git.stricted.de - GitHub/LineageOS/android_kernel_motorola

libertas: set mac control synchronously during init

CMD_MAC_CONTROL is currently sent async to the firmware, and is sent
from the lbs_setup_firmware() path during device init.

This means that device init can complete with commands pending, and
the if_sdio driver will sometimes power down the device (after init)
with this command still pending.

This was causing an occasional spurious command timeout after init,
leading to a device reset.

Fix this by making CMD_MAC_CONTROL synchronous when called from the
lbs_setup_firmware() path.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Choose correct LED pin for AR9565

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Rename antenna diversity macros

The register macros for antenna diversity are common for
AR9462 and AR9565, rename them.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Handle gentimer termination properly

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: separate TxPD processing routine for AP

This patch adds separate tx packet descriptor routine for AP
interface. This function fills bss_type, bss_num, wmm packet
delay information etc for TxPD going on AP interface.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: disable WOW by default

Some platforms do not support WOW. Let's change the default wakeup
criteria to 0.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: support custom world regulatory domain

country 00 (world regulatory domain) doesn't define channels
52 - 64 and 100 - 140. Add these channels to our custom world
regulatory domain.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: do not hint regulatory domain with f/w country code

We will use world regulatory domain (country 00) as default
when driver is loaded. Later after a successful association
cfg80211 will change the regulatory domain to a specific country
if the AP has advertised country IE.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use country ie of requested AP while associating

AP's country ie is parsed and 11d information is updated in firmware
while associating. Previous mwifiex_send_domain_info_cmd_fw() call in
association path is not necessary now. Hence it is removed in this
patch.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: update adapter->bss_prio_tbl[j].bss_prio_cur correctly

"adapter->bss_prio_tbl[j].bss_prio_head" points to linked list of
interfaces with priority 'j'. "bss_prio_tbl[j].bss_prio_cur" is
supposed to point to next interface every time the routine for
dequeuing the packet is called. This ensures that each interface
gets fair chance.

Currently we have AP and station interfaces with priority '0'.
Therefore "adapter->bss_prio_tbl[0].bss_prio_cur" should
alternately point to AP and station nodes. Since "bss_prio_cur"
is not correctly updated, for each packet picked for AP, two
packets are picked for station interface.

This patch fixes the problem by correctly updating "bss_prio_cur".

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: have same priority for AP and station traffic

Currently AP interface has higher priority over station. Hence
separate entries are created in "adapter->bss_prio_tbl" for these
interfaces and station packet is dequeued only if there is not
packet in queue for AP. It is observed that ping for station
interface doesn't work if heavy traffic is running on AP.

The problem is fixed by having same priority for both the
interfaces. This patch also removes an extra initialisation
for "priv->bss_priority".

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove AMSDU_AGGR_CTRL command response handler

HostCmd_CMD_AMSDU_AGGR_CTRL is never called with GET action.
So the code in mwifiex_ret_amsdu_aggr_ctrl() becomes redundant.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove 11N_CFG command response handler

HostCmd_CMD_11N_CFG is never called with GET action. So the code in
mwifiex_ret_11n_cfg() becomes redundant.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove get operation code for SUBSCRIBE EVENT command

We don't send this command with GET action. Redundant code in
mwifiex_ret_subsc_evt() is removed in this patch.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add 8 points for 5G temp slop

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: use peak detection for 5GHz

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Wait BT calibration to complete

Whenever BT calibration requested, WLAN has to wait for the
calibration to be completed. But right now we defer the waiting
which might cause BT calibration to fail. Fix that.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: remove pointless check from rndis_scan()

In rndis_scan(), 'request' is actually always valid pointer and
the !request check is unneeded, so remove it.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add PCI ID for AR9565

Enable AR9565.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Program correct PLL value for AR9565

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix spur mitigation for AR9565

Exclude CCK spur mitigation, freq 2437 for OFDM and
add AR9565-specific logic.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Set correct max streams for AR9565

Also, set the correct chainmask.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add AR9565 HW support

Various parts of the code require AR9565 checks,
this patch adds them.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add AR9565 initvals

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add version/revision macros for AR9565

And recognize the device in the init path.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: fix off-by-one null pointer bug in p54_tx_80211

This patch fixes a regression which was introduced in:
"mac80211: move TX station pointer and restructure TX"

