GitHub/exynos8895/android_kernel_samsung_universal8895.git
10 years agoBluetooth: append new supported device to the list [0b05:17d0]
Andy Shevchenko [Tue, 18 Feb 2014 16:26:20 +0000 (18:26 +0200)]
Bluetooth: append new supported device to the list [0b05:17d0]

The device found on Asus Z87 Expert motherboard requires firmware to work
correctly.

T:  Bus=03 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17d0 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: sort the list of IDs in the source code
Andy Shevchenko [Tue, 18 Feb 2014 16:26:19 +0000 (18:26 +0200)]
Bluetooth: sort the list of IDs in the source code

This will help to manage table of supported IDs.

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: allocate static minor for vhci
Lucas De Marchi [Tue, 18 Feb 2014 05:19:26 +0000 (02:19 -0300)]
Bluetooth: allocate static minor for vhci

Commit bfacbb9 (Bluetooth: Use devname:vhci module alias for virtual HCI
driver) added the module alias to hci_vhci module so it's possible to
create the /dev/vhci node. However creating an alias without
specifying the minor doesn't allow us to create the node ahead,
triggerring module auto-load when it's first accessed.

Starting with depmod from kmod 16 we started to warn if there's a
devname alias without specifying the major and minor.

Let's do the same done for uhid, kvm, fuse and others, specifying a
fixed minor. In systems with systemd as the init the following will
happen: on early boot systemd will call "kmod static-nodes" to read
/lib/modules/$(uname -r)/modules.devname and then create the nodes. When
first accessed these "dead" nodes will trigger the module loading.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add convenience function for fetching IRKs
Johan Hedberg [Tue, 18 Feb 2014 15:14:36 +0000 (17:14 +0200)]
Bluetooth: Add convenience function for fetching IRKs

There are many situations where we need to check if an LE address is an
RPA and if so try to look up the IRK for it. To simplify such cases this
patch adds a convenience function for the job.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix removing any IRKs when unpairing devices
Johan Hedberg [Tue, 18 Feb 2014 15:14:35 +0000 (17:14 +0200)]
Bluetooth: Fix removing any IRKs when unpairing devices

When mgmt_unpair_device is called we should also remove any associated
IRKs. This patch adds a hci_remove_irk convenience function and ensures
that it's called when mgmt_unpair_device is called.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix completing SMP as peripheral when no keys are expected
Johan Hedberg [Tue, 18 Feb 2014 15:14:34 +0000 (17:14 +0200)]
Bluetooth: Fix completing SMP as peripheral when no keys are expected

When we're the acceptors (peripheral/slave) of an SMP procedure and
we've completed distributing our keys we should only stick around
waiting for keys from the remote side if any of the initiator
distribution bits were actually set. This patch fixes the
smp_distribute_keys function to clear the SMP context when this
situation occurs.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix hci_remove_ltk failure when no match is found
Johan Hedberg [Tue, 18 Feb 2014 15:14:33 +0000 (17:14 +0200)]
Bluetooth: Fix hci_remove_ltk failure when no match is found

There is code (in mgmt.c) that depends on the hci_remove_ltk function to
fail if no match is found. This patch adds tracking of removed LTKs
(there can be up to two: one for master and another for slave) in the
hci_remove_ltk function and returns -ENOENT of no matches were found.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove return values from functions that don't need them
Johan Hedberg [Tue, 18 Feb 2014 15:14:32 +0000 (17:14 +0200)]
Bluetooth: Remove return values from functions that don't need them

There are many functions that never fail but still declare an integer
return value for no reason. This patch converts these functions to use a
void return value to avoid any confusion of whether they can fail or not.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix missing address type check for removing LTKs
Johan Hedberg [Tue, 18 Feb 2014 15:14:31 +0000 (17:14 +0200)]
Bluetooth: Fix missing address type check for removing LTKs

When removing Long Term Keys we should also be checking that the given
address type (public vs random) matches. This patch updates the
hci_remove_ltk function to take an extra parameter and uses it for
address type matching.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix properly ignoring unexpected SMP PDUs
Johan Hedberg [Tue, 18 Feb 2014 08:19:37 +0000 (10:19 +0200)]
Bluetooth: Fix properly ignoring unexpected SMP PDUs

If we didn't request certain pieces of information during the key
distribution negotiation we should properly ignore those PDUs if the
peer incorrectly sends them. This includes the Encryption Information
and Master Identification PDUs if the EncKey bit was not set, and the
Identity Information and Identity Address Information PDUs if the IdKey
bit was not set.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Enable support for remote IRK distribution
Johan Hedberg [Tue, 18 Feb 2014 08:19:36 +0000 (10:19 +0200)]
Bluetooth: Enable support for remote IRK distribution

This patch does the necessary changes to request the remote device to
distribute its IRK to us during the SMP pairing procedure. This includes
setting the right key distribution values in the pairing
request/response and handling of the two related SMP PDUs, i.e. Identity
Information and Identity Address Information.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Implement mgmt_load_irks command
Johan Hedberg [Tue, 18 Feb 2014 08:19:35 +0000 (10:19 +0200)]
Bluetooth: Implement mgmt_load_irks command

This patch implements the Load IRKs command for the management
interface. The command is used to load the kernel with the initial set
of IRKs. It also sets a HCI_RPA_RESOLVING flag to indicate that we can
start requesting devices to distribute their IRK to us.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add hci_bdaddr_is_rpa convenience function
Johan Hedberg [Tue, 18 Feb 2014 08:19:34 +0000 (10:19 +0200)]
Bluetooth: Add hci_bdaddr_is_rpa convenience function

When implementing support for Resolvable Private Addresses (RPAs) we'll
need to in several places be able to identify such addresses. This patch
adds a simple convenience function to do the identification of the
address type.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add basic IRK management support
Johan Hedberg [Tue, 18 Feb 2014 08:19:33 +0000 (10:19 +0200)]
Bluetooth: Add basic IRK management support

This patch adds the initial IRK storage and management functions to the
HCI core. This includes storing a list of IRKs per HCI device and the
ability to add, remove and lookup entries in that list.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add AES crypto context for each HCI device
Johan Hedberg [Tue, 18 Feb 2014 08:40:07 +0000 (10:40 +0200)]
Bluetooth: Add AES crypto context for each HCI device

