GitHub/exynos8895/android_kernel_samsung_universal8895.git
14 years agoi2c-intel-mid: Driver depends on PCI
Randy Dunlap [Fri, 29 Oct 2010 20:37:09 +0000 (13:37 -0700)]
i2c-intel-mid: Driver depends on PCI

i2c-intel-mid driver uses PCI data structs and interfaces,
so it should depend on PCI.  Fixes these build errors:

drivers/i2c/busses/i2c-intel-mid.c:977: error: implicit declaration of function 'pci_request_region'
drivers/i2c/busses/i2c-intel-mid.c:1077: error: implicit declaration of function 'pci_release_region'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ba Zheng <zheng.ba@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
14 years agoMerge branch 'for-2637/i2c/samsung' into next-i2c
Ben Dooks [Thu, 28 Oct 2010 09:07:14 +0000 (10:07 +0100)]
Merge branch 'for-2637/i2c/samsung' into next-i2c

14 years agoMerge branch 'for-2637/i2c/i2c-nomadik' into next-i2c
Ben Dooks [Thu, 28 Oct 2010 09:07:08 +0000 (10:07 +0100)]
Merge branch 'for-2637/i2c/i2c-nomadik' into next-i2c

14 years agoi2c-intel-mid: support for Moorestown and Medfield platform
Alan Cox [Wed, 27 Oct 2010 11:44:03 +0000 (12:44 +0100)]
i2c-intel-mid: support for Moorestown and Medfield platform

(Updated to address Ben's comments. With regard to the message segment
 restriction it's not something we hit on the actual platform so while
 I will investigate that further I don't think its a blocker to submission.
 At worst its a spot over-restrictive)

From: Wen Wang <wen.w.wang@intel.com>

Initial release of the driver. Updated and verified on hardware.

Cleaned up as follows

Alan Cox:
   Squash down the switches into tables, and use the PCI ident field. We
   could perhaps take this further and put the platform and port number into
   this.
   uint32t -> u32
   bracketing of case statements
   spacing and '!' usage
   Check the speed (which is now 0/1/2) is valid and ignore otherwise.
   Fix remaining problems/suggestions from Jean's review
   Fix items from Ben's review

Arjan van de Ven:
   Initial power management hooks

Yong Wang <youg.y.wang@intel.com>:
   Shared IRQ support

Wen Wang <wen.w.wang@intel.com>:
   D3 support
   Fixes for OCT test runs
   Interrupt optimisations

Hong Liu <hong.liu@intel.com>
   The runtime PM code is working on the wrong device (i2c_adapter->dev).
   The correct one should be pci_dev->dev. This breaks attached i2c
   slave devices with runtime PM enabled. Slave device needs to runtime
   resume parent device before runtime resuming itself, but we always get
   error since we don't have pm_runtime callback for i2c_adapter->dev.

Bin Yang <bin.yang@intel.com>:
   Update speed table

Saadi Maalem <saadi.maalem@intel.com>:
   Clear all interrupts in the hardware init

Celine Chotard <celinex.chotard@intel.com>:
   Correct ordering of clear/disable of IRQs

Signed-off-by: Wen Wang <wen.w.wang@intel.com>
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Bin Yang <bin.yang@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
14 years agoMerge branch 'for-next' of git://android.git.kernel.org/kernel/tegra
Linus Torvalds [Tue, 26 Oct 2010 01:42:06 +0000 (18:42 -0700)]
Merge branch 'for-next' of git://android.git./kernel/tegra

* 'for-next' of git://android.git.kernel.org/kernel/tegra:
  spi: tegra: fix error setting on timeout
  spi: add spi_tegra driver
  tegra: harmony: enable PCI Express
  tegra: add PCI Express support
  tegra: add PCI Express clocks
  [ARM] tegra: Add APB DMA support
  [ARM] tegra: Add cpufreq support
  [ARM] tegra: common: Update common clock init table
  [ARM] tegra: clock: Add dvfs support, bug fixes, and cleanups
  [ARM] tegra: Add support for reading fuses
  [ARM] tegra: gpio: Add suspend and wake support
  [ARM] tegra: pinmux: add safe values, move tegra2, add suspend
  [ARM] tegra: add suspend and mirror irqs to legacy controller
  [ARM] tegra: Add legacy irq support
  [ARM] tegra: update iomap

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier...
Linus Torvalds [Tue, 26 Oct 2010 01:41:32 +0000 (18:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/vapier/blackfin

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
  Blackfin: fix inverted anomaly 05000481 logic
  Blackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECK
  Blackfin: ppi/spi/twi headers: add missing __BFP undef
  Blackfin: update defconfigs
  Blackfin: bfin_twi.h: start a common TWI header
  netdev: bfin_mac: push settings to platform resources

14 years agospi: tegra: fix error setting on timeout
Erik Gilling [Thu, 9 Sep 2010 01:16:45 +0000 (18:16 -0700)]
spi: tegra: fix error setting on timeout

avoids derefencing an uninitialized pointer

Change-Id: Icf528441ae481e9f6f5ddc0be32c7c217fa49701
Signed-off-by: Erik Gilling <konkers@android.com>
14 years agoMerge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
Linus Torvalds [Mon, 25 Oct 2010 23:53:11 +0000 (16:53 -0700)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze

* 'next' of git://git.monstr.eu/linux-2.6-microblaze: (42 commits)
  microblaze: Fix build with make 3.82
  fbdev/xilinxfb: Microblaze driver support
  microblaze: Support C optimized lib functions for little-endian
  microblaze: Separate library optimized functions
  microblaze: Support timer on AXI lite
  microblaze: Add support for little-endian Microblaze
  microblaze: KGDB little endian support
  microblaze: Add PVR for endians plus detection
  net: emaclite: Add support for little-endian platforms
  microblaze: trivial: Add comment for AXI pvr
  microblaze: pci-common cleanup
  microblaze: Support early console on uart16550
  microblaze: Do not compile early console support for uartlite if is disabled
  microblaze: Setup early console dynamically
  microblaze: Rename all uartlite early printk functions
  microblaze: remove early printk uarlite console dependency from header
  microblaze: Remove additional compatible properties
  microblaze: Remove hardcoded asm instraction for PVR loading
  microblaze: Use static const char * const where possible
  microblaze: Define VMALLOC_START/END
  ...

