ath10k: Fix tx hanging

[ Upstream commit e8a91863eba3966a447d2daa1526082d52b5db2a ]

While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: synchronize with FW after multicast commands

[ Upstream commit db66abeea3aefed481391ecc564fb7b7fb31d742 ]

If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.

Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported-by: Maximilian Ernestus <maximilian@ernestus.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: m920x: don't use stack on USB reads

[ Upstream commit a2ab06d7c4d6bfd0b545a768247a70463e977e27 ]

Using stack-allocated pointers for USB message data don't work.
This driver is almost OK with that, except for the I2C read
logic.

Fix it by using a temporary read buffer, just like on all other
calls to m920x_read().

Link: https://lore.kernel.org/all/ccc99e48-de4f-045e-0fe4-61e3118e3f74@mida.se/
Reported-by: rkardell@mida.se
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: saa7146: hexium_orion: Fix a NULL pointer dereference in hexium_attach()

[ Upstream commit 348df8035301dd212e3cc2860efe4c86cb0d3303 ]

In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. In hexium_detach(), saa7146_vv_release()
will be called and there is a dereference of dev->vv_data in
saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init() according to the following logic.

Both hexium_attach() and hexium_detach() are callback functions of
the variable 'extension', so there exists a possible call chain directly
from hexium_attach() to hexium_detach():

hexium_attach(dev, info) -- fail to alloc memory to dev->vv_data
|      in saa7146_vv_init().
|
|
hexium_detach() -- a dereference of dev->vv_data in saa7146_vv_release()

Fix this bug by adding a check of saa7146_vv_init().

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_VIDEO_HEXIUM_ORION=m show no new warnings,
and our static analyzer no longer warns about this code.

Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Increase UVC_CTRL_CONTROL_TIMEOUT to 5 seconds.

[ Upstream commit c8ed7d2f614cd8b315981d116c7a2fb01829500d ]

Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.

So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000

It fixes the following runtime warnings:
   Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
   Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).

Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

floppy: Add max size check for user space request

[ Upstream commit 545a32498c536ee152331cd2e7d2416aa0f20e01 ]

We need to check the max request size that is from user space before
allocating pages. If the request size exceeds the limit, return -EINVAL.
This check can avoid the warning below from page allocator.

WARNING: CPU: 3 PID: 16525 at mm/page_alloc.c:5344 current_gfp_context include/linux/sched/mm.h:195 [inline]
WARNING: CPU: 3 PID: 16525 at mm/page_alloc.c:5344 __alloc_pages+0x45d/0x500 mm/page_alloc.c:5356
Modules linked in:
CPU: 3 PID: 16525 Comm: syz-executor.3 Not tainted 5.15.0-syzkaller #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
RIP: 0010:__alloc_pages+0x45d/0x500 mm/page_alloc.c:5344
Code: be c9 00 00 00 48 c7 c7 20 4a 97 89 c6 05 62 32 a7 0b 01 e8 74 9a 42 07 e9 6a ff ff ff 0f 0b e9 a0 fd ff ff 40 80 e5 3f eb 88 <0f> 0b e9 18 ff ff ff 4c 89 ef 44 89 e6 45 31 ed e8 1e 76 ff ff e9
RSP: 0018:ffffc90023b87850 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 1ffff92004770f0b RCX: dffffc0000000000
RDX: 0000000000000000 RSI: 0000000000000033 RDI: 0000000000010cc1
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001
R10: ffffffff81bb4686 R11: 0000000000000001 R12: ffffffff902c1960
R13: 0000000000000033 R14: 0000000000000000 R15: ffff88804cf64a30
FS:  0000000000000000(0000) GS:ffff88802cd00000(0063) knlGS:00000000f44b4b40
CS:  0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: 000000002c921000 CR3: 000000004f507000 CR4: 0000000000150ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 alloc_pages+0x1a7/0x300 mm/mempolicy.c:2191
 __get_free_pages+0x8/0x40 mm/page_alloc.c:5418
 raw_cmd_copyin drivers/block/floppy.c:3113 [inline]
 raw_cmd_ioctl drivers/block/floppy.c:3160 [inline]
 fd_locked_ioctl+0x12e5/0x2820 drivers/block/floppy.c:3528
 fd_ioctl drivers/block/floppy.c:3555 [inline]
 fd_compat_ioctl+0x891/0x1b60 drivers/block/floppy.c:3869
 compat_blkdev_ioctl+0x3b8/0x810 block/ioctl.c:662
 __do_compat_sys_ioctl+0x1c7/0x290 fs/ioctl.c:972
 do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline]
 __do_fast_syscall_32+0x65/0xf0 arch/x86/entry/common.c:178
 do_fast_syscall_32+0x2f/0x70 arch/x86/entry/common.c:203
 entry_SYSENTER_compat_after_hwframe+0x4d/0x5c

Reported-by: syzbot+23a02c7df2cf2bc93fa2@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211116131033.27685-1-sxwjean@me.com
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: uhci: add aspeed ast2600 uhci support

[ Upstream commit 554abfe2eadec97d12c71d4a69da1518478f69eb ]

Enable ast2600 uhci quirks.

Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20211126100021.2331024-1-neal_liu@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mwifiex: Fix skb_over_panic in mwifiex_usb_recv()

[ Upstream commit 04d80663f67ccef893061b49ec8a42ff7045ae84 ]

Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.

The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.

Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
 len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
 tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
 <IRQ>
 ? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
 skb_put.cold+0x24/0x24
 mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
 __usb_hcd_giveback_urb+0x1e4/0x380
 usb_giveback_urb_bh+0x241/0x4f0
 ? __hrtimer_run_queues+0x316/0x740
 ? __usb_hcd_giveback_urb+0x380/0x380
 tasklet_action_common.isra.0+0x135/0x330
 __do_softirq+0x18c/0x634
 irq_exit+0x114/0x140
 smp_apic_timer_interrupt+0xde/0x380
 apic_timer_interrupt+0xf/0x20
 </IRQ>

Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>

HSI: core: Fix return freed object in hsi_new_client

[ Upstream commit a1ee1c08fcd5af03187dcd41dcab12fd5b379555 ]

cl is freed on error of calling device_register, but this
object is return later, which will cause uaf issue. Fix it
by return NULL on error.

Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: acpi: Do not set the IRQ type if the IRQ is already in use

[ Upstream commit bdfd6ab8fdccd8b138837efff66f4a1911496378 ]

If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.

I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.

Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/bridge: megachips: Ensure both bridges are probed before registration

[ Upstream commit 11632d4aa2b3f126790e81a4415d6c23103cf8bb ]

In the configuration used by the b850v3, the STDP2690 is used to read EDID
data whilst it's the STDP4028 which can detect when monitors are connected.

