iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode

commit 8bef455c8b1694547ee59e8b1939205ed9d901a6 upstream.

The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.

The meaning of the sequencing register for the aux channels changes
depending on the mode.

In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.

In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.

Currently the driver does not have the special handling required for
simultaneous mode. Add it.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: xilinx-xadc: Fix clearing interrupt when enabling trigger

commit f954b098fbac4d183219ce5b42d76d6df2aed50a upstream.

When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.

The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: xilinx-xadc: Fix ADC-B powerdown

commit e44ec7794d88f918805d700240211a9ec05ed89d upstream.

The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: stm32-adc: fix sleep in atomic context

commit e2042d2936dfc84e9c600fe9b9d0039ca0e54b7d upstream.

This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"

In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.

Fixes: 2763ea0585c9 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Remove ASUS ROG Zenith from the blacklist

[ Upstream commit a8cf44f085ac12c0b5b8750ebb3b436c7f455419 ]

The commit 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist") added a
new blacklist for the devices that are known to have empty codecs, and
one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f).
However, it turned out that the very same PCI SSID is used for the
previous model that does have the valid HD-audio codecs and the change
broke the sound on it.

This patch reverts the corresponding entry as a temporary solution.
Although Zenith II and co will see get the empty HD-audio bus again,
it'd be merely resource wastes and won't affect the functionality,
so it's no end of the world.  We'll need to address this later,
e.g. by either switching to DMI string matching or using PCI ID &
SSID pairs.

Fixes: 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200419071926.22683-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KEYS: Avoid false positive ENOMEM error on key read

[ Upstream commit 4f0882491a148059a52480e753b7f07fc550e188 ]

By allocating a kernel buffer with a user-supplied buffer length, it
is possible that a false positive ENOMEM error may be returned because
the user-supplied length is just too large even if the system do have
enough memory to hold the actual key data.

Moreover, if the buffer length is larger than the maximum amount of
memory that can be returned by kmalloc() (2^(MAX_ORDER-1) number of
pages), a warning message will also be printed.

To reduce this possibility, we set a threshold (PAGE_SIZE) over which we
do check the actual key length first before allocating a buffer of the
right size to hold it. The threshold is arbitrary, it is just used to
trigger a buffer length check. It does not limit the actual key length
as long as there is enough memory to satisfy the memory request.

To further avoid large buffer allocation failure due to page
fragmentation, kvmalloc() is used to allocate the buffer so that vmapped
pages can be used when there is not a large enough contiguous set of
pages available for allocation.

In the extremely unlikely scenario that the key keeps on being changed
and made longer (still <= buflen) in between 2 __keyctl_read_key()
calls, the __keyctl_read_key() calling loop in keyctl_read_key() may
have to be iterated a large number of times, but definitely not infinite.

Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vrf: Check skb for XFRM_TRANSFORMED flag

[ Upstream commit 16b9db1ce34ff00d6c18e82825125cfef0cdfb13 ]

To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.

Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: Always set XFRM_TRANSFORMED in xfrm{4,6}_output_finish

[ Upstream commit 0c922a4850eba2e668f73a3f1153196e09abb251 ]

IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.

Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: b53: Fix ARL register definitions

[ Upstream commit c2e77a18a7ed65eb48f6e389b6a59a0fd753646a ]

The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.

Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

team: fix hang in team_mode_get()

[ Upstream commit 1c30fbc76b8f0c07c92a8ca4cd7c456612e17eb5 ]

When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
    genl_lock(); by genl_rcv_msc()
        rtnl_lock(); by team_nl_cmd_options_set()
            mutex_lock(&team->lock); by team_nl_team_get()

Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
    genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.

The problem secenario.
CPU0                                     CPU1
team_mode_get
    request_module()
                                         modprobe -r team_mode_roundrobin
                                                     team <--(B)
        modprobe team <--(A)
            team_mode_roundrobin

By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.

By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.

Test commands:
    while :
    do
        teamd -d &
killall teamd &
modprobe -rv team_mode_roundrobin &
    done

The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.

Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: cache line align MAX_TCP_HEADER

[ Upstream commit 9bacd256f1354883d3c1402655153367982bba49 ]

TCP stack is dumb in how it cooks its output packets.

Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.

If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/x25: Fix x25_neigh refcnt leak when receiving frame

[ Upstream commit f35d12971b4d814cdb2f659d76b42f0c545270b6 ]

x25_lapb_receive_frame() invokes x25_get_neigh(), which returns a
reference of the specified x25_neigh object to "nb" with increased
refcnt.

When x25_lapb_receive_frame() returns, local variable "nb" becomes
invalid, so the refcount should be decreased to keep refcount balanced.

The reference counting issue happens in one path of
x25_lapb_receive_frame(). When pskb_may_pull() returns false, the
function forgets to decrease the refcnt increased by x25_get_neigh(),
causing a refcnt leak.

Fix this issue by calling x25_neigh_put() when pskb_may_pull() returns
false.

Fixes: cb101ed2c3c7 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: netrom: Fix potential nr_neigh refcnt leak in nr_add_node

[ Upstream commit d03f228470a8c0a22b774d1f8d47071e0de4f6dd ]

nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.

When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.

The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.

Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.

Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bcmgenet: correct per TX/RX ring statistics

[ Upstream commit a6d0b83f25073bdf08b8547aeff961a62c6ab229 ]

The change to track net_device_stats per ring to better support SMP
missed updating the rx_dropped member.

The ndo_get_stats method is also needed to combine the results for
ethtool statistics (-S) before filling in the ethtool structure.

Fixes: 37a30b435b92 ("net: bcmgenet: Track per TX/RX rings statistics")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

macvlan: fix null dereference in macvlan_device_event()

[ Upstream commit 4dee15b4fd0d61ec6bbd179238191e959d34cf7a ]

In the macvlan_device_event(), the list_first_entry_or_null() is used.
This function could return null pointer if there is no node.
But, the macvlan module doesn't check the null pointer.
So, null-ptr-deref would occur.

      bond0
        |
   +----+-----+
   |          |
macvlan0   macvlan1
   |          |
 dummy0     dummy1

The problem scenario.
If dummy1 is removed,
1. ->dellink() of dummy1 is called.
2. NETDEV_UNREGISTER of dummy1 notification is sent to macvlan module.
3. ->dellink() of macvlan1 is called.
4. NETDEV_UNREGISTER of macvlan1 notification is sent to bond module.
5. __bond_release_one() is called and it internally calls
   dev_set_mac_address().
6. dev_set_mac_address() calls the ->ndo_set_mac_address() of macvlan1,
   which is macvlan_set_mac_address().
7. macvlan_set_mac_address() calls the dev_set_mac_address() with dummy1.
8. NETDEV_CHANGEADDR of dummy1 is sent to macvlan module.
9. In the macvlan_device_event(), it calls list_first_entry_or_null().
At this point, dummy1 and macvlan1 were removed.
So, list_first_entry_or_null() will return NULL.

Test commands:
    ip netns add nst
    ip netns exec nst ip link add bond0 type bond
    for i in {0..10}
    do
        ip netns exec nst ip link add dummy$i type dummy
ip netns exec nst ip link add macvlan$i link dummy$i \
type macvlan mode passthru
ip netns exec nst ip link set macvlan$i master bond0
    done
    ip netns del nst

