media: dvb: i2c transfers over usb cannot be done from stack

commit 6d33377f2abbf9f0e561b116dd468d1c3ff36a6a upstream.

Signed-off-by: Laurent Caumont <lcaumont2@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Fix vblank timestamp/frame counter jumps on gen2

commit a87e55f89f0b0dc541d89248a8445635936a3858 upstream.

Previously I was under the impression that the scanline counter
reads 0 when the pipe is off. Turns out that's not correct, and
instead the scanline counter simply stops when the pipe stops, and
it retains it's last value until the pipe starts up again, at which
point the scanline counter jumps to vblank start.

These jumps can cause the timestamp to jump backwards by one frame.
Since we use the timestamps to guesstimage also the frame counter
value on gen2, that would cause the frame counter to also jump
backwards, which leads to a massice difference from the previous value.
The end result is that flips/vblank events don't appear to complete as
they're stuck waiting for the frame counter to catch up to that massive
difference.

Fix the problem properly by actually making sure the scanline counter
has started to move before we assume that it's safe to enable vblank
processing.

v2: Less pointless duplication in the code (Chris)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: b7792d8b54cc ("drm/i915: Wait for pipe to start before sampling vblank timestamps on gen2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129153732.3612-1-ville.syrjala@linux.intel.com
(cherry picked from commit 8fedd64dabc86d0f31a0d1e152be3aa23c323553)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU

commit 120a264f9c2782682027d931d83dcbd22e01da80 upstream.

When no IOMMU is available, all GEM buffers allocated by Exynos DRM driver
are contiguous, because of the underlying dma_alloc_attrs() function
provides only such buffers. In such case it makes no sense to keep
BO_NONCONTIG flag for the allocated GEM buffers. This allows to avoid
failures for buffer contiguity checks in the subsequent operations on GEM
objects.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback

commit 510353a63796d467b41237ab4f136136f68c297d upstream.

get_modes() callback might be called asynchronously from the DRM core and
it is not synchronized with bridge_enable(), which sets proper runtime PM
state of the main DP device. Fix this by calling pm_runtime_get_sync()
before calling drm_get_edid(), which in turn calls drm_dp_i2c_xfer() and
analogix_dp_transfer() to ensure that main DP device is runtime active
when doing any access to its registers.

This fixes the following kernel issue on Samsung Exynos5250 Snow board:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 62 Comm: kworker/0:2 Not tainted 4.13.0-rc2-00364-g4a97a3da420b #3357
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events output_poll_execute
task: edc14800 task.stack: edcb2000
PC is at analogix_dp_transfer+0x15c/0x2fc
LR is at analogix_dp_transfer+0x134/0x2fc
pc : [<c0468538>]    lr : [<c0468510>]    psr: 60000013
sp : edcb3be8  ip : 0000002a  fp : 00000001
r10: 00000000  r9 : edcb3cd8  r8 : edcb3c40
r7 : 00000000  r6 : edd3b380  r5 : edd3b010  r4 : 00000064
r3 : 00000000  r2 : f0ad3000  r1 : edcb3c40  r0 : edd3b010
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: 4000406a  DAC: 00000051
Process kworker/0:2 (pid: 62, stack limit = 0xedcb2210)
Stack: (0xedcb3be8 to 0xedcb4000)
[<c0468538>] (analogix_dp_transfer) from [<c0424ba4>] (drm_dp_i2c_do_msg+0x8c/0x2b4)
[<c0424ba4>] (drm_dp_i2c_do_msg) from [<c0424e64>] (drm_dp_i2c_xfer+0x98/0x214)
[<c0424e64>] (drm_dp_i2c_xfer) from [<c057b2d8>] (__i2c_transfer+0x140/0x29c)
[<c057b2d8>] (__i2c_transfer) from [<c057b4a4>] (i2c_transfer+0x70/0xe4)
[<c057b4a4>] (i2c_transfer) from [<c0441de4>] (drm_do_probe_ddc_edid+0xb4/0x114)
[<c0441de4>] (drm_do_probe_ddc_edid) from [<c0441e5c>] (drm_probe_ddc+0x18/0x28)
[<c0441e5c>] (drm_probe_ddc) from [<c0445728>] (drm_get_edid+0x124/0x2d4)
[<c0445728>] (drm_get_edid) from [<c0465ea0>] (analogix_dp_get_modes+0x90/0x114)
[<c0465ea0>] (analogix_dp_get_modes) from [<c0425e8c>] (drm_helper_probe_single_connector_modes+0x198/0x68c)
[<c0425e8c>] (drm_helper_probe_single_connector_modes) from [<c04325d4>] (drm_setup_crtcs+0x1b4/0xd18)
[<c04325d4>] (drm_setup_crtcs) from [<c04344a8>] (drm_fb_helper_hotplug_event+0x94/0xd0)
[<c04344a8>] (drm_fb_helper_hotplug_event) from [<c0425a50>] (drm_kms_helper_hotplug_event+0x24/0x28)
[<c0425a50>] (drm_kms_helper_hotplug_event) from [<c04263ec>] (output_poll_execute+0x6c/0x174)
[<c04263ec>] (output_poll_execute) from [<c0136f18>] (process_one_work+0x188/0x3fc)
[<c0136f18>] (process_one_work) from [<c01371f4>] (worker_thread+0x30/0x4b8)
[<c01371f4>] (worker_thread) from [<c013daf8>] (kthread+0x128/0x164)
[<c013daf8>] (kthread) from [<c0108510>] (ret_from_fork+0x14/0x24)
Code: 0a000002 ea000009 e2544001 0a00004a (e59537c8)
---[ end trace cddc7919c79f7878 ]---

Reported-by: Misha Komarovskiy <zombah@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121074936.22520-1-m.szyprowski@samsung.com

md/r5cache: move mddev_lock() out of r5c_journal_mode_set()

commit ff35f58e8f8eb520367879a0ccc6f2ec4b62b17b upstream.

r5c_journal_mode_set() is called by r5c_journal_mode_store() and
raid_ctr() in dm-raid. We don't need mddev_lock() when calling from
raid_ctr(). This patch fixes this by moves the mddev_lock() to
r5c_journal_mode_store().

Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kdb: Fix handling of kallsyms_symbol_next() return value

commit c07d35338081d107e57cf37572d8cc931a8e32e2 upstream.

kallsyms_symbol_next() returns a boolean (true on success). Currently
kdb_read() tests the return value with an inequality that
unconditionally evaluates to true.

This is fixed in the obvious way and, since the conditional branch is
supposed to be unreachable, we also add a WARN_ON().

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

brcmfmac: change driver unbind order of the sdio function devices

commit 5c3de777bdaf48bd0cfb43097c0d0fb85056cab7 upstream.

In the function brcmf_sdio_firmware_callback() the driver is
unbound from the sdio function devices in the error path.
However, the order in which it is done resulted in a use-after-free
issue (see brcmf_ops_sdio_remove() in bcmsdh.c). Hence change
the order and first unbind sdio function #2 device and then
unbind sdio function #1 device.

Fixes: 7a51461fc2da ("brcmfmac: unbind all devices upon failure in firmware callback")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: enable RX offloading with TKIP and WEP

commit 9d0fc5a50a0548f8e5d61243e5e5f26d5c405aef upstream.

Set the flag that indicates that ICV was stripped on if
this option was enabled in the HW.

[this is needed for the 9000-series HW to work properly]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix packet injection

commit b13f43a48571f0cd0fda271b5046b65f1f268db5 upstream.

We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.

Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: add new cards for 9260 and 22000 series

commit 567deca8e72df3ceb6c07c63f8541a4928f64d3b upstream.

add 1 PCI ID for 9260 series and 1 for 22000 series.

Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: flush queue before deleting ROC

commit 6c2d49fdc5d947c5fe89935bd52e69f10000f4cb upstream.

Before deleting a time event (remain-on-channel instance), flush
the queue so that frames cannot get stuck on it. We already flush
the AUX STA queues, but a separate station is used for the P2P
Device queue.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: don't use transmit queue hang detection when it is not possible

commit 0b9832b712d6767d6c7b01965fd788d1ca84fc92 upstream.

When we act as an AP, new firmware versions handle
internally the power saving clients and the driver doesn't
know that the peers went to sleep. It is, hence, possible
that a peer goes to sleep for a long time and stop pulling
frames. This will cause its transmit queue to hang which is
a condition that triggers the recovery flow in the driver.

While this client is certainly buggy (it should have pulled
the frame based on the TIM IE in the beacon), we can't blow
up because of a buggy client.

Change the current implementation to not enable the
transmit queue hang detection on queues that serve peers
when we act as an AP / GO.

