Fix off by one in WM831x IRQ code
  mfd: Add tps65921 support from twl-core
  ...

Merge branch 'for-linus' of git://git./linux/kernel/git/geert/linux-m68k

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/math-emu: Remove unnecessary code
  m68k/math-emu: Remove commented out old code
  m68k: Kill warning in setup_arch() when compiling for Sun3
  m68k/atari: Prefix GPIO_{IN,OUT} with CODEC_
  sparc: iounmap() and *_free_coherent() - Use lookup_resource()
  m68k/atari: Reserve some ST-RAM early on for device buffer use
  m68k/amiga: Chip RAM - Use lookup_resource()
  resources: Add lookup_resource()
  sparc: _sparc_find_resource() should check for exact matches
  m68k/amiga: Chip RAM - Offset resource end by CHIP_PHYSADDR
  m68k/amiga: Chip RAM - Use resource_size() to fix off-by-one error
  m68k/amiga: Chip RAM - Change chipavail to an atomic_t
  m68k/amiga: Chip RAM - Always allocate from the start of memory
  m68k/amiga: Chip RAM - Convert from printk() to pr_*()
  m68k/amiga: Chip RAM - Use tabs for indentation

NFS: Re-enable compilation of nfs with !CONFIG_NFS_V4 || !CONFIG_NFS_V4_1

Fix two recently introduced compile problems:

Fix a typo in fs/nfs/pnfs.h

Move the pnfs_blksize declaration outside the CONFIG_NFS_V4 section in
struct nfs_server.

Reported-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mfd: Fix mismatch in twl4030 mutex lock-unlock

A mutex is locked on entry into twl4030_madc_conversion().
Immediate return on some error conditions leaves the
mutex locked.

This patch ensures that mutex is always unlocked before
leaving the function.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: twl6030-pwm.c needs MODULE_LICENSE

twl6030_pwm: module license 'unspecified' taints kernel.

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Hemanth V <hemanthv@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Fix the omap-usb-host clock API usage on usbhs_disable()

usbhs_disable function was invoking clk_enable() instead of
clk_disable(), thus only increasing the clock usage counter and
preventing this particular clock from being ever turned off.
Because of this, the power domain of omap4 the USB Host subsystem
would never reach lower power states.This patch calls clk_disable()
in usbhs_disable function

Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Acknowledge WM8994 IRQs before reporting

This ensures we never have a window where we've handled an interrupt but
not told the hardware about it.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Acknowlege all WM831x IRQs before we handle them

Ensure that we never have a window where we've handled an interrupt (and
therefore need to be notified of new events) but haven't yet told the
interrupt controller that this is the case (so any new events will be
discarded).

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Avoid two assignments if failures happen in tps65910_i2c_probe

In drivers/mfd/tps65910.c:tps65910_i2c_probe() there's potential for a
tiny optimization.

We assign to init_data->irq and init_data->irq_base long before we
need them, and there are two potential exits from the function before
they are needed.

Moving the assignments below these two potential exits means we
completely avoid doing them in these two (failure) cases.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

regulator: Storing tps65912 error codes in u8

get_ctrl_reg() returns -EINVAL so the error handling won't work here
if reg is a u8.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Don't leak init_data in tps65910_i2c_probe

There are a couple of situations where we leak init_data in
drivers/mfd/tps65910.c:tps65910_i2c_probe() - this patch should take
care of them.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

regulator: aat2870: Add AAT2870 regulator driver

Add regulator driver for AnalogicTech AAT2870.

Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

backlight: Add AAT2870 backlight driver

Add backlight driver for AnalogicTech AAT2870.

Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Add AAT2870 mfd driver

Add mfd core driver for AnalogicTech AAT2870.
The AAT2870 is communication through I2C and contains backlight and
regulator components.

Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Remove dead code from max8997-irq

We either hit one of the case's or the default in the switch statement
in get_i2c(), so the 'return ERR_PTR(-EINVAL);' at the end of the
function is just dead code - remove it.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Move TPS55910 Kconfig option

Having another TPS chip at the end of the Kconfig when all it's
relatives are grouped together in their own section seems totally
counter-intuitive. Move it, also in the Makefile.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Fix missing stmpe kerneldoc

Generating kerneldoc for STMPE result in warnings, so fix this by
adding missing documentation.

