iio: st_sensors: verify interrupt event to status

This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.

This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.

Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: st_sensors: read each channel individually

The current buffer read code tries to optimize reads from the
sensor data registers by issuing a single read operation across
all the indata registers.

This doesn't work: when the LIS331DL accelerometer sensor is
configured to open drain, active low interrupt mode, this will
just clear the XDA (X-axis data available) bit in the STATUS_REG
register (0x27), while YDA, ZDA and even ZYXDA remain set to 1,
and the internal logic of the sensor holds the DRDY (INT1) line
asserted (the value of the status register is 0xee).

If we instead issue one read operation per enabled channel
(X, Y, Z) things start working and we can use open drain and
active low interrupts.

Note that a backported patch fixing this issue will be heading
via the fixes branch but changes in this file already in staging-next
will make that patch 'look' rather different.  The code in here
is the correct one when that clash hits.

Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mxs-lradc: move STMP reset out of ADC init

This patch moves the STMP reset out of ADC init function so as to remove
the possiblity of an error return which will be necessary for PM ops support
patches to follow.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mxs-lradc: move TS config into suitable function

This patch moves the touchscreen type configuration into
a more suitable function. Btw this simplifies PM ops later.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: magn: bmc150: Introduce SPI support

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: magn: Split bmc150 driver in common/i2c parts

This is useful for easily adding SPI support in later patches.

Now bmc150_magn exports core functions to be used by I2C/SPI drivers
instances. For the moment only I2C driver is supported.

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: set INPUT_PROP_DIRECT

Set INPUT_PROP_DIRECT to indicate that it is a touchscreen on the
device to help userspace classify it.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

ti-adc081c: Initial triggered buffer support

Using this requires software triggers like CONFIG_IIO_HRTIMER_TRIGGER.

The device can be configured to do internal periodic sampling but does not
offer some sort of interrupt on data ready. Interrupts can only trigger when
values get out of a specific range.

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

ti-adc081c: Add support for adc101c and adc121c

These chips have an almost identical interface but support a different
number of value bits. Datasheet links for comparison:

 * http://www.ti.com/lit/ds/symlink/adc081c021.pdf
 * http://www.ti.com/lit/ds/symlink/adc101c021.pdf
 * http://www.ti.com/lit/ds/symlink/adc121c021.pdf

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: frequency: ad9523: use unsigned int rather then bare unsigned

This fix checkpatch warnings:

WARNING: Prefer 'unsigned int' to bare use of 'unsigned'

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light: new driver for the ROHM BH1780

This is a reimplementation of the old misc device driver for the
ROHM BH1780 ambient light sensor (drivers/misc/bh1780gli.c).

Differences from the old driver:
- Uses the IIO framework
- Uses runtime PM to idle the hardware after 5 seconds
- No weird custom power management from userspace
- No homebrewn values in sysfs

This uses the same (undocumented) device tree compatible-string
as the old driver ("rohm,bh1780gli").

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Indent if statement

Indent lines inside if statement.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:adis16240: Set self_test_no_autoclear flag

The ADIS16201 does not automatically clear the self test flag bit the self
test has been, so clear it manually. Otherwise we'll see a offset caused by
the self-test bias on the output values during normal operation.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:adis16209: Set self_test_no_autoclear flag

The ADIS16201 does not automatically clear the self test flag bit the self
test has been, so clear it manually. Otherwise we'll see a offset caused by
the self-test bias on the output values during normal operation.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:adis16203: Set self_test_no_autoclear flag

The ADIS16201 does not automatically clear the self test flag bit the self
test has been, so clear it manually. Otherwise we'll see a offset caused by
the self-test bias on the output values during normal operation.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:adis16201: Set self_test_no_autoclear flag

The ADIS16201 does not automatically clear the self test flag bit the self
test has been, so clear it manually. Otherwise we'll see a offset caused by
the self-test bias on the output values during normal operation.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adis: Add support for manual self-test flag clear

Some variants of the devices from the ADIS family don't auto-clear the
self-test bit after the self-test has completed. Instead we have to
manually clear. Add support for this to the ADIS library.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: pressure: ms5611: use tab for indention

