Drivers: hv: vmbus: Fix ring buffer signaling

commit 655296c8bbeffcf020558c4455305d597a73bde1 upstream.

Fix bugs in signaling the Hyper-V host when freeing space in the
host->guest ring buffer:

1. The interrupt_mask must not be used to determine whether to signal
   on the host->guest ring buffer
2. The ring buffer write_index must be read (via hv_get_bytes_to_write)
   *after* pending_send_sz is read in order to avoid a race condition
3. Comparisons with pending_send_sz must treat the "equals" case as
   not-enough-space
4. Don't signal if the pending_send_sz feature is not present. Older
   versions of Hyper-V that don't implement this feature will poll.

Fixes: 03bad714a161 ("vmbus: more host signalling avoidance")

Cc: Stable <stable@vger.kernel.org> # 4.14 and above
Signed-off-by: Michael Kelley <mhkelley@outlook.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/mlx5: Fix crash while accessing garbage pointer and freed memory

commit f3f134f5260ae9ee1f5a4d0a8cc625c6c77655b4 upstream.

The failure in rereg_mr flow caused to set garbage value (error value)
into mr->umem pointer. This pointer is accessed at the release stage
and it causes to the following crash.

There is not enough to simply change umem to point to NULL, because the
MR struct is needed to be accessed during MR deregistration phase, so
delay kfree too.

[    6.237617] BUG: unable to handle kernel NULL pointer dereference a 0000000000000228
[    6.238756] IP: ib_dereg_mr+0xd/0x30
[    6.239264] PGD 80000000167eb067 P4D 80000000167eb067 PUD 167f9067 PMD 0
[    6.240320] Oops: 0000 [#1] SMP PTI
[    6.240782] CPU: 0 PID: 367 Comm: dereg Not tainted 4.16.0-rc1-00029-gc198fafe0453 #183
[    6.242120] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
[    6.244504] RIP: 0010:ib_dereg_mr+0xd/0x30
[    6.245253] RSP: 0018:ffffaf5d001d7d68 EFLAGS: 00010246
[    6.246100] RAX: 0000000000000000 RBX: ffff95d4172daf00 RCX: 0000000000000000
[    6.247414] RDX: 00000000ffffffff RSI: 0000000000000001 RDI: ffff95d41a317600
[    6.248591] RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
[    6.249810] R10: ffff95d417033c10 R11: 0000000000000000 R12: ffff95d4172c3a80
[    6.251121] R13: ffff95d4172c3720 R14: ffff95d4172c3a98 R15: 00000000ffffffff
[    6.252437] FS:  0000000000000000(0000) GS:ffff95d41fc00000(0000) knlGS:0000000000000000
[    6.253887] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    6.254814] CR2: 0000000000000228 CR3: 00000000172b4000 CR4: 00000000000006b0
[    6.255943] Call Trace:
[    6.256368]  remove_commit_idr_uobject+0x1b/0x80
[    6.257118]  uverbs_cleanup_ucontext+0xe4/0x190
[    6.257855]  ib_uverbs_cleanup_ucontext.constprop.14+0x19/0x40
[    6.258857]  ib_uverbs_close+0x2a/0x100
[    6.259494]  __fput+0xca/0x1c0
[    6.259938]  task_work_run+0x84/0xa0
[    6.260519]  do_exit+0x312/0xb40
[    6.261023]  ? __do_page_fault+0x24d/0x490
[    6.261707]  do_group_exit+0x3a/0xa0
[    6.262267]  SyS_exit_group+0x10/0x10
[    6.262802]  do_syscall_64+0x75/0x180
[    6.263391]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[    6.264253] RIP: 0033:0x7f1b39c49488
[    6.264827] RSP: 002b:00007ffe2de05b68 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
[    6.266049] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1b39c49488
[    6.267187] RDX: 0000000000000000 RSI: 000000000000003c RDI: 0000000000000000
[    6.268377] RBP: 00007f1b39f258e0 R08: 00000000000000e7 R09: ffffffffffffff98
[    6.269640] R10: 00007f1b3a147260 R11: 0000000000000246 R12: 00007f1b39f258e0
[    6.270783] R13: 00007f1b39f2ac20 R14: 0000000000000000 R15: 0000000000000000
[    6.271943] Code: 74 07 31 d2 e9 25 d8 6c 00 b8 da ff ff ff c3 0f 1f
44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 07 53 48 8b
5f 08 <48> 8b 80 28 02 00 00 e8 f7 d7 6c 00 85 c0 75 04 3e ff 4b 18 5b
[    6.274927] RIP: ib_dereg_mr+0xd/0x30 RSP: ffffaf5d001d7d68
[    6.275760] CR2: 0000000000000228
[    6.276200] ---[ end trace a35641f1c474bd20 ]---

Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Cc: syzkaller <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org>
Reported-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: sunxi-ng: a31: Fix CLK_OUT_* clock ops

commit 5682e268350f9eccdbb04006605c1b7068a7b323 upstream.

When support for the A31/A31s CCU was first added, the clock ops for
the CLK_OUT_* clocks was set to the wrong type. The clocks are MP-type,
but the ops was set for div (M) clocks. This went unnoticed until now.
This was because while they are different clocks, their data structures
aligned in a way that ccu_div_ops would access the second ccu_div_internal
and ccu_mux_internal structures, which were valid, if not incorrect.

Furthermore, the use of these CLK_OUT_* was for feeding a precise 32.768
kHz clock signal to the WiFi chip. This was achievable by using the parent
with the same clock rate and no divider. So the incorrect divider setting
did not affect this usage.

Commit 946797aa3f08 ("clk: sunxi-ng: Support fixed post-dividers on MP
style clocks") added a new field to the ccu_mp structure, which broke
the aforementioned alignment. Now the system crashes as div_ops tries
to look up a nonexistent table.

Reported-by: Philipp Rossak <embed3d@gmail.com>
Tested-by: Philipp Rossak <embed3d@gmail.com>
Fixes: c6e6c96d8fa6 ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: bcm2835: Protect sections updating shared registers

commit 7997f3b2df751aab0b8e60149b226a32966c41ac upstream.

CM_PLLx and A2W_XOSC_CTRL registers are accessed by different clock
handlers and must be accessed with ->regs_lock held.
Update the sections where this protection is missing.

Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: bcm2835: Fix ana->maskX definitions

commit 49012d1bf5f78782d398adb984a080a88ba42965 upstream.

ana->maskX values are already '~'-ed in bcm2835_pll_set_rate(). Remove
the '~' in the definition to fix ANA setup.

Note that this commit fixes a long standing bug preventing one from
using an HDMI display if it's plugged after the FW has booted Linux.
This is because PLLH is used by the HDMI encoder to generate the pixel
clock.

Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lockdep: fix fs_reclaim warning

commit 2e517d681632326ed98399cb4dd99519efe3e32c upstream.

Dave Jones reported fs_reclaim lockdep warnings.

  ============================================
  WARNING: possible recursive locking detected
  4.15.0-rc9-backup-debug+ #1 Not tainted
  --------------------------------------------
  sshd/24800 is trying to acquire lock:
   (fs_reclaim){+.+.}, at: [<0000000084f438c2>] fs_reclaim_acquire.part.102+0x5/0x30

  but task is already holding lock:
   (fs_reclaim){+.+.}, at: [<0000000084f438c2>] fs_reclaim_acquire.part.102+0x5/0x30

  other info that might help us debug this:
   Possible unsafe locking scenario:

         CPU0
         ----
    lock(fs_reclaim);
    lock(fs_reclaim);

   *** DEADLOCK ***

   May be due to missing lock nesting notation

  2 locks held by sshd/24800:
   #0:  (sk_lock-AF_INET6){+.+.}, at: [<000000001a069652>] tcp_sendmsg+0x19/0x40
   #1:  (fs_reclaim){+.+.}, at: [<0000000084f438c2>] fs_reclaim_acquire.part.102+0x5/0x30

  stack backtrace:
  CPU: 3 PID: 24800 Comm: sshd Not tainted 4.15.0-rc9-backup-debug+ #1
  Call Trace:
   dump_stack+0xbc/0x13f
   __lock_acquire+0xa09/0x2040
   lock_acquire+0x12e/0x350
   fs_reclaim_acquire.part.102+0x29/0x30
   kmem_cache_alloc+0x3d/0x2c0
   alloc_extent_state+0xa7/0x410
   __clear_extent_bit+0x3ea/0x570
   try_release_extent_mapping+0x21a/0x260
   __btrfs_releasepage+0xb0/0x1c0
   btrfs_releasepage+0x161/0x170
   try_to_release_page+0x162/0x1c0
   shrink_page_list+0x1d5a/0x2fb0
   shrink_inactive_list+0x451/0x940
   shrink_node_memcg.constprop.88+0x4c9/0x5e0
   shrink_node+0x12d/0x260
   try_to_free_pages+0x418/0xaf0
   __alloc_pages_slowpath+0x976/0x1790
   __alloc_pages_nodemask+0x52c/0x5c0
   new_slab+0x374/0x3f0
   ___slab_alloc.constprop.81+0x47e/0x5a0
   __slab_alloc.constprop.80+0x32/0x60
   __kmalloc_track_caller+0x267/0x310
   __kmalloc_reserve.isra.40+0x29/0x80
   __alloc_skb+0xee/0x390
   sk_stream_alloc_skb+0xb8/0x340
   tcp_sendmsg_locked+0x8e6/0x1d30
   tcp_sendmsg+0x27/0x40
   inet_sendmsg+0xd0/0x310
   sock_write_iter+0x17a/0x240
   __vfs_write+0x2ab/0x380
   vfs_write+0xfb/0x260
   SyS_write+0xb6/0x140
   do_syscall_64+0x1e5/0xc05
   entry_SYSCALL64_slow_path+0x25/0x25

This warning is caused by commit d92a8cfcb37e ("locking/lockdep:
Rework FS_RECLAIM annotation") which replaced the use of
lockdep_{set,clear}_current_reclaim_state() in __perform_reclaim()
and lockdep_trace_alloc() in slab_pre_alloc_hook() with
fs_reclaim_acquire()/ fs_reclaim_release().

Since __kmalloc_reserve() from __alloc_skb() adds __GFP_NOMEMALLOC |
__GFP_NOWARN to gfp_mask, and all reclaim path simply propagates
__GFP_NOMEMALLOC, fs_reclaim_acquire() in slab_pre_alloc_hook() is
trying to grab the 'fake' lock again when __perform_reclaim() already
grabbed the 'fake' lock.

The

  /* this guy won't enter reclaim */
  if ((current->flags & PF_MEMALLOC) && !(gfp_mask & __GFP_NOMEMALLOC))
          return false;

test which causes slab_pre_alloc_hook() to try to grab the 'fake' lock
was added by commit cf40bd16fdad ("lockdep: annotate reclaim context
(__GFP_NOFS)").  But that test is outdated because PF_MEMALLOC thread
won't enter reclaim regardless of __GFP_NOMEMALLOC after commit
341ce06f69ab ("page allocator: calculate the alloc_flags for allocation
only once") added the PF_MEMALLOC safeguard (

  /* Avoid recursion of direct reclaim */
  if (p->flags & PF_MEMALLOC)
          goto nopage;

in __alloc_pages_slowpath()).

Thus, let's fix outdated test by removing __GFP_NOMEMALLOC test and
allow __need_fs_reclaim() to return false.

Link: http://lkml.kernel.org/r/201802280650.FJC73911.FOSOMLJVFFQtHO@I-love.SAKURA.ne.jp
Fixes: d92a8cfcb37ecd13 ("locking/lockdep: Rework FS_RECLAIM annotation")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Tested-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nikolay Borisov <nborisov@suse.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ahci: Add PCI-id for the Highpoint Rocketraid 644L card

commit 28b2182dad43f6f8fcbd167539a26714fd12bd64 upstream.

Like the Highpoint Rocketraid 642L and cards using a Marvel 88SE9235
controller in general, this RAID card also supports AHCI mode and short
of a custom driver, this is the only way to make it work under Linux.

Note that even though the card is called to 644L, it has a product-id
of 0x0645.

Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L

commit 1903be8222b7c278ca897c129ce477c1dd6403a8 upstream.

The Highpoint RocketRAID 644L uses a Marvel 88SE9235 controller, as with
other Marvel controllers this needs a function 1 DMA alias quirk.

Note the RocketRAID 642L uses the same Marvel 88SE9235 controller and
already is listed with a function 1 DMA alias quirk.

Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occurs

commit 47b7de2f6c18f75d1f2716efe752cba43f32a626 upstream.

It was found that in IDMAC mode after soft-reset driver switches
to PIO mode.

That's what happens in case of DTO timeout overflow calculation failure:
1. soft-reset is called
2. driver restarts dma
3. descriptors states are checked, one of descriptor is owned by the IDMAC.
4. driver can't use DMA and then switches to PIO mode.

Failure was already fixed in:
https://www.spinics.net/lists/linux-mmc/msg48125.html.

Behaviour while soft-reset is not something we except or
even want to happen. So we switch from dw_mci_idmac_reset
to dw_mci_idmac_init, so descriptors are cleaned before starting dma.

And while at it explicitly zero des0 which otherwise might
contain garbage as being allocated by dmam_alloc_coherent().