This can result in problems at boot with monitors connected when the
STDP4028 is probed first, a monitor is detected and an attempt is made to
read the EDID data before the STDP2690 has probed:

[    3.795721] Unable to handle kernel NULL pointer dereference at virtual address 00000018
[    3.803845] pgd = (ptrval)
[    3.806581] [00000018] *pgd=00000000
[    3.810180] Internal error: Oops: 5 [#1] SMP ARM
[    3.814813] Modules linked in:
[    3.817879] CPU: 0 PID: 64 Comm: kworker/u4:1 Not tainted 5.15.0 #1
[    3.824161] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[    3.830705] Workqueue: events_unbound deferred_probe_work_func
[    3.836565] PC is at stdp2690_get_edid+0x44/0x19c
[    3.841286] LR is at ge_b850v3_lvds_get_modes+0x2c/0x5c
[    3.846526] pc : [<805eae10>]    lr : [<805eb138>]    psr: 80000013
[    3.852802] sp : 81c359d0  ip : 7dbb550b  fp : 81c35a1c
[    3.858037] r10: 81c73840  r9 : 81c73894  r8 : 816d9800
[    3.863270] r7 : 00000000  r6 : 81c34000  r5 : 00000000  r4 : 810c35f0
[    3.869808] r3 : 80e3e294  r2 : 00000080  r1 : 00000cc0  r0 : 81401180
[    3.876349] Flags: Nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[    3.883499] Control: 10c5387d  Table: 1000404a  DAC: 00000051
[    3.889254] Register r0 information: slab kmem_cache start 81401180 pointer offset 0
[    3.897034] Register r1 information: non-paged memory
[    3.902097] Register r2 information: non-paged memory
[    3.907160] Register r3 information: non-slab/vmalloc memory
[    3.912832] Register r4 information: non-slab/vmalloc memory
[    3.918503] Register r5 information: NULL pointer
[    3.923217] Register r6 information: non-slab/vmalloc memory
[    3.928887] Register r7 information: NULL pointer
[    3.933601] Register r8 information: slab kmalloc-1k start 816d9800 pointer offset 0 size 1024
[    3.942244] Register r9 information: slab kmalloc-2k start 81c73800 pointer offset 148 size 2048
[    3.951058] Register r10 information: slab kmalloc-2k start 81c73800 pointer offset 64 size 2048
[    3.959873] Register r11 information: non-slab/vmalloc memory
[    3.965632] Register r12 information: non-paged memory
[    3.970781] Process kworker/u4:1 (pid: 64, stack limit = 0x(ptrval))
[    3.977148] Stack: (0x81c359d0 to 0x81c36000)
[    3.981517] 59c0:                                     80b2b668 80b2b5bc 000002e2 0000034e
[    3.989712] 59e0: 81c35a8c 816d98e8 81c35a14 7dbb550b 805bfcd0 810c35f0 81c73840 824addc0
[    3.997906] 5a00: 00001000 816d9800 81c73894 81c73840 81c35a34 81c35a20 805eb138 805eadd8
[    4.006099] 5a20: 810c35f0 00000045 81c35adc 81c35a38 80594188 805eb118 80d7c788 80dd1848
[    4.014292] 5a40: 00000000 81c35a50 80dca950 811194d3 80dca7c4 80dca944 80dca91c 816d9800
[    4.022485] 5a60: 81c34000 81c760a8 816d9800 80c58c98 810c35f0 816d98e8 00001000 00001000
[    4.030678] 5a80: 00000000 00000000 8017712c 81c60000 00000002 00000001 00000000 00000000
[    4.038870] 5aa0: 816d9900 816d9900 00000000 7dbb550b 805c700c 00000008 826282c8 826282c8
[    4.047062] 5ac0: 00001000 81e1ce40 00001000 00000002 81c35bf4 81c35ae0 805d9694 80593fc0
[    4.055255] 5ae0: 8017a970 80179ad8 00000179 00000000 81c35bcc 81c35b00 80177108 8017a950
[    4.063447] 5b00: 00000000 81c35b10 81c34000 00000000 81004fd8 81010a38 00000000 00000059
[    4.071639] 5b20: 816d98d4 81fbb718 00000013 826282c8 8017a940 81c35b40 81134448 00000400
[    4.079831] 5b40: 00000178 00000000 e063b9c1 00000000 c2000049 00000040 00000000 00000008
[    4.088024] 5b60: 82628300 82628380 00000000 00000000 81c34000 00000000 81fbb700 82628340
[    4.096216] 5b80: 826283c0 00001000 00000000 00000010 816d9800 826282c0 801766f8 00000000
[    4.104408] 5ba0: 00000000 81004fd8 00000049 00000000 00000000 00000001 80dcf940 80178de4
[    4.112601] 5bc0: 81c35c0c 7dbb550b 80178de4 81fbb700 00000010 00000010 810c35f4 81e1ce40
[    4.120793] 5be0: 81c40908 0000000c 81c35c64 81c35bf8 805a7f18 805d94a0 81c35c3c 816d9800
[    4.128985] 5c00: 00000010 81c34000 81c35c2c 81c35c18 8012fce0 805be90c 81c35c3c 81c35c28
[    4.137178] 5c20: 805be90c 80173210 81fbb600 81fbb6b4 81c35c5c 7dbb550b 81c35c64 81fbb700
[    4.145370] 5c40: 816d9800 00000010 810c35f4 81e1ce40 81c40908 0000000c 81c35c84 81c35c68
[    4.153565] 5c60: 805a8c78 805a7ed0 816d9800 81fbb700 00000010 00000000 81c35cac 81c35c88
[    4.161758] 5c80: 805a8dc4 805a8b68 816d9800 00000000 816d9800 00000000 8179f810 810c42d0
[    4.169950] 5ca0: 81c35ccc 81c35cb0 805e47b0 805a8d18 824aa240 81e1ea80 81c40908 81126b60
[    4.178144] 5cc0: 81c35d14 81c35cd0 8060db1c 805e46cc 81c35d14 81c35ce0 80dd90f8 810c4d58
[    4.186338] 5ce0: 80dd90dc 81fe9740 fffffffe 81fe9740 81e1ea80 00000000 810c4d6c 80c4b95c
[    4.194531] 5d00: 80dd9a3c 815c6810 81c35d34 81c35d18 8060dc9c 8060d8fc 8246b440 815c6800
[    4.202724] 5d20: 815c6810 eefd8e00 81c35d44 81c35d38 8060dd80 8060dbec 81c35d6c 81c35d48
[    4.210918] 5d40: 805e98a4 8060dd70 00000000 815c6810 810c45b0 81126e90 81126e90 80dd9a3c
[    4.219112] 5d60: 81c35d8c 81c35d70 80619574 805e9808 815c6810 00000000 810c45b0 81126e90
[    4.227305] 5d80: 81c35db4 81c35d90 806168dc 80619514 80625df0 80623c80 815c6810 810c45b0
[    4.235498] 5da0: 81c35e6c 815c6810 81c35dec 81c35db8 80616d04 80616800 81c35de4 81c35dc8
[    4.243691] 5dc0: 808382b0 80b2f444 8116e310 8116e314 81c35e6c 815c6810 00000003 80dd9a3c
[    4.251884] 5de0: 81c35e14 81c35df0 80616ec8 80616c60 00000001 810c45b0 81c35e6c 815c6810
[    4.260076] 5e00: 00000001 80dd9a3c 81c35e34 81c35e18 80617338 80616e90 00000000 81c35e6c
[    4.268269] 5e20: 80617284 81c34000 81c35e64 81c35e38 80614730 80617290 81c35e64 8171a06c
[    4.276461] 5e40: 81e220b8 7dbb550b 815c6810 81c34000 815c6854 81126e90 81c35e9c 81c35e68
[    4.284654] 5e60: 8061673c 806146a8 8060f5e0 815c6810 00000001 7dbb550b 00000000 810c5080
[    4.292847] 5e80: 810c5320 815c6810 81126e90 00000000 81c35eac 81c35ea0 80617554 80616650