We can still enable this mechanism using the debug
configuration which can come in handy when we want to
debug why the client doesn't wake up.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: mark MIC stripped MPDUs

commit bf19037074e770aad74b3b90f37b8b98db3f3748 upstream.

When RADA is active, the hardware decrypts the packets and strips off
the MIC as it is useless after decryption. Indicate that to mac80211.

[this is needed for the 9000-series HW to work properly]
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Initialize ISAv3 MMU registers before setting partition table

commit 371b80447ff33ddac392c189cf884a5a3e18faeb upstream.

kexec can leave MMU registers set when booting into a new kernel,
the PIDR (Process Identification Register) in particular. The boot
sequence does not zero PIDR, so it only gets set when CPUs first
switch to a userspace processes (until then it's running a kernel
thread with effective PID = 0).

This leaves a window where a process table entry and page tables are
set up due to user processes running on other CPUs, that happen to
match with a stale PID. The CPU with that PID may cause speculative
accesses that address quadrant 0 (aka userspace addresses), which will
result in cached translations and PWC (Page Walk Cache) for that
process, on a CPU which is not in the mm_cpumask and so they will not
be invalidated properly.

The most common result is the kernel hanging in infinite page fault
loops soon after kexec (usually in schedule_tail, which is usually the
first non-speculative quadrant 0 access to a new PID) due to a stale
PWC. However being a stale translation error, it could result in
anything up to security and data corruption problems.

Fix this by zeroing out PIDR at boot and kexec.

Fixes: 7e381c0ff618 ("powerpc/mm/radix: Add mmu context handling callback for radix")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "powerpc: Do not call ppc_md.panic in fadump panic notifier"

commit ab9dbf771ff9b6b7e814e759213ed01d7f0de320 upstream.

This reverts commit a3b2cb30f252b21a6f962e0dd107c8b897ca65e4.

That commit tried to fix problems with panic on powerpc in certain
circumstances, where some output from the generic panic code was being
dropped.

Unfortunately, it breaks things worse in other circumstances. In
particular when running a PAPR guest, it will now attempt to reboot
instead of informing the hypervisor (KVM or PowerVM) that the guest
has crashed. The crash notification is important to some
virtualization management layers.

Revert it for now until we can come up with a better solution.

Fixes: a3b2cb30f252 ("powerpc: Do not call ppc_md.panic in fadump panic notifier")
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Tweak change log a bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: s390: Fix skey emulation permission check

commit ca76ec9ca871e67d8cd0b6caba24aca3d3ac4546 upstream.

All skey functions call skey_check_enable at their start, which checks
if we are in the PSTATE and injects a privileged operation exception
if we are.

Unfortunately they continue processing afterwards and perform the
operation anyhow as skey_check_enable does not deliver an error if the
exception injection was successful.

Let's move the PSTATE check into the skey functions and exit them on
such an occasion, also we now do not enable skey handling anymore in
such a case.

Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: a7e19ab ("KVM: s390: handle missing storage-key facility")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: fix compat system call table

commit e779498df587dd2189b30fe5b9245aefab870eb8 upstream.

When wiring up the socket system calls the compat entries were
incorrectly set. Not all of them point to the corresponding compat
wrapper functions, which clear the upper 33 bits of user space
pointers, like it is required.

Fixes: 977108f89c989 ("s390: wire up separate socketcalls system calls")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/mm: fix off-by-one bug in 5-level page table handling

commit 8d306f53b63099fec2d56300149e400d181ba4f5 upstream.

Martin Cermak reported that setting a uprobe doesn't work. Reason for
this is that the common uprobes code tries to get an unmapped area at
the last possible page within an address space.

This broke with commit 1aea9b3f9210 ("s390/mm: implement 5 level pages
tables") which introduced an off-by-one bug which prevents to map
anything at the last possible page within an address space.

The check with the off-by-one bug however can be removed since with
commit 8ab867cb0806 ("s390/mm: fix BUG_ON in crst_table_upgrade") the
necessary check is done at both call sites.

Reported-by: Martin Cermak <mcermak@redhat.com>
Bisected-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Fixes: 1aea9b3f9210 ("s390/mm: implement 5 level pages tables")
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: always save and restore all registers on context switch

commit fbbd7f1a51965b50dd12924841da0d478f3da71b upstream.

The switch_to() macro has an optimization to avoid saving and
restoring register contents that aren't needed for kernel threads.

There is however the possibility that a kernel thread execve's a user
space program. In such a case the execve'd process can partially see
the contents of the previous process, which shouldn't be allowed.

To avoid this, simply always save and restore register contents on
context switch.

Fixes: fdb6d070effba ("switch_to: dont restore/save access & fpu regs for kernel threads")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smp/hotplug: Move step CPUHP_AP_SMPCFD_DYING to the correct place

commit 46febd37f9c758b05cd25feae8512f22584742fe upstream.

Commit 31487f8328f2 ("smp/cfd: Convert core to hotplug state machine")
accidently put this step on the wrong place. The step should be at the
cpuhp_ap_states[] rather than the cpuhp_bp_states[].

grep smpcfd /sys/devices/system/cpu/hotplug/states
 40: smpcfd:prepare
129: smpcfd:dying

"smpcfd:dying" was missing before.
So was the invocation of the function smpcfd_dying_cpu().

Fixes: 31487f8328f2 ("smp/cfd: Convert core to hotplug state machine")
Signed-off-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lkml.kernel.org/r/20171128131954.81229-1-jiangshanlai@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/vt-d: Fix scatterlist offset handling

commit 29a90b70893817e2f2bb3cea40a29f5308e21b21 upstream.

The intel-iommu DMA ops fail to correctly handle scatterlists where
sg->offset is greater than PAGE_SIZE - the IOVA allocation is computed
appropriately based on the page-aligned portion of the offset, but the
mapping is set up relative to sg->page, which means it fails to actually
cover the whole buffer (and in the worst case doesn't cover it at all):

    (sg->dma_address + sg->dma_len) ----+
    sg->dma_address ---------+          |
    iov_pfn------+           |          |
                 |           |          |
                 v           v          v
iova:   a        b        c        d        e        f
        |--------|--------|--------|--------|--------|
                          <...calculated....>
                 [_____mapped______]
pfn:    0        1        2        3        4        5
        |--------|--------|--------|--------|--------|
                 ^           ^          ^
                 |           |          |
    sg->page ----+           |          |
    sg->offset --------------+          |
    (sg->offset + sg->length) ----------+

As a result, the caller ends up overrunning the mapping into whatever
lies beyond, which usually goes badly:

[  429.645492] DMAR: DRHD: handling fault status reg 2
[  429.650847] DMAR: [DMA Write] Request device [02:00.4] fault addr f2682000 ...

Whilst this is a fairly rare occurrence, it can happen from the result
of intermediate scatterlist processing such as scatterwalk_ffwd() in the
crypto layer. Whilst that particular site could be fixed up, it still
seems worthwhile to bring intel-iommu in line with other DMA API
implementations in handling this robustly.

To that end, fix the intel_map_sg() path to line up the mapping
correctly (in units of MM pages rather than VT-d pages to match the
aligned_nrpages() calculation) regardless of the offset, and use
sg_phys() consistently for clarity.

Reported-by: Harsh Jain <Harsh@chelsio.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed by: Ashok Raj <ashok.raj@intel.com>
Tested by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Add check return value for usb_string()

commit 89b89d121ffcf8d9546633b98ded9d18b8f75891 upstream.

snd_usb_copy_string_desc() returns zero if usb_string() fails.
In case of failure, we need to check the snd_usb_copy_string_desc()'s
return value and add an exception case

Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Fix out-of-bound error

commit 251552a2b0d454badc8f486e6d79100970c744b0 upstream.

The snd_usb_copy_string_desc() retrieves the usb string corresponding to
the index number through the usb_string(). The problem is that the
usb_string() returns the length of the string (>= 0) when successful, but
it can also return a negative value about the error case or status of
usb_control_msg().

If iClockSource is '0' as shown below, usb_string() will returns -EINVAL.
This will result in '0' being inserted into buf[-22], and the following
KASAN out-of-bound error message will be output.

AudioControl Interface Descriptor:
  bLength                 8
  bDescriptorType        36
  bDescriptorSubtype     10 (CLOCK_SOURCE)
  bClockID                1
  bmAttributes         0x07 Internal programmable Clock (synced to SOF)
  bmControls           0x07
  Clock Frequency Control (read/write)
  Clock Validity Control (read-only)
  bAssocTerminal          0
  iClockSource            0

To fix it, check usb_string()'return value and bail out.