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: dw_mmc: exynos: fix the suspend/resume issue for exynos5433

commit e22842dd64bf86753d3f2b6ea474d73fc1e6ca24 upstream.

Before enabling the clock, dwmmc exynos driver is trying to access the
register. Then the kernel panic can be occurred.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: dw_mmc: Fix the DTO/CTO timeout overflow calculation for 32-bit systems

commit c7151602255a36ba07c84fe2baeef846fdb988b8 upstream.

The commit 9d9491a7da2a ("mmc: dw_mmc: Fix the DTO timeout calculation")
and commit 4c2357f57dd5 ("mmc: dw_mmc: Fix the CTO timeout calculation")
made changes, which cause multiply overflow for 32-bit systems. The broken
timeout calculations leads to unexpected ETIMEDOUT errors and causes
stacktrace splat (such as below) during normal data exchange with SD-card.

| Running :  4M-check-reassembly-tcp-cmykw2-rotatew2.out -v0 -w1
| -  Info: Finished target initialization.
| mmcblk0: error -110 transferring data, sector 320544, nr 2048, cmd
| response 0x900, card status 0x0

DIV_ROUND_UP_ULL helps to escape usage of __udivdi3() from libgcc and so
code gets compiled on all 32-bit platforms as opposed to usage of
DIV_ROUND_UP when we may only compile stuff on a very few arches.

Lets cast this multiply to u64 type to prevent the overflow.

Fixes: 9d9491a7da2a ("mmc: dw_mmc: Fix the DTO timeout calculation")
Fixes: 4c2357f57dd5 ("mmc: dw_mmc: Fix the CTO timeout calculation")
Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> # ARC STAR 9001306872 HSDK, sdio: board crashes when copying big files
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: <stable@vger.kernel.org> # 4.14
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: block: fix updating ext_csd caches on ioctl call

commit e74ef2194b41ba5e511fab29fe5ff00e72d2f42a upstream.

PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.

Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.

Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards

commit dbe7dc6b9b28f5b012b0bedc372aa0c52521f3e4 upstream.

Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.

In U-Boot, these cards are reported as

Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022  Manufact. date: 8/2015 (0x82)  CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit

According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: core: Fix tracepoint print of blk_addr and blksz

commit c658dc58c7eaa8569ceb0edd1ddbdfda84fe8aa5 upstream.

Swap the positions of blk_addr and blksz in the tracepoint print arguments
so that they match the print format.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: d2f82254e4e8 ("mmc: core: Add members to mmc_request and mmc_data for CQE's")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Always immediately update mute LED with pin VREF

commit e40bdb03d3cd7da66bd0bc1e40cbcfb49351265c upstream.

Some HP laptops have a mute mute LED controlled by a pin VREF.  The
Realtek codec driver updates the VREF via vmaster hook by calling
snd_hda_set_pin_ctl_cache().

This works fine as long as the driver is running in a normal mode.
However, when the VREF change happens during the codec being in
runtime PM suspend, the regmap access will skip and postpone the
actual register change.  This ends up with the unchanged LED status
until the next runtime PM resume even if you change the Master mute
switch.  (Interestingly, the machine keeps the LED status even after
the codec goes into D3 -- but it's another story.)

For improving this usability, let the driver temporarily powering up /
down only during the pin VREF change.  This can be achieved easily by
wrapping the call with snd_hda_power_up_pm() / *_down_pm().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199073
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Fix Dell headset Mic can't record

commit f0ba9d699e5ca2bcd07f70185d18720c4f1b597c upstream.

This platform was hardware fixed type for CTIA type for headset port.
Assigned 0x19 verb will fix can't record issue.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Fix speaker no sound after system resume

commit 88d42b2b45d7208cc872c2c9dec0b1ae6c6008d7 upstream.

It will have a chance speaker no sound after system resume.
To toggle NID 0x53 index 0x2 bit 15 will solve this issue.
This usage will also suitable with ALC256.

Fixes: 4a219ef8f370 ("ALSA: hda/realtek - Add ALC256 HP depop function")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Force polling mode on CFL for fixing codec communication

commit a8d7bde23e7130686b76624b099f3e22dd38aef7 upstream.

We've observed too long probe time with Coffee Lake (CFL) machines,
and the likely cause is some communication problem between the
HD-audio controller and the codec chips.  While the controller expects
an IRQ wakeup for each codec response, it seems sometimes missing, and
it takes one second for the controller driver to time out and read the
response in the polling mode.

Although we aren't sure about the real culprit yet, in this patch, we
put a workaround by forcing the polling mode as default for CFL
machines; the polling mode itself isn't too heavy, and much better
than other workarounds initially suggested (e.g. disabling
power-save), at least.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199007
Fixes: e79b0006c45c ("ALSA: hda - Add Coffelake PCI ID")
Reported-and-tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: aloop: Fix access to not-yet-ready substream via cable

commit 8e6b1a72a75bb5067ccb6b56d8ca4aa3a300a64e upstream.

In loopback_open() and loopback_close(), we assign and release the
substream object to the corresponding cable in a racy way.  It's
neither locked nor done in the right position.  The open callback
assigns the substream before its preparation finishes, hence the other
side of the cable may pick it up, which may lead to the invalid memory
access.

This patch addresses these: move the assignment to the end of the open
callback, and wrap with cable->lock for avoiding concurrent accesses.

Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: aloop: Sync stale timer before release

commit 67a01afaf3d34893cf7d2ea19b34555d6abb7cb0 upstream.

The aloop driver tries to stop the pending timer via timer_del() in
the trigger callback and in the close callback.  The former is
correct, as it's an atomic operation, while the latter expects that
the timer gets really removed and proceeds the resource releases after
that.  But timer_del() doesn't synchronize, hence the running timer
may still access the released resources.

A similar situation can be also seen in the prepare callback after
trigger(STOP) where the prepare tries to re-initialize the things
while a timer is still running.

The problems like the above are seen indirectly in some syzkaller
reports (although it's not 100% clear whether this is the only cause,
as the race condition is quite narrow and not always easy to
trigger).

For addressing these issues, this patch adds the explicit alls of
timer_del_sync() in some places, so that the pending timer is properly
killed / synced.

Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Fix parsing descriptor of UAC2 processing unit

commit a6618f4aedb2b60932d766bd82ae7ce866e842aa upstream.

Currently, the offsets in the UAC2 processing unit descriptor are
calculated incorrectly. It causes an issue when connecting the device which
provides such a feature:

~~~~
[84126.724420] usb 1-1.3.1: invalid Processing Unit descriptor (id 18)
~~~~

After this patch is applied, the UAC2 processing unit inits w/o this error.

Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: meson-saradc: unlock on error in meson_sar_adc_lock()

commit 3c3e4b3a708a9d6451052e348981f37d2b3e92b0 upstream.

The meson_sar_adc_lock() function is not supposed to hold the
"indio_dev->mlock" on the error path.

Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: st_pressure: st_accel: pass correct platform data to init

commit 8b438686a001db64c21782d04ef68111e53c45d9 upstream.

Commit 7383d44b added a pointer pdata which get set to the default
platform_data when non was defined in the device. But it did not
pass this pointer to the st_sensors_init_sensor call but still
used the maybe uninitialized platform_data from dev.

This breaks initialization when no platform_data is given and
the optional st,drdy-int-pin devicetree option is not set.

This commit fixes this.

Cc: stable@vger.kernel.org
Fixes: 7383d44b ("iio: st_pressure: st_accel: Initialise sensor platform data properly")
Signed-off-by: Michael Nosthoff <committed@heine.so>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: chemical: ccs811: Corrected firmware boot/application mode transition

commit b91e146c38b003c899710ede6d05fc824675e386 upstream.

CCS811 has different I2C register maps in boot and application mode. When
CCS811 is in boot mode, register APP_START (0xF4) is used to transit the
firmware state from boot to application mode. However, APP_START is not a
valid register location when CCS811 is in application mode (refer to
"CCS811 Bootloader Register Map" and "CCS811 Application Register Map" in
CCS811 datasheet). The driver should not attempt to perform a write to
APP_START while CCS811 is in application mode, as this is not a valid or
documented register location.

When prob function is being called, the driver assumes the CCS811 sensor
is in boot mode, and attempts to perform a write to APP_START. Although
CCS811 powers-up in boot mode, it may have already been transited to
application mode by previous instances, e.g. unload and reload device
driver by the system, or explicitly by user. Depending on the system
design, CCS811 sensor may be permanently connected to system power source
rather than power controlled by GPIO, hence it is possible that the sensor
is never power reset, thus the firmware could be in either boot or
application mode at any given time when driver prob function is being
called.

This patch checks the STATUS register before attempting to send a write to
APP_START. Only if the firmware is not in application mode and has valid
firmware application loaded, then it will continue to start transiting the
firmware boot to application mode.

Signed-off-by: Richard Lai <richard@richardman.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: lantiq: ase: Enable MFD_SYSCON

commit a821328c2f3003b908880792d71b2781b44fa53c upstream.

Enable syscon to use it for the RCU MFD on Amazon SE as well.

The Amazon SE also has similar reset controller system as Danube and
XWAY and use their drivers mostly. As these drivers now need syscon also
activate the syscon subsystem for for Amazon SE.

Fixes: 2b6639d4c794 ("MIPS: lantiq: Enable MFD_SYSCON to be able to use it for the RCU MFD")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.14+
Patchwork: https://patchwork.linux-mips.org/patch/18817/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: lantiq: Enable AHB Bus for USB

commit 3223a5a7d3a606dcb7d9190a788b9544a45441ee upstream.

On Danube and AR9 the USB core is connected though a AHB bus to the main
system cross bar, hence we need to enable the gating clock of the AHB
Bus as well to make the USB controller work.

Fixes: dea54fbad332 ("phy: Add an USB PHY driver for the Lantiq SoCs using the RCU module")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.14+
Patchwork: https://patchwork.linux-mips.org/patch/18814/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: lantiq: Fix Danube USB clock

commit 214cbc14734958fe533916fdb4194f5983ad4bc4 upstream.

On Danube the USB0 controller registers are at 1e101000 and the USB0 PHY
register is at 1f203018 similar to all other lantiq SoCs. Activate the
USB controller gating clock thorough the USB controller driver and not
the PHY.

This fixes a problem introduced in a previous commit.

Fixes: dea54fbad332 ("phy: Add an USB PHY driver for the Lantiq SoCs using the RCU module")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.14+
Patchwork: https://patchwork.linux-mips.org/patch/18816/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ralink: Fix booting on MT7621

commit a63d706ea719190a79a6c769e898f70680044d3e upstream.

Since commit 3af5a67c86a3 ("MIPS: Fix early CM probing") the MT7621 has
not been able to boot.

This commit caused mips_cm_probe() to be called before
mt7621.c::proc_soc_init().

prom_soc_init() has a comment explaining that mips_cm_probe() "wipes out
the bootloader config" and means that configuration registers are no
longer available. It has some code to re-enable this config.

Before this re-enable code is run, the sysc register cannot be read, so
when SYSC_REG_CHIP_NAME0 is read, a garbage value is returned and
panic() is called.

If we move the config-repair code to the top of prom_soc_init(), the
registers can be read and boot can proceed.

Very occasionally, the first register read after the reconfiguration
returns garbage, so add a call to __sync().

Fixes: 3af5a67c86a3 ("MIPS: Fix early CM probing")
Signed-off-by: NeilBrown <neil@brown.name>
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.5+
Patchwork: https://patchwork.linux-mips.org/patch/18859/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ralink: Remove ralink_halt()

commit 891731f6a5dbe508d12443175a7e166a2fba616a upstream.

ralink_halt() does nothing that machine_halt() doesn't already do, so it
adds no value.

It actually causes incorrect behaviour due to the "unreachable()" at the
end. This tells the compiler that the end of the function will never be
reached, which isn't true. The compiler responds by not adding a
'return' instruction, so control simply moves on to whatever bytes come
afterwards in memory. In my tested, that was the ralink_restart()
function. This means that an attempt to 'halt' the machine would
actually cause a reboot.

So remove ralink_halt() so that a 'halt' really does halt.

Fixes: c06e836ada59 ("MIPS: ralink: adds reset code")
Signed-off-by: NeilBrown <neil@brown.name>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.9+
Patchwork: https://patchwork.linux-mips.org/patch/18851/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.30

RDMA/vmw_pvrdma: Fix usage of user response structures in ABI file

commit 1f5a6c47aabc4606f91ad2e6ef71a1ff1924101c upstream.

This ensures that we return the right structures back to userspace.
Otherwise, it looks like the reserved fields in the response structures
in userspace might have uninitialized data in them.

Fixes: 8b10ba783c9d ("RDMA/vmw_pvrdma: Add shared receive queue support")
Fixes: 29c8d9eba550 ("IB: Add vmw_pvrdma driver")
Suggested-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Bryan Tan <bryantan@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: fix linker feature test macros when cross compiling with Clang

commit 86a9df597cdd564d2d29c65897bcad42519e3678 upstream.

I was not seeing my linker flags getting added when using ld-option when
cross compiling with Clang. Upon investigation, this seems to be due to
a difference in how GCC vs Clang handle cross compilation.

GCC is configured at build time to support one backend, that is implicit
when compiling.  Clang is explicit via the use of `-target <triple>` and
ships with all supported backends by default.