This fixes the errors reported by checkpatch.pl:

ERROR: code indent should use tabs where possible

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: magnetometer: ak8975: put else and brace at the same line

This fixes the error reported by checkpatch.pl:

ERROR: else should follow close brace '}'

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: common: hid-sensors: use tab for indention

This fixes the error reported by checkpatch.pl:

ERROR: code indent should use tabs where possible

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: common: ms_sensors: use tab for indention

This fixes the error reported by checkpatch.pl:

ERROR: code indent should use tabs where possible

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ad799x: remove space before comma

This fixes the error reported by checkpatch.pl:

ERROR: space prohibited before that ',' (ctx:WxW)

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: at91_adc: fix errors reported by checkpatch.pl

This fixes the errors reported by checkpatch.pl:

ERROR: space prohibited before that ',' (ctx:WxW)
ERROR: code indent should use tabs where possible

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: mcp3422: remove spaces before comma

This fixes the error reported by checkpatch.pl:

ERROR: space prohibited before that ',' (ctx:WxW)

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: vf610_adc: fix case label indent

This fixes the error reported by checkpatch.pl:

ERROR: switch and case should be at the same indent

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: inkern: add a missing space before if

This fixes the error reported by checkpatch.pl:

ERROR: space required before the open parenthesis '('

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: light apds9960: fix wrong use of brace

This fixes the error reported by checkpatch.pl:

ERROR: that open brace { should be on the previous line

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: imu: Add initial support for Bosch BMI160

BMI160 is an Inertial Measurement Unit (IMU) which provides acceleration
and angular rate measurement. It also offers a secondary I2C interface
for connecting a magnetometer sensor (usually BMM160).

Current driver offers support for accelerometer and gyroscope readings
via sysfs or via buffer interface using an external trigger (e.g.
hrtimer). Data is retrieved from IMU via I2C or SPI interface.

Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMI160-DS000-07-786474.pdf

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: dht11: Improve logging

* Unify log messages
* Add more DEBUG messages

Apparently this driver is working unreliably on some platforms that I can't
test. Therefore I want an easy way for bug reporters to provide useful
information without making the driver too chatty by default.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging: iio: ad7606: use iio_device_{claim|release}_direct_mode()

Replace the code that guarantees the device stays in direct mode with
iio_device_{claim|release}_direct_mode() which does same.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: mma7455: use regmap to retrieve struct device

Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.

Patch created using Coccinelle plus manual edits.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs

This patch adds support for the AD5592R (spi) and AD5593R (i2c)
ADC/DAC/GPIO devices.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: mxs-lradc: Move binding document out of staging as well

commit f836c45922446df872250a12dd08e48978aceb2f moved mxs-lradc driver
out of staging. However the binding document was left in the old place.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:magnetometer:ak8975: triggered buffer support

This will be used together with an external trigger (e.g hrtimer based
software trigger).

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: potentiometer: add driver for Maxim Integrated DS1803

The following functions are supported:
 - write, read potentiometer value
 - potentiometer scale

Datasheet: https://datasheets.maximintegrated.com/en/ds/DS1803.pdf

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging: vme: fix bare use of 'unsigned'

fix checkpatch.pl warning about 'Prefer 'unsigned int' to bare use of
'unsigned''

Signed-off-by: Clifton Barnes <clifton.a.barnes@gmail.com>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dgnc: fix CamelCase in dgnc_tty.c

fix checkpatch.pl warning about 'Avoid CamelCase'

Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dgnc: remove too many traverse pointer

The "ch->ch_bd" is already assined to "bd" but this is only
for checking null or MAGIC number.
in the dgnc_tty_ioctl function, bd can be used for referencing
to board_ops structure.

Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

android,lowmemorykiller: Don't abuse TIF_MEMDIE.

Currently, lowmemorykiller (LMK) is using TIF_MEMDIE for two purposes.
One is to remember processes killed by LMK, and the other is to
accelerate termination of processes killed by LMK.

