bna: make ethtool_ops and strings const

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xgmac: cleanups

Make local function static, make ethtool_ops const.
Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: make ethtool_ops const

Auditing all usage of ethtool_ops found several drivers that
are not declaring the struct const when it should be.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3" make ethtool ops const

All tables of function pointers should be const to make hacks
more difficult. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netback: make ops structs const

All tables of function pointers should be const to make hacks
more difficult. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net: Pass gfp flags when allocating rx buffers.

Currently, the refill path for RX buffers will always allocate the
buffers as GFP_ATOMIC, even if we are in process context.  This will
fail to apply memory pressure as the worker thread will not contribute
to the freeing of memory.

Fix this by changing add_recvbuf_small to use the gfp variant allocator,
__netdev_alloc_skb_ip_align().

Signed-off-by: Mike Waychison <mikew@google.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: FCoE: Add support for ndo_get_fcoe_hbainfo() call

This patch implements support for ndo_get_fcoe_hbainfo()
call in the ixgbe driver.

This function will be called by the FCoE protocol stack to
obtain device specific information from the underlying
device configured to do FCoE.

Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev: FCoE: Add new ndo_get_fcoe_hbainfo() call

This adds a new ndo_get_fcoe_hbainfo() call in
net_device_ops for FCoE protocol stack.

If supported by the underlying device, the FCoE protocol
stack will call this to get device specific information
from the underlying device.
This information will then be utilized by the FCoE protocol
stack to register Fiber Channel HBA attributes with the
Fiber Channel Management Service via Fabric Device
Management Interface (FDMI) as per the T11 FC-GS
specification.

Changes in v2:
- As per comments from David Miller aligning the parameters
of the ndo_get_fcoe_hbainfo()

Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: reset PHY after recovering from PHY power down

According to 82576_Datasheet.pdf, PHY setting is lost after PHY power down.
So resetting PHY is needed when recovering from PHY power down to set a default
setting to PHY register.
Owing to this lack, NIC doesn't link up in some rare situation.

Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: add basic runtime PM support

Use the runtime power management framework to add basic runtime PM support
to the igb driver. Namely, make the driver suspend the device when the link
is off and set it up for generating a wakeup event after the link has been
detected again. This feature is disabled by default.

Based on e1000e's runtime PM code.

Changes since v1:
Don't suspend the device when shutting down the interface.
Avoid race between runtime suspending and ethtool operations.

Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Add support for byte queue limits.

This adds support for byte queue limits (BQL)

Since this driver collects bytes count in 'bytecount' field, use it also
in igb_tx_map()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: cleanup CE4100 MDIO registers access

A global variable is currently used to hold the virtual address of the
CE4100 MDIO base register address. Store the address in the e1000_hw
structure and update macros accordingly.

Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: unmap ce4100_gbe_mdio_base_virt in e1000_remove

We are not unmapping ce4100_gbe_mdio_base_virt in exit path in case
we are running on a CE4100 adapter, fix that.

Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: fix lockdep splat in shutdown handler

As reported by Steven Rostedt, e1000 has a lockdep splat added
during the recent merge window.  The issue is that
cancel_delayed_work is called while holding our private mutex.

There is no reason that I can see to hold the mutex during pci
shutdown, it was more just paranoia that I put the mutex_lock
around the call to e1000_down.

In a quick survey lots of drivers handle locking differently when
being called by the pci layer.  The assumption here is that we
don't need the mutexes' protection in this function because
the driver could not be unloaded while in the shutdown handler
which is only called at reboot or poweroff.

Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
drivers/net/wireless/b43legacy/dma.c

ath6kl: revert USB support

The ath6kl driver is causing build failures when the ath6kl bits are
not built as modules.  A better fix is forthcoming in a future release,
but for now lets revert the problematic code.