Signed-off-by: Om Prakash <omprakash.pal@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Fix off-by-one value range checking for tps65912_i2c_write

If bytes == (TPS6591X_MAX_REGISTER + 1), we have a buffer overflow when
doing memcpy(&msg[1], src, bytes).

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Add devices for WM831x clocking module

With the new generic clk API that should appear at some point we should be
able to support the clocking sensibly in Linux.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Remove comp{1,2}_threshold sysfs entries in tps65911_comparator_remove

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Don't ask about the TPS65912 core driver in Kconfig

The user has to select the I2C and SPI drivers individually and they select
the core driver for the device so there's no point in presenting the user
with an option for the core driver.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Fix off by one in WM831x IRQ code

The GPIO IRQs aren't the first IRQs defined, we need to subtract the base
for the GPIOs as well to use them for array indexes.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Add tps65921 support from twl-core

Very similar to TPS65920
List of differences: http://www.ti.com/litv/pdf/swcu066b

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Add WM831x clock control register definitions

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Ensure value written by wm831x_set_bits() is within the mask

Purely for defensiveness.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Implement tps65910 IRQ cleanup

The tps65910_irq_exit() cleanup function was generating a warning from
sparse due to the lack of a prototype. This wasn't causing GCC warnings
as the driver wasn't cleaning up its IRQs on exit at all so there was no
use of an unprototyped function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Add tunnelcreek watchdog to lpc_sch devices

Tunnel Creek has an additional watchdog core.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Clean-up ab8500 register file

This adds a previously undefined test register and removed a
number of double-defined accessory detect registers (they are
already defined higher up in the file.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Update ab8500 subdevice list

This synchronize the subdevice entries for the AB8500 MFD driver
with the latest development of subdrivers for things like battery
charging and temperature monitoring.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: ab8500-core MFD devices marked as initdata

Internal MFD device structs are marked as __devinitdata since the kernel
will allocate memory for the same when calling mfd_add_devices.

Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Reviewed-by: Johan Palsson <johan.palsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

tps65912: add regulator driver

The tps65912 consist of 4 DCDCs and 10 LDOs. The output voltages can be
configured by the SPI or I2C interface, they are meant to supply power
to the main processor and other components.

Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

tps65912: gpio: add gpio driver

TPS65912 has five GPIOs that can be configured for different
purposes.

Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

tps65912: irq: add interrupt controller

This module controls the interrupt handling for the tps65912.
The interrupt sources can be the following:

- GPIO
- PWRON signal
- PWRHOLD signal
- Temperature detection

Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: tps65912: Add new mfd device

The tps65912 chip is a power management IC. It contains the following
components:

- Regulators
- GPIO controller

The core driver is registered as a platform driver, it provides communication
through I2C and SPI interfaces.

Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Use kstrtoul_from_user in ab8500

This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Use kstrtoul_from_user in ab3550

This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Use generic irq chip for jz4740-adc

Use the generic irq chip framework for implementing the irq chip for
the jz4740-adc driver.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Fix error handling if BUG() isn't enabled in WM8994

Even if we would've BUG()ed we should still tidy up after ourselves if that
isn't enabled in the kernel config.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Fix WM8994 IRQ register cache restore on resume

When the byte swap was factored out into the per-register I/O functions
the register restore for the IRQ mask cache (which we use and store in
CPU native format for the interrupt handler) was not updated to do a byte
swap when it uses the bulk I/O. Fix this by writing the cache out one
register at a time.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Support multiple active WM831x AUXADC conversions

The WM831x AUXADC hardware can schedule multiple conversions at once,
allowing higher performance when more than one source is in use as we
can have the hardware start new conversions without having to wait for
a register write.