14 years agoMerge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groec...
Linus Torvalds [Mon, 25 Oct 2010 23:25:31 +0000 (16:25 -0700)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
  hwmon: lis3: Release resources in case of failure
  hwmon: lis3: Short explanations of platform data fields
  hwmon: lis3: Enhance lis3 selftest with IRQ line test
  hwmon: lis3: use block read to access data registers
  hwmon: lis3: Adjust fuzziness for 8 bit device
  hwmon: lis3: New parameters to platform data
  hwmon: lis3: restore axis enabled bits
  hwmon: lis3: Power on corrections
  hwmon: lis3: Update coordinates at polled device open
  hwmon: lis3: Cleanup interrupt handling
  hwmon: lis3: regulator control
  hwmon: lis3: pm_runtime support
  Kirkwood: add fan support for Network Space Max v2
  hwmon: add generic GPIO fan driver
  hwmon: (coretemp) fix reading of microcode revision (v2)
  hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs
  hwmon: (pkgtemp) align driver initialization style with coretemp
  hwmon: LTC4261 Hardware monitoring driver
  hwmon: (lis3) add axes module parameter for custom axis-mapping
  hwmon: (hp_accel) Add HP Mini 510x family support
  ...

14 years agoMN10300: Fix the PERCPU() alignment to allow for workqueues
David Howells [Mon, 25 Oct 2010 22:41:11 +0000 (23:41 +0100)]
MN10300: Fix the PERCPU() alignment to allow for workqueues

In the MN10300 arch, we occasionally see an assertion being tripped in
alloc_cwqs() at the following line:

        /* just in case, make sure it's actually aligned */
  --->  BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align));
        return wq->cpu_wq.v ? 0 : -ENOMEM;

The values are:

        wa->cpu_wq.v => 0x902776e0
        align => 0x100

and align is calculated by the following:

        const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS,
                                   __alignof__(unsigned long long));

This is because the pointer in question (wq->cpu_wq.v) loses some of its
lower bits to control flags, and so the object it points to must be
sufficiently aligned to avoid the need to use those bits for pointing to
things.

Currently, 4 control bits and 4 colour bits are used in normal
circumstances, plus a debugging bit if debugging is set.  This requires
the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512
bytes aligned with debugging).

PERCPU() alignment on MN13000, however, is only 32 bytes as set in
vmlinux.lds.S.  So we set this to PAGE_SIZE (4096) to match most other
arches and stick a comment in alloc_cwqs() for anyone else who triggers
the assertion.

Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agohwmon: lis3: Release resources in case of failure
Samu Onkalo [Fri, 22 Oct 2010 11:57:34 +0000 (07:57 -0400)]
hwmon: lis3: Release resources in case of failure

If lis3lv02d_init_device fails, HW resources were not released
properly. In case of failure call release_resources if available.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agoBlackfin: fix inverted anomaly 05000481 logic
Mike Frysinger [Mon, 25 Oct 2010 08:49:49 +0000 (04:49 -0400)]
Blackfin: fix inverted anomaly 05000481 logic

No one uses these MMRs so we didn't notice when the anomaly handling
logic was inverted.

Reported-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
14 years agoBlackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECK
Mike Frysinger [Mon, 25 Oct 2010 21:22:49 +0000 (17:22 -0400)]
Blackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECK

This code was useful during early port development when our icache code
wasn't solid, but that ship has sailed long ago, and no code calls this
function anymore (irq_panic).  So punt it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
14 years agohwmon: lis3: Short explanations of platform data fields
Samu Onkalo [Sat, 23 Oct 2010 13:39:44 +0000 (09:39 -0400)]
hwmon: lis3: Short explanations of platform data fields

Short documentation at kernel doc format.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: Enhance lis3 selftest with IRQ line test
Samu Onkalo [Fri, 22 Oct 2010 11:57:32 +0000 (07:57 -0400)]
hwmon: lis3: Enhance lis3 selftest with IRQ line test

Configure chip to data ready mode in selftest and count received
interrupts to see that interrupt line(s) are working.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: use block read to access data registers
Samu Onkalo [Fri, 22 Oct 2010 11:57:31 +0000 (07:57 -0400)]
hwmon: lis3: use block read to access data registers

Add optional blockread function to interface driver. If available
the chip driver uses it for data register access. For 12 bit device
it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out
5 bytes since every second byte is dummy.
This optimizes bus usage and reduces number of operations and
interrupts needed for one data update.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: Adjust fuzziness for 8 bit device
Samu Onkalo [Fri, 22 Oct 2010 11:57:30 +0000 (07:57 -0400)]
hwmon: lis3: Adjust fuzziness for 8 bit device

Default fuziness is set smaller for 8 device.
In 12 bit device LSB is quite close to 1 mg
(mg = 1 / 1000 of earth gravity).
In 8bit device LSB is about 18 mg.
Set fuziness to 1 for 8 bit device.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: New parameters to platform data
Samu Onkalo [Fri, 22 Oct 2010 11:57:29 +0000 (07:57 -0400)]
hwmon: lis3: New parameters to platform data

Added default output data rate setting to platform data.
If default rate is 0, reset default value is used.
Added control for duration via platform data.
Added possibility to configure interrupts to trig on
both rising and falling edge. The lis3 WU unit can be
configured quite many ways and with some configurations it
is quite handy to get coordinate refresh when some
event trigs and when it reason goes away.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: restore axis enabled bits
Samu Onkalo [Fri, 22 Oct 2010 11:57:28 +0000 (07:57 -0400)]
hwmon: lis3: restore axis enabled bits

All axis enable bits are set to 0 at module remove.
Restore reset default value at init.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: Power on corrections
Samu Onkalo [Fri, 22 Oct 2010 11:57:27 +0000 (07:57 -0400)]
hwmon: lis3: Power on corrections

Sometimes lis3 chip seems to fail to setup factory tuning at boot up.
This probably happens if there is some odd power ramp down ramp up sequence
for example in device restart. Set boot bit in control2 register to
trig boot sequence manually and wait until it is finished.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: Update coordinates at polled device open
Samu Onkalo [Fri, 22 Oct 2010 11:57:26 +0000 (07:57 -0400)]
hwmon: lis3: Update coordinates at polled device open

Call input device poll function at device open to refresh coordinates
immediately. This is needed for the case where poll interval is set to
zero and coordinate updates happens purely under interrupt control.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: Cleanup interrupt handling
Samu Onkalo [Fri, 22 Oct 2010 11:57:25 +0000 (07:57 -0400)]
hwmon: lis3: Cleanup interrupt handling

Irqcfg moved to chip data instead of platform data.
This simplifies access in interrupt handler little bit.

Input device open and close functions set status for
interrupt threaded handler once.

Unnecessary check for interrupt source removed since
it is enough that active interrupt line indicates that
there was an interrupt.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: regulator control
Samu Onkalo [Fri, 22 Oct 2010 11:57:24 +0000 (07:57 -0400)]
hwmon: lis3: regulator control

Based on pm_runtime control, turn lis3 regulators on and off.
Perform context save and restore on transitions.