IP: p54_tx_80211+0x21/0x513 [p54common]
Oops: 0000 [#1] SMP
Modules linked in: p54usb p54common [...]
Pid: 13394, comm: hostapd 3.6.0-rc4-wl+
RIP: 0010:p54_tx_80211+0x21/0x513
RSP: 0018:... EFLAGS: 00010292
[...]
Process hostapd
Stack:
[...]
Call Trace:
p54_bss_info_changed+0x204/0x21e [p54common]
ieee80211_del_station+0x16/0x32 [mac80211]
ieee80211_start_ap+0x10f/0x157 [mac80211]
nl80211_start_ap+0x315/0x361 [cfg80211]

p54_tx_80211 function is called as part of the
beacon update. The caller p54_bss_info_changed
has to supply a valid tx control struct, or
the control->sta will lead to a null pointer
dereference.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/ar9003_mac.c: removes unnecessary semicolon

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add Generic hardware timer interrupt in debugfs

Having generic hardware timer interrupt in debugfs
would come handy when we are debugging 3 WIRE
BTCOEX issues.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Read and configure thermocal for AR9462

Read and configure thermometer calibration results read from
OTP card.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Read and apply thermometer settings from EEPROM

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/rtlwifi/rtl8192de/phy.c: removes unnecessary semicolon

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: at76c50x: eliminate hex2str()

The hex2str() is substituted by '%*phD' specificator.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Cancel BTCOEX related work before disabling BTCOEX

Before disabling BTCOEX in the h/w cancel all BTCOEX related
works. This is similar to the commit in ath9k(c32cdbd8)
ath9k: Stop the BTCOEX timers before disabling BTCOEX

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add a modparam to enable BTCOEX rather than default

Enable BTCOEX for WB193(which seems to be the only supported
ath9k_htc BTCOEX chipset)only when it is enabled via modparam,
rather than enabling it by default.

Cc: Vivek Natarajan <nataraja@qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: minor cleanup in ath9k_htc_add_station

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Cleanup add/change_interface callbacks

*Remove all the checks that will be handled by cfg80211
based on the interface combination advertised. For instance,
driver supports at the maximum 8 beaconing interface, while
we advertise maximum 8 beaconing interface in the interface
combination support.

*cfg80211 will take care of not allowing
us to add an interface that is not supported by the
driver, further if the change_interface changes the
old interface to a beaconing interface while we had
reached the max limit of 8 beaconing interface, again
cfg80211 takes care of this stuff!
So remove all these checks.

*Beautify placing PS wrappers in the appropriate
position.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove an obselete function declaration

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Make use of ath_stop_ani wrapper

Additionally it has a neat debug message informing us
that we are stopping the ANI algorithm.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix BTCOEX timer triggering comparision

Its more correct to convert btcoex_period to 'us' while
comparing with btcoex_no_stomp which is in 'us'.
Did not find any functionality issues being fixed,
as the generic hardware timer triggers are usually
refreshed with the newer duty cycle.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix invalid MCI GPM index access/caching

There is a possibility that AR_MCI_GPM_1 register can
return 0xdeadbeef and this results in caching of invalid
GPM index in ar9003_mci_is_gpm_valid. Ensure we
have appropriate checks to avoid this.

Cc: xijin luo <xijin@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: Remove bogus memcpy in ai_detach

gcc 4.8 warns for this memcpy. While the copy size is correct, the whole
copy seems to be a nop because the destination is never used, and
there's no need to use memcpy to copy pointers anyways. And the
type of the pointer was wrong, but at least those are always the same.

Just remove it.

/backup/lsrc/git/linux-lto-2.6/drivers/net/wireless/brcm80211/brcmsmac/aiutils.c: In function 'ai_detach':
/backup/lsrc/git/linux-lto-2.6/drivers/net/wireless/brcm80211/brcmsmac/aiutils.c:539:32: warning: argument to 'sizeof' in 'memcpy' call is the same pointer type 'struct si_pub **' as the destination; expected 'struct si_pub *' or an explicit length [-Wsizeof-pointer-memaccess]
memcpy(&si_local, &sih, sizeof(struct si_pub **));
^

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: enable support for MFP

zd1211rw lacks hardware encryption, so enabling 802.11w is only matter of
enabling IEEE80211_HW_MFP_CAPABLE flag.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: add MediaTek/RaLink Rt3352 WiSoC

Support for the RT3352 WiSoC was developed for and tested with the ALL5002
devboard running OpenWrt. For now, this supports only devices with internal
TXALC. Corrections were made according to the remarks of Stanislaw Gruszka and
Gertjan van Wingerde, thank you guys for reviewing!

