net/can: add driver for mscan family & mpc52xx_mscan

Taken from socketcan-svn, fixed remaining todos, cleaned up, tested with a
phyCORE-MPC5200B-IO and a custom board.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: convert routing table to RCU

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: put protocols array under RCU

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netiucv: displayed TX bytes value much too high

tx_bytes value must be updated by skb length before skb is freed.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390: remove cu3088 layer for lcs and ctcm

The cu3088-driver used as common base for lcs- and ctcm-devices
makes it difficult to assign the appropriate driver to an lcs-device
or a ctcm-device. This patch eliminates the cu3088-driver and thus
the root device "cu3088". Path /sys/devices/cu3088 is replaced with
the pathes /sys/devices/lcs and /sys/devices/ctcm.

Patch is based on a proposal from Cornelia Huck.

Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ctcm: suspend has to wait for outstanding I/O

State transition to DEV_STATE_STOPPED indicates all outstanding I/O has
finished. Add wait queue to wait for this state.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

iucv: add work_queue cleanup for suspend

If iucv_work_queue is not empty during kernel freeze, a kernel panic
occurs. This suspend-patch adds flushing of the work queue for
pending connection requests and severing of remaining pending
connections.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inetpeer: Optimize inet_getid()

While investigating for network latencies, I found inet_getid() was a
contention point for some workloads, as inet_peer_idlock is shared
by all inet_getid() users regardless of peers.

One way to fix this is to make ip_id_count an atomic_t instead
of __u16, and use atomic_add_return().

In order to keep sizeof(struct inet_peer) = 64 on 64bit arches
tcp_ts_stamp is also converted to __u32 instead of "unsigned long".

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: speedup inet6_dump_addr()

When handling large number of netdevices, inet6_dump_addr()
is very slow because it has O(N^2) complexity.

Instead of scanning one single list, we can use the NETDEV_HASHENTRIES
sub lists of the dev_index hash table, and RCU lookups.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet: fix inet_bind_bucket_for_each

The first "node" is supposed to be the cursor used in the for_each.

The second "node" is ment literally and should not be macro expanded:
it's the name of the hlist_node field from the inet_bind_bucket.

This currently works because when inet_bind_bucket_for_each is called
it's argument is still "node".

Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: speedup inet_dump_ifaddr()

Stephen Hemminger a écrit :
> On Thu, 12 Nov 2009 15:11:36 +0100
> Eric Dumazet <eric.dumazet@gmail.com> wrote:
>
>> When handling large number of netdevices, inet_dump_ifaddr()
>> is very slow because it has O(N^2) complexity.
>>
>> Instead of scanning one single list, we can use the NETDEV_HASHENTRIES
>> sub lists of the dev_index hash table, and RCU lookups.
>>
>> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
>
> You might be able to make RCU critical section smaller by moving
> it into loop.
>

Indeed. But we dump at most one skb (<= 8192 bytes ?), so rcu_read_lock
holding time is small, unless we meet many netdevices without
addresses. I wonder if its really common...

Thanks

[PATCH net-next-2.6] ipv4: speedup inet_dump_ifaddr()

When handling large number of netdevices, inet_dump_ifaddr()
is very slow because it has O(N2) complexity.

Instead of scanning one single list, we can use the NETDEV_HASHENTRIES
sub lists of the dev_index hash table, and RCU lookups.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Make queue pairs on single MSI-X interrupts

This patch pairs similar-numbered Rx and Tx queues onto a single
MSI-X vector.  For example, Tx queue 0 and Rx queue 0's interrupt
with be ethX-RxTx-0.  This allows for more efficient cleanup, since
fewer interrupts will be firing during device operation.  It also
helps with a cleaner CPU affinity for IRQ affinity.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Flush the LSC mask change to prevent repeated interrupts

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: only recycle page if it is on our numa node

This patch makes it so that we only recycle pages when they are from the
local NUMA node.  Non-local pages are freed and replaced with locally
allocated pages.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: check for packets on all tx rings when link is down

We were previously only checking the first tx ring to see if it had any
packets in it when the link when down.  However we should be checking all
of the rings so this patch makes it so that all of the rings are now being
checked.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: removed unused tx/rx total bytes/packets from adapter struct

This patch removes unused variables total_tx_bytes, total_tx_packets,
total_rx_bytes, and total_rx_packets from the adapter struct.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Rework how netdev->stats is handled

This patch does some refactoring work that I felt was needed after reviewing
the changes recently submitted relating to the replacement of net_stats with
netdev->stats.