Feature is optional and must be enabled in platform data.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: lis3: pm_runtime support
Samu Onkalo [Fri, 22 Oct 2010 11:57:23 +0000 (07:57 -0400)]
hwmon: lis3: pm_runtime support

Add pm_runtime support to lis3 core driver.
Add pm_runtime support to lis3 i2c driver.

spi and hp_accel drivers are not yet supported. Old always
on functionality remains for those.

For sysfs there is 5 second delay before turning off the
chip to avoid long ramp up delay.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agoKirkwood: add fan support for Network Space Max v2
Simon Guinot [Fri, 22 Oct 2010 09:29:18 +0000 (05:29 -0400)]
Kirkwood: add fan support for Network Space Max v2

Signed-off-by: Simon Guinot <sguinot@lacie.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: add generic GPIO fan driver
Simon Guinot [Thu, 21 Oct 2010 22:44:19 +0000 (00:44 +0200)]
hwmon: add generic GPIO fan driver

This patch adds hwmon support for fans connected to GPIO lines.

Platform specific information such as GPIO pinout and speed conversion array
(rpm from/to GPIO value) are passed to the driver via platform_data.

Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: (coretemp) fix reading of microcode revision (v2)
Jan Beulich [Fri, 8 Oct 2010 08:59:38 +0000 (04:59 -0400)]
hwmon: (coretemp) fix reading of microcode revision (v2)

According to the documentation, simply reading the respective MSR
isn't sufficient: It should be written with zeros, cpuid(1) be
executed, and then read (see arch/x86/kernel/cpu/intel.c for an
example).

v2: Fail probe when microcode revision cannot be determined, but is
needed to check for proper operation.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs
Chen Gong [Sat, 9 Oct 2010 02:01:48 +0000 (22:01 -0400)]
hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs

CONFIG_HOTPLUG_CPU is used too much in some drivers.
This patch clean them up.

Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: (pkgtemp) align driver initialization style with coretemp
Chen Gong [Fri, 8 Oct 2010 05:53:35 +0000 (05:53 +0000)]
hwmon: (pkgtemp) align driver initialization style with coretemp

pkgtemp is derived from coretemp, so some reasonable
logics should be applied onto pkgtemp, too. Such as
the init logic here.

Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: LTC4261 Hardware monitoring driver
Guenter Roeck [Fri, 25 Jun 2010 18:59:54 +0000 (11:59 -0700)]
hwmon: LTC4261 Hardware monitoring driver

This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.

Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: (lis3) add axes module parameter for custom axis-mapping
Takashi Iwai [Fri, 1 Oct 2010 21:14:25 +0000 (17:14 -0400)]
hwmon: (lis3) add axes module parameter for custom axis-mapping

The axis-mapping of lis3dev device on many (rather most) HP machines
doesn't follow the standard.  When each new model appears, users need to
adjust again.  Testing this requires the rebuild of kernel, thus it's not
trivial for end-users.

This patch adds a module parameter "axes" to allow a custom axis-mapping
without patching and recompiling the kernel driver.  User can pass the
parameter such as axes=3,2,1.  Also it can be changed via sysfs.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: (hp_accel) Add HP Mini 510x family support
Masanari Iida [Fri, 27 Aug 2010 00:21:43 +0000 (00:21 +0000)]
hwmon: (hp_accel) Add HP Mini 510x family support

This patch is an enhanced version of Takashi Iwai's
[PATCH] hp_accel: Add quirks for HP ProBook 532x and HP Mini 5102
My HP Mini 5101 works fine with this patch.
Confirmed with Tux Racer.

Signed-off by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agohwmon: (lis3) Add support for new LIS3DC / HP3DC chip
Takashi Iwai [Thu, 23 Sep 2010 17:01:39 +0000 (10:01 -0700)]
hwmon: (lis3) Add support for new LIS3DC / HP3DC chip

A new version of LIS3 chip has slight incompatibilities from former
versions.  This patch adds the minimal support for it.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agox86/hwmon: remove inclusion of unnecessary headers from {core, pkg, via-cpu}temp.c
Jan Beulich [Mon, 13 Sep 2010 10:32:08 +0000 (10:32 +0000)]
x86/hwmon: remove inclusion of unnecessary headers from {core, pkg, via-cpu}temp.c

These likely originate from these drivers being clones of one another
and/or other drivers which actually needed these includes.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agox86/hwmon: (coretemp) cosmetic cleanup
Jan Beulich [Mon, 13 Sep 2010 10:28:35 +0000 (10:28 +0000)]
x86/hwmon: (coretemp) cosmetic cleanup

"break" after "return" is at best bogus (good compilers even warn about
the "break" being unreachable).

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agox86/hwmon: {core, pkg, via}cpu_temp_device_remove() can all be __cpuinit
Jan Beulich [Fri, 24 Sep 2010 05:31:10 +0000 (22:31 -0700)]
x86/hwmon: {core, pkg, via}cpu_temp_device_remove() can all be __cpuinit

... as they're being called only from a __cpuinit function.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
14 years agoMerge branch 'nfs-for-2.6.37' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
Linus Torvalds [Mon, 25 Oct 2010 20:48:29 +0000 (13:48 -0700)]
Merge branch 'nfs-for-2.6.37' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6

* 'nfs-for-2.6.37' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (67 commits)
  SUNRPC: Cleanup duplicate assignment in rpcauth_refreshcred
  nfs: fix unchecked value
  Ask for time_delta during fsinfo probe
  Revalidate caches on lock
  SUNRPC: After calling xprt_release(), we must restart from call_reserve
  NFSv4: Fix up the 'dircount' hint in encode_readdir
  NFSv4: Clean up nfs4_decode_dirent
  NFSv4: nfs4_decode_dirent must clear entry->fattr->valid
  NFSv4: Fix a regression in decode_getfattr
  NFSv4: Fix up decode_attr_filehandle() to handle the case of empty fh pointer
  NFS: Ensure we check all allocation return values in new readdir code
  NFS: Readdir plus in v4
  NFS: introduce generic decode_getattr function
  NFS: check xdr_decode for errors
  NFS: nfs_readdir_filler catch all errors
  NFS: readdir with vmapped pages
  NFS: remove page size checking code
  NFS: decode_dirent should use an xdr_stream
  SUNRPC: Add a helper function xdr_inline_peek
  NFS: remove readdir plus limit
  ...

