[PATCH] sched: tweak affine wakeups

Do less affine wakeups.  We're trying to reduce dbt2-pgsql idle time
regressions here...  make sure we don't don't move tasks the wrong way in an
imbalance condition.  Also, remove the cache coldness requirement from the
calculation - this seems to induce sharp cutoff points where behaviour will
suddenly change on some workloads if the load creeps slightly over or under
some point.  It is good for periodic balancing because in that case have
otherwise have no other context to determine what task to move.

But also make a minor tweak to "wake balancing" - the imbalance tolerance is
now set at half the domain's imbalance, so we get the opportunity to do wake
balancing before the more random periodic rebalancing gets preformed.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sched: balance timers

Do CPU load averaging over a number of different intervals.  Allow each
interval to be chosen by sending a parameter to source_load and target_load.
0 is instantaneous, idx > 0 returns a decaying average with the most recent
sample weighted at 2^(idx-1).  To a maximum of 3 (could be easily increased).

So generally a higher number will result in more conservative balancing.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sched: less aggressive idle balancing

Remove the special casing for idle CPU balancing.  Things like this are
hurting for example on SMT, where are single sibling being idle doesn't really
warrant a really aggressive pull over the NUMA domain, for example.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sched: add debugging

These conditions should now be impossible, and we need to fix them if they
happen.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sched: fix SMT scheduling problems

SMT balancing has a couple of problems.  Firstly, active_load_balance is too
complex - basically it should be a dumb helper for when the periodic balancer
has determined there is an imbalance, but gets stuck because the task is
running.

So rip out all its "smarts", and just make it move one task to the target CPU.

Second, the busy CPU's sched-domain tree was being used for active balancing.
This means that it may not see that nr_balance_failed has reached a critical
level.  So use the target CPU's sched-domain tree for this.  We can do this
because we hold its runqueue lock.

Lastly, reset nr_balance_failed to a point where we allow cache hot migration.
This will help ensure active load balancing is successful.

Thanks to Suresh Siddha for pointing out these issues.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sched: reduce active load balancing

Fix up active load balancing a bit so it doesn't get called when it shouldn't.
Reset the nr_balance_failed counter at more points where we have found
conditions to be balanced.  This reduces too aggressive active balancing seen
on some workloads.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sched: improve load balancing pinned tasks

John Hawkes explained the problem best:

A large number of processes that are pinned to a single CPU results
in every other CPU's load_balance() seeing this overloaded CPU as
"busiest", yet move_tasks() never finds a task to pull-migrate.  This
condition occurs during module unload, but can also occur as a
denial-of-service using sys_sched_setaffinity().  Several hundred
CPUs performing this fruitless load_balance() will livelock on the
busiest CPU's runqueue lock.  A smaller number of CPUs will livelock
if the pinned task count gets high.

Expanding slightly on John's patch, this one attempts to work out whether the
balancing failure has been due to too many tasks pinned on the runqueue.  This
allows it to be basically invisible to the regular blancing paths (ie.  when
there are no pinned tasks).  We can use this extra knowledge to shut down the
balancing faster, and ensure the migration threads don't start running which
is another problem observed in the wild.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sched: cleanup wake_idle

New sched-domains code means we don't get spans with offline CPUs in
them.

Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] hpet: do_div fix

We don't need to use do_div() on a 32-bit quantity.

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] reiserfs: do not ignore i/io error on readpage

Reiserfs's readpage does not notice i/o errors.  This patch makes
reiserfs_readpage to return -EIO when i/o error appears.

This patch makes reiserfs to not ignore I/O error on readpage.

Signed-off-by: Qu Fuping <fs@ercist.iscas.ac.cn>
Signed-off-by: Vladimir V. Saveliev <vs@namesys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] mconf.c needs locale.h

This is failing on my cross-compilation environment (From a solaris system)
using gcc-3.4.1 (as the compiler can't find a prototype for the setlocale()
function).

Signed-off-by: Jean-Christophe Dubois <jdubois@mc.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] fix for generic_file_write iov problem

Here is the fix for the problem described in

http://bugzilla.kernel.org/show_bug.cgi?id=4721

Basically, problem is generic_file_buffered_write() is accessing beyond end
of the iov[] vector after handling the last vector.  If we happen to cross
page boundary, we get a fault.