GNU Make feature test macros that compile then link will always fail
when cross compiling with Clang unless Clang's triple is passed along to
the compiler. For example:

$ clang -x c /dev/null -c -o temp.o
$ aarch64-linux-android/bin/ld -E temp.o
aarch64-linux-android/bin/ld:
unknown architecture of input file `temp.o' is incompatible with
aarch64 output
aarch64-linux-android/bin/ld:
warning: cannot find entry symbol _start; defaulting to
0000000000400078
$ echo $?
1

$ clang -target aarch64-linux-android- -x c /dev/null -c -o temp.o
$ aarch64-linux-android/bin/ld -E temp.o
aarch64-linux-android/bin/ld:
warning: cannot find entry symbol _start; defaulting to 00000000004002e4
$ echo $?
0

This causes conditional checks that invoke $(CC) without the target
triple, then $(LD) on the result, to always fail.

Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/ucma: Don't allow join attempts for unsupported AF family

commit 0c81ffc60d5280991773d17e84bda605387148b1 upstream.

Users can provide garbage while calling to ucma_join_ip_multicast(),
it will indirectly cause to rdma_addr_size() return 0, making the
call to ucma_process_join(), which had the right checks, but it is
better to check the input as early as possible.

The following crash from syzkaller revealed it.

kernel BUG at lib/string.c:1052!
invalid opcode: 0000 [#1] SMP KASAN Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 4113 Comm: syz-executor0 Not tainted 4.16.0-rc5+ #261
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:fortify_panic+0x13/0x20 lib/string.c:1051
RSP: 0018:ffff8801ca81f8f0 EFLAGS: 00010286
RAX: 0000000000000022 RBX: 1ffff10039503f23 RCX: 0000000000000000
RDX: 0000000000000022 RSI: 1ffff10039503ed3 RDI: ffffed0039503f12
RBP: ffff8801ca81f8f0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000006 R11: 0000000000000000 R12: ffff8801ca81f998
R13: ffff8801ca81f938 R14: ffff8801ca81fa58 R15: 000000000000fa00
FS:  0000000000000000(0000) GS:ffff8801db200000(0063) knlGS:000000000a12a900
CS:  0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: 0000000008138024 CR3: 00000001cbb58004 CR4: 00000000001606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 memcpy include/linux/string.h:344 [inline]
 ucma_join_ip_multicast+0x36b/0x3b0 drivers/infiniband/core/ucma.c:1421
 ucma_write+0x2d6/0x3d0 drivers/infiniband/core/ucma.c:1633
 __vfs_write+0xef/0x970 fs/read_write.c:480
 vfs_write+0x189/0x510 fs/read_write.c:544
 SYSC_write fs/read_write.c:589 [inline]
 SyS_write+0xef/0x220 fs/read_write.c:581
 do_syscall_32_irqs_on arch/x86/entry/common.c:330 [inline]
 do_fast_syscall_32+0x3ec/0xf9f arch/x86/entry/common.c:392
 entry_SYSENTER_compat+0x70/0x7f arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f9ec99
RSP: 002b:00000000ff8172cc EFLAGS: 00000282 ORIG_RAX: 0000000000000004
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000020000100
RDX: 0000000000000063 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Code: 08 5b 41 5c 41 5d 41 5e 41 5f 5d c3 0f 0b 48 89 df e8 42 2c e3 fb eb de
55 48 89 fe 48 c7 c7 80 75 98 86 48 89 e5 e8 85 95 94 fb <0f> 0b 90 90 90 90
90 90 90 90 90 90 90 55 48 89 e5 41 57 41 56
RIP: fortify_panic+0x13/0x20 lib/string.c:1051 RSP: ffff8801ca81f8f0

Fixes: 5bc2b7b397b0 ("RDMA/ucma: Allow user space to specify AF_IB when joining multicast")
Reported-by: <syzbot+2287ac532caa81900a4e@syzkaller.appspotmail.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/ucma: Fix access to non-initialized CM_ID object

commit 7688f2c3bbf55e52388e37ac5d63ca471a7712e1 upstream.

The attempt to join multicast group without ensuring that CMA device
exists will lead to the following crash reported by syzkaller.

[   64.076794] BUG: KASAN: null-ptr-deref in rdma_join_multicast+0x26e/0x12c0
[   64.076797] Read of size 8 at addr 00000000000000b0 by task join/691
[   64.076797]
[   64.076800] CPU: 1 PID: 691 Comm: join Not tainted 4.16.0-rc1-00219-gb97853b65b93 #23
[   64.076802] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-proj4
[   64.076803] Call Trace:
[   64.076809]  dump_stack+0x5c/0x77
[   64.076817]  kasan_report+0x163/0x380
[   64.085859]  ? rdma_join_multicast+0x26e/0x12c0
[   64.086634]  rdma_join_multicast+0x26e/0x12c0
[   64.087370]  ? rdma_disconnect+0xf0/0xf0
[   64.088579]  ? __radix_tree_replace+0xc3/0x110
[   64.089132]  ? node_tag_clear+0x81/0xb0
[   64.089606]  ? idr_alloc_u32+0x12e/0x1a0
[   64.090517]  ? __fprop_inc_percpu_max+0x150/0x150
[   64.091768]  ? tracing_record_taskinfo+0x10/0xc0
[   64.092340]  ? idr_alloc+0x76/0xc0
[   64.092951]  ? idr_alloc_u32+0x1a0/0x1a0
[   64.093632]  ? ucma_process_join+0x23d/0x460
[   64.094510]  ucma_process_join+0x23d/0x460
[   64.095199]  ? ucma_migrate_id+0x440/0x440
[   64.095696]  ? futex_wake+0x10b/0x2a0
[   64.096159]  ucma_join_multicast+0x88/0xe0
[   64.096660]  ? ucma_process_join+0x460/0x460
[   64.097540]  ? _copy_from_user+0x5e/0x90
[   64.098017]  ucma_write+0x174/0x1f0
[   64.098640]  ? ucma_resolve_route+0xf0/0xf0
[   64.099343]  ? rb_erase_cached+0x6c7/0x7f0
[   64.099839]  __vfs_write+0xc4/0x350
[   64.100622]  ? perf_syscall_enter+0xe4/0x5f0
[   64.101335]  ? kernel_read+0xa0/0xa0
[   64.103525]  ? perf_sched_cb_inc+0xc0/0xc0
[   64.105510]  ? syscall_exit_register+0x2a0/0x2a0
[   64.107359]  ? __switch_to+0x351/0x640
[   64.109285]  ? fsnotify+0x899/0x8f0
[   64.111610]  ? fsnotify_unmount_inodes+0x170/0x170
[   64.113876]  ? __fsnotify_update_child_dentry_flags+0x30/0x30
[   64.115813]  ? ring_buffer_record_is_on+0xd/0x20
[   64.117824]  ? __fget+0xa8/0xf0
[   64.119869]  vfs_write+0xf7/0x280
[   64.122001]  SyS_write+0xa1/0x120
[   64.124213]  ? SyS_read+0x120/0x120
[   64.126644]  ? SyS_read+0x120/0x120
[   64.128563]  do_syscall_64+0xeb/0x250
[   64.130732]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[   64.132984] RIP: 0033:0x7f5c994ade99
[   64.135699] RSP: 002b:00007f5c99b97d98 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[   64.138740] RAX: ffffffffffffffda RBX: 00000000200001e4 RCX: 00007f5c994ade99
[   64.141056] RDX: 00000000000000a0 RSI: 00000000200001c0 RDI: 0000000000000015
[   64.143536] RBP: 00007f5c99b97ec0 R08: 0000000000000000 R09: 0000000000000000
[   64.146017] R10: 0000000000000000 R11: 0000000000000246 R12: 00007f5c99b97fc0
[   64.148608] R13: 0000000000000000 R14: 00007fff660e1c40 R15: 00007f5c99b989c0
[   64.151060]
[   64.153703] Disabling lock debugging due to kernel taint
[   64.156032] BUG: unable to handle kernel NULL pointer dereference at 00000000000000b0
[   64.159066] IP: rdma_join_multicast+0x26e/0x12c0
[   64.161451] PGD 80000001d0298067 P4D 80000001d0298067 PUD 1dea39067 PMD 0
[   64.164442] Oops: 0000 [#1] SMP KASAN PTI
[   64.166817] CPU: 1 PID: 691 Comm: join Tainted: G    B 4.16.0-rc1-00219-gb97853b65b93 #23
[   64.170004] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-proj4
[   64.174985] RIP: 0010:rdma_join_multicast+0x26e/0x12c0
[   64.177246] RSP: 0018:ffff8801c8207860 EFLAGS: 00010282
[   64.179901] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff94789522
[   64.183344] RDX: 1ffffffff2d50fa5 RSI: 0000000000000297 RDI: 0000000000000297
[   64.186237] RBP: ffff8801c8207a50 R08: 0000000000000000 R09: ffffed0039040ea7
[   64.189328] R10: 0000000000000001 R11: ffffed0039040ea6 R12: 0000000000000000
[   64.192634] R13: 0000000000000000 R14: ffff8801e2022800 R15: ffff8801d4ac2400
[   64.196105] FS:  00007f5c99b98700(0000) GS:ffff8801e5d00000(0000) knlGS:0000000000000000
[   64.199211] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   64.202046] CR2: 00000000000000b0 CR3: 00000001d1c48004 CR4: 00000000003606a0
[   64.205032] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   64.208221] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   64.211554] Call Trace:
[   64.213464]  ? rdma_disconnect+0xf0/0xf0
[   64.216124]  ? __radix_tree_replace+0xc3/0x110
[   64.219337]  ? node_tag_clear+0x81/0xb0
[   64.222140]  ? idr_alloc_u32+0x12e/0x1a0
[   64.224422]  ? __fprop_inc_percpu_max+0x150/0x150
[   64.226588]  ? tracing_record_taskinfo+0x10/0xc0
[   64.229763]  ? idr_alloc+0x76/0xc0
[   64.232186]  ? idr_alloc_u32+0x1a0/0x1a0
[   64.234505]  ? ucma_process_join+0x23d/0x460
[   64.237024]  ucma_process_join+0x23d/0x460
[   64.240076]  ? ucma_migrate_id+0x440/0x440
[   64.243284]  ? futex_wake+0x10b/0x2a0
[   64.245302]  ucma_join_multicast+0x88/0xe0
[   64.247783]  ? ucma_process_join+0x460/0x460
[   64.250841]  ? _copy_from_user+0x5e/0x90
[   64.253878]  ucma_write+0x174/0x1f0
[   64.257008]  ? ucma_resolve_route+0xf0/0xf0
[   64.259877]  ? rb_erase_cached+0x6c7/0x7f0
[   64.262746]  __vfs_write+0xc4/0x350
[   64.265537]  ? perf_syscall_enter+0xe4/0x5f0
[   64.267792]  ? kernel_read+0xa0/0xa0
[   64.270358]  ? perf_sched_cb_inc+0xc0/0xc0
[   64.272575]  ? syscall_exit_register+0x2a0/0x2a0
[   64.275367]  ? __switch_to+0x351/0x640
[   64.277700]  ? fsnotify+0x899/0x8f0
[   64.280530]  ? fsnotify_unmount_inodes+0x170/0x170
[   64.283156]  ? __fsnotify_update_child_dentry_flags+0x30/0x30
[   64.286182]  ? ring_buffer_record_is_on+0xd/0x20
[   64.288749]  ? __fget+0xa8/0xf0
[   64.291136]  vfs_write+0xf7/0x280
[   64.292972]  SyS_write+0xa1/0x120
[   64.294965]  ? SyS_read+0x120/0x120
[   64.297474]  ? SyS_read+0x120/0x120
[   64.299751]  do_syscall_64+0xeb/0x250
[   64.301826]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[   64.304352] RIP: 0033:0x7f5c994ade99
[   64.306711] RSP: 002b:00007f5c99b97d98 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[   64.309577] RAX: ffffffffffffffda RBX: 00000000200001e4 RCX: 00007f5c994ade99
[   64.312334] RDX: 00000000000000a0 RSI: 00000000200001c0 RDI: 0000000000000015
[   64.315783] RBP: 00007f5c99b97ec0 R08: 0000000000000000 R09: 0000000000000000
[   64.318365] R10: 0000000000000000 R11: 0000000000000246 R12: 00007f5c99b97fc0
[   64.320980] R13: 0000000000000000 R14: 00007fff660e1c40 R15: 00007f5c99b989c0
[   64.323515] Code: e8 e8 79 08 ff 4c 89 ff 45 0f b6 a7 b8 01 00 00 e8 68 7c 08 ff 49 8b 1f 4d 89 e5 49 c1 e4 04 48 8
[   64.330753] RIP: rdma_join_multicast+0x26e/0x12c0 RSP: ffff8801c8207860
[   64.332979] CR2: 00000000000000b0
[   64.335550] ---[ end trace 0c00c17a408849c1 ]---

Reported-by: <syzbot+e6aba77967bd72cbc9d6@syzkaller.appspotmail.com>
Fixes: c8f6a362bf3e ("RDMA/cma: Add multicast communication support")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: migrate the count of orphaned clocks at init

commit 99652a469df19086d594e8e89757d4081a812789 upstream.