Splat looks like:
[   40.585687][  T146] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP DEI
[   40.587249][  T146] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[   40.588342][  T146] CPU: 1 PID: 146 Comm: kworker/u8:2 Not tainted 5.7.0-rc1+ #532
[   40.589299][  T146] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   40.590469][  T146] Workqueue: netns cleanup_net
[   40.591045][  T146] RIP: 0010:macvlan_device_event+0x4e2/0x900 [macvlan]
[   40.591905][  T146] Code: 00 00 00 00 00 fc ff df 80 3c 06 00 0f 85 45 02 00 00 48 89 da 48 b8 00 00 00 00 00 fc ff d2
[   40.594126][  T146] RSP: 0018:ffff88806116f4a0 EFLAGS: 00010246
[   40.594783][  T146] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[   40.595653][  T146] RDX: 0000000000000000 RSI: ffff88806547ddd8 RDI: ffff8880540f1360
[   40.596495][  T146] RBP: ffff88804011a808 R08: fffffbfff4fb8421 R09: fffffbfff4fb8421
[   40.597377][  T146] R10: ffffffffa7dc2107 R11: 0000000000000000 R12: 0000000000000008
[   40.598186][  T146] R13: ffff88804011a000 R14: ffff8880540f1000 R15: 1ffff1100c22de9a
[   40.599012][  T146] FS:  0000000000000000(0000) GS:ffff888067800000(0000) knlGS:0000000000000000
[   40.600004][  T146] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   40.600665][  T146] CR2: 00005572d3a807b8 CR3: 000000005fcf4003 CR4: 00000000000606e0
[   40.601485][  T146] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   40.602461][  T146] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   40.603443][  T146] Call Trace:
[   40.603871][  T146]  ? nf_tables_dump_setelem+0xa0/0xa0 [nf_tables]
[   40.604587][  T146]  ? macvlan_uninit+0x100/0x100 [macvlan]
[   40.605212][  T146]  ? __module_text_address+0x13/0x140
[   40.605842][  T146]  notifier_call_chain+0x90/0x160
[   40.606477][  T146]  dev_set_mac_address+0x28e/0x3f0
[   40.607117][  T146]  ? netdev_notify_peers+0xc0/0xc0
[   40.607762][  T146]  ? __module_text_address+0x13/0x140
[   40.608440][  T146]  ? notifier_call_chain+0x90/0x160
[   40.609097][  T146]  ? dev_set_mac_address+0x1f0/0x3f0
[   40.609758][  T146]  dev_set_mac_address+0x1f0/0x3f0
[   40.610402][  T146]  ? __local_bh_enable_ip+0xe9/0x1b0
[   40.611071][  T146]  ? bond_hw_addr_flush+0x77/0x100 [bonding]
[   40.611823][  T146]  ? netdev_notify_peers+0xc0/0xc0
[   40.612461][  T146]  ? bond_hw_addr_flush+0x77/0x100 [bonding]
[   40.613213][  T146]  ? bond_hw_addr_flush+0x77/0x100 [bonding]
[   40.613963][  T146]  ? __local_bh_enable_ip+0xe9/0x1b0
[   40.614631][  T146]  ? bond_time_in_interval.isra.31+0x90/0x90 [bonding]
[   40.615484][  T146]  ? __bond_release_one+0x9f0/0x12c0 [bonding]
[   40.616230][  T146]  __bond_release_one+0x9f0/0x12c0 [bonding]
[   40.616949][  T146]  ? bond_enslave+0x47c0/0x47c0 [bonding]
[   40.617642][  T146]  ? lock_downgrade+0x730/0x730
[   40.618218][  T146]  ? check_flags.part.42+0x450/0x450
[   40.618850][  T146]  ? __mutex_unlock_slowpath+0xd0/0x670
[   40.619519][  T146]  ? trace_hardirqs_on+0x30/0x180
[   40.620117][  T146]  ? wait_for_completion+0x250/0x250
[   40.620754][  T146]  bond_netdev_event+0x822/0x970 [bonding]
[   40.621460][  T146]  ? __module_text_address+0x13/0x140
[   40.622097][  T146]  notifier_call_chain+0x90/0x160
[   40.622806][  T146]  rollback_registered_many+0x660/0xcf0
[   40.623522][  T146]  ? netif_set_real_num_tx_queues+0x780/0x780
[   40.624290][  T146]  ? notifier_call_chain+0x90/0x160
[   40.624957][  T146]  ? netdev_upper_dev_unlink+0x114/0x180
[   40.625686][  T146]  ? __netdev_adjacent_dev_unlink_neighbour+0x30/0x30
[   40.626421][  T146]  ? mutex_is_locked+0x13/0x50
[   40.627016][  T146]  ? unregister_netdevice_queue+0xf2/0x240
[   40.627663][  T146]  unregister_netdevice_many.part.134+0x13/0x1b0
[   40.628362][  T146]  default_device_exit_batch+0x2d9/0x390
[   40.628987][  T146]  ? unregister_netdevice_many+0x40/0x40
[   40.629615][  T146]  ? dev_change_net_namespace+0xcb0/0xcb0
[   40.630279][  T146]  ? prepare_to_wait_exclusive+0x2e0/0x2e0
[   40.630943][  T146]  ? ops_exit_list.isra.9+0x97/0x140
[   40.631554][  T146]  cleanup_net+0x441/0x890
[ ... ]

Fixes: e289fd28176b ("macvlan: fix the problem when mac address changes for passthru mode")
Reported-by: syzbot+5035b1f9dc7ea4558d5a@syzkaller.appspotmail.com
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

macsec: avoid to set wrong mtu

[ Upstream commit 7f327080364abccf923fa5a5b24e038eb0ba1407 ]

When a macsec interface is created, the mtu is calculated with the lower
interface's mtu value.
If the mtu of lower interface is lower than the length, which is needed
by macsec interface, macsec's mtu value will be overflowed.
So, if the lower interface's mtu is too low, macsec interface's mtu
should be set to 0.

Test commands:
    ip link add dummy0 mtu 10 type dummy
    ip link add macsec0 link dummy0 type macsec
    ip link show macsec0

Before:
    11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 4294967274
After:
    11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 0

Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: fix restrict IPV6_ADDRFORM operation

[ Upstream commit 82c9ae440857840c56e05d4fb1427ee032531346 ]

Commit b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.

Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.

Fixes: b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxgb4: fix large delays in PTP synchronization

[ Upstream commit bd019427bf3623ee3c7d2845cf921bbf4c14846c ]

Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.

Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, slub: restore the original intention of prefetch_freepointer()

commit 0882ff9190e3bc51e2d78c3aadd7c690eeaa91d5 upstream.

In SLUB, prefetch_freepointer() is used when allocating an object from
cache's freelist, to make sure the next object in the list is cache-hot,
since it's probable it will be allocated soon.

Commit 2482ddec670f ("mm: add SLUB free list pointer obfuscation") has
unintentionally changed the prefetch in a way where the prefetch is
turned to a real fetch, and only the next->next pointer is prefetched.
In case there is not a stream of allocations that would benefit from
prefetching, the extra real fetch might add a useless cache miss to the
allocation.  Restore the previous behavior.

Link: http://lkml.kernel.org/r/20180809085245.22448-1-vbabka@suse.cz
Fixes: 2482ddec670f ("mm: add SLUB free list pointer obfuscation")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI/ASPM: Allow re-enabling Clock PM

[ Upstream commit 35efea32b26f9aacc99bf07e0d2cdfba2028b099 ]

Previously Clock PM could not be re-enabled after being disabled by
pci_disable_link_state() because clkpm_capable was reset.  Change this by
adding a clkpm_disable field similar to aspm_disable.

Link: https://lore.kernel.org/r/4e8a66db-7d53-4a66-c26c-f0037ffaa705@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf/core: Disable page faults when getting phys address

[ Upstream commit d3296fb372bf7497b0e5d0478c4e7a677ec6f6e9 ]

We hit following warning when running tests on kernel
compiled with CONFIG_DEBUG_ATOMIC_SLEEP=y:

 WARNING: CPU: 19 PID: 4472 at mm/gup.c:2381 __get_user_pages_fast+0x1a4/0x200
 CPU: 19 PID: 4472 Comm: dummy Not tainted 5.6.0-rc6+ #3
 RIP: 0010:__get_user_pages_fast+0x1a4/0x200
 ...
 Call Trace:
  perf_prepare_sample+0xff1/0x1d90
  perf_event_output_forward+0xe8/0x210
  __perf_event_overflow+0x11a/0x310
  __intel_pmu_pebs_event+0x657/0x850
  intel_pmu_drain_pebs_nhm+0x7de/0x11d0
  handle_pmi_common+0x1b2/0x650
  intel_pmu_handle_irq+0x17b/0x370
  perf_event_nmi_handler+0x40/0x60
  nmi_handle+0x192/0x590
  default_do_nmi+0x6d/0x150
  do_nmi+0x2f9/0x3c0
  nmi+0x8e/0xd7

While __get_user_pages_fast() is IRQ-safe, it calls access_ok(),
which warns on:

  WARN_ON_ONCE(!in_task() && !pagefault_disabled())

Peter suggested disabling page faults around __get_user_pages_fast(),
which gets rid of the warning in access_ok() call.

Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200407141427.3184722-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: bcm2835: Dynamically allocate base

[ Upstream commit 2c25b07e5ec119cab609e41407a1fb3fa61442f5 ]

The newer 2711 and 7211 chips have two PWM controllers and failure to
dynamically allocate the PWM base would prevent the second PWM
controller instance being probed for succeeding with an -EEXIST error
from alloc_pwms().

Fixes: e5a06dc5ac1f ("pwm: Add BCM2835 PWM driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: renesas-tpu: Fix late Runtime PM enablement

[ Upstream commit d5a3c7a4536e1329a758e14340efd0e65252bd3d ]

Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should always be disabled after the removal of the
PWM chip, even if the latter failed.

Fixes: 99b82abb0a35b073 ("pwm: Add Renesas TPU PWM driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/cio: avoid duplicated 'ADD' uevents

[ Upstream commit 05ce3e53f375295c2940390b2b429e506e07655c ]

The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The io_subchannel driver will do so when the associated
ccw_device has been registered -- but unconditionally, so more
ADD uevents will be generated if a subchannel has been unbound
from the io_subchannel driver and later rebound.

To fix this, only generate the ADD event if uevents were still
suppressed for the device.

Fixes: fa1a8c23eb7d ("s390: cio: Delay uevents for subchannels")
Message-Id: <20200327124503.9794-2-cohuck@redhat.com>
Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipc/util.c: sysvipc_find_ipc() should increase position index

[ Upstream commit 89163f93c6f969da5811af5377cc10173583123b ]

If seq_file .next function does not change position index, read after
some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Waiman Long <longman@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: NeilBrown <neilb@suse.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/b7a20945-e315-8bb0-21e6-3875c14a8494@virtuozzo.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: kmod: fix handling test numbers above 9

[ Upstream commit 6d573a07528308eb77ec072c010819c359bebf6e ]

get_test_count() and get_test_enabled() were broken for test numbers
above 9 due to awk interpreting a field specification like '$0010' as
octal rather than decimal.  Fix it by stripping the leading zeroes.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: NeilBrown <neilb@suse.com>
Link: http://lkml.kernel.org/r/20200318230515.171692-5-ebiggers@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernel/gcov/fs.c: gcov_seq_next() should increase position index

[ Upstream commit f4d74ef6220c1eda0875da30457bef5c7111ab06 ]

If seq_file .next function does not change position index, read after
some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: NeilBrown <neilb@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Waiman Long <longman@redhat.com>
Link: http://lkml.kernel.org/r/f65c6ee7-bd00-f910-2f8a-37cc67e4ff88@virtuozzo.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Intel: atom: Take the drv->lock mutex before calling sst_send_slot_map()

[ Upstream commit 81630dc042af998b9f58cd8e2c29dab9777ea176 ]

sst_send_slot_map() uses sst_fill_and_send_cmd_unlocked() because in some
places it is called with the drv->lock mutex already held.

So it must always be called with the mutex locked. This commit adds missing
locking in the sst_set_be_modules() code-path.

