drm/tilcdc: Take crtc modeset lock while updating the crtc clock rate

Take crtc modeset lock while updating the crtc clock rate. To avoid a
race in tilcdc_crtc_update_clk(), we do not want crtc mode to change
while we update crtc clock.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

drm/tilcdc: Choose console BPP that supports RGB

Choose console BPP that supports RGB and remove the old fbdev bpp
selection code. LCDC on AM335x has red and blue wires switched between
24 bit and 16 bit colors. If 24 format is wired for RGB colors, the 16
bit format is wired for BGR. drm_fbdev_cma_init() does not currently
like anything else but RGB formats, so we must choose such bytes per
pixel value that supports RGB.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

drm/tilcdc: Add blue-and-red-crossed devicetree property

Add "blue-and-red-wiring"-device tree property and update devicetree
binding document.

The red and blue components are reversed between 24 and 16 bit modes
on am335x LCDC output pins. To get 24 RGB format the red and blue
wires has to be crossed and this in turn causes 16 colors output to be
in BGR format. With straight wiring the 16 color is RGB and 24 bit is
BGR.

The new property describes whether the red and blue wires are crossed
or not. If the property is not present or its value is not recognized
the legacy mode is assumed. The legacy configuration supports RGB565,
RGB888 and XRGB8888 formats. However, depending on wiring, the red and
blue colors are swapped in either 16 or 24-bit color modes.

For more details see section 3.1.1 in AM335x Silicon Errata:
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

drm/tilcdc: Write DMA base and ceiling address with single instruction

Write DMA base and ceiling address with a single instruction, if
available. This should make it more unlikely that LCDC would fetch the
DMA addresses in the middle of an update. Having bad combination of
addresses in dma base and ceiling (e.g base > ceiling) can cause
unpredictaple behavior in LCDC.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

drm/tilcdc: Remove drm_helper_disable_unused_functions() call

drm_helper_disable_unused_functions() should not be called by atomic
drivers.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

drm/tilcdc: Enable EOF interrupts for v1 LCDC

This got accidentally dropped in the fixed commit and is required for
the driver to properly work on the rev1 IP, such as found on the LCDK.

Fixes: 2b2080d7e9ae ("drm/tilcdc: Get rid of complex ping-pong mechanism")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

drm/tilcdc: Adjust the FB_CEILING address

The LCDC seems to expect its framebuffer ceiling address pointer to be
an inclusive bound.  The IP rev2 seems to cope with that but rev1 (as
found on the LCDK) don't.
Also note that this is what the framebuffer code does in da8xx-fb.c.

Since, as the TRM puts it, "The 2 LSBs are hardwired to 00b", the
dma_addr_t can be decremented without cast.
I tested it with a v2 (AM335x, rev  0x4F201000) and an LCDK (v1).

Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

drm/tilcdc: Fix check for remote port parent

In function tilcdc_get_external_components the check for
the remote port parent is not correct. We need a '||' instead of
an '&&'.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

Revert "drm: make DRI1 drivers depend on BROKEN"

This reverts commit d10571fc4fba7d57fb8157f0be61dcbe4a7965ca.

This isn't how we get to do this unfortunately.

Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge tag 'topic/drm-misc-2016-08-31' of git://anongit.freedesktop.org/drm-intel into drm-next

More -misc stuff
- moar drm_crtc.c split up&documentation
- some fixes for the simple kms helpers (Andrea)
- I included all the dri1 patches from David - we're not removing any code
  or drivers, and it seems to have worked as a wake-up call to motivate a
  few more people to upstream kms conversions for these. Feel free to
  revert if you disagree strongly.
- a few other single patches

* tag 'topic/drm-misc-2016-08-31' of git://anongit.freedesktop.org/drm-intel: (24 commits)
  drm: drm_probe_helper: Fix output_poll_work scheduling
  drm: bridge/dw-hdmi: Fix colorspace and scan information registers values
  drm/doc: Polish docs for drm_property&drm_property_blob
  drm: Unify handling of blob and object properties
  drm: Extract drm_property.[hc]
  drm: move drm_mode_legacy_fb_format to drm_fourcc.c
  drm/doc: Polish docs for drm_mode_object
  drm: Remove drm_mode_object->atomic_count
  drm: Extract drm_mode_object.[hc]
  drm/doc: Polish kerneldoc for encoders
  drm: Extract drm_encoder.[hc]
  drm/fb-helper: don't call remove_conflicting_framebuffers for FB=m && DRM=y
  drm/atomic-helper: Add NO_DISABLE_AFTER_MODESET flag support for plane commit
  drm/atomic-helper: Disable appropriate planes in disable_planes_on_crtc()
  drm/atomic-helper: Add atomic_disable CRTC helper callback
  drm: simple_kms_helper: add support for bridges
  drm: simple_kms_helper: make connector optional at init time
  drm/bridge: introduce bridge detaching mechanism
  drm/simple-helpers: Always add planes to the state update
  drm: reduce GETCLIENT to a minimum
  ...

drm: drm_probe_helper: Fix output_poll_work scheduling

drm_kms_helper_poll_enable_locked() should check if we have delayed event
pending and if we have, schedule the work to run without delay.