I think this simple patch is good enough.  If we really don't want to
depend on the "count", then we need pass nr_segs to
filemap_set_next_iovec() and decrement it and check it.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] fix fsync(dir) return value for ram-based filesystems

Any filesystem which is using simple_dir_operations will retunr -EINVAL for
fsync() on a directory.  Make it return zero instead.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] tpm: fix misc name memory problem

I was using invalid memory for the miscdevice.name.  This patch fixes the
problem which was manifested by an ugly entry in /proc/misc.

Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] tpm: Fix pubek parsing

Fix parsing of the PUBEK for display which was leading to showing the wrong
modulus length and modulus.

Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] tpm: Support new National TPMs

This patch is work to support new National TPMs that problems were reported
with on Thinkpad T43 and Thinkcentre S51.  Thanks to Jens and Gang for
their debugging work on these issues.

Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] RCU: clean up a few remaining synchronize_kernel() calls

2.6.12-rc6-mm1 has a few remaining synchronize_kernel()s, some (but not
all) in comments.  This patch changes these synchronize_kernel() calls (and
comments) to synchronize_rcu() or synchronize_sched() as follows:

- arch/x86_64/kernel/mce.c mce_read(): change to synchronize_sched() to
  handle races with machine-check exceptions (synchronize_rcu() would not cut
  it given RCU implementations intended for hardcore realtime use.

- drivers/input/serio/i8042.c i8042_stop(): change to synchronize_sched() to
  handle races with i8042_interrupt() interrupt handler.  Again,
  synchronize_rcu() would not cut it given RCU implementations intended for
  hardcore realtime use.

- include/*/kdebug.h comments: change to synchronize_sched() to handle races
  with NMIs.  As before, synchronize_rcu() would not cut it...

- include/linux/list.h comment: change to synchronize_rcu(), since this
  comment is for list_del_rcu().

- security/keys/key.c unregister_key_type(): change to synchronize_rcu(),
  since this is interacting with RCU read side.

- security/keys/process_keys.c install_session_keyring(): change to
  synchronize_rcu(), since this is interacting with RCU read side.

Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Makefile: s/gcc-option/cc-option/

Fixes http://bugme.osdl.org/show_bug.cgi?id=4726

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] compilation errors in drivers/serial/mpsc.c

The following patch fix gcc 4 compilation errors in drivers/serial/mpsc.c

Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s390: debug feature changes

This patch changes the memory allocation method for the s390 debug feature.
Trace buffers had been allocated using the get_free_pages() function before.
Therefore it was not possible to get big memory areas in a running system due
to memory fragmentation.  Now the trace buffers are subdivided into several
subbuffers with pagesize.  Therefore it is now possible to allocate more
memory for the trace buffers and more trace records can be written.

In addition to that, dynamic specification of the size of the trace buffers is
implemented.  It is now possible to change the size of a trace buffer using a
new debugfs file instance.  When writing a number into this file, the trace
buffer size is changed to 'number * pagesize'.

In the past all the traces could be obtained from userspace by accessing files
in the "proc" filesystem.  Now with debugfs we have a new filesystem which
should be used for debugging purposes.  This patch moves the debug feature
from procfs to debugfs.

Since the interface of debug_register() changed, all device drivers, which use
the debug feature had to be adjusted.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s390: add vmcp interface

Add interface to issue VM control program commands.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s390: improved machine check handling

Improved machine check handling.  Kernel is now able to receive machine checks
while in kernel mode (system call, interrupt and program check handling).
Also register validation is now performed.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s/390: compile fix for dcssblk

Fix compile breakage in the dcss block driver introduced by the attribute
changes.

Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s/390: use klist in dasd driver

Convert the dasd driver to use the new klist interface.

Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s/390: Use klist in cio

Convert the common I/O layer to use the klist interfaces.

This patch has been adapted from the previous version to the changed interface
semantics.  Also, gcc 4.0 compile warnings have been removed.

Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: add profile_pc for i386

Cope with a conditional i386 definition, which is wrong for UML.  Before we
just used that one, but it wasn't defined for CONFIG_SMP, so in that case
we got link errors.

Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: hot-unplug code cleanup

Clean up the hot-unplugging code.  There is now an id procedure which is
called to figure out what device we're talking to.  The error messages from
that are now done from mconsole_remove instead of the driver.  remove is now
called with the device number, after it has been checked, so doesn't need to
do sanity checking on it.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: time initialization tidying

user_time_init_skas and user_time_init_tt were essentially the same.  So, this
merges them, deleting the mode-specific functions and declarations.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: always disable kmalloc during shutdown

kmalloc wasn't being disabled during panic.  This patch ensures that, no
matter how UML is exiting, it is disabled.  This matters because part of the
cleanup is to remove the umid file, which involves readdir, which calls
malloc.  This must map to libc malloc, rather than kmalloc or vmalloc.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: fix timer initialization

In skas mode, the call to uml_idle_timer permanently shut off the virtual
timer, resulting in no timer ticks to anything but the idle thread.  This is
likely the cause of the soft lockups that are seen sporadically in recent
UMLs.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: fork cleanup

Fix the do_fork calling convention: normal arch pass the regs and the new sp
value to do_fork instead of NULL.

Currently the arch-independent code ignores these values, while the UML code
(actually it's copy_thread) gets the right values by itself.

With this patch, things are fixed up.

Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: kfree cleanup

Here's a small patch to remove a few unnessesary NULL pointer checks before
kfree() in arch/um/drivers/daemon_user.c

Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: fix sizeof usage

Size of pointer doesn't seem right, but maybe my solution isn't either
(sig_size maybe?).

Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Update video-after-suspend documentation

Update video-after-suspend documentation; few more machines are added.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] swsusp: only allow it when it makes sense

Show swsuspend only on .config where it can compile.  I got this on PPC32 &&
SMP:

kernel/power/smp.c:24: error: storage size of `ctxt' isn't known

Also mark swsusp as no longer experimental.

Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] suspend: PCI power managment reference implementation

Added reference implementation of suspend and resume routines.

From: Shaohua Li <shaohua.li@intel.com>

  build fix

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] CPU hotplug printk fix

In the cpu hotplug case, per-cpu data possibly isn't initialized even the
system state is 'running'.  As the comments say in the original code, some
console drivers assume per-cpu resources have been allocated.  radeon fb is
one such driver, which uses kmalloc.  After a CPU is down, the per-cpu data
of slab is freed, so the system crashed when printing some info.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] swsusp: clean assembly parts

This patch fixes register saving so that each register is only saved once,
and adds missing saving of %cr8 on x86-64.  Some reordering so that
save/restore is more logical/safer (segment registers should be restored
after gdt).

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] swsusp: fix nr_copy_pages

The following patch moves the recalculation of nr_copy_pages so that the right
number is used in the calculation of the size of memory and swap needed.

It prevents swsusp from attempting to suspend if there is not enough memory
and/or swap (which is unlikely anyway).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] swsusp: cleanup whitespace

The following patch cleans up whitespace in swsusp.c (a bit):

- removes any trailing whitespace

- adds spaces after if, for, for_each_pbe, for_each_zone etc., wherever
  necessary.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] swsusp: kill unneccessary does_collide_order

The following patch removes the unnecessary function does_collide_order().

This function is no longer necessary, as currently there are only 0-order
allocations in swsusp, and the use of it is confusing.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] properly stop devices before poweroff

Without this patch, Linux provokes emergency disk shutdowns and
similar nastiness. It was in SuSE kernels for some time, IIRC.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] acpi: fix video docs

This fixes typos/formatting in video_extension.txt.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s-t-RAM: load gdt the right way

Sleep code uses wrong version of lgdt, that does the wrong thing when
gdt is beyond 16MB or so.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] swsusp: kill config_pm_disk

CONFIG_PM_DISK is long gone, but it still managed to survived at few
places.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] swsusp: documentation updates

This updates documentation and fixes pointers in MAINTAINERS file.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] suspend/resume SMP support

Using CPU hotplug to support suspend/resume SMP.  Both S3 and S4 use
disable/enable_nonboot_cpus API.  The S4 part is based on Pavel's original S4
SMP patch.

Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] generate hotplug events for cpu online

We already do kobject_hotplug for cpu offline; this adds a kobject_hotplug
call for the online case.  This is being requested by developers of an
application which wants to be notified about both kinds of events.