Fixes: 24c8d14192cc ("ASoC: Intel: mrfld: add DSP core controls")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200402185359.3424-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: iscsi: Report unbind session event when the target has been removed

[ Upstream commit 13e60d3ba287d96eeaf1deaadba51f71578119a3 ]

If the daemon is restarted or crashes while logging out of a session, the
unbind session event sent by the kernel is not processed and is lost.  When
the daemon starts again, the session can't be unbound because the daemon is
waiting for the event message. However, the kernel has already logged out
and the event will not be resent.

When iscsid restart is complete, logout session reports error:

Logging out of session [sid: 6, target: iqn.xxxxx, portal: xx.xx.xx.xx,3260]
iscsiadm: Could not logout of [sid: 6, target: iscsiadm -m node iqn.xxxxx, portal: xx.xx.xx.xx,3260].
iscsiadm: initiator reported error (9 - internal error)
iscsiadm: Could not logout of all requested sessions

Make sure the unbind event is emitted.

[mkp: commit desc and applied by hand since patch was mangled]

Link: https://lore.kernel.org/r/4eab1771-2cb3-8e79-b31c-923652340e99@huawei.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: rcar: Fix late Runtime PM enablement

[ Upstream commit 1451a3eed24b5fd6a604683f0b6995e0e7e16c79 ]

Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should be disabled after the removal of the PWM
chip.

Fixes: ed6c1476bf7f16d5 ("pwm: Add support for R-Car PWM Timer")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: don't skip updating wanted caps when cap is stale

[ Upstream commit 0aa971b6fd3f92afef6afe24ef78d9bb14471519 ]

1. try_get_cap_refs() fails to get caps and finds that mds_wanted
   does not include what it wants. It returns -ESTALE.
2. ceph_get_caps() calls ceph_renew_caps(). ceph_renew_caps() finds
   that inode has cap, so it calls ceph_check_caps().
3. ceph_check_caps() finds that issued caps (without checking if it's
   stale) already includes caps wanted by open file, so it skips
   updating wanted caps.

Above events can cause an infinite loop inside ceph_get_caps().

Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: return ceph_mdsc_do_request() errors from __get_parent()

[ Upstream commit c6d50296032f0b97473eb2e274dc7cc5d0173847 ]

Return the error returned by ceph_mdsc_do_request(). Otherwise,
r_target_inode ends up being NULL this ends up returning ENOENT
regardless of the error.

Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Fix kasan slab-out-of-bounds error in lpfc_unreg_login

[ Upstream commit 38503943c89f0bafd9e3742f63f872301d44cbea ]

The following kasan bug was called out:

 BUG: KASAN: slab-out-of-bounds in lpfc_unreg_login+0x7c/0xc0 [lpfc]
 Read of size 2 at addr ffff889fc7c50a22 by task lpfc_worker_3/6676
 ...
 Call Trace:
 dump_stack+0x96/0xe0
 ? lpfc_unreg_login+0x7c/0xc0 [lpfc]
 print_address_description.constprop.6+0x1b/0x220
 ? lpfc_unreg_login+0x7c/0xc0 [lpfc]
 ? lpfc_unreg_login+0x7c/0xc0 [lpfc]
 __kasan_report.cold.9+0x37/0x7c
 ? lpfc_unreg_login+0x7c/0xc0 [lpfc]
 kasan_report+0xe/0x20
 lpfc_unreg_login+0x7c/0xc0 [lpfc]
 lpfc_sli_def_mbox_cmpl+0x334/0x430 [lpfc]
 ...

When processing the completion of a "Reg Rpi" login mailbox command in
lpfc_sli_def_mbox_cmpl, a call may be made to lpfc_unreg_login. The vpi is
extracted from the completing mailbox context and passed as an input for
the next. However, the vpi stored in the mailbox command context is an
absolute vpi, which for SLI4 represents both base + offset.  When used with
a non-zero base component, (function id > 0) this results in an
out-of-range access beyond the allocated phba->vpi_ids array.

Fix by subtracting the function's base value to get an accurate vpi number.

Link: https://lore.kernel.org/r/20200322181304.37655-2-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

watchdog: reset last_hw_keepalive time at start

[ Upstream commit 982bb70517aef2225bad1d802887b733db492cc0 ]

Currently the watchdog core does not initialize the last_hw_keepalive
time during watchdog startup. This will cause the watchdog to be pinged
immediately if enough time has passed from the system boot-up time, and
some types of watchdogs like K3 RTI does not like this.

To avoid the issue, setup the last_hw_keepalive time during watchdog
startup.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200302200426.6492-3-t-kristo@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vti4: removed duplicate log message.

commit 01ce31c57b3f07c91c9d45bbaf126124cce83a5d upstream.

Removed info log-message if ipip tunnel registration fails during
module-initialization: it adds nothing to the error message that is
written on all failures.

Fixes: dd9ee3444014e ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: mxs-dcp - make symbols 'sha1_null_hash' and 'sha256_null_hash' static

commit ce4e45842de3eb54b8dd6e081765d741f5b92b56 upstream.

Fixes the following sparse warnings:

drivers/crypto/mxs-dcp.c:39:15: warning:
 symbol 'sha1_null_hash' was not declared. Should it be static?
drivers/crypto/mxs-dcp.c:43:15: warning:
 symbol 'sha256_null_hash' was not declared. Should it be static?

Fixes: c709eebaf5c5 ("crypto: mxs-dcp - Fix SHA null hashes and output length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/msm: Use the correct dma_sync calls harder

commit 9f614197c744002f9968e82c649fdf7fe778e1e7 upstream.

Looks like the dma_sync calls don't do what we want on armv7 either.
Fixes:

  Unable to handle kernel paging request at virtual address 50001000
  pgd = (ptrval)
  [50001000] *pgd=00000000
  Internal error: Oops: 805 [#1] SMP ARM
  Modules linked in:
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.3.0-rc6-00271-g9f159ae07f07 #4
  Hardware name: Freescale i.MX53 (Device Tree Support)
  PC is at v7_dma_clean_range+0x20/0x38
  LR is at __dma_page_cpu_to_dev+0x28/0x90
  pc : [<c011c76c>]    lr : [<c01181c4>]    psr: 20000013
  sp : d80b5a88  ip : de96c000  fp : d840ce6c
  r10: 00000000  r9 : 00000001  r8 : d843e010
  r7 : 00000000  r6 : 00008000  r5 : ddb6c000  r4 : 00000000
  r3 : 0000003f  r2 : 00000040  r1 : 50008000  r0 : 50001000
  Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
  Control: 10c5387d  Table: 70004019  DAC: 00000051
  Process swapper/0 (pid: 1, stack limit = 0x(ptrval))

Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes: 3de433c5b38a ("drm/msm: Use the correct dma_sync calls in msm_gem")
Tested-by: Fabio Estevam <festevam@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

keys: Fix the use of the C++ keyword "private" in uapi/linux/keyctl.h

commit 2ecefa0a15fd0ef88b9cd5d15ceb813008136431 upstream.

The keyctl_dh_params struct in uapi/linux/keyctl.h contains the symbol
"private" which means that the header file will cause compilation failure
if #included in to a C++ program.  Further, the patch that added the same
struct to the keyutils package named the symbol "priv", not "private".

The previous attempt to fix this (commit 8a2336e549d3) did so by simply
renaming the kernel's copy of the field to dh_private, but this then breaks
existing userspace and as such has been reverted (commit 8c0f9f5b309d).

[And note, to those who think that wrapping the struct in extern "C" {}
 will work: it won't; that only changes how symbol names are presented to
 the assembler and linker.].

Instead, insert an anonymous union around the "private" member and add a
second member in there with the name "priv" to match the one in the
keyutils package.  The "private" member is then wrapped in !__cplusplus
cpp-conditionals to hide it from C++.

Fixes: ddbb41148724 ("KEYS: Add KEYCTL_DH_COMPUTE command")
Fixes: 8a2336e549d3 ("uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: Lubomir Rintel <lkundrak@v3.sk>
cc: James Morris <jmorris@namei.org>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.morris@microsoft.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv4: avoid unused variable warning for sysctl

commit 773daa3caf5d3f87fdb1ab43e9c1b367a38fa394 upstream.

The newly introudced ip_min_valid_pmtu variable is only used when
CONFIG_SYSCTL is set:

net/ipv4/route.c:135:12: error: 'ip_min_valid_pmtu' defined but not used [-Werror=unused-variable]

This moves it to the other variables like it, to avoid the harmless
warning.

Fixes: c7272c2f1229 ("net: ipv4: don't allow setting net.ipv4.route.min_pmtu below 68")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv4: emulate READ_ONCE() on ->hdrincl bit-field in raw_sendmsg()

commit 20b50d79974ea3192e8c3ab7faf4e536e5f14d8f upstream.

Commit 8f659a03a0ba ("net: ipv4: fix for a race condition in
raw_sendmsg") fixed the issue of possibly inconsistent ->hdrincl handling
due to concurrent updates by reading this bit-field member into a local
variable and using the thus stabilized value in subsequent tests.

However, aforementioned commit also adds the (correct) comment that

  /* hdrincl should be READ_ONCE(inet->hdrincl)
   * but READ_ONCE() doesn't work with bit fields
   */

because as it stands, the compiler is free to shortcut or even eliminate
the local variable at its will.

Note that I have not seen anything like this happening in reality and thus,
the concern is a theoretical one.

However, in order to be on the safe side, emulate a READ_ONCE() on the
bit-field by doing it on the local 'hdrincl' variable itself:

int hdrincl = inet->hdrincl;
hdrincl = READ_ONCE(hdrincl);

This breaks the chain in the sense that the compiler is not allowed
to replace subsequent reads from hdrincl with reloads from inet->hdrincl.

Fixes: 8f659a03a0ba ("net: ipv4: fix for a race condition in raw_sendmsg")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix extent_status fragmentation for plain files

commit 4068664e3cd2312610ceac05b74c4cf1853b8325 upstream.

