ixgbe: fix ethtool loopback diagnostic with DCB enabled

This patch disables DCB prior to running the loopback test.
When DCB is enabled the frames may be modified on Tx (by adding vlan tag)
which will fail the check on Rx.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: fully disable hardware RSC logic when disabling RSC

This patch modifies the configure_rx path in order to properly disable RSC
hardware logic when the user disables it. Previously we only disabled RSC in the
queue settings, but this does not fully disable hardware RSC logic which can
lead to some unexpected performance issues.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net/mlx4_en: Check device state when setting coalescing

When the device is down, CQs are freed. We must check the device state
to avoid issuing firmware commands on non existing CQs.

CC: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Clamp forward_delay when enabling STP

At some point limits were added to forward_delay.  However, the
limits are only enforced when STP is enabled.  This created a
scenario where you could have a value outside the allowed range
while STP is disabled, which then stuck around even after STP
is enabled.

This patch fixes this by clamping the value when we enable STP.

I had to move the locking around a bit to ensure that there is
no window where someone could insert a value outside the range
while we're in the middle of enabling STP.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>

resubmit bridge: fix message_age_timer calculation

This changes the message_age_timer calculation to use the BPDU's max age as
opposed to the local bridge's max age.  This is in accordance with section
8.6.2.3.2 Step 2 of the 802.1D-1998 sprecification.

With the current implementation, when running with very large bridge
diameters, convergance will not always occur even if a root bridge is
configured to have a longer max age.

Tested successfully on bridge diameters of ~200.

Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: tulip: remove deprecated IRQF_DISABLED

This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/dec/tulip/de4x5.c

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet: amd: remove deprecated IRQF_DISABLED

This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/amd/sun3lance.c

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: remove deprecated IRQF_DISABLED

This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/ibm/ehea/ehea_main.c

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bfin_mac: remove deprecated IRQF_DISABLED

This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/adi/bfin_mac.c.

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netback: count number required slots for an skb more carefully

When a VM is providing an iSCSI target and the LUN is used by the
backend domain, the generated skbs for direct I/O writes to the disk
have large, multi-page skb->data but no frags.

With some lengths and starting offsets, xen_netbk_count_skb_slots()
would be one short because the simple calculation of
DIV_ROUND_UP(skb_headlen(), PAGE_SIZE) was not accounting for the
decisions made by start_new_rx_buffer() which does not guarantee
responses are fully packed.

For example, a skb with length < 2 pages but which spans 3 pages would
be counted as requiring 2 slots but would actually use 3 slots.

skb->data:

    |        1111|222222222222|3333        |

Fully packed, this would need 2 slots:

    |111122222222|22223333    |

But because the 2nd page wholy fits into a slot it is not split across
slots and goes into a slot of its own:

    |1111        |222222222222|3333        |

Miscounting the number of slots means netback may push more responses
than the number of available requests.  This will cause the frontend
to get very confused and report "Too many frags/slots".  The frontend
never recovers and will eventually BUG.

Fix this by counting the number of required slots more carefully.  In
xen_netbk_count_skb_slots(), more closely follow the algorithm used by
xen_netbk_gop_skb() by introducing xen_netbk_count_frag_slots() which
is the dry-run equivalent of netbk_gop_frag_copy().

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Expand led off fix to include 5720

Commit 989038e217e94161862a959e82f9a1ecf8dda152 ("tg3: Don't turn off
led on 5719 serdes port 0") added code to skip turning led off on port
0 of the 5719 since it powered down other ports. This workaround needs
to be enabled on the 5720 as well.

Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sctp: fix ipv6 ipsec encryption bug in sctp_v6_xmit

Alan Chester reported an issue with IPv6 on SCTP that IPsec traffic is not
being encrypted, whereas on IPv4 it is. Setting up an AH + ESP transport
does not seem to have the desired effect:

SCTP + IPv4:

  22:14:20.809645 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 116)
    192.168.0.2 > 192.168.0.5: AH(spi=0x00000042,sumlen=16,seq=0x1): ESP(spi=0x00000044,seq=0x1), length 72
  22:14:20.813270 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 340)
    192.168.0.5 > 192.168.0.2: AH(spi=0x00000043,sumlen=16,seq=0x1):

SCTP + IPv6:

  22:31:19.215029 IP6 (class 0x02, hlim 64, next-header SCTP (132) payload length: 364)
    fe80::222:15ff:fe87:7fc.3333 > fe80::92e6:baff:fe0d:5a54.36767: sctp
    1) [INIT ACK] [init tag: 747759530] [rwnd: 62464] [OS: 10] [MIS: 10]

Moreover, Alan says:

  This problem was seen with both Racoon and Racoon2. Other people have seen
  this with OpenSwan. When IPsec is configured to encrypt all upper layer
  protocols the SCTP connection does not initialize. After using Wireshark to
  follow packets, this is because the SCTP packet leaves Box A unencrypted and
  Box B believes all upper layer protocols are to be encrypted so it drops
  this packet, causing the SCTP connection to fail to initialize. When IPsec
  is configured to encrypt just SCTP, the SCTP packets are observed unencrypted.