Signed-off-by: Nathan Lynch <ntl@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] set cpu_state for CPU hotplug (ia64)

Dead CPU notifies online CPU that it's dead using cpu_state variable.
After switching to physical cpu hotplug, we forgot setting the variable.
This patch fixes it.  Currently only __cpu_die uses it.  We changed other
locations for consistency in case others use it.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] x86_64: Provide ability to choose using shortcuts for IPI in flat mode.

This patch provides an option to switch broadcast or use mask version for
sending IPI's.  If CONFIG_HOTPLUG_CPU is defined, we choose not to use
broadcast shortcuts by default, otherwise we choose broadcast mode as default.

both cases, one can change this via startup cmd line option, to choose
no-broadcast mode.

no_ipi_broadcast=1

This is provided on request from Andi Kleen, since he doesnt agree with
replacing IPI shortcuts as a solution for CPU hotplug.  Without removing
broadcast IPI's, it would mean lots of new code for __cpu_up() path, which
would acheive the same results.

Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] x86_64: Dont use broadcast shortcut to make it cpu hotplug safe.

Broadcast IPI's provide un-expected behaviour for cpu hotplug.  CPU's in
offline state also end up receiving the IPI.  Once the cpus become online they
receive these stale IPI's which are bad and introduce unexpected behaviour.

This is easily avoided by not sending a broadcast and addressing just the
CPU's in online map.  Doing prelim cycle counts it appears there is no big
overhead and numbers seem around 0x3000-0x3900 on an average on x86 and x86_64
systems with CPUS running 3G, both for broadcast and mask version of the
API's.

The shortcuts are useful only for flat mode (where the perf shows no
degradation), and in cluster mode, its unicast anyway.  Its simpler to just
not use broadcast anymore.

Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] x86_64: CPU hotplug sibling map cleanup

This patch is a minor cleanup to the cpu sibling/core map.  It is required
that this setup happens on a per-cpu bringup time.

Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] x86_64: CPU hotplug support

  Experimental CPU hotplug patch for x86_64
  -----------------------------------------
This supports logical CPU online and offline.
- Test with maxcpus=1, and then kick other cpu's off to test if init code
  is all cleaned up. CONFIG_SCHED_SMT works as well.
- idle threads are forked on demand from keventd threads for clean startup

TBD:
1. Not tested on a real NUMA machine (tested with numa=fake=2)
2. Handle ACPI pieces for physical hotplug support.

Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Shaohua.li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] x86_64: Change init sections for CPU hotplug support

This patch adds __cpuinit and __cpuinitdata sections that need to exist past
boot to support cpu hotplug.

Caveat: This is done *only* for EM64T CPU Hotplug support, on request from
Andi Kleen.  Much of the generic hotplug code in kernel, and none of the other
archs that support CPU hotplug today, i386, ia64, ppc64, s390 and parisc dont
mark sections with __cpuinit, but only mark them as __devinit, and
__devinitdata.

If someone is motivated to change generic code, we need to make sure all
existing hotplug code does not break, on other arch's that dont use __cpuinit,
and __cpudevinit.

Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] make smp_prepare_cpu to a weak function

I really wish smp_prepare_cpu() would disappear eventually.  In the interim
this is ideally a weak function, so we dont end up changing several places
to define this dummy in headers.

Today since the dummy declaration is done only in drivers/base/cpu.c but
the function is called in kernel/power/smp.c i get undefined reference in
my cpu hotplug code for x86_64 under development.

Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] cpu state clean after hot remove

Clean CPU states in order to reuse smp boot code for CPU hotplug.

Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] init call cleanup

Trival patch for CPU hotplug.  In CPU identify part, only did cleaup for intel
CPUs.  Need do for other CPUs if they support S3 SMP.

Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sibling map initializing rework

Make sibling map init per-cpu.  Hotplug CPU may change the map at runtime.

Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sep initializing rework

Make SEP init per-cpu, so it is hotplug safe.

Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] i386: Dont use IPI broadcast when using cpu hotplug.

This patch introduces a startup parameter no_broadcast.  When we enable
CONFIG_HOTPLUG_CPU, we dont want to use broadcast shortcut as it has ill
effects on a offline cpu.  If we issue broadcast, the IPI is also delivered
to offline cpus, or partially up cpu causing stale IPI's to be handled,
which is a problem and can cause undesirable effects.