Currently the output_poll_work is only scheduled if any of the connectors
have DRM_CONNECTOR_POLL_CONNECT or DRM_CONNECTOR_POLL_DISCONNECT with
DRM_OUTPUT_POLL_PERIOD delay. It does not matter if we have delayed event
already registered to be handled. The detection will be delayd by
DRM_OUTPUT_POLL_PERIOD in any case.
Furthermore if none of the connectors are marked as POLL_CONNECT or
POLL_DISCONNECT because all connectors are either POLL_HPD or they are
always connected: the output_poll_work will not run at all even if we
have delayed event marked.

When none of the connectors require polling, their initial status change
from unknown to connected/disconnected is not going to be handled until
the first kms application starts or if we have fb console enabled.

Note that in general the output poll work should be enabled already
when this happens, but at driver load usually the first probe happens
before the output polling is enabled. This patch fixes this case.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[danvet: Note when exactly this is an issue, since the probe code
schedules the poll work itself already.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160831110905.31289-1-peter.ujfalusi@ti.com

drm: bridge/dw-hdmi: Fix colorspace and scan information registers values

Colorspace and scan information values were being written in wrong
offsets. This patch corrects this and writes the values at the
offsets specified in the databook.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/96fd0f06b7ebc2ee5cb8239a99648f3107e24497.1471530573.git.joabreu@synopsys.com

drm/doc: Polish docs for drm_property&drm_property_blob

- remove kerneldoc for drm-internal functions
- drm_property_replace_global_blob isn't actually atomic, and doesn't
  need to be. Update docs&comments to match
- document all the types and try to link things a bit better
- nits all over

v2: Appease checkpatch in the moved code (Archit)

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-9-daniel.vetter@ffwll.ch

drm: Unify handling of blob and object properties

They work exactly the same now, after the refcounting unification a bit
ago. The only reason they're distinct is backwards compat with existing
userspace.

Cc: Daniel Stone <daniels@collabora.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-8-daniel.vetter@ffwll.ch

drm: Extract drm_property.[hc]

This just contains the base property classes and all the code to
handle blobs. I think for any kind of standardized/shared properties
it's better to have separate files - this is fairly big already as-is.

v2: resurrect misplaced hunk (Daniel Stone)

Cc: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-7-daniel.vetter@ffwll.ch

drm: move drm_mode_legacy_fb_format to drm_fourcc.c

It's part of the drm fourcc handling code, mapping the old depth/bpp
values to new fourcc codes.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-6-daniel.vetter@ffwll.ch

drm/doc: Polish docs for drm_mode_object

I figured an overview section here is overkill, and better
to just document the 2 structures themselves well enough.

v2: Review from Archit:
- Appease checkpatch in moved code.
- Spelling fixes in the kerneldoc.

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-5-daniel.vetter@ffwll.ch

drm: Remove drm_mode_object->atomic_count

It's only used in drm_mode_object_get_properties, and we can compute
it there directly with a bit of code shuffling.

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-4-daniel.vetter@ffwll.ch

drm: Extract drm_mode_object.[hc]

Just for the struct drm_mode_object base class. The header file was
already partially extracted to help untangle the include loops.

v2:
- Also move the generic get/set property ioctls. At first this seemed
  like a bad idea since it requires making drm_mode_crtc_set_obj_prop
  non-static. But eventually that will get split away too (like
  the connector version already is) for both crtc and planes. Hence I
  reconsidered.

- drm_mode_object.[hc] instead of drm_modeset.[hc], which requires
  renaming the drm_modeset.h header I already started building up.
  This is more consistent (matches the name of the main structure),
  and I want to be able to use drm_modeset.[hc] for the basic modeset
  init/cleanup functionality like drm_mode_config_init.

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-3-daniel.vetter@ffwll.ch

drm/doc: Polish kerneldoc for encoders

- Move missing bits into struct drm_encoder docs.
- Explain that encoders are 95% internal and only 5% uapi, and that in
  general the uapi part is broken.
- Remove verbose comments for functions not exposed to drivers.

v2: Review from Archit:
- Appease checkpatch in the moved code.
- Make it clearer that bridges are not exposed to userspace.

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-2-daniel.vetter@ffwll.ch

drm: Extract drm_encoder.[hc]

Same treatment as before. Only hiccup is drm_crtc_mask, which
unfortunately can't be resolved until drm_crtc.h is less of a monster.
Untangle the header loop with a forward declaration for that static
inline.