But since LMK is invoked as a memory shrinker function, there still
should be some memory available. It is very likely that memory
allocations by processes killed by LMK will succeed without using
ALLOC_NO_WATERMARKS via TIF_MEMDIE. Even if their allocations cannot
escape from memory allocation loop unless they use ALLOC_NO_WATERMARKS,
lowmem_deathpending_timeout can guarantee forward progress by choosing
next victim process.

On the other hand, mark_oom_victim() assumes that it must be called with
oom_lock held and it must not be called after oom_killer_disable() was
called. But LMK is calling it without holding oom_lock and checking
oom_killer_disabled. It is possible that LMK calls mark_oom_victim()
due to allocation requests by kernel threads after current thread
returned from oom_killer_disabled(). This will break synchronization
for PM/suspend.

This patch introduces per a task_struct flag for remembering processes
killed by LMK, and replaces TIF_MEMDIE with that flag. By applying this
patch, assumption by mark_oom_victim() becomes true.

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Arve Hjonnevag <arve@android.com>
Cc: Riley Andrews <riandrews@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-4.7a' of git://git./linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First round of IIO new device support, features and cleanups for the 4.7 cycle.

New core support
* UV light modifier (for intensity)
* UV light index channel type.

New device support
* hp206c barometer and altimeter
  - new driver.
* mcp4131 potentiometer
  - new driver supporting lots of parts from Microchip.
* mma8452
  - FXLS8471Q support
- NXP LPC18XX SOC ADC
  - new driver.
- NXP LPC18XX SOC DAC
  - new driver.
- rockchip_saradc
  - support rk3399
* st accel
  - h3lis331dl support

Staging driver removals
* adis16204
  - obsolete part making it hard to get parts to test the driver in order
    to clean it up.
* adis16220
  - obsolete part making it hard to get the parts test the driver in order
    to clean it up.

Features
* core
  - convenience functions to claim / release direct access to the device.
    Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
  - power regulator support.
* at91-sama5d2
  - differential channel support.
* mma8452
  - runtime pm support
  - drop device specific autosleep and use the runtime pm one instead.
* ms5611
  - DT bindings
  - oversampling ratio support

Cleanups and minor fixes
* MAINTAINERS
  - Peter got married - hence name change!

* Documentation
  - Fix a typo in in_proximity_raw description.
  - Add some missing docs for iio_buffer_access_funcs.

* Tools
  - update iio_event_monitor names to match new stuff.
  - make generic_buffer look for triggers ending in -trigger as we let these in
  for a number of drivers a long time back and now it is a fairly common
  option.

Drivers
* staging wide
  - convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
  - since boiler plate gpio handling of interrupts has been moved into the
   ACPI core we don't need to include gpio/consumer.h in a load of drivers so
   drop it.
* ad7606
  - fix an endian casting sparse warning.
* ak8975
  - fix a possible unitialized warning from gcc.
  - drop and unused field left over from earlier cleanups
  - fix a missing regulator_disable on exit.
* at91-sama5d2
  - typo and indentation
  - missing IOMEM dependency.
  - cleanup mode register usage by avoidling erasing whole thing when changing
  the sampling frequency.
* bmc150
  - use the core demux and available_scan_masks to simplify buffer handling
  - optimize the transfers in the trigger handler now we have a magic function
  to emulate bulk reads (under circumstances met here).  This matters with some
  rather dumb i2c adapters in particular.
  - use a single regmap_conf for all bus types as they were all the same.
* bmg160
  - use the core demux and available_scan_masks to simplify the buffer handling
  - optimize the transfers in the trigger handler now we have a magic funciton
  to emulate bulk rads (under circumstances met here).
  - drop gpio interrupt probing from the driver (ACPI) as now handled by the
  ACPI core.
* ina2xx-adc
  - update the CALIB register when RShunt changes.
  - fix scale for VShunt - in reality this error canceled out when used.
* isl29028
  - use regmap to retrieve the struct device instead of carrying a second
  copy of it around.
* kxcjk-1013
  - use core demux
  - optimize i2c transfers in the trigger handler.
* mcp4531
  - refactor to use a pointer to access model parameters instead of indexing
    into the array each time.
* mma8452
  - style fixes
  - avoid swtiching to active whenever the config changes
  - add missin i2c_device_id for mma8451
* mpu6050
  - fix possible NULL dereference.
  - fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
  - fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
  - drop gpio interrupt handling for ACPI case from driver as the core now
  handles this case.
* st-sensors
  - note that there are only ever a maximum of 3 axis on current st-sensors
  so just allocate a fixed sized buffer big enough for that.
* tpl0102
  - change the i2c_check_functionality condition to bring it inline with other
    IIO users as EOPNOTSUPP.
* tsl2563
  - replace deprecated flush_scheduled_work