14 years agoMerge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind...
Linus Torvalds [Mon, 25 Oct 2010 20:46:56 +0000 (13:46 -0700)]
Merge branch 'omap-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
  omap: complete removal of machine_desc.io_pg_offst and .phys_io
  omap: UART: fix wakeup registers for OMAP24xx UART2
  omap: Fix spotty MMC voltages
  ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
  serial: omap-serial: fix signess error
  OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
  omap: dma: Fix buffering disable bit setting for omap24xx
  omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
  OMAP3: PM: fix scratchpad memory accesses for off-mode
  omap4: pandaboard: enable the ehci port on pandaboard
  omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
  omap4: pandaboard: remove unused hsmmc definition
  OMAP: McBSP: Remove null omap44xx ops comment
  OMAP: McBSP: Swap CLKS source definition
  OMAP: McBSP: Fix CLKR and FSR signal muxing
  OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
  OMAP: control: move plat-omap/control.h to mach-omap2/control.h
  OMAP: split plat-omap/common.c
  OMAP: McBSP: implement functional clock switching via clock framework
  OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
  ...

Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony

14 years agoMerge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Mon, 25 Oct 2010 17:59:31 +0000 (10:59 -0700)]
Merge branch 'davinci-for-linus' of git://git./linux/kernel/git/khilman/linux-davinci

* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
  davinci: fix remaining board support after io_pgoffst removal
  davinci: mityomapl138: make file local data static
  arm/davinci: remove duplicated include
  davinci: Initial support for Omapl138-Hawkboard
  davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
  davinci: add tnetv107x touchscreen platform device
  input: add driver for tnetv107x touchscreen controller
  davinci: add keypad config for tnetv107x evm board
  davinci: add tnetv107x keypad platform device
  input: add driver for tnetv107x on-chip keypad controller
  net: davinci_emac: cleanup unused cpdma code
  net: davinci_emac: switch to new cpdma layer
  net: davinci_emac: separate out cpdma code
  net: davinci_emac: cleanup unused mdio emac code
  omap: cleanup unused davinci mdio arch code
  davinci: cleanup mdio arch code and switch to phy_id
  net: davinci_emac: switch to new mdio
  omap: add mdio platform devices
  davinci: add mdio platform devices
  net: davinci_emac: separate out davinci mdio
  ...

Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)

14 years agoMerge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
Linus Torvalds [Mon, 25 Oct 2010 17:08:21 +0000 (10:08 -0700)]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd

* 'for-linus' of git://git.open-osd.org/linux-open-osd:
  exofs: Remove inode->i_count manipulation in exofs_new_inode
  fs/exofs: typo fix of faild to failed
  exofs: Set i_mapping->backing_dev_info anyway
  exofs: Cleaup read path in regard with read_for_write

14 years agox86-32, mm: Remove duplicated include
Borislav Petkov [Mon, 25 Oct 2010 16:15:22 +0000 (18:15 +0200)]
x86-32, mm: Remove duplicated include

Commit b40827fa7268 ("x86-32, mm: Add an initial page table for core
bootstrapping") added an include directive which is needless and is
taken care of by a previous one.  Remove it.

Caught-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoexofs: Remove inode->i_count manipulation in exofs_new_inode
Boaz Harrosh [Sat, 16 Oct 2010 08:14:01 +0000 (19:14 +1100)]
exofs: Remove inode->i_count manipulation in exofs_new_inode

exofs_new_inode() was incrementing the inode->i_count and
decrementing it in create_done(), in a bad attempt to make sure
the inode will still be there when the asynchronous create_done()
finally arrives. This was very stupid because iput() was not called,
and if it was actually needed, it would leak the inode.

However all this is not needed, because at exofs_evict_inode()
we already wait for create_done() by waiting for the
object_created event. Therefore remove the superfluous ref counting
and just Thicken the comment at exofs_evict_inode() a bit.

While at it change places that open coded wait_obj_created()
to call the already available wrapper.

CC: Dave Chinner <dchinner@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
14 years agofs/exofs: typo fix of faild to failed
Joe Perches [Fri, 22 Oct 2010 05:17:17 +0000 (22:17 -0700)]
fs/exofs: typo fix of faild to failed

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
14 years agoMerge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
Linus Torvalds [Mon, 25 Oct 2010 15:36:50 +0000 (08:36 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (48 commits)
  [S390] topology: export cpu topology via proc/sysinfo
  [S390] topology: move topology sysinfo code
  [S390] topology: clean up facility detection
  [S390] cleanup facility list handling
  [S390] enable ARCH_DMA_ADDR_T_64BIT with 64BIT
  [S390] dasd: ignore unsolicited interrupts for DIAG
  [S390] kvm: Enable z196 instruction facilities
  [S390] dasd: fix unsolicited interrupt recognition
  [S390] dasd: fix use after free in dbf
  [S390] kvm: Fix badness at include/asm/mmu_context.h:83
  [S390] cio: fix I/O cancel function
  [S390] topology: change default
  [S390] smp: use correct cpu address in print_cpu_info()
  [S390] remove ieee_instruction_pointer from thread_struct
  [S390] cleanup system call parameter setup
  [S390] correct alignment of cpuid structure
  [S390] cleanup lowcore access from external interrupts
  [S390] cleanup lowcore access from program checks
  [S390] pgtable: move pte_mkhuge() from hugetlb.h to pgtable.h
  [S390] fix SIGBUS handling
  ...

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Mon, 25 Oct 2010 15:32:05 +0000 (08:32 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
  ALSA: hda - Disable sticky PCM stream assignment for AD codecs
  ALSA: usb - Creative USB X-Fi volume knob support
  ALSA: ca0106: Use card specific dac id for mute controls.
  ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
  ALSA: ca0106: Create a nice spot for mapping channels to dacs.
  ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
  ALSA: ca0106: Pull out dac powering routine into separate function.
  ALSA: ca0106 - add Sound Blaster 5.1vx info.
  ASoC: tlv320dac33: Use usleep_range for delays
  ALSA: usb-audio: add Novation Launchpad support
  ALSA: hda - Add workarounds for CT-IBG controllers
  ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
  ASoC: tpa6130a2: Error handling for broken chip
  ASoC: max98088: Staticise m98088_eq_band
  ASoC: soc-core: Fix codec->name memory leak
  ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
  ALSA: hda - Add some workarounds for Creative IBG
  ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
  ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
  ALSA: hda - Add alc_init_jacks() call to other codecs
  ...