==================================================================
BUG: KASAN: stack-out-of-bounds in parse_audio_unit+0x1327/0x1960 [snd_usb_audio]
Write of size 1 at addr ffff88007e66735a by task systemd-udevd/18376

CPU: 0 PID: 18376 Comm: systemd-udevd Not tainted 4.13.0+ #3
Hardware name: LG Electronics                   15N540-RFLGL/White Tip Mountain, BIOS 15N5
Call Trace:
dump_stack+0x63/0x8d
print_address_description+0x70/0x290
? parse_audio_unit+0x1327/0x1960 [snd_usb_audio]
kasan_report+0x265/0x350
__asan_store1+0x4a/0x50
parse_audio_unit+0x1327/0x1960 [snd_usb_audio]
? save_stack+0xb5/0xd0
? save_stack_trace+0x1b/0x20
? save_stack+0x46/0xd0
? kasan_kmalloc+0xad/0xe0
? kmem_cache_alloc_trace+0xff/0x230
? snd_usb_create_mixer+0xb0/0x4b0 [snd_usb_audio]
? usb_audio_probe+0x4de/0xf40 [snd_usb_audio]
? usb_probe_interface+0x1f5/0x440
? driver_probe_device+0x3ed/0x660
? build_feature_ctl+0xb10/0xb10 [snd_usb_audio]
? save_stack_trace+0x1b/0x20
? init_object+0x69/0xa0
? snd_usb_find_csint_desc+0xa8/0xf0 [snd_usb_audio]
snd_usb_mixer_controls+0x1dc/0x370 [snd_usb_audio]
? build_audio_procunit+0x890/0x890 [snd_usb_audio]
? snd_usb_create_mixer+0xb0/0x4b0 [snd_usb_audio]
? kmem_cache_alloc_trace+0xff/0x230
? usb_ifnum_to_if+0xbd/0xf0
snd_usb_create_mixer+0x25b/0x4b0 [snd_usb_audio]
? snd_usb_create_stream+0x255/0x2c0 [snd_usb_audio]
usb_audio_probe+0x4de/0xf40 [snd_usb_audio]
? snd_usb_autosuspend.part.7+0x30/0x30 [snd_usb_audio]
? __pm_runtime_idle+0x90/0x90
? kernfs_activate+0xa6/0xc0
? usb_match_one_id_intf+0xdc/0x130
? __pm_runtime_set_status+0x2d4/0x450
usb_probe_interface+0x1f5/0x440

Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: Remove spurious WARN_ON() at timer check

commit 43a3542870328601be02fcc9d27b09db467336ef upstream.

The use of snd_BUG_ON() in ALSA sequencer timer may lead to a spurious
WARN_ON() when a slave timer is deployed as its backend and a
corresponding master timer stops meanwhile.  The symptom was triggered
by syzkaller spontaneously.

Since the NULL timer is valid there, rip off snd_BUG_ON().

Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: pcm: prevent UAF in snd_pcm_info

commit 362bca57f5d78220f8b5907b875961af9436e229 upstream.

When the device descriptor is closed, the `substream->runtime` pointer
is freed. But another thread may be in the ioctl handler, case
SNDRV_CTL_IOCTL_PCM_INFO. This case calls snd_pcm_info_user() which
calls snd_pcm_info() which accesses the now freed `substream->runtime`.

Note: this fixes CVE-2017-0861

Signed-off-by: Robb Glasser <rglasser@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - New codec support for ALC257

commit f429e7e494afaded76e62c6f98211a635aa03098 upstream.

Add new support for ALC257 codec.

[ It's supposed to be almost equivalent with other ALC25x variants,
  just adding another type and id -- tiwai ]

Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: handle errors while updating refcounts in update_ref_for_cow

commit 692826b2738101549f032a761a9191636e83be4e upstream.

Since commit fb235dc06fa (btrfs: qgroup: Move half of the qgroup
accounting time out of commit trans) the assumption that
btrfs_add_delayed_{data,tree}_ref can only return 0 or -ENOMEM has
been false.  The qgroup operations call into btrfs_search_slot
and friends and can now return the full spectrum of error codes.

Fortunately, the fix here is easy since update_ref_for_cow failing
is already handled so we just need to bail early with the error
code.

Fixes: fb235dc06fa (btrfs: qgroup: Move half of the qgroup accounting ...)
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Edmund Nadolski <enadolski@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix missing error return in btrfs_drop_snapshot

commit e19182c0fff451e3744c1107d98f072e7ca377a0 upstream.

If btrfs_del_root fails in btrfs_drop_snapshot, we'll pick up the
error but then return 0 anyway due to mixing err and ret.

Fixes: 79787eaab4612 ("btrfs: replace many BUG_ONs with proper error handling")
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: fix APIC page invalidation

commit b1394e745b9453dcb5b0671c205b770e87dedb87 upstream.

Implementation of the unpinned APIC page didn't update the VMCS address
cache when invalidation was done through range mmu notifiers.
This became a problem when the page notifier was removed.

Re-introduce the arch-specific helper and call it from ...range_start.

Reported-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Fixes: 38b9917350cb ("kvm: vmx: Implement set_apic_access_page_addr")
Fixes: 369ea8242c0f ("mm/rmap: update to new mmu_notifier semantic v2")
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Wanpeng Li <wanpeng.li@hotmail.com>
Tested-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/PCI: Make broadcom_postcore_init() check acpi_disabled

commit ddec3bdee05b06f1dda20ded003c3e10e4184cab upstream.

acpi_os_get_root_pointer() may return a valid address even if acpi_disabled
is set, but the host bridge information from the ACPI tables is not going
to be used in that case and the Broadcom host bridge initialization should
not be skipped then, So make broadcom_postcore_init() check acpi_disabled
too to avoid this issue.

Fixes: 6361d72b04d1 (x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan)
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Link: https://lkml.kernel.org/r/3186627.pxZj1QbYNg@aspire.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/idt: Load idt early in start_secondary

commit 55d2d0ad2fb4325f615d1950486fbc5e6fba1769 upstream.

On a secondary, idt is first loaded in cpu_init() with load_current_idt(),
i.e. no exceptions can be handled before that point.

The conversion of WARN() to use UD requires the IDT being loaded earlier as
any warning between start_secondary() and load_curren_idt() in cpu_init()
will result in an unhandled @UD exception and therefore fail the bringup of
the CPU.

Install the IDT handlers right in start_secondary() before calling cpu_init().

[ tglx: Massaged changelog ]

Fixes: 9a93848fe787 ("x86/debug: Implement __WARN() using UD0")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Cc: bp@alien8.de
Cc: rostedt@goodmis.org
Cc: luto@kernel.org
Link: https://lkml.kernel.org/r/1511792499-4073-1-git-send-email-chuhu@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

X.509: fix comparisons of ->pkey_algo

commit 54c1fb39fe0495f846539ab765925b008f86801c upstream.

->pkey_algo used to be an enum, but was changed to a string by commit
4e8ae72a75aa ("X.509: Make algo identifiers text instead of enum").  But
two comparisons were not updated.  Fix them to use strcmp().

This bug broke signature verification in certain configurations,
depending on whether the string constants were deduplicated or not.

Fixes: 4e8ae72a75aa ("X.509: Make algo identifiers text instead of enum")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

X.509: reject invalid BIT STRING for subjectPublicKey

commit 0f30cbea005bd3077bd98cd29277d7fc2699c1da upstream.

Adding a specially crafted X.509 certificate whose subjectPublicKey
ASN.1 value is zero-length caused x509_extract_key_data() to set the
public key size to SIZE_MAX, as it subtracted the nonexistent BIT STRING
metadata byte.  Then, x509_cert_parse() called kmemdup() with that bogus
size, triggering the WARN_ON_ONCE() in kmalloc_slab().

This appears to be harmless, but it still must be fixed since WARNs are
never supposed to be user-triggerable.

Fix it by updating x509_cert_parse() to validate that the value has a
BIT STRING metadata byte, and that the byte is 0 which indicates that
the number of bits in the bitstring is a multiple of 8.

It would be nice to handle the metadata byte in asn1_ber_decoder()
instead.  But that would be tricky because in the general case a BIT
STRING could be implicitly tagged, and/or could legitimately have a
length that is not a whole number of bytes.