This patch essentially creates two different collections of stats.  The
first handles the adapter specific states and is stored in gstring_stats,
and the second is for netdev specific stats and is stored in
gstring_net_stats.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: when number of CPUs > 4 combine tx/rx queues to allow more queues

This patch makes it so that nics such as 82576 and newer can support more
hardware queues when there are more than 4 cpus by combining a tx/rx queue
pair onto one interrupt so that 8 queue pairs can be supported and thus
allow for more queues.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: move timesync init into a seperate function

Current code is quite large and making igb_probe difficult to read.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: change type for ring sizes to u16 in igb_set_ring_param

Change the type for the ring size values to u16 and use min/max_t instead of
min/max.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARM: fix bug of checking on signed return value using unsigned statement in w90p910 platform

To fix the bug of checking on signed return value using unsigned statement.
Thanks Roel Kluin for digging out it.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igmp: Use next_net_device_rcu()

We need to use next_det_device_rcu() in RCU protected section.

We also can avoid in_dev_get()/in_dev_put() overhead (code size mainly)
in rcu_read_lock() sections.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: use RCU to walk list of network devices

No longer need read_lock(&dev_base_lock), use RCU instead.
We also can avoid taking references on inet6_dev structs.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: TCP_MSS_DEFAULT, TCP_MSS_DESIRED

Define two symbols needed in both kernel and user space.

Remove old (somewhat incorrect) kernel variant that wasn't used in
most cases.  Default should apply to both RMSS and SMSS (RFC2581).

Replace numeric constants with defined symbols.

Stand-alone patch, originally developed for TCPCT.

Signed-off-by: William.Allen.Simpson@gmail.com
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan/macvlan: propagate transmission state to upper layers

Both vlan and macvlan devices usually don't use a qdisc and immediately
queue packets to the underlying device. Propagate transmission state of
the underlying device to the upper layers so they can react on congestion
and/or inform the sending process.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: allow to propagate errors through ->ndo_hard_start_xmit()

Currently the ->ndo_hard_start_xmit() callbacks are only permitted to return
one of the NETDEV_TX codes. This prevents any kind of error propagation for
virtual devices, like queue congestion of the underlying device in case of
layered devices, or unreachability in case of tunnels.

This patches changes the NET_XMIT codes to avoid clashes with the NETDEV_TX
codes and changes the two callers of dev_hard_start_xmit() to expect either
errno codes, NET_XMIT codes or NETDEV_TX codes as return value.

In case of qdisc_restart(), all non NETDEV_TX codes are mapped to NETDEV_TX_OK
since no error propagation is possible when using qdiscs. In case of
dev_queue_xmit(), the error is propagated upwards.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

niu.c: Use correct length in strncmp

Untested, no hardware

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm: move all compat_ioctl handling to atm/ioctl.c

We have two implementations of the compat_ioctl handling for ATM, the
one that we have had for ages in fs/compat_ioctl.c and the one added to
net/atm/ioctl.c by David Woodhouse. Unfortunately, both versions are
incomplete, and in practice we use a very confusing combination of the
two.

For ioctl numbers that have the same identifier on 32 and 64 bit systems,
we go directly through the compat_ioctl socket operation, for those that

differ, we do a conversion in fs/compat_ioctl.c.

This patch moves both variants into the vcc_compat_ioctl() function,
while preserving the current behaviour. It also kills off the COMPATIBLE_IOCTL
definitions that we never use here.
Doing it this way is clearly not a good solution, but I hope it is a
step into the right direction, so that someone is able to clean up this
mess for real.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/compat: fix dev_ifsioc emulation corner cases

Handling for SIOCSHWTSTAMP is broken on architectures
with a split user/kernel address space like s390,
because it passes a real user pointer while using
set_fs(KERNEL_DS).
A similar problem might arise the next time somebody
adds code to dev_ifsioc.

Split up dev_ifsioc into three separate functions for
SIOCSHWTSTAMP, SIOC*IFMAP and all other numbers so
we can get rid of set_fs in all potentially affected
cases.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Patrick Ohly <patrick.ohly@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

DM9000: Wake on LAN support

Add support for Wake on LAN (WOL) reception and waking the device up from
this signal via the ethtool interface. Currently we are only supporting
the magic-packet variant of wakeup.