[    4.301040] 5ea0: 81c35ecc 81c35eb0 80615694 80617544 810c5080 810c5080 810c5094 81126e90
[    4.309233] 5ec0: 81c35efc 81c35ed0 80615c6c 8061560c 80615bc0 810c50c0 817eeb00 81412800
[    4.317425] 5ee0: 814c3000 00000000 814c300d 81119a60 81c35f3c 81c35f00 80141488 80615bcc
[    4.325618] 5f00: 81c60000 81c34000 81c35f24 81c35f18 80143078 817eeb00 81412800 817eeb18
[    4.333811] 5f20: 81412818 81003d00 00000088 81412800 81c35f74 81c35f40 80141a48 80141298
[    4.342005] 5f40: 81c35f74 81c34000 801481ac 817efa40 817efc00 801417d8 817eeb00 00000000
[    4.350199] 5f60: 815a7e7c 81c34000 81c35fac 81c35f78 80149b1c 801417e4 817efc20 817efc20
[    4.358391] 5f80: ffffe000 817efa40 801499a8 00000000 00000000 00000000 00000000 00000000
[    4.366583] 5fa0: 00000000 81c35fb0 80100130 801499b4 00000000 00000000 00000000 00000000
[    4.374774] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.382966] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[    4.391155] Backtrace:
[    4.393613] [<805eadcc>] (stdp2690_get_edid) from [<805eb138>] (ge_b850v3_lvds_get_modes+0x2c/0x5c)
[    4.402691]  r10:81c73840 r9:81c73894 r8:816d9800 r7:00001000 r6:824addc0 r5:81c73840
[    4.410534]  r4:810c35f0
[    4.413073] [<805eb10c>] (ge_b850v3_lvds_get_modes) from [<80594188>] (drm_helper_probe_single_connector_modes+0x1d4/0x84c)
[    4.424240]  r5:00000045 r4:810c35f0
[    4.427822] [<80593fb4>] (drm_helper_probe_single_connector_modes) from [<805d9694>] (drm_client_modeset_probe+0x200/0x1384)
[    4.439074]  r10:00000002 r9:00001000 r8:81e1ce40 r7:00001000 r6:826282c8 r5:826282c8
[    4.446917]  r4:00000008
[    4.449455] [<805d9494>] (drm_client_modeset_probe) from [<805a7f18>] (__drm_fb_helper_initial_config_and_unlock+0x54/0x5b4)
[    4.460713]  r10:0000000c r9:81c40908 r8:81e1ce40 r7:810c35f4 r6:00000010 r5:00000010
[    4.468556]  r4:81fbb700
[    4.471095] [<805a7ec4>] (__drm_fb_helper_initial_config_and_unlock) from [<805a8c78>] (drm_fbdev_client_hotplug+0x11c/0x1b0)
[    4.482434]  r10:0000000c r9:81c40908 r8:81e1ce40 r7:810c35f4 r6:00000010 r5:816d9800
[    4.490276]  r4:81fbb700
[    4.492814] [<805a8b5c>] (drm_fbdev_client_hotplug) from [<805a8dc4>] (drm_fbdev_generic_setup+0xb8/0x1a4)
[    4.502494]  r7:00000000 r6:00000010 r5:81fbb700 r4:816d9800
[    4.508160] [<805a8d0c>] (drm_fbdev_generic_setup) from [<805e47b0>] (imx_drm_bind+0xf0/0x130)
[    4.516805]  r7:810c42d0 r6:8179f810 r5:00000000 r4:816d9800
[    4.522474] [<805e46c0>] (imx_drm_bind) from [<8060db1c>] (try_to_bring_up_master+0x22c/0x2f0)
[    4.531116]  r7:81126b60 r6:81c40908 r5:81e1ea80 r4:824aa240
[    4.536783] [<8060d8f0>] (try_to_bring_up_master) from [<8060dc9c>] (__component_add+0xbc/0x184)
[    4.545597]  r10:815c6810 r9:80dd9a3c r8:80c4b95c r7:810c4d6c r6:00000000 r5:81e1ea80
[    4.553440]  r4:81fe9740
[    4.555980] [<8060dbe0>] (__component_add) from [<8060dd80>] (component_add+0x1c/0x20)
[    4.563921]  r7:eefd8e00 r6:815c6810 r5:815c6800 r4:8246b440
[    4.569589] [<8060dd64>] (component_add) from [<805e98a4>] (dw_hdmi_imx_probe+0xa8/0xe8)
[    4.577702] [<805e97fc>] (dw_hdmi_imx_probe) from [<80619574>] (platform_probe+0x6c/0xc8)
[    4.585908]  r9:80dd9a3c r8:81126e90 r7:81126e90 r6:810c45b0 r5:815c6810 r4:00000000
[    4.593662] [<80619508>] (platform_probe) from [<806168dc>] (really_probe+0xe8/0x460)
[    4.601524]  r7:81126e90 r6:810c45b0 r5:00000000 r4:815c6810
[    4.607191] [<806167f4>] (really_probe) from [<80616d04>] (__driver_probe_device+0xb0/0x230)
[    4.615658]  r7:815c6810 r6:81c35e6c r5:810c45b0 r4:815c6810
[    4.621326] [<80616c54>] (__driver_probe_device) from [<80616ec8>] (driver_probe_device+0x44/0xe0)
[    4.630313]  r9:80dd9a3c r8:00000003 r7:815c6810 r6:81c35e6c r5:8116e314 r4:8116e310
[    4.638068] [<80616e84>] (driver_probe_device) from [<80617338>] (__device_attach_driver+0xb4/0x12c)
[    4.647227]  r9:80dd9a3c r8:00000001 r7:815c6810 r6:81c35e6c r5:810c45b0 r4:00000001
[    4.654981] [<80617284>] (__device_attach_driver) from [<80614730>] (bus_for_each_drv+0x94/0xd8)
[    4.663794]  r7:81c34000 r6:80617284 r5:81c35e6c r4:00000000
[    4.669461] [<8061469c>] (bus_for_each_drv) from [<8061673c>] (__device_attach+0xf8/0x190)
[    4.677753]  r7:81126e90 r6:815c6854 r5:81c34000 r4:815c6810
[    4.683419] [<80616644>] (__device_attach) from [<80617554>] (device_initial_probe+0x1c/0x20)
[    4.691971]  r8:00000000 r7:81126e90 r6:815c6810 r5:810c5320 r4:810c5080
[    4.698681] [<80617538>] (device_initial_probe) from [<80615694>] (bus_probe_device+0x94/0x9c)
[    4.707318] [<80615600>] (bus_probe_device) from [<80615c6c>] (deferred_probe_work_func+0xac/0xf0)
[    4.716305]  r7:81126e90 r6:810c5094 r5:810c5080 r4:810c5080
[    4.721973] [<80615bc0>] (deferred_probe_work_func) from [<80141488>] (process_one_work+0x1fc/0x54c)
[    4.731139]  r10:81119a60 r9:814c300d r8:00000000 r7:814c3000 r6:81412800 r5:817eeb00
[    4.738981]  r4:810c50c0 r3:80615bc0
[    4.742563] [<8014128c>] (process_one_work) from [<80141a48>] (worker_thread+0x270/0x570)
[    4.750765]  r10:81412800 r9:00000088 r8:81003d00 r7:81412818 r6:817eeb18 r5:81412800
[    4.758608]  r4:817eeb00
[    4.761147] [<801417d8>] (worker_thread) from [<80149b1c>] (kthread+0x174/0x190)
[    4.768574]  r10:81c34000 r9:815a7e7c r8:00000000 r7:817eeb00 r6:801417d8 r5:817efc00
[    4.776417]  r4:817efa40
[    4.778955] [<801499a8>] (kthread) from [<80100130>] (ret_from_fork+0x14/0x24)
[    4.786201] Exception stack(0x81c35fb0 to 0x81c35ff8)
[    4.791266] 5fa0:                                     00000000 00000000 00000000 00000000
[    4.799459] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.807651] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    4.814279]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:801499a8
[    4.822120]  r4:817efa40
[    4.824664] Code: e3a02080 e593001c e3a01d33 e3a05000 (e5979018)