Here was the WARN (cleaned up slightly):

    WARNING: CPU: 1 PID: 202 at mm/slab_common.c:971 kmalloc_slab+0x5d/0x70 mm/slab_common.c:971
    Modules linked in:
    CPU: 1 PID: 202 Comm: keyctl Tainted: G    B            4.14.0-09238-g1d3b78bbc6e9 #26
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
    task: ffff880033014180 task.stack: ffff8800305c8000
    Call Trace:
     __do_kmalloc mm/slab.c:3706 [inline]
     __kmalloc_track_caller+0x22/0x2e0 mm/slab.c:3726
     kmemdup+0x17/0x40 mm/util.c:118
     kmemdup include/linux/string.h:414 [inline]
     x509_cert_parse+0x2cb/0x620 crypto/asymmetric_keys/x509_cert_parser.c:106
     x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174
     asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388
     key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850
     SYSC_add_key security/keys/keyctl.c:122 [inline]
     SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62
     entry_SYSCALL_64_fastpath+0x1f/0x96

Fixes: 42d5ec27f873 ("X.509: Add an ASN.1 decoder")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: reject NULL restriction string when type is specified

commit 18026d866801d0c52e5550210563222bd6c7191d upstream.

keyctl_restrict_keyring() allows through a NULL restriction when the
"type" is non-NULL, which causes a NULL pointer dereference in
asymmetric_lookup_restriction() when it calls strcmp() on the
restriction string.

But no key types actually use a "NULL restriction" to mean anything, so
update keyctl_restrict_keyring() to reject it with EINVAL.

Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 97d3aa0f3134 ("KEYS: Add a lookup_restriction function for the asymmetric key type")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: add missing permission check for request_key() destination

commit 4dca6ea1d9432052afb06baf2e3ae78188a4410b upstream.

When the request_key() syscall is not passed a destination keyring, it
links the requested key (if constructed) into the "default" request-key
keyring.  This should require Write permission to the keyring.  However,
there is actually no permission check.

This can be abused to add keys to any keyring to which only Search
permission is granted.  This is because Search permission allows joining
the keyring.  keyctl_set_reqkey_keyring(KEY_REQKEY_DEFL_SESSION_KEYRING)
then will set the default request-key keyring to the session keyring.
Then, request_key() can be used to add keys to the keyring.

Both negatively and positively instantiated keys can be added using this
method.  Adding negative keys is trivial.  Adding a positive key is a
bit trickier.  It requires that either /sbin/request-key positively
instantiates the key, or that another thread adds the key to the process
keyring at just the right time, such that request_key() misses it
initially but then finds it in construct_alloc_key().

Fix this bug by checking for Write permission to the keyring in
construct_get_dest_keyring() when the default keyring is being used.

We don't do the permission check for non-default keyrings because that
was already done by the earlier call to lookup_user_key().  Also,
request_key_and_link() is currently passed a 'struct key *' rather than
a key_ref_t, so the "possessed" bit is unavailable.

We also don't do the permission check for the "requestor keyring", to
continue to support the use case described by commit 8bbf4976b59f
("KEYS: Alter use of key instantiation link-to-keyring argument") where
/sbin/request-key recursively calls request_key() to add keys to the
original requestor's destination keyring.  (I don't know of any users
who actually do that, though...)

Fixes: 3e30148c3d52 ("[PATCH] Keys: Make request-key create an authorisation key")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASN.1: check for error from ASN1_OP_END__ACT actions

commit 81a7be2cd69b412ab6aeacfe5ebf1bb6e5bce955 upstream.

asn1_ber_decoder() was ignoring errors from actions associated with the
opcodes ASN1_OP_END_SEQ_ACT, ASN1_OP_END_SET_ACT,
ASN1_OP_END_SEQ_OF_ACT, and ASN1_OP_END_SET_OF_ACT.  In practice, this
meant the pkcs7_note_signed_info() action (since that was the only user
of those opcodes).  Fix it by checking for the error, just like the
decoder does for actions associated with the other opcodes.

This bug allowed users to leak slab memory by repeatedly trying to add a
specially crafted "pkcs7_test" key (requires CONFIG_PKCS7_TEST_KEY).

In theory, this bug could also be used to bypass module signature
verification, by providing a PKCS#7 message that is misparsed such that
a signature's ->authattrs do not contain its ->msgdigest.  But it
doesn't seem practical in normal cases, due to restrictions on the
format of the ->authattrs.

Fixes: 42d5ec27f873 ("X.509: Add an ASN.1 decoder")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASN.1: fix out-of-bounds read when parsing indefinite length item

commit e0058f3a874ebb48b25be7ff79bc3b4e59929f90 upstream.

In asn1_ber_decoder(), indefinitely-sized ASN.1 items were being passed
to the action functions before their lengths had been computed, using
the bogus length of 0x80 (ASN1_INDEFINITE_LENGTH).  This resulted in
reading data past the end of the input buffer, when given a specially
crafted message.

Fix it by rearranging the code so that the indefinite length is resolved
before the action is called.

This bug was originally found by fuzzing the X.509 parser in userspace
using libFuzzer from the LLVM project.

KASAN report (cleaned up slightly):

    BUG: KASAN: slab-out-of-bounds in memcpy ./include/linux/string.h:341 [inline]
    BUG: KASAN: slab-out-of-bounds in x509_fabricate_name.constprop.1+0x1a4/0x940 crypto/asymmetric_keys/x509_cert_parser.c:366
    Read of size 128 at addr ffff880035dd9eaf by task keyctl/195

    CPU: 1 PID: 195 Comm: keyctl Not tainted 4.14.0-09238-g1d3b78bbc6e9 #26
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
    Call Trace:
     __dump_stack lib/dump_stack.c:17 [inline]
     dump_stack+0xd1/0x175 lib/dump_stack.c:53
     print_address_description+0x78/0x260 mm/kasan/report.c:252
     kasan_report_error mm/kasan/report.c:351 [inline]
     kasan_report+0x23f/0x350 mm/kasan/report.c:409
     memcpy+0x1f/0x50 mm/kasan/kasan.c:302
     memcpy ./include/linux/string.h:341 [inline]
     x509_fabricate_name.constprop.1+0x1a4/0x940 crypto/asymmetric_keys/x509_cert_parser.c:366
     asn1_ber_decoder+0xb4a/0x1fd0 lib/asn1_decoder.c:447
     x509_cert_parse+0x1c7/0x620 crypto/asymmetric_keys/x509_cert_parser.c:89
     x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174
     asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388
     key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850
     SYSC_add_key security/keys/keyctl.c:122 [inline]
     SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62
     entry_SYSCALL_64_fastpath+0x1f/0x96

    Allocated by task 195:
     __do_kmalloc_node mm/slab.c:3675 [inline]
     __kmalloc_node+0x47/0x60 mm/slab.c:3682
     kvmalloc ./include/linux/mm.h:540 [inline]
     SYSC_add_key security/keys/keyctl.c:104 [inline]
     SyS_add_key+0x19e/0x290 security/keys/keyctl.c:62
     entry_SYSCALL_64_fastpath+0x1f/0x96

Fixes: 42d5ec27f873 ("X.509: Add an ASN.1 decoder")
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi/esrt: Use memunmap() instead of kfree() to free the remapping

commit 89c5a2d34bda58319e3075e8e7dd727ea25a435c upstream.

The remapping result of memremap() should be freed with memunmap(), not kfree().

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20171206095010.24170-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Move some sysfs files to be read-only by root

commit af97a77bc01ce49a466f9d4c0125479e2e2230b6 upstream.

Thanks to the scripts/leaking_addresses.pl script, it was found that
some EFI values should not be readable by non-root users.

So make them root-only, and to do that, add a __ATTR_RO_MODE() macro to
make this easier, and use it in other places at the same time.

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20171206095010.24170-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: libsas: align sata_device's rps_resp on a cacheline

commit c2e8fbf908afd81ad502b567a6639598f92c9b9d upstream.

The rps_resp buffer in ata_device is a DMA target, but it isn't
explicitly cacheline aligned. Due to this, adjacent fields can be
overwritten with stale data from memory on non-coherent architectures.
As a result, the kernel is sometimes unable to communicate with an SATA
device behind a SAS expander.

Fix this by ensuring that the rps_resp buffer is cacheline aligned.

This issue is similar to that fixed by Commit 84bda12af31f93 ("libata:
align ap->sector_buf") and Commit 4ee34ea3a12396f35b26 ("libata: Align
ata_device's id on a cacheline").

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: use dma_get_cache_alignment() as minimum DMA alignment

commit 90addc6b3c9cda0146fbd62a08e234c2b224a80c upstream.

In non-coherent DMA mode, kernel uses cache flushing operations to
maintain I/O coherency, so scsi's block queue should be aligned to the
value returned by dma_get_cache_alignment().  Otherwise, If a DMA buffer
and a kernel structure share a same cache line, and if the kernel
structure has dirty data, cache_invalidate (no writeback) will cause
data corruption.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
[hch: rebased and updated the comment and changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: dma-mapping: always provide dma_get_cache_alignment

commit 860dd4424f344400b491b212ee4acb3a358ba9d9 upstream.