Extents are cached in read_extent_tree_block(); as a result, extents
are not cached for inodes with depth == 0 when we try to find the
extent using ext4_find_extent().  The result of the lookup is cached
in ext4_map_blocks() but is only a subset of the extent on disk.  As a
result, the contents of extents status cache can get very badly
fragmented for certain workloads, such as a random 4k read workload.

File size of /mnt/test is 33554432 (8192 blocks of 4096 bytes)
 ext:     logical_offset:        physical_offset: length:   expected: flags:
   0:        0..    8191:      40960..     49151:   8192:             last,eof

$ perf record -e 'ext4:ext4_es_*' /root/bin/fio --name=t --direct=0 --rw=randread --bs=4k --filesize=32M --size=32M --filename=/mnt/test
$ perf script | grep ext4_es_insert_extent | head -n 10
             fio   131 [000]    13.975421:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [494/1) mapped 41454 status W
             fio   131 [000]    13.975939:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6064/1) mapped 47024 status W
             fio   131 [000]    13.976467:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6907/1) mapped 47867 status W
             fio   131 [000]    13.976937:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3850/1) mapped 44810 status W
             fio   131 [000]    13.977440:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3292/1) mapped 44252 status W
             fio   131 [000]    13.977931:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6882/1) mapped 47842 status W
             fio   131 [000]    13.978376:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3117/1) mapped 44077 status W
             fio   131 [000]    13.978957:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [2896/1) mapped 43856 status W
             fio   131 [000]    13.979474:           ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [7479/1) mapped 48439 status W

Fix this by caching the extents for inodes with depth == 0 in
ext4_find_extent().

[ Renamed ext4_es_cache_extents() to ext4_cache_extents() since this
  newly added function is not in extents_cache.c, and to avoid
  potential visual confusion with ext4_es_cache_extent().  -TYT ]

Signed-off-by: Dmitry Monakhov <dmonakhov@gmail.com>
Link: https://lore.kernel.org/r/20191106122502.19986-1-dmonakhov@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.177

KEYS: Don't write out to userspace while holding key semaphore

commit d3ec10aa95819bff18a0d936b18884c7816d0914 upstream.

A lockdep circular locking dependency report was seen when running a
keyutils test:

[12537.027242] ======================================================
[12537.059309] WARNING: possible circular locking dependency detected
[12537.088148] 4.18.0-147.7.1.el8_1.x86_64+debug #1 Tainted: G OE    --------- -  -
[12537.125253] ------------------------------------------------------
[12537.153189] keyctl/25598 is trying to acquire lock:
[12537.175087] 000000007c39f96c (&mm->mmap_sem){++++}, at: __might_fault+0xc4/0x1b0
[12537.208365]
[12537.208365] but task is already holding lock:
[12537.234507] 000000003de5b58d (&type->lock_class){++++}, at: keyctl_read_key+0x15a/0x220
[12537.270476]
[12537.270476] which lock already depends on the new lock.
[12537.270476]
[12537.307209]
[12537.307209] the existing dependency chain (in reverse order) is:
[12537.340754]
[12537.340754] -> #3 (&type->lock_class){++++}:
[12537.367434]        down_write+0x4d/0x110
[12537.385202]        __key_link_begin+0x87/0x280
[12537.405232]        request_key_and_link+0x483/0xf70
[12537.427221]        request_key+0x3c/0x80
[12537.444839]        dns_query+0x1db/0x5a5 [dns_resolver]
[12537.468445]        dns_resolve_server_name_to_ip+0x1e1/0x4d0 [cifs]
[12537.496731]        cifs_reconnect+0xe04/0x2500 [cifs]
[12537.519418]        cifs_readv_from_socket+0x461/0x690 [cifs]
[12537.546263]        cifs_read_from_socket+0xa0/0xe0 [cifs]
[12537.573551]        cifs_demultiplex_thread+0x311/0x2db0 [cifs]
[12537.601045]        kthread+0x30c/0x3d0
[12537.617906]        ret_from_fork+0x3a/0x50
[12537.636225]
[12537.636225] -> #2 (root_key_user.cons_lock){+.+.}:
[12537.664525]        __mutex_lock+0x105/0x11f0
[12537.683734]        request_key_and_link+0x35a/0xf70
[12537.705640]        request_key+0x3c/0x80
[12537.723304]        dns_query+0x1db/0x5a5 [dns_resolver]
[12537.746773]        dns_resolve_server_name_to_ip+0x1e1/0x4d0 [cifs]
[12537.775607]        cifs_reconnect+0xe04/0x2500 [cifs]
[12537.798322]        cifs_readv_from_socket+0x461/0x690 [cifs]
[12537.823369]        cifs_read_from_socket+0xa0/0xe0 [cifs]
[12537.847262]        cifs_demultiplex_thread+0x311/0x2db0 [cifs]
[12537.873477]        kthread+0x30c/0x3d0
[12537.890281]        ret_from_fork+0x3a/0x50
[12537.908649]
[12537.908649] -> #1 (&tcp_ses->srv_mutex){+.+.}:
[12537.935225]        __mutex_lock+0x105/0x11f0
[12537.954450]        cifs_call_async+0x102/0x7f0 [cifs]
[12537.977250]        smb2_async_readv+0x6c3/0xc90 [cifs]
[12538.000659]        cifs_readpages+0x120a/0x1e50 [cifs]
[12538.023920]        read_pages+0xf5/0x560
[12538.041583]        __do_page_cache_readahead+0x41d/0x4b0
[12538.067047]        ondemand_readahead+0x44c/0xc10
[12538.092069]        filemap_fault+0xec1/0x1830
[12538.111637]        __do_fault+0x82/0x260
[12538.129216]        do_fault+0x419/0xfb0
[12538.146390]        __handle_mm_fault+0x862/0xdf0
[12538.167408]        handle_mm_fault+0x154/0x550
[12538.187401]        __do_page_fault+0x42f/0xa60
[12538.207395]        do_page_fault+0x38/0x5e0
[12538.225777]        page_fault+0x1e/0x30
[12538.243010]
[12538.243010] -> #0 (&mm->mmap_sem){++++}:
[12538.267875]        lock_acquire+0x14c/0x420
[12538.286848]        __might_fault+0x119/0x1b0
[12538.306006]        keyring_read_iterator+0x7e/0x170
[12538.327936]        assoc_array_subtree_iterate+0x97/0x280
[12538.352154]        keyring_read+0xe9/0x110
[12538.370558]        keyctl_read_key+0x1b9/0x220
[12538.391470]        do_syscall_64+0xa5/0x4b0
[12538.410511]        entry_SYSCALL_64_after_hwframe+0x6a/0xdf
[12538.435535]
[12538.435535] other info that might help us debug this:
[12538.435535]
[12538.472829] Chain exists of:
[12538.472829]   &mm->mmap_sem --> root_key_user.cons_lock --> &type->lock_class
[12538.472829]
[12538.524820]  Possible unsafe locking scenario:
[12538.524820]
[12538.551431]        CPU0                    CPU1
[12538.572654]        ----                    ----
[12538.595865]   lock(&type->lock_class);
[12538.613737]                                lock(root_key_user.cons_lock);
[12538.644234]                                lock(&type->lock_class);
[12538.672410]   lock(&mm->mmap_sem);
[12538.687758]
[12538.687758]  *** DEADLOCK ***
[12538.687758]
[12538.714455] 1 lock held by keyctl/25598:
[12538.732097]  #0: 000000003de5b58d (&type->lock_class){++++}, at: keyctl_read_key+0x15a/0x220
[12538.770573]
[12538.770573] stack backtrace:
[12538.790136] CPU: 2 PID: 25598 Comm: keyctl Kdump: loaded Tainted: G
[12538.844855] Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9, BIOS P89 12/27/2015
[12538.881963] Call Trace:
[12538.892897]  dump_stack+0x9a/0xf0
[12538.907908]  print_circular_bug.isra.25.cold.50+0x1bc/0x279
[12538.932891]  ? save_trace+0xd6/0x250
[12538.948979]  check_prev_add.constprop.32+0xc36/0x14f0
[12538.971643]  ? keyring_compare_object+0x104/0x190
[12538.992738]  ? check_usage+0x550/0x550
[12539.009845]  ? sched_clock+0x5/0x10
[12539.025484]  ? sched_clock_cpu+0x18/0x1e0
[12539.043555]  __lock_acquire+0x1f12/0x38d0
[12539.061551]  ? trace_hardirqs_on+0x10/0x10
[12539.080554]  lock_acquire+0x14c/0x420
[12539.100330]  ? __might_fault+0xc4/0x1b0
[12539.119079]  __might_fault+0x119/0x1b0
[12539.135869]  ? __might_fault+0xc4/0x1b0
[12539.153234]  keyring_read_iterator+0x7e/0x170
[12539.172787]  ? keyring_read+0x110/0x110
[12539.190059]  assoc_array_subtree_iterate+0x97/0x280
[12539.211526]  keyring_read+0xe9/0x110
[12539.227561]  ? keyring_gc_check_iterator+0xc0/0xc0
[12539.249076]  keyctl_read_key+0x1b9/0x220
[12539.266660]  do_syscall_64+0xa5/0x4b0
[12539.283091]  entry_SYSCALL_64_after_hwframe+0x6a/0xdf

One way to prevent this deadlock scenario from happening is to not
allow writing to userspace while holding the key semaphore. Instead,
an internal buffer is allocated for getting the keys out from the
read method first before copying them out to userspace without holding
the lock.

That requires taking out the __user modifier from all the relevant
read methods as well as additional changes to not use any userspace
write helpers. That is,

  1) The put_user() call is replaced by a direct copy.
  2) The copy_to_user() call is replaced by memcpy().
  3) All the fault handling code is removed.