Split the registration from the STDP4028 probe routine and only perform
registration once both the STDP4028 and STDP2690 have probed.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
CC: Peter Senna Tschudin <peter.senna@gmail.com>
CC: Martyn Welch <martyn.welch@collabora.co.uk>
CC: Neil Armstrong <narmstrong@baylibre.com>
CC: Robert Foss <robert.foss@linaro.org>
CC: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
CC: Jonas Karlman <jonas@kwiboo.se>
CC: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/43552c3404e8fdf92d8bc5658fac24e9f03c2c57.1637836606.git.martyn.welch@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: pci: Add shutdown method in PCI driver

[ Upstream commit c1020d3cf4752f61a6a413f632ea2ce2370e150d ]

On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.

Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].

[1]
BUG: Bad page state in process devlink pfn:22f73d
page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x2ffff00000000000()
raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
Modules linked in:
CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44
Hardware name: Marvell Armada 7040 TX4810M (DT)
Call trace:
 dump_backtrace+0x0/0x1d0
 show_stack+0x1c/0x28
 dump_stack+0xbc/0x118
 bad_page+0xcc/0xf8
 check_free_page_bad+0x80/0x88
 __free_pages_ok+0x3f8/0x418
 __free_pages+0x38/0x60
 kmem_freepages+0x200/0x2a8
 slab_destroy+0x28/0x68
 slabs_destroy+0x60/0x90
 ___cache_free+0x1b4/0x358
 kfree+0xc0/0x1d0
 skb_free_head+0x2c/0x38
 skb_release_data+0x110/0x1a0
 skb_release_all+0x2c/0x38
 consume_skb+0x38/0x130
 __dev_kfree_skb_any+0x44/0x50
 mlxsw_pci_rdq_fini+0x8c/0xb0
 mlxsw_pci_queue_fini.isra.0+0x28/0x58
 mlxsw_pci_queue_group_fini+0x58/0x88
 mlxsw_pci_aqs_fini+0x2c/0x60
 mlxsw_pci_fini+0x34/0x50
 mlxsw_core_bus_device_unregister+0x104/0x1d0
 mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48
 devlink_reload+0x44/0x158
 devlink_nl_cmd_reload+0x270/0x290
 genl_rcv_msg+0x188/0x2f0
 netlink_rcv_skb+0x5c/0x118
 genl_rcv+0x3c/0x50
 netlink_unicast+0x1bc/0x278
 netlink_sendmsg+0x194/0x390
 __sys_sendto+0xe0/0x158
 __arm64_sys_sendto+0x2c/0x38
 el0_svc_common.constprop.0+0x70/0x168
 do_el0_svc+0x28/0x88
 el0_sync_handler+0x88/0x190
 el0_sync+0x140/0x180

[2]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html

[3]
https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693

Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: b2c2: Add missing check in flexcop_pci_isr:

[ Upstream commit b13203032e679674c7c518f52a7ec0801ca3a829 ]

A out-of-bounds bug can be triggered by an interrupt, the reason for
this bug is the lack of checking of register values.

In flexcop_pci_isr, the driver reads value from a register and uses it as
a dma address. Finally, this address will be passed to the count parameter
of find_next_packet. If this value is larger than the size of dma, the
index of buffer will be out-of-bounds.

Fix this by adding a check after reading the value of the register.

The following KASAN report reveals it:

BUG: KASAN: slab-out-of-bounds in find_next_packet
drivers/media/dvb-core/dvb_demux.c:528 [inline]
BUG: KASAN: slab-out-of-bounds in _dvb_dmx_swfilter
drivers/media/dvb-core/dvb_demux.c:572 [inline]
BUG: KASAN: slab-out-of-bounds in dvb_dmx_swfilter+0x3fa/0x420
drivers/media/dvb-core/dvb_demux.c:603
Read of size 1 at addr ffff8880608c00a0 by task swapper/2/0

CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xec/0x156 lib/dump_stack.c:118
 print_address_description+0x78/0x290 mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report+0x25b/0x380 mm/kasan/report.c:412
 __asan_report_load1_noabort+0x19/0x20 mm/kasan/report.c:430
 find_next_packet drivers/media/dvb-core/dvb_demux.c:528 [inline]
 _dvb_dmx_swfilter drivers/media/dvb-core/dvb_demux.c:572 [inline]
 dvb_dmx_swfilter+0x3fa/0x420 drivers/media/dvb-core/dvb_demux.c:603
 flexcop_pass_dmx_data+0x2e/0x40 drivers/media/common/b2c2/flexcop.c:167
 flexcop_pci_isr+0x3d1/0x5d0 drivers/media/pci/b2c2/flexcop-pci.c:212
 __handle_irq_event_percpu+0xfb/0x770 kernel/irq/handle.c:149
 handle_irq_event_percpu+0x79/0x150 kernel/irq/handle.c:189
 handle_irq_event+0xac/0x140 kernel/irq/handle.c:206
 handle_fasteoi_irq+0x232/0x5c0 kernel/irq/chip.c:725
 generic_handle_irq_desc include/linux/irqdesc.h:155 [inline]
 handle_irq+0x230/0x3a0 arch/x86/kernel/irq_64.c:87
 do_IRQ+0xa7/0x1e0 arch/x86/kernel/irq.c:247
 common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670
 </IRQ>
RIP: 0010:native_safe_halt+0x28/0x30 arch/x86/include/asm/irqflags.h:61
Code: 00 00 55 be 04 00 00 00 48 c7 c7 00 62 2f 8c 48 89 e5 e8 fb 31
e8 f8 8b 05 75 4f 8e 03 85 c0 7e 07 0f 00 2d 8a 61 66 00 fb f4 <5d> c3
90 90 90 90 90 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41
RSP: 0018:ffff88806b71fcc8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde
RAX: 0000000000000000 RBX: ffffffff8bde44c8 RCX: ffffffff88a11285
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff8c2f6200
RBP: ffff88806b71fcc8 R08: fffffbfff185ec40 R09: fffffbfff185ec40
R10: 0000000000000001 R11: fffffbfff185ec40 R12: 0000000000000002
R13: ffffffff8be9d6e0 R14: 0000000000000000 R15: 0000000000000000
 arch_safe_halt arch/x86/include/asm/paravirt.h:94 [inline]
 default_idle+0x6f/0x360 arch/x86/kernel/process.c:557
 arch_cpu_idle+0xf/0x20 arch/x86/kernel/process.c:548
 default_idle_call+0x3b/0x60 kernel/sched/idle.c:93
 cpuidle_idle_call kernel/sched/idle.c:153 [inline]
 do_idle+0x2ab/0x3c0 kernel/sched/idle.c:263
 cpu_startup_entry+0xcb/0xe0 kernel/sched/idle.c:369
 start_secondary+0x3b8/0x4e0 arch/x86/kernel/smpboot.c:271
 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243