Previously the crypto context has only been available for LE SMP
sessions, but now that we'll need to perform operations also during
discovery it makes sense to have this context part of the hci_dev
struct. Later, the context can be removed from the SMP context.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add smp_irk_matches helper function
Johan Hedberg [Tue, 18 Feb 2014 08:19:31 +0000 (10:19 +0200)]
Bluetooth: Add smp_irk_matches helper function

This patch adds a helper function to check whether a given IRK matches a
given Resolvable Private Address (RPA). The function will be needed for
implementing the rest of address resolving support.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix minor whitespace issues in SMP code
Johan Hedberg [Tue, 18 Feb 2014 08:19:30 +0000 (10:19 +0200)]
Bluetooth: Fix minor whitespace issues in SMP code

This patch fixes a couple of unnecessary empty lines in the SMP code.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix missing PDU length checks for SMP
Johan Hedberg [Tue, 18 Feb 2014 08:19:29 +0000 (10:19 +0200)]
Bluetooth: Fix missing PDU length checks for SMP

For each received SMP PDU we need to check that we have enough data to
fit the specified size of the PDU. This patch adds the necessary checks
for each SMP PDU handler and ensures that buffer overflows do not occur
if to little data has been received.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Allow HCI User Channel usage for controllers without address
Marcel Holtmann [Mon, 17 Feb 2014 17:21:19 +0000 (09:21 -0800)]
Bluetooth: Allow HCI User Channel usage for controllers without address

Trying to setup HCI User Channel usage for LE only controllers without
a public address or configured static address will fail with an error
saying that no address is available.

In case of HCI User Channel the requirement for a valid address is not
needed. So allow skipping this extra validation step.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add missing index added event on user channel failure
Marcel Holtmann [Mon, 17 Feb 2014 17:21:18 +0000 (09:21 -0800)]
Bluetooth: Add missing index added event on user channel failure

When the setup of user channel fails, the index added event is not sent
and will cause issues with user interaction. This problem can be easily
triggered with a LE only controller without a public address. In that
case hci_dev_open() fails and that error case is not sending an event
saying that the controller is available for normal use again.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Fix sending wrong store hint for new long term keys
Marcel Holtmann [Sun, 16 Feb 2014 20:59:06 +0000 (12:59 -0800)]
Bluetooth: Fix sending wrong store hint for new long term keys

The long term keys should only be stored when they belong to an
indentity address. The identity address can either be a public
address or a random static address.

For all other addresses (unresovable or resolvable) tell userspace
that the long term key is not persistent.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Restrict long term keys to public and static addresses
Marcel Holtmann [Sun, 16 Feb 2014 20:59:05 +0000 (12:59 -0800)]
Bluetooth: Restrict long term keys to public and static addresses

The long term keys should be associated with an identity address. Valid
identity addresses are public addresses or static addresses. So only
allow these two as valid address information for long term keys.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: btusb: Add IMC Networks (Broadcom based)
Jurgen Kramer [Sat, 15 Feb 2014 11:01:09 +0000 (12:01 +0100)]
Bluetooth: btusb: Add IMC Networks (Broadcom based)

Add support for IMC Networks (Broadcom based) to btusb driver.

Below the output of /sys/kernel/debug/usb/devices for this device:

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3404 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=240A649F8246
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix write_room() calculation
Peter Hurley [Mon, 10 Feb 2014 01:59:24 +0000 (20:59 -0500)]
Bluetooth: Fix write_room() calculation

The skb truesize of a 12-byte payload with a 10-byte head/tail
reserve is 768 bytes. Consequently, even with 40 tx_credits, at
most 6 packets could be queued at any one time:

  40 tx_credits * 127-byte mtu < 768-byte truesize * 7

This error could also cause the tx queue to apparently stall if
credit flow control is disabled (where tx_credits is fixed at 5),
or if the receiver only granted a limited number of tx credits
(eg., less than 7).

Instead, track the outstanding number of queued packets not yet sent
in wmem_alloc and allow for a maximum of 40 queued packets. Report
the space avail for a single write() as the mtu * number of packets
left before reaching the maximum.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Refactor write_room() calculation
Peter Hurley [Mon, 10 Feb 2014 01:59:23 +0000 (20:59 -0500)]
Bluetooth: Refactor write_room() calculation

Compute the amount of space available for a single write()
within rfcomm_room(); clamp to 0 for negative values. Note
this patch does not change the result of the computation.

Report the amount of room returned in the debug printk.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Don't fail RFCOMM tty writes
Peter Hurley [Mon, 10 Feb 2014 01:59:22 +0000 (20:59 -0500)]
Bluetooth: Don't fail RFCOMM tty writes

The tty driver api design prefers no-fail writes if the driver
write_room() method has previously indicated space is available
to accept writes. Since this is trivially possible for the
RFCOMM tty driver, do so.

Introduce rfcomm_dlc_send_noerror(), which queues but does not
schedule the krfcomm thread if the dlc is not yet connected
(and thus does not error based on the connection state).
The mtu size test is also unnecessary since the caller already
chunks the written data into mtu size.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Force -EIO from tty read/write if .activate() fails
Peter Hurley [Mon, 10 Feb 2014 01:59:21 +0000 (20:59 -0500)]
Bluetooth: Force -EIO from tty read/write if .activate() fails

If rfcomm_dlc_open() fails, set tty into error state which returns
-EIO from reads and writes.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Cleanup RFCOMM device registration error handling
Peter Hurley [Mon, 10 Feb 2014 01:59:20 +0000 (20:59 -0500)]
Bluetooth: Cleanup RFCOMM device registration error handling

If RFCOMM tty device registration fails, cleanup by releasing
the tty_port reference to trigger rfcomm_dev destruction
(rather than open-coding it).

The dlc reference release is moved into rfcomm_dev_add(),
which ensures cleanup in both error paths -- ie., if
__rfcomm_dev_add() fails or if tty_port_register_device() fails.