This reverts the following commits:

fde57764ef8751b9aca11b6f6221ac5555bda699
d70385a26ad9a122a5450d066550470107b6bc38
59d954dda4b9b3f3e61d4b87a2b26952b8c4c09d

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge git://git./linux/kernel/git/davem/net

mwl8k: Changing the driver version to 0.13

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Linux 3.2

Merge git://git./linux/kernel/git/davem/net

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  fix CAN MAINTAINERS SCM tree type
  mwifiex: fix crash during simultaneous scan and connect
  b43: fix regression in PIO case
  ath9k: Fix kernel panic in AR2427 in AP mode
  CAN MAINTAINERS update
  net: fsl: fec: fix build for mx23-only kernel
  sch_qfq: fix overflow in qfq_update_start()
  Revert "Bluetooth: Increase HCI reset timeout in hci_dev_do_close"

minixfs: misplaced checks lead to dentry leak

bitmap size sanity checks should be done *before* allocating ->s_root;
there their cleanup on failure would be correct.  As it is, we do iput()
on root inode, but leak the root dentry...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: ensure JOBCTL_STOP_SIGMASK is not zero after detach

This is the temporary simple fix for 3.2, we need more changes in this
area.

1. do_signal_stop() assumes that the running untraced thread in the
   stopped thread group is not possible. This was our goal but it is
   not yet achieved: a stopped-but-resumed tracee can clone the running
   thread which can initiate another group-stop.

   Remove WARN_ON_ONCE(!current->ptrace).

2. A new thread always starts with ->jobctl = 0. If it is auto-attached
   and this group is stopped, __ptrace_unlink() sets JOBCTL_STOP_PENDING
   but JOBCTL_STOP_SIGMASK part is zero, this triggers WANR_ON(!signr)
   in do_jobctl_trap() if another debugger attaches.

   Change __ptrace_unlink() to set the artificial SIGSTOP for report.

   Alternatively we could change ptrace_init_task() to copy signr from
   current, but this means we can copy it for no reason and hide the
   possible similar problems.

Acked-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org> [3.1]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: partially fix the do_wait(WEXITED) vs EXIT_DEAD->EXIT_ZOMBIE race

Test-case:

int main(void)
{
int pid, status;

pid = fork();
if (!pid) {
for (;;) {
if (!fork())
return 0;
if (waitpid(-1, &status, 0) < 0) {
printf("ERR!! wait: %m\n");
return 0;
}
}
}

assert(ptrace(PTRACE_ATTACH, pid, 0,0) == 0);
assert(waitpid(-1, NULL, 0) == pid);

assert(ptrace(PTRACE_SETOPTIONS, pid, 0,
PTRACE_O_TRACEFORK) == 0);

do {
ptrace(PTRACE_CONT, pid, 0, 0);
pid = waitpid(-1, NULL, 0);
} while (pid > 0);

return 1;
}

It fails because ->real_parent sees its child in EXIT_DEAD state
while the tracer is going to change the state back to EXIT_ZOMBIE
in wait_task_zombie().

The offending commit is 823b018e which moved the EXIT_DEAD check,
but in fact we should not blame it. The original code was not
correct as well because it didn't take ptrace_reparented() into
account and because we can't really trust ->ptrace.

This patch adds the additional check to close this particular
race but it doesn't solve the whole problem. We simply can't
rely on ->ptrace in this case, it can be cleared if the tracer
is multithreaded by the exiting ->parent.

I think we should kill EXIT_DEAD altogether, we should always
remove the soon-to-be-reaped child from ->children or at least
we should never do the DEAD->ZOMBIE transition. But this is too
complex for 3.2.

Reported-and-tested-by: Denys Vlasenko <vda.linux@googlemail.com>
Tested-by: Lukasz Michalik <lmi@ift.uni.wroc.pl>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org> [3.0+]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git.samba.org/sfrench/cifs-2.6

* git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] default ntlmv2 for cifs mount delayed to 3.3
  cifs: fix bad buffer length check in coalesce_t2

ipv6/addrconf: speedup /proc/net/if_inet6 filling

This ensures a linear behaviour when filling /proc/net/if_inet6 thus making
ifconfig run really fast on IPv6 only addresses. In fact, with this patch and
the IPv4 one sent a while ago, ifconfig will run in linear time regardless of
address type.