In fact, using `socat sctp6-listen:3333 -` on one end and transferring "plaintext"
string on the other end, results in cleartext on the wire where SCTP eventually
does not report any errors, thus in the latter case that Alan reports, the
non-paranoid user might think he's communicating over an encrypted transport on
SCTP although he's not (tcpdump ... -X):

  ...
  0x0030: 5d70 8e1a 0003 001a 177d eb6c 0000 0000  ]p.......}.l....
  0x0040: 0000 0000 706c 6169 6e74 6578 740a 0000  ....plaintext...

Only in /proc/net/xfrm_stat we can see XfrmInTmplMismatch increasing on the
receiver side. Initial follow-up analysis from Alan's bug report was done by
Alexey Dobriyan. Also thanks to Vlad Yasevich for feedback on this.

SCTP has its own implementation of sctp_v6_xmit() not calling inet6_csk_xmit().
This has the implication that it probably never really got updated along with
changes in inet6_csk_xmit() and therefore does not seem to invoke xfrm handlers.

SCTP's IPv4 xmit however, properly calls ip_queue_xmit() to do the work. Since
a call to inet6_csk_xmit() would solve this problem, but result in unecessary
route lookups, let us just use the cached flowi6 instead that we got through
sctp_v6_get_dst(). Since all SCTP packets are being sent through sctp_packet_transmit(),
we do the route lookup / flow caching in sctp_transport_route(), hold it in
tp->dst and skb_dst_set() right after that. If we would alter fl6->daddr in
sctp_v6_xmit() to np->opt->srcrt, we possibly could run into the same effect
of not having xfrm layer pick it up, hence, use fl6_update_dst() in sctp_v6_get_dst()
instead to get the correct source routed dst entry, which we assign to the skb.

Also source address routing example from 625034113 ("sctp: fix sctp to work with
ipv6 source address routing") still works with this patch! Nevertheless, in RFC5095
it is actually 'recommended' to not use that anyway due to traffic amplification [1].
So it seems we're not supposed to do that anyway in sctp_v6_xmit(). Moreover, if
we overwrite the flow destination here, the lower IPv6 layer will be unable to
put the correct destination address into IP header, as routing header is added in
ipv6_push_nfrag_opts() but then probably with wrong final destination. Things aside,
result of this patch is that we do not have any XfrmInTmplMismatch increase plus on
the wire with this patch it now looks like:

SCTP + IPv6:

  08:17:47.074080 IP6 2620:52:0:102f:7a2b:cbff:fe27:1b0a > 2620:52:0:102f:213:72ff:fe32:7eba:
    AH(spi=0x00005fb4,seq=0x1): ESP(spi=0x00005fb5,seq=0x1), length 72
  08:17:47.074264 IP6 2620:52:0:102f:213:72ff:fe32:7eba > 2620:52:0:102f:7a2b:cbff:fe27:1b0a:
    AH(spi=0x00003d54,seq=0x1): ESP(spi=0x00003d55,seq=0x1), length 296

This fixes Kernel Bugzilla 24412. This security issue seems to be present since
2.6.18 kernels. Lets just hope some big passive adversary in the wild didn't have
its fun with that. lksctp-tools IPv6 regression test suite passes as well with
this patch.

 [1] http://www.secdev.org/conf/IPv6_RH_security-csw07.pdf

Reported-by: Alan Chester <alan.chester@tekelec.com>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tuntap: correctly handle error in tun_set_iff()

Commit c8d68e6be1c3b242f1c598595830890b65cea64a
(tuntap: multiqueue support) only call free_netdev() on error in
tun_set_iff(). This causes several issues:

- memory of tun security were leaked
- use after free since the flow gc timer was not deleted and the tfile
  were not detached

This patch solves the above issues.

Reported-by: Wannes Rombouts <wannes.rombouts@epitech.eu>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netback: fix possible format string flaw

This makes sure a format string cannot accidentally leak into the
kthread_run() call.

Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netpoll: Should handle ETH_P_ARP other than ETH_P_IP in netpoll_neigh_reply

The received ARP request type in the Ethernet packet head is ETH_P_ARP other than ETH_P_IP.

[ Bug introduced by commit b7394d2429c198b1da3d46ac39192e891029ec0f
  ("netpoll: prepare for ipv6") ]

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Read flow control for i350 from correct EEPROM section

Flow control is defined in the four EEPROM sections but the driver only reads
from section 0.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Add additional get_phy_id call for i354 devices

This patch fixes a problem where some ports can fail to initialize on a
cold boot. This patch adds an additional call to read the PHY id for i354
devices in order workaround the hardware problem.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'master-2013-09-09' of git://git./linux/kernel/git/linville/wireless

John W. Linville says:

====================
This is a pull request for a few early fixes for the 3.12 stream.

Alexey Khoroshilov corrects a use-after-free issue on rtl8187 found
by the Linux Driver Verification project.

Arend van Spriel provides a brcmfmac patch to fix a build issue
reported by Randy Dunlap.

Hauke Mehrtens offers a bcma fix to properly account for the storage
width of error code values before checking them.

Solomon Peachy brings a pair of cw1200 fixes to avoid hangs in that
driver with SPI devices.  One avoids transfers in interrupt context,
the other fixes a locking issue.