Take advantage of this in the interrupt driven case, maintaining a list of
callers that are waiting for AUXADC conversions and completing them all
simultaneously. The external interface of the AUXADC is not changed so
there will be limited use of the feature immediately.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Restructure wm8994-core device revision handling

Switch on the device type before revision since anything we do here will
be device as well as revision specific.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Allocate wm835x irq descs dynamically

This allows boards to leave the irq_base field unitialized and
prevents them having to reserve irqs in the platform.
pdata can be optional for irq support now. Without pdata the
driver allocates some free irq range. With pdata and irq_base > 0
the driver allocates exactly the specified irq.
Without pdata the irq defaults to IRQF_TRIGGER_LOW.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Refactor wm831x AUXADC handling into a separate file

In preparation for some additional work on the wm831x AUXADC code move the
support into a separate file. This is a simple code motion patch, there
should be no functional changes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Read wm831x AUXADC conversion results before acknowledging interrupt

Ensure that there's no possibility of loosing an AUXADC interrupt by reading
the conversion result in the IRQ handler when using interrupts. Otherwise
it's possible that under very heavy load a new conversion could be initiated
before the acknowledgement for a previous interrupt has happened.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Support dynamic allocation of IRQ range for wm831x

Use irq_allocate_desc() to get the IRQ range, which turns into a noop on
non-sparse systems. Since all existing users are non-sparse there should
be no compatibility issues.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Only register wm831x RTC device if the 32.768kHz crystal is enabled

The RTC uses the 32.768kHz crystal so if it's not enabled (and it can only
be enabled via OTP or InstantConfig, not runtime software) the RTC can't
function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Allow touchscreen to be disabled on wm831x devices

Allow platform data to flag the touchscreen as disabled so that if the
touch driver is built in we don't end up causing lots of work by spuriously
detecting touchscreen activity on systems where it isn't in use.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Implement support for multiple WM831x devices

Systems using this functionality will be uncommon.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mfd: Fix bus lock interaction for WM831x IRQ set_type() operation

The WM831x IRQ set_type() operation is doing a direct register write when
called but since set_type() is called with the bus lock held this isn't
legal and could cause deadlocks in the IRQ core.

Fix this by posting the updates into an array and syncing in the
bus_sync_unlock() callback.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

cifs: remove unneeded variable initialization in cifs_reconnect_tcon

Reported-and-acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

cifs: simplify refcounting for oplock breaks

Currently, we take a sb->s_active reference and a cifsFileInfo reference
when an oplock break workqueue job is queued. This is unnecessary and
more complicated than it needs to be. Also as Al points out,
deactivate_super has non-trivial locking implications so it's best to
avoid that if we can.

Instead, just cancel any pending oplock breaks for this filehandle
synchronously in cifsFileInfo_put after taking it off the lists.
That should ensure that this job doesn't outlive the structures it
depends on.

Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

cifs: fix compiler warning in CIFSSMBQAllEAs

The recent fix to the above function causes this compiler warning to pop
on some gcc versions:

  CC [M]  fs/cifs/cifssmb.o
fs/cifs/cifssmb.c: In function ‘CIFSSMBQAllEAs’:
fs/cifs/cifssmb.c:5708: warning: ‘ea_name_len’ may be used uninitialized in
this function

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

cifs: fix name parsing in CIFSSMBQAllEAs

The code that matches EA names in CIFSSMBQAllEAs is incorrect. It
uses strncmp to do the comparison with the length limited to the
name_len sent in the response.

Problem: Suppose we're looking for an attribute named "foobar" and
have an attribute before it in the EA list named "foo". The
comparison will succeed since we're only looking at the first 3
characters. Fix this by also comparing the length of the provided
ea_name with the name_len in the response. If they're not equal then
it shouldn't match.

Reported-by: Jian Li <jiali@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

cifs: don't start signing too early

Sniffing traffic on the wire shows that windows clients send a zeroed
out signature field in a NEGOTIATE request, and send "BSRSPYL" in the
signature field during SESSION_SETUP. Make the cifs client behave the
same way.