Fixes releasing the module reference if device registration fails.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Refactor rfcomm_dev_add()
Peter Hurley [Mon, 10 Feb 2014 01:59:19 +0000 (20:59 -0500)]
Bluetooth: Refactor rfcomm_dev_add()

Move rfcomm_dev allocation and initialization into new function,
__rfcomm_dev_add(), to simplify resource release in error handling.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Serialize RFCOMMCREATEDEV and RFCOMMRELEASEDEV ioctls
Peter Hurley [Mon, 10 Feb 2014 01:59:18 +0000 (20:59 -0500)]
Bluetooth: Serialize RFCOMMCREATEDEV and RFCOMMRELEASEDEV ioctls

At least two different race conditions exist with multiple concurrent
RFCOMMCREATEDEV and RFCOMMRELEASEDEV ioctls:
* Multiple concurrent RFCOMMCREATEDEVs with RFCOMM_REUSE_DLC can
  mistakenly share the same DLC.
* RFCOMMRELEASEDEV can destruct the rfcomm_dev still being
  constructed by RFCOMMCREATEDEV.

Introduce rfcomm_ioctl_mutex to serialize these add/remove operations.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Rename __rfcomm_dev_get() to __rfcomm_dev_lookup()
Peter Hurley [Mon, 10 Feb 2014 01:59:17 +0000 (20:59 -0500)]
Bluetooth: Rename __rfcomm_dev_get() to __rfcomm_dev_lookup()

Functions which search lists for matching id's are more
commonly named *_lookup, which is the convention in the
bluetooth core as well.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix RFCOMM parent device for reused dlc
Peter Hurley [Mon, 10 Feb 2014 01:59:16 +0000 (20:59 -0500)]
Bluetooth: Fix RFCOMM parent device for reused dlc

The RFCOMM tty device is parented to the acl link device when
the dlc state_change(BT_CONNECTED) notification is received.
However, if the dlc from the RFCOMM socket is being reused
(RFCOMM_REUSE_DLC is set), then the dlc may already be connected,
and no notification will occur.

Instead, always parent the RFCOMM tty device to the acl link
device at registration time. If the acl link device is not available
(eg, because the dlc is not connected) then the tty will remain
unparented until the BT_CONNECTED notification is received.

Fixes regression with ModemManager when the rfcomm device is
created with the flag RFCOMM_REUSE_DLC.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix unsafe RFCOMM device parenting
Peter Hurley [Mon, 10 Feb 2014 01:59:15 +0000 (20:59 -0500)]
Bluetooth: Fix unsafe RFCOMM device parenting

Accessing the results of hci_conn_hash_lookup_ba() is unsafe without
holding the hci_dev_lock() during the lookup. For example:

CPU 0                             | CPU 1
hci_conn_hash_lookup_ba           | hci_conn_del
  rcu_read_lock                   |   hci_conn_hash_del
  list_for_each_entry_rcu         |     list_del_rcu
    if (.....)                    |       synchronize_rcu
      rcu_read_unlock             |
                                  |   hci_conn_del_sysfs
                                  |   hci_dev_put
                                  |   hci_conn_put
                                  |     put_device (last reference)
                                  |       bt_link_release
                                  |         kfree(conn)
      return p  << just freed     |

Even if a hci_conn reference were taken (via hci_conn_get), would
not guarantee the lifetime of the sysfs device, but only safe
access to the in-memory structure.

Ensure the hci_conn device stays valid while the rfcomm device
is reparented; rename rfcomm_get_device() to rfcomm_reparent_device()
and perform the reparenting within the function while holding the
hci_dev_lock.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Directly close dlc for not yet started RFCOMM session
Peter Hurley [Mon, 10 Feb 2014 01:59:14 +0000 (20:59 -0500)]
Bluetooth: Directly close dlc for not yet started RFCOMM session

If the RFCOMM session has not yet been started (ie., session is
still in BT_BOUND state) when a dlc is closed, directly close and
unlink the dlc rather than sending a DISC frame that is never
sent.

This allows the dlci to be immediately reused rather than waiting
for a 20 second timeout.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Refactor dlc disconnect logic in rfcomm_dlc_close()
Peter Hurley [Mon, 10 Feb 2014 01:59:13 +0000 (20:59 -0500)]
Bluetooth: Refactor dlc disconnect logic in rfcomm_dlc_close()

Prepare for directly closing dlc if the RFCOMM session has not
yet been started; refactor the dlc disconnect logic into a separate
local function, __rfcomm_dlc_disconn(). Retains functional
equivalence.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Refactor deferred setup test in rfcomm_dlc_close()
Peter Hurley [Mon, 10 Feb 2014 01:59:12 +0000 (20:59 -0500)]
Bluetooth: Refactor deferred setup test in rfcomm_dlc_close()

Prepare for directly closing dlc if the RFCOMM session has not
yet been started; refactor the deferred setup test for only those
dlc states to which the test applies. Retains functional
equivalence.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Simplify RFCOMM session state eval
Peter Hurley [Mon, 10 Feb 2014 01:59:11 +0000 (20:59 -0500)]
Bluetooth: Simplify RFCOMM session state eval

Merge conditional test for BT_LISTEN session state into following
switch statement (which is functionally equivalent).

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Verify dlci not in use before rfcomm_dev create
Peter Hurley [Mon, 10 Feb 2014 01:59:10 +0000 (20:59 -0500)]
Bluetooth: Verify dlci not in use before rfcomm_dev create

Only one session/channel combination may be in use at any one
time. However, the failure does not occur until the tty is
opened (in rfcomm_dlc_open()).

Because these settings are actually bound at rfcomm device
creation (via RFCOMMCREATEDEV ioctl), validate and fail before
creating the rfcomm tty device.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix RFCOMM tty teardown race
Peter Hurley [Mon, 10 Feb 2014 01:59:09 +0000 (20:59 -0500)]
Bluetooth: Fix RFCOMM tty teardown race

RFCOMM tty device teardown can race with new tty device registration
for the same device id:

CPU 0                           | CPU 1
rfcomm_dev_add                  | rfcomm_dev_destruct
                                |   spin_lock
                                |   list_del   <== dev_id no longer used
                                |   spin_unlock
  spin_lock                     |     .
  [search rfcomm_dev_list]      |     .
  [dev_id not in use]           |     .
  [initialize new rfcomm_dev]   |     .
  spin_unlock                   |     .
                                |     .
  tty_port_register_device      |   tty_unregister_device

Don't remove rfcomm_dev from the device list until after tty device
unregistration has completed.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix unreleased rfcomm_dev reference
Peter Hurley [Mon, 10 Feb 2014 01:59:08 +0000 (20:59 -0500)]
Bluetooth: Fix unreleased rfcomm_dev reference

When RFCOMM_RELEASE_ONHUP is set, the rfcomm tty driver 'takes over'
the initial rfcomm_dev reference created by the RFCOMMCREATEDEV ioctl.
The assumption is that the rfcomm tty driver will release the
rfcomm_dev reference when the tty is freed (in rfcomm_tty_cleanup()).
However, if the tty is never opened, the 'take over' never occurs,
so when RFCOMMRELEASEDEV ioctl is called, the reference is not
released.