Allocated by task 1:
 save_stack+0x43/0xd0 mm/kasan/kasan.c:448
 set_track mm/kasan/kasan.c:460 [inline]
 kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:553
 kasan_slab_alloc+0x11/0x20 mm/kasan/kasan.c:490
 slab_post_alloc_hook mm/slab.h:445 [inline]
 slab_alloc_node mm/slub.c:2741 [inline]
 slab_alloc mm/slub.c:2749 [inline]
 kmem_cache_alloc+0xeb/0x280 mm/slub.c:2754
 kmem_cache_zalloc include/linux/slab.h:699 [inline]
 __kernfs_new_node+0xe2/0x6f0 fs/kernfs/dir.c:633
 kernfs_new_node+0x9a/0x120 fs/kernfs/dir.c:693
 __kernfs_create_file+0x5f/0x340 fs/kernfs/file.c:992
 sysfs_add_file_mode_ns+0x22a/0x4e0 fs/sysfs/file.c:306
 create_files fs/sysfs/group.c:63 [inline]
 internal_create_group+0x34e/0xc30 fs/sysfs/group.c:147
 sysfs_create_group fs/sysfs/group.c:173 [inline]
 sysfs_create_groups+0x9c/0x140 fs/sysfs/group.c:200
 driver_add_groups+0x3e/0x50 drivers/base/driver.c:129
 bus_add_driver+0x3a5/0x790 drivers/base/bus.c:684
 driver_register+0x1cd/0x410 drivers/base/driver.c:170
 __pci_register_driver+0x197/0x200 drivers/pci/pci-driver.c:1411
 cx88_audio_pci_driver_init+0x23/0x25 drivers/media/pci/cx88/cx88-alsa.c:
 1017
 do_one_initcall+0xe0/0x610 init/main.c:884
 do_initcall_level init/main.c:952 [inline]
 do_initcalls init/main.c:960 [inline]
 do_basic_setup init/main.c:978 [inline]
 kernel_init_freeable+0x4d0/0x592 init/main.c:1145
 kernel_init+0x18/0x190 init/main.c:1062
 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415

Freed by task 0:
(stack is not available)

The buggy address belongs to the object at ffff8880608c0000
 which belongs to the cache kernfs_node_cache of size 160
The buggy address is located 0 bytes to the right of
 160-byte region [ffff8880608c0000, ffff8880608c00a0)
The buggy address belongs to the page:
page:ffffea0001823000 count:1 mapcount:0 mapping:ffff88806bed1e00
index:0x0 compound_mapcount: 0
flags: 0x100000000008100(slab|head)
raw: 0100000000008100 dead000000000100 dead000000000200 ffff88806bed1e00
raw: 0000000000000000 0000000000240024 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8880608bff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 ffff8880608c0000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8880608c0080: 00 00 00 00 fc fc fc fc fc fc fc fc 00 00 00 00
                               ^
 ffff8880608c0100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 ffff8880608c0180: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================

Link: https://lore.kernel.org/linux-media/1620723603-30912-1-git-send-email-zheyuma97@gmail.com
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: apple: Do not reset quirks when the Fn key is not found

[ Upstream commit a5fe7864d8ada170f19cc47d176bf8260ffb4263 ]

When a keyboard without a function key is detected, instead of removing
all quirks, remove only the APPLE_HAS_FN quirk.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: f_fs: Use stream_open() for endpoint files

[ Upstream commit c76ef96fc00eb398c8fc836b0eb2f82bcc619dc7 ]

Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.

The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655e3
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.

It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.

Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1636712682-1226-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/nouveau/pmu/gm200-: avoid touching PMU outside of DEVINIT/PREOS/ACR

[ Upstream commit 1d2271d2fb85e54bfc9630a6c30ac0feb9ffb983 ]

There have been reports of the WFI timing out on some boards, and a
patch was proposed to just remove it.  This stuff is rather fragile,
and I believe the WFI might be needed with our FW prior to GM200.

However, we probably should not be touching PMU during init on GPUs
where we depend on NVIDIA FW, outside of limited circumstances, so
this should be a somewhat safer change that achieves the desired
result.

Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/10
Signed-off-by: Sasha Levin <sashal@kernel.org>

ar5523: Fix null-ptr-deref with unexpected WDCMSG_TARGET_START reply

[ Upstream commit ae80b6033834342601e99f74f6a62ff5092b1cee ]

Unexpected WDCMSG_TARGET_START replay can lead to null-ptr-deref
when ar->tx_cmd->odata is NULL. The patch adds a null check to
prevent such case.

KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
 ar5523_cmd+0x46a/0x581 [ar5523]
 ar5523_probe.cold+0x1b7/0x18da [ar5523]
 ? ar5523_cmd_rx_cb+0x7a0/0x7a0 [ar5523]
 ? __pm_runtime_set_status+0x54a/0x8f0
 ? _raw_spin_trylock_bh+0x120/0x120
 ? pm_runtime_barrier+0x220/0x220
 ? __pm_runtime_resume+0xb1/0xf0
 usb_probe_interface+0x25b/0x710
 really_probe+0x209/0x5d0
 driver_probe_device+0xc6/0x1b0
 device_driver_attach+0xe2/0x120

I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.

After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START,
I got the null-ptr-deref bug. I believe the bug is triggerable whenever
cmd->odata is NULL. After patching, I tested with the same input and no
longer see the KASAN report.

This was NOT tested on a real device.

Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXsmPQ3awHFLuAj2@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs: dlm: filter user dlm messages for kernel locks

[ Upstream commit 6c2e3bf68f3e5e5a647aa52be246d5f552d7496d ]

This patch fixes the following crash by receiving a invalid message:

[  160.672220] ==================================================================
[  160.676206] BUG: KASAN: user-memory-access in dlm_user_add_ast+0xc3/0x370
[  160.679659] Read of size 8 at addr 00000000deadbeef by task kworker/u32:13/319
[  160.681447]
[  160.681824] CPU: 10 PID: 319 Comm: kworker/u32:13 Not tainted 5.14.0-rc2+ #399
[  160.683472] Hardware name: Red Hat KVM/RHEL-AV, BIOS 1.14.0-1.module+el8.6.0+12648+6ede71a5 04/01/2014
[  160.685574] Workqueue: dlm_recv process_recv_sockets
[  160.686721] Call Trace:
[  160.687310]  dump_stack_lvl+0x56/0x6f
[  160.688169]  ? dlm_user_add_ast+0xc3/0x370
[  160.689116]  kasan_report.cold.14+0x116/0x11b
[  160.690138]  ? dlm_user_add_ast+0xc3/0x370
[  160.690832]  dlm_user_add_ast+0xc3/0x370
[  160.691502]  _receive_unlock_reply+0x103/0x170
[  160.692241]  _receive_message+0x11df/0x1ec0
[  160.692926]  ? rcu_read_lock_sched_held+0xa1/0xd0
[  160.693700]  ? rcu_read_lock_bh_held+0xb0/0xb0
[  160.694427]  ? lock_acquire+0x175/0x400
[  160.695058]  ? do_purge.isra.51+0x200/0x200
[  160.695744]  ? lock_acquired+0x360/0x5d0
[  160.696400]  ? lock_contended+0x6a0/0x6a0
[  160.697055]  ? lock_release+0x21d/0x5e0
[  160.697686]  ? lock_is_held_type+0xe0/0x110
[  160.698352]  ? lock_is_held_type+0xe0/0x110
[  160.699026]  ? ___might_sleep+0x1cc/0x1e0
[  160.699698]  ? dlm_wait_requestqueue+0x94/0x140
[  160.700451]  ? dlm_process_requestqueue+0x240/0x240
[  160.701249]  ? down_write_killable+0x2b0/0x2b0
[  160.701988]  ? do_raw_spin_unlock+0xa2/0x130
[  160.702690]  dlm_receive_buffer+0x1a5/0x210
[  160.703385]  dlm_process_incoming_buffer+0x726/0x9f0
[  160.704210]  receive_from_sock+0x1c0/0x3b0
[  160.704886]  ? dlm_tcp_shutdown+0x30/0x30
[  160.705561]  ? lock_acquire+0x175/0x400
[  160.706197]  ? rcu_read_lock_sched_held+0xa1/0xd0
[  160.706941]  ? rcu_read_lock_bh_held+0xb0/0xb0
[  160.707681]  process_recv_sockets+0x32/0x40
[  160.708366]  process_one_work+0x55e/0xad0
[  160.709045]  ? pwq_dec_nr_in_flight+0x110/0x110
[  160.709820]  worker_thread+0x65/0x5e0
[  160.710423]  ? process_one_work+0xad0/0xad0
[  160.711087]  kthread+0x1ed/0x220
[  160.711628]  ? set_kthread_struct+0x80/0x80
[  160.712314]  ret_from_fork+0x22/0x30