Introduces a new startup cmdline option no_ipi_broadcast, that can be
switched at cmdline if necessary.

Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] i386 CPU hotplug

(The i386 CPU hotplug patch provides infrastructure for some work which Pavel
is doing as well as for ACPI S3 (suspend-to-RAM) work which Li Shaohua
<shaohua.li@intel.com> is doing)

The following provides i386 architecture support for safely unregistering and
registering processors during runtime, updated for the current -mm tree.  In
order to avoid dumping cpu hotplug code into kernel/irq/* i dropped the
cpu_online check in do_IRQ() by modifying fixup_irqs().  The difference being
that on cpu offline, fixup_irqs() is called before we clear the cpu from
cpu_online_map and a long delay in order to ensure that we never have any
queued external interrupts on the APICs.  There are additional changes to s390
and ppc64 to account for this change.

1) Add CONFIG_HOTPLUG_CPU
2) disable local APIC timer on dead cpus.
3) Disable preempt around irq balancing to prevent CPUs going down.
4) Print irq stats for all possible cpus.
5) Debugging check for interrupts on offline cpus.
6) Hacky fixup_irqs() to redirect irqs when cpus go off/online.
7) play_dead() for offline cpus to spin inside.
8) Handle offline cpus set in flush_tlb_others().
9) Grab lock earlier in smp_call_function() to prevent CPUs going down.
10) Implement __cpu_disable() and __cpu_die().
11) Enable local interrupts in cpu_enable() after fixup_irqs()
12) Don't fiddle with NMI on dead cpu, but leave intact on other cpus.
13) Program IRQ affinity whilst cpu is still in cpu_online_map on offline.

Signed-off-by: Zwane Mwaikambo <zwane@linuxpower.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] variable overflow after hundreds round of hotplug CPU

I'm doing the cpu hotplug stress test and found a variable ('ready') is
overflow after several hundreds rounds of cpu hotplug.  Here is a fix.

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] CPU hotplug: fix hpet sectioning

With hpet enabled, cpu hotplug uses some routines marked with __init.

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dmi: spring cleanup

Whitespace and CodingStyle cleanup. No functionality changes.

Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dmi: remove central blacklist

Since last dmi quirk looks useless (it just prints 404 compliant url) we can
finally remove central dmi blacklist.

Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dmi: move ACPI sleep quirk

This patch moves ACPI sleep quirk out of dmi_scan.c

Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dmi: move ACPI boot quirk

This patch moves ACPI boot quirks out of dmi_scan.c

Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc64: Fix compile warnings in arch/ppc64/kernel/lparcfg.c

Stephen's patch to remove LparData.h missed an include in lparcfg.c This
fixes a few compile warnings.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc32: remove some unnecessary includes of bootmem.h

Continue the Good Fight:  Limit bootmem.h include creep.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] I2C-MPC: Remove OCP device model support

All consumers of the driver MPC10x, MPC52xx, MPC824x, MPC83xx, and MPC85xx are
all using platform devices.  We can get ride of the dead code to support using
this driver with the old OCP based model

Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc32: Remove FSL OCP support

Support for the OCP device model on Freescale (FSL) PPC's is no longer used.
All FSL PPC's that were using OCP have be converted to using the platform
device model.

Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc32: Add support for Freescale e200 (Book-E) core

The e200 core is a Book-E core (similar to e500) that has a unified L1 cache
and is not cache coherent on the bus.  The e200 core also adds a separate
exception level for debug exceptions.  Part of this patch helps to cleanup a
few cases that are true for all Freescale Book-E parts, not just e500.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ppc32: Check return of ppc_sys_get_pdata before accessing pointer

Ensure that the returned pointer from ppc_sys_get_pdata is not NULL before we
start using it.  This handles any cases where we have variants of processors
on the same board with different functionality.

Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] selinux: add executable heap check

This patch,based on sample code by Roland McGrath, adds an execheap
permission check that controls the ability to make the heap executable so
that this can be prevented in almost all cases (the X server is presently
an exception, but this will hopefully be resolved in the future) so that
even programs with execmem permission will need to have the anonymous
memory mapped in order to make it executable.

The only reason that we use a permission check for such restriction (vs.
making it unconditional) is that the X module loader presently needs it; it
could possibly be made unconditional in the future when X is changed.