Track the state of the reference 'take over' so that the release
is guaranteed by either the RFCOMMRELEASEDEV ioctl or the rfcomm tty
driver.

Note that the synchronous hangup in rfcomm_release_dev() ensures
that rfcomm_tty_install() cannot race with the RFCOMMRELEASEDEV ioctl.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Release rfcomm_dev only once
Peter Hurley [Mon, 10 Feb 2014 01:59:07 +0000 (20:59 -0500)]
Bluetooth: Release rfcomm_dev only once

No logic prevents an rfcomm_dev from being released multiple
times. For example, if the rfcomm_dev ref count is large due
to pending tx, then multiple RFCOMMRELEASEDEV ioctls may
mistakenly release the rfcomm_dev too many times. Note that
concurrent ioctls are not required to create this condition.

Introduce RFCOMM_DEV_RELEASED status bit which guarantees the
rfcomm_dev can only be released once.

NB: Since the flags are exported to userspace, introduce the status
field to track state for which userspace should not be aware.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Exclude released devices from RFCOMMGETDEVLIST ioctl
Peter Hurley [Mon, 10 Feb 2014 01:59:06 +0000 (20:59 -0500)]
Bluetooth: Exclude released devices from RFCOMMGETDEVLIST ioctl

When enumerating RFCOMM devices in the rfcomm_dev_list, holding
the rfcomm_dev_lock only guarantees the existence of the enumerated
rfcomm_dev in memory, and not safe access to its state. Testing
the device state (such as RFCOMM_TTY_RELEASED) does not guarantee
the device will remain in that state for the subsequent access
to the rfcomm_dev's fields, nor guarantee that teardown has not
commenced.

Obtain an rfcomm_dev reference for the duration of rfcomm_dev
access.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix racy acquire of rfcomm_dev reference
Peter Hurley [Mon, 10 Feb 2014 01:59:05 +0000 (20:59 -0500)]
Bluetooth: Fix racy acquire of rfcomm_dev reference

rfcomm_dev_get() can return a rfcomm_dev reference for a
device for which destruction may be commencing. This can happen
on tty destruction, which calls rfcomm_tty_cleanup(), the last
port reference may have been released but RFCOMM_TTY_RELEASED
was not set. The following race is also possible:

CPU 0                            | CPU 1
                                 | rfcomm_release_dev
rfcomm_dev_get                   |   .
  spin_lock                      |   .
    dev  = __rfcomm_dev_get      |   .
    if dev                       |   .
      if test_bit(TTY_RELEASED)  |   .
                                 |   !test_and_set_bit(TTY_RELEASED)
                                 |     tty_port_put   <<<< last reference
      else                       |
        tty_port_get             |

The reference acquire is bogus because destruction will commence
with the release of the last reference.

Ignore the external state change of TTY_RELEASED and instead rely
on the reference acquire itself to determine if the reference is
valid.

Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agotty: Fix ref counting for port krefs
Peter Hurley [Mon, 10 Feb 2014 01:59:04 +0000 (20:59 -0500)]
tty: Fix ref counting for port krefs

The tty core supports two models for handling tty_port lifetimes;
the tty_port can use the kref supplied by tty_port (which will
automatically destruct the tty_port when the ref count drops to
zero) or it can destruct the tty_port manually.

For tty drivers that choose to use the port kref to manage the
tty_port lifetime, it is not possible to safely acquire a port
reference conditionally. If the last reference is released after
evaluating the condition but before acquiring the reference, a
bogus reference will be held while the tty_port destruction
commences.

Rather, only acquire a port reference if the ref count is non-zero
and allow the caller to distinguish if a reference has successfully
been acquired.

Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoRevert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()"
Peter Hurley [Mon, 10 Feb 2014 01:59:03 +0000 (20:59 -0500)]
Revert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()"

This reverts commit e228b63390536f5b737056059a9a04ea016b1abf.

This is the third of a 3-patch revert, together with
Revert "Bluetooth: Remove rfcomm_carrier_raised()" and
Revert "Bluetooth: Always wait for a connection on RFCOMM open()".

Commit 4a2fb3ecc7467c775b154813861f25a0ddc11aa0,
"Bluetooth: Always wait for a connection on RFCOMM open()" open-codes
blocking on tty open(), rather than using the default behavior
implemented by the tty port.

The reasons for reverting that patch are detailed in that changelog;
this patch restores required functionality for that revert.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoRevert "Bluetooth: Always wait for a connection on RFCOMM open()"
Peter Hurley [Mon, 10 Feb 2014 01:59:02 +0000 (20:59 -0500)]
Revert "Bluetooth: Always wait for a connection on RFCOMM open()"

This reverts commit 4a2fb3ecc7467c775b154813861f25a0ddc11aa0.

This is the second of a 3-patch revert, together with
Revert "Bluetooth: Remove rfcomm_carrier_raised()" and
Revert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()".

Before commit cad348a17e170451ea8688b532a6ca3e98c63b60,
  Bluetooth: Implement .activate, .shutdown and .carrier_raised methods,
tty_port_block_til_ready() was open-coded in rfcomm_tty_install() as
part of the RFCOMM tty open().

Unfortunately, it did not implement non-blocking open nor CLOCAL open,
but rather always blocked for carrier. This is not the expected or
typical behavior for ttys, and prevents several common terminal
programming idioms from working (eg., opening in non-blocking
mode to initialize desired termios settings then re-opening for
connection).

Commit cad348a17e170451ea8688b532a6ca3e98c63b60,
  Bluetooth: Implement .activate, .shutdown and .carrier_raised methods,
added the necessary tty_port methods to use the default tty_port_open().
However, this triggered two important user-space regressions.