It doesn't seem to make much difference in any server that I've tested
against, but it's probably best to follow windows behavior as closely as
possible here.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

cifs: trivial: goto out here is unnecessary

...and remove some obsolete comments.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

cifs: advertise the right receive buffer size to the server

Currently, we mirror the same size back to the server that it sends us.
That makes little sense. Instead we should be sending the server the
maximum buffer size that we can handle -- CIFSMaxBufSize minus the
4 byte RFC1001 header.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Merge branch 'nfs-for-3.1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

* 'nfs-for-3.1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (28 commits)
  pnfsblock: write_pagelist handle zero invalid extents
  pnfsblock: note written INVAL areas for layoutcommit
  pnfsblock: bl_write_pagelist
  pnfsblock: bl_read_pagelist
  pnfsblock: cleanup_layoutcommit
  pnfsblock: encode_layoutcommit
  pnfsblock: merge rw extents
  pnfsblock: add extent manipulation functions
  pnfsblock: bl_find_get_extent
  pnfsblock: xdr decode pnfs_block_layout4
  pnfsblock: call and parse getdevicelist
  pnfsblock: merge extents
  pnfsblock: lseg alloc and free
  pnfsblock: remove device operations
  pnfsblock: add device operations
  pnfsblock: basic extent code
  pnfsblock: use pageio_ops api
  pnfsblock: add blocklayout Kconfig option, Makefile, and stubs
  pnfs: cleanup_layoutcommit
  pnfs: ask for layout_blksize and save it in nfs_server
  ...

Merge branch 'for-linus' of git://git./linux/kernel/git/penberg/slab-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slab: use NUMA_NO_NODE
  slab: remove one NR_CPUS dependency

Merge branch 'urgent-for-linus' of git://git./linux/kernel/git/wfg/writeback

* 'urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/writeback:
  don't busy retry the inode on failed grab_super_passive()

Merge git://git.infradead.org/battery-2.6

* git://git.infradead.org/battery-2.6:
  gpio-charger: Fix checking return value of request_any_context_irq
  power_supply: MAX17042: Support additional properties
  max8903_charger: Allow platform data to be __initdata
  power_supply: Add charger driver for MAX8998/LP3974
  power_supply: Add charger driver for MAX8997/8966
  max17042_battery: Remove obsolete cleanup for clientdata
  twl4030_charger: Fix warnings
  wm831x_power: Support multiple instances
  wm831x_backup: Support multiple instances
  apm_power: Fix style error in macros
  s3c_adc_battery: Fix annotation for s3c_adc_battery_probe()
  bq20z75: Enable detection after registering
  bq20z75: Add support for external notification

Merge git://git./linux/kernel/git/brodo/cpupowerutils

* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/cpupowerutils:
  cpupower: Do detect IDA (opportunistic processor performance) via cpuid
  cpupower: Show Intel turbo ratio support via ./cpupower frequency-info
  cpupowerutils: increase MAX_LINE_LEN
  cpupower: Rename package from cpupowerutils to cpupower
  cpupowerutils: Rename: libcpufreq->libcpupower
  cpupowerutils: use kernel version-derived version string
  cpupowerutils: utils - ConfigStyle bugfixes
  cpupowerutils: helpers - ConfigStyle bugfixes
  cpupowerutils: idle_monitor - ConfigStyle bugfixes
  cpupowerutils: lib - ConfigStyle bugfixes
  cpupowerutils: bench - ConfigStyle bugfixes
  cpupowerutils: do not update po files on each and every compile
  cpupowerutils: remove ccdv, use kernel quiet/verbose mechanism
  cpupowerutils: use COPYING, CREDITS from top-level directory
  cpupowerutils - cpufrequtils extended with quite some features

Merge git://git./linux/kernel/git/brodo/pcmcia-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  smc91c92_cs.c: fix bogus compiler warning
  orinoco_cs: be more careful when matching cards with ID 0x0156:0x0002
  hostap_cs: support cards with "Version 01.02" as third product ID
  pcmcia: add PCMCIA_DEVICE_MANF_CARD_PROD_ID3
  pxa2xx pcmcia - stargate 2 use gpio array.
  pcmcia: pxa2xx: remove empty socket_init / socket_resume functions.
  drivers:pcmcia:soc_common: make socket_init and socket_suspend optional

pnfsblock: write_pagelist handle zero invalid extents

For invalid extents, find other pages in the same fsblock and write them out.