The orphan clocks reparents should migrate any existing count from the
orphan clock to its new acestor clocks, otherwise we may have
inconsistent counts in the tree and end-up with gated critical clocks

Assuming we have two clocks, A and B.
* Clock A has CLK_IS_CRITICAL flag set.
* Clock B is an ancestor of A which can gate. Clock B gate is left
  enabled by the bootloader.

Step 1: Clock A is registered. Since it is a critical clock, it is
enabled. The clock being still an orphan, no parent are enabled.

Step 2: Clock B is registered and reparented to clock A (potentially
through several other clocks). We are now in situation where the enable
count of clock A is 1 while the enable count of its ancestors is 0, which
is not good.

Step 3: in lateinit, clk_disable_unused() is called, the enable_count of
clock B being 0, clock B is gated and and critical clock A actually gets
disabled.

This situation was found while adding fdiv_clk gates to the meson8b
platform.  These clocks parent clk81 critical clock, which is the mother
of all peripheral clocks in this system. Because of the issue described
here, the system is crashing when clk_disable_unused() is called.

The situation is solved by reverting
commit f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration").
To avoid breaking again the situation described in this commit
description, enabling critical clock should be done before walking the
orphan list. This way, a parent critical clock may not be accidentally
disabled due to the CLK_OPS_PARENT_ENABLE mechanism.

Fixes: f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration")
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/core: Do not use invalid destination in determining port reuse

commit 9dea9a2ff61c5efb4d4937ae23b14babd25a5547 upstream.

cma_port_is_unique() allows local port reuse if the quad (source
address and port, destination address and port) for this connection
is unique. However, if the destination info is zero or unspecified, it
can't make a correct decision but still allows port reuse. For example,
sometimes rdma_bind_addr() is called with unspecified destination and
reusing the port can lead to creating a connection with a duplicate quad,
after the destination is resolved. The issue manifests when MPI scale-up
tests hang after the duplicate quad is used.

Set the destination address family and add checks for zero destination
address and port to prevent source port reuse based on invalid destination.

Fixes: 19b752a19dce ("IB/cma: Allow port reuse for rdma_id")
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_pci: Don't fail on multiport card class

commit e7f3e99cb1a667d04d60d02957fbed58b50d4e5a upstream.

Do not fail on multiport cards in serial_pci_is_class_communication().

It restores behaviour for SUNIX multiport cards, that enumerated by
class and have a custom board data.

Moreover it allows users to reenumerate port-by-port from user space.

Fixes: 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix out-of-bounds read in create_raw_packet_qp_rq

commit 2c292dbb398ee46fc1343daf6c3cf9715a75688e upstream.

Add a check for the length of the qpin structure to prevent out-of-bounds reads

BUG: KASAN: slab-out-of-bounds in create_raw_packet_qp+0x114c/0x15e2
Read of size 8192 at addr ffff880066b99290 by task syz-executor3/549

CPU: 3 PID: 549 Comm: syz-executor3 Not tainted 4.15.0-rc2+ #27 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
 dump_stack+0x8d/0xd4
 print_address_description+0x73/0x290
 kasan_report+0x25c/0x370
 ? create_raw_packet_qp+0x114c/0x15e2
 memcpy+0x1f/0x50
 create_raw_packet_qp+0x114c/0x15e2
 ? create_raw_packet_qp_tis.isra.28+0x13d/0x13d
 ? lock_acquire+0x370/0x370
 create_qp_common+0x2245/0x3b50
 ? destroy_qp_user.isra.47+0x100/0x100
 ? kasan_kmalloc+0x13d/0x170
 ? sched_clock_cpu+0x18/0x180
 ? fs_reclaim_acquire.part.15+0x5/0x30
 ? __lock_acquire+0xa11/0x1da0
 ? sched_clock_cpu+0x18/0x180
 ? kmem_cache_alloc_trace+0x17e/0x310
 ? mlx5_ib_create_qp+0x30e/0x17b0
 mlx5_ib_create_qp+0x33d/0x17b0
 ? sched_clock_cpu+0x18/0x180
 ? create_qp_common+0x3b50/0x3b50
 ? lock_acquire+0x370/0x370
 ? __radix_tree_lookup+0x180/0x220
 ? uverbs_try_lock_object+0x68/0xc0
 ? rdma_lookup_get_uobject+0x114/0x240
 create_qp.isra.5+0xce4/0x1e20
 ? ib_uverbs_ex_create_cq_cb+0xa0/0xa0
 ? copy_ah_attr_from_uverbs.isra.2+0xa00/0xa00
 ? ib_uverbs_cq_event_handler+0x160/0x160
 ? __might_fault+0x17c/0x1c0
 ib_uverbs_create_qp+0x21b/0x2a0
 ? ib_uverbs_destroy_cq+0x2e0/0x2e0
 ib_uverbs_write+0x55a/0xad0
 ? ib_uverbs_destroy_cq+0x2e0/0x2e0
 ? ib_uverbs_destroy_cq+0x2e0/0x2e0
 ? ib_uverbs_open+0x760/0x760
 ? futex_wake+0x147/0x410
 ? check_prev_add+0x1680/0x1680
 ? do_futex+0x3d3/0xa60
 ? sched_clock_cpu+0x18/0x180
 __vfs_write+0xf7/0x5c0
 ? ib_uverbs_open+0x760/0x760
 ? kernel_read+0x110/0x110
 ? lock_acquire+0x370/0x370
 ? __fget+0x264/0x3b0
 vfs_write+0x18a/0x460
 SyS_write+0xc7/0x1a0
 ? SyS_read+0x1a0/0x1a0
 ? trace_hardirqs_on_thunk+0x1a/0x1c
 entry_SYSCALL_64_fastpath+0x18/0x85
RIP: 0033:0x4477b9
RSP: 002b:00007f1822cadc18 EFLAGS: 00000292 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00000000004477b9
RDX: 0000000000000070 RSI: 000000002000a000 RDI: 0000000000000005
RBP: 0000000000708000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000292 R12: 00000000ffffffff
R13: 0000000000005d70 R14: 00000000006e6e30 R15: 0000000020010ff0

Allocated by task 549:
 __kmalloc+0x15e/0x340
 kvmalloc_node+0xa1/0xd0
 create_user_qp.isra.46+0xd42/0x1610
 create_qp_common+0x2e63/0x3b50
 mlx5_ib_create_qp+0x33d/0x17b0
 create_qp.isra.5+0xce4/0x1e20
 ib_uverbs_create_qp+0x21b/0x2a0
 ib_uverbs_write+0x55a/0xad0
 __vfs_write+0xf7/0x5c0
 vfs_write+0x18a/0x460
 SyS_write+0xc7/0x1a0
 entry_SYSCALL_64_fastpath+0x18/0x85

Freed by task 368:
 kfree+0xeb/0x2f0
 kernfs_fop_release+0x140/0x180
 __fput+0x266/0x700
 task_work_run+0x104/0x180
 exit_to_usermode_loop+0xf7/0x110
 syscall_return_slowpath+0x298/0x370
 entry_SYSCALL_64_fastpath+0x83/0x85

The buggy address belongs to the object at ffff880066b99180  which
belongs to the cache kmalloc-512 of size 512 The buggy address is
located 272 bytes inside of  512-byte region [ffff880066b99180,
ffff880066b99380) The buggy address belongs to the page:
page:000000006040eedd count:1 mapcount:0 mapping:          (null)
index:0x0 compound_mapcount: 0
flags: 0x4000000000008100(slab|head)
raw: 4000000000008100 0000000000000000 0000000000000000 0000000180190019
raw: ffffea00019a7500 0000000b0000000b ffff88006c403080 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff880066b99180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 ffff880066b99200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff880066b99280: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                         ^
 ffff880066b99300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffff880066b99380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc

Cc: syzkaller <syzkaller@googlegroups.com>
Fixes: 0fb2ed66a14c ("IB/mlx5: Add create and destroy functionality for Raw Packet QP")
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix integer overflows in mlx5_ib_create_srq

commit c2b37f76485f073f020e60b5954b6dc4e55f693c upstream.

This patch validates user provided input to prevent integer overflow due
to integer manipulation in the mlx5_ib_create_srq function.

Cc: syzkaller <syzkaller@googlegroups.com>
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mpt3sas: wait for and flush running commands on shutdown/unload

commit c666d3be99c000bb889a33353e9be0fa5808d3de upstream.

This patch finishes all outstanding SCSI IO commands (but not other commands,
e.g., task management) in the shutdown and unload paths.

It first waits for the commands to complete (this is done after setting
'ioc->remove_host = 1 ', which prevents new commands to be queued) then it
flushes commands that might still be running.

This avoids triggering error handling (e.g., abort command) for all commands
possibly completed by the adapter after interrupts disabled.

[mauricfo: introduced something in commit message.]

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mauricfo: backport to linux-4.14.y (a few updates to context lines)]
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mpt3sas: fix oops in error handlers after shutdown/unload

commit 9ff549ffb4fb4cc9a4b24d1de9dc3e68287797c4 upstream.

This patch adds checks for 'ioc->remove_host' in the SCSI error handlers, so
not to access pointers/resources potentially freed in the PCI shutdown/module
unload path.  The error handlers may be invoked after shutdown/unload,
depending on other components.

This problem was observed with kexec on a system with a mpt3sas based adapter
and an infiniband adapter which takes long enough to shutdown:

The mpt3sas driver finished shutting down / disabled interrupt handling, thus
some commands have not finished and timed out.

Since the system was still running (waiting for the infiniband adapter to
shutdown), the scsi error handler for task abort of mpt3sas was invoked, and
hit an oops -- either in scsih_abort() because 'ioc->scsi_lookup' was NULL
without commit dbec4c9040ed ("scsi: mpt3sas: lockless command submission"), or
later up in scsih_host_reset() (with or without that commit), because it
eventually called mpt3sas_base_get_iocstate().

After the above commit, the oops in scsih_abort() does not occur anymore
(_scsih_scsi_lookup_find_by_scmd() is no longer called), but that commit is
too big and out of the scope of linux-stable, where this patch might help, so
still go for the changes.

Also, this might help to prevent similar errors in the future, in case code
changes and possibly tries to access freed stuff.

Note the fix in scsih_host_reset() is still important anyway.

Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63

[ Upstream commit d087f15786021a9605b20f4c678312510be4cac1 ]

Register layout of a typical TPCC_EVT_MUX_M_N register is such that the
lowest numbered event is at the lowest byte address and highest numbered
event at highest byte address. But TPCC_EVT_MUX_60_63 register layout is
different,  in that the lowest numbered event is at the highest address
and highest numbered event is at the lowest address. Therefore, modify
ti_am335x_xbar_write() to handle TPCC_EVT_MUX_60_63 register
accordingly.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: artpec6 - set correct iv size for gcm(aes)

[ Upstream commit 6d6e71feb183aa588c849e20e7baa47cb162928a ]

The IV size should not include the 32 bit counter. Because we had the
IV size set as 16 the transform only worked when the IV input was zero
padded.

Fixes: a21eb94fc4d3 ("crypto: axis - add ARTPEC-6/7 crypto accelerator driver")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: si5351: Rename internal plls to avoid name collisions

[ Upstream commit cdba9a4fb0b53703959ac861e415816cb61aded4 ]

This drivers probe fails due to a clock name collision if a clock named
'plla' or 'pllb' is already registered when registering this drivers
internal plls.

Fix it by renaming internal plls to avoid name collisions.

Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: axi-clkgen: Correctly handle nocount bit in recalc_rate()

[ Upstream commit 063578dc5f407f67d149133818efabe457daafda ]

If the nocount bit is set the divider is bypassed and the settings for the
divider count should be ignored and a divider value of 1 should be assumed.
Handle this correctly in the driver recalc_rate() callback.

While the driver sets up the part so that the read back dividers values
yield the correct result the power-on reset settings of the part might not
reflect this and hence calling e.g. clk_get_rate() without prior calls to
clk_set_rate() will yield the wrong result.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: Don't touch hardware when reparenting during registration

[ Upstream commit f8f8f1d04494d3a6546bee3f0618c4dba31d7b72 ]

The orphan clocks reparent operation shouldn't touch the hardware
if clocks are enabled, otherwise it may get a chance to disable a
newly registered critical clock which triggers the warning below.

Assuming we have two clocks: A and B, B is the parent of A.
Clock A has flag: CLK_OPS_PARENT_ENABLE
Clock B has flag: CLK_IS_CRITICAL

Step 1:
Clock A is registered, then it becomes orphan.

Step 2:
Clock B is registered. Before clock B reach the critical clock enable
operation, orphan A will find the newly registered parent B and do
reparent operation, then parent B will be finally disabled in
__clk_set_parent_after() due to CLK_OPS_PARENT_ENABLE flag as there's
still no users of B which will then trigger the following warning.