The first regression involves the complicated mechanism for reparenting
the rfcomm tty device to the ACL link device which represents an
open link to a specific bluetooth host. This regression causes ModemManager
to conclude the rfcomm tty device does not front a modem so it makes
no attempt to initialize an attached modem. This regression is
caused by the lack of a device_move() if the dlc is already open (and
not specifically related to the open-coded block_til_ready()).

A more appropriate solution is submitted in
"Bluetooth: Fix unsafe RFCOMM device parenting" and
"Bluetooth: Fix RFCOMM parent device for reused dlc"

The second regression involves "rfcomm bind" and wvdial (a ppp dialer).
rfcomm bind creates a device node for a /dev/rfcomm<n>. wvdial opens
that device in non-blocking mode (because it expects the connection
to have already been established). In addition, subsequent writes
to the rfcomm tty device fail (because the link is not yet connected;
rfcomm connection begins with the actual tty open()).

However, restoring the original behavior (in the patch which
this reverts) was undesirable.

Firstly, the original reporter notes that a trivial userspace
"workaround" already exists: rfcomm connect, which creates the
device node and establishes the expected connection.

Secondly, the failed writes occur because the rfcomm tty driver
does not buffer writes to an unconnected device; this contrasts with
the dozen of other tty drivers (in fact, all of them) that do just
that. The submitted patch "Bluetooth: Don't fail RFCOMM tty writes"
corrects this.

Thirdly, it was a long-standing bug to block on non-blocking open,
which is re-fixed by revert.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoRevert "Bluetooth: Remove rfcomm_carrier_raised()"
Peter Hurley [Mon, 10 Feb 2014 01:59:01 +0000 (20:59 -0500)]
Revert "Bluetooth: Remove rfcomm_carrier_raised()"

This reverts commit f86772af6a0f643d3e13eb3f4f9213ae0c333ee4.

This is the first of a 3-patch revert, together with
Revert "Bluetooth: Always wait for a connection on RFCOMM open()" and
Revert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()".

Commit 4a2fb3ecc7467c775b154813861f25a0ddc11aa0,
"Bluetooth: Always wait for a connection on RFCOMM open()" open-codes
blocking on tty open(), rather than using the default behavior
implemented by the tty port.

The reasons for reverting that patch are detailed in that changelog;
this patch restores required functionality for that revert.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Enable LE L2CAP CoC support by default
Johan Hedberg [Fri, 14 Feb 2014 05:40:51 +0000 (07:40 +0200)]
Bluetooth: Enable LE L2CAP CoC support by default

Now that the LE L2CAP Connection Oriented Channel support has undergone a
decent amount of testing we can make it officially supported. This patch
removes the enable_lecoc module parameter which was previously needed to
enable support for LE L2CAP CoC.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Use connection parameters if any
Andre Guedes [Mon, 3 Feb 2014 16:56:19 +0000 (13:56 -0300)]
Bluetooth: Use connection parameters if any

This patch changes hci_connect_le() so it uses the connection
parameters specified for the certain device. If no parameters
were configured, we use the default values.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Introduce connection parameters list
Andre Guedes [Mon, 3 Feb 2014 16:56:18 +0000 (13:56 -0300)]
Bluetooth: Introduce connection parameters list

This patch adds to hdev the connection parameters list (hdev->le_
conn_params). The elements from this list (struct hci_conn_params)
contains the connection parameters (for now, minimum and maximum
connection interval) that should be used during the connection
establishment.

Moreover, this patch adds helper functions to manipulate hdev->le_
conn_params list. Some of these functions are also declared in
hci_core.h since they will be used outside hci_core.c in upcoming
patches.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add constants for LTK key types
Marcel Holtmann [Sat, 1 Feb 2014 03:02:30 +0000 (19:02 -0800)]
Bluetooth: Add constants for LTK key types

The LTK key types available right now are unauthenticated and
authenticated ones. Provide two simple constants for it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Track if link is using P-256 authenticated combination key
Marcel Holtmann [Sat, 1 Feb 2014 19:52:02 +0000 (11:52 -0800)]
Bluetooth: Track if link is using P-256 authenticated combination key

When the ACL link is using P-256 authenticated combination key, mark
the link mode as HCI_LM_FIPS.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Include security level 4 in connections check
Marcel Holtmann [Sat, 1 Feb 2014 19:32:25 +0000 (11:32 -0800)]
Bluetooth: Include security level 4 in connections check

This check is only used for RFCOMM connections and most likely no
RFCOMM based profile will require security level 4 secure connection
security policy. In case it ever does make sure that seucrity level 4
is treated as sufficient security level.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add management command for Secure Connection Only Mode
Marcel Holtmann [Sat, 1 Feb 2014 17:19:57 +0000 (09:19 -0800)]
Bluetooth: Add management command for Secure Connection Only Mode

With support for Secure Connections it is possible to switch the
controller into a mode that is called Secure Connections Only. In
this mode only security level 4 connections are allowed (with the
exception of security level 0 approved services).

This patch just introduces the management command and setting of the
right internal flags to enable this mode. It does not yet enforce it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Remove __packed from struct smp_ltk
Marcel Holtmann [Sat, 1 Feb 2014 02:42:18 +0000 (18:42 -0800)]
Bluetooth: Remove __packed from struct smp_ltk

The struct smp_ltk does not need to be packed and so remove __packed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Rename authentication to key_type in mgmt_ltk_info
Marcel Holtmann [Sat, 1 Feb 2014 02:42:17 +0000 (18:42 -0800)]
Bluetooth: Rename authentication to key_type in mgmt_ltk_info

The field is not a boolean, it is actually a field for a key type. So
name it properly.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Remove check for valid LTK authenticated parameter
Marcel Holtmann [Sat, 1 Feb 2014 02:42:16 +0000 (18:42 -0800)]
Bluetooth: Remove check for valid LTK authenticated parameter

The LTK authenticated parameter is the key type of the LTK and similar
to link keys there is no need to check the currently supported values.