iio: accel: bmc150: use common definition for regmap conf

bmc150_i2c_regmap_conf is defined three times (in bmc150-accel-core.c,
bmc150-accel-i2c.c and and bmc150-accel-spi.c), although the
definition is the same.

Use one common definition for bmc150_i2c_regmap_conf in all
included files.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

hp206c: Initial support for reading sensor values

Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Add channel for UV index

UV index indicating strength of sunburn-producing ultraviolet (UV) radiation

Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Add modifier for UV light

Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: ina2xx-adc: fix scale for VShunt

The scale would result in uV instead of expected mV.
Mostly cosmetic, since the value of 'Power' was computed OK.

Signed-off-by: Marc Titinger <marc.titinger@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc:at91-sama5d2: add support for differential conversions

Add signed differential channels and update the voltage scale for
differential conversions.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc:at91-sama5d2: cleanup mode register use

Do not erase previous configuration of the mode register when setting
the sampling frequency.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: potentiometer: add driver for Microchip MCP413X/414X/415X/416X/423X/424X/425X/426X

The following functionalities are supported:
 - write, read from volatile memory

Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/22060b.pdf

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Reviewed-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Staging: iio: ad7606: Fix sparse endian warning

Fix following sparse warning:
warning: cast to restricted __be16

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: buffer: add missing descriptions in iio_buffer_access_funcs

The members buffer_group and attrs of iio_buffer_access_funcs have no
descriptions for the documentation. Adding them.

Fixes: 08e7e0adaa17 ("iio: buffer: Allocate standard attributes in the core")
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: tools: make generic_buffer look for "-trigger"

All the ST Sensors use the old "<foo>-trigger" rather than the
standard "<foo>-devN" new standard suffix for triggers. Now much
to do about it since it is ABI, but make the testing tools
recognize it too.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: remove gpio interrupt probing from drivers that use a single interrupt

Commit 845c877009cf014b ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.

Commit 0f0796509c07c1c7 ("iio: remove gpio interrupt probing from drivers
that use a single interrupt") removes gpio interrupt probing from most
drivers. This patch cleans the remaining ones.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: remove unused gpio consumer.h include

GPIO handling code has been removed from the drivers (since
this is now handled by the ACPI core) in commit 0f0796509c07 ("iio:
remove gpio interrupt probing from drivers that use a single interrupt").

Remove the include for linux/gpio/consumer.h since it is no longer
used.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: kxcjk-1013: optimize i2c transfers in trigger handler

Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.

When reading data in the trigger handler, the kxcjk-1013 accel driver
does one i2c transfer for each axis. This has an impact on the
frequency of the accelerometer at high sample rates due to additional
delays introduced by the i2c bus at each transfer.

Reading all axis values in one i2c transfer reduces the delays
introduced by the i2c bus. Uses i2c_smbus_read_i2c_block_data_or_emulated
that will fallback to reading each axis as a separate word in case i2c
block read is not supported.

Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: kxcjk-1013: use available_scan_masks

Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.

Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: bmg160: optimize transfers in trigger handler

Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.

When reading data in the trigger handler, the bmg160 gyro driver does
one bus transfer for each axis. This has an impact on the frequency
of the accelerometer at high sample rates due to additional delays
introduced by the bus at each transfer.