Signed-off-by: Daniel Golle <dgolle@allnet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800 - Make probe_hw function common between PCI and USB.

Refactor the probe_hw code so that more code can be shared between
rt2800pci and rt2800usb.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Unify GPIO register field namings

The various rt2x00 drivers use different methods to name the different
GPIO register fields indicating the GPIO pin value and the fields
indicating the direction.
Start using a unified naming scheme for the GPIO register fields:
- <csr>_VAL<x> for fields indicating the GPIO pin value.
- <csr>_DIR<x> for fields indicating the GPIO pin direction.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Align GPIO register definitions with the datasheets.

Ensure that all active GPIO pins are included in the GPIO register
definitions, nothing more and nothing less.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

rtlwifi: Update header file

The latest version of the vendor driver for the rtlwifi family
includes many changes. This patch incorporates the difference
in the main header file.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: rtl8192ce: rtl8192cu: rtl8192se: Remove sparse warnings

The rtlwifi family of drivers has the following sparse errors:

  CHECK   drivers/net/wireless/rtlwifi/usb.c
drivers/net/wireless/rtlwifi/usb.c:122:17: warning: cast to restricted __le32
  CHECK   drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:1157:13: warning: context imbalance in 'rtl92c_dm_refresh_rate_adaptive_mask' - different lock contexts for basic block
  CHECK   drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:1909:30: warning: cast to restricted __le32
  CHECK   drivers/net/wireless/rtlwifi/rtl8192ce/sw.c
drivers/net/wireless/rtlwifi/rtl8192ce/sw.c:345:1: warning: symbol 'rtl92ce_pci_ids' was not declared. Should it be static?
  CHECK   drivers/net/wireless/rtlwifi/rtl8192cu/trx.c
drivers/net/wireless/rtlwifi/rtl8192cu/trx.c:494:9: warning: cast from restricted __le16
  CHECK   drivers/net/wireless/rtlwifi/rtl8192se/fw.c
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:490:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:490:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:494:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:494:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:499:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:499:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:510:25: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:510:25: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:607:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:607:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:650:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:650:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:652:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:652:9: warning: cast to restricted __le16
  CHECK   drivers/net/wireless/rtlwifi/rtl8192se/trx.c
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:758:9: warning: cast from restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:788:17: warning: cast from restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:804:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:804:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:807:17: warning: cast from restricted __le32

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: rtl8192de: Fix typo in cursta_connectctate

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: store mwifiex_ds_misc_subsc_evt in mwifiex_private

Since mwifiex_ds_misc_subsc_evt is used in an asynchronous case,
store the structure in the long-lived mwifiex_private instead of
on the calling stack.

This fixes a problem where the response of the asynchronous
operation would corrupt a stack frame potentially in use by
a different thread.

Signed-off-by: Jeff Disher <disher@chromium.org>
Reviewed-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Jeff Disher <disher@chromium.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add callback for nl80211 testmode command

This change adds callback for nl80211 testmode, which can be used
for testing and debugging purposes with driver and firmware.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Add 43143 USB support.

Added usb device id to list of supported devices. 43143 is a new
802.11n single stream device.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Add 43242 USB support.

Added usb device id to list of supported devices. 43242 is the new
802.11n 2x2 MIMO device.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add BCM43241 sdio interface driver support

BCM43241 is an 11abg and 2x2 11n Wifi/BT/FM combo chip that
supports 40MHz channel width. This patch intends to enable
the driver support for the chip through SDIO bus interface.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: prevent possible race condition on usb rx control.

brcmf_usb_tx_ctlpkt sends message using brcmf_usb_send_ctl then
clears boolean and waits for boolean to be set (by another
thread). This can result in situation where flag gets cleared
while result was already received. First clearing the flag and
then sending the data will prevent this.

Reviewed-by: Arend Van Spriel (arend@broadcom.com)
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix TX filter usage

The TX filter bit for a station would be set by the HW
when a frame is not acked. A frame would be completed with
ATH9K_TXERR_FILT status only when the corresponding filter bit
for the destination station is already set.

Currently, un-acknowledged packets are added to the pending queue
and retried, but the "clear_dest_mask" bit in the descriptor is
set only when the TX status has been ATH9K_TXERR_FILT. This results
in packet loss and the log shows:

wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746071
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746076
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746377
...
...