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829082757.17913-1-daniel.vetter@ffwll.ch

drm/fb-helper: don't call remove_conflicting_framebuffers for FB=m && DRM=y

When CONFIG_DRM_KMS_FB_HELPER is disabled, we can have a configuration
in which some DRM drivers are built-in, but the framebuffer core is a
loadable module. This results in a link error, such as:

drivers/gpu/drm/radeon/radeon.o: In function `radeon_pci_probe':
radeon_kfd.c:(.text.radeon_pci_probe+0xbc): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/amd/amdgpu/amdgpu.o: In function `amdgpu_pci_probe':
amdgpu_mn.c:(.text.amdgpu_pci_probe+0xa8): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/mgag200/mgag200.o: In function `mga_vram_init':
mgag200_ttm.c:(.text.mga_vram_init+0xa8): undefined reference to `remove_conflicting_framebuffers'
drivers/gpu/drm/mgag200/mgag200.o: In function `mga_pci_probe':
mgag200_ttm.c:(.text.mga_pci_probe+0x88): undefined reference to `remove_conflicting_framebuffers'
Makefile:969: recipe for target 'vmlinux' failed

This changes the compile-time check to IS_REACHABLE, which means we end up
not calling remove_conflicting_framebuffers() in the configuration, which
seems good enough, as we know that no framebuffer driver is loaded by the
time that the built-in DRM driver calls remove_conflicting_framebuffers.

We could alternatively avoid the link error by forcing CONFIG_FB to not
be a module in this case, but that wouldn't change anything at runtime,
and just make the already convoluted set of dependencies worse here.

I could not find out what happens if the fbdev driver gets loaded as
a module after the DRM driver is already initialized, but that is a case
that can happen with or without this patch.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0a3bfe29f816 ("drm/fb-helper: Fix the dummy remove_conflicting_framebuffers")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829123428.3260105-1-arnd@arndb.de
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com

drm/atomic-helper: Add NO_DISABLE_AFTER_MODESET flag support for plane commit

Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com

drm/atomic-helper: Disable appropriate planes in disable_planes_on_crtc()

Currently, the helper drm_atomic_helper_disable_planes_on_crtc() calls
->atomic_disable for all planes _to be_ enabled on a particular CRTC.
This is obviously wrong for those planes which are not scanning out frames
when the helper is called.  Instead, it's sane to disable active planes
of old_crtc_state in the helper.

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472196644-30563-3-git-send-email-gnuiyl@gmail.com

drm/atomic-helper: Add atomic_disable CRTC helper callback

Some display controllers need plane(s) to be disabled together with
the relevant CRTC, e.g., the IPUv3 display controller for imx-drm.
This patch adds atomic_disable CRTC helper callback so that
old_crtc_state(as a parameter of the callback) could be used
to get the active plane(s) of the old CRTC state for disable operation.

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472196644-30563-2-git-send-email-gnuiyl@gmail.com

drm: simple_kms_helper: add support for bridges

Introduce drm_simple_display_pipe_attach_bridge() and
drm_simple_display_pipe_detach_bridge() in order to make it possible to use
drm encoders with the simple display pipes managed by simple_kms_helpers

Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-3-git-send-email-andrea.merello@gmail.com

drm: simple_kms_helper: make connector optional at init time

drm_simple_display_pipe_init() pretends to attach a connector
to the display pipe.

In case a drm bridge has to be used, then it's the bridge that
takes care of connectors.

This patch makes the connector parameter optional for
drm_simple_display_pipe_init(), so that a drm bridge could
handle connector by itself later.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-2-git-send-email-andrea.merello@gmail.com

drm/bridge: introduce bridge detaching mechanism

Up to now, once a bridge has been attached to a DRM device, it cannot
be undone.

In particular you couldn't rmmod/insmod a DRM driver that uses a bridge,
because the bridge would remain bound to the first (dead) driver instance.

This patch fixes this by introducing drm_encoder_detach() and a ->detach
callback in drm_bridge_funcs for the bridge to be notified about detaches.

It's DRM/KMS driver responsibility to call drm_encoder_detach().

While adding the bridge detach callback, with its kerneldoc, I also added
kerneldoc for attach callback.

Few other kerneldocs fixes around there are included.

Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1472115874-6219-1-git-send-email-andrea.merello@gmail.com

drm/simple-helpers: Always add planes to the state update

Our update function is hooked to the single plane, which might not get
called for crtc-only updates. Which is surprising, so fix this by
always adding the plane.

While at it document how&when the event should be sent out better in
the kerneldoc.

Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: andrea.merello@gmail.com
Tested-and-Reported-by: andrea.merello@gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471933540-31131-1-git-send-email-daniel.vetter@ffwll.ch

drm: reduce GETCLIENT to a minimum

The *only* known user of GETCLIENT is libva, which uses it to check
whether its own context is authenticated. It used to iterate all clients,
look for one that matches its own pid and then check its state.

The entire purpose for us to still have a GETCLIENT implementation is to
serve libva. So lets not pretend we do anything else: Make this function
return information on the caller's context only, fake the PID to the
caller's pid so they always match, and just fill in the "authenticated"
bit, nothing else.

This patch reduces the complexity of GETCLIENT to a bare minimum, avoids
any dependency on priv->uid or priv->pid (allows us to get rid of them),
and makes libva happy by always *exactly* returning the information it
wants.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160825143505.7447-1-dh.herrmann@gmail.com

drm: make DRI1 drivers depend on BROKEN

The legacy DRI1 drivers expose highly broken interfaces to user-space. No
modern system should enable them, or you will effectively allow user-space
to circumvent most of your kernel security measures. The DRI1 kernel APIs
are simply broken.

User-space can always use vesafb/efifb/simplefb and friends to get working
graphics.

Lets hide the old drivers behind CONFIG_BROKEN. In case they turn out to
be still used (really?), we can easily revert this and figure out a way to
move them out of sight (e.g., moving all DRI1 drivers to
drivers/gpu/dri1/).

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160804080657.9664-2-dh.herrmann@gmail.com

drm: hide legacy drivers with CONFIG_DRM_LEGACY

Lets move forward and hide the remaining DRI1 drivers behind a config
option, so we have a central place to disable them all. Furthermore, we
can provide a clear warning to anyone enabling them.

Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160804080657.9664-1-dh.herrmann@gmail.com

Merge branch 'drm-next-4.9' of git://people.freedesktop.org/~agd5f/linux into drm-next

First drm-next pull for radeon and amdgpu for 4.9.  Highlights:
- powerplay support for iceland asics
- improved GPU reset (both full asic and per block)
- UVD and VCE powergating for CZ and ST
- VCE clockgating for CZ and ST
- Support for pre-initialized (e.g., zeroed) vram buffers
- ttm cleanups
- virtual display support
- core and radeon/amdgpu support for page_flip_target
- lots of bug fixes and clean ups

* 'drm-next-4.9' of git://people.freedesktop.org/~agd5f/linux: (171 commits)
  drm/amdgpu: use memcpy_toio for VCE firmware upload
  drm/amdgpu: use memcpy_to/fromio for UVD fw upload
  drm/amd/powerplay: delete useless code in iceland_hwmgr.c.
  drm/radeon: switch UVD code to use UVD_NO_OP for padding
  drm/amdgpu: switch UVD code to use UVD_NO_OP for padding
  drm/radeon: add support for UVD_NO_OP register
  drm/amdgpu: add support for UVD_NO_OP register
  drm/amdgpu: fix VCE ib alignment value
  drm/amdgpu: fix IB alignment for UVD
  drm/amd/amdgpu: Print ring name in amdgpu_ib_schedule()
  drm/radeon: remove dead code, si_mc_load_microcode (v2)
  drm/radeon/cik: remove dead code (v2)
  drm/amd/powerplay: avoid NULL dereference, cz_hwmgr.c
  drm/amd/powerplay: avoid NULL pointer dereference
  drm/amdgpu/gmc8: remove dead code (v2)
  drm/amdgpu/gmc7: remove dead code (v2)
  drm/amdgpu: Fix indentation in dce_v8_0_audio_write_sad_regs()
  drm/amdgpu: Use correct mask in dce_v8_0_afmt_setmode() and fix comment typos.
  drm/amdgpu: cleanup amdgpu_vm_bo_update params
  drm/amdgpu: stop adding dummy entry in amdgpu_ttm_placement_init
  ...

Merge branch 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel into drm-next

drm-intel-next-2016-08-22:
- bugfixes and cleanups for rcu-protected requests (Chris)
- atomic modeset fixes for gpu reset on pre-g4x (Maarten&Ville)
- guc submission improvements (Dave Gordon)
- panel power sequence cleanup (Imre)
- better use of stolen and unmappable ggtt (Chris), plus prep work to make that
  happen
- rework of framebuffer offsets, prep for multi-plane framebuffers (Ville)
- fully partial ggtt vmaps, including fenced ones (Chris)
- move lots more of the gem tracking from the object to the vma (Chris)
- tune the command parser (Chris)
- allow fbc without fences on recent platforms (Chris)
- fbc frontbuffer tracking fixes (Chris)
- fast prefaulting using io-mappping.h pgprot caching (Chris)

* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (141 commits)
  io-mapping: Fixup for different names of writecombine
  io-mapping.h: s/PAGE_KERNEL_IO/PAGE_KERNEL/
  drm/i915: Update DRIVER_DATE to 20160822
  drm/i915: Use remap_io_mapping() to prefault all PTE in a single pass
  drm/i915: Embed the io-mapping struct inside drm_i915_private
  io-mapping: Always create a struct to hold metadata about the io-mapping
  drm/i915/fbc: Allow on unfenced surfaces, for recent gen
  drm/i915/fbc: Don't set an illegal fence if unfenced
  drm/i915: Flush delayed fence releases after reset
  drm/i915: Reattach comment, complete type specification
  drm/i915/cmdparser: Accelerate copies from WC memory
  drm/i915/cmdparser: Use binary search for faster register lookup
  drm/i915/cmdparser: Check for SKIP descriptors first
  drm/i915/cmdparser: Compare against the previous command descriptor
  drm/i915/cmdparser: Improve hash function
  drm/i915/cmdparser: Only cache the dst vmap
  drm/i915/cmdparser: Use cached vmappings
  drm/i915/cmdparser: Add the TIMESTAMP register for the other engines
  drm/i915/cmdparser: Make initialisation failure non-fatal
  drm/i915: Stop discarding GTT cache-domain on unbind vma
  ...

Merge branch 'for-next' of git://people.freedesktop.org/~seanpaul/dogwood into drm-next

This pull request contains the following rockchip drm changes:

  - Introduce support for rk3399 vop/crtc
  - Add PSR framework to the rockchip driver
  - Implement PSR in the rockchip analogix edp driver
  - Fix panel on/off in analogix to avoid damaging panels
  - Some miscellaneous fixes to clean up logs and code readability

* 'for-next' of git://people.freedesktop.org/~seanpaul/dogwood:
  drm/rockchip: analogix_dp: drop unnecessary probe deferral "error" print
  drm/rockchip: Enable vblank without event
  drm/rockchip: Improve analogix-dp psr handling
  drm/rockchip: A couple small fixes to psr
  drm/rockchip: Use a spinlock to protect psr state
  drm/rockchip: Don't use a delayed worker for psr state changes
  drm/rockchip: Convert psr_list_mutex to spinlock and use it
  drm/rockchip: analogix_dp: implement PSR function
  drm/bridge: analogix_dp: add the PSR function support
  drm/rockchip: add an common abstracted PSR driver
  drm/rockchip: vop: export line flag function
  drm/bridge: analogix_dp: Ensure the panel is properly prepared/unprepared
  dt-bindings: add compatible strings for big/little rockchip vops
  dt-bindings: sort Rockchip vop compatible by chip's number
  drm/rockchip: vop: add rk3399 vop support
  drm/rockchip: vop: introduce VOP_REG_MASK
  drm/rockchip: sort registers define by chip's number

drm/amdgpu: use memcpy_toio for VCE firmware upload

Try to be clean here, even when it's a noop on x86.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use memcpy_to/fromio for UVD fw upload

Also use the firmware size from the header instead of calculating it.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: delete useless code in iceland_hwmgr.c.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: switch UVD code to use UVD_NO_OP for padding

Replace packet2's with packet0 writes to UVD_NO_OP.  The
value written to UVD_NO_OP does not matter.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: switch UVD code to use UVD_NO_OP for padding

Replace packet2's with packet0 writes to UVD_NO_OP.  The
value written to UVD_NO_OP does not matter.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: add support for UVD_NO_OP register

Writes to this register are the preferred way to do NOPs.

Bump the driver version as well.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add support for UVD_NO_OP register

Writes to this register are the preferred way to do NOPs.

Bump the driver version as well.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix VCE ib alignment value

The VCE rings only require single dword alignment.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix IB alignment for UVD

According to the hw team, it should be 16, not 8.

Cc: Peter Fang <peter.fang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/doc: Fix vga_switcheroo xref

Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: b754b35b089d ("vgaarbiter: rst-ifiy and polish kerneldoc")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160824101916.30125-1-daniel.vetter@ffwll.ch

io-mapping: Fixup for different names of writecombine

Somehow architectures can't agree on this. And for good measure make
sure we have a fallback which should work everywhere (fingers
crossed).

v2: Make it compile properly, needs a defined() for the #elif.