Reading all axis values in one bus transfer reduces the delays
introduced by the bus.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: gyro: bmg160: use available_scan_masks

Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: bmc150: optimize transfers in trigger handler

Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.

When reading data in the trigger handler, the bmc150 accel driver does
one bus transfer for each axis. This has an impact on the frequency
of the accelerometer at high sample rates due to additional delays
introduced by the bus at each transfer.

Reading all axis values in one bus transfer reduces the delays
introduced by the bus.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: accel: bmc150: use available_scan_masks

Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: potentiometer: mcp4531: use pointer to access model parameters

Use const pointer to element from model configuration array rather then array
index, as it will not change anyway.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging: dgnc: clean up dgnc_input function

This is for fixing checkpatch.pl warning about
"Alignment should match open parenthesis" but if that is
fixed, code line is over 80 characters.
I think "ch->ch_rqueue + tail + i" could be declared once in
the begining of loop.

Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dgnc: remove useless variables for saving tty's

It doesn't need to save major number with variable.
And there are no use of these variables(dgnc_serial_major and
dgnc_transparent_print_major)

Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: unisys: visorbus: remove unnecessary poll_count logic

The use of poll_count is a vestige from long-ago testing, which is no
longer needed.  It is removed by this patch.

Signed-off-by: Tim Sell <Timothy.Sell@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: libcfs: delete linux-mem.h

The header linux-mem.h is no longer needed.

Signed-off-by: James Simmons <uja.ornl@gmail.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6245
Reviewed-on: http://review.whamcloud.com/13841
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: libcfs: move NUM_CACHEPAGES to libcfs_prim.h

We don't really need linux specific headers anymore so move
NUM_CACHEPAGES macro to libcfs_prim.h.

Signed-off-by: James Simmons <uja.ornl@gmail.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6245
Reviewed-on: http://review.whamcloud.com/13841
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: libcfs: remove MMSPACE macros

Another abstraction that is not needed.

Signed-off-by: James Simmons <uja.ornl@gmail.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6245
Reviewed-on: http://review.whamcloud.com/13841
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: libcfs: remove page_index() macro

Just use the index field directly for struct page.

Signed-off-by: James Simmons <uja.ornl@gmail.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6245
Reviewed-on: http://review.whamcloud.com/13841
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: libcfs: move memory_pressure functions to libcfs_prim.h

Long ago libcfs_prim.h was used for userland code which is why
memory_pressure_*() handling is in both libcfs_prim.h and
linux-mem.h headers. So lets just move the memory_pressure_*()
to libcfs_prim.h.

Signed-off-by: James Simmons <uja.ornl@gmail.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6245
Reviewed-on: http://review.whamcloud.com/13841
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: libcfs: move add_wait_queue_exclusive_head to lustre layer

Only lustre client uses add_wait_queue_exclusive_head() so move
it from libcfs layer to lustre_lib.h where it is needed.

Signed-off-by: James Simmons <uja.ornl@gmail.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6245
Reviewed-on: http://review.whamcloud.com/13874
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: lov_io_init() should return error code

lov_io_init_empty/release() should returns error code instead of
true on error case.

Fault IO needs to handle restart in the case of accessing HSM released
file

Signed-off-by: Bobi Jam <bobijam.xu@intel.com>
Reviewed-on: http://review.whamcloud.com/17240
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7446
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ldlm: Solve a race for LRU lock cancel

This patch solves a race condition that the lock may be used again
after LRU cancellation policy check. In that case, the lock may have
locked or dirty pages that makes the policy check totally useless.
The problem is solved by checking l_last_used at cancellation time
therefore it can make sure that the lock has not been used.

Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Vitaly Fertman <vitaly_fertman@xyratex.com>
Reviewed-on: http://review.whamcloud.com/12603
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5781
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Fix spacing style before open parenthesis

This fixes the remaining occurences of checkpatch warnings
of the form of
WARNING: space prohibited between function name and open parenthesis '('

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ldlm: restore the ELC for enqueue

after LU-4300 enqueue does not ELC anymore, however if enqueue is
agressive (ls -la of a large dir) we may exceed lru-resize limit
quickly because LRUR shrinker and recalc are called not so often.