The issue is that we received a DLM message for a user lock but the
destination lock is a kernel lock. Note that the address which is trying
to derefence is 00000000deadbeef, which is in a kernel lock
lkb->lkb_astparam, this field should never be derefenced by the DLM
kernel stack. In case of a user lock lkb->lkb_astparam is lkb->lkb_ua
(memory is shared by a union field). The struct lkb_ua will be handled
by the DLM kernel stack but on a kernel lock it will contain invalid
data and ends in most likely crashing the kernel.

It can be reproduced with two cluster nodes.

node 2:
dlm_tool join test
echo "862 fooobaar 1 2 1" > /sys/kernel/debug/dlm/test_locks
echo "862 3 1" > /sys/kernel/debug/dlm/test_waiters

node 1:
dlm_tool join test

python:
foo = DLM(h_cmd=3, o_nextcmd=1, h_nodeid=1, h_lockspace=0x77222027, \
          m_type=7, m_flags=0x1, m_remid=0x862, m_result=0xFFFEFFFE)
newFile = open("/sys/kernel/debug/dlm/comms/2/rawmsg", "wb")
newFile.write(bytes(foo))

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Fix debugfs entry leak in hci_register_dev()

[ Upstream commit 5a4bb6a8e981d3d0d492aa38412ee80b21033177 ]

Fault injection test report debugfs entry leak as follows:

debugfs: Directory 'hci0' with parent 'bluetooth' already present!

When register_pm_notifier() failed in hci_register_dev(), the debugfs
create by debugfs_create_dir() do not removed in the error handing path.

Add the remove debugfs code to fix it.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/cxgb4: Set queue pair state when being queried

[ Upstream commit e375b9c92985e409c4bb95dd43d34915ea7f5e28 ]

The API for ib_query_qp requires the driver to set cur_qp_state on return,
add the missing set.

Fixes: 67bbc05512d8 ("RDMA/cxgb4: Add query_qp support")
Link: https://lore.kernel.org/r/20211220152530.60399-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mips: bcm63xx: add support for clk_set_parent()

[ Upstream commit 6f03055d508ff4feb8db02ba3df9303a1db8d381 ]

The MIPS BMC63XX subarch does not provide/support clk_set_parent().
This causes build errors in a few drivers, so add a simple implementation
of that function so that callers of it will build without errors.

Fixes these build errors:

ERROR: modpost: "clk_set_parent" [sound/soc/jz4740/snd-soc-jz4740-i2s.ko] undefined!
ERROR: modpost: "clk_set_parent" [sound/soc/atmel/snd-soc-atmel-i2s.ko] undefined!

Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs." )
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mips: lantiq: add support for clk_set_parent()

[ Upstream commit 76f66dfd60dc5d2f9dec22d99091fea1035c5d03 ]

Provide a simple implementation of clk_set_parent() in the lantiq
subarch so that callers of it will build without errors.

Fixes these build errors:

ERROR: modpost: "clk_set_parent" [sound/soc/jz4740/snd-soc-jz4740-i2s.ko] undefined!
ERROR: modpost: "clk_set_parent" [sound/soc/atmel/snd-soc-atmel-i2s.ko] undefined!

Fixes: 171bb2f19ed6 ("MIPS: Lantiq: Add initial support for Lantiq SoCs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
--to=linux-mips@vger.kernel.org --cc="John Crispin <john@phrozen.org>" --cc="Jonathan Cameron <jic23@kernel.org>" --cc="Russell King <linux@armlinux.org.uk>" --cc="Andy Shevchenko <andy.shevchenko@gmail.com>" --cc=alsa-devel@alsa-project.org --to="Thomas Bogendoerfer <tsbogend@alpha.franken.de>"
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: lattice-ecp3-config: Fix task hung when firmware load failed

[ Upstream commit fcee5ce50bdb21116711e38635e3865594af907e ]

When firmware load failed, kernel report task hung as follows:

INFO: task xrun:5191 blocked for more than 147 seconds.
      Tainted: G        W         5.16.0-rc5-next-20211220+ #11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:xrun            state:D stack:    0 pid: 5191 ppid:   270 flags:0x00000004
Call Trace:
 __schedule+0xc12/0x4b50 kernel/sched/core.c:4986
 schedule+0xd7/0x260 kernel/sched/core.c:6369 (discriminator 1)
 schedule_timeout+0x7aa/0xa80 kernel/time/timer.c:1857
 wait_for_completion+0x181/0x290 kernel/sched/completion.c:85
 lattice_ecp3_remove+0x32/0x40 drivers/misc/lattice-ecp3-config.c:221
 spi_remove+0x72/0xb0 drivers/spi/spi.c:409

lattice_ecp3_remove() wait for signals from firmware loading, but when
load failed, firmware_load() does not send this signal. This cause
device remove hung. Fix it by sending signal even if load failed.

Fixes: 781551df57c7 ("misc: Add Lattice ECP3 FPGA configuration via SPI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20211228125522.3122284-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: samsung: idma: Check of ioremap return value

[ Upstream commit 3ecb46755eb85456b459a1a9f952c52986bce8ec ]

Because of the potential failure of the ioremap(), the buf->area could
be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.

Fixes: f09aecd50f39 ("ASoC: SAMSUNG: Add I2S0 internal dma driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211228034026.1659385-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/iova: Fix race between FQ timeout and teardown

[ Upstream commit d7061627d701c90e1cac1e1e60c45292f64f3470 ]

It turns out to be possible for hotplugging out a device to reach the
stage of tearing down the device's group and default domain before the
domain's flush queue has drained naturally. At this point, it is then
possible for the timeout to expire just before the del_timer() call
in free_iova_flush_queue(), such that we then proceed to free the FQ
resources while fq_flush_timeout() is still accessing them on another
CPU. Crashes due to this have been observed in the wild while removing
NVMe devices.

Close the race window by using del_timer_sync() to safely wait for any
active timeout handler to finish before we start to free things. We
already avoid any locking in free_iova_flush_queue() since the FQ is
supposed to be inactive anyway, so the potential deadlock scenario does
not apply.