14 years agoMerge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb
Linus Torvalds [Mon, 25 Oct 2010 15:30:48 +0000 (08:30 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/dvrabel/uwb

* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
  uwb: Orphan the UWB and WUSB subsystems
  uwb: Remove the WLP subsystem and drivers

14 years agoMerge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platf...
Linus Torvalds [Mon, 25 Oct 2010 15:28:13 +0000 (08:28 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mjg59/platform-drivers-x86

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (44 commits)
  eeepc-wmi: Add cpufv sysfs interface
  eeepc-wmi: add additional hotkeys
  panasonic-laptop: Simplify calls to acpi_pcc_retrieve_biosdata
  panasonic-laptop: Handle errors properly if they happen
  intel_pmic_gpio: fix off-by-one value range checking
  IBM Real-Time "SMI Free" mode driver -v7
  Add OLPC XO-1 rfkill driver
  Move hdaps driver to platform/x86
  ideapad-laptop: Fix Makefile
  intel_pmic_gpio: swap the bits and mask args for intel_scu_ipc_update_register
  ideapad: Add param: no_bt_rfkill
  ideapad: Change the driver name to ideapad-laptop
  ideapad: rewrite the sw rfkill set
  ideapad: rewrite the hw rfkill notify
  ideapad: use EC command to control camera
  ideapad: use return value of _CFG to tell if device exist or not
  ideapad: make sure we bind on the correct device
  ideapad: check VPC bit before sync rfkill hw status
  ideapad: add ACPI helpers
  dell-laptop: Add debugfs support
  ...

14 years agoMerge branch 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6
Linus Torvalds [Mon, 25 Oct 2010 15:19:14 +0000 (08:19 -0700)]
Merge branch 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6

* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
  mtd/m25p80: add support to parse the partitions by OF node
  of/irq: of_irq.c needs to include linux/irq.h
  of/mips: Cleanup some include directives/files.
  of/mips: Add device tree support to MIPS
  of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
  of/device: Rework to use common platform_device_alloc() for allocating devices
  of/xsysace: Fix OF probing on little-endian systems
  of: use __be32 types for big-endian device tree data
  of/irq: remove references to NO_IRQ in drivers/of/platform.c
  of/promtree: add package-to-path support to pdt
  of/promtree: add of_pdt namespace to pdt code
  of/promtree: no longer call prom_ functions directly; use an ops structure
  of/promtree: make drivers/of/pdt.c no longer sparc-only
  sparc: break out some PROM device-tree building code out into drivers/of
  of/sparc: convert various prom_* functions to use phandle
  sparc: stop exporting openprom.h header
  powerpc, of_serial: Endianness issues setting up the serial ports
  of: MTD: Fix OF probing on little-endian systems
  of: GPIO: Fix OF probing on little-endian systems

14 years agoMIPS: MT: Fix build error iFPU affinity code
Ralf Baechle [Sun, 24 Oct 2010 21:23:50 +0000 (22:23 +0100)]
MIPS: MT: Fix build error iFPU affinity code

Commit b0ae19811375 ("security: remove unused parameter from
security_task_setscheduler()") broke the build of
arch/mips/kernel/mips-mt-fpaff.c.  The function arguments were
unnecessary, not the semicolon ...

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoMerge branch 'ieee1394-removal' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Mon, 25 Oct 2010 15:05:29 +0000 (08:05 -0700)]
Merge branch 'ieee1394-removal' of git://git./linux/kernel/git/ieee1394/linux1394-2.6

* 'ieee1394-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  ieee1394: remove the old IEEE 1394 driver stack
  ieee1394: move init_ohci1394_dma to drivers/firewire/

Fix trivial change/delete conflict: drivers/ieee1394/eth1394.c is
getting removed, but was modified by the networking merge.

14 years agoCoda: replace BKL with mutex
Yoshihisa Abe [Mon, 25 Oct 2010 06:03:46 +0000 (02:03 -0400)]
Coda: replace BKL with mutex

Replace the BKL with a mutex to protect the venus_comm structure which
binds the mountpoint with the character device and holds the upcall
queues.

Signed-off-by: Yoshihisa Abe <yoshiabe@cs.cmu.edu>
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoCoda: push BKL regions into coda_upcall()
Yoshihisa Abe [Mon, 25 Oct 2010 06:03:45 +0000 (02:03 -0400)]
Coda: push BKL regions into coda_upcall()

Now that shared inode state is locked using the cii->c_lock, the BKL is
only used to protect the upcall queues used to communicate with the
userspace cache manager. The remaining state is all local and we can
push the lock further down into coda_upcall().

Signed-off-by: Yoshihisa Abe <yoshiabe@cs.cmu.edu>
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoCoda: add spin lock to protect accesses to struct coda_inode_info.
Yoshihisa Abe [Mon, 25 Oct 2010 06:03:44 +0000 (02:03 -0400)]
Coda: add spin lock to protect accesses to struct coda_inode_info.

We mostly need it to protect cached user permissions. The c_flags field
is advisory, reading the wrong value is harmless and in the worst case
we hit a slow path where we have to make an extra upcall to the
userspace cache manager when revalidating a dentry or inode.

Signed-off-by: Yoshihisa Abe <yoshiabe@cs.cmu.edu>
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Linus Torvalds [Mon, 25 Oct 2010 14:59:01 +0000 (07:59 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (75 commits)
  Input: wacom - specify Cinitq supported tools
  Input: ab8500-ponkey - fix IRQ freeing in error path
  Input: adp5588-keys - use more obvious i2c_device_id name string
  Input: ad7877 - switch to using threaded IRQ
  Input: ad7877 - use attribute group to control visibility of attributes
  Input: serio - add support for PS2Mult multiplexer protocol
  Input: wacom - properly enable runtime PM
  Input: ad7877 - filter events where pressure is beyond the maximum
  Input: ad7877 - implement EV_KEY:BTN_TOUCH reporting
  Input: ad7877 - implement specified chip select behavior
  Input: hp680_ts_input - use cancel_delayed_work_sync()
  Input: mousedev - correct lockdep annotation
  Input: ads7846 - switch to using threaded IRQ
  Input: serio - support multiple child devices per single parent
  Input: synaptics - simplify pass-through port handling
  Input: add ROHM BU21013 touch panel controller support
  Input: omap4-keypad - wake-up on events & long presses
  Input: omap4-keypad - fix interrupt line configuration
  Input: omap4-keypad - SYSCONFIG register configuration
  Input: omap4-keypad - use platform device helpers
  ...