ELC is to be restored in enqueue.
ELC also should check for the lock weight, in addition to LRUR.
ELC can also keep "skipped" locks, i.e. once checked for the weight
and left in the lru - let LRUR take care about them later.
LRUR is to be left untouched, no weight logic, otherwise LU-5727
appears and OPEN locks do not get canceled.

Xyratex-bug-id: MRP-2550
Signed-off-by: Vitaly Fertman <vitaly.fertman@seagate.com>
Reviewed-on: http://review.whamcloud.com/14342
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6390
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Niu Yawei <yawei.niu@intel.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ldlm: revert changes to ldlm_cancel_aged_policy()

The changes to ldlm_cancel_aged_policy() introduced from LU-4300
was incorrect. This patch revert this part of changes.

Signed-off-by: Niu Yawei <yawei.niu@intel.com>
Reviewed-on: http://review.whamcloud.com/12448
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5727
Reviewed-by: Bobi Jam <bobijam@gmail.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ldlm: ELC picks locks in a safer policy

Change the policy of ELC to pick locks that have no dirty pages,
no page in writeback state, and no locked pages.

Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/9175
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-4300
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Bobi Jam <bobijam@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Remove unused vui_local_lock field

vvp_io_setattr_lock is the only user that sets it, but it's
never checked anywhere, so could go away.
Also get rid of enum ccc_setattr_lock_type that becomes unused.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Move several declarations to llite_internal.h

Move several declarations between llite_internal.h and vvp_internal.h
with the goal of reserving the latter header for functions that
pertain to vvp_{device,object,page,...}.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/13714
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Move ll_dirent_type_get and make it static

ll_dirent_type_get is only used in one place in llite/dir.c,
so move it there.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Remove ccc_global_{init, fini}()

Merge their contents into vvp_global_{init,fini}() and
{init,exit}_lustre_lite().
Rename ccc_inode_fini_* to cl_inode_fini_*.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/13714
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: rename struct ccc_thread_info to vvp_thread_info

struct ccc_thread_info is used in the VVP parts of llite so rename
it struct vvp_thread_info. Rename supporting functions accordingly.
Move init code from lcommon_cl.c to vvp_dev.c

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/13714
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Rename struct vvp_thread_info to ll_thread_info

struct vvp_thread_info is used in the non-VVP parts of llite so rename
it struct ll_thread_info. Rename supporting functions accordingly.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/13714
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Rename struct ccc_grouplock to ll_grouplock

And move the definition from vvp_internal.h to llite_internal.h.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/13714
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: rename ccc_req to vvp_req

Rename struct ccc_req to struct vvp_req and move related functions
from lustre/llite/lcommon_cl.c to the new file lustre/llite/vvp_req.c.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13377
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: move vvp_io functions to vvp_io.c

Move all vvp_io related functions from lustre/llite/lcommon_cl.c to
the sole file where they are used lustre/llite/vvp_io.c.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13376
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: use vui prefix for struct vvp_io members

Rename members of struct vvp_io to used to start with vui_ rather than
cui_.  Rename several instances of struct vvp_io * from cio to vio.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13363
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: merge ccc_io and vvp_io

Move the contents of struct vvp_io into struct ccc_io, delete the
former, and rename the latter to struct vvp_io. Rename various ccc_io
related functions to use vvp rather than ccc.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13351
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre:llite: remove struct ll_ra_read

Ever since removal of the the unused function ll_ra_read_get(),
the struct ll_ra_read members lrr_reader and lrr_linkage and
the struct ll_readahead_state member ras_read_beads unnecessary
so remove them.
In struct vvp_io replace the struct ll_ra_read cui_bead member with
cui_ra_start and cui_ra_count.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13347
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: rename ccc_lock to vvp_lock

Rename struct ccc_lock to struct vvp_lock and merge the CCC lock
methods into the VVP lock methods.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13088
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: rename ccc_page to vvp_page