[pnfsblock: write_begin]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: note written INVAL areas for layoutcommit

Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: bl_write_pagelist

Note: When upper layer's read/write request cannot be fulfilled, the block
layout driver shouldn't silently mark the page as error. It should do
what can be done and  leave the rest to the upper layer. To do so, we
should set rdata/wdata->res.count properly.

When upper layer re-send the read/write request to finish the rest
part of the request, pgbase is the position where we should start at.

[pnfsblock: bl_write_pagelist support functions]
[pnfsblock: bl_write_pagelist adjust for missing PG_USE_PNFS]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: handle errors when read or write pagelist.]
Signed-off-by: Zhang Jingwang <yyalone@gmail.com>
[pnfs-block: use new write_pagelist api]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
[SQUASHME: pnfsblock: mds_offset is set in the generic layer]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[pnfsblock: mark IO error with NFS_LAYOUT_{RW|RO}_FAILED]
Signed-off-by: Peng Tao <peng_tao@emc.com>
[pnfsblock: SQUASHME: adjust to API change]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: fixup blksize alignment in bl_setup_layoutcommit]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[pnfsblock: bl_write_pagelist adjust for missing PG_USE_PNFS]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: handle errors when read or write pagelist.]
Signed-off-by: Zhang Jingwang <yyalone@gmail.com>
[pnfs-block: use new write_pagelist api]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: bl_read_pagelist

Note: When upper layer's read/write request cannot be fulfilled, the block
layout driver shouldn't silently mark the page as error. It should do
what can be done and  leave the rest to the upper layer. To do so, we
should set rdata/wdata->res.count properly.

When upper layer re-send the read/write request to finish the rest
part of the request, pgbase is the position where we should start at.

[pnfsblock: mark IO error with NFS_LAYOUT_{RW|RO}_FAILED]
Signed-off-by: Peng Tao <peng_tao@emc.com>
[pnfsblock: read path error handling]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: handle errors when read or write pagelist.]
Signed-off-by: Zhang Jingwang <yyalone@gmail.com>
[pnfs-block: use new read_pagelist api]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: cleanup_layoutcommit

In blocklayout driver. There are two things happening
while layoutcommit/cleanup.
1. the modified extents are encoded.
2. On cleanup the extents are put back on the layout rw
   extents list, for reads.

In the new system where actual xdr encoding is done in
encode_layoutcommit() directly into xdr buffer, these are
the new commit stages:

1. On setup_layoutcommit, the range is adjusted as before
   and a structure is allocated for communication with
   bl_encode_layoutcommit && bl_cleanup_layoutcommit
   (Generic layer provides a void-star to hang it on)

2. bl_encode_layoutcommit is called to do the actual
   encoding directly into xdr. The commit-extent-list is not
   freed and is stored on above structure.
   FIXME: The code is not yet converted to the new XDR cleanup

3. On cleanup the commit-extent-list is put back by a call
   to set_to_rw() as before, but with no need for XDR decoding
   of the list as before. And the commit-extent-list is freed.
   Finally allocated structure is freed.

[rm inode and pnfs_layout_hdr args from cleanup_layoutcommit()]
Signed-off-by: Jim Rees <rees@umich.edu>
[pnfsblock: introduce bl_committing list]
Signed-off-by: Peng Tao <peng_tao@emc.com>
[pnfsblock: SQUASHME: adjust to API change]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[blocklayout: encode_layoutcommit implementation]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
[pnfsblock: fix bug setting up layoutcommit.]
Signed-off-by: Tao Guo <guotao@nrchpc.ac.cn>
[pnfsblock: cleanup_layoutcommit wants a status parameter]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: encode_layoutcommit

In blocklayout driver. There are two things happening
while layoutcommit/cleanup.
1. the modified extents are encoded.
2. On cleanup the extents are put back on the layout rw
   extents list, for reads.