For possible future improvements, the kernel will only use key types
it knows about and just ignore all the other ones.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Track the AES-CCM encryption status of LE and BR/EDR links
Marcel Holtmann [Sat, 1 Feb 2014 00:24:28 +0000 (16:24 -0800)]
Bluetooth: Track the AES-CCM encryption status of LE and BR/EDR links

When encryption for LE links has been enabled, it will always be use
AES-CCM encryption. In case of BR/EDR Secure Connections, the link
will also use AES-CCM encryption. In both cases track the AES-CCM
status in the connection flags.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Remove one level of indentation from hci_encrypt_change_evt
Marcel Holtmann [Sat, 1 Feb 2014 00:24:27 +0000 (16:24 -0800)]
Bluetooth: Remove one level of indentation from hci_encrypt_change_evt

The function already has an unlock label which means the one extra level
on indentation is not useful and just makes the code more complex. So
remove it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Remove use_debug_keys debugfs entry
Marcel Holtmann [Fri, 31 Jan 2014 19:55:23 +0000 (11:55 -0800)]
Bluetooth: Remove use_debug_keys debugfs entry

Since the use of debug keys can now be identified from the current
settings information, this debugfs entry is no longer necessary.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add management command to allow use of debug keys
Marcel Holtmann [Fri, 31 Jan 2014 19:55:22 +0000 (11:55 -0800)]
Bluetooth: Add management command to allow use of debug keys

Originally allowing the use of debug keys was done via the Load Link
Keys management command. However this is BR/EDR specific and to be
flexible and allow extending this to LE as well, make this an independent
command.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add management setting for use of debug keys
Marcel Holtmann [Fri, 31 Jan 2014 19:55:21 +0000 (11:55 -0800)]
Bluetooth: Add management setting for use of debug keys

When the controller has been enabled to allow usage of debug keys, then
clearly identify that in the current settings information.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Introduce le_conn_failed() helper
Andre Guedes [Thu, 30 Jan 2014 21:22:08 +0000 (18:22 -0300)]
Bluetooth: Introduce le_conn_failed() helper

This patch moves connection attempt failure code to its own function
so it can be reused in the next patch.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Group list_head fields from strcut hci_dev together
Andre Guedes [Thu, 30 Jan 2014 21:22:05 +0000 (18:22 -0300)]
Bluetooth: Group list_head fields from strcut hci_dev together

This patch groups the list_head fields from struct hci_dev together
and removes empty lines between them.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Save connection interval parameters in hci_conn
Andre Guedes [Thu, 30 Jan 2014 21:22:04 +0000 (18:22 -0300)]
Bluetooth: Save connection interval parameters in hci_conn

This patch creates two new fields in struct hci_conn to save the
minimum and maximum connection interval values used to establish
the connection this object represents.

This change is required in order to know what parameters the
connection is currently using.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix differentiating stored master vs slave LTK types
Johan Hedberg [Fri, 31 Jan 2014 03:40:00 +0000 (19:40 -0800)]
Bluetooth: Fix differentiating stored master vs slave LTK types

If LTK distribution happens in both directions we will have two LTKs for
the same remote device: one which is used when we're connecting as
master and another when we're connecting as slave. When looking up LTKs
from the locally stored list we shouldn't blindly return the first match
but also consider which type of key is in question. If we do not do this
we may end up selecting an incorrect encryption key for a connection.

This patch fixes the issue by always specifying to the LTK lookup
functions whether we're looking for a master or a slave key.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove unnecessary LTK type check from hci_add_ltk
Johan Hedberg [Fri, 31 Jan 2014 03:39:59 +0000 (19:39 -0800)]
Bluetooth: Remove unnecessary LTK type check from hci_add_ltk

All callers of hci_add_ltk pass a valid value to it. There are no places
where e.g. user space, the controller or the remote peer would be able
to cause invalid values to be passed. Therefore, just remove the
potentially confusing check from the beginning of the function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Make LTK key type check more readable
Johan Hedberg [Fri, 31 Jan 2014 03:39:58 +0000 (19:39 -0800)]
Bluetooth: Make LTK key type check more readable

Instead of magic bitwise operations simply compare with the two possible
type values that we are interested in.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix long_term_keys debugfs output
Johan Hedberg [Fri, 31 Jan 2014 03:39:57 +0000 (19:39 -0800)]
Bluetooth: Fix long_term_keys debugfs output

The code was previously iterating the wrong list (and what's worse
casting entries to a type which they were not) and also missing a proper
line terminator when printing each entry. The code now also prints the
LTK type in hex for easier comparison with the kernel-defined values.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove Simultaneous LE & BR/EDR flags from AD
Johan Hedberg [Thu, 30 Jan 2014 19:16:50 +0000 (11:16 -0800)]
Bluetooth: Remove Simultaneous LE & BR/EDR flags from AD

Starting with the 4.1 Core Specification these flags are no longer used
and should always be cleared. From volume 3, part C, section 13.1.1:

"The 'Simultaneous LE and BR/EDR to Same Device Capable (Controller)'
and â€˜Simultaneous LE and BR/EDR to Same Device Capable (Host)’ bits in
the Flags AD type shall be set to â€˜0’."

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Enable LTK distribution to slave devices
Johan Hedberg [Wed, 29 Jan 2014 21:55:59 +0000 (13:55 -0800)]
Bluetooth: Enable LTK distribution to slave devices

So far we've only been requesting the LTK to be distributed to the
master (initiator) of pairing, which is usually enough since it's the
master that will establish future connections and initiate encryption.
However, in the case that both devices support switching to the opposing
role (which seems to be increasingly common) pairing will have to
performed again since the "new" master will not have all information.

As there is no real harm in it, this patch updates the code to always
try distributing the LTK also to the slave device, thereby enabling role
switches for future connections.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Vinicius Gomes <vcgomes@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Increment management interface revision
Marcel Holtmann [Tue, 28 Jan 2014 23:39:01 +0000 (15:39 -0800)]
Bluetooth: Increment management interface revision

This patch increments the management interface revision due to the
various fixes, improvements and other changes that have been made.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Remove unnecessary check for chan->psm
Johan Hedberg [Tue, 28 Jan 2014 23:28:04 +0000 (15:28 -0800)]
Bluetooth: Remove unnecessary check for chan->psm

Now that ATT sockets have been converted to use the new L2CAP_CHAN_FIXED
type there is no need to have an extra check for chan->psm in the
l2cap_chan_close function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Always use l2cap_chan->psm for returning PSM to user space
Johan Hedberg [Tue, 28 Jan 2014 23:16:51 +0000 (15:16 -0800)]
Bluetooth: Always use l2cap_chan->psm for returning PSM to user space