Rename struct ccc_page to struct vvp_page and remove obsolete CCC page
methods.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13086
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: rename ccc_object to vvp_object

Rename struct ccc_object to struct vvp_object and merge the CCC object
methods into the VVP object methods.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13077
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: rename ccc_device to vvp_device

Rename struct ccc_device to struct vvp_device and merge the CCC device
methods into the VVP device methods.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/13075
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: merge lclient.h into llite/vvp_internal.h

Move the definition of struct cl_client_cache to
lustre/include/cl_object.h and move the rest of
lustre/include/lclient.h in to lustre/llite/vvp_internal.h.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/12592
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5971
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: make sure we do cl_page_clip on the last page

When we are doing a partial IO on both first and last page,
the logic currently only call cl_page_clip on the first page, which
will end up with a incorrect i_size.

Signed-off-by: Li Dongyang <dongyang.li@anu.edu.au>
Reviewed-on: http://review.whamcloud.com/11630
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5552
Reviewed-by: Ian Costello <costello.ian@gmail.com>
Reviewed-by: Niu Yawei <yawei.niu@intel.com>
Reviewed-by: Li Xi <pkuelelixi@gmail.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: deadlock for page write

Writing thread already locked page #1, and then wait for the
Writeback bit of page #2;

Ptlrpc thread is composing a write RPC, so it sets Writeback on
page #2 and tries to lock page #1 to make it ready.

Deadlocked.

Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/9036
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-4540
Reviewed-by: wangdi <di.wang@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: clip page correctly for vvp_io_commit_sync

The original code was wrong which clipped page incorrectly for
partial pages started with zero.

Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/8531
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-4201
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: wangdi <di.wang@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: update comments after cl_lock simplification

Update comments to reflect current cl_lock situations.

Signed-off-by: Bobi Jam <bobijam.xu@intel.com>
Reviewed-on: http://review.whamcloud.com/13137
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6046
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/clio: cl_lock simplification

In this patch, the cl_lock cache is eliminated. cl_lock is turned
into a cacheless data container for the requirements of locks to
complete the IO. cl_lock is created before I/O starts and destroyed
when the I/O is complete.

cl_lock depends on LDLM lock to fulfill lock semantics. LDLM lock
is attached to cl_lock at OSC layer. LDLM lock is still cacheable.

Two major methods are supported for cl_lock: clo_enqueue and
clo_cancel.  A cl_lock is enqueued by cl_lock_request(), which will
call clo_enqueue() methods for each layer to enqueue the lock.
At the LOV layer, if a cl_lock consists of multiple sub cl_locks,
each sub locks will be enqueued correspondingly. At OSC layer, the
lock enqueue request will tend to reuse cached LDLM lock; otherwise
a new LDLM lock will have to be requested from OST side.

cl_lock_cancel() must be called to release a cl_lock after use.
clo_cancel() method will be called for each layer to release the
resource held by this lock. At OSC layer, the reference count of LDLM
lock, which is held at clo_enqueue time, is released.

LDLM lock can only be canceled if there is no cl_lock using it.

Signed-off-by: Bobi Jam <bobijam.xu@intel.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/10858
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3259
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/clio: generalize cl_sync_io

To make cl_sync_io interfaces not just wait for pages, but to be
a generic synchronization mechanism.

Also remove cl_io_cancel that became not used.

Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/8656
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-4198
Reviewed-by: Bobi Jam <bobijam@gmail.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Remove struct ll_iattr

This was a compat code from the time it had ia_attr_flags.
Instead convert all the cryptic callers that did
((struct ll_iattr *)&op_data->op_attr)->ia_attr_flags into
direct access to op_data->op_attr_flags

This also makes lustre/include/linux/obd.h not needed anymore,
so remove it.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: remove some cl wrappers

In llite remove the wrapper functions and macros:
  cl_i2info()
  cl_i2sbi()
  cl_iattr2fd()
  cl_inode_info
  cl_inode_mode()
  cl_inode_{a,m,c}time()
  cl_isize_{read,write,write_nolock}()

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/12850
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-2675
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>