Provide the dummy version of dma_get_cache_alignment that always returns
1 even if CONFIG_HAS_DMA is not set, so that drivers and subsystems can
use it without ifdefs.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

isa: Prevent NULL dereference in isa_bus driver callbacks

commit 5a244727f428a06634f22bb890e78024ab0c89f3 upstream.

The isa_driver structure for an isa_bus device is stored in the device
platform_data member of the respective device structure. This
platform_data member may be reset to NULL if isa_driver match callback
for the device fails, indicating a device unsupported by the ISA driver.

This patch fixes a possible NULL pointer dereference if one of the
isa_driver callbacks to attempted for an unsupported device. This error
should not occur in practice since ISA devices are typically manually
configured and loaded by the users, but we may as well prevent this
error from popping up for the 0day testers.

Fixes: a5117ba7da37 ("[PATCH] Driver model: add ISA bus")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: vpd: Fix platform driver and device registration/unregistration

commit 0631fb8b027f5968c2f5031f0b3ff7be3e4bebcc upstream.

The driver exit function needs to unregister both platform device and
driver. Also, during registration, register driver first and perform
error checks.

Fixes: 049a59db34eb ("firmware: Google VPD sysfs driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: vpd: Tie firmware kobject to device lifetime

commit e4b28b3c3a405b251fa25db58abe1512814a680a upstream.

It doesn't make sense to have /sys/firmware/vpd if the device is not
instantiated, so tie its lifetime to the device.

Fixes: 049a59db34eb ("firmware: Google VPD sysfs driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: vpd: Destroy vpd sections in remove function

commit 811d7e0215fb738fb9a9f0bcb1276516ad161ed1 upstream.

vpd sections are initialized during probe and thus should be destroyed
in the remove function.

Fixes: 049a59db34eb ("firmware: Google VPD sysfs driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: cleanup FIRMWARE_IN_KERNEL message

commit 0946b2fb38fdb6585a5ac3ca84ac73924f645952 upstream.

The help for FIRMWARE_IN_KERNEL still references the firmware_install
command that was recently removed by commit 5620a0d1aacd ("firmware:
delete in-kernel firmware").

Clean up the message to direct the user to their distribution's
linux-firmware package, and remove any reference to firmware being
included in the kernel source tree.

Fixes: 5620a0d1aacd ("firmware: delete in-kernel firmware").
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv: kvp: Avoid reading past allocated blocks from KVP file

commit 297d6b6e56c2977fc504c61bbeeaa21296923f89 upstream.

While reading in more than one block (50) of KVP records, the allocation
goes per block, but the reads used the total number of allocated records
(without resetting the pointer/stream). This causes the records buffer to
overrun when the refresh reads more than one block over the previous
capacity (e.g. reading more than 100 KVP records whereas the in-memory
database was empty before).

Fix this by reading the correct number of KVP records from file each time.

Signed-off-by: Paul Meyer <Paul.Meyer@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drivers: hv: vmbus: Fix a rescind issue

commit 7fa32e5ec28b1609abc0b797b58267f725fc3964 upstream.

The current rescind processing code will not correctly handle
the case where the host immediately rescinds a channel that has
been offerred. In this case, we could be blocked in the open call and
since the channel is rescinded, the host will not respond and we could
be blocked forever in the vmbus open call.i Fix this problem.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: armada-37xx: Fix direction_output() callback behavior

commit 6702abb3bf2394f250af0ee04070227bb5dda788 upstream.

The direction_output callback of the gpio_chip structure is supposed to
set the output direction but also to set the value of the gpio. For the
armada-37xx driver this callback acted as the gpio_set_direction callback
for the pinctrl.

This patch fixes the behavior of the direction_output callback by also
applying the value received as parameter.

Fixes: 5715092a458c ("pinctrl: armada-37xx: Add gpio support")
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: meson-saradc: Meson8 and Meson8b do not have REG11 and REG13

commit 96748823c483c6eed8321f78bd128dd33f09c55c upstream.

The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.

Fixes: 6c76ed31cd05 ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: meson-saradc: initialize the bandgap correctly on older SoCs

commit d85eed9f576369bc90322659de96b7dbea1f9a57 upstream.

Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.

Fixes: 6c76ed31cd05 ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: meson-saradc: fix the bit_idx of the adc_en clock

commit 7a6b0420d2fe4ce59437bd318826fe468f0d71ae upstream.

Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.

This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.

Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: cpcap: fix incorrect validation

commit 81b039ec36a41a5451e1e36f05bb055eceab1dc8 upstream.

Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().

Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632d50 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: health: max30102: Temperature should be in milli Celsius

commit ad44a9f804c1591ba2a2ec0ac8d916a515d2790c upstream.

As per ABI temperature should be in milli Celsius after scaling,
not Celsius

Note on stable cc.  This driver is breaking the standard IIO
ABI. (JC)

Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: stm32: fix adc/trigger link error

commit 6d745ee8b5e81f3a33791e3c854fbbfd6f3e585e upstream.

The ADC driver can trigger on either the timer or the lptim
trigger, but it only uses a Kconfig 'select' statement
to ensure that the first of the two is present. When the lptim
trigger is enabled as a loadable module, and the adc driver
is built-in, we now get a link error:

drivers/iio/adc/stm32-adc.o: In function `stm32_adc_get_trig_extsel':
stm32-adc.c:(.text+0x4e0): undefined reference to `is_stm32_lptim_trigger'

We could use a second 'select' statement and always have both
trigger drivers enabled when the adc driver is, but it seems that
the lptimer trigger was intentionally left optional, so it seems
better to keep it that way.

This adds a hack to use 'IS_REACHABLE()' rather than 'IS_ENABLED()',
which avoids the link error, but instead leads to the lptimer trigger
not being used in the broken configuration. I've added a runtime
warning for this case to help users figure out what they did wrong
if this should ever be done by accident.

Fixes: f0b638a7f6db ("iio: adc: stm32: add support for lptimer triggers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio: release virtio index when fail to device_register

commit e60ea67bb60459b95a50a156296041a13e0e380e upstream.

index can be reused by other virtio device.

Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: peak/pcie_fd: fix potential bug in restarting tx queue

commit 91785de6f94b58c3fb6664609e3682f011bd28d2 upstream.

Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: usb_8dev: cancel urb on -EPIPE and -EPROTO

commit 12147edc434c9e4c7c2f5fee2e5519b2e5ac34ce upstream.

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.

Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: esd_usb2: cancel urb on -EPIPE and -EPROTO

commit 7a31ced3de06e9878e4f9c3abe8f87d9344d8144 upstream.

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.

Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: ems_usb: cancel urb on -EPIPE and -EPROTO

commit bd352e1adfe0d02d3ea7c8e3fb19183dc317e679 upstream.

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.

Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: mcba_usb: cancel urb on -EPROTO

commit c7f33023308f3142433b7379718af5f0c2c322a6 upstream.

When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.

Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.

Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: kvaser_usb: cancel urb on -EPIPE and -EPROTO

commit 6aa8d5945502baf4687d80de59b7ac865e9e666b upstream.

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.

Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: kvaser_usb: ratelimit errors if incomplete messages are received

commit 8bd13bd522ff7dfa0eb371921aeb417155f7a3be upstream.

Avoid flooding the kernel log with "Formate error", if incomplete message
are received.

Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: kvaser_usb: Fix comparison bug in kvaser_usb_read_bulk_callback()

commit e84f44eb5523401faeb9cc1c97895b68e3cfb78d upstream.

The conditon in the while-loop becomes true when actual_length is less than
2 (MSG_HEADER_LEN). In best case we end up with a former, already
dispatched msg, that got msg->len greater than actual_length. This will
result in a "Format error" error printout.

Problem seen when unplugging a Kvaser USB device connected to a vbox guest.

warning: comparison between signed and unsigned integer expressions
[-Wsign-compare]

Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: kvaser_usb: free buf in error paths

commit 435019b48033138581a6171093b181fc6b4d3d30 upstream.

The allocated buffer was not freed if usb_submit_urb() failed.

Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: ti_hecc: Fix napi poll return value for repoll

commit f6c23b174c3c96616514827407769cbcfc8005cf upstream.

After commit d75b1ade567f ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget.
So we need to return budget if there are still packets to receive.

Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: flexcan: fix VF610 state transition issue

commit 29c64b17a0bc72232acc45e9533221d88a262efb upstream.

Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for VF610 to report correct state
transitions.

Tested-by: Mirza Krak <mirza.krak@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: peak/pci: fix potential bug when probe() fails

commit 5c2cb02edf79ad79d9b8d07c6d52243a948c4c9f upstream.