IPv4 related patch: f04565ddf52e401880f8ba51de0dff8ba51c99fd
 dev: use name hash for dev_seq_ops
 ...

Some statistics (running ifconfig > /dev/null on a different setup):

iface count / IPv6 no-patch time / IPv6 patched time / IPv4 time
----------------------------------------------------------------
      6250  |       0.23 s       |      0.13 s       |  0.11 s
     12500  |       0.62 s       |      0.28 s       |  0.22 s
     25000  |       2.91 s       |      0.57 s       |  0.46 s
     50000  |      11.37 s       |      1.21 s       |  0.94 s
    128000  |      86.78 s       |      3.05 s       |  2.54 s

Signed-off-by: Mihai Maruseac <mmaruseac@ixiacom.com>
Cc: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: place comments before code

checkpatch.pl complained about the line exceding 80 columns, and the
comment was actually on the same line as the code, fix that.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: use __aligned(size)

instead of __attribute__((__aligned(size)__))

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: use definitions for MAC_SM register read/writes

Bit 1 is the reset bit of the MAC status machine register, define and
use it.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: use MAC_RST bit definition with MCR1 read/writes

MAC_RST bit is already defined, use it instead of 0x1 where applicable.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: define more MCR0 register bits

Define more MCR0-register bits and use them in place of the bits values.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: remove unused variables and definitions

Since the conversion to phylib (3831861b: r6040: implement phylib) some
PHY-related variables and definitions are now useless, remove them.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040: use an unique MDIO bus name

We should use an unique MDIO bus name which does not clash with anything
else in the system like the Fixed MDIO bus. The bus is now named:
r6040-<card number> which is unique in the system.

Reported-by: Vladimir Kolpakov <vova.kolpakov@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Check RA for sllao when configuring optimistic ipv6 address (v2)

Recently Dave noticed that a test we did in ipv6_add_addr to see if we next hop
route for the interface we're adding an addres to was wrong (see commit
7ffbcecbeed91e5874e9a1cfc4c0cbb07dac3069).  for one, it never triggers, and two,
it was completely wrong to begin with.  This test was meant to cover this
section of RFC 4429:

3.3 Modifications to RFC 2462 Stateless Address Autoconfiguration

   * (modifies section 5.5) A host MAY choose to configure a new address
        as an Optimistic Address.  A host that does not know the SLLAO
        of its router SHOULD NOT configure a new address as Optimistic.
        A router SHOULD NOT configure an Optimistic Address.

This patch should bring us into proper compliance with the above clause.  Since
we only add a SLAAC address after we've received a RA which may or may not
contain a source link layer address option, we can pass a pointer to that option
to addrconf_prefix_rcv (which may be null if the option is not present), and
only set the optimistic flag if the option was found in the RA.

Change notes:
(v2) modified the new parameter to addrconf_prefix_rcv to be a bool rather than
a pointer to make its use more clear as per request from davem.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac80211: remove dead code

ieee80211_offchannel_enable_all_ps function is no longer used
and looks like its logic is extensively handled in
ieee80211_offchannel_stop_vifs

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Recover from firmware crash

In case of firmware crash, reload the firmware and reconfigure it
by triggering ieee80211_hw_restart; mac80211 utility function.

V2 Addressed following comments from Lennert:
 - Stop the queues during reload
 - Removed atomic_t declaration for hw_restart
 - Extend the firmware reload support for sta firmware as well
 - Other misc changes

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Call driver commands after drv_start in mac80211 restart code

Ideally, hardware/firmware initialization is complete after the
drv_start routine. In mac80211 restart code (ieee80211_reconfig),
defer calling the driver commands i.e. setup fragmentation
threshold, rts threshold and coverage class till drv_start
routine is called.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
v2: Removed extra blank line added.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: tx queue enable is read only for EDMA chipsets

for EDMA chip AR_Q_TXE (tx enable for each queue) is read only

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Change RF3853 to RF3053.