Stanislaw Gruszka changes the initialization of the rt2800 driver to
avoid a freeze, addressing a bug in the Red Hat bugzilla.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: enforce RX_MULTI_EN for the 8168f.

Same narrative as eb2dc35d99028b698cdedba4f5522bc43e576bd2 ("r8169: RxConfig
hack for the 8168evl.") regarding AMD IOMMU errors.

RTL_GIGA_MAC_VER_36 - 8168f as well - has not been reported to behave the
same.

Tested-by: David R <david@unsolicited.net>
Tested-by: Frédéric Leroy <fredo@starox.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bye, bye, WfW flag

This reverts the Linux for Workgroups thing.  And no, before somebody
asks, we're not doing Linux95.  Not for a few years, at least.

Sure, the flag added some color to the logo, and could have remained as
a testament to my leet gimp skills.  But no.  And I'll do this early, to
avoid the chance of forgetting when I'm doing the actual rc1 release on
the road.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'ecryptfs-3.12-rc1-crypt-ctx' of git://git./linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Two small fixes to the code that initializes the per-file crypto
  contexts"

* tag 'ecryptfs-3.12-rc1-crypt-ctx' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  ecryptfs: avoid ctx initialization race
  ecryptfs: remove check for if an array is NULL

Merge branch 'for-v3.12-fix' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping

Pull DMA-mapping fix from Marek Szyprowski:
 "A build bugfix for the device tree support for reserved memory
  regions.  Due to superfluous include the common code failed to build
  on ARM64 and MIPS architectures.

  The patch that caused the build break has lived at linux-next for
  about two weeks and noone noticed the issue, what convinced me that
  everything was ok"

* 'for-v3.12-fix' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  drivers: of: fix build break if asm/dma-contiguous.h is missing

Merge tag 'for-3.12' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf

Pull dma-buf updates from Sumit Semwal:
 "Yet another small one - dma-buf framework now supports size discovery
  of the buffer via llseek"

* tag 'for-3.12' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
  dma-buf: Expose buffer size to userspace (v2)
  dma-buf: Check return value of anon_inode_getfile

Merge branch 'akpm' (patches from Andrew Morton)

Merge first patch-bomb from Andrew Morton:
 - Some pidns/fork/exec tweaks
 - OCFS2 updates
 - Most of MM - there remain quite a few memcg parts which depend on
   pending core cgroups changes.  Which might have been already merged -
   I'll check tomorrow...
 - Various misc stuff all over the place
 - A few block bits which I never got around to sending to Jens -
   relatively minor things.
 - MAINTAINERS maintenance
 - A small number of lib/ updates
 - checkpatch updates
 - epoll
 - firmware/dmi-scan
 - Some kprobes work for S390
 - drivers/rtc updates
 - hfsplus feature work
 - vmcore feature work
 - rbtree upgrades
 - AOE updates
 - pktcdvd cleanups
 - PPS
 - memstick
 - w1
 - New "inittmpfs" feature, which does the obvious
 - More IPC work from Davidlohr.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (303 commits)
  lz4: fix compression/decompression signedness mismatch
  ipc: drop ipc_lock_check
  ipc, shm: drop shm_lock_check
  ipc: drop ipc_lock_by_ptr
  ipc, shm: guard against non-existant vma in shmdt(2)
  ipc: document general ipc locking scheme
  ipc,msg: drop msg_unlock
  ipc: rename ids->rw_mutex
  ipc,shm: shorten critical region for shmat
  ipc,shm: cleanup do_shmat pasta
  ipc,shm: shorten critical region for shmctl
  ipc,shm: make shmctl_nolock lockless
  ipc,shm: introduce shmctl_nolock
  ipc: drop ipcctl_pre_down
  ipc,shm: shorten critical region in shmctl_down
  ipc,shm: introduce lockless functions to obtain the ipc object
  initmpfs: use initramfs if rootfstype= or root= specified
  initmpfs: make rootfs use tmpfs when CONFIG_TMPFS enabled
  initmpfs: move rootfs code from fs/ramfs/ to init/
  initmpfs: move bdi setup from init_rootfs to init_ramfs
  ...

lz4: fix compression/decompression signedness mismatch

LZ4 compression and decompression functions require different in
signedness input/output parameters: unsigned char for compression and
signed char for decompression.

Change decompression API to require "(const) unsigned char *".

Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Kyungsik Lee <kyungsik.lee@lge.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yann Collet <yann.collet.73@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: drop ipc_lock_check

No remaining users, we now use ipc_obtain_object_check().

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc, shm: drop shm_lock_check

This function was replaced by a the lockless shm_obtain_object_check(),
and no longer has any users.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: drop ipc_lock_by_ptr

After previous cleanups and optimizations, this function is no longer
heavily used and we don't have a good reason to keep it.  Update the few
remaining callers and get rid of it.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc, shm: guard against non-existant vma in shmdt(2)

When !CONFIG_MMU there's a chance we can derefence a NULL pointer when the
VM area isn't found - check the return value of find_vma().