Compiling on a x86-64 system, the size of the rxrpc_read() function is
reduced from 3795 bytes to 2384 bytes with this patch.

Fixes: ^1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: Use individual pages in big_key for crypto buffers

commit d9f4bb1a0f4db493efe6d7c58ffe696a57de7eb3 upstream.

kmalloc() can't always allocate large enough buffers for big_key to use for
crypto (1MB + some metadata) so we cannot use that to allocate the buffer.
Further, vmalloc'd pages can't be passed to sg_init_one() and the aead
crypto accessors cannot be called progressively and must be passed all the
data in one go (which means we can't pass the data in one block at a time).

Fix this by allocating the buffer pages individually and passing them
through a multientry scatterlist to the crypto layer.  This has the bonus
advantage that we don't have to allocate a contiguous series of pages.

We then vmap() the page list and pass that through to the VFS read/write
routines.

This can trigger a warning:

WARNING: CPU: 0 PID: 60912 at mm/page_alloc.c:3883 __alloc_pages_nodemask+0xb7c/0x15f8
([<00000000002acbb6>] __alloc_pages_nodemask+0x1ee/0x15f8)
 [<00000000002dd356>] kmalloc_order+0x46/0x90
 [<00000000002dd3e0>] kmalloc_order_trace+0x40/0x1f8
 [<0000000000326a10>] __kmalloc+0x430/0x4c0
 [<00000000004343e4>] big_key_preparse+0x7c/0x210
 [<000000000042c040>] key_create_or_update+0x128/0x420
 [<000000000042e52c>] SyS_add_key+0x124/0x220
 [<00000000007bba2c>] system_call+0xc4/0x2b0

from the keyctl/padd/useradd test of the keyutils testsuite on s390x.

Note that it might be better to shovel data through in page-sized lumps
instead as there's no particular need to use a monolithic buffer unless the
kernel itself wants to access the data.

Fixes: 13100a72f40f ("Security: Keys: Big keys stored encrypted")
Reported-by: Paul Bunyan <pbunyan@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Kirill Marinushkin <k.marinushkin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: phram: fix a double free issue in error path

commit 49c64df880570034308e4a9a49c4bc95cf8cdb33 upstream.

The variable 'name' is released multiple times in the error path,
which may cause double free issues.
This problem is avoided by adding a goto label to release the memory
uniformly. And this change also makes the code a bit more cleaner.

Fixes: 4f678a58d335 ("mtd: fix memory leaks in phram_setup")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Joern Engel <joern@lazybastard.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200318153156.25612-1-wenyang@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: lpddr: Fix a double free in probe()

commit 4da0ea71ea934af18db4c63396ba2af1a679ef02 upstream.

This function is only called from lpddr_probe().  We free "lpddr" both
here and in the caller, so it's a double free.  The best place to free
"lpddr" is in lpddr_probe() so let's delete this one.

Fixes: 8dc004395d5e ("[MTD] LPDDR qinfo probing.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200228092554.o57igp3nqhyvf66t@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locktorture: Print ratio of acquisitions, not failures

commit 80c503e0e68fbe271680ab48f0fe29bc034b01b7 upstream.

The __torture_print_stats() function in locktorture.c carefully
initializes local variable "min" to statp[0].n_lock_acquired, but
then compares it to statp[i].n_lock_fail.  Given that the .n_lock_fail
field should normally be zero, and given the initialization, it seems
reasonable to display the maximum and minimum number acquisitions
instead of miscomputing the maximum and minimum number of failures.
This commit therefore switches from failures to acquisitions.

And this turns out to be not only a day-zero bug, but entirely my
own fault.  I hate it when that happens!

Fixes: 0af3fe1efa53 ("locktorture: Add a lock-torture kernel module")
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: evh_bytechan: Fix out of bounds accesses

commit 3670664b5da555a2a481449b3baafff113b0ac35 upstream.

ev_byte_channel_send() assumes that its third argument is a 16 byte
array. Some places where it is called it may not be (or we can't
easily tell if it is). Newer compilers have started producing warnings
about this, so make sure we actually pass a 16 byte array.

There may be more elegant solutions to this, but the driver is quite
old and hasn't been updated in many years.

The warnings (from a powerpc allyesconfig build) are:

  In file included from include/linux/byteorder/big_endian.h:5,
                   from arch/powerpc/include/uapi/asm/byteorder.h:14,
                   from include/asm-generic/bitops/le.h:6,
                   from arch/powerpc/include/asm/bitops.h:250,
                   from include/linux/bitops.h:29,
                   from include/linux/kernel.h:12,
                   from include/asm-generic/bug.h:19,
                   from arch/powerpc/include/asm/bug.h:109,
                   from include/linux/bug.h:5,
                   from include/linux/mmdebug.h:5,
                   from include/linux/gfp.h:5,
                   from include/linux/slab.h:15,
                   from drivers/tty/ehv_bytechan.c:24:
  drivers/tty/ehv_bytechan.c: In function ‘ehv_bc_udbg_putc’:
  arch/powerpc/include/asm/epapr_hcalls.h:298:20: warning: array subscript 1 is outside array bounds of ‘const char[1]’ [-Warray-bounds]
    298 |  r6 = be32_to_cpu(p[1]);
  include/uapi/linux/byteorder/big_endian.h:40:51: note: in definition of macro ‘__be32_to_cpu’
     40 | #define __be32_to_cpu(x) ((__force __u32)(__be32)(x))
        |                                                   ^
  arch/powerpc/include/asm/epapr_hcalls.h:298:7: note: in expansion of macro ‘be32_to_cpu’
    298 |  r6 = be32_to_cpu(p[1]);
        |       ^~~~~~~~~~~
  drivers/tty/ehv_bytechan.c:166:13: note: while referencing ‘data’
    166 | static void ehv_bc_udbg_putc(char c)
        |             ^~~~~~~~~~~~~~~~

Fixes: dcd83aaff1c8 ("tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[mpe: Trim warnings from change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200109183912.5fcb52aa@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: potential information leak in do_fb_ioctl()

commit d3d19d6fc5736a798b118971935ce274f7deaa82 upstream.

The "fix" struct has a 2 byte hole after ->ywrapstep and the
"fix = info->fix;" assignment doesn't necessarily clear it.  It depends
on the compiler.  The solution is just to replace the assignment with an
memcpy().

Fixes: 1f5e31d7e55a ("fbmem: don't call copy_from/to_user() with mutex held")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andrea Righi <righi.andrea@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113100132.ixpaymordi24n3av@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: bcm_sf2: Fix overflow checks

commit d0802dc411f469569a537283b6f3833af47aece9 upstream.

Commit f949a12fd697 ("net: dsa: bcm_sf2: fix buffer overflow doing
set_rxnfc") tried to fix the some user controlled buffer overflows in
bcm_sf2_cfp_rule_set() and bcm_sf2_cfp_rule_del() but the fix was using
CFP_NUM_RULES, which while it is correct not to overflow the bitmaps, is
not representative of what the device actually supports. Correct that by
using bcm_sf2_cfp_rule_size() instead.

The latter subtracts the number of rules by 1, so change the checks from
greater than or equal to greater than accordingly.

Fixes: f949a12fd697 ("net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/amd: Fix the configuration of GCR3 table root pointer

[ Upstream commit c20f36534666e37858a14e591114d93cc1be0d34 ]

The SPA of the GCR3 table root pointer[51:31] masks 20 bits. However,
this requires 21 bits (Please see the AMD IOMMU specification).
This leads to the potential failure when the bit 51 of SPA of
the GCR3 table root pointer is 1'.

Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Fixes: 52815b75682e2 ("iommu/amd: Add support for IOMMUv2 domain mode")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

libnvdimm: Out of bounds read in __nd_ioctl()

[ Upstream commit f84afbdd3a9e5e10633695677b95422572f920dc ]

The "cmd" comes from the user and it can be up to 255.  It it's more
than the number of bits in long, it results out of bounds read when we
check test_bit(cmd, &cmd_mask).  The highest valid value for "cmd" is
ND_CMD_CALL (10) so I added a compare against that.

Fixes: 62232e45f4a2 ("libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200225162055.amtosfy7m35aivxg@kili.mountain
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext2: fix debug reference to ext2_xattr_cache

[ Upstream commit 32302085a8d90859c40cf1a5e8313f575d06ec75 ]

Fix a debug-only build error in ext2/xattr.c:

When building without extra debugging, (and with another patch that uses
no_printk() instead of <empty> for the ext2-xattr debug-print macros,
this build error happens:

../fs/ext2/xattr.c: In function ‘ext2_xattr_cache_insert’:
../fs/ext2/xattr.c:869:18: error: ‘ext2_xattr_cache’ undeclared (first use in
this function); did you mean ‘ext2_xattr_list’?
     atomic_read(&ext2_xattr_cache->c_entry_count));

Fix the problem by removing cached entry count from the debug message
since otherwise we'd have to export the mbcache structure just for that.

Fixes: be0726d33cb8 ("ext2: convert to mbcache2")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext2: fix empty body warnings when -Wextra is used

[ Upstream commit 44a52022e7f15cbaab957df1c14f7a4f527ef7cf ]

When EXT2_ATTR_DEBUG is not defined, modify the 2 debug macros
to use the no_printk() macro instead of <nothing>.
This fixes gcc warnings when -Wextra is used:

../fs/ext2/xattr.c:252:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../fs/ext2/xattr.c:258:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../fs/ext2/xattr.c:330:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../fs/ext2/xattr.c:872:45: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]

I have verified that the only object code change (with gcc 7.5.0) is
the reversal of some instructions from 'cmp a,b' to 'cmp b,a'.