According to the latest Ralink vendor drivers, this seems to be the real
RF chipset type.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: RT3593 is also applicable to USB.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00usb: Zero USB padding before sending URB

When USB driver requires padding at the end of frame or URB it will report
this need by increasing return value of get_tx_data_len callback. Common
USB code uses that return value as desired URB length.

Ensure that appropriate part of skb's tailroom exists and is zeroed.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
--
 drivers/net/wireless/rt2x00/rt2x00usb.c |   16 +++++++++++++---
 1 files changed, 13 insertions(+), 3 deletions(-)
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: Let rt2x00usb handle USB padding

Older USB drivers does not append end padding to skb but instead report
it in size of data to be transmitted to HW. rt2800usb should follow that
behaviour. Custom write_tx_data callback which was adding pad to skb
is not be needed any more.

Thanks to this patch frames handed back from rt2800usb to mac80211 will
no longer contain end padding.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Convert big if-statements to switch-statements.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Whitespace cleanup.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Identify rt2800usb chipsets.

According to the latest USB ID database these are all RT2770 / RT2870 / RT307x
devices.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: move checksum and txseq into subfunctions

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: Move ID out of unknown

Testing on the openSUSE wireless forum has shown that a Linksys
WUSB54GC v3 with USB ID 1737:0077 works with rt2800usb when the ID is
written to /sys/.../new_id. This ID can therefore be moved out of UNKNOWN.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: use RCU read locks for sta_info_get

this is being recently introduced by the commit
a85e1d55974646a442d95911e3f7d7a891ea9ac5

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2x00: remove reset_port functionality

Removes reset_port since it isn't used anywhere as suggested by Johannes Berg.

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix kernel panic in IBSS due to a regression

kernel panic occurs when we create an IBSS mode and leave it for
sometime without any joiner and this is introduced by the
commit ec2b774e7c91094d8c00de579646f1162b87b01e where we don't
put proper braces for 'list_for_each_entry_safe' and we pass an
invalid 'sta' pointer to __sta_info_destroy

EIP is at __list_add+0xe/0xa0
EAX: f3b63db4 EBX: 00000000 ECX: eab88c1c EDX: 00000000
ESI: 00000000 EDI: 00000246 EBP: f3b63d80 ESP: f3b63d58
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process kworker/u:2 (pid: 198, ti=f3b62000 task=f3afbea0
task.ti=f3b62000)
Stack:
00000000 00000000 f9ef9821 00000000 00000000 eab88c30
f3b63d80 c017f623
eab88bf0 eab88bf0 f3b63dd0 c066f925 00000000 00000002
00000000 f9ef9821
f3b63da0 c0180a2b eab88c1c eab88c30 00000002 f3afbea0
eab88bf4 f3b63db4
 Call Trace:
[<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60
[mac80211]
[<c017f623>] ? debug_mutex_add_waiter+0x23/0x60
[<c066f925>] __mutex_lock_common+0xd5/0x390
[<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60
[mac80211]
[<c0180a2b>] ? trace_hardirqs_off+0xb/0x10
[<c066fd37>] mutex_lock_nested+0x47/0x60
[<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60
[mac80211]
[<f9ef9821>] __ieee80211_stop_tx_ba_session+0x31/0x60
[mac80211]
[<f9ef8989>] ieee80211_sta_tear_down_BA_sessions+0x39/0x60 [mac80211]
[<f9ef1a67>] __sta_info_destroy+0x57/0x780 [mac80211]
[<f9ef2223>] ieee80211_sta_expire+0x93/0xb0 [mac80211]
[<f9efc8f6>] ieee80211_ibss_work+0x2d6/0x530 [mac80211]

Cc: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix scan state machine

when we run high bandwidth UDP traffic and we trigger a scan, the scan
state machine seems to be looping in SUSPEND->RESUME->DECISION->SUSPEND
and SET_CHANNEL seems to be never called as 'tx_empty' is never true
while running UDP traffic. fix this by settting SET_CHANNEL state when
we get into RESUME state.