Also, remove the redundant -EINVAL return: retval is set to the proper
return code and *only* changed to 0, when we actually unmap the segments.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: document general ipc locking scheme

As suggested by Andrew, add a generic initial locking scheme used
throughout all sysv ipc mechanisms.  Documenting the ids rwsem, how rcu
can be enough to do the initial checks and when to actually acquire the
kern_ipc_perm.lock spinlock.

I found that adding it to util.c was generic enough.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,msg: drop msg_unlock

There is only one user left, drop this function and just call
ipc_unlock_object() and rcu_read_unlock().

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: rename ids->rw_mutex

Since in some situations the lock can be shared for readers, we shouldn't
be calling it a mutex, rename it to rwsem.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: shorten critical region for shmat

Similar to other system calls, acquire the kern_ipc_perm lock after doing
the initial permission and security checks.

[sasha.levin@oracle.com: dont leave do_shmat with rcu lock held]
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: cleanup do_shmat pasta

Clean up some of the messy do_shmat() spaghetti code, getting rid of
out_free and out_put_dentry labels.  This makes shortening the critical
region of this function in the next patch a little easier to do and read.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: shorten critical region for shmctl

With the *_INFO, *_STAT, IPC_RMID and IPC_SET commands already optimized,
deal with the remaining SHM_LOCK and SHM_UNLOCK commands.  Take the
shm_perm lock after doing the initial auditing and security checks.  The
rest of the logic remains unchanged.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: make shmctl_nolock lockless

While the INFO cmd doesn't take the ipc lock, the STAT commands do acquire
it unnecessarily.  We can do the permissions and security checks only
holding the rcu lock.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: introduce shmctl_nolock

Similar to semctl and msgctl, when calling msgctl, the *_INFO and *_STAT
commands can be performed without acquiring the ipc object.

Add a shmctl_nolock() function and move the logic of *_INFO and *_STAT out
of msgctl().  Since we are just moving functionality, this change still
takes the lock and it will be properly lockless in the next patch.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: drop ipcctl_pre_down

Now that sem, msgque and shm, through *_down(), all use the lockless
variant of ipcctl_pre_down(), go ahead and delete it.

[akpm@linux-foundation.org: fix function name in kerneldoc, cleanups]
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: shorten critical region in shmctl_down

Instead of holding the ipc lock for the entire function, use the
ipcctl_pre_down_nolock and only acquire the lock for specific commands:
RMID and SET.

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: introduce lockless functions to obtain the ipc object

This is the third and final patchset that deals with reducing the amount
of contention we impose on the ipc lock (kern_ipc_perm.lock).  These
changes mostly deal with shared memory, previous work has already been
done for semaphores and message queues:

  http://lkml.org/lkml/2013/3/20/546 (sems)
  http://lkml.org/lkml/2013/5/15/584 (mqueues)

With these patches applied, a custom shm microbenchmark stressing shmctl
doing IPC_STAT with 4 threads a million times, reduces the execution
time by 50%.  A similar run, this time with IPC_SET, reduces the
execution time from 3 mins and 35 secs to 27 seconds.

Patches 1-8: replaces blindly taking the ipc lock for a smarter
combination of rcu and ipc_obtain_object, only acquiring the spinlock
when updating.

Patch 9: renames the ids rw_mutex to rwsem, which is what it already was.

Patch 10: is a trivial mqueue leftover cleanup

Patch 11: adds a brief lock scheme description, requested by Andrew.

This patch:

Add shm_obtain_object() and shm_obtain_object_check(), which will allow us
to get the ipc object without acquiring the lock.  Just as with other
forms of ipc, these functions are basically wrappers around
ipc_obtain_object*().

Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

initmpfs: use initramfs if rootfstype= or root= specified

Command line option rootfstype=ramfs to obtain old initramfs behavior, and
use ramfs instead of tmpfs for stub when root= defined (for cosmetic
reasons).

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

initmpfs: make rootfs use tmpfs when CONFIG_TMPFS enabled

Conditionally call the appropriate fs_init function and fill_super
functions.  Add a use once guard to shmem_init() to simply succeed on a
second call.

(Note that IS_ENABLED() is a compile time constant so dead code
elimination removes unused function calls when CONFIG_TMPFS is disabled.)

Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

initmpfs: move rootfs code from fs/ramfs/ to init/

When the rootfs code was a wrapper around ramfs, having them in the same
file made sense.  Now that it can wrap another filesystem type, move it in
with the init code instead.

This also allows a subsequent patch to access rootfstype= command line
arg.

Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

initmpfs: move bdi setup from init_rootfs to init_ramfs

Even though ramfs hasn't got a backing device, commit e0bf68ddec4f ("mm:
bdi init hooks") added one anyway, and put the initialization in
init_rootfs() since that's the first user, leaving it out of init_ramfs()
to avoid duplication.

But initmpfs uses init_tmpfs() instead, so move the init into the
filesystem's init function, add a "once" guard to prevent duplicate
initialization, and call the filesystem init from rootfs init.

This goes part of the way to allowing ramfs to be built as a module.