Fixes: 9a005a800ae8 ("iommu/iova: Add flush timer")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[ rm: rewrite commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0a365e5b07f14b7344677ad6a9a734966a8422ce.1639753638.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: pxa/mmp: stop referencing config->slave_id

[ Upstream commit 134c37fa250a87a7e77c80a7c59ae16c462e46e0 ]

The last driver referencing the slave_id on Marvell PXA and MMP platforms
was the SPI driver, but this stopped doing so a long time ago, so the
TODO from the earlier patch can no be removed.

Fixes: b729bf34535e ("spi/pxa2xx: Don't use slave_id of dma_slave_config")
Fixes: 13b3006b8ebd ("dma: mmp_pdma: add filter function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-7-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/core: Let ib_find_gid() continue search even after empty entry

[ Upstream commit 483d805191a23191f8294bbf9b4e94836f5d92e4 ]

Currently, ib_find_gid() will stop searching after encountering the first
empty GID table entry. This behavior is wrong since neither IB nor RoCE
spec enforce tightly packed GID tables.

For example, when a valid GID entry exists at index N, and if a GID entry
is empty at index N-1, ib_find_gid() will fail to find the valid entry.

Fix it by making ib_find_gid() continue searching even after encountering
missing entries.

Fixes: 5eb620c81ce3 ("IB/core: Add helpers for uncached GID and P_Key searches")
Link: https://lore.kernel.org/r/e55d331b96cecfc2cf19803d16e7109ea966882d.1639055490.git.leonro@nvidia.com
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ufs: Fix race conditions related to driver data

[ Upstream commit 21ad0e49085deb22c094f91f9da57319a97188e4 ]

The driver data pointer must be set before any callbacks are registered
that use that pointer. Hence move the initialization of that pointer from
after the ufshcd_init() call to inside ufshcd_init().

Link: https://lore.kernel.org/r/20211203231950.193369-7-bvanassche@acm.org
Fixes: 3b1d05807a9a ("[SCSI] ufs: Segregate PCI Specific Code")
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

char/mwave: Adjust io port register size

[ Upstream commit f5912cc19acd7c24b2dbf65a6340bf194244f085 ]

Using MKWORD() on a byte-sized variable results in OOB read. Expand the
size of the reserved area so both MKWORD and MKBYTE continue to work
without overflow. Silences this warning on a -Warray-bounds build:

drivers/char/mwave/3780i.h:346:22: error: array subscript 'short unsigned int[0]' is partly outside array bounds of 'DSP_ISA_SLAVE_CONTROL[1]' [-Werror=array-bounds]
  346 | #define MKWORD(var) (*((unsigned short *)(&var)))
      |                     ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/char/mwave/3780i.h:356:40: note: in definition of macro 'OutWordDsp'
  356 | #define OutWordDsp(index,value)   outw(value,usDspBaseIO+index)
      |                                        ^~~~~
drivers/char/mwave/3780i.c:373:41: note: in expansion of macro 'MKWORD'
  373 |         OutWordDsp(DSP_IsaSlaveControl, MKWORD(rSlaveControl));
      |                                         ^~~~~~
drivers/char/mwave/3780i.c:358:31: note: while referencing 'rSlaveControl'
  358 |         DSP_ISA_SLAVE_CONTROL rSlaveControl;
      |                               ^~~~~~~~~~~~~

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211203084206.3104326-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: oss: fix compile error when OSS_DEBUG is enabled

[ Upstream commit 8e7daf318d97f25e18b2fc7eb5909e34cd903575 ]

Fix compile error when OSS_DEBUG is enabled:
    sound/core/oss/pcm_oss.c: In function 'snd_pcm_oss_set_trigger':
    sound/core/oss/pcm_oss.c:2055:10: error: 'substream' undeclared (first
    use in this function); did you mean 'csubstream'?
      pcm_dbg(substream->pcm, "pcm_oss: trigger = 0x%x\n", trigger);
              ^

Fixes: 61efcee8608c ("ALSA: oss: Use standard printk helpers")
Signed-off-by: Bixuan Cui <cuibixuan@linux.alibaba.com>
Link: https://lore.kernel.org/r/1638349134-110369-1-git-send-email-cuibixuan@linux.alibaba.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/prom_init: Fix improper check of prom_getprop()

[ Upstream commit 869fb7e5aecbc163003f93f36dcc26d0554319f6 ]

prom_getprop() can return PROM_ERROR. Binary operator can not identify
it.

Fixes: 94d2dde738a5 ("[POWERPC] Efika: prune fixups and make them more carefull")
Signed-off-by: Peiwei Hu <jlu.hpw@foxmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/tencent_BA28CC6897B7C95A92EB8C580B5D18589105@qq.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hns: Validate the pkey index

[ Upstream commit 2a67fcfa0db6b4075515bd23497750849b88850f ]

Before query pkey, make sure that the queried index is valid.

Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver")
Link: https://lore.kernel.org/r/20211117145954.123893-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda: Add missing rwsem around snd_ctl_remove() calls

[ Upstream commit 80bd64af75b4bb11c0329bc66c35da2ddfb66d88 ]

snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation).  This patch add the missing
rwsem calls around it.

Fixes: d13bd412dce2 ("ALSA: hda - Manage kcontrol lists")
Link: https://lore.kernel.org/r/20211116071314.15065-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: PCM: Add missing rwsem around snd_ctl_remove() calls

[ Upstream commit 5471e9762e1af4b7df057a96bfd46cc250979b88 ]

snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation).  This patch add the missing
rwsem calls around it.

Fixes: a8ff48cb7083 ("ALSA: pcm: Free chmap at PCM free callback, too")
Link: https://lore.kernel.org/r/20211116071314.15065-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: jack: Add missing rwsem around snd_ctl_remove() calls

[ Upstream commit 06764dc931848c3a9bc01a63bbf76a605408bb54 ]

snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation).  This patch add the missing
rwsem calls around it.

Fixes: 9058cbe1eed2 ("ALSA: jack: implement kctl creating for jack devices")
Link: https://lore.kernel.org/r/20211116071314.15065-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: avoid trim error on fs with small groups

[ Upstream commit 173b6e383d2a204c9921ffc1eca3b87aa2106c33 ]

A user reported FITRIM ioctl failing for him on ext4 on some devices
without apparent reason.  After some debugging we've found out that
these devices (being LVM volumes) report rather large discard
granularity of 42MB and the filesystem had 1k blocksize and thus group
size of 8MB. Because ext4 FITRIM implementation puts discard
granularity into minlen, ext4_trim_fs() declared the trim request as
invalid. However just silently doing nothing seems to be a more
appropriate reaction to such combination of parameters since user did
not specify anything wrong.

CC: Lukas Czerner <lczerner@redhat.com>
Fixes: 5c2ed62fd447 ("ext4: Adjust minlen with discard_granularity in the FITRIM ioctl")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20211112152202.26614-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mcs7830: handle usb read errors properly

[ Upstream commit d668769eb9c52b150753f1653f7f5a0aeb8239d2 ]

Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().

usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.

So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs

Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d7083438 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pcmcia: fix setting of kthread task states

[ Upstream commit fbb3485f1f931102d8ba606f1c28123f5b48afa3 ]

We need to set TASK_INTERRUPTIBLE before calling kthread_should_stop().
Otherwise, kthread_stop() might see that the pccardd thread is still
in TASK_RUNNING state and fail to wake it up.