Cc: Leela Kella <leela@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/rfkill/rfkill-gpio.c: introduce missing kfree

Error handling code following a kmalloc should free the allocated data.
The label fail_alloc already does this for rfkill.

A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)

// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
x->f1
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: increase tx status ring buffer size

AR9003 chips read tx status from ring buffer whose max number of
status descriptor is mininal compared to max number of tx buffers.
On a stress condition, it can be easily overflown which might cause
false tx hung detection. Though increasing number of max status
descriptors consumes more memory, it helps to avoid false positive
chip resets.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: 3945: fix hw passive scan on radar channels

Patch fix firmware error on "iw dev wlan0 scan passive" for
hardware scanning (with disable_hw_scan=0 module parameter).

 iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
 iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
 iwl3945 0000:03:00.0: Start IWL Error Log Dump:
 iwl3945 0000:03:00.0: Status: 0x0002A2E4, count: 1
 iwl3945 0000:03:00.0: Desc       Time       asrtPC blink2 ilink1  nmiPC   Line
 iwl3945 0000:03:00.0: SYSASSERT     (0x5) 0041263900 0x13756 0x0031C 0x00000 764
 iwl3945 0000:03:00.0: Error Reply type 0x000002FC cmd C_SCAN (0x80) seq 0x443E ser 0x00340000
 iwl3945 0000:03:00.0: Command C_SCAN failed: FW Error
 iwl3945 0000:03:00.0: Can't stop Rx DMA.

We have disable ability to change passive scanning to active on
particular channel when traffic is detected on that channel. Otherwise
firmware will report error, when we try to do passive scan on radar
channels.

Reported-and-debugged-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: 3945: simplify calculations of retry limit

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: random 3945-rs.c cleanups

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: 4965: remove one il4965_hdl_beacon

We have two such functions.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: 3945: get rid of hw_{set,get}_rate

Remove these helpers, some are not unused at all, one can be
unrolled in place of use.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: 4965: small tx_cmd build cleanup

Get rid of two inline functions related and simplify a bit
rts_retry_limit calculations.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: 4965: toggle tx antenna inline

Make function static and change antenna number inline.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: move some i/o helpers out of inline

This save us about 20k of text size, and should have no impact on
performance as hot paths do not use much I/O.

Before:
   text    data     bss     dec     hex filename
 108512    1784     168  110464   1af80 drivers/net/wireless/iwlegacy/iwl3945.ko
 165730    2164     156  168050   29072 drivers/net/wireless/iwlegacy/iwl4965.ko
  91942     328      48   92318   1689e drivers/net/wireless/iwlegacy/iwlegacy.ko

After:
   text    data     bss     dec     hex filename
  95556    1784     168   97508   17ce4 drivers/net/wireless/iwlegacy/iwl3945.ko
 154853    2164     156  157173   265f5 drivers/net/wireless/iwlegacy/iwl4965.ko
  91634     328      48   92010   1676a drivers/net/wireless/iwlegacy/iwlegacy.ko

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: off by one in iwl3945_hw_build_tx_cmd_rate()

We use "rate_index" like this:
rate = iwl3945_rates[rate_index].plcp;
The iwl3945_rates[] array has IWL_RATE_COUNT_3945 elements so the
limit here is off by one.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: remove iwl-sta.c

I forgot to remove this file before.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: always clear SDATA_STATE_OFFCHANNEL flag

If the vif is stopped while it is offchannel (e.g. right
after p2p negotiation) the SDATA_STATE_OFFCHANNEL flag
is never get cleared, resulting in various bad effects
(e.g. GO can't start beaconing).