14 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
Linus Torvalds [Mon, 25 Oct 2010 14:51:49 +0000 (07:51 -0700)]
Merge git://git./linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
  sh: i2c-sh7760: Replase from ctrl_* to __raw_*
  sh: clkfwk: Shuffle around to match the intc split up.
  sh: clkfwk: modify for_each_frequency end condition
  sh: fix clk_get() error handling
  sh: clkfwk: Fix fault in frequency iterator.
  sh: clkfwk: Add a helper for rate rounding by divisor ranges.
  sh: clkfwk: Abstract rate rounding helper.
  sh: clkfwk: support clock remapping.
  sh: pci: Convert to upper/lower_32_bits() helpers.
  sh: mach-sdk7786: Add support for the FPGA SRAM.
  sh: Provide a generic SRAM pool for tiny memories.
  sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
  sh: pci: Support slot 4 routing on SDK7786.
  sh: Fix up PMB locking.
  sh: mach-sdk7786: Add support for fpga gpios.
  sh: use pr_fmt for clock framework, too.
  sh: remove name and id from struct clk
  sh: free-without-alloc fix for sh_mobile_lcdcfb
  sh: perf: Set up perf_max_events.
  sh: perf: Support SH-X3 hardware counters.
  ...

Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c

14 years agoMerge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
Linus Torvalds [Mon, 25 Oct 2010 14:45:10 +0000 (07:45 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Revert "block: fix accounting bug on cross partition merges"

14 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Linus Torvalds [Mon, 25 Oct 2010 14:44:27 +0000 (07:44 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/gerg/m68knommu

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
  m68knommu: convert to using tracehook_report_syscall_*
  m68knommu: some boards use fixed phy for FEC ethernet
  m68knommu: support the external GPIO based interrupts of the 5272
  m68knommu: mask of vector bits in exception word properly
  m68knommu: change to new flag variables
  m68knommu: Fix MCFUART_TXFIFOSIZE for m548x.
  m68knommu: add basic mmu-less m548x support
  m68knommu: .gitignore vmlinux.lds
  m68knommu: stop using __do_IRQ
  m68knommu: rename PT_OFF_VECTOR to PT_OFF_FORMATVEC.
  m68knommu: add support for Coldfire 547x/548x interrupt controller
  m68k{nommu}: Remove unused DEFINE's from asm-offsets.c
  m68knommu: whitespace cleanup in 68328/entry.S
  m68knommu: Document supported chips in intc-2.c and intc-simr.c.
  m68knommu: fix strace support for 68328/68360
  m68knommu: fix default starting date
  arch/m68knommu: Removing dead 68328_SERIAL_UART2 config option
  arch/m68knommu: Removing dead RAM_{16,32}_MB config option
  arch/m68knommu: Removing dead M68KFPU_EMU config option
  arch/m68knommu: Removing dead RELOCATE config option
  ...

14 years ago[S390] topology: export cpu topology via proc/sysinfo
Heiko Carstens [Mon, 25 Oct 2010 14:10:54 +0000 (16:10 +0200)]
[S390] topology: export cpu topology via proc/sysinfo

Export the cpu configuration topology via sysinfo. Two new lines are
introduced:

CPU Topology HW:      0 0 0 4 6 4
CPU Topology SW:      0 0 0 0 4 24

The HW line describes the cpu topology nesting levels when the maximum
nesting level is used to get the corresponding SYSIB.
The SW line describes what Linux is actually using. In this case it
supports only two levels (CONFIG_SCHED_BOOK off) and therefore the
hardware folded the two lower levels in the SYSIB response block.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] topology: move topology sysinfo code
Heiko Carstens [Mon, 25 Oct 2010 14:10:53 +0000 (16:10 +0200)]
[S390] topology: move topology sysinfo code

Move the topology sysinfo SYSIB definitions to the proper place in
asm/sysinfo.h where they should be.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] topology: clean up facility detection
Heiko Carstens [Mon, 25 Oct 2010 14:10:52 +0000 (16:10 +0200)]
[S390] topology: clean up facility detection

Move cpu topology facility detection to early setup code where it
should be.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cleanup facility list handling
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:51 +0000 (16:10 +0200)]
[S390] cleanup facility list handling

Store the facility list once at system startup with stfl/stfle and
reuse the result for all facility tests.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] enable ARCH_DMA_ADDR_T_64BIT with 64BIT
FUJITA Tomonori [Mon, 25 Oct 2010 14:10:50 +0000 (16:10 +0200)]
[S390] enable ARCH_DMA_ADDR_T_64BIT with 64BIT

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] dasd: ignore unsolicited interrupts for DIAG
Stefan Haberland [Mon, 25 Oct 2010 14:10:49 +0000 (16:10 +0200)]
[S390] dasd: ignore unsolicited interrupts for DIAG

For the DASD DIAG discipline IO is started through special diagnose
calls. Unsolicited interrupts may contain information about the device
itself. But this information is not needed because the device is not
used directly.
Fix the case that an unimplemented dicipline function may be called
by ignoring unsolicited interrupts for the DIAG disciplin.

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] kvm: Enable z196 instruction facilities
Christian Borntraeger [Mon, 25 Oct 2010 14:10:48 +0000 (16:10 +0200)]
[S390] kvm: Enable z196 instruction facilities

Enable PFPO, floating point extension, distinct-operands,
fast-BCR-serialization, high-word, interlocked-access, load/store-
on-condition, and population-count facilities for guests.
(bits 37, 44 and 45).

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] dasd: fix unsolicited interrupt recognition
Stefan Weinhuber [Mon, 25 Oct 2010 14:10:47 +0000 (16:10 +0200)]
[S390] dasd: fix unsolicited interrupt recognition

The dasd interrupt handler needs to distinguish solicited from
unsolicited interrupts, as unsolicited interrupts may require special
handling (e.g. summary unit checks) and solicited interrupts require
proper error recovery for the failed I/O request.
The interrupt handler needs to check several bit fields in the
interrupt response block (irb) to make this distinction.
So far our check of the status control bits has not been specific
enough, which may lead to a failed request getting just retried
instead of the necessary error recovery.

Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] dasd: fix use after free in dbf
Sebastian Ott [Mon, 25 Oct 2010 14:10:46 +0000 (16:10 +0200)]
[S390] dasd: fix use after free in dbf

Writing to /proc/dasd/statistics while the debug level of the
generic dasd debug entry is set to DBF_DEBUG will lead to an
use after free when accessing the debug entry later.
Since for the format string "%s" in the s390 dbf only a pointer
to the string is stored in the debug feature and the buffer used
here is freed afterwards.

To fix this just remove the debug message.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] kvm: Fix badness at include/asm/mmu_context.h:83
Christian Borntraeger [Mon, 25 Oct 2010 14:10:45 +0000 (16:10 +0200)]
[S390] kvm: Fix badness at include/asm/mmu_context.h:83

commit 050eef364ad700590a605a0749f825cab4834b1e
    [S390] fix tlb flushing vs. concurrent /proc accesses
broke KVM on s390x. On every schedule a
Badness at include/asm/mmu_context.h:83 appears. s390_enable_sie
replaces the mm on the __running__ task, therefore, we have to
increase the attach count of the new mm.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cio: fix I/O cancel function
Peter Oberparleiter [Mon, 25 Oct 2010 14:10:44 +0000 (16:10 +0200)]
[S390] cio: fix I/O cancel function

Function ccw_device_cancel_halt_clear may cause an unexpected kernel
panic if a clear function is currently active at the subchannel for
which it is called. In that case, the iretry counter used to determine
the number of retries is never initialized, leading to an immediate
failure of the function which results in a kernel panic.