PCI/PCIe drivers for PEAK-System CAN/CAN-FD interfaces do some access to the
PCI config during probing. In case one of these accesses fails, a POSITIVE
PCIBIOS_xxx error code is returned back. This POSITIVE error code MUST be
converted into a NEGATIVE errno for the probe() function to indicate it
failed. Using the pcibios_err_to_errno() function, we make sure that the
return code will always be negative.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: mcba_usb: fix device disconnect bug

commit 1cb35a33a28394fd711bb26ddf3a564f4e9d9125 upstream.

Currently, when you disconnect the device, the driver infinitely
resubmits all URBs, so you see:

Rx URB aborted (-32)

in an infinite loop.

Fix this by catching -EPIPE (what we get in urb->status when the device
disconnects) and not resubmitting.

With this patch, I can plug and unplug many times and the driver
recovers correctly.

Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: f_fs: Force Reserved1=1 in OS_DESC_EXT_COMPAT

commit a3acc696085e112733d191a77b106e67a4fa110b upstream.

The specification says that the Reserved1 field in OS_DESC_EXT_COMPAT
must have the value "1", but when this feature was first implemented we
rejected any non-zero values.

This was adjusted to accept all non-zero values (while now rejecting
zero) in commit 53642399aa71 ("usb: gadget: f_fs: Fix wrong check on
reserved1 of OS_DESC_EXT_COMPAT"), but that breaks any userspace
programs that worked previously by returning EINVAL when Reserved1 == 0
which was previously the only value that succeeded!

If we just set the field to "1" ourselves, both old and new userspace
programs continue to work correctly and, as a bonus, old programs are
now compliant with the specification without having to fix anything
themselves.

Fixes: 53642399aa71 ("usb: gadget: f_fs: Fix wrong check on reserved1 of OS_DESC_EXT_COMPAT")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serdev: ttyport: fix tty locking in close

commit 90dbad8cd6efccbdce109d5ef0724f8434a6cdde upstream.

Make sure to hold the tty lock as required when calling tty-driver
close() (e.g. to avoid racing with hangup()).

Note that the serport active flag is currently set under the lock at
controller open, but really isn't protected by it.

Fixes: cd6484e1830b ("serdev: Introduce new bus for serial attached devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serdev: ttyport: fix NULL-deref on hangup

commit 8bcd4e6a8decac251d55c4377e2e67f052777ce0 upstream.

Make sure to use a properly refcounted tty_struct in write_wake up to
avoid dereferencing a NULL-pointer when a port is being hung up.

Fixes: bed35c6dfa6a ("serdev: add a tty port controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serdev: ttyport: add missing receive_buf sanity checks

commit eb281683621b71ab9710d9dccbbef0c2e1769c97 upstream.

The receive_buf tty-port callback should return the number of bytes
accepted and must specifically never return a negative errno (or a value
larger than the buffer size) to the tty layer.

A serdev driver not providing a receive_buf callback would currently
cause the flush_to_ldisc() worker to spin in a tight loop when the tty
buffer pointers are incremented with -EINVAL (-22) after data has been
received.

A serdev driver occasionally returning a negative errno (or a too large
byte count) could cause information leaks or crashes when accessing
memory outside the tty buffers in consecutive callbacks.

Fixes: cd6484e1830b ("serdev: Introduce new bus for serial attached devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: core: Fix ->udc_set_speed() speed handling

commit a4f0927ef588cf62bb864707261482c874352942 upstream.

Currently UDC core calls ->udc_set_speed() with the speed parameter
containing the maximum speed supported by the gadget function
driver. This might very well be more than that supported by the
UDC controller driver.

Select the lesser of the 2 speeds so both UDC and gadget function
driver are operating within limits.

This fixes PHY Erratic errors and 2 second enumeration delay on
TI's AM437x platforms.

Fixes: 6099eca796ae ("usb: gadget: core: introduce ->udc_set_speed() method")
Reported-by: Dylan Howey <Dylan.Howey@tennantco.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: udc: renesas_usb3: fix number of the pipes

commit a58204ab91ad8cae4d8474aa0ba5d1fc504860c9 upstream.

This controller on R-Car Gen3 has 6 pipes that included PIPE 0 for
control actually. But, the datasheet has error in writing as it has
31 pipes. (However, the previous code defined 30 pipes wrongly...)

Anyway, this patch fixes it.

Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.5

locking/refcounts: Do not force refcount_t usage as GPL-only export

commit b562c171cf011d297059bd0265742eb5fab0ad2f upstream.

The refcount_t protection on x86 was not intended to use the stricter
GPL export. This adjusts the linkage again to avoid a regression in
the availability of the refcount API.

Reported-by: Dave Airlie <airlied@gmail.com>
Fixes: 7a46ec0e2f48 ("locking/refcounts, x86/asm: Implement fast refcount overflow protection")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ivan Kozik <ivan@ludios.org>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: fix incorrect updating of offset

commit 1d5a31582ef046d3b233f0da1a68ae26519b2f0a upstream.

The variable temp is incorrectly being updated, instead it should
be offset otherwise the loop just reads the same capability value
and loops forever.  Thanks to Alan Stern for pointing out the
correct fix to my original fix.  Fix also cleans up clang warning:

drivers/usb/host/ehci-dbg.c:840:4: warning: Value stored to 'temp'
is never read

Fixes: d49d43174400 ("USB: misc ehci updates")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbfs: Filter flags passed in from user space

commit 446f666da9f019ce2ffd03800995487e79a91462 upstream.

USBDEVFS_URB_ISO_ASAP must be accepted only for ISO endpoints.
Improve sanity checking.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: Add type-specific length check of BOS descriptors

commit 81cf4a45360f70528f1f64ba018d61cb5767249a upstream.

As most of BOS descriptors are longer in length than their header
'struct usb_dev_cap_header', comparing solely with it is not sufficient
to avoid out-of-bounds access to BOS descriptors.

This patch adds descriptor type specific length check in
usb_get_bos_descriptor() to fix the issue.

Signed-off-by: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: fix panic in xhci_free_virt_devices_depth_first

commit 80e457699a8dbdd70f2d26911e46f538645c55fc upstream.

Check vdev->real_port 0 to avoid panic
[    9.261347] [<ffffff800884a390>] xhci_free_virt_devices_depth_first+0x58/0x108
[    9.261352] [<ffffff800884a814>] xhci_mem_cleanup+0x1bc/0x570
[    9.261355] [<ffffff8008842de8>] xhci_stop+0x140/0x1c8
[    9.261365] [<ffffff80087ed304>] usb_remove_hcd+0xfc/0x1d0
[    9.261369] [<ffffff80088551c4>] xhci_plat_remove+0x6c/0xa8
[    9.261377] [<ffffff80086e928c>] platform_drv_remove+0x2c/0x70
[    9.261384] [<ffffff80086e6ea0>] __device_release_driver+0x80/0x108
[    9.261387] [<ffffff80086e7a1c>] device_release_driver+0x2c/0x40
[    9.261392] [<ffffff80086e5f28>] bus_remove_device+0xe0/0x120
[    9.261396] [<ffffff80086e2e34>] device_del+0x114/0x210
[    9.261399] [<ffffff80086e9e00>] platform_device_del+0x30/0xa0
[    9.261403] [<ffffff8008810bdc>] dwc3_otg_work+0x204/0x488
[    9.261407] [<ffffff80088133fc>] event_work+0x304/0x5b8
[    9.261414] [<ffffff80080e31b0>] process_one_work+0x148/0x490
[    9.261417] [<ffffff80080e3548>] worker_thread+0x50/0x4a0
[    9.261421] [<ffffff80080e9ea0>] kthread+0xe8/0x100
[    9.261427] [<ffffff8008083680>] ret_from_fork+0x10/0x50

The problem can occur if xhci_plat_remove() is called shortly after
xhci_plat_probe(). While xhci_free_virt_devices_depth_first been
called before the device has been setup and get real_port initialized.
The problem occurred on Hikey960 and was reproduced by Guenter Roeck
on Kevin with chromeos-4.4.

Fixes: ee8665e28e8d ("xhci: free xhci virtual devices with leaf nodes first")
Cc: Guenter Roeck <groeck@google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fan Ning <fanning4@hisilicon.com>
Signed-off-by: Li Rui <lirui39@hisilicon.com>
Signed-off-by: yangdi <yangdi10@hisilicon.com>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Don't show incorrect WARN message about events for empty rings

commit e4ec40ec4b260efcca15089de4285a0a3411259b upstream.

xHC can generate two events for a short transfer if the short TRB and
last TRB in the TD are not the same TRB.

The driver will handle the TD after the first short event, and remove
it from its internal list. Driver then incorrectly prints a warning
for the second event:

"WARN Event TRB for slot x ep y with no TDs queued"

Fix this by not printing a warning if we get a event on a empty list
if the previous event was a short event.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ulpi: fix bus-node lookup

commit 33c309ebc797b908029fd3a0851aefe697e9b598 upstream.