WARNING: CPU: 0 PID: 0 at drivers/clk/clk.c:597 clk_core_disable+0xb4/0xe0
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00056-gdff1f66-dirty #1373
Hardware name: Generic DT based system
Backtrace:
[<c010c4bc>] (dump_backtrace) from [<c010c764>] (show_stack+0x18/0x1c)
 r6:600000d3 r5:00000000 r4:c0e26358 r3:00000000
[<c010c74c>] (show_stack) from [<c040599c>] (dump_stack+0xb4/0xe8)
[<c04058e8>] (dump_stack) from [<c0125c94>] (__warn+0xd8/0x104)
 r10:c0c21cd0 r9:c048aa78 r8:00000255 r7:00000009 r6:c0c1cd90 r5:00000000
 r4:00000000 r3:c0e01d34
[<c0125bbc>] (__warn) from [<c0125d74>] (warn_slowpath_null+0x28/0x30)
 r9:00000000 r8:ef00bf80 r7:c165ac4c r6:ef00bf80 r5:ef00bf80 r4:ef00bf80
[<c0125d4c>] (warn_slowpath_null) from [<c048aa78>] (clk_core_disable+0xb4/0xe0)
[<c048a9c4>] (clk_core_disable) from [<c048be88>] (clk_core_disable_lock+0x20/0x2c)
 r4:000000d3 r3:c0e0af00
[<c048be68>] (clk_core_disable_lock) from [<c048c224>] (clk_core_disable_unprepare+0x14/0x28)
 r5:00000000 r4:ef00bf80
[<c048c210>] (clk_core_disable_unprepare) from [<c048c270>] (__clk_set_parent_after+0x38/0x54)
 r4:ef00bd80 r3:000010a0
[<c048c238>] (__clk_set_parent_after) from [<c048daa8>] (clk_register+0x4d0/0x648)
 r6:ef00d500 r5:ef00bf80 r4:ef00bd80 r3:ef00bfd4
[<c048d5d8>] (clk_register) from [<c048dc30>] (clk_hw_register+0x10/0x1c)
 r9:00000000 r8:00000003 r7:00000000 r6:00000824 r5:00000001 r4:ef00d500
[<c048dc20>] (clk_hw_register) from [<c048e698>] (_register_divider+0xcc/0x120)
[<c048e5cc>] (_register_divider) from [<c048e730>] (clk_register_divider+0x44/0x54)
 r10:00000004 r9:00000003 r8:00000001 r7:00000000 r6:00000003 r5:00000001
 r4:f0810030
[<c048e6ec>] (clk_register_divider) from [<c0d3ff58>] (imx7ulp_clocks_init+0x558/0xe98)
 r7:c0e296f8 r6:c165c808 r5:00000000 r4:c165c808
[<c0d3fa00>] (imx7ulp_clocks_init) from [<c0d24db0>] (of_clk_init+0x118/0x1e0)
 r10:00000001 r9:c0e01f68 r8:00000000 r7:c0e01f60 r6:ef7f8974 r5:ef0035c0
 r4:00000006
[<c0d24c98>] (of_clk_init) from [<c0d04a50>] (time_init+0x2c/0x38)
 r10:efffed40 r9:c0d61a48 r8:c0e78000 r7:c0e07900 r6:ffffffff r5:c0e78000
 r4:00000000
[<c0d04a24>] (time_init) from [<c0d00b8c>] (start_kernel+0x218/0x394)
[<c0d00974>] (start_kernel) from [<6000807c>] (0x6000807c)
 r10:00000000 r9:410fc075 r8:6000406a r7:c0e0c930 r6:c0d61a44 r5:c0e07918
 r4:c0e78294

We know that the clk isn't enabled with any sort of prepare_count
here so we don't need to enable anything to prevent a race. And
we're holding the prepare mutex so set_rate/set_parent can't race
here either. Based on an earlier patch by Dong Aisheng.

Fixes: fc8726a2c021 ("clk: core: support clocks which requires parents enable (part 2)")
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: at91: pmc: Wait for clocks when resuming

[ Upstream commit 960e1c4d93be86d3b118fe22d4edc69e401b28b5 ]

Wait for the syncronization of all clocks when resuming, not only the
UPLL clock. Do not use regmap_read_poll_timeout, as it will call BUG()
when interrupts are masked, which is the case in here.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfsd4: permit layoutget of executable-only files

[ Upstream commit 66282ec1cf004c09083c29cb5e49019037937bbd ]

Clients must be able to read a file in order to execute it, and for pNFS
that means the client needs to be able to perform a LAYOUTGET on the file.

This behavior for executable-only files was added for OPEN in commit
a043226bc140 "nfsd4: permit read opens of executable-only files".

This fixes up xfstests generic/126 on block/scsi layouts.

Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: aspeed-evb: Add unit name to memory node

[ Upstream commit e40ed274489a5f516da120186578eb379b452ac6 ]

Fixes a warning when building with W=1.

All of the ASPEED device trees build without warnings now.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/ocrdma: Fix permissions for OCRDMA_RESET_STATS

[ Upstream commit 744820869166c8c78be891240cf5f66e8a333694 ]

Debugfs file reset_stats is created with S_IRUSR permissions,
but ocrdma_dbgfs_ops_read() doesn't support OCRDMA_RESET_STATS,
whereas ocrdma_dbgfs_ops_write() supports only OCRDMA_RESET_STATS.

The patch fixes misstype with permissions.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: Fix issues connecting with nvme initiator

[ Upstream commit e06351a002214d152142906a546006e3446d1ef7 ]

In the lpfc discovery engine, when as a nvme target, where the driver
was performing mailbox io with the adapter for port login when a NVME
PRLI is received from the host. Rather than queue and eventually get
back to sending a response after the mailbox traffic, the driver
rejected the io with an error response.

Turns out this particular initiator didn't like the rejection values
(unable to process command/command in progress) so it never attempted a
retry of the PRLI. Thus the host never established nvme connectivity
with the lpfc target.

By changing the rejection values (to Logical Busy/nothing more), the
initiator accepted the response and would retry the PRLI, resulting in
nvme connectivity.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: Fix SCSI LUN discovery when SCSI and NVME enabled

[ Upstream commit 9de416ac67b54d666327ba927a190f4b7259f4a0 ]

When enabled for both SCSI and NVME support, and connected pt2pt to a
SCSI only target, the driver nodelist entry for the remote port is left
in PRLI_ISSUE state and no SCSI LUNs are discovered. Works fine if only
configured for SCSI support.

Error was due to some of the prli points still reflecting the need to
send only 1 PRLI. On a lot of fabric configs, targets were NVME only,
which meant the fabric-reported protocol attributes were only telling
the driver one protocol or the other. Thus things worked fine. With
pt2pt, the driver must send a PRLI for both protocols as there are no
hints on what the target supports. Thus pt2pt targets were hitting the
multiple PRLI issues.

Complete the dual PRLI support. Track explicitly whether scsi (fcp) or
nvme prli's have been sent. Accurately track protocol support detected
on each node as reported by the fabric or probed by PRLI traffic.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

soc: qcom: smsm: fix child-node lookup

[ Upstream commit 8804517e9fc16c10081ff5e42e7d80704973a8e2 ]

Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.

Note that the original premature free of the parent node has already
been fixed separately.

Also note that this pattern of looking up the first child node with a
given property is rare enough that a generic helper is probably not
warranted.

Fixes: c97c4090ff72 ("soc: qcom: smsm: Add driver for Qualcomm SMSM")
Fixes: 3e8b55411468 ("soc: qcom: smsm: fix of_node refcnting problem")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip_gre: fix potential memory leak in erspan_rcv

[ Upstream commit 50670b6ee9bc4ae8f9ce3112b437987adf273245 ]

If md is NULL, tun_dst must be freed, otherwise it will cause memory
leak.

Fixes: 1a66a836da6 ("gre: add collect_md mode to ERSPAN tunnel")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip_gre: fix error path when erspan_rcv failed

[ Upstream commit dd8d5b8c5b22e31079b259b8bfb686f1fac1080a ]

When erspan_rcv call return PACKET_REJECT, we shoudn't call ipgre_rcv to
process packets again, instead send icmp unreachable message in error
path.

Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Acked-by: William Tu <u9012063@gmail.com>
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6_vti: adjust vti mtu according to mtu of lower device

[ Upstream commit 53c81e95df1793933f87748d36070a721f6cb287 ]

LTP/udp6_ipsec_vti tests fail when sending large UDP datagrams over
ip6_vti that require fragmentation and the underlying device has an
MTU smaller than 1500 plus some extra space for headers. This happens
because ip6_vti, by default, sets MTU to ETH_DATA_LEN and not updating
it depending on a destination address or link parameter. Further
attempts to send UDP packets may succeed because pmtu gets updated on
ICMPV6_PKT_TOOBIG in vti6_err().

In case the lower device has larger MTU size, e.g. 9000, ip6_vti works
but not using the possible maximum size, output packets have 1500 limit.

The above cases require manual MTU setup after ip6_vti creation. However
ip_vti already updates MTU based on lower device with ip_tunnel_bind_dev().

Here is the example when the lower device MTU is set to 9000:

  # ip a sh ltp_ns_veth2
      ltp_ns_veth2@if7: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 ...
        inet 10.0.0.2/24 scope global ltp_ns_veth2
        inet6 fd00::2/64 scope global

  # ip li add vti6 type vti6 local fd00::2 remote fd00::1
  # ip li show vti6
      vti6@NONE: <POINTOPOINT,NOARP> mtu 1500 ...
        link/tunnel6 fd00::2 peer fd00::1

After the patch:
  # ip li add vti6 type vti6 local fd00::2 remote fd00::1
  # ip li show vti6
      vti6@NONE: <POINTOPOINT,NOARP> mtu 8832 ...
        link/tunnel6 fd00::2 peer fd00::1

Reported-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/vt-d: clean up pr_irq if request_threaded_irq fails

[ Upstream commit 72d548113881dd32bf7f0b221d031e6586468437 ]

It is unlikely request_threaded_irq will fail, but if it does for some
reason we should clear iommu->pr_irq in the error path. Also
intel_svm_finish_prq shouldn't try to clean up the page request
interrupt if pr_irq is 0. Without these, if request_threaded_irq were
to fail the following occurs:

fail with no fixes:

[    0.683147] ------------[ cut here ]------------
[    0.683148] NULL pointer, cannot free irq
[    0.683158] WARNING: CPU: 1 PID: 1 at kernel/irq/irqdomain.c:1632 irq_domain_free_irqs+0x126/0x140
[    0.683160] Modules linked in:
[    0.683163] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc2 #3
[    0.683165] Hardware name:                  /NUC7i3BNB, BIOS BNKBL357.86A.0036.2017.0105.1112 01/05/2017
[    0.683168] RIP: 0010:irq_domain_free_irqs+0x126/0x140
[    0.683169] RSP: 0000:ffffc90000037ce8 EFLAGS: 00010292
[    0.683171] RAX: 000000000000001d RBX: ffff880276283c00 RCX: ffffffff81c5e5e8
[    0.683172] RDX: 0000000000000001 RSI: 0000000000000096 RDI: 0000000000000246
[    0.683174] RBP: ffff880276283c00 R08: 0000000000000000 R09: 000000000000023c
[    0.683175] R10: 0000000000000007 R11: 0000000000000000 R12: 000000000000007a
[    0.683176] R13: 0000000000000001 R14: 0000000000000000 R15: 0000010010000000
[    0.683178] FS:  0000000000000000(0000) GS:ffff88027ec80000(0000) knlGS:0000000000000000
[    0.683180] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    0.683181] CR2: 0000000000000000 CR3: 0000000001c09001 CR4: 00000000003606e0
[    0.683182] Call Trace:
[    0.683189]  intel_svm_finish_prq+0x3c/0x60
[    0.683191]  free_dmar_iommu+0x1ac/0x1b0
[    0.683195]  init_dmars+0xaaa/0xaea
[    0.683200]  ? klist_next+0x19/0xc0
[    0.683203]  ? pci_do_find_bus+0x50/0x50
[    0.683205]  ? pci_get_dev_by_id+0x52/0x70
[    0.683208]  intel_iommu_init+0x498/0x5c7
[    0.683211]  pci_iommu_init+0x13/0x3c
[    0.683214]  ? e820__memblock_setup+0x61/0x61
[    0.683217]  do_one_initcall+0x4d/0x1a0
[    0.683220]  kernel_init_freeable+0x186/0x20e
[    0.683222]  ? set_debug_rodata+0x11/0x11
[    0.683225]  ? rest_init+0xb0/0xb0
[    0.683226]  kernel_init+0xa/0xff
[    0.683229]  ret_from_fork+0x1f/0x30
[    0.683259] Code: 89 ee 44 89 e7 e8 3b e8 ff ff 5b 5d 44 89 e7 44 89 ee 41 5c 41 5d 41 5e e9 a8 84 ff ff 48 c7 c7 a8 71 a7 81 31 c0 e8 6a d3 f9 ff <0f> ff 5b 5d 41 5c 41 5d 41 5
e c3 0f 1f 44 00 00 66 2e 0f 1f 84
[    0.683285] ---[ end trace f7650e42792627ca ]---

with iommu->pr_irq = 0, but no check in intel_svm_finish_prq:

[    0.669561] ------------[ cut here ]------------
[    0.669563] Trying to free already-free IRQ 0
[    0.669573] WARNING: CPU: 3 PID: 1 at kernel/irq/manage.c:1546 __free_irq+0xa4/0x2c0
[    0.669574] Modules linked in:
[    0.669577] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc2 #4
[    0.669579] Hardware name:                  /NUC7i3BNB, BIOS BNKBL357.86A.0036.2017.0105.1112 01/05/2017
[    0.669581] RIP: 0010:__free_irq+0xa4/0x2c0
[    0.669582] RSP: 0000:ffffc90000037cc0 EFLAGS: 00010082
[    0.669584] RAX: 0000000000000021 RBX: 0000000000000000 RCX: ffffffff81c5e5e8
[    0.669585] RDX: 0000000000000001 RSI: 0000000000000086 RDI: 0000000000000046
[    0.669587] RBP: 0000000000000000 R08: 0000000000000000 R09: 000000000000023c
[    0.669588] R10: 0000000000000007 R11: 0000000000000000 R12: ffff880276253960
[    0.669589] R13: ffff8802762538a4 R14: ffff880276253800 R15: ffff880276283600
[    0.669593] FS:  0000000000000000(0000) GS:ffff88027ed80000(0000) knlGS:0000000000000000
[    0.669594] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    0.669596] CR2: 0000000000000000 CR3: 0000000001c09001 CR4: 00000000003606e0
[    0.669602] Call Trace:
[    0.669616]  free_irq+0x30/0x60
[    0.669620]  intel_svm_finish_prq+0x34/0x60
[    0.669623]  free_dmar_iommu+0x1ac/0x1b0
[    0.669627]  init_dmars+0xaaa/0xaea
[    0.669631]  ? klist_next+0x19/0xc0
[    0.669634]  ? pci_do_find_bus+0x50/0x50
[    0.669637]  ? pci_get_dev_by_id+0x52/0x70
[    0.669639]  intel_iommu_init+0x498/0x5c7
[    0.669642]  pci_iommu_init+0x13/0x3c
[    0.669645]  ? e820__memblock_setup+0x61/0x61
[    0.669648]  do_one_initcall+0x4d/0x1a0
[    0.669651]  kernel_init_freeable+0x186/0x20e
[    0.669653]  ? set_debug_rodata+0x11/0x11
[    0.669656]  ? rest_init+0xb0/0xb0
[    0.669658]  kernel_init+0xa/0xff
[    0.669661]  ret_from_fork+0x1f/0x30
[    0.669662] Code: 7a 08 75 0e e9 c3 01 00 00 4c 39 7b 08 74 57 48 89 da 48 8b 5a 18 48 85 db 75 ee 89 ee 48 c7 c7 78 67 a7 81 31 c0 e8 4c 37 fa ff <0f> ff 48 8b 34 24 4c 89 ef e
8 0e 4c 68 00 49 8b 46 40 48 8b 80
[    0.669688] ---[ end trace 58a470248700f2fc ]---

Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: rockchip: enable clock when reading pin direction register

[ Upstream commit 5c9d8c4f6b8168738a26bcf288516cc3a0886810 ]

We generally leave the GPIO clock disabled, unless an interrupt is
requested or we're accessing IO registers. We forgot to do this for the
->get_direction() callback, which means we can sometimes [1] get
incorrect results [2] from, e.g., /sys/kernel/debug/gpio.

Enable the clock, so we get the right results!

[1] Sometimes, because many systems have 1 or mor interrupt requested on
each GPIO bank, so they always leave their clock on.

[2] Incorrect, meaning the register returns 0, and so we interpret that
as "input".

Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: Really force states during suspend/resume

[ Upstream commit 981ed1bfbc6c4660b2ddaa8392893e20a6255048 ]

In case a platform only defaults a "default" set of pins, but not a
"sleep" set of pins, and this particular platform suspends and resumes
in a way that the pin states are not preserved by the hardware, when we
resume, we would call pinctrl_single_resume() -> pinctrl_force_default()
-> pinctrl_select_state() and the first thing we do is check that the
pins state is the same as before, and do nothing.

In order to fix this, decouple the actual state change from
pinctrl_select_state() and move it pinctrl_commit_state(), while keeping
the p->state == state check in pinctrl_select_state() not to change the
caller assumptions. pinctrl_force_sleep() and pinctrl_force_default()
are updated to bypass the state check by calling pinctrl_commit_state().

[Linus Walleij]
The forced pin control states are currently only used in some pin
controller drivers that grab their own reference to their own pins.
This is equal to the pin control hogs: pins taken by pin control
devices since there are no corresponding device in the Linux device
hierarchy, such as memory controller lines or unused GPIO lines,
or GPIO lines that are used orthogonally from the GPIO subsystem
but pincontrol-wise managed as hogs (non-strict mode, allowing
simultaneous use by GPIO and pin control). For this case forcing
the state from the drivers' suspend()/resume() callbacks makes
sense and should semantically match the name of the function.

Fixes: 6e5e959dde0d ("pinctrl: API changes to support multiple states per device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: davinci: fix a debug printk

[ Upstream commit 4f6c11044f512356cb63d3df0f3b38db79dc6736 ]

Two orthogonal changesets caused a breakage at a printk
inside davinci. Commit a2d17962c9ca
("[media] davinci: Switch from V4L2 OF to V4L2 fwnode")
made davinci to use struct fwnode_handle instead of
struct device_node. Commit 68d9c47b1679
("media: Convert to using %pOF instead of full_name")
changed the printk to not use ->full_name, but, instead,
to rely on %pOF.

With both patches applied, the Kernel will do the wrong
thing, as warned by smatch:
drivers/media/platform/davinci/vpif_capture.c:1399 vpif_async_bound() error: '%pOF' expects argument of type 'struct device_node*', argument 5 has type 'void*'

So, change the logic to actually print the device name
that was obtained before the print logic.

Fixes: 68d9c47b1679 ("media: Convert to using %pOF instead of full_name")
Fixes: a2d17962c9ca ("[media] davinci: Switch from V4L2 OF to V4L2 fwnode")

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: rcar: Handle rcar_pcie_parse_request_of_pci_ranges() failures

[ Upstream commit 83c75ddd816e979802bd244ad494139f28152921 ]

rcar_pcie_parse_request_of_pci_ranges() can fail and return an error
code, but this is not checked nor handled.

Fix this by adding the missing error handling.

Fixes: 5d2917d469faab72 ("PCI: rcar: Convert to DT resource parsing API")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: endpoint: Fix find_first_zero_bit() usage

[ Upstream commit 35ad61921f495ee14915d185de79478c1737b4da ]

find_first_zero_bit()'s parameter 'size' is defined in bits,
not in bytes.

Calling find_first_zero_bit() with the wrong size unit
will lead to insidious bugs.

Fix this by calling find_first_zero_bit() with size BITS_PER_LONG,
rather than sizeof() and add missing find_first_zero_bit() return
handling.

Fixes: d74679911610 ("PCI: endpoint: Introduce configfs entry for configuring EP functions")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: designware-ep: Fix ->get_msi() to check MSI_EN bit

[ Upstream commit a134a457ed985dca8cce7ac4ea66129ea70eba73 ]

->get_msi() now checks MSI_EN bit in the MSI CAPABILITY register to
find whether the host supports MSI instead of using the
MSI ADDRESS in the MSI CAPABILITY register.

This fixes the issue with the following sequence
  'modprobe pci_endpoint_test' enables MSI
  'rmmod pci_endpoint_test' disables MSI but MSI address (in EP's
capability register) has a valid value
  'modprobe pci_endpoint_test no_msi=1' - Since MSI address (in EP's
capability register) has a valid value (set during the previous
insertion of the module), EP thinks host supports MSI.

Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

coresight: Fix disabling of CoreSight TPIU

[ Upstream commit 11595db8e17faaa05fadc25746c870e31276962f ]

The CoreSight TPIU should be disabled when tracing to other sinks to allow
them to operate at full bandwidth.

This patch fixes tpiu_disable_hw() to correctly disable the TPIU by
configuring the TPIU to stop on flush, initiating a manual flush, waiting
for the flush to complete and then waits for the TPIU to indicate it has
stopped.

Signed-off-by: Robert Walker <robert.walker@arm.com>
Tested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pty: cancel pty slave port buf's work in tty_release

[ Upstream commit 2b022ab7542df60021ab57854b3faaaf42552eaf ]

In case that CONFIG_SLUB_DEBUG is on and pty is used, races between
release_one_tty and flush_to_ldisc work threads may happen and lead
to use-after-free condition on tty->link->port. Because SLUB_DEBUG
is turned on, freed tty->link->port is filled with POISON_FREE value.
So far without SLUB_DEBUG, port was filled with zero and flush_to_ldisc
could return without a problem by checking if tty is NULL.

CPU 0                                 CPU 1
-----                                 -----
release_tty                           pty_write
   cancel_work_sync(tty)                 to = tty->link
   tty_kref_put(tty->link)               tty_schedule_flip(to->port)
      << workqueue >>                 ...
      release_one_tty                 ...
         pty_cleanup                  ...
            kfree(tty->link->port)       << workqueue >>
                                         flush_to_ldisc
                                            tty = READ_ONCE(port->itty)
                                            tty is 0x6b6b6b6b6b6b6b6b
                                            !!PANIC!! access tty->ldisc

 Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b93
 pgd = ffffffc0eb1c3000
 [6b6b6b6b6b6b6b93] *pgd=0000000000000000, *pud=0000000000000000
 ------------[ cut here ]------------
 Kernel BUG at ffffff800851154c [verbose debug info unavailable]
 Internal error: Oops - BUG: 96000004 [#1] PREEMPT SMP
 CPU: 3 PID: 265 Comm: kworker/u8:9 Tainted: G        W 3.18.31-g0a58eeb #1
 Hardware name: Qualcomm Technologies, Inc. MSM 8996pro v1.1 + PMI8996 Carbide (DT)
 Workqueue: events_unbound flush_to_ldisc
 task: ffffffc0ed610ec0 ti: ffffffc0ed624000 task.ti: ffffffc0ed624000
 PC is at ldsem_down_read_trylock+0x0/0x4c
 LR is at tty_ldisc_ref+0x24/0x4c
 pc : [<ffffff800851154c>] lr : [<ffffff800850f6c0>] pstate: 80400145
 sp : ffffffc0ed627cd0
 x29: ffffffc0ed627cd0 x28: 0000000000000000
 x27: ffffff8009e05000 x26: ffffffc0d382cfa0
 x25: 0000000000000000 x24: ffffff800a012f08
 x23: 0000000000000000 x22: ffffffc0703fbc88
 x21: 6b6b6b6b6b6b6b6b x20: 6b6b6b6b6b6b6b93
 x19: 0000000000000000 x18: 0000000000000001
 x17: 00e80000f80d6f53 x16: 0000000000000001
 x15: 0000007f7d826fff x14: 00000000000000a0
 x13: 0000000000000000 x12: 0000000000000109
 x11: 0000000000000000 x10: 0000000000000000
 x9 : ffffffc0ed624000 x8 : ffffffc0ed611580
 x7 : 0000000000000000 x6 : ffffff800a42e000
 x5 : 00000000000003fc x4 : 0000000003bd1201
 x3 : 0000000000000001 x2 : 0000000000000001
 x1 : ffffff800851004c x0 : 6b6b6b6b6b6b6b93

Signed-off-by: Sahara <keun-o.park@darkmatter.ae>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/omap: DMM: Check for DMM readiness after successful transaction commit

[ Upstream commit b7ea6b286c4051e043f691781785e3c4672f014a ]

Check the status of the DMM engine after it is reported that the
transaction was completed as in rare cases the engine might not reached a
working state.

The wait_status() will print information in case the DMM is not reached the
expected state and the dmm_txn_commit() will return with an error code to
make sure that we are not continuing with a broken setup.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci-xenon: wait 5ms after set 1.8V signal enable

[ Upstream commit 8d876bf472dba73c015cea9feea80dcb80626a7c ]

According to SD spec 3.00 3.6.1 signal voltage switch
procedure step 6~8,
(6) Set 1.8V Signal Enable in the Host Control 2 register.
(7) Wait 5ms. 1.8V voltage regulator shall be stable within this period.
(8) If 1.8V Signal Enable is cleared by Host Controller, go to step (12).
Host should wait 5ms after set 1.8V signal enable bit in
Host Control 2 register and check if 1.8V is stable or not.

But current code checks this bit right after set it.
On some platforms with xenon controller found the bit is
cleared right away and host reports "1.8V regulator output
did not became stable" and 5ms delay can help.

Implement voltage_switch callback for xenon controller to add 5ms
delay to make sure the 1.8V signal enable bit is set by controller.

Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

omapdrm: panel: fix compatible vendor string for td028ttec1

[ Upstream commit c1b9d4c75cd549e08bd0596d7f9dcc20f7f6e8fa ]

The vendor name was "toppoly" but other panels and the vendor list
have defined it as "tpo". So let's fix it in driver and bindings.

We keep the old definition in parallel to stay compatible with
potential older DTB setup.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vgacon: Set VGA struct resource types

[ Upstream commit c82084117f79bcae085e40da526253736a247120 ]

Set the resource type when we reserve VGA-related I/O port resources.