[akpm@linux-foundation.org; using bit 1 was odd]
Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

initmpfs: replace MS_NOUSER in initramfs

Mounting MS_NOUSER prevents --bind mounts from rootfs.  Prevent new rootfs
mounts with a different mechanism that doesn't affect bind mounts.

Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/radix-tree.c: make radix_tree_node_alloc() work correctly within interrupt

With users of radix_tree_preload() run from interrupt (block/blk-ioc.c is
one such possible user), the following race can happen:

radix_tree_preload()
...
radix_tree_insert()
  radix_tree_node_alloc()
    if (rtp->nr) {
      ret = rtp->nodes[rtp->nr - 1];
<interrupt>
...
radix_tree_preload()
...
radix_tree_insert()
  radix_tree_node_alloc()
    if (rtp->nr) {
      ret = rtp->nodes[rtp->nr - 1];

And we give out one radix tree node twice.  That clearly results in radix
tree corruption with different results (usually OOPS) depending on which
two users of radix tree race.

We fix the problem by making radix_tree_node_alloc() always allocate fresh
radix tree nodes when in interrupt.  Using preloading when in interrupt
doesn't make sense since all the allocations have to be atomic anyway and
we cannot steal nodes from process-context users because some users rely
on radix_tree_insert() succeeding after radix_tree_preload().
in_interrupt() check is somewhat ugly but we cannot simply key off passed
gfp_mask as that is acquired from root_gfp_mask() and thus the same for
all preload users.

Another part of the fix is to avoid node preallocation in
radix_tree_preload() when passed gfp_mask doesn't allow waiting.  Again,
preallocation in such case doesn't make sense and when preallocation would
happen in interrupt we could possibly leak some allocated nodes.  However,
some users of radix_tree_preload() require following radix_tree_insert()
to succeed.  To avoid unexpected effects for these users,
radix_tree_preload() only warns if passed gfp mask doesn't allow waiting
and we provide a new function radix_tree_maybe_preload() for those users
which get different gfp mask from different call sites and which are
prepared to handle radix_tree_insert() failure.

Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/w1/masters/mxc_w1.c: remove unnecessary platform_set_drvdata()

The driver core clears the driver data to NULL after device_release or on
probe failure.  Thus, it is not needed to manually clear the device driver
data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/w1/w1.c: replace strict_strtol() with kstrtol()

The usage of strict_strtol() is not preferred, because strict_strtol() is
obsolete.  Thus, kstrtol() should be used.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memstick: add support for legacy memorysticks

Based partially on MS standard spec quotes from Alex Dubov.

As any code that works with user data this driver isn't recommended to use
to write cards that contain valuable data.

It tries its best though to avoid data corruption and possible damage to
the card.

Tested on MS DUO 64 MB card on Ricoh R592 card reader.

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/memstick/host/rtsx_pci_ms.c: remove unnecessary platform_set_drvdata()

The driver core clears the driver data to NULL after device_release or on
probe failure.  Thus, it is not needed to manually clear the device driver
data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/pps/clients/pps-gpio.c: remove unnecessary platform_set_drvdata()

The driver core clears the driver data to NULL after device_release or on
probe failure.  Thus, it is not needed to manually clear the device driver
data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: fix defective misuses of pkt_<level>

Fix thinkos where pkt_<level> needs a valid pktcdvd_device * and the
pointer is known to be NULL.

Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> (go smatch!)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: add struct pktcdvd_device * to pkt_dump_sense()

Allow the device name to be emitted with pkt_err when logging the sense
data.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: convert pr_info to pkt_info

Add a new pkt_info macro to prefix the name to the logging output.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: convert pr_notice to pkt_notice

Add a new pkt_notice macro to prefix the name to the logging output.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: add struct pktcdvd_device.name to pr_err logging where possible

Add a new pkt_err macro to prefix the name to the logging output.  Convert
pr_err where there is a non-null struct pktcdvd_device.

Includes improvements from Andy Shevchenko.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: add struct pktcdvd_device * to pkt_dbg

Add pd->name to output for these debugging messages.

Remove normally compiled out pkt_dbg(2, ...) function entry tracing
equivalents as it's better done via the function tracer.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: consolidate DPRINTK and VPRINTK macros

Use the more common pkt_dbg(level, fmt, ...) form.

These messages are emitted at KERN_NOTICE.

Always emit function name with pkt_dbg(2, ...) uses and remove the
sometimes abbreviated embedded function name.

This form always verifies the format and arguments.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: convert printk to pr_<level>

Use a more current logging style and add messages levels to the logging
messages.

Simplify pkt_dump_sense by using %*ph and adding a simple function to emit
the sense string.

Includes improvements from Andy Shevchenko and Dan Carpenter.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pktcdvd: convert ZONE macro to static function get_zone()

Macros should be converted to functions where feasible to
verify arguments and the like.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

panic: call panic handlers before kmsg_dump

Since the panic handlers may produce additional information (via printk)
for the kernel log, it should be reported as part of the panic output
saved by kmsg_dump().  Without this re-ordering, nothing that adds
information to a panic will show up in pstore's view when kmsg_dump runs,
and is therefore not visible to crash reporting tools that examine pstore
output.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

affs: use loff_t in affs_truncate()

It seems pretty unlikely that AFFS supports files over 4GB but we may as
well leave use loff_t just for cleanness sake instead of truncating it to
32 bits.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: remove do-nothing NAME="%k" term from example udev rules

When the example udev rules in the documentation are used without
modification, warnings like the one shown below appear in the system logs:

  /var/log/messages:Aug 22 11:09:11 kung udevd[445]: NAME="%k" \
    is superfluous and breaks kernel supplied names, please remove \
    it from /etc/udev/rules.d/60-aoe.rules:26

Removing the term does not cause any problems with the creation of the
special character and block device nodes.