The policy patch for the execheap permission is available at:
http://pearls.tuxedo-es.org/patches/selinux/policy-execheap.patch

Signed-off-by: Lorenzo Hernandez Garcia-Hierro <lorenzo@gnu.org>
Acked-by: James Morris <jmorris@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] selinux: add executable stack check

This patch adds an execstack permission check that controls the ability to
make the main process stack executable so that attempts to make the stack
executable can still be prevented even if the process is allowed the
existing execmem permission in order to e.g.  perform runtime code
generation.  Note that this does not yet address thread stacks.  Note also
that unlike the execmem check, the execstack check is only applied on
mprotect calls, not mmap calls, as the current security_file_mmap hook is
not passed the necessary information presently.

The original author of the code that makes the distinction of the stack
region, is Ingo Molnar, who wrote it within his patch for
/proc/<pid>/maps markers.
(http://marc.theaimsgroup.com/?l=linux-kernel&m=110719881508591&w=2)

The patches also can be found at:
http://pearls.tuxedo-es.org/patches/selinux/policy-execstack.patch
http://pearls.tuxedo-es.org/patches/selinux/kernel-execstack.patch

policy-execstack.patch is the patch that needs to be applied to the policy in
order to support the execstack permission and exclude it
from general_domain_access within macros/core_macros.te.

kernel-execstack.patch adds such permission to the SELinux code within
the kernel and adds the proper permission check to the selinux_file_mprotect() hook.

Signed-off-by: Lorenzo Hernandez Garcia-Hierro <lorenzo@gnu.org>
Acked-by: James Morris <jmorris@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] mm: fix remap_pte_range BUG

Out-of-tree user of remap_pfn_range hit kernel BUG at mm/memory.c:1112!  It
passes an unrounded size to remap_pfn_range, which was okay before 2.6.12,
but misses remap_pte_range's new end condition.  An audit of all the other
ptwalks confirms that this is the only one so exposed.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Fix the error handling in direct I/O

Fix a bug on error handling in the direct I/O function.

Currently, if a file is opened with the O_DIRECT|O_SYNC flag, the write()
syscall cannot receive the EIO error after an I/O error (SCSI cable is
disconnected etc.).

Return values of other points that call generic_osync_inode() are treated
appropriately.

Signed-off-by: Hisashi Hifumi <hifumi.hisashi@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] mips: add MIPS-specific support for flatmem/discontigmem

2.6.12-git6 doesn't boot on some MIPS machines.  They need the support of flat
memory and discontig memory.

Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Serial: remove unnecessary register_serial/unregister_serial

A couple of drivers declare register_serial/unregister_serial prototypes
but don't use them.  FRV contains a commented out call to register_serial.
Since these are deprecated, remove these unnecessary references.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] gcc4 compile fix for recent ia64 xpc changes

Gcc4 doesn't like volatile casts as lvalues.  Make the structure members
volatile instead.

Signed-off-by: Dave Jones <davej@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] I8K: add new BIOS signatures

I8K: add BIOS signatures of a newer Dell laptops, also there can be
     more than one temperature sensor reported by BIOS. Lifted from
     driver 1.25 on Massimo Dal Zotto's site.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] I8K: initialization code cleanup; formatting

I8K: use module_{init|exit} instead of old style #ifdef MODULE
     code, some formatting changes.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] I8K: convert to seqfile

I8K: Change proc code to use seq_file.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] I8K: use standard DMI interface

I8K: Change to use stock dmi infrastructure instead of homegrown
     parsing code. The driver now requires box's DMI data to match
     list of supported models so driver can be safely compiled-in
     by default without fear of it poking into random SMM BIOS
     code. DMI checks can be ignored with i8k.ignore_dmi option.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] I8K: pass through lindent

I8K: pass through Lindent to change 4 spaces identation to TABs

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Toshiba driver cleanup

Toshiba legacy driver cleanup:
 - use module_init/module_exit for initialization instead of using
   #ifdef MODULE and calling tosh_init manually from drivers/char/misc.c
 - do not explicitly initialize static variables
 - some whitespace and formatting cleanups

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] cx88 build fix

static declaration of cx88_pci_irqs follows non-static.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dvb-bt8xx.txt fixes

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Merge master.kernel.org:/home/rmk/linux-2.6-arm

[PATCH] ARM: Generic Dynamic Tick Timer support for ARM, take 4

This patch adds support for Dynamic Tick Timer for ARM. Dynamic Tick is
also known as VST (Variable Scheduling Timeouts).