Fix it by clearing the SDATA_STATE_OFFCHANNEL flag
even if the vif is stopped.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: Treat IPv6 diffserv the same as IPv4 for 802.11e

Wireless will select a different hardware queue based on the
top 3 bits of the diffserv field, for ipv4. Extend that queue
selection mechanism to ipv6, and make the calls orthogonal.

Signed-off-by: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Export a new attribute nfcid1 in target info

The nfcid1 is the NFC-A identifier.
It is exported as an attribute of the target info
(returned as a response to NFC_CMD_GET_TARGET).

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Mark active channel's survey data as "in use"

This is just a cosmetical fix since we only return survey data for the
active channel but it allows iw to show that the survey data is
for the currently used channel.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43legacy: Avoid packet losses in the dma worker code

This patch addresses a bug in the dma worker code that keeps draining
packets even when the hardware queues are full. In such cases packets
can not be passed down to the device and are erroneusly dropped by the
code. It is based on commit bad6919469662b7c92bc6353642aaaa777b36bac,
which fixes the same problem in b43.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix typo in TX power fix

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix controling RF override

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: update gain ctl workarounds

Specs were updated, now we match wl according to MMIO dumps.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: add lacking boardflags defines

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: make ath_mci_duty_cycle static

This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/ath9k/mci.c
drivers/net/wireless/ath/ath9k/mci.c:23:4: warning: symbol 'ath_mci_duty_cycle' was not declared. Should it be static?

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/iwlwifi: use dma_zalloc_coherent() for DMA allocation

Replace dma_alloc_coherent()+memset() with the new dma_zalloc_coherent()

Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: get idle TSSI values

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix success condition of running samples

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: move common TX/RX functions

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: relicense reg.c reg.h and genregdb.awk to ISC

Following the tradition we have had with ath5k, ath9k, CRDA,
wireless-regdb I'd like to license this code under the permissive ISC
license for the code sharing purposes with other OSes, it'd sure be nice
to help the landscape in this area. Although I am %82.89 owner of the
regulatory code I have asked every contributor to the regulatory code
and have receieved positive Acked-bys from everyone except two deceased
entities:

 o Frans Pop RIP 2010 [0]
- Frans Pop <elendil@planet.nl>
- Frans Pop <fjp@debian.org>
 o Nokia     RIP February, 11, 2011 [1], [2]
- ext-yuri.ershov@nokia.com
- kalle.valo@nokia.com

Frans Pop's contribution was a simple patch 55f98938, titled,
"wireless: remove trailing space in messages" which just add a \n
to some printk lines. I'm going to treat these additions as
uncopyrightable.

As for the contributions made by employees on behalf of Nokia
my contact point was Petri Karhula <petri.karhula@nokia.com> but
after one month he noted he had not been able to get traction from the
legal department on this request, as such it I proceeded by replacing
their contributions in previous patches.

The end goal is to help a clean rewrite that starts in userspace
that is shared under ISC license which currently is taking place with
the regulatory simulator [3].

[0] http://lists.debian.org/debian-devel/2011/12/msg00263.html
[1] http://press.nokia.com/2011/02/11/nokia-outlines-new-strategy-introduces-new-leadership-operational-structure/
[2] http://NokiaPlanB.com
[3] git://github.com/mcgrof/regsim.git

Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mihai Moldovan <ionic@ionic.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tony Vroon <tony@linx.net>
Acked-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Pat Erley <pat-lkml@erley.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Joe Perches <joe@perches.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: John Gordon <john@devicescape.com>
Acked-by: Simon Barber <protocolmagic@gmail.com>
Acked-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Jiri Benc <jbenc@upir.cz>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Scott James Remnant <keybuk@google.com>
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: replace reg.c Nokia commit 269ac5