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: do not BUG if memory pressure prevented debugfs file creation

If the system has trouble allocating memory for the creation of the aoe
debugfs directory or of a file inside it, the debugfs member of an aoedev
can be NULL.

Do not treat a NULL debugfs pointer as a BUG on aoedev shutdown, avoiding
the user impact of an unecessary panic.

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: suppress compiler warnings

This patch fixes following compiler warnings:

  drivers/block/aoe/aoecmd.c: In function `aoecmd_ata_rw':
  drivers/block/aoe/aoecmd.c:383:17: warning: variable `t' set but not used [-Wunused-but-set-variable]
    struct aoetgt *t;
                   ^
  drivers/block/aoe/aoecmd.c: In function `resend':
  drivers/block/aoe/aoecmd.c:488:21: warning: variable `ah' set but not used [-Wunused-but-set-variable]
    struct aoe_atahdr *ah;
                       ^

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: remove custom implementation of kbasename()

In the kernel we have a nice helper that may be used here. This patch
substitutes the custom implementation by the native function call.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: update internal version number to 85

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: update copyright date

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: fill in per-AoE-target information for debugfs file

This information is presented in a compact format that has evolved for
easy routine scanning by expert humans, mostly developers and support
technicians helping to troubleshoot or test AoE-based systems.

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: provide file operations for debugfs files

The place holder in the file contents is filled out in the following
patch.

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: add AoE-target files to debugfs

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: create and destroy debugfs directory for aoe

This series adds the debugging information that the coraid.com-distributed
aoe driver exports via sysfs, but instead of sysfs, it uses debugfs.

With these patches applied, even without AoE targets on the network, KEDR
reports new possible memory leaks, but these are from callers outside the
aoe driver that have used aoe_devnode to get the name of the character
devices through the aoe_class->devnode callback, and I believe they're
responsible for freeing that memory.

This patch:

Create and destroy the debugfs directory.

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/zswap: use postorder iteration when destroying rbtree

Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Reviewed-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rbtree: allow tests to run as builtin

No reason require rbtree test code to be a module, allow it to be builtin
(streamlines my development process)

Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Reviewed-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rbtree_test: add test for postorder iteration

Just check that we examine all nodes in the tree for the postorder
iteration.

Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Reviewed-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rbtree: add rbtree_postorder_for_each_entry_safe() helper

Because deletion (of the entire tree) is a relatively common use of the
rbtree_postorder iteration, and because doing it safely means fiddling
with temporary storage, provide a helper to simplify postorder rbtree
iteration.

Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Reviewed-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rbtree: add postorder iteration functions

Postorder iteration yields all of a node's children prior to yielding the
node itself, and this particular implementation also avoids examining the
leaf links in a node after that node has been yielded.

In what I expect will be its most common usage, postorder iteration allows
the deletion of every node in an rbtree without modifying the rbtree nodes
(no _requirement_ that they be nulled) while avoiding referencing child
nodes after they have been "deleted" (most commonly, freed).

I have only updated zswap to use this functionality at this point, but
numerous bits of code (most notably in the filesystem drivers) use a hand
rolled postorder iteration that NULLs child links as it traverses the
tree.  Each of those instances could be replaced with this common
implementation.

1 & 2 add rbtree postorder iteration functions.
3 adds testing of the iteration to the rbtree runtime tests
4 allows building the rbtree runtime tests as builtins
5 updates zswap.

This patch:

Add postorder iteration functions for rbtree.  These are useful for safely
freeing an entire rbtree without modifying the tree at all.

Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Reviewed-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

block/partitions/efi.c: consistently use pr_foo()

Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: some style cleanups

Trivial coding style cleanups - still plenty left.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: delete annoying emacs style comments

I love emacs, but these settings for coding style are annoying when trying
to open the efi.h file.  More important, we already have checkpatch for
that.

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: compare first and last usable LBAs

When verifying GPT header integrity, make sure that first usable LBA is
smaller than last usable LBA.

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: account for pmbr size in lba

The partition that has the 0xEE (GPT protective), must have the size in
lba field set to the lesser of the size of the disk minus one or
0xFFFFFFFF for larger disks.

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: detect hybrid MBRs

One of the biggest problems with GPT is compatibility with older, non-GPT
systems.  The problem is addressed by creating hybrid mbrs, an extension,
or variant, of the traditional protective mbr.  This contains, apart from
the 0xEE partition, up three additional primary partitions that point to
the same space marked by up to three GPT partitions.  The result is that
legacy OSs can see the three required MBR partitions and at the same time
ignore the GPT-aware partitions that protect the GPT structures.