The l2cap_chan->psm value is always set to a valid value for a
connection oriented channel. The l2cap_chan->sport is used for tracking
local PSM allocations but will not always have a proper value, such as
with connected sockets derived from a listening socket. This patch fixes
the sock_getname callback to always use chan->psm when returning address
information.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Refuse peer RFCOMM address reading when not connected
Johan Hedberg [Tue, 28 Jan 2014 23:16:50 +0000 (15:16 -0800)]
Bluetooth: Refuse peer RFCOMM address reading when not connected

When we're not connected the peer address information is undefined. This
patch fixes the remote address getting to return a proper error in case
the sate is anything else than BT_CONNECTED.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Refuse peer L2CAP address reading when not connected
Johan Hedberg [Tue, 28 Jan 2014 23:16:49 +0000 (15:16 -0800)]
Bluetooth: Refuse peer L2CAP address reading when not connected

When we're not connected the peer address information is undefined. This
patch fixes the remote address getting to return a proper error in case
the state is anything else than BT_CONNECTED.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Free up l2cap_chan->sport when initiating a connection
Johan Hedberg [Tue, 28 Jan 2014 23:16:48 +0000 (15:16 -0800)]
Bluetooth: Free up l2cap_chan->sport when initiating a connection

The sport variable is used to track the allocation of the local PSM
database to ensure no two sockets take the same local PSM. It is
acquired upon bind() but needs to be freed up if the socket ends up
becoming a client one. This patch adds the clearing of the value when
l2cap_chan_connect is called.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix disconnecting L2CAP when a credits overflow occurs
Johan Hedberg [Mon, 27 Jan 2014 23:11:35 +0000 (15:11 -0800)]
Bluetooth: Fix disconnecting L2CAP when a credits overflow occurs

The L2CAP specification requires us to disconnect an L2CAP channel if
the remote side gives us credits beyond 65535. This patch makes sure we
disconnect the channel in such a situation.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix disconnecting L2CAP channel for credits violation
Johan Hedberg [Mon, 27 Jan 2014 23:11:34 +0000 (15:11 -0800)]
Bluetooth: Fix disconnecting L2CAP channel for credits violation

The L2CAP specification requires us to disconnect a channel if the
remote device sends us data when it doesn't have any credits to do so.
This patch makes sure that we send the appropriate L2CAP Disconnect
request in this situation.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix respecting le_default_mps value
Johan Hedberg [Mon, 27 Jan 2014 23:11:33 +0000 (15:11 -0800)]
Bluetooth: Fix respecting le_default_mps value

There's a le_default_mps variable that can be modified through debugfs
but it was never actually used for determining our MPS value. This patch
fixes the MPS initialization to use the variable instead of a fixed
value.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix CID initialization for fixed channels
Johan Hedberg [Sat, 25 Jan 2014 22:10:09 +0000 (17:10 -0500)]
Bluetooth: Fix CID initialization for fixed channels

Fixed channels have the same source and destination CID. Ensure that the
values get properly initialized when receiving incoming connections and
deriving values from the parent socket.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Fix BT_SECURITY socket option for fixed channels (ATT)
Johan Hedberg [Sat, 25 Jan 2014 22:10:07 +0000 (17:10 -0500)]
Bluetooth: Fix BT_SECURITY socket option for fixed channels (ATT)

The BT_SECURITY option should also be allowed for fixed channels, so
punch the appropriate hole for it when checking for the channel type.
The main user of fixed CID user space sockets is right now ATT (which is
broken without this patch).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Switch ATT channels to use L2CAP_CHAN_FIXED
Johan Hedberg [Fri, 24 Jan 2014 08:35:41 +0000 (10:35 +0200)]
Bluetooth: Switch ATT channels to use L2CAP_CHAN_FIXED

ATT channels are not connection oriented so having them use
L2CAP_CHAN_CONN_ORIENTED is quite confusing. Instead, use the new
L2CAP_CHAN_FIXED type and ensure that the MTU and CID values get
properly set.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Rename L2CAP_CHAN_CONN_FIX_A2MP to L2CAP_CHAN_FIXED
Johan Hedberg [Fri, 24 Jan 2014 08:35:40 +0000 (10:35 +0200)]
Bluetooth: Rename L2CAP_CHAN_CONN_FIX_A2MP to L2CAP_CHAN_FIXED

There's no reason why A2MP should need or deserve its on channel type.
Instead we should be able to group all fixed CID users under a single
channel type and reuse as much code as possible for them. Where CID
specific exceptions are needed the chan-scid value can be used.

This patch renames the current A2MP channel type to a generic one and
thereby paves the way to allow converting ATT and SMP (and any future
fixed channel protocols) to use the new channel type.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Remove useless l2cap_seq_list_remove function
Johan Hedberg [Sat, 18 Jan 2014 19:32:59 +0000 (21:32 +0200)]
Bluetooth: Remove useless l2cap_seq_list_remove function

The only user of l2cap_seq_list_remove() was l2cap_seq_list_pop() which
only removes the head, meaning only the "else if (seq_list->head ==
seq)" branch was ever being used. This patch moves the code from this
branch straight into l2cap_seq_list_pop() and removes the (now useless)
l2cap_seq_list_remove().

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Queue incoming ACL data until BT_CONNECTED state is reached
Johan Hedberg [Fri, 17 Jan 2014 18:45:11 +0000 (20:45 +0200)]
Bluetooth: Queue incoming ACL data until BT_CONNECTED state is reached

This patch adds a queue for incoming L2CAP data that's received before
l2cap_connect_cfm is called and processes the data once
l2cap_connect_cfm is called. This way we ensure that we have e.g. all
remote features before processing L2CAP signaling data (which is very
important for making the correct security decisions).

The processing of the pending rx data needs to be done through
queue_work since unlike l2cap_recv_acldata, l2cap_connect_cfm is called
with the hci_dev lock held which could cause potential deadlocks.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Reorder L2CAP functions to avoid forward declarations
Johan Hedberg [Fri, 17 Jan 2014 18:45:10 +0000 (20:45 +0200)]
Bluetooth: Reorder L2CAP functions to avoid forward declarations

This patch moves the l2cap_conn_add, is_valid_psm and l2cap_chan_connect
functions further down in l2cap_core.c. The patch doesn't contain
anything else except the relocation of these functions. By moving the
functions further down the patch enables a subsequent patch that adds a
pending RX queue to be implemented without a forward declaration of a
function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add firmware update for Atheros 0cf3:311f
Oliver Neukum [Thu, 16 Jan 2014 15:02:58 +0000 (16:02 +0100)]
Bluetooth: Add firmware update for Atheros 0cf3:311f

The device is not functional without firmware.