This issue can be resolved by making sure that the destination
mask is cleared when the packet is being retried and the earlier
TX status is ATH9K_TXERR_XRETRY.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: remove pointless conditional before kfree_skb()

Remove pointless conditional before kfree_skb().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: remove pointless conditional before kfree_skb()

Remove pointless conditional before kfree_skb().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: make use of is_zero_ether_addr()

Use is_zero_ether_addr() instead of directly using memcmp() to
determine if the ethernet address is all zeros.

Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: parse rate info for AP

This patch adds support for parsing rates from cfg80211_ap_settings
of start_ap handler. This in turn adds support for 11a and 11b phy
configurations.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: don't disable wait_q_enabled flag

We should not disable "cmd_node->wait_q_enabled" flag here before
calling mwifiex_insert_cmd_to_free_q() because we want to wake up
the thread waiting for command completion inside this function.

The wait_q_enabled flag will be disabled internally upon command
completion.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: release semaphore acquired for internal scan operation

If "iw connect" command is fired for station interface, when
heavy traffic is running on AP interface, internal scan operation
performed before actual association is aborted. In this case we
missed to release semaphore.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: remove duplicated include from airo.c

From: Wei Yongjun <yongjun_wei@trendmicro.com.cn>

Remove duplicated include.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl18xx: remove duplicated include from main.c

From: Wei Yongjun <yongjun_wei@trendmicro.com.cn>

Remove duplicated include.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl3501_cs: use is_broadcast_ether_addr() instead of memcmp()

Using is_broadcast_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is broadcast
address.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: use is_broadcast_ether_addr() instead of memcmp()

Using is_broadcast_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is broadcast
address.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: small optimization

Assign the MCI BT state locally, rather than unnecessarily calling
ar9003_mci_state and updating it.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use is_zero_ether_addr() instead of memcmp()

Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use is_broadcast_ether_addr() instead of memcmp()

Using is_broadcast_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is broadcast
address.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: use is_zero_ether_addr() and is_broadcast_ether_addr()

Using is_zero_ether_addr() and is_broadcast_ether_addr() instead of
directly use memcmp() to determine if the ethernet address is all zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net: use is_zero_ether_addr() instead of memcmp()

Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: use is_zero_ether_addr() instead of memcmp()

Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200: use is_zero_ether_addr() and is_broadcast_ether_addr()

Using is_zero_ether_addr() and is_broadcast_ether_addr() instead of
directly use memcmp() to determine if the ethernet address is all zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2100: use is_zero_ether_addr() and is_broadcast_ether_addr()

Using is_zero_ether_addr() and is_broadcast_ether_addr() instead of
directly use memcmp() to determine if the ethernet address is all zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: ath9k-htc: only load firmware in need

It is not necessary to hold the firmware memory during the whole
driver lifetime, and obviously it does waste memory. Suppose there
are 4 ath9k-htc usb dongles working, kernel has to consume about
4*50KBytes RAM to cache firmware for all dongles. After applying the
patch, kernel only caches one single firmware image in RAM for
all ath9k-htc devices just during system suspend/resume cycle.

When system is ready for loading firmware, ath9k-htc can request
the loading from usersapce. During system resume, ath9k-htc still
can load the firmware which was cached in kernel memory before
system suspend.

Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: don't leak memory for PCIE, MIPS, GBIT cores

bcma_scan_bus allocates a bcma_core for each core found on the bus, but the
memory for cores handled by the bcma driver itself was not being freed when
the bus was unregistered. This patch adds special handling for the PCIE,
MIPS, and GBIT COMMON cores, to ensure that their memory allocation is
freed as well.

Note that this patch doesn't address the memory allocated for the CC core,
as that was corrected in my previous patch "bcma: register cc core driver,
device."

Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Saul St. John <saul.stjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

libertas sdio: fix suspend when interface is down

When the interface is down, the hardware is powered off.
However, the suspend handler currently tries to send host sleep commands
(when wakeup params are set) in this configuration, causing a system hang
when going into suspend (the commands will never complete).

Avoid this by detecting this situation and simply returning from
the suspend handler without doing anything special.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: Added rx packet length validity check

On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.

The fix was tested on the latest compat-wireless-3.5.1-1-snpc.

Cc: stable@vger.kernel.org
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix rfkill polling prior to interface start.