Link: https://lore.kernel.org/r/e18a7395-61fb-2093-18e8-ed4f8cf56248@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jan Kara <jack@suse.com>
Cc: linux-ext4@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/vt-d: Fix mm reference leak

[ Upstream commit 902baf61adf6b187f0a6b789e70d788ea71ff5bc ]

Move canonical address check before mmget_not_zero() to avoid mm
reference leak.

Fixes: 9d8c3af31607 ("iommu/vt-d: IOMMU Page Request needs to check if address is canonical.")
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFS: Fix memory leaks in nfs_pageio_stop_mirroring()

[ Upstream commit 862f35c94730c9270833f3ad05bd758a29f204ed ]

If we just set the mirror count to 1 without first clearing out
the mirrors, we can leak queued up requests.

Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: kfree the wrong pointer

[ Upstream commit 3148a6a0ef3cf93570f30a477292768f7eb5d3c3 ]

Originally, it kfrees the wrong pointer for mem_obj.
It would cause memory leak under stress test.

Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86: ACPI: fix CPU hotplug deadlock

[ Upstream commit 696ac2e3bf267f5a2b2ed7d34e64131f2287d0ad ]

Similar to commit 0266d81e9bf5 ("acpi/processor: Prevent cpu hotplug
deadlock") except this is for acpi_processor_ffh_cstate_probe():

"The problem is that the work is scheduled on the current CPU from the
hotplug thread associated with that CPU.

It's not required to invoke these functions via the workqueue because
the hotplug thread runs on the target CPU already.

Check whether current is a per cpu thread pinned on the target CPU and
invoke the function directly to avoid the workqueue."

 WARNING: possible circular locking dependency detected
 ------------------------------------------------------
 cpuhp/1/15 is trying to acquire lock:
 ffffc90003447a28 ((work_completion)(&wfc.work)){+.+.}-{0:0}, at: __flush_work+0x4c6/0x630

 but task is already holding lock:
 ffffffffafa1c0e8 (cpuidle_lock){+.+.}-{3:3}, at: cpuidle_pause_and_lock+0x17/0x20

 which lock already depends on the new lock.

 the existing dependency chain (in reverse order) is:

 -> #1 (cpu_hotplug_lock){++++}-{0:0}:
 cpus_read_lock+0x3e/0xc0
 irq_calc_affinity_vectors+0x5f/0x91
 __pci_enable_msix_range+0x10f/0x9a0
 pci_alloc_irq_vectors_affinity+0x13e/0x1f0
 pci_alloc_irq_vectors_affinity at drivers/pci/msi.c:1208
 pqi_ctrl_init+0x72f/0x1618 [smartpqi]
 pqi_pci_probe.cold.63+0x882/0x892 [smartpqi]
 local_pci_probe+0x7a/0xc0
 work_for_cpu_fn+0x2e/0x50
 process_one_work+0x57e/0xb90
 worker_thread+0x363/0x5b0
 kthread+0x1f4/0x220
 ret_from_fork+0x27/0x50

 -> #0 ((work_completion)(&wfc.work)){+.+.}-{0:0}:
 __lock_acquire+0x2244/0x32a0
 lock_acquire+0x1a2/0x680
 __flush_work+0x4e6/0x630
 work_on_cpu+0x114/0x160
 acpi_processor_ffh_cstate_probe+0x129/0x250
 acpi_processor_evaluate_cst+0x4c8/0x580
 acpi_processor_get_power_info+0x86/0x740
 acpi_processor_hotplug+0xc3/0x140
 acpi_soft_cpu_online+0x102/0x1d0
 cpuhp_invoke_callback+0x197/0x1120
 cpuhp_thread_fun+0x252/0x2f0
 smpboot_thread_fn+0x255/0x440
 kthread+0x1f4/0x220
 ret_from_fork+0x27/0x50

 other info that might help us debug this:

 Chain exists of:
 (work_completion)(&wfc.work) --> cpuhp_state-up --> cpuidle_lock

 Possible unsafe locking scenario:

 CPU0                    CPU1
 ----                    ----
 lock(cpuidle_lock);
                         lock(cpuhp_state-up);
                         lock(cpuidle_lock);
 lock((work_completion)(&wfc.work));

 *** DEADLOCK ***

 3 locks held by cpuhp/1/15:
 #0: ffffffffaf51ab10 (cpu_hotplug_lock){++++}-{0:0}, at: cpuhp_thread_fun+0x69/0x2f0
 #1: ffffffffaf51ad40 (cpuhp_state-up){+.+.}-{0:0}, at: cpuhp_thread_fun+0x69/0x2f0
 #2: ffffffffafa1c0e8 (cpuidle_lock){+.+.}-{3:3}, at: cpuidle_pause_and_lock+0x17/0x20

 Call Trace:
 dump_stack+0xa0/0xea
 print_circular_bug.cold.52+0x147/0x14c
 check_noncircular+0x295/0x2d0
 __lock_acquire+0x2244/0x32a0
 lock_acquire+0x1a2/0x680
 __flush_work+0x4e6/0x630
 work_on_cpu+0x114/0x160
 acpi_processor_ffh_cstate_probe+0x129/0x250
 acpi_processor_evaluate_cst+0x4c8/0x580
 acpi_processor_get_power_info+0x86/0x740
 acpi_processor_hotplug+0xc3/0x140
 acpi_soft_cpu_online+0x102/0x1d0
 cpuhp_invoke_callback+0x197/0x1120
 cpuhp_thread_fun+0x252/0x2f0
 smpboot_thread_fn+0x255/0x440
 kthread+0x1f4/0x220
 ret_from_fork+0x27/0x50

Signed-off-by: Qian Cai <cai@lca.pw>
Tested-by: Borislav Petkov <bp@suse.de>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: s390: vsie: Fix possible race when shadowing region 3 tables

[ Upstream commit 1493e0f944f3c319d11e067c185c904d01c17ae5 ]

We have to properly retry again by returning -EINVAL immediately in case
somebody else instantiated the table concurrently. We missed to add the
goto in this function only. The code now matches the other, similar
shadowing functions.

We are overwriting an existing region 2 table entry. All allocated pages
are added to the crst_list to be freed later, so they are not lost
forever. However, when unshadowing the region 2 table, we wouldn't trigger
unshadowing of the original shadowed region 3 table that we replaced. It
would get unshadowed when the original region 3 table is modified. As it's
not connected to the page table hierarchy anymore, it's not going to get
used anymore. However, for a limited time, this page table will stick
around, so it's in some sense a temporary memory leak.

Identified by manual code inspection. I don't think this classifies as
stable material.

Fixes: 998f637cc4b9 ("s390/mm: avoid races on region/segment/page table shadowing")
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200403153050.20569-4-david@redhat.com
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

compiler.h: fix error in BUILD_BUG_ON() reporting

[ Upstream commit af9c5d2e3b355854ff0e4acfbfbfadcd5198a349 ]

compiletime_assert() uses __LINE__ to create a unique function name.  This
means that if you have more than one BUILD_BUG_ON() in the same source
line (which can happen if they appear e.g.  in a macro), then the error
message from the compiler might output the wrong condition.

For this source file:

#include <linux/build_bug.h>

#define macro() \
BUILD_BUG_ON(1); \
BUILD_BUG_ON(0);

void foo()
{
macro();
}

gcc would output:

./include/linux/compiler.h:350:38: error: call to `__compiletime_assert_9' declared with attribute error: BUILD_BUG_ON failed: 0
  _compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)

However, it was not the BUILD_BUG_ON(0) that failed, so it should say 1
instead of 0. With this patch, we use __COUNTER__ instead of __LINE__, so
each BUILD_BUG_ON() gets a different function name and the correct
condition is printed:

./include/linux/compiler.h:350:38: error: call to `__compiletime_assert_0' declared with attribute error: BUILD_BUG_ON failed: 1
  _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)

Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Daniel Santos <daniel.santos@pobox.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200331112637.25047-1-vegard.nossum@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

percpu_counter: fix a data race at vm_committed_as

[ Upstream commit 7e2345200262e4a6056580f0231cccdaffc825f3 ]

"vm_committed_as.count" could be accessed concurrently as reported by
KCSAN,

 BUG: KCSAN: data-race in __vm_enough_memory / percpu_counter_add_batch

 write to 0xffffffff9451c538 of 8 bytes by task 65879 on cpu 35:
  percpu_counter_add_batch+0x83/0xd0
  percpu_counter_add_batch at lib/percpu_counter.c:91
  __vm_enough_memory+0xb9/0x260
  dup_mm+0x3a4/0x8f0
  copy_process+0x2458/0x3240
  _do_fork+0xaa/0x9f0
  __do_sys_clone+0x125/0x160
  __x64_sys_clone+0x70/0x90
  do_syscall_64+0x91/0xb05
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

 read to 0xffffffff9451c538 of 8 bytes by task 66773 on cpu 19:
  __vm_enough_memory+0x199/0x260
  percpu_counter_read_positive at include/linux/percpu_counter.h:81
  (inlined by) __vm_enough_memory at mm/util.c:839
  mmap_region+0x1b2/0xa10
  do_mmap+0x45c/0x700
  vm_mmap_pgoff+0xc0/0x130
  ksys_mmap_pgoff+0x6e/0x300
  __x64_sys_mmap+0x33/0x40
  do_syscall_64+0x91/0xb05
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

The read is outside percpu_counter::lock critical section which results in
a data race.  Fix it by adding a READ_ONCE() in
percpu_counter_read_positive() which could also service as the existing
compiler memory barrier.

Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Marco Elver <elver@google.com>
Link: http://lkml.kernel.org/r/1582302724-2804-1-git-send-email-cai@lca.pw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

include/linux/swapops.h: correct guards for non_swap_entry()

[ Upstream commit 3f3673d7d324d872d9d8ddb73b3e5e47fbf12e0d ]

If CONFIG_DEVICE_PRIVATE is defined, but neither CONFIG_MEMORY_FAILURE nor
CONFIG_MIGRATION, then non_swap_entry() will return 0, meaning that the
condition (non_swap_entry(entry) && is_device_private_entry(entry)) in
zap_pte_range() will never be true even if the entry is a device private
one.

Equally any other code depending on non_swap_entry() will not function as
expected.

I originally spotted this just by looking at the code, I haven't actually
observed any problems.

Looking a bit more closely it appears that actually this situation
(currently at least) cannot occur:

DEVICE_PRIVATE depends on ZONE_DEVICE
ZONE_DEVICE depends on MEMORY_HOTREMOVE
MEMORY_HOTREMOVE depends on MIGRATION

Fixes: 5042db43cc26 ("mm/ZONE_DEVICE: new type of ZONE_DEVICE for unaddressable memory")
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Link: http://lkml.kernel.org/r/20200305130550.22693-1-steven.price@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: do not commit super on read-only bdev

[ Upstream commit c96e2b8564adfb8ac14469ebc51ddc1bfecb3ae2 ]

Under some circumstances we may encounter a filesystem error on a
read-only block device, and if we try to save the error info to the
superblock and commit it, we'll wind up with a noisy error and
backtrace, i.e.:

[ 3337.146838] EXT4-fs error (device pmem1p2): ext4_get_journal_inode:4634: comm mount: inode #0: comm mount: iget: illegal inode #
------------[ cut here ]------------
generic_make_request: Trying to write to read-only block-device pmem1p2 (partno 2)
WARNING: CPU: 107 PID: 115347 at block/blk-core.c:788 generic_make_request_checks+0x6b4/0x7d0
...

To avoid this, commit the error info in the superblock only if the
block device is writable.

Reported-by: Ritesh Harjani <riteshh@linux.ibm.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Link: https://lore.kernel.org/r/4b6e774d-cc00-3469-7abb-108eb151071a@sandeen.net
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/maple: Fix declaration made after definition

[ Upstream commit af6cf95c4d003fccd6c2ecc99a598fb854b537e7 ]

When building ppc64 defconfig, Clang errors (trimmed for brevity):

  arch/powerpc/platforms/maple/setup.c:365:1: error: attribute declaration
  must precede definition [-Werror,-Wignored-attributes]
  machine_device_initcall(maple, maple_cpc925_edac_setup);
  ^

machine_device_initcall expands to __define_machine_initcall, which in
turn has the macro machine_is used in it, which declares mach_##name
with an __attribute__((weak)). define_machine actually defines
mach_##name, which in this file happens before the declaration, hence
the warning.

To fix this, move define_machine after machine_device_initcall so that
the declaration occurs before the definition, which matches how
machine_device_initcall and define_machine work throughout
arch/powerpc.

While we're here, remove some spaces before tabs.

Fixes: 8f101a051ef0 ("edac: cpc925 MC platform device setup")
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200323222729.15365-1-natechancellor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/cpuinfo: fix wrong output when CPU0 is offline

[ Upstream commit 872f27103874a73783aeff2aac2b41a489f67d7c ]

/proc/cpuinfo should not print information about CPU 0 when it is offline.

Fixes: 281eaa8cb67c ("s390/cpuinfo: simplify locking and skip offline cpus early")
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[heiko.carstens@de.ibm.com: shortened commit message]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFS: direct.c: Fix memory leak of dreq when nfs_get_lock_context fails

[ Upstream commit 8605cf0e852af3b2c771c18417499dc4ceed03d5 ]

When dreq is allocated by nfs_direct_req_alloc(), dreq->kref is
initialized to 2. Therefore we need to call nfs_direct_req_release()
twice to release the allocated dreq. Usually it is called in
nfs_file_direct_{read, write}() and nfs_direct_complete().

However, current code only calls nfs_direct_req_relese() once if
nfs_get_lock_context() fails in nfs_file_direct_{read, write}().
So, that case would result in memory leak.

Fix this by adding the missing call.

Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFSv4/pnfs: Return valid stateids in nfs_layout_find_inode_by_stateid()

[ Upstream commit d911c57a19551c6bef116a3b55c6b089901aacb0 ]

Make sure to test the stateid for validity so that we catch instances
where the server may have been reusing stateids in
nfs_layout_find_inode_by_stateid().

Fixes: 7b410d9ce460 ("pNFS: Delay getting the layout header in CB_LAYOUTRECALL handlers")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: 88pm860x: fix possible race condition

[ Upstream commit 9cf4789e6e4673d0b2c96fa6bb0c35e81b43111a ]

The RTC IRQ is requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.

To fix this issue, allocating the rtc_device struct before requesting
the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.

Also remove the unnecessary error message as the core already prints the
info.

Link: https://lore.kernel.org/r/20200311223956.51352-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc: imx: gpc: fix power up sequencing

[ Upstream commit e0ea2d11f8a08ba7066ff897e16c5217215d1e68 ]

Currently we wait only until the PGC inverts the isolation setting
before disabling the peripheral clocks. This doesn't ensure that the
reset is properly propagated through the peripheral devices in the
power domain.

Wait until the PGC signals that the power up request is done and
wait a bit for resets to propagate before disabling the clocks.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: tegra: Fix Tegra PMC clock out parents

[ Upstream commit 6fe38aa8cac3a5db38154331742835a4d9740788 ]

Tegra PMC clocks clk_out_1, clk_out_2, and clk_out_3 supported parents
are osc, osc_div2, osc_div4 and extern clock.

Clock driver is using incorrect parents clk_m, clk_m_div2, clk_m_div4
for PMC clocks.

This patch fixes this.

Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: bq27xxx_battery: Silence deferred-probe error

[ Upstream commit 583b53ece0b0268c542a1eafadb62e3d4b0aab8c ]

The driver fails to probe with -EPROBE_DEFER if battery's power supply
(charger driver) isn't ready yet and this results in a bit noisy error
message in KMSG during kernel's boot up. Let's silence the harmless
error message.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: at91: usb: continue if clk_hw_round_rate() return zero

[ Upstream commit b0ecf1c6c6e82da4847900fad0272abfd014666d ]

clk_hw_round_rate() may call round rate function of its parents. In case
of SAM9X60 two of USB parrents are PLLA and UPLL. These clocks are
controlled by clk-sam9x60-pll.c driver. The round rate function for this
driver is sam9x60_pll_round_rate() which call in turn
sam9x60_pll_get_best_div_mul(). In case the requested rate is not in the
proper range (rate < characteristics->output[0].min &&
rate > characteristics->output[0].max) the sam9x60_pll_round_rate() will
return a negative number to its caller (called by
clk_core_round_rate_nolock()). clk_hw_round_rate() will return zero in
case a negative number is returned by clk_core_round_rate_nolock(). With
this, the USB clock will continue its rate computation even caller of
clk_hw_round_rate() returned an error. With this, the USB clock on SAM9X60
may not chose the best parent. I detected this after a suspend/resume
cycle on SAM9X60.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lkml.kernel.org/r/1579261009-4573-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of: unittest: kmemleak in of_unittest_platform_populate()

[ Upstream commit 216830d2413cc61be3f76bc02ffd905e47d2439e ]

kmemleak reports several memory leaks from devicetree unittest.
This is the fix for problem 2 of 5.

of_unittest_platform_populate() left an elevated reference count for
grandchild nodes (which are platform devices).  Fix the platform
device reference counts so that the memory will be freed.

Fixes: fb2caa50fbac ("of/selftest: add testcase for nodes with same name and address")
Reported-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rbd: call rbd_dev_unprobe() after unwatching and flushing notifies

[ Upstream commit 952c48b0ed18919bff7528501e9a3fff8a24f8cd ]

rbd_dev_unprobe() is supposed to undo most of rbd_dev_image_probe(),
including rbd_dev_header_info(), which means that rbd_dev_header_info()
isn't supposed to be called after rbd_dev_unprobe().

However, rbd_dev_image_release() calls rbd_dev_unprobe() before
rbd_unregister_watch().  This is racy because a header update notify
can sneak in:

  "rbd unmap" thread                   ceph-watch-notify worker

  rbd_dev_image_release()
    rbd_dev_unprobe()
      free and zero out header
                                       rbd_watch_cb()
                                         rbd_dev_refresh()
                                           rbd_dev_header_info()
                                             read in header

The same goes for "rbd map" because rbd_dev_image_probe() calls
rbd_dev_unprobe() on errors.  In both cases this results in a memory
leak.

Fixes: fd22aef8b47c ("rbd: move rbd_unregister_watch() call into rbd_dev_image_release()")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rbd: avoid a deadlock on header_rwsem when flushing notifies

[ Upstream commit 0e4e1de5b63fa423b13593337a27fd2d2b0bcf77 ]

rbd_unregister_watch() flushes notifies and therefore cannot be called
under header_rwsem because a header update notify takes header_rwsem to
synchronize with "rbd map".  If mapping an image fails after the watch
is established and a header update notify sneaks in, we deadlock when
erroring out from rbd_dev_image_probe().

Move watch registration and unregistration out of the critical section.
The only reason they were put there was to make header_rwsem management
slightly more obvious.

Fixes: 811c66887746 ("rbd: fix rbd map vs notify races")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of: fix missing kobject init for !SYSFS && OF_DYNAMIC config

[ Upstream commit bd82bbf38cbe27f2c65660da801900d71bcc5cc8 ]

The ref counting is broken for OF_DYNAMIC when sysfs is disabled because
the kobject initialization is skipped. Only the properties
add/remove/update should be skipped for !SYSFS config.

Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

soc: qcom: smem: Use le32_to_cpu for comparison

[ Upstream commit a216000f0140f415cec96129f777b5234c9d142f ]

Endianness can vary in the system, add le32_to_cpu when comparing
partition sizes from smem.