In the new system where actual xdr encoding is done in
encode_layoutcommit() directly into xdr buffer, these are
the new commit stages:

1. On setup_layoutcommit, the range is adjusted as before
   and a structure is allocated for communication with
   bl_encode_layoutcommit && bl_cleanup_layoutcommit
   (Generic layer provides a void-star to hang it on)

2. bl_encode_layoutcommit is called to do the actual
   encoding directly into xdr. The commit-extent-list is not
   freed and is stored on above structure.
   FIXME: The code is not yet converted to the new XDR cleanup

3. On cleanup the commit-extent-list is put back by a call
   to set_to_rw() as before, but with no need for XDR decoding
   of the list as before. And the commit-extent-list is freed.
   Finally allocated structure is freed.

[rm inode and pnfs_layout_hdr args from cleanup_layoutcommit()]
[pnfsblock: get rid of deprecated xdr macros]
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[blocklayout: encode_layoutcommit implementation]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
[pnfsblock: fix bug setting up layoutcommit.]
Signed-off-by: Tao Guo <guotao@nrchpc.ac.cn>
[pnfsblock: prevent commit list corruption]
[pnfsblock: fix layoutcommit with an empty opaque]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: merge rw extents

Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: add extent manipulation functions

Adds working implementations of various support functions
to handle INVAL extents, needed by writes, such as
bl_mark_sectors_init and bl_is_sector_init.

[pnfsblock: fix 64-bit compiler warnings for extent manipulation]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[Implement release_inval_marks]
Signed-off-by: Zhang Jingwang <zhangjingwang@nrchpc.ac.cn>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: bl_find_get_extent

Implement bl_find_get_extent(), one of the core extent manipulation
routines.

[pnfsblock: Lookup list entry of layouts and tags in reverse order]
Signed-off-by: Zhang Jingwang <zhangjingwang@nrchpc.ac.cn>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Jim Rees <rees@umich.edu>
pnfsblock: fix print format warnings for sector_t and size_t

gcc spews warnings about these on x86_64, e.g.:
fs/nfs/blocklayout/blocklayout.c:74: warning: format ‘%Lu’ expects type ‘long long unsigned int’, but argument 2 has type ‘sector_t’
fs/nfs/blocklayout/blocklayout.c:388: warning: format ‘%d’ expects type ‘int’, but argument 5 has type ‘size_t’

Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: xdr decode pnfs_block_layout4

XDR decodes the block layout payload sent in LAYOUTGET result, storing
the result in an extent list.

[pnfsblock: get rid of deprecated xdr macros]
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: fix bug getting pnfs_layout_type in translate_devid().]
Signed-off-by: Tao Guo <guotao@nrchpc.ac.cn>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: call and parse getdevicelist

Call GETDEVICELIST during mount, then call and parse GETDEVICEINFO
for each device returned.

[pnfsblock: get rid of deprecated xdr macros]
Signed-off-by: Jim Rees <rees@umich.edu>
[pnfsblock: fix pnfs_deviceid references]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: fix print format warnings for sector_t and size_t]
[pnfs-block: #include <linux/vmalloc.h>]
[pnfsblock: no PNFS_NFS_SERVER]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[pnfsblock: fix bug determining size of striped volume]
[pnfsblock: fix oops when using multiple devices]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[pnfsblock: get rid of vmap and deviceid->area structure]
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: merge extents

Replace a stub, so that extents underlying the layouts are properly
added, merged, or ignored as necessary.

Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: delete the new node before put it]
Signed-off-by: Mingyang Guo <guomingyang@nrchpc.ac.cn>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: lseg alloc and free

Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: fix bug getting pnfs_layout_type in translate_devid().]
Signed-off-by: Tao Guo <guotao@nrchpc.ac.cn>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Zhang Jingwang <Jingwang.Zhang@emc.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: remove device operations

Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[upcall bugfixes]
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: add device operations

Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[upcall bugfixes]
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: basic extent code

Adds structures and basic create/delete code for extents.

Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Zhang Jingwang <Jingwang.Zhang@emc.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

pnfsblock: use pageio_ops api

[pnfsblock: use pnfs_generic_pg_init_read/write]
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>