The device without firmware:
T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311f Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

The device with firmware:
T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3007 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Enable Atheros 0cf3:311e for firmware upload
Oliver Neukum [Thu, 16 Jan 2014 14:37:11 +0000 (15:37 +0100)]
Bluetooth: Enable Atheros 0cf3:311e for firmware upload

The device will bind to btusb without firmware, but with the original
buggy firmware device discovery does not work. No devices are detected.

Device descriptor without firmware:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311e Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

with firmware:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311e Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Add debugfs entry to show Secure Connections Only mode
Marcel Holtmann [Thu, 16 Jan 2014 06:37:42 +0000 (22:37 -0800)]
Bluetooth: Add debugfs entry to show Secure Connections Only mode

For debugging purposes of Secure Connection Only support a simple
debugfs entry is used to indicate if this mode is active or not.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Handle security level 4 for RFCOMM connections
Marcel Holtmann [Thu, 16 Jan 2014 06:37:41 +0000 (22:37 -0800)]
Bluetooth: Handle security level 4 for RFCOMM connections

With the introduction of security level 4, the RFCOMM sockets need to
be made aware of this new level. This change ensures that the pairing
requirements are set correctly for these connections.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Handle security level 4 for L2CAP connections
Marcel Holtmann [Thu, 16 Jan 2014 06:37:40 +0000 (22:37 -0800)]
Bluetooth: Handle security level 4 for L2CAP connections

With the introduction of security level 4, the L2CAP sockets need to
be made aware of this new level. This change ensures that the pairing
requirements are set correctly for these connections.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Introduce requirements for security level 4
Marcel Holtmann [Thu, 16 Jan 2014 06:37:39 +0000 (22:37 -0800)]
Bluetooth: Introduce requirements for security level 4

The security level 4 is a new strong security requirement that is based
around 128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms. Which means that E0, SAFER+ and P-192
are not allowed. Only connections created with P-256 resulting from
using Secure Connections support are allowed.

This security level needs to be enforced when Secure Connection Only
mode is enabled for a controller or a service requires FIPS compliant
strong security. Currently it is not possible to enable either of
these two cases. This patch just puts in the foundation for being
able to handle security level 4 in the future.

It should be noted that devices or services with security level 4
requirement can only communicate using Bluetooth 4.1 controllers
with support for Secure Connections. There is no backward compatibilty
if used with older hardware.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Track Secure Connections support of remote devices
Marcel Holtmann [Thu, 16 Jan 2014 06:37:38 +0000 (22:37 -0800)]
Bluetooth: Track Secure Connections support of remote devices

It is important to know if Secure Connections support has been enabled
for a given remote device. The information is provided in the remote
host features page. So track this information and provide a simple
helper function to extract the status.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Fix mgmt error code for negative PIN response
Johan Hedberg [Mon, 13 Jan 2014 15:15:53 +0000 (17:15 +0200)]
Bluetooth: Fix mgmt error code for negative PIN response

The NOT_PAIRED status is only really suitable for operations where being
paired is a pre-requisite. Using it e.g. for the mgmt_pair_device
command seems unintuitive. In the case that either the local or the
remote user responds with a negative PIN Code response the "PIN or Key
Missing" HCI status will be generated. This patch changes the mapping of
this status from the NOT_PAIRED mgmt status to the more intuitive
AUTH_FAILED mgmt status.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10 years agoBluetooth: Convert to use ATTRIBUTE_GROUPS macro
Wei Yongjun [Tue, 7 Jan 2014 14:23:08 +0000 (22:23 +0800)]
Bluetooth: Convert to use ATTRIBUTE_GROUPS macro

Use ATTRIBUTE_GROUPS macro to reduce the number of lines of code.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add support for remote OOB input of P-256 data
Marcel Holtmann [Fri, 10 Jan 2014 10:07:30 +0000 (02:07 -0800)]
Bluetooth: Add support for remote OOB input of P-256 data

The current management interface only allows to provide the remote
OOB input of P-192 data. This extends the command to also accept
P-256 data as well. To make this backwards compatible, the userspace
can decide to only provide P-192 data or the combined P-192 and P-256
data. It is also allowed to leave the P-192 data empty if userspace
only has the remote P-256 data.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add internal function for storing P-192 and P-256 data
Marcel Holtmann [Fri, 10 Jan 2014 10:07:29 +0000 (02:07 -0800)]
Bluetooth: Add internal function for storing P-192 and P-256 data

Add function to allow adding P-192 and P-256 data to the internal
storage. This also fixes a few coding style issues from the previous
helper functions for the out-of-band credentials storage.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Provide remote OOB data for Secure Connections
Marcel Holtmann [Fri, 10 Jan 2014 10:07:28 +0000 (02:07 -0800)]
Bluetooth: Provide remote OOB data for Secure Connections

When Secure Connections has been enabled it is possible to provide P-192
and/or P-256 data during the pairing process. The internal out-of-band
credentials storage has been extended to also hold P-256 data.

Initially the P-256 data will be empty and with Secure Connections enabled
no P-256 data will be provided. This is according to the specification
since it might be possible that the remote side did not provide either
of the out-of-band credentials.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
10 years agoBluetooth: Add debugfs quirk for forcing Secure Connections support
Marcel Holtmann [Fri, 10 Jan 2014 10:07:27 +0000 (02:07 -0800)]
Bluetooth: Add debugfs quirk for forcing Secure Connections support

The Bluetooth 4.1 specification with Secure Connections support has
just been released and controllers with this feature are still in
an early stage.

A handful of controllers have already support for it, but they do
not always identify this feature correctly. This debugfs entry
allows to tell the kernel that the controller can be treated as
it would fully support Secure Connections.

Using debugfs to force Secure Connections support of course does
not make this feature magically appear in all controllers. This
is a debug functionality for early adopters. Once the majority
of controllers matures this quirk will be removed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>