We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.

Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix word size of rt2500usb MAC_CSR19 register.

The register is 16 bits wide, not 32.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Identify ASUS USB-N53 device.

This is an RT3572 based device.

Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix get rssi by clearing getvar struct.

The function brcmf_cfg80211_get_station requests the RSSI from
the device. The complete structure used needs to be cleared
before sending the request to firmware. Otherwise the request
fails filling the logs with "Could not get rssi (-2)" messages.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix race condition for rx and tx data.

On both rx and tx there is was a race condition on the queueing
of usb requests. When for example frame gets submitted it is
possible that complete function gets called even before
usb_submit_urb() returns. As a result it is possible that usb
requests get losts, which was noticed on OMAP4 pandaboard
platform. This patch fixes the race condition.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: dont use ZERO flag for usb IN

URB_ZERO_PACKET should only be set or bulk OUT and this condition
is checked with a WARN_ON in usb_submit_urb(). This patch fixes
brcmfmac to get rid of this warning filling the logs.

Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix use of dev_kfree_skb() in irq context

The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:

Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()

The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix a crash in 2 WIRE btcoex chipsets

Generic timers for BTCOEX functionality is applicable
only for 3 WIRE BTCOEX (and MCI) chipsets.
Hence btcoex->no_stomp_timer is allocated only 3 WIRE
btcoex chipsets and in all the other cases its NULL.
Make sure we stop the generic timer only if
'btcoex->hw_timer_enabled' is true(only if its up and
running)

Fixes the following crash

[68757.020454] BUG: unable to handle kernel NULL pointer dereference at 0000000c
[68757.020916] IP: [<f9b055c3>] ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
[68757.021251] *pde = 00000000
[68757.024384] EIP: 0060:[<f9b055c3>] EFLAGS: 00010082 CPU: 0
[68757.024384] EIP is at ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
[68757.024384] EAX: d32d0000 EBX: d32d0000 ECX: 00000000 EDX: 00000000
[68757.024384] ESI: e67c24c0 EDI: 00000296 EBP: e137be2c ESP: e137be20
[68757.024384]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[68757.024384] CR0: 8005003b CR2: 0000000c CR3: 00b99000 CR4: 000407d0
[68757.024384] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[68757.024384] DR6: ffff0ff0 DR7: 00000400
[68757.024384] Process kworker/u:2 (pid: 8917, ti=e137a000 task=ea7a6860 task.ti=e137a000)
[68757.024384] Stack:
[68757.024384]  c06c4676 d32d0000 e67c24c0 e137be38 f81c9590 e67c1ca0 e137be40 f81c95d9
[68757.024384]  e137be64 f81cd1c5 00000246 00000002 d32d0000 e67c05e0 e67c1ca0 e67c05e0
[68757.024384]  00000000 e137beac f81cdfa0 e137be84 00000246 00000246 e67c1ca0 e67c1ca0
[68757.024384] Call Trace:
[68757.024384]  [<c06c4676>] ? _raw_spin_lock_irqsave+0x86/0xa0
[68757.024384]  [<f81c9590>] ath9k_gen_timer_stop+0x10/0x40 [ath9k]
[68757.024384]  [<f81c95d9>] ath9k_btcoex_stop_gen_timer+0x19/0x20 [ath9k]
[68757.024384]  [<f81cd1c5>] ath9k_ps_restore+0x85/0x110 [ath9k]
[68757.024384]  [<f81cdfa0>] ath9k_config+0x220/0x520 [ath9k]
[68757.024384]  [<f81cd47d>] ? ath9k_flush+0x15d/0x1b0 [ath9k]
[68757.024384]  [<f85c7ca5>] ieee80211_hw_config+0x135/0x2c0 [mac80211]
[68757.024384]  [<f860e3c8>] ieee80211_dynamic_ps_enable_work+0x198/0x5f0 [mac80211]

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: enable PA linearization

This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.

On many newer devices, the calibration is assumed to be done with PA
linearization enabled.

Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix PA linearization calibration related crash

Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: disable PA linearization for AR9462

Support for it is incomplete

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: calibrate PA input for PA predistortion

Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clear the AM2PM predistortion mask on AR933x

That predistortion type is not supported

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: do not enable the MIB interrupt in the interrupt mask register

The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: fix voltage setting for RT3572/RT3592

According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.

Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix skb length issue when send a command to firmware

When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.

Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>