Dynamic Tick has been in use in the OMAP tree since last October.  The
patch is not intrusive, and does not do anything unless CONFIG_NO_IDLE_HZ
is defined.  This patch has the following fixed based on comments from
RMK:
- Time is updated before calling interrupt handlers.
- Added new interrupt flag SA_TIMER to avoid duplicate timer interrupts
- Moved struct dyn_tick_timer to time.h until we at some point probably
  have an arch independent dyn-tick.h
- Cleaned up testing for DYN_TICK_ENABLED in irq.c

 I've cleaned up this patch to fix some remaining issues:
 - Call the timer tick handler with irqs disabled, as it would be from
   a normal interrupt
 - if we have a dyn_tick, we better implement all methods.
 - generic timer_dyn_reprogram() call, to be called before sleeping
 - added command line option - "dyntick=" to allow boot-time control
   of this feature
    -- rmk

Signed-off-by: Tony Lindgren
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2752/1: disable ixp2000 PCI I/O software workaround on chips that don't need it

Patch from Lennert Buytenhek

The later ixp2000 models don't need the PCI I/O workaround that we
currently perform.  Add a config option to disable the workaround,
and panic on boot if a kernel without the workaround is booted on a
buggy chip.  As only pre-production ixp2000s need the workaround,
the default is for it not to be configured in.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: Fix discontigmem

The merge of sparsemem broke ARM discontigmem.  Fix it.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge /pub/scm/linux/kernel/git/davem/sparc-2.6

ACPI: Make sure we call acpi_register_gsi() even for default PCI interrupt assignment

That's the part that keeps track of the ELCR register, and we want to
make sure that the PCI interrupts are properly marked level/low.

[PATCH] ARM: 2751/1: ixp2000 gpio cleanup broke ixdp2800 build

Patch from Lennert Buytenhek

The ixp2000 gpio cleanup broke the ixdp2800 build as it moved some
gpio-related functions from arch/platform.h to arch/gpio.h and the
ixdp2x00 support code used those functions but didn't include the
latter header file.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2750/1: add i2c platform device for enp2611 on-board i2c bus

Patch from Lennert Buytenhek

On the enp2611, GPIO 7 and 6 are connected to an on-board i2c bus that
attaches to the SODIMM module slot (for SPD) and an LM84 temperature
sensor.  Add a platform device for this i2c bus.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2749/1: update ixp2000 defconfigs to 2.6.12-git6

Patch from Lennert Buytenhek

Update the defconfigs for the ixp2000 platforms to 2.6.12-git6.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[TG3]: Update driver version and reldate.

Signed-off-by: David S. Miller <davem@davemloft.net>

[TG3]: Refinements to new locking strategy.

1. Move tp->irq_sync = 0 to before the interrupt mailbox IO in
   tg3_enable_ints() so that the interrupt handler will always see
   irq_sync == 0 when interrupts are enabled.

2. Remove the tg3_enable_ints() call in tg3_reset_hw(). Interrupts are
   always enabled explicitly or through tg3_netif_start(). This is to
   prevent interrupts being enabled while poll is disabled.

3. Update trans_start with jiffies in tg3_netif_stop() to prevent false
   NETDEV WATCHDOG.

4. Pass in the proper irq_sync parameter to tg3_full_lock() depending on
   netif_running() in some of the ethtool set calls.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TG3]: Eliminate all hw IRQ handler spinlocks.

Move all driver spinlocks to be taken at sw IRQ
context only.

This fixes the skb_copy() we were doing with hw
IRQs disabled (which is illegal and triggers a
BUG() with HIGHMEM enabled).  It also simplifies
the locking all over the driver tremendously.

We accomplish this feat by creating a special
sequence to synchronize with the hw IRQ handler
using a binary state and synchronize_irq().
This idea is from Herbert Xu.

Thanks to Michael Chan for helping to track down
all of the race conditions in initial versions
of this code.

Signed-off-by: David S. Miller <davem@davemloft.net>