Signed-off-by: Chris Lew <clew@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wil6210: abort properly in cfg suspend

[ Upstream commit 144a12a6d83f3ca34ddefce5dee4d502afd2fc5b ]

On-going operations were not aborted properly
and required locks were not taken.

Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wil6210: fix length check in __wmi_send

[ Upstream commit 26a6d5274865532502c682ff378ac8ebe2886238 ]

The current length check:
sizeof(cmd) + len > r->entry_size
will allow very large values of len (> U16_MAX - sizeof(cmd))
and can cause a buffer overflow. Fix the check to cover this case.
In addition, ensure the mailbox entry_size is not too small,
since this can also bypass the above check.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wil6210: add block size checks during FW load

[ Upstream commit 705d2fde94b23cd76efbeedde643ffa7c32fac7f ]

When loading FW from file add block size checks to ensure a
corrupted FW file will not cause the driver to write outside
the device memory.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wil6210: fix PCIe bus mastering in case of interface down

[ Upstream commit 680c242dc25e036265793edc7d755cfc15afd231 ]

In case of interface down, radio is turned off but PCIe mastering is
not cleared.
This can cause unexpected PCIe access to the shutdown device.
Fix this by clearing PCIe mastering also in case interface is down

Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: smem: Ensure ordering during tx

[ Upstream commit 9d32497361ff89d2fc8306407de6f04b2bfb2836 ]

Ensure the ordering of the fifo write and the update of the write index,
so that the index is not updated before the data has landed in the fifo.

Acked-By: Chris Lew <clew@codeaurora.org>
Reported-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: Fix missing mutex_init() in qcom_glink_alloc_channel()

[ Upstream commit fb416f69900773d5a6030c909114099f92d07ab9 ]

qcom_glink_alloc_channel() allocates the mutex but not initialize it.
Use mutex_init() on it to initialize it correctly.

This is detected by Coccinelle semantic patch.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: pm8xxx: Fix issue in RTC write path

[ Upstream commit 83220bf38b77a830f8e62ab1a0d0408304f9b966 ]

In order to set time in rtc, need to disable
rtc hw before writing into rtc registers.

Also fixes disabling of alarm while setting
rtc time.

Signed-off-by: Mohit Aggarwal <maggarwa@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: glink: use put_device() if device_register fail

[ Upstream commit a9011726c4bb37e5d6a7279bf47fcc19cd9d3e1a ]

if device_register() returned an error! Always use put_device()
to give up the reference initialized. And unregister device for
other return error.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wil6210: rate limit wil_rx_refill error

[ Upstream commit 3d6b72729cc2933906de8d2c602ae05e920b2122 ]

wil_err inside wil_rx_refill can flood the log buffer.
Replace it with wil_err_ratelimited.

Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: ufs-qcom: remove broken hci version quirk

[ Upstream commit 69a6fff068567469c0ef1156ae5ac8d3d71701f0 ]

UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION is only applicable for QCOM UFS host
controller version 2.x.y and this has been fixed from version 3.x.y
onwards, hence this change removes this quirk for version 3.x.y onwards.

[mkp: applied by hand]

Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: make sure all interrupts are processed

[ Upstream commit 7f6ba4f12e6cbfdefbb95cfd8fc67ece6c15d799 ]

As multiple requests are submitted to the ufs host controller in
parallel there could be instances where the command completion interrupt
arrives later for a request that is already processed earlier as the
corresponding doorbell was cleared when handling the previous
interrupt. Read the interrupt status in a loop after processing the
received interrupt to catch such interrupts and handle it.

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wil6210: fix temperature debugfs

[ Upstream commit 6d9eb7ebae3d7e951bc0999235ae7028eb4cae4f ]

For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.

Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wil6210: increase firmware ready timeout

[ Upstream commit 6ccae584014ef7074359eb4151086beef66ecfa9 ]

Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.

Increase the timeout to support these scenarios.

Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arch_topology: Fix section miss match warning due to free_raw_capacity()

[ Upstream commit 82d8ba717ccb54dd803624db044f351b2a54d000 ]

Remove the __init annotation from free_raw_capacity() to avoid
the following warning.

The function init_cpu_capacity_callback() references the
function __init free_raw_capacity().
WARNING: vmlinux.o(.text+0x425cc0): Section mismatch in reference
from the function init_cpu_capacity_callback() to the function
.init.text:free_raw_capacity().

Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: traps: Don't print stack or raw PC/LR values in backtraces

[ Upstream commit a25ffd3a6302a67814280274d8f1aa4ae2ea4b59 ]

Printing raw pointer values in backtraces has potential security
implications and are of questionable value anyway.

This patch follows x86's lead and removes the "Exception stack:" dump
from kernel backtraces, as well as converting PC/LR values to symbols
such as "sysrq_handle_crash+0x20/0x30".

Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: perf: remove unsupported events for Cortex-A73

[ Upstream commit f8ada189550984ee21f27be736042b74a7da1d68 ]

bus access read/write events are not supported in A73, based on the
Cortex-A73 TRM r0p2, section 11.9 Events (pages 11-457 to 11-460).

Fixes: 5561b6c5e981 "arm64: perf: add support for Cortex-A73"
Acked-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Xu YiPing <xuyiping@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "gpio: set up initial state from .get_direction()"

[ Upstream commit 1ca2a92b2a99323f666f1b669b7484df4bda05e4 ]

This reverts commit 72d3200061776264941be1b5a9bb8e926b3b30a5.

We cannot blindly query the direction of all GPIOs when the pins are
first registered.  The get_direction callback normally triggers a
read/write to hardware, but we shouldn't be touching the hardware for
an individual GPIO until after it's been properly claimed.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: Fix debugfs_create_*() usage

commit 4c8326d5ebb0de3191e98980c80ab644026728d0 upstream.

When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, matching the data
types.

Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.

clk_core.rate and .accuracy are "unsigned long", hence casting
their addresses to "u32 *" exposed the wrong halves on big-endian
64-bit systems. Fix this by using debugfs_create_ulong() instead.

Octal permissions are preferred, as they are easier to read than
symbolic permissions. Hence replace "S_IRUGO" by "0444"
throughout.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[sboyd@codeaurora.org: Squash the octal change in too]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: NULL pointer dereference [null-pointer-deref] (CWE 476) problem

commit 22a07038c0eaf4d1315a493ce66dcd255accba19 upstream.

The Parfait (version 2.1.0) static code analysis tool found the
following NULL pointer derefernce problem.

- drivers/gpu/drm/drm_dp_mst_topology.c
The call to drm_dp_calculate_rad() in function drm_dp_port_setup_pdt()
could result in a NULL pointer being returned to port->mstb due to a
failure to allocate memory for port->mstb.

Signed-off-by: Joe Moriarty <joe.moriarty@oracle.com>
Reviewed-by: Steven Sistare <steven.sistare@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180212195144.98323-3-joe.moriarty@oracle.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

video: fbdev: sis: Remove unnecessary parentheses and commented code

commit 864eb1afc60cb43e7df879b97f8ca0d719bbb735 upstream.

Clang warns when multiple pairs of parentheses are used for a single
conditional statement.

drivers/video/fbdev/sis/init301.c:851:42: warning: equality comparison
with extraneous parentheses [-Wparentheses-equality]
      } else if((SiS_Pr->SiS_IF_DEF_LVDS == 1) /* ||
                 ~~~~~~~~~~~~~~~~~~~~~~~~^~~~
drivers/video/fbdev/sis/init301.c:851:42: note: remove extraneous
parentheses around the comparison to silence this warning
      } else if((SiS_Pr->SiS_IF_DEF_LVDS == 1) /* ||
                ~                        ^   ~
drivers/video/fbdev/sis/init301.c:851:42: note: use '=' to turn this
equality comparison into an assignment
      } else if((SiS_Pr->SiS_IF_DEF_LVDS == 1) /* ||
                                         ^~
                                         =
1 warning generated.

Remove the parentheses and while we're at it, clean up the commented
code, which has been here since the beginning of git history.

Link: https://github.com/ClangBuiltLinux/linux/issues/118
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/raid6: use vdupq_n_u8 to avoid endianness warnings

commit 1ad3935b39da78a403e7df7a3813f866c731bc64 upstream.

Clang warns: vector initializers are not compatible with NEON intrinsics
in big endian mode [-Wnonportable-vector-initialization]

While this is usually the case, it's not an issue for this case since
we're initializing the uint8x16_t (16x uint8_t's) with the same value.

Instead, use vdupq_n_u8 which both compilers lower into a single movi
instruction: https://godbolt.org/z/vBrgzt

This avoids the static storage for a constant value.

Link: https://github.com/ClangBuiltLinux/linux/issues/214
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Don't release card at firmware loading error

commit 25faa4bd37c10f19e4b848b9032a17a3d44c6f09 upstream.

At the error path of the firmware loading error, the driver tries to
release the card object and set NULL to drvdata.  This may be referred
badly at the possible PM action, as the driver itself is still bound
and the PM callbacks read the card object.

Instead, we continue the probing as if it were no option set.  This is
often a better choice than the forced abort, too.

Fixes: 5cb543dba986 ("ALSA: hda - Deferred probing with request_firmware_nowait()")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207043
Link: https://lore.kernel.org/r/20200413082034.25166-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/mbigen: Free msi_desc on device teardown

commit edfc23f6f9fdbd7825d50ac1f380243cde19b679 upstream.

Using irq_domain_free_irqs_common() on the irqdomain free path will
leave the MSI descriptor unfreed when platform devices get removed.
Properly free it by MSI domain free function.

Fixes: 9650c60ebfec0 ("irqchip/mbigen: Create irq domain for each mbigen device")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200408114352.1604-1-yuzenghui@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>