Nokia hasn't gotten back to me in over 1 month for a relicense
change request. There are only a few changes that they contributed,
so just reverting their changes but replacing with another set.
This change replaces this commit:

commit 269ac5fd2d75b118d76a2291e28796527db2f3f8
Author: Kalle Valo <kalle.valo@nokia.com>
Date:   Tue Dec 1 10:47:15 2009 +0200

    cfg80211: indent regulatory messages with spaces

    The regulatory messages in syslog look weird:

    kernel: cfg80211: Regulatory domain: US
    kernel: ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    kernel: ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
    kernel: ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    kernel: ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    kernel: ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    kernel: ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    kernel: ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)

    Indent them with four spaces instead of the tab character to get prettier
    output.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
    Acked: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Petri Karhula <petri.karhula@nokia.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: replace reg.c Nokia commit c4c32294

Nokia hasn't gotten back to me in over 1 month for a relicense
change request. There are only a few changes that they contributed,
so just reverting their changes but replacing with another set.
This change replaces this commit:

commit c4c322941ce0d7e2b7b8794ad70683123d9cb26a
Author: Yuri Ershov <ext-yuri.ershov@nokia.com>
Date:   Tue Jun 29 15:08:08 2010 +0400

    cfg80211: Update of regulatory request initiator handling

    In some cases there could be possible dereferencing freed pointer. The
    update is intended to avoid this issue.

Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Petri Karhula <petri.karhula@nokia.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix sparse complaint on ar9003_switch_com_spdt_get()

This fixes this sparse complaint:

make C=2 CF="-D__CHECK_ENDIAN__" M=drivers/net/wireless/ath/

  CHECK   drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21:    expected restricted __le32 [usertype] val
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21:    got restricted __le16 [usertype] switchcomspdt
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21:    expected restricted __le32 [usertype] val
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21:    got restricted __le16 [usertype] switchcomspdt

The eep->modalHeader5G.switchcomspdt is a le16 and we return u16,
so just return le16_to_cpu().

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: avoid sparse warnings on tracing

Just skip the sparse checks on tracing.

  CHECK   drivers/net/wireless/ath/ath5k/base.c
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1: error: incompatible types for operation (<)
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1:    left side has type struct ath5k_hw *<noident>
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1:    right side has type int
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1: error: incompatible types for operation (<)
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1:    left side has type struct ath5k_hw *<noident>
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1:    right side has type int
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1: error: incompatible types for operation (<)
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1:    left side has type struct ath5k_hw *<noident>
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1:    right side has type int
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
  CC [M]  drivers/net/wireless/ath/ath5k/base.o

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix tx queue sparse complaint

This fixes this rant from sparse:

  CHECK   drivers/net/wireless/ath/ath9k/xmit.c
drivers/net/wireless/ath/ath9k/xmit.c:107:13: warning: context imbalance in 'ath_txq_lock' - wrong count at exit
drivers/net/wireless/ath/ath9k/xmit.c:112:13: warning: context imbalance in 'ath_txq_unlock' - unexpected unlock
drivers/net/wireless/ath/ath9k/xmit.c:123:30: warning: context imbalance in 'ath_txq_unlock_complete' - unexpected unlock
  CC [M]  drivers/net/wireless/ath/ath9k/xmit.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix sparse warnings on ar9003_rtt.c

This fixes these sparse warnings:

  CHECK   drivers/net/wireless/ath/ath9k/ar9003_rtt.c
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:36:6: warning: symbol 'ar9003_hw_rtt_enable' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:41:6: warning: symbol 'ar9003_hw_rtt_disable' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:46:6: warning: symbol 'ar9003_hw_rtt_set_mask' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:52:6: warning: symbol 'ar9003_hw_rtt_force_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:102:6: warning: symbol 'ar9003_hw_rtt_load_hist' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:135:6: warning: symbol 'ar9003_hw_rtt_fill_hist' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:143:6: warning: symbol 'ar9003_hw_rtt_clear_hist' was not declared. Should it be stati

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Handle error during NCI data exchange

Add support for NCI Interface Error Notification.
When this notification is received and we're during a
data exchange transaction, indicate an error to the NFC
core layer via the data exchange callback.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Update names and structs to NCI spec 1.0 d22

Addition, deletion, and modification of NCI constants.
Changes in NCI commands, responses, and notifications structures.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: Protect regdomain change by mutex

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Remove superfluous ieee80211_rx_h_remove_qos_control

This seems to not serve any purpose anymore, at least all frame
processing afterwards seems to be able to deal with QoS frames. So,
let's save the expensive memmove and just leave the QoS header in the
802.11 frame for further processing.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net_sched: sfq: always randomize hash perturbation

SFQ q->perturbation is used in sfq_hash() as an input to Jenkins hash.