While hybrid MBRs are hacks, workarounds and simply not part of the GPT
standard, they do exist and we have no way around them.  For instance, by
default, OSX creates a hybrid scheme when using multi-OS booting.

In order for Linux to properly discover protective MBRs, it must be made
aware of devices that have hybrid MBRs.  No functionality is changed by
this patch, just a debug message informing the user of the MBR scheme that
is being used.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: do not require gpt partition to begin at sector 1

When detecting a valid protective MBR, the Linux kernel isn't picky about
the partition (1-4) the 0xEE is at, but, unlike other operating systems,
it does require it to begin at the second sector (sector 1).  This check,
apart from it not being enforced by UEFI, and causing Linux to potentially
fail to detect any *valid* partitions on the disk, can present problems
when dealing with hybrid MBRs[1].

For compatibility reasons, if the first partition is hybridized, the 0xEE
partition must be small enough to ensure that it only protects the GPT
data structures - as opposed to the the whole disk in a protective MBR.
This problem is very well described by Rod Smith[1]: where MBR-only
partitioning programs (such as older versions of fdisk) can see some of
the disk space as unallocated, thus loosing the purpose of the 0xEE
partition's protection of GPT data structures.

By dropping this check, this patch enables Linux to be more flexible when
probing for GPT disklabels.

[1] http://www.rodsbooks.com/gdisk/hybrid.html#reactions

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: check pmbr record's starting lba

Per the UEFI Specs 2.4, June 2013, the starting lba of the partition that
has the EFI GPT (0xEE) must be set to 0x00000001 - this is obviously the
LBA of the GPT Partition Header.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

partitions/efi: use lba-aware partition records

The kernel's GPT implementation currently uses the generic 'struct
partition' type for dealing with legacy MBR partition records.  While this
is is useful for disklabels that we designed for CHS addressing, such as
msdos, it doesn't adapt well to newer standards that use LBA instead, such
as GUID partition tables.  Furthermore, these generic partition structures
do not have all the required fields to properly follow the UEFI specs.

While a CHS address can be translated to LBA, it's much simpler and
cleaner to just replace the partition type.  This patch adds a new
'gpt_record' type that is fully compliant with EFI and will allow, in the
next patches, to add more checks to properly verify a protective MBR,
which is paramount to probing a device that makes use of GPT.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Karel Zak <kzak@redhat.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s390/vmcore: use vmcore for zfcpdump

Modify the s390 copy_oldmem_page() and remap_oldmem_pfn_range() function
for zfcpdump to read from the HSA memory if memory below HSA_SIZE bytes is
requested.  Otherwise real memory is used.

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Willeke <willeke@de.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vmcore: enable /proc/vmcore mmap for s390

The patch "s390/vmcore: Implement remap_oldmem_pfn_range for s390" allows
now to use mmap also on s390.

So enable mmap for s390 again.

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Willeke <willeke@de.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s390/vmcore: implement remap_oldmem_pfn_range for s390

Introduce the s390 specific way to map pages from oldmem.  The memory area
below OLDMEM_SIZE is mapped with offset OLDMEM_BASE.  The other old memory
is mapped directly.

Signed-off-by: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vmcore: introduce remap_oldmem_pfn_range()

For zfcpdump we can't map the HSA storage because it is only available via
a read interface.  Therefore, for the new vmcore mmap feature we have
introduce a new mechanism to create mappings on demand.

This patch introduces a new architecture function remap_oldmem_pfn_range()
that should be used to create mappings with remap_pfn_range() for oldmem
areas that can be directly mapped.  For zfcpdump this is everything
besides of the HSA memory.  For the areas that are not mapped by
remap_oldmem_pfn_range() a generic vmcore a new generic vmcore fault
handler mmap_vmcore_fault() is called.

This handler works as follows:

* Get already available or new page from page cache (find_or_create_page)
* Check if /proc/vmcore page is filled with data (PageUptodate)
* If yes:
  Return that page
* If no:
  Fill page using __vmcore_read(), set PageUptodate, and return page

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s390/vmcore: use ELF header in new memory feature

Exchange the old relocate mechanism with the new arch function call
override mechanism that allows to create the ELF core header in the 2nd
kernel.

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Willeke <willeke@de.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vmcore: introduce ELF header in new memory feature

For s390 we want to use /proc/vmcore for our SCSI stand-alone dump
(zfcpdump).  We have support where the first HSA_SIZE bytes are saved into
a hypervisor owned memory area (HSA) before the kdump kernel is booted.
When the kdump kernel starts, it is restricted to use only HSA_SIZE bytes.

The advantages of this mechanism are:

 * No crashkernel memory has to be defined in the old kernel.
 * Early boot problems (before kexec_load has been done) can be dumped
 * Non-Linux systems can be dumped.

We modify the s390 copy_oldmem_page() function to read from the HSA memory
if memory below HSA_SIZE bytes is requested.

Since we cannot use the kexec tool to load the kernel in this scenario,
we have to build the ELF header in the 2nd (kdump/new) kernel.

So with the following patch set we would like to introduce the new
function that the ELF header for /proc/vmcore can be created in the 2nd
kernel memory.