WOL is enabled by specifying a second interrupt resource to the driver
which indicates where the interrupt for the WOL is being signalled. This
then enables the necessary ethtool calls to leave the device in a state
to receive WOL frames when going into suspend.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: r_idx not used in ixgbe_msix_clean_rx()

The values of r_idx and rx_ring are not used after the last time they
are set in ixgbe_msix_clean_rx(), so they can be removed.

Signed-off-by: Ali Gholami Rudi <ali@rudi.ir>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

decnet: convert dndev_lock to spinlock

There is no reason for this lock to be reader/writer since
the reader only has lock held for a very brief period.
The overhead of read_lock is more expensive than spinlock.

Compile tested only, I am not a decnet user.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

decnet: add RTNL lock when reading address list

Add missing locking in the case of auto binding to the
default device. The address list might change while this code is looking
at the list.

Compile tested only, I am not a decnet user.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev: fold name hash properly (v3)

The full_name_hash function does not produce well distributed values in
the lower bits, so most code uses hash_32() to fold it.  This is really
a bug introduced when name hashing was added, back in 2.5 when I added
name hashing.

hash_32 is all that is needed since full_name_hash returns unsigned int
which is only 32 bits on 64 bit platforms.

Also, there is no point in using hash_32 on ifindex, because the is naturally
sequential and usually well distributed.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Change version to v1.00.00.23.00.00-01.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Clean up module parameter name.

Change it to match qlge_xxx convention.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Add asic reset to open call.

Force asic to known state at open().

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Do not change frame routing during suspend.

We do not need to change the frame routing to direct all frames to the
management fifo during suspend.  This is now done by the firmware.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clocksource/timecompare: Fix symbol exports to be GPL'd.

Noticed by Thomas GLeixner.

Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: Revive SKB recycling

Before calling gfar_clean_tx_ring() the driver grabs an irqsave
spinlock, and then tries to recycle skbs. But since
skb_recycle_check() returns 0 with IRQs disabled, we'll never
recycle any skbs.

It appears that gfar_clean_tx_ring() and gfar_start_xmit() are
mostly idependent and can work in parallel, except when they
modify num_txbdfree.

So we can drop the lock from most sections and thus fix the skb
recycling.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: Fix race between gfar_error() and gfar_start_xmit()

gfar_error() can arrive at the middle of gfar_start_xmit() processing,
and so it can trigger transfers of BDs that we don't yet expect to
be transmitted.

Fix this by locking the tx queues in gfar_error().

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: Fix thinko in gfar_set_rx_stash_index()

We obviously want to write a modified 'temp' value back to the
register, not the saved IRQ flags.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: Fix build with CONFIG_PM=y

commit fba4ed030cfae7efdb6b79a57b0c5a9d72c9 ("gianfar: Add Multiple
Queue Support") introduced the following build failure:

  CC      gianfar.o
gianfar.c: In function 'gfar_restore':
gianfar.c:1249: error: request for member 'napi' in something not a structure or union

This patch fixes the issue.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: Remove 'Interrupt problem!' warning

It is OK to poll with disabled IRQs, so remove the warning.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

skbuff: Do not allow skb recycling with disabled IRQs

NAPI drivers try to recycle SKBs in their polling routine, but we
generally don't know the context in which the polling will be called,
and the skb recycling itself may require IRQs to be enabled.

This patch adds irqs_disabled() test to the skb_recycle_check()
routine, so that we'll not let the drivers hit the skb recycling
path with IRQs disabled.

As a side effect, this patch actually disables skb recycling for some
[broken] drivers. E.g. gianfar driver grabs an irqsave spinlock during
TX ring processing, and then tries to recycle an skb, and that caused
the following badness:

nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
------------[ cut here ]------------
Badness at kernel/softirq.c:143
NIP: c003e3c4 LR: c423a528 CTR: c003e344
...
NIP [c003e3c4] local_bh_enable+0x80/0xc4
LR [c423a528] destroy_conntrack+0xd4/0x13c [nf_conntrack]
Call Trace:
[c15d1b60] [c003e32c] local_bh_disable+0x1c/0x34 (unreliable)
[c15d1b70] [c423a528] destroy_conntrack+0xd4/0x13c [nf_conntrack]
[c15d1b80] [c02c6370] nf_conntrack_destroy+0x3c/0x70

Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Remove unused var in inet6_dump_ifinfo()

Reported by Stephen Rothwell:

--------------------
Today's linux-next build (x86_64 allmodconfig) produced this warning:

net/ipv6/addrconf.c: In function 'inet6_dump_ifinfo':
net/ipv6/addrconf.c:3833: warning: unused variable 'err'

Introduced by commit 84d2697d9649339215675551eae28ba04068dea1 ("ipv6:
speedup inet6_dump_ifinfo()").
--------------------

Signed-off-by: David S. Miller <davem@davemloft.net>

iwlwifi: fix iwl1000 "RTS/CTS for HT" merge damage

I may have botched my merge conflict resolution instructions for Dave...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
drivers/net/wireless/iwlwifi/iwl-1000.c
drivers/net/wireless/iwlwifi/iwl-6000.c
drivers/net/wireless/iwlwifi/iwl-core.h

CAN: use dev_get_by_index_rcu

Use new function to avoid doing read_lock().

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPV4: use rcu to walk list of devices in IGMP

This also needs to be optimized for large number of devices.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

decnet: use RCU to find network devices

When showing device statistics use RCU rather than read_lock(&dev_base_lock)
Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390: use RCU to walk list of network devices

This is similar to other cases where for_each_netdev_rcu
can be used when gathering information.

By inspection, don't have platform or cross-build environment
to validate.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use rcu for network scheduler API

Use RCU to walk list of network devices in qdisc dump.
This could be optimized for large number of devices.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: eliminate use of dev_base_lock

Do not need to use read_lock(&dev_base_lock), use RCU instead.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev: add netdev_continue_rcu

This adds an RCU macro for continuing search, useful for some
network devices like vlan.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6: use ipv6_addr_v4mapped()

Change udp6_portaddr_hash() to use ipv6_addr_v4mapped()
inline instead of ipv6_addr_type().

Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

parisc: led: Use for_each_netdev_rcu()

Use for_each_netdev_rcu() and dont lock dev_base_lock anymore

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sit: Clean up DF code by copying from IPIP

This patch rearranges the SIT DF bit handling using the new IPIP DF
code.  The only externally visible effect should be the case where
PMTU is enabled and the MTU is exactly 1280 bytes.  In this case the
previous code would send packets out with DF off while the new code
would set the DF bit.  This is inline with RFC 4213.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Allow inet6_dump_addr() to handle more than 64 addresses

Apparently, inet6_dump_addr() is not able to handle more than
64 ipv6 addresses per device. We must break from inner loops
in case skb is full, or else cursor is put at the end of list.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: speedup inet6_dump_ifinfo()

When handling large number of netdevice, inet6_dump_ifinfo()
is very slow because it has O(N^2) complexity.

Instead of scanning one single list, we can use the 256 sub lists
of the dev_index hash table, and RCU lookups.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: netlink_getname, packet_getname -- use DECLARE_SOCKADDR guard

Use guard DECLARE_SOCKADDR in a few more places which allow
us to catch if the structure copied back is too big.

Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

usbnet: Set link down initially for drivers that update link state

Some usbnet drivers update link state while others do not due to
hardware limitations.  Add a flag to distinguish those that do, and
set the link down initially for their devices.

This is intended to fix this bug: http://bugs.debian.org/444043

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

niu: Use DMA_BIT_MASK(44) instead of deprecated DMA_44BIT_MASK

Use DMA_BIT_MASK(44) instead of deprecated DMA_44BIT_MASK

Signed-off-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: bind() optimisation

UDP bind() can be O(N^2) in some pathological cases.

Thanks to secondary hash tables, we can make it O(N)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: version 1.52.1-4

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Change coalescing granularity to 4us

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Remove misleading error print

Failing to allocate MSI-X vectors is not an error and should not be
printed as such

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: GSO implies CSUM offload

Making sure that whenever the FW/HW is configured for GSO, it is also
configured to CSUM offload

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: allocate and copy for pipe TX without sock lock

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: put sockets in a hash table

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

speedfax: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet-cs: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

tms380tr: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

spider-net: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

myri10ge: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: declare MODULE_FIRMWARE

Replace run-time string formatting with preprocessor string
manipulation.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: declare MODULE_FIRMWARE

Replace run-time string formatting with preprocessor string
manipulation.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ambassador: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

solos-pci: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

netx: declare MODULE_FIRMWARE

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

iwlwifi: Fix issue on file transfer stalled in HT mode

Turn on RTS/CTS for HT to prevent uCode TX fifo underrun

This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Use RTS/CTS as the preferred protection mechanism for 6000 series

When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.