Fix bus-node lookup during registration, which ended up searching the whole
device tree depth-first starting at the parent (or grand parent) rather
than just matching on its children.

To make things worse, the parent (or grand-parent) node could end being
prematurely freed as well.

Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub: Cycle HUB power when initialization fails

commit 973593a960ddac0f14f0d8877d2d0abe0afda795 upstream.

Sometimes the USB device gets confused about the state of the initialization and
the connection fails. In particular, the device thinks that it's already set up
and running while the host thinks the device still needs to be configured. To
work around this issue, power-cycle the hub's output to issue a sort of "reset"
to the device. This makes the device restart its state machine and then the
initialization succeeds.

This fixes problems where the kernel reports a list of errors like this:

usb 1-1.3: device not accepting address 19, error -71

The end result is a non-functioning device. After this patch, the sequence
becomes like this:

usb 1-1.3: new high-speed USB device number 18 using ci_hdrc
usb 1-1.3: device not accepting address 18, error -71
usb 1-1.3: new high-speed USB device number 19 using ci_hdrc
usb 1-1.3: device not accepting address 19, error -71
usb 1-1-port3: attempt power cycle
usb 1-1.3: new high-speed USB device number 21 using ci_hdrc
usb-storage 1-1.3:1.2: USB Mass Storage device detected

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ccree: fix leak of import() after init()

commit c5f39d07860c35e5e4c63188139465af790f86ce upstream.

crypto_ahash_import() may be called either after
crypto_ahash_init() or without such call. Right now
we always internally call init() as part of
import(), thus leaking memory and mappings if the
user has already called init() herself.

Fix this by only calling init() internally if the
state is not already initialized.

Fixes: commit 454527d0d94f ("staging: ccree: fix hash import/export")
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dma-buf/sw_sync: force signal all unsignaled fences on dying timeline

commit ea4d5a270b57fa8d4871f372ca9b97b7697fdfda upstream.

To avoid hanging userspace components that might have been waiting on the
active fences of the destroyed timeline we need to signal with error all
remaining fences on such timeline.

This restore the default behaviour of the Android sw_sync framework, which
Android still relies on. It was broken on the dma fence conversion a few
years ago and never fixed.

v2: Do not bother with cleanup do the list (Chris Wilson)

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dominik Behr <dbehr@chromium.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907190246.16425-2-gustavo@padovan.org
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/kprobes: Disable preemption before invoking probe handler for optprobes

commit 8a2d71a3f2737e2448aa68de2b6052cb570d3d2a upstream.

Per Documentation/kprobes.txt, probe handlers need to be invoked with
preemption disabled. Update optimized_callback() to do so. Also move
get_kprobe_ctlblk() invocation post preemption disable, since it
accesses pre-cpu data.

This was not an issue so far since optprobes wasn't selected if
CONFIG_PREEMPT was enabled. Commit a30b85df7d599f ("kprobes: Use
synchronize_rcu_tasks() for optprobe with CONFIG_PREEMPT=y") changes
this.

Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/jprobes: Disable preemption when triggered through ftrace

commit 6baea433bc84cd148af1c524389a8d756f67412e upstream.

KPROBES_SANITY_TEST throws the below splat when CONFIG_PREEMPT is
enabled:

  Kprobe smoke test: started
  DEBUG_LOCKS_WARN_ON(val > preempt_count())
  ------------[ cut here ]------------
  WARNING: CPU: 19 PID: 1 at kernel/sched/core.c:3094 preempt_count_sub+0xcc/0x140
  Modules linked in:
  CPU: 19 PID: 1 Comm: swapper/0 Not tainted 4.13.0-rc7-nnr+ #97
  task: c0000000fea80000 task.stack: c0000000feb00000
  NIP:  c00000000011d3dc LR: c00000000011d3d8 CTR: c000000000a090d0
  REGS: c0000000feb03400 TRAP: 0700   Not tainted  (4.13.0-rc7-nnr+)
  MSR:  8000000000021033 <SF,ME,IR,DR,RI,LE>  CR: 28000282  XER: 00000000
  CFAR: c00000000015aa18 SOFTE: 0
  <snip>
  NIP preempt_count_sub+0xcc/0x140
  LR  preempt_count_sub+0xc8/0x140
  Call Trace:
    preempt_count_sub+0xc8/0x140 (unreliable)
    kprobe_handler+0x228/0x4b0
    program_check_exception+0x58/0x3b0
    program_check_common+0x16c/0x170
    --- interrupt: 0 at kprobe_target+0x8/0x20
                     LR = init_test_probes+0x248/0x7d0
    kp+0x0/0x80 (unreliable)
    livepatch_handler+0x38/0x74
    init_kprobes+0x1d8/0x208
    do_one_initcall+0x68/0x1d0
    kernel_init_freeable+0x298/0x374
    kernel_init+0x24/0x160
    ret_from_kernel_thread+0x5c/0x70
  Instruction dump:
  419effdc 3d22001b 39299240 81290000 2f890000 409effc8 3c82ffcb 3c62ffcb
  3884bc68 3863bc18 4803d5fd 60000000 <0fe00000> 4bffffa8 60000000 60000000
  ---[ end trace 432dd46b4ce3d29f ]---
  Kprobe smoke test: passed successfully

The issue is that we aren't disabling preemption in
kprobe_ftrace_handler(). Disable it.

Fixes: ead514d5fb30a0 ("powerpc/kprobes: Add support for KPROBES_ON_FTRACE")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Trim oops a little for formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locking/refcounts, x86/asm: Enable CONFIG_ARCH_HAS_REFCOUNT

[ Upstream commit 39208aa7ecb7d9c4e86df782b5693270313cbab1 ]

With the section inlining bug fixed for the x86 refcount protection,
we can turn the config back on.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Elena <elena.reshetova@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/1504382986-49301-3-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: multiplexer: add NULL check on devm_kzalloc() and devm_kmemdup() return values

[ Upstream commit dd92d5ea20ef8a42be7aeda08c669c586c730451 ]

Check return values from call to devm_kzalloc() and devm_kmemup()
in order to prevent a NULL pointer dereference.

This issue was detected using Coccinelle and the following semantic patch:

@@
expression x;
identifier fld;
@@

* x = devm_kzalloc(...);
   ... when != x == NULL
   x->fld

Fixes: 7ba9df54b091 ("iio: multiplexer: new iio category and iio-mux driver")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: ti-ads1015: add 10% to conversion wait time

[ Upstream commit fe895ac88b9fbdf2026f0bfd56c82747bb9d7c48 ]

As user's guide "ADS1015EVM, ADS1115EVM, ADS1015EVM-PDK, ADS1115EVM-PDK
User Guide (Rev. B)" (http://www.ti.com/lit/ug/sbau157b/sbau157b.pdf)
states at page 16:
"Note that both the ADS1115 and ADS1015 have internal clocks with a ±10%
accuracy. If performing FFT tests, frequencies may appear to be incorrect
as a result of this tolerance range.", add those 10% to converion wait
time.

Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, x86/mm: Fix performance regression in get_user_pages_fast()

[ Upstream commit 5b65c4677a57a1d4414212f9995aa0e46a21ff80 ]

The 0-day test bot found a performance regression that was tracked down to
switching x86 to the generic get_user_pages_fast() implementation:

  http://lkml.kernel.org/r/20170710024020.GA26389@yexl-desktop

The regression was caused by the fact that we now use local_irq_save() +
local_irq_restore() in get_user_pages_fast() to disable interrupts.
In x86 implementation local_irq_disable() + local_irq_enable() was used.

The fix is to make get_user_pages_fast() use local_irq_disable(),
leaving local_irq_save() for __get_user_pages_fast() that can be called
with interrupts disabled.

Numbers for pinning a gigabyte of memory, one page a time, 20 repeats:

  Before:  Average: 14.91 ms, stddev: 0.45 ms
  After:   Average: 10.76 ms, stddev: 0.18 ms

Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: linux-mm@kvack.org
Fixes: e585513b76f7 ("x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation")
Link: http://lkml.kernel.org/r/20170908215603.9189-3-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf tools: Fix leaking rec_argv in error cases

[ Upstream commit c896f85a7c15ab9d040ffac8b8003e47996602a2 ]

Let's free the allocated rec_argv in case we return early, in order to
avoid leaking memory.

This adds free() at a few very similar places across the tree where it
was missing.