Fix this by initializing the iretry counter when the function is
first called. Also replace the kernel panic with a return code: a
single malfunctioning I/O device should not automatically cause a
system-wide kernel panic.

Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] topology: change default
Heiko Carstens [Mon, 25 Oct 2010 14:10:43 +0000 (16:10 +0200)]
[S390] topology: change default

Switch default value of the kernel parameter 'topology' from off to on.
Various performance measurements have finally shown that there are no
(known) regressions anywhere.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] smp: use correct cpu address in print_cpu_info()
Heiko Carstens [Mon, 25 Oct 2010 14:10:42 +0000 (16:10 +0200)]
[S390] smp: use correct cpu address in print_cpu_info()

Up to now print_cpu_info() uses the cpu address stored in it's local
lowcore to print a message to the console. The cpu address in the
lowcore is (in this case) however not the physical cpu address of the
local cpu. It's the address of the cpu that issued the sigp restart
which started the local cpu.
Fix this by using the store cpu address instruction instead.
It's not that anybody really cares since this is broken since more than
ten years...

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] remove ieee_instruction_pointer from thread_struct
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:41 +0000 (16:10 +0200)]
[S390] remove ieee_instruction_pointer from thread_struct

The ieee_instruction_pointer can not be read from user space anymore
since git commit 613e1def6b52c399a8b72a5e11bc2e57d2546fb8, the ptrace
interface always returns zero. Remove it from the thread_struct. It
is still present in the user_regs_struct for compatability reasons.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cleanup system call parameter setup
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:40 +0000 (16:10 +0200)]
[S390] cleanup system call parameter setup

Do the setup of the stack overflow argument for the sixth system
call parameter right before the branch to the system call function.
That simplifies the system call parameter access code.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] correct alignment of cpuid structure
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:39 +0000 (16:10 +0200)]
[S390] correct alignment of cpuid structure

The store-cpu-id instruction has a minimum alignment of 8. Reflect
that in the definition of struct cpuid.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cleanup lowcore access from external interrupts
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:38 +0000 (16:10 +0200)]
[S390] cleanup lowcore access from external interrupts

Read external interrupts parameters from the lowcore in the first
level interrupt handler in entry[64].S.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cleanup lowcore access from program checks
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:37 +0000 (16:10 +0200)]
[S390] cleanup lowcore access from program checks

Read all required fields for program checks from the lowcore in the
first level interrupt handler in entry[64].S. If the context that
caused the fault was enabled for interrupts we can now re-enable the
irqs in entry[64].S.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] pgtable: move pte_mkhuge() from hugetlb.h to pgtable.h
Heiko Carstens [Mon, 25 Oct 2010 14:10:36 +0000 (16:10 +0200)]
[S390] pgtable: move pte_mkhuge() from hugetlb.h to pgtable.h

All architectures besides s390 have pte_mkhuge() defined in pgtable.h.
So move the function to pgtable.h on s390 as well.
Fixes a compile error introduced with "hugetlb: hugepage migration core"
in linux-next which only happens on s390.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] fix SIGBUS handling
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:35 +0000 (16:10 +0200)]
[S390] fix SIGBUS handling

Raise SIGBUS with a siginfo structure. Deliver BUS_ADRERR as si_code and
the address of the fault in the si_addr field.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cio: notify drivers of channel path events
Sebastian Ott [Mon, 25 Oct 2010 14:10:34 +0000 (16:10 +0200)]
[S390] cio: notify drivers of channel path events

This patch adds a notification mechanism to inform ccw drivers
about changes to channel paths, which occured while the device
is online.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] css: update subchannel description after hibernate
Sebastian Ott [Mon, 25 Oct 2010 14:10:33 +0000 (16:10 +0200)]
[S390] css: update subchannel description after hibernate

Update the subchannel descriptor while resuming from hibernate
in order to obtain current link addresses.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] css: update descriptor after hibernate
Sebastian Ott [Mon, 25 Oct 2010 14:10:32 +0000 (16:10 +0200)]
[S390] css: update descriptor after hibernate

Update the channel path descriptors after hibernation.
This is done unlocked, since we are the only active
task at this time.

Note: chsc_determine_base_channel_path_desc is changed
to use spin_lock_irqsave, since it's called with
interrupts disabled in this case.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cio: update descriptor in chsc_chp_vary
Sebastian Ott [Mon, 25 Oct 2010 14:10:31 +0000 (16:10 +0200)]
[S390] cio: update descriptor in chsc_chp_vary

Update the channel path descriptor at the beginning of to the
vary_on operation.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] chsc: use the global page to determine the chp desriptor
Sebastian Ott [Mon, 25 Oct 2010 14:10:30 +0000 (16:10 +0200)]
[S390] chsc: use the global page to determine the chp desriptor

chsc_determine_channel_path_desc is called by a wrapper
who allocates a response struct. The response data
is then memcpy'ed to this response struct by
chsc_determine_channel_path_desc.

Change chsc_determine_base_channel_path_desc to use the
global chsc_page and deliver it to the function doing
the actual chsc call. The channel path desriptor is
then directly read from the response data.

As a result we get rid of the additional allocation
for the response struct.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] chsc: consolidate memory allocations
Sebastian Ott [Mon, 25 Oct 2010 14:10:29 +0000 (16:10 +0200)]
[S390] chsc: consolidate memory allocations

Most wrappers around the channel subsystem call have their own logic
to allocate memory (with proper alignment) or use preallocated or
static memory. This patch converts most users of the channel
subsystem call to use the same preallocated page (proteced by a
spinlock).

Note: The sei_page which is used in our crw handler to call
"store event information" has to coexist, since
a) in crw context, while accessing the sei_page, sleeping is allowed
   (which will conflict with the spinlock protection of the chsc_page)
b) in crw context, while accessing the sei_page, channel subsystem
   calls are allowed (which itself would require the page).