The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.

When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.

By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.

For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Libertas: fix issues while configuring host sleep using ethtool wol

Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Libertas: coding style cleanup in ethtool.c

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8187: Fix sparse warnings

Due to a missing header include, sparse generates the following warnings:

  CHECK   drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add LED definition for BenQ Joybook R55v

Setup the GPIOs for the BenQ Joybook netbook.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add LED support for HP Compaq CQ60

Add GPIO configuration for the Compaq CQ60 laptop

Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: don't reset mcast filter when configuring the mode

We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped.  Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: update MAINTAINERS

Although I have always been the active maintainer of the rt2x00 drivers,
I was not mentioned explicitely in the MAINTAINERS file as such.

Update the rt2x00 entry in the MAINTAINERS file to add my name and
email address.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: work around a locking issue in ->set_tim()

ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb-pcmcia: Fix 32bit register access in early bus scanning

The scan function was using 32 bit access which does not
work on 16bit CF cards.

This patch corrects this by doing two 16 bit reads like
ssb_pcmcia_read32 already does.

mb -- Removed locking. That early in init there's no need for locking.

Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
drivers/net/can/usb/ems_usb.c

xfrm: SAD entries do not expire correctly after suspend-resume

  This fixes the following bug in the current implementation of
net/xfrm: SAD entries timeouts do not count the time spent by the machine
in the suspended state. This leads to the connectivity problems because
after resuming local machine thinks that the SAD entry is still valid, while
it has already been expired on the remote server.

  The cause of this is very simple: the timeouts in the net/xfrm are bound to
the old mod_timer() timers. This patch reassigns them to the
CLOCK_REALTIME hrtimer.

  I have been using this version of the patch for a few months on my
machines without any problems. Also run a few stress tests w/o any
issues.

  This version of the patch uses tasklet_hrtimer by Peter Zijlstra
(commit 9ba5f0).

  This patch is against 2.6.31.4. Please CC me.

Signed-off-by: Yury Polyanskiy <polyanskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/compat_ioctl: support SIOCWANDEV

This adds compat_ioctl support for SIOCWANDEV, which has
always been missing.

The definition of struct compat_ifreq was missing an
ifru_settings fields that is needed to support SIOCWANDEV,
so add that and clean up the whitespace damage in the
struct definition.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net, compat_ioctl: fix SIOCGMII ioctls

SIOCGMIIPHY and SIOCGMIIREG return data through ifreq,
so it needs to be converted on the way out as well.

SIOCGIFPFLAGS is unused, but has the same problem in theory.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: multicast RX should increment SNMP/sk_drops counter in allocation failures

When skb_clone() fails, we should increment sk_drops and SNMP counters.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: udp: Optimise multicast reception

IPV6 UDP multicast rx path is a bit complex and can hold a spinlock
for a long time.

Using a small (32 or 64 entries) stack of socket pointers can help
to perform expensive operations (skb_clone(), udp_queue_rcv_skb())
outside of the lock, in most cases.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: udp: Optimise multicast reception

UDP multicast rx path is a bit complex and can hold a spinlock
for a long time.

Using a small (32 or 64 entries) stack of socket pointers can help
to perform expensive operations (skb_clone(), udp_queue_rcv_skb())
outside of the lock, in most cases.

It's also a base for a future RCU conversion of multicast recption.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: udp: optimize unicast RX path

We first locate the (local port) hash chain head
If few sockets are in this chain, we proceed with previous lookup algo.

If too many sockets are listed, we take a look at the secondary
(port, address) hash chain.

We choose the shortest chain and proceed with a RCU lookup on the elected chain.

But, if we chose (port, address) chain, and fail to find a socket on given address,
 we must try another lookup on (port, in6addr_any) chain to find sockets not bound
to a particular IP.

-> No extra cost for typical setups, where the first lookup will probabbly
be performed.

RCU lookups everywhere, we dont acquire spinlock.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>