Fixes: ac96b5566926 ("io-mapping.h: s/PAGE_KERNEL_IO/PAGE_KERNEL/")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: linux-mm@kvack.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160823202233.4681-1-daniel.vetter@ffwll.ch
(cherry picked from commit 80c33624e4723c4e22d9917cd676067ebf652dc2)

io-mapping.h: s/PAGE_KERNEL_IO/PAGE_KERNEL/

PAGE_KERNEL_IO is an x86-ism. Though it is used to define the pgprot_t
used for the iomapped region, it itself is just PAGE_KERNEL. On all
other arches, PAGE_KERNEL_IO is undefined so in a general header we must
refrain from using it.

v2: include pgtable for pgprot_combine()

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: cafaf14a5d8f ("io-mapping: Always create a struct to hold metadata about the io-mapping")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: linux-mm@kvack.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160823155024.22379-1-chris@chris-wilson.co.uk
(cherry picked from commit ac96b5566926af83463ddcf4655856033c092f26)

drm/gma500: remove unnecessary config_enabled() guard

Commit d112a8163f83 ("gma500/cdv: Add eDP support") replaced the
code inside this if-conditional with gma_backlight_set(), which
becomes a nop stub if CONFIG_BACKLIGHT_CLASS_DEVICE is disabled.
So, there is no need to guard the caller with config_enabled().

Note:
This is one of remaining TODOs to deprecate config_enabled() macro.
Refer to commit 97f2645f358b ("tree-wide: replace config_enabled()
with IS_ENABLED()").

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471970574-23906-1-git-send-email-yamada.masahiro@socionext.com

drm/doc: Document uapi requirements in DRM

Everyone knows them, except all the new folks joining from the ARM
side haven't lived through all the pain of the past years and are
entirely surprised when I raise this. Definitely time to document
this.

Last time this was a big discussion was about 6 years ago, when qcom
tried to land a kernel driver without userspace. Dave Airlie made the
rules really clear:

http://airlied.livejournal.com/73115.html

This write-up here is essentially what I've put into a presentation a
while ago, which was also reviewed by Dave:

http://blog.ffwll.ch/2015/05/gfx-kernel-upstreaming-requirements.html

v2: Fix typos Eric&Rob spotted.

v3: Nitpick from Jani.

Cc: Dave Airlie <airlied@gmail.com>
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge tag 'topic/drm-misc-2016-08-23' of git://anongit.freedesktop.org/drm-intel into drm-next

A few bigger things:
- start of splitting drm_crtc.c into more manageable and better documneted
  chunks
- DRM_DEV_* logging (Sean)

* tag 'topic/drm-misc-2016-08-23' of git://anongit.freedesktop.org/drm-intel: (46 commits)
  drm/fb-helper: Make docs for fb_set_suspend wrappers consistent
  drm/rockchip: Delete unnecessary assignment for the field "owner"
  drm/bridge: dw-hdmi: Delete unnecessary assignment for the field "owner"
  drm/rockchip: Don't continue trying to enable crtc on failure
  drm/fb-helper: Add drm_fb_helper_set_suspend_unlocked()
  drm/fb-helper: Fix the dummy remove_conflicting_framebuffers
  drm/udl: Ensure channel is selected before using the device.
  drm: Avoid calling dev_printk(.dev = NULL)
  drm: avoid exposing kernel stack in compat_drm_getstats
  reservation: fix small comment typo
  drm: Don't implement empty prepare_fb()/cleanup_fb()
  virtio-gpu: Use memdup_user() rather than duplicating its implementation
  GPU-DRM-Savage: Use memdup_user() rather than duplicating
  drm: Allow drivers to modify plane_state in prepare_fb/cleanup_fb
  drm/rockchip: Use DRM_DEV_ERROR in vop
  drm: Introduce DRM_DEV_* log messages
  drm/edid: CEA mode 64 1080p100 vsync pulse width incorrect
  Revert "drm/hisilicon: Don't set drm_device->platformdev"
  dma-buf: fix kernel-doc warning and typos
  drm: Fix kerneldoc in drm_plane_helper.c
  ...

drm/fb-helper: Make docs for fb_set_suspend wrappers consistent

I figured I might as well go ocd and make them booleans and rename the
locked version too.

v2: Review from Noralf.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Fixes: cfe63423d9be ("drm/fb-helper: Add drm_fb_helper_set_suspend_unlocked()")
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160823152727.31788-1-daniel.vetter@ffwll.ch

drm/amd/amdgpu: Print ring name in amdgpu_ib_schedule()

If the ring isn't ready lets print out which ring name
to help debugging.

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: remove dead code, si_mc_load_microcode (v2)

In an if block for (running == 0) running cannot be non-zero.

v2: agd: remove unused variable

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/cik: remove dead code (v2)

In an if block for (running == 0) running cannot be non-zero.

v2: agd: remove unused variable

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: avoid NULL dereference, cz_hwmgr.c

if (a == NULL || a->b == NULL)
leads to a NULL pointer dereference if a == NULL.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: avoid NULL pointer dereference

if (a == NULL || a->b == NULL)
leads to a NULL pointer dereference if a == NULL.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gmc8: remove dead code (v2)

In an if block for (running == 0) running cannot be non-zero.

v2: agd: remove unused variable

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gmc7: remove dead code (v2)

In an if block for (running == 0) running cannot be non-zero.

v2: agd: remove unused variable

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix indentation in dce_v8_0_audio_write_sad_regs()

Fixed indentation for readability.

Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/rockchip: analogix_dp: drop unnecessary probe deferral "error" print

This driver is the only user of of_drm_find_panel() which prints an
error before doing probe deferral, yielding messages like this on boot,
before eventually succeeding:

[    2.234271] [drm:rockchip_dp_probe] *ERROR* failed to find panel
...
[    4.797539] [drm:rockchip_dp_probe] *ERROR* failed to find panel
...

Let's just drop the message.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: Enable vblank without event

vblank should be enabled regardless of whether an event
is expected back. This is especially important for a cursor
plane.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chip.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: Improve analogix-dp psr handling

Remove the delayed worker, opting instead for the non-delayed
variety. Also introduce a lock to ensure we don't have races
with the worker and psr_state. Finally, cancel and wait for
the worker to finish when disabling the bridge.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: A couple small fixes to psr

A few things that need tidying up, no functional changes.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: Use a spinlock to protect psr state

The handling of psr state is racey, shore that up with
a per-psr driver lock.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: Don't use a delayed worker for psr state changes

The delayed worker isn't needed and is racey. Remove it and do
the state change in line.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: Convert psr_list_mutex to spinlock and use it

This patch converts the psr_list_mutex to a spinlock and locks
all access to psr_list to avoid races (however unlikely they
were).

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: analogix_dp: implement PSR function

Alway enable the PSR function for Rockchip analogix_dp driver. If panel
don't support PSR, then the core analogix_dp would ignore this setting.

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/bridge: analogix_dp: add the PSR function support

The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.

This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: add an common abstracted PSR driver

The PSR driver have exported four symbols for specific device driver, and
it's safe to call them in interrupt context:
- rockchip_drm_psr_register()
- rockchip_drm_psr_unregister()
- rockchip_drm_psr_enable()
- rockchip_drm_psr_disable()
- rockchip_drm_psr_flush()

Encoder driver should call the register/unregister interfaces to hook
itself into common PSR driver, encoder have implement the 'psr_set'
callback which use the set PSR state in hardware side.

Crtc driver would call the enable/disable interfaces when vblank is
enable/disable, after that the common PSR driver would call the encoder
registered callback to set the PSR state.

Fb driver would call the flush interface in 'fb->dirty' callback, this
helper function would force all PSR enabled encoders to exit from PSR
for 3 seconds.

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul removed leftover psr_enabled/psr_work kruft from drm_vop.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: vop: export line flag function

VOP have integrated a hardware counter which indicate the exact display
line that vop is scanning. And if we're interested in a specific line,
we can set the line number to vop line_flag register, and then vop would
generate a line_flag interrupt for it.

For example eDP PSR function is interested in the vertical blanking
period, then driver could set the line number to zero.

This patch have exported a symbol that allow other driver to listen the
line flag event with given timeout limit:
-  rockchip_drm_wait_line_flag()

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/bridge: analogix_dp: Ensure the panel is properly prepared/unprepared

Instead of just preparing the panel on bind, actually prepare/unprepare
during modeset/disable. The panel must be prepared in order to read hpd
status and edid, so we need to keep state around the prepares in order
to ensure we don't accidentally turn the panel off at the wrong time.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

dt-bindings: add compatible strings for big/little rockchip vops

This patch documents the compatible strings for the big and little vop
in rockchip's drm driver.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul removed superfluous description per tfiga's review]
Signed-off-by: Sean Paul <seanpaul@chromium.org>

dt-bindings: sort Rockchip vop compatible by chip's number

Reorder the compatible vop devices to be sorted by chip number
in ascending order.

Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul added commit description per tfiga's review]
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: vop: add rk3399 vop support

There are two VOP in rk3399 chip, respectively VOP_BIG and VOP_LIT.
most registers layout of this two vop is same, their framework are both
VOP_FULL, the Major differences of this two is that:

VOP_BIG max output resolution is 4096x2160.
VOP_LIT max output resolution is 2560x1600

VOP_BIG support four windows.
VOP_LIT only support two windows.

RK3399 vop register layout is similar with rk3288, so some feature
can reuse with rk3288.

Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: vop: introduce VOP_REG_MASK

Some new vop register support mask, bit[16-31] is mask,
bit[0-15] is value, the mask is correspond to the value.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul masked 'v' per tfiga's review comments]
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: sort registers define by chip's number

No functional changes, sort the vop registers to make
code more readable.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul resolved conflict with name change from _3066 to _3036]
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: Delete unnecessary assignment for the field "owner"

The field "owner" is set by the core.
Thus delete an unneeded initialisation.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/41e48fd3-f713-7225-1df2-3b1f4758f949@users.sourceforge.net

drm/bridge: dw-hdmi: Delete unnecessary assignment for the field "owner"

The field "owner" is set by the core.
Thus delete an unneeded initialisation.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/7c97565d-eee3-45e9-b494-9e802977502c@users.sourceforge.net

drm/rockchip: Don't continue trying to enable crtc on failure

If vop_enable fails, don't continue on, it causes system hangs.