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] chsc: initialization fixes
Sebastian Ott [Mon, 25 Oct 2010 14:10:28 +0000 (16:10 +0200)]
[S390] chsc: initialization fixes

This patch fixes:
 * kfree vs. free_page usage
 * structure definition for determine_css_characteristics
 * naming convention for the chsc init function
 * deregistration of crw handlers in the cleanup path

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cio: add lock to struct channel_path
Sebastian Ott [Mon, 25 Oct 2010 14:10:27 +0000 (16:10 +0200)]
[S390] cio: add lock to struct channel_path

Serialize access to members of struct channel_path with a mutex.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cio: fix memleak in resume path
Sebastian Ott [Mon, 25 Oct 2010 14:10:26 +0000 (16:10 +0200)]
[S390] cio: fix memleak in resume path

If a ccwdevice is lost during hibernation and a different
ccwdevice is attached to the same subchannel, we will
deregister the old ccw device and register the new one.

Since deregistration is not allowed in this context, we
handle this action later. However, some parts of the
registration process for the new device were started anyway,
so that the old device structure is no longer accessible.

Fix this by deferring both actions to the afterwards
scheduled subchannel event.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cio: remove custom implementation of hex_to_bin()
Andy Shevchenko [Mon, 25 Oct 2010 14:10:25 +0000 (16:10 +0200)]
[S390] cio: remove custom implementation of hex_to_bin()

Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] dasd fix dump_sense_dbf
Stefan Haberland [Mon, 25 Oct 2010 14:10:24 +0000 (16:10 +0200)]
[S390] dasd fix dump_sense_dbf

The dasd_eckd_dump_sense_dbf function uses a macro for s390 debug
feature that can handle up to 8 parameters (for the DASD device
driver).
Fix the function to use only the maximum number of parameters.

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] css: fix sparse warning
Sebastian Ott [Mon, 25 Oct 2010 14:10:23 +0000 (16:10 +0200)]
[S390] css: fix sparse warning

fix this sparse warning:

drivers/s390/cio/css.c:580:6: warning: symbol 'css_schedule_eval_all_unreg'
was not declared. Should it be static?

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] hvc_iucv: do not call iucv_unregister if iucv_register failed
Hendrik Brueckner [Mon, 25 Oct 2010 14:10:22 +0000 (16:10 +0200)]
[S390] hvc_iucv: do not call iucv_unregister if iucv_register failed

If the iucv_register() functions fails, the error recovery calls
iucv_unregister() which might cause the following stack backtrace:

(<0000000000100ab2> show_trace+0xee/0x144)
<00000000004f1842> panic+0xb6/0x248
<00000000001010a6> die+0x15a/0x16c
<000000000011d936> do_no_context+0xa6/0xe4
<00000000004f84dc> do_protection_exception+0x2e8/0x3a4
<0000000000113afc> pgm_exit+0x0/0x14
<00000000004e786e> iucv_unregister+0x5a/0x17c
(<00000000004e785e> iucv_unregister+0x4a/0x17c)
<000000000076de74> hvc_iucv_init+0x228/0x5dc
<00000000001000c2> do_one_initcall+0x3e/0x19c
<00000000007524a2> kernel_init+0x28e/0x404
<0000000000105dd6> kernel_thread_starter+0x6/0xc
<0000000000105dd0> kernel_thread_starter+0x0/0xc

Remove the call to iucv_unregister() and remove the goto label
as unregistering is the last step in the hvc_iucv initialization.
If iucv_register() fails, simply clean up hvc terminals and free
resources.

Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cmm: fix crash on case conversion
Heiko Carstens [Mon, 25 Oct 2010 14:10:21 +0000 (16:10 +0200)]
[S390] cmm: fix crash on case conversion

When the cmm module is compiled into the kernel it will crash when
writing to the R/O data section.
Reason is the lower to upper case conversion of the "sender" module
parameter which ignored the fact that the pointer is preinitialized.

Introduced with 41b42876 "cmm, smsgiucv_app: convert sender to
uppercase"

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] drivers/s390/char: Use static const char arrays
Joe Perches [Mon, 25 Oct 2010 14:10:20 +0000 (16:10 +0200)]
[S390] drivers/s390/char: Use static const char arrays

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] switch_to: get rid of prev == next check
Heiko Carstens [Mon, 25 Oct 2010 14:10:19 +0000 (16:10 +0200)]
[S390] switch_to: get rid of prev == next check

schedule() makes sure that prev != next before calling switch_to().
Therefore remove the redundant check.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] switch_to: dont restore/save access & fpu regs for kernel threads
Heiko Carstens [Mon, 25 Oct 2010 14:10:18 +0000 (16:10 +0200)]
[S390] switch_to: dont restore/save access & fpu regs for kernel threads

If the previous task was a kernel thread there is no need to save the
contents of the fpu and access registers since they aren't used in
kernel mode.
For the same reason it is not necessary to restore these registers if
the next task is a kernel thread.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] Add config option for z196 code generation.
Heiko Carstens [Mon, 25 Oct 2010 14:10:17 +0000 (16:10 +0200)]
[S390] Add config option for z196 code generation.

Add a kernel config option for the IBM zEnterprise 196. This will
produce faster code on newer compilers using the -march=z196 option.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] sysinfo: display capacity adjustment indicator
Heiko Carstens [Mon, 25 Oct 2010 14:10:16 +0000 (16:10 +0200)]
[S390] sysinfo: display capacity adjustment indicator

Display machine capacity adjustment indicator and capacity
change reason if available in /proc/sysinfo.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] add z196 instructions to kernel disassembler
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:15 +0000 (16:10 +0200)]
[S390] add z196 instructions to kernel disassembler

Add the new instructions introduced with z196 to the kernel disassembler.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] add support for nonquiescing sske
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:14 +0000 (16:10 +0200)]
[S390] add support for nonquiescing sske

Improve performance of the sske operation by using the nonquiescing
variant if the affected page has no mappings established. On machines
with no support for the new sske variant the mask bit will be ignored.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] store indication fault optimization
Martin Schwidefsky [Mon, 25 Oct 2010 14:10:13 +0000 (16:10 +0200)]
[S390] store indication fault optimization

Use the store indication bit in the translation exception code on
page faults to avoid the protection faults that immediatly follow
the page fault if the access has been a write.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
14 years ago[S390] cpu hotplug/idle: move cpu_die call to enabled context
Heiko Carstens [Mon, 25 Oct 2010 14:10:12 +0000 (16:10 +0200)]
[S390] cpu hotplug/idle: move cpu_die call to enabled context

There is no difference if cpu_die is called from enabled or disabled
context. Except that the fast_gup code might be called via
cpu_die -> idle_task_exit -> __mm_drop -> crst_table_free. Which in
turn grabs and releases a spinlock using the _bh ops, which is not
allowed in irq disabled context, since spin_unlock_bh will
unconditionally enable interrupts again.
To get rid of the warning emitted by the softirq code just move the
code to enabled context.

In this case this doesn't fix a bug, we just get rid of a warning.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>