Signed-off-by: Martin Kepplinger <martink@posteo.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Martin kepplinger <martink@posteo.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170913191419.29806-1-martink@posteo.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools include: Do not use poison with C++

[ Upstream commit 6ae8eefc6c8fe050f057781b70a83262eb0a61ee ]

LIST_POISON[12] are used to initialize list_head and hlist_node
pointers, and do void pointer arithmetic, which C++ doesn't like, so, to
avoid drifting from the kernel by introducing some HLIST_POISON to do
away with void pointer math, just make those poisoned pointers be NULL
when building it with a C++ compiler.

Noticed with:

  $ make LLVM_CONFIG=/usr/bin/llvm-config-3.9 LIBCLANGLLVM=1
    CXX      util/c++/clang.o
    CXX    util/c++/clang-test.o
  In file included from /home/lizj/linux/tools/include/linux/list.h:5:0,
                   from /home/lizj/linux/tools/perf/util/namespaces.h:13,
                   from /home/lizj/linux/tools/perf/util/util.h:15,
                   from /home/lizj/linux/tools/perf/util/util-cxx.h:20,
                   from util/c++/clang-c.h:5,
                   from util/c++/clang-test.cpp:2:
  /home/lizj/linux/tools/include/linux/list.h: In function ‘void list_del(list_head*)’:
  /home/lizj/linux/tools/include/linux/poison.h:14:31: error: pointer of type ‘void *’ used in arithmetic [-Werror=pointer-arith]
   # define POISON_POINTER_DELTA 0
                                 ^
  /home/lizj/linux/tools/include/linux/poison.h:22:41: note: in expansion of macro ‘POISON_POINTER_DELTA’
   #define LIST_POISON1  ((void *) 0x100 + POISON_POINTER_DELTA)
                                           ^
  /home/lizj/linux/tools/include/linux/list.h:107:16: note: in expansion of macro ‘LIST_POISON1’
    entry->next = LIST_POISON1;
                  ^
  In file included from /home/lizj/linux/tools/perf/util/namespaces.h:13:0,
                   from /home/lizj/linux/tools/perf/util/util.h:15,
                   from /home/lizj/linux/tools/perf/util/util-cxx.h:20,
                   from util/c++/clang-c.h:5,
                   from util/c++/clang-test.cpp:2:
  /home/lizj/linux/tools/include/linux/list.h:107:14: error: invalid conversion from ‘void*’ to ‘list_head*’ [-fpermissive]

Reported-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Philip Li <philip.li@intel.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-m5ei2o0mjshucbr28baf5lqz@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/ptrace: fix guarded storage regset handling

[ Upstream commit 5ef2d5231d547c672c67bdf84c13a4adaf477964 ]

If the guarded storage regset for current is supposed to be changed,
the regset from user space is copied directly into the guarded storage
control block.

If then the process gets scheduled away while the control block is
being copied and before the new control block has been loaded, the
result is random: the process can be scheduled away due to a page
fault or preemption. If that happens the already copied parts will be
overwritten by save_gs_cb(), called from switch_to().

Avoid this by copying the data to a temporary buffer on the stack and
do the actual update with preemption disabled.

Fixes: f5bbd7219891 ("s390/ptrace: guarded storage regset for the current task")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locking/refcounts, x86/asm: Use unique .text section for refcount exceptions

[ Upstream commit 564c9cc84e2adf8a6671c1937f0a9fe3da2a4b0e ]

Using .text.unlikely for refcount exceptions isn't safe because gcc may
move entire functions into .text.unlikely (e.g. in6_dev_dev()), which
would cause any uses of a protected refcount_t function to stay inline
with the function, triggering the protection unconditionally:

        .section        .text.unlikely,"ax",@progbits
        .type   in6_dev_get, @function
in6_dev_getx:
.LFB4673:
        .loc 2 4128 0
        .cfi_startproc
...
        lock; incl 480(%rbx)
        js 111f
        .pushsection .text.unlikely
111:    lea 480(%rbx), %rcx
112:    .byte 0x0f, 0xff
.popsection
113:

This creates a unique .text..refcount section and adds an additional
test to the exception handler to WARN in the case of having none of OF,
SF, nor ZF set so we can see things like this more easily in the future.

The double dot for the section name keeps it out of the TEXT_MAIN macro
namespace, to avoid collisions and so it can be put at the end with
text.unlikely to keep the cold code together.

See commit:

  cb87481ee89db ("kbuild: linker script do not match C names unless LD_DEAD_CODE_DATA_ELIMINATION is configured")

... which matches C names: [a-zA-Z0-9_] but not ".".

Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Elena <elena.reshetova@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch <linux-arch@vger.kernel.org>
Fixes: 7a46ec0e2f48 ("locking/refcounts, x86/asm: Implement fast refcount overflow protection")
Link: http://lkml.kernel.org/r/1504382986-49301-2-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kprobes/x86: Disable preemption in ftrace-based jprobes

[ Upstream commit 5bb4fc2d8641219732eb2bb654206775a4219aca ]

Disable preemption in ftrace-based jprobe handlers as
described in Documentation/kprobes.txt:

  "Probe handlers are run with preemption disabled."

This will fix jprobes behavior when CONFIG_PREEMPT=y.

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/150581530024.32348.9863783558598926771.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf test attr: Fix python error on empty result

[ Upstream commit 3440fe2790aa3d13530260af6033533b18959aee ]

Commit d78ada4a767 ("perf tests attr: Do not store failed events") does
not create an event file in the /tmp directory when the
perf_open_event() system call failed.

This can lead to a situation where not /tmp/event-xx-yy-zz result file
exists at all (for example on a s390x virtual machine environment) where
no CPUMF hardware is available.

The following command then fails with a python call back chain instead
of printing failure:

  [root@s8360046 perf]# /usr/bin/python2 ./tests/attr.py -d ./tests/attr/ \
      -p ./perf -v -ttest-stat-basic
  running './tests/attr//test-stat-basic'
  Traceback (most recent call last):
    File "./tests/attr.py", line 379, in <module>
      main()
    File "./tests/attr.py", line 370, in main
      run_tests(options)
    File "./tests/attr.py", line 311, in run_tests
      Test(f, options).run()
    File "./tests/attr.py", line 300, in run
      self.compare(self.expect, self.result)
    File "./tests/attr.py", line 248, in compare
      exp_event.diff(res_event)
  UnboundLocalError: local variable 'res_event' referenced before assignment
  [root@s8360046 perf]#

This patch catches this pitfall and prints an error message instead:

  [root@s8360047 perf]# /usr/bin/python2 ./tests/attr.py -d ./tests/attr/ \
       -p ./perf  -vvv -ttest-stat-basic
  running './tests/attr//test-stat-basic'
    loading expected events
      Event event:base-stat
        fd = 1
        group_fd = -1
        flags = 0|8
        [....]
        sample_regs_user = 0
        sample_stack_user = 0
    'PERF_TEST_ATTR=/tmp/tmpJbMQMP ./perf stat -o /tmp/tmpJbMQMP/perf.data -e cycles kill >/dev/null 2>&1' ret '1', expected '1'
    loading result events
    compare
      matching [event:base-stat]
      match: [event:base-stat] matches []
      res_event is empty
  FAILED './tests/attr//test-stat-basic' - match failure
  [root@s8360047 perf]#

Signed-off-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
LPU-Reference: 20170913081209.39570-1-tmricht@linux.vnet.ibm.com
Link: http://lkml.kernel.org/n/tip-04d63nn7svfgxdhi60gq2mlm@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf test attr: Fix ignored test case result

[ Upstream commit 22905582f6dd4bbd0c370fe5732c607452010c04 ]

Command perf test -v 16 (Setup struct perf_event_attr test) always
reports success even if the test case fails.  It works correctly if you
also specify -F (for don't fork).

   root@s35lp76 perf]# ./perf test -v 16
   15: Setup struct perf_event_attr               :
   --- start ---
   running './tests/attr/test-record-no-delay'
   [ perf record: Woken up 1 times to write data ]
   [ perf record: Captured and wrote 0.002 MB /tmp/tmp4E1h7R/perf.data
     (1 samples) ]
   expected task=0, got 1
   expected precise_ip=0, got 3
   expected wakeup_events=1, got 0
   FAILED './tests/attr/test-record-no-delay' - match failure
   test child finished with 0
   ---- end ----
   Setup struct perf_event_attr: Ok

The reason for the wrong error reporting is the return value of the
system() library call. It is called in run_dir() file tests/attr.c and
returns the exit status, in above case 0xff00.

This value is given as parameter to the exit() function which can only
handle values 0-0xff.

The child process terminates with exit value of 0 and the parent does
not detect any error.

This patch corrects the error reporting and prints the correct test
result.

Signed-off-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
LPU-Reference: 20170913081209.39570-2-tmricht@linux.vnet.ibm.com
Link: http://lkml.kernel.org/n/tip-rdube6rfcjsr1nzue72c7lqn@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>