Reviewed-by: Yakir Yank <ykk@rock-chips.com>
Tested-by: Yakir Yank <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1471302749-2811-1-git-send-email-seanpaul@chromium.org

drm/fb-helper: Add drm_fb_helper_set_suspend_unlocked()

This adds a function that also takes the console lock before calling
fb_set_suspend() in contrast to drm_fb_helper_set_suspend() which is
a plain wrapper around fb_set_suspend().
Resume is run asynchronously using a worker if the console lock is
already taken. This is modelled after the i915 driver.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471953246-29602-1-git-send-email-noralf@tronnes.org

drm/fb-helper: Fix the dummy remove_conflicting_framebuffers

We always need to remove conflicting framebuffers if any other fb driver
is enabled, and not just if we are setting up an fbdev ourselves.

Unfortunately remove_conflicting_framebuffers() was incorrectly stubbed
out if !fbdev rather than !fb leading to major memory corruption (and
corrupt filesystems) upon boot.

Fixes: 44adece57e26 ("drm/fb-helper: Add a dummy remove_conflicting_framebuffers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: tomi.valkeinen@ti.com
Cc: dh.herrmann@gmail.com
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160822204452.2509-1-chris@chris-wilson.co.uk

drm/udl: Ensure channel is selected before using the device.

Lift configuration command from udlfb. This appears to be essential for
at least a Rextron VCUD-60, without which no URB communication occurs.

Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471904254-26545-1-git-send-email-jm@lentin.co.uk

drm/amdgpu: Use correct mask in dce_v8_0_afmt_setmode() and fix comment typos.

We were using the same mask twice. Looking at radeon, it seems
we should be using HDMI_AVI_INFO_CONT instead as the second mask.

Being there, fix typos in comments and improved readability.

I haven't looked at other DCEs, the mask may also be wrong for them.

Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup amdgpu_vm_bo_update params

Make it more obvious what we are doing here.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: stop adding dummy entry in amdgpu_ttm_placement_init

AMDGPU_GEM_CREATE_NO_CPU_ACCESS and AMDGPU_GEM_CREATE_CPU_ACCESS_REQUIRED are
obviously mutual exclusive. So stop adding a dummy entry without effect when
both are specified.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup amdgpu_ttm_placement_init

Make it more clear what this function does. No intendet functional change.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix lru size grouping v2

Adding a BO can make it the insertion point for larger sizes as well.

v2: add a comment about the guard structure.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay:  Tidy up cz_hwmgr.c

Clean up whitespace and formatting.

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add AMDGPU_INFO_NUM_EVICTIONS

For profiling.

v2: really bump the minor version

Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: recover vram bo from shadow after gpu reset V2

V2:
1. don't directly submit to many jobs at the same time.
2. delete unrelated printk.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: link all shadow bo V2

V2:
1. use mutex instead of spinlock for shadow list, since its process could
sleep.
2. move list_del to bo destroy phase.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: update pt shadow while updating pt V2

V2:
move shadow parameter to amdgpu_pte_update_params.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: minutemaidpark@hotmail.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: update pd shadow while updating pd V2

V2:
Checking if shadow is valid.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: sync bo and shadow V3

Use shadow flag to judge which direction to sync.
V2:
Don't need bo pin, so remove it.

V3:
1. Split to two functions, one is backup_to_shadow, another is
restore_from_shadow.
2. Clean up previous shadow direction difinitions.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add direct submision option for copy_buffer

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm: Avoid calling dev_printk(.dev = NULL)

Since dev_printk likes to print "(NULL device *):" when passed in a NULL
pointer, we have to manually call printk() ourselves.

Fixes: c4e68a583202 ("drm: Introduce DRM_DEV_* log messages")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Engestrom <eric.engestrom@imgtec.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160819073750.16610-1-chris@chris-wilson.co.uk

drm: avoid exposing kernel stack in compat_drm_getstats

The C standard does not specify the size of the integer used
to store an enum. Hence in structure drm_stats32_t alignment
bytes may exist.

To avoid exposing bytes from the kernel stack it is
necessary to initialize variable s32 completely.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471802179-2886-1-git-send-email-xypron.glpk@gmx.de

reservation: fix small comment typo

Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet: Mark up as function for proper cross-linking.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1471640134-30888-1-git-send-email-robdclark@gmail.com

drm/i915: Update DRIVER_DATE to 20160822

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/amdgpu: add need backup function V2

V2:
add checking if need backup in amdgpu_bo_create.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>