The following steps are done during zfcpdump execution:

1.  Production system crashes
2.  User boots a SCSI disk that has been prepared with the zfcpdump tool
3.  Hypervisor saves CPU state of boot CPU and HSA_SIZE bytes of memory into HSA
4.  Boot loader loads kernel into low memory area
5.  Kernel boots and uses only HSA_SIZE bytes of memory
6.  Kernel saves registers of non-boot CPUs
7.  Kernel does memory detection for dump memory map
8.  Kernel creates ELF header for /proc/vmcore
9.  /proc/vmcore uses this header for initialization
10. The zfcpdump user space reads /proc/vmcore to write dump to SCSI disk
    - copy_oldmem_page() copies from HSA for memory below HSA_SIZE
    - copy_oldmem_page() copies from real memory for memory above HSA_SIZE

Currently for s390 we create the ELF core header in the 2nd kernel with a
small trick.  We relocate the addresses in the ELF header in a way that
for the /proc/vmcore code it seems to be in the 1st kernel (old) memory
and the read_from_oldmem() returns the correct data.  This allows the
/proc/vmcore code to use the ELF header in the 2nd kernel.

This patch:

Exchange the old mechanism with the new and much cleaner function call
override feature that now offcially allows to create the ELF core header
in the 2nd kernel.

To use the new feature the following function have to be defined
by the architecture backend code to read from new memory:

 * elfcorehdr_alloc: Allocate ELF header
 * elfcorehdr_free: Free the memory of the ELF header
 * elfcorehdr_read: Read from ELF header
 * elfcorehdr_read_notes: Read from ELF notes

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kexec: remove unnecessary return

Code can not run here forever, so remove the unnecessary return.

Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Suggested-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: cleanup the error handling in search_binary_handler()

The error hanling and ret-from-loop look confusing and inconsistent.

- "retval >= 0" simply returns

- "!bprm->file" returns too but with read_unlock() because
   binfmt_lock was already re-acquired

- "retval != -ENOEXEC || bprm->mm == NULL" does "break" and
  relies on the same check after the main loop

Consolidate these checks into a single if/return statement.

need_retry still checks "retval == -ENOEXEC", but this and -ENOENT before
the main loop are not needed.  This is only for pathological and
impossible list_empty(&formats) case.

It is not clear why do we check "bprm->mm == NULL", probably this
should be removed.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Zach Levis <zml@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: don't retry if request_module() fails

A separate one-liner for better documentation.

It doesn't make sense to retry if request_module() fails to exec
/sbin/modprobe, add the additional "request_module() < 0" check.

However, this logic still doesn't look exactly right:

1. It would be better to check "request_module() != 0", the user
   space modprobe process should report the correct exit code.
   But I didn't dare to add the user-visible change.

2. The whole ENOEXEC logic looks suboptimal. Suppose that we try
   to exec a "#!path-to-unsupported-binary" script. In this case
   request_module() + "retry" will be done twice: first by the
   "depth == 1" code, and then again by the "depth == 0" caller
   which doesn't make sense.

3. And note that in the case above bprm->buf was already changed
   by load_script()->prepare_binprm(), so this looks even more
   ugly.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Zach Levis <zml@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: cleanup the CONFIG_MODULES logic

search_binary_handler() uses "for (try=0; try<2; try++)" to avoid "goto"
but the code looks too complicated and horrible imho.  We still need to
check "try == 0" before request_module() and add the additional "break"
for !CONFIG_MODULES case.

Kill this loop and use a simple "bool need_retry" + "goto retry".  The
code looks much simpler and we do not even need ifdef's, gcc can optimize
out the "if (need_retry)" block if !IS_ENABLED().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Zach Levis <zml@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: kill ->load_binary != NULL check in search_binary_handler()

search_binary_handler() checks ->load_binary != NULL for no reason, this
method should be always defined.  Turn this check into WARN_ON() and move
it into __register_binfmt().

Also, kill the function pointer.  The current code looks confusing, as if
->load_binary can go away after read_unlock(&binfmt_lock).  But we rely on
module_get(fmt->module), this fmt can't be changed or unregistered,
otherwise this code is buggy anyway.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Zach Levis <zml@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: move allow_write_access/fput to exec_binprm()

When search_binary_handler() succeeds it does allow_write_access() and
fput(), then it clears bprm->file to ensure the caller will not do the
same.

We can simply move this code to exec_binprm() which is called only once.
In fact we could move this to free_bprm() and remove the same code in
do_execve_common's error path.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Zach Levis <zml@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: proc_exec_connector() should be called only once

A separate one-liner with the minor fix.

PROC_EVENT_EXEC reports the "exec" event, but this message is sent at
least twice if search_binary_handler() is called by ->load_binary()
recursively, say, load_script().

Move it to exec_binprm(), this is "depth == 0" code too.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Zach Levis <zml@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: kill "int depth" in search_binary_handler()

Nobody except search_binary_handler() should touch ->recursion_depth, "int
depth" buys nothing but complicates the code, kill it.

Probably we should also kill "fn" and the !NULL check, ->load_binary
should be always defined.  And it can not go away after read_unlock() or
this code is buggy anyway.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Zach Levis <zml@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>