The resource code doesn't actually look at the type, so it inserts
resources without a type in the tree correctly even without this change.
But if we ever print a resource without a type, it looks like this:

  vga+ [??? 0x000003c0-0x000003df flags 0x0]

Setting the type means it will be printed correctly as:

  vga+ [io  0x000003c0-0x000003df]

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iser-target: avoid reinitializing rdma contexts for isert commands

[ Upstream commit 66f53e6f5400578bae58db0c06d85a8820831f40 ]

isert commands that failed during isert_rdma_rw_ctx_post() are queued to
Queue-Full(QF) queue and are scheduled to be reposted during queue-full
queue processing. During this reposting, the rdma contexts are initialised
again in isert_rdma_rw_ctx_post(), which is leaking significant memory.

unreferenced object 0xffff8830201d9640 (size 64):
  comm "kworker/0:2", pid 195, jiffies 4295374851 (age 4528.436s)
  hex dump (first 32 bytes):
    00 60 8b cb 2e 00 00 00 00 10 00 00 00 00 00 00  .`..............
    00 90 e3 cb 2e 00 00 00 00 10 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8170711e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811f8ba5>] __kmalloc+0x125/0x2b0
    [<ffffffffa046b24f>] rdma_rw_ctx_init+0x15f/0x6f0 [ib_core]
    [<ffffffffa07ab644>] isert_rdma_rw_ctx_post+0xc4/0x3c0 [ib_isert]
    [<ffffffffa07ad972>] isert_put_datain+0x112/0x1c0 [ib_isert]
    [<ffffffffa07dddce>] lio_queue_data_in+0x2e/0x30 [iscsi_target_mod]
    [<ffffffffa076c322>] target_qf_do_work+0x2b2/0x4b0 [target_core_mod]
    [<ffffffff81080c3b>] process_one_work+0x1db/0x5d0
    [<ffffffff8108107d>] worker_thread+0x4d/0x3e0
    [<ffffffff81088667>] kthread+0x117/0x150
    [<ffffffff81713fa7>] ret_from_fork+0x27/0x40
    [<ffffffffffffffff>] 0xffffffffffffffff

Here is patch to use the older rdma contexts while reposting
the isert commands intead of reinitialising them.

Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/umem: Fix use of npages/nmap fields

[ Upstream commit edf1a84fe37c51290e2c88154ecaf48dadff3d27 ]

In ib_umem structure npages holds original number of sg entries, while
nmap is number of DMA blocks returned by dma_map_sg.

Fixes: c5d76f130b28 ('IB/core: Add umem function to read data from user-space')
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/cma: Use correct size when writing netlink stats

[ Upstream commit 7baaa49af3716fb31877c61f59b74d029ce15b75 ]

The code was using the src size when formatting the dst. They are almost
certainly the same value but it reads wrong.

Fixes: ce117ffac2e9 ("RDMA/cma: Export AF_IB statistics")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/ipoib: Avoid memory leak if the SA returns a different DGID

[ Upstream commit 439000892ee17a9c92f1e4297818790ef8bb4ced ]

The ipoib path database is organized around DGIDs from the LLADDR, but the
SA is free to return a different GID when asked for path. This causes a
bug because the SA's modified DGID is copied into the database key, even
though it is no longer the correct lookup key, causing a memory leak and
other malfunctions.

Ensure the database key does not change after the SA query completes.

Demonstration of the bug is as  follows
ipoib wants to send to GID fe80:0000:0000:0000:0002:c903:00ef:5ee2, it
creates new record in the DB with that gid as a key, and issues a new
request to the SM.
Now, the SM from some reason returns path-record with other SGID (for
example, 2001:0000:0000:0000:0002:c903:00ef:5ee2 that contains the local
subnet prefix) now ipoib will overwrite the current entry with the new
one, and if new request to the original GID arrives ipoib  will not find
it in the DB (was overwritten) and will create new record that in its
turn will also be overwritten by the response from the SM, and so on
till the driver eats all the device memory.

Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: ac100: Fix multiple race conditions

[ Upstream commit 994ec64c0a193940be7a6fd074668b9446d3b6c3 ]

The probe function is not allowed to fail after registering the RTC because
the following may happen:

CPU0:                                CPU1:
sys_load_module()
 do_init_module()
  do_one_initcall()
   cmos_do_probe()
    rtc_device_register()
     __register_chrdev()
     cdev->owner = struct module*
                                     open("/dev/rtc0")
    rtc_device_unregister()
  module_put()
  free_module()
   module_free(mod->module_core)
   /* struct module *module is now
      freed */
                                      chrdev_open()
                                       spin_lock(cdev_lock)
                                       cdev_get()
                                        try_module_get()
                                         module_is_live()
                                         /* dereferences already
                                            freed struct module* */

Also, the interrupt handler: ac100_rtc_irq() is dereferencing chip->rtc but
this may still be NULL when it is called, resulting in:
Unable to handle kernel NULL pointer dereference at virtual address 00000194
pgd = (ptrval)
[00000194] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 72 Comm: irq/71-ac100-rt Not tainted 4.15.0-rc1-next-20171201-dirty #120
Hardware name: Allwinner sun8i Family
task: (ptrval) task.stack: (ptrval)
PC is at mutex_lock+0x14/0x3c
LR is at ac100_rtc_irq+0x38/0xc8
pc : [<c06543a4>]    lr : [<c04d9a2c>]    psr: 60000053
sp : ee9c9f28  ip : 00000000  fp : ee9adfdc
r10: 00000000  r9 : c0a04c48  r8 : c015ed18
r7 : ee9bd600  r6 : ee9c9f28  r5 : ee9af590  r4 : c0a04c48
r3 : ef3cb3c0  r2 : 00000000  r1 : ee9af590  r0 : 00000194
Flags: nZCv  IRQs on  FIQs off  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: 4000406a  DAC: 00000051
Process irq/71-ac100-rt (pid: 72, stack limit = 0x(ptrval))
Stack: (0xee9c9f28 to 0xee9ca000)
9f20:                   00000000 7c2fd1be c015ed18 ee9adf40 ee9c0400 ee9c0400
9f40: ee9adf40 c015ed34 ee9c8000 ee9adf64 ee9c0400 c015f040 ee9adf80 00000000
9f60: c015ee24 7c2fd1be ee9adfc0 ee9adf80 00000000 ee9c8000 ee9adf40 c015eef4
9f80: ef1eba34 c0138f14 ee9c8000 ee9adf80 c0138df4 00000000 00000000 00000000
9fa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
[<c06543a4>] (mutex_lock) from [<c04d9a2c>] (ac100_rtc_irq+0x38/0xc8)
[<c04d9a2c>] (ac100_rtc_irq) from [<c015ed34>] (irq_thread_fn+0x1c/0x54)
[<c015ed34>] (irq_thread_fn) from [<c015f040>] (irq_thread+0x14c/0x214)
[<c015f040>] (irq_thread) from [<c0138f14>] (kthread+0x120/0x150)
[<c0138f14>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)

Solve both issues by moving to
devm_rtc_allocate_device()/rtc_register_device()

Reported-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: s5p-mfc: Fix lock contention - request_firmware() once

[ Upstream commit f45ce9877561044090010e0eb0fad644232ded04 ]

Driver calls request_firmware() whenever the device is opened for the
first time. As the device gets opened and closed, dev->num_inst == 1
is true several times. This is not necessary since the firmware is saved
in the fw_buf. s5p_mfc_load_firmware() copies the buffer returned by
the request_firmware() to dev->fw_buf.

fw_buf sticks around until it gets released from s5p_mfc_remove(), hence
there is no need to keep requesting firmware and copying it to fw_buf.

This might have been overlooked when changes are made to free fw_buf from
the device release interface s5p_mfc_release().

Fix s5p_mfc_load_firmware() to call request_firmware() once and keep state.
Change _probe() to load firmware once fw_buf has been allocated.

s5p_mfc_open() and it continues to call s5p_mfc_load_firmware() and init
hardware which is the step where firmware is written to the device.

This addresses the mfc_mutex contention due to repeated request_firmware()
calls from open() in the following circular locking warning:

[  552.194115] qtdemux0:sink/2710 is trying to acquire lock:
[  552.199488]  (&dev->mfc_mutex){+.+.}, at: [<bf145544>] s5p_mfc_mmap+0x28/0xd4 [s5p_mfc]
[  552.207459]
               but task is already holding lock:
[  552.213264]  (&mm->mmap_sem){++++}, at: [<c01df2e4>] vm_mmap_pgoff+0x44/0xb8
[  552.220284]
               which lock already depends on the new lock.

[  552.228429]
               the existing dependency chain (in reverse order) is:
[  552.235881]
               -> #2 (&mm->mmap_sem){++++}:
[  552.241259]        __might_fault+0x80/0xb0
[  552.245331]        filldir64+0xc0/0x2f8
[  552.249144]        call_filldir+0xb0/0x14c
[  552.253214]        ext4_readdir+0x768/0x90c
[  552.257374]        iterate_dir+0x74/0x168
[  552.261360]        SyS_getdents64+0x7c/0x1a0
[  552.265608]        ret_fast_syscall+0x0/0x28
[  552.269850]
               -> #1 (&type->i_mutex_dir_key#2){++++}:
[  552.276180]        down_read+0x48/0x90
[  552.279904]        lookup_slow+0x74/0x178
[  552.283889]        walk_component+0x1a4/0x2e4
[  552.288222]        link_path_walk+0x174/0x4a0
[  552.292555]        path_openat+0x68/0x944
[  552.296541]        do_filp_open+0x60/0xc4
[  552.300528]        file_open_name+0xe4/0x114
[  552.304772]        filp_open+0x28/0x48
[  552.308499]        kernel_read_file_from_path+0x30/0x78
[  552.313700]        _request_firmware+0x3ec/0x78c
[  552.318291]        request_firmware+0x3c/0x54
[  552.322642]        s5p_mfc_load_firmware+0x54/0x150 [s5p_mfc]
[  552.328358]        s5p_mfc_open+0x4e4/0x550 [s5p_mfc]
[  552.333394]        v4l2_open+0xa0/0x104 [videodev]
[  552.338137]        chrdev_open+0xa4/0x18c
[  552.342121]        do_dentry_open+0x208/0x310
[  552.346454]        path_openat+0x28c/0x944
[  552.350526]        do_filp_open+0x60/0xc4
[  552.354512]        do_sys_open+0x118/0x1c8
[  552.358586]        ret_fast_syscall+0x0/0x28
[  552.362830]
               -> #0 (&dev->mfc_mutex){+.+.}:
               -> #0 (&dev->mfc_mutex){+.+.}:
[  552.368379]        lock_acquire+0x6c/0x88
[  552.372364]        __mutex_lock+0x68/0xa34
[  552.376437]        mutex_lock_interruptible_nested+0x1c/0x24
[  552.382086]        s5p_mfc_mmap+0x28/0xd4 [s5p_mfc]
[  552.386939]        v4l2_mmap+0x54/0x88 [videodev]
[  552.391601]        mmap_region+0x3a8/0x638
[  552.395673]        do_mmap+0x330/0x3a4
[  552.399400]        vm_mmap_pgoff+0x90/0xb8
[  552.403472]        SyS_mmap_pgoff+0x90/0xc0
[  552.407632]        ret_fast_syscall+0x0/0x28
[  552.411876]
               other info that might help us debug this:

[  552.419848] Chain exists of:
                 &dev->mfc_mutex --> &type->i_mutex_dir_key#2 --> &mm->mmap_sem

[  552.431200]  Possible unsafe locking scenario:

[  552.437092]        CPU0                    CPU1
[  552.441598]        ----                    ----
[  552.446104]   lock(&mm->mmap_sem);
[  552.449484]                                lock(&type->i_mutex_dir_key#2);
[  552.456329]                                lock(&mm->mmap_sem);
[  552.462222]   lock(&dev->mfc_mutex);
[  552.465775]
                *** DEADLOCK ***

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sfp: fix non-detection of PHY

[ Upstream commit 20b56ed9f8adfb9a7fb1c878878c54aa4ed645c1 ]

The detection of a PHY changed in commit e98a3aabf85f ("mdio_bus: don't
return NULL from mdiobus_scan()") which now causes sfp to print an
error message.  Update for this change.

Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sfp: fix EEPROM reading in the case of non-SFF8472 SFPs

[ Upstream commit 2794ffc441dde3109804085dc745e8014a4de224 ]

The EEPROM reading was trying to read from the second EEPROM address
if we requested the last byte from the SFF8079 EEPROM, which caused a
failure when the second EEPROM is not present.  Discovered with a
S-RJ01 SFP module.  Fix this.

Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: meson-gxl: check phy_write return value

[ Upstream commit 9042b46eda33ef5db3cdfc9e12b3c8cabb196141 ]

Always check phy_write return values. Better to be safe than sorry

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

/dev/mem: Add bounce buffer for copy-out

[ Upstream commit 22ec1a2aea73b9dfe340dff7945bd85af4cc6280 ]

As done for /proc/kcore in

  commit df04abfd181a ("fs/proc/kcore.c: Add bounce buffer for ktext data")

this adds a bounce buffer when reading memory via /dev/mem. This
is needed to allow kernel text memory to be read out when built with
CONFIG_HARDENED_USERCOPY (which refuses to read out kernel text) and
without CONFIG_STRICT_DEVMEM (which would have refused to read any RAM
contents at all).

Since this build configuration isn't common (most systems with
CONFIG_HARDENED_USERCOPY also have CONFIG_STRICT_DEVMEM), this also tries
to inform Kconfig about the recommended settings.

This patch is modified from Brad Spengler/PaX Team's changes to /dev/mem
code in the last public patch of grsecurity/PaX based on my understanding
of the code. Changes or omissions from the original code are mine and
don't reflect the original grsecurity/PaX code.

Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Fixes: f5509cc18daa ("mm: Hardened usercopy")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: block: fix logical error to avoid memory leak

[ Upstream commit 0be55579a127916ebe39db2a74d906a2dfceed42 ]

If the MMC_DRV_OP_GET_EXT_CSD request completes successfully, then
ext_csd must be freed, but in one case it was not. Fix that.

Signed-off-by: Liu Changcheng <changcheng.liu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: avoid removing non-removable hosts during suspend

[ Upstream commit de8dcc3d2c0e08e5068ee1e26fc46415c15e3637 ]

The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.

After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.

The conditions here are:

 1. During suspend, we reach mmc_pm_notify()

 2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
    suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
    -ENOSYS because btsdio_driver does not have a suspend method.

 3. mmc_pm_notify() proceeds to remove the card

 4. Upon resume, mmc_rescan() does nothing with this host, because of
    the rescan_entered check which aims to only scan a non-removable
    device a single time (i.e. during boot).

Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/tilcdc: ensure nonatomic iowrite64 is not used

[ Upstream commit 4e5ca2d930aa8714400aedf4bf1dc959cb04280f ]

Add a check to ensure iowrite64 is only used if it is atomic.

It was decided in [1] that the tilcdc driver should not be using an
atomic operation (so it was left out of this patchset). However, it turns
out that through the drm code, a nonatomic header is actually included:

include/linux/io-64-nonatomic-lo-hi.h
is included from include/drm/drm_os_linux.h:9:0,
            from include/drm/drmP.h:74,
            from include/drm/drm_modeset_helper.h:26,
            from include/drm/drm_atomic_helper.h:33,
            from drivers/gpu/drm/tilcdc/tilcdc_crtc.c:19:

And thus, without this change, this patchset would inadvertantly
change the behaviour of the tilcdc driver.

[1] lkml.kernel.org/r/CAK8P3a2HhO_zCnsTzq7hmWSz5La5Thu19FWZpun16iMnyyNreQ@mail.gmail.com

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: zynqmp_dma: Fix race condition in the probe

[ Upstream commit 5ba080aada5e739165e0f38d5cc3b04c82b323c8 ]

Incase of interrupt property is not present,
Driver is trying to free an invalid irq,
This patch fixes it by adding a check before freeing the irq.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/chrome: Use proper protocol transfer function

[ Upstream commit d48b8c58c57f6edbe2965f0a5f62c5cf9593ca96 ]

pkt_xfer should be used for protocol v3, and cmd_xfer otherwise. We had
one instance of these functions correct, but not the second, fall-back
case. We use the fall-back only when the first command returns an
IN_PROGRESS status, which is only used on some EC firmwares where we
don't want to constantly poll the bus, but instead back off and
sleep/retry for a little while.

Fixes: 2c7589af3c4d ("mfd: cros_ec: add proto v3 skeleton")
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: Fix kref imbalance seen if handle_boot_enabled=0

[ Upstream commit 914d65f3f013ba2556c7beec5d3baac7b3292504 ]

If handle_boot_enabled is set to 0, the watchdog driver module use
counter will not be increased and kref_get() will not be called when
registering the watchdog. Subsequently, on open, this does not happen
either because the code believes that it was already done because the
hardware watchdog is marked as running.

We could introduce a state variable to indicate this state, but let's
just increase the module use counter and call kref_get() unconditionally
if the hardware watchdog is running when a driver is registering itself
to keep the code simple.

Fixes: 2501b015313fe ("watchdog: core: add option to avoid early ...")
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: Fix potential kref imbalance when opening watchdog

[ Upstream commit 4bcd615fad6adddc68b058d498b30a9e0e0db77a ]

If a watchdog driver's open function sets WDOG_HW_RUNNING with the
expectation that the watchdog can not be stopped, but then stops the
watchdog anyway in its stop function, kref_get() wil not be called in
watchdog_open(). If the watchdog then stops on close, WDOG_HW_RUNNING
will be cleared and kref_put() will be called, causing a kref imbalance.
As result the character device data structure will be released, which in
turn will cause the system to crash on the next call to watchdog_open().

Fixes: ee142889e32f5 ("watchdog: Introduce WDOG_HW_RUNNING flag")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cros_ec: fix nul-termination for firmware build info

[ Upstream commit 50a0d71a5d20e1d3eff1d974fdc8559ad6d74892 ]

As gcc-8 reports, we zero out the wrong byte:

drivers/platform/chrome/cros_ec_sysfs.c: In function 'show_ec_version':
drivers/platform/chrome/cros_ec_sysfs.c:190:12: error: array subscript 4294967295 is above array bounds of 'uint8_t[]' [-Werror=array-bounds]

This changes the code back to what it did before changing to a
zero-length array structure.

Fixes: a841178445bb ("mfd: cros_ec: Use a zero-length array for command data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: Disable clock on error

[ Upstream commit 8af016aa5a27c6a2505460eb4d83f1e70c38dc43 ]

If there is no clock rate for uartclk defined, disable the previously
enabled clock again.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 23f5b3fdd04e serial: 8250_dw: only get the clock rate in one place
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: goldfish: Enable 'earlycon' only if built-in

[ Upstream commit 6a28fd2bbc94bfca105632e5ef8a9dbe63ba0b39 ]

Commit 3840ed9548f7 ("tty: goldfish: Implement support for kernel
'earlycon' parameter") breaks an allmodconfig config on x86:
|  LD      vmlinux.o
|  MODPOST vmlinux.o
|drivers/tty/serial/earlycon.o: In function `parse_options':
|drivers/tty/serial/earlycon.c:97: undefined reference to `uart_parse_earlycon'
|Makefile:1005: recipe for target 'vmlinux' failed

earlycon.c::parse_options() invokes uart_parse_earlycon() from serial_core.c
which is compiled=m because GOLDFISH_TTY itself (and most others) are =m.
To avoid that, I'm adding the _CONSOLE config option which is selected if the
GOLDFISH module itself is =y since it doesn't need the early bits for the =m
case (other drivers do the same dance).
The alternative would be to move uart_parse_earlycon() from
serial_core.c to earlycon.c (we don't have that many users of that
function).

Fixes: 3840ed9548f7 ("tty: goldfish: Implement support for kernel
       'earlycon' parameter")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Miodrag Dinic <miodrag.dinic@mips.com>
Acked-by: Miodrag Dinic <miodrag.dinic@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qmi_wwan: set FLAG_SEND_ZLP to avoid network initiated disconnect

[ Upstream commit 245d21190aec547c0de64f70c0e6de871c185a24 ]

It has been reported that the dummy byte we add to avoid
ZLPs can be forwarded by the modem to the PGW/GGSN, and that
some operators will drop the connection if this happens.

In theory, QMI devices are based on CDC ECM and should as such
both support ZLPs and silently ignore the dummy byte.  The latter
assumption failed.  Let's test out the first.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: [RESEND] media: dvb-frontends: Add delay to Si2168 restart

[ Upstream commit 380a6c86457573aa42d27ae11e025eb25941a0b7 ]

On faster CPUs a delay is required after the resume command and the restart command. Without the delay, the restart command often returns -EREMOTEIO and the Si2168 does not restart.

Note that this patch fixes the same issue as https://patchwork.linuxtv.org/patch/44304/, but I believe my udelay() fix addresses the actual problem.

Signed-off-by: Ron Economos <w6rz@comcast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: handling qos at STA side based on AP WMM enable/disable

[ Upstream commit 07ffb4497360ae8789f05555fec8171ee952304d ]

Data packets are not sent by STA in case of STA joined to
non QOS AP (WMM disabled AP). This is happening because of STA
is sending data packets to firmware from host with qos enabled
along with non qos queue value(TID = 16).
Due to qos enabled, firmware is discarding the packet.

This patch fixes this issue by updating the qos based on station
WME capability field if WMM is disabled in AP.

This patch is required by 10.4 family chipsets like
QCA4019/QCA9888/QCA9884/QCA99X0.
Firmware Versoin : 10.4-3.5.1-00018.

For 10.2.4 family chipsets QCA988X/QCA9887 and QCA6174 this patch
has no effect.

Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: bt8xx: Fix err 'bt878_probe()'

[ Upstream commit 45392ff6881dbe56d41ef0b17c2e576065f8ffa1 ]

This is odd to call 'pci_disable_device()' in an error path before a
coresponding successful 'pci_enable_device()'.

Return directly instead.

Fixes: 77e0be12100a ("V4L/DVB (4176): Bug-fix: Fix memory overflow")

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: always initialize variables given to RT_TRACE()

[ Upstream commit e4779162f7377baa9fb9a044555ecaae22c3f125 ]

In rtl_rx_ampdu_apply(), when rtlpriv->cfg->ops->get_btc_status()
returns false, RT_TRACE() is called with the values of variables
reject_agg and agg_size, which have not been initialized.

Always initialize these variables in order to prevent using
uninitialized values.

This issue has been found with clang. The compiler reported:

    drivers/net/wireless/realtek/rtlwifi/base.c:1665:6: error: variable
    'agg_size' is used uninitialized whenever 'if' condition is false
    [-Werror,-Wsometimes-uninitialized]
            if (rtlpriv->cfg->ops->get_btc_status())
                ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    drivers/net/wireless/realtek/rtlwifi/base.c:1671:31: note:
    uninitialized use occurs here
                     reject_agg, ctrl_agg_size, agg_size);
                                                ^~~~~~~~

    drivers/net/wireless/realtek/rtlwifi/base.c:1665:6: error: variable
    'reject_agg' is used uninitialized whenever 'if' condition
          is false [-Werror,-Wsometimes-uninitialized]
            if (rtlpriv->cfg->ops->get_btc_status())
                ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    drivers/net/wireless/realtek/rtlwifi/base.c:1671:4: note:
    uninitialized use occurs here
                     reject_agg, ctrl_agg_size, agg_size);
                     ^~~~~~~~~~

Fixes: 2635664e6e4a ("rtlwifi: Add rx ampdu cfg for btcoexist.")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl_pci: Fix the bug when inactiveps is enabled.

[ Upstream commit b7573a0a27bfa8270dea9b145448f6884b7cacc1 ]

Reset the driver current tx read/write index to zero when inactiveps
nic out of sync with HW state. Wrong driver tx read/write index will
cause Tx fail.

Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: sh-msiof: Avoid writing to registers from spi_setup()

[ Upstream commit 7ff0b53c4051145d1cf992d2f60987e6447eed4f ]

The spi_master.setup() callback must not change configuration registers,
as that could corrupt I/O that is in progress for other SPI slaves.

The only exception is the configuration of the native chip select
polarity in SPI master mode, as a wrong chip select polarity will cause
havoc during all future transfers to any other SPI slave.

Hence stop writing to registers in sh_msiof_spi_setup(), unless it is
the first call for a controller using a native chip select, or unless
native chip select polarity has changed (note that you'll loose anyway
if I/O is in progress).  Even then, only do what is strictly necessary,
instead of calling sh_msiof_spi_set_pin_regs().

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: Fix the TX/RX buffer default sizes

[ Upstream commit 41f61db2cd24d5ad802386719cccde1479aa82a6 ]

The values were not computed correctly. There are no significant
visible impact, though.

The intended size of RX buffer is 16 MB, and the default slot size is 1728.
So, NETVSC_DEFAULT_RX should be 16*1024*1024 / 1728 = 9709.

The intended size of TX buffer is 1 MB, and the slot size is 6144.
So, NETVSC_DEFAULT_TX should be 1024*1024 / 6144 = 170.

The patch puts the formula directly into the macro, and moves them to
hyperv_net.h, together with related macros.

Fixes: 5023a6db73196 ("netvsc: increase default receive buffer size")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: Fix the receive buffer size limit

[ Upstream commit 11b2b653102571ac791885324371d9a1a17b900e ]

The max should be 31 MB on host with NVSP version > 2.

On legacy hosts (NVSP version <=2) only 15 MB receive buffer is allowed,
otherwise the buffer request will be rejected by the host, resulting
vNIC not coming up.

The NVSP version is only available after negotiation. So, we add the
limit checking for legacy hosts in netvsc_init_buf().

Fixes: 5023a6db73196 ("netvsc: increase default receive buffer size")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/iwpm: Fix uninitialized error code in iwpm_send_mapinfo()

[ Upstream commit 302d6424e4a293a5761997e6c9fc3dfb1e4c355f ]

With gcc-4.1.2:

    drivers/infiniband/core/iwpm_util.c: In function ‘iwpm_send_mapinfo’:
    drivers/infiniband/core/iwpm_util.c:647: warning: ‘ret’ may be used uninitialized in this function

Indeed, if nl_client is not found in any of the scanned has buckets, ret
will be used uninitialized.

Preinitialize ret to -EINVAL to fix this.

Fixes: 30dc5e63d6a5ad24 ("RDMA/core: Add support for iWARP Port Mapper user space service")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/msm: fix leak in failed get_pages

[ Upstream commit 62e3a3e342af3c313ab38603811ecdb1fcc79edb ]

get_pages doesn't keep a reference of the pages allocated
when it fails later in the code path. This can lead to
a memory leak. Keep reference of the allocated pages so
that it can be freed when msm_gem_free_object gets called
later during cleanup.

Signed-off-by: Prakash Kamliya <pkamliya@codeaurora.org>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>