We currently randomize this 32bit value only if a perturbation timer is
setup.

Its much better to always initialize it to defeat attackers, or else
they can predict very well what kind of packets they have to forge to
hit a particular flow.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: sfq: fix mem alloc error recovery

Since commit 817fb15dfd98 (net_sched: sfq: allow divisor to be a
parameter), we can leave perturbation timer armed if a memory allocation
error aborts sfq_init().

Memory containing active struct timer_list is freed and kernel can
crash.

Call sfq_destroy() from sfq_init() to properly dismantle qdisc.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: Remove ethtool_ops::set_rx_ntuple operation

All implementations have been converted to implement set_rxnfc
instead.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Remove now-unused filter function

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Implement ethtool RX NFC rules API instead of n-tuple API

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Add support for retrieving and removing filters by ID

These new functions will support an implementation of the ethtool
RX NFC rules API.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Use consistent types for filter IDs, indices and search depths

Filter IDs are u32 (but never very large) so an ID/error return
value should have type s32.

Filter indices and search depths are never negative, so should
have type unsigned int.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Change filter ID generation to satisfy priority semantics of RX NFC

Also add note that the efx_filter_spec::priority field has nothing
to do with priority between multiple matching filters.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: Allow drivers to select RX NFC rule locations

Define special location values for RX NFC that request the driver to
select the actual rule location.  This allows for implementation on
devices that use hash-based filter lookup, whereas currently the API is
more suited to devices with TCAM lookup or linear search.

In ethtool_set_rxnfc() and the compat wrapper ethtool_ioctl(), copy
the structure back to user-space after insertion so that the actual
location is returned.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: Reject out-of-range RX NFC locations

Currently the driver only uses location values to maintain an ordered
list of filters.  Make it reject location values >= MAX_FILER_IDX
passed to the ETHTOOL_SRXCLSRLINS command, consistent with the range
it reports for the ETHTOOL_GRXCLSRLALL command.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Sebastian Pöhn <sebastian.poehn@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless into for-davem

Revert "rtc: Expire alarms after the time is set."

This reverts commit 93b2ec0128c431148b216b8f7337c1a52131ef03.

The call to "schedule_work()" in rtc_initialize_alarm() happens too
early, and can cause oopses at bootup

Neil Brown explains why we do it:

  "If you set an alarm in the future, then shutdown and boot again after
   that time, then you will end up with a timer_queue node which is in
   the past.

   When this happens the queue gets stuck.  That entry-in-the-past won't
   get removed until and interrupt happens and an interrupt won't happen
   because the RTC only triggers an interrupt when the alarm is "now".

   So you'll find that e.g.  "hwclock" will always tell you that
   'select' timed out.

   So we force the interrupt work to happen at the start just in case."

and has a patch that convert it to do things in-process rather than with
the worker thread, but right now it's too late to play around with this,
so we just revert the patch that caused problems for now.

Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Requested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Requested-by: John Stultz <john.stultz@linaro.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[CIFS] default ntlmv2 for cifs mount delayed to 3.3

Turned out the ntlmv2 (default security authentication)
upgrade was harder to test than expected, and we ran
out of time to test against Apple and a few other servers
that we wanted to.  Delay upgrade of default security
from ntlm to ntlmv2 (on mount) to 3.3.  Still works
fine to specify it explicitly via "sec=ntlmv2" so this
should be fine.

Acked-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>