Additionally, we only need to set the state back to TASK_RUNNING if
kthread_should_stop() breaks the loop.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Fixes: d3046ba809ce ("pcmcia: fix a boot time warning in pcmcia cs code")
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: xilinx_can: xcan_probe(): check for error irq

[ Upstream commit c6564c13dae25cd7f8e1de5127b4da4500ee5844 ]

For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().

Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: softing: softing_startstop(): fix set but not used variable warning

[ Upstream commit 370d988cc529598ebaec6487d4f84c2115dc696b ]

In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.

To fix the warning:

| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]

remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.

Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a179 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tpm: add request_locality before write TPM_INT_ENABLE

[ Upstream commit 0ef333f5ba7f24f5d8478425c163d3097f1c7afd ]

Locality is not appropriately requested before writing the int mask.
Add the missing boilerplate.

Fixes: e6aef069b6e9 ("tpm_tis: convert to using locality callbacks")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: spi-meson-spifc: Add missing pm_runtime_disable() in meson_spifc_probe

[ Upstream commit 69c1b87516e327a60b39f96b778fe683259408bf ]

If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for meson_spifc_probe.

Fixes: c3e4bc5434d2 ("spi: meson: Add support for Amlogic Meson SPIFC")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220107075424.7774-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fsl/fman: Check for null pointer after calling devm_ioremap

[ Upstream commit d5a73ec96cc57cf67e51b12820fc2354e7ca46f8 ]

As the possible failure of the allocation, the devm_ioremap() may return
NULL pointer.
Take tgec_initialization() as an example.
If allocation fails, the params->base_addr will be NULL pointer and will
be assigned to tgec->regs in tgec_config().
Then it will cause the dereference of NULL pointer in set_mac_address(),
which is called by tgec_init().
Therefore, it should be better to add the sanity check after the calling
of the devm_ioremap().

Fixes: 3933961682a3 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ppp: ensure minimum packet size in ppp_write()

[ Upstream commit 44073187990d5629804ce0627525f6ea5cfef171 ]

It seems pretty clear ppp layer assumed user space
would always be kind to provide enough data
in their write() to a ppp device.

This patch makes sure user provides at least
2 bytes.

It adds PPP_PROTO_LEN macro that could replace
in net-next many occurrences of hard-coded 2 value.

I replaced only one occurrence to ease backports
to stable kernels.

The bug manifests in the following report:

BUG: KMSAN: uninit-value in ppp_send_frame+0x28d/0x27c0 drivers/net/ppp/ppp_generic.c:1740
 ppp_send_frame+0x28d/0x27c0 drivers/net/ppp/ppp_generic.c:1740
 __ppp_xmit_process+0x23e/0x4b0 drivers/net/ppp/ppp_generic.c:1640
 ppp_xmit_process+0x1fe/0x480 drivers/net/ppp/ppp_generic.c:1661
 ppp_write+0x5cb/0x5e0 drivers/net/ppp/ppp_generic.c:513
 do_iter_write+0xb0c/0x1500 fs/read_write.c:853
 vfs_writev fs/read_write.c:924 [inline]
 do_writev+0x645/0xe00 fs/read_write.c:967
 __do_sys_writev fs/read_write.c:1040 [inline]
 __se_sys_writev fs/read_write.c:1037 [inline]
 __x64_sys_writev+0xe5/0x120 fs/read_write.c:1037
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Uninit was created at:
 slab_post_alloc_hook mm/slab.h:524 [inline]
 slab_alloc_node mm/slub.c:3251 [inline]
 __kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
 kmalloc_reserve net/core/skbuff.c:354 [inline]
 __alloc_skb+0x545/0xf90 net/core/skbuff.c:426
 alloc_skb include/linux/skbuff.h:1126 [inline]
 ppp_write+0x11d/0x5e0 drivers/net/ppp/ppp_generic.c:501
 do_iter_write+0xb0c/0x1500 fs/read_write.c:853
 vfs_writev fs/read_write.c:924 [inline]
 do_writev+0x645/0xe00 fs/read_write.c:967
 __do_sys_writev fs/read_write.c:1040 [inline]
 __se_sys_writev fs/read_write.c:1037 [inline]
 __x64_sys_writev+0xe5/0x120 fs/read_write.c:1037
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pcmcia: rsrc_nonstatic: Fix a NULL pointer dereference in nonstatic_find_mem_region()

[ Upstream commit 977d2e7c63c3d04d07ba340b39987742e3241554 ]

In nonstatic_find_mem_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().

Fix this bug by adding a check of res.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pcmcia: rsrc_nonstatic: Fix a NULL pointer dereference in __nonstatic_find_io_region()

[ Upstream commit ca0fe0d7c35c97528bdf621fdca75f13157c27af ]

In __nonstatic_find_io_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There is a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().

Fix this bug by adding a check of res.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
[linux@dominikbrodowski.net: Fix typo in commit message]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/mce/inject: Avoid out-of-bounds write when setting flags

[ Upstream commit de768416b203ac84e02a757b782a32efb388476f ]

A contrived zero-length write, for example, by using write(2):

  ...
  ret = write(fd, str, 0);
  ...

to the "flags" file causes:

  BUG: KASAN: stack-out-of-bounds in flags_write
  Write of size 1 at addr ffff888019be7ddf by task writefile/3787

  CPU: 4 PID: 3787 Comm: writefile Not tainted 5.16.0-rc7+ #12
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014

due to accessing buf one char before its start.

Prevent such out-of-bounds access.

  [ bp: Productize into a proper patch. Link below is the next best
    thing because the original mail didn't get archived on lore. ]

Fixes: 0451d14d0561 ("EDAC, mce_amd_inj: Modify flags attribute to use string arguments")
Signed-off-by: Zhang Zixun <zhang133010@icloud.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/linux-edac/YcnePfF1OOqoQwrX@zn.tnic/
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: ftdi-elan: fix memory leak on device disconnect

[ Upstream commit 1646566b5e0c556f779180a8514e521ac735de1e ]

'ftdi' is alloced when probe device, but not free on device disconnect,
this cause a memory leak as follows:

unreferenced object 0xffff88800d584000 (size 8400):
  comm "kworker/0:2", pid 3809, jiffies 4295453055 (age 13.784s)
  hex dump (first 32 bytes):
    00 40 58 0d 80 88 ff ff 00 40 58 0d 80 88 ff ff  .@X......@X.....
    00 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de  .............N..
  backtrace:
    [<000000000d47f947>] kmalloc_order_trace+0x19/0x110 mm/slab_common.c:960
    [<000000008548ac68>] ftdi_elan_probe+0x8c/0x880 drivers/usb/misc/ftdi-elan.c:2647
    [<000000007f73e422>] usb_probe_interface+0x31b/0x800 drivers/usb/core/driver.c:396
    [<00000000fe8d07fc>] really_probe+0x299/0xc30 drivers/base/dd.c:517
    [<0000000005da7d32>] __driver_probe_device+0x357/0x500 drivers/base/dd.c:751
    [<000000003c2c9579>] driver_probe_device+0x4e/0x140 drivers/base/dd.c:781

Fix it by freeing 'ftdi' after nobody use it.

Fixes: a5c66e4b2418 ("USB: ftdi-elan: client driver for ELAN Uxxx adapters")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20211217083428.2441-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: msi001: fix possible null-ptr-deref in msi001_probe()

[ Upstream commit 3d5831a40d3464eea158180eb12cbd81c5edfb6a ]

I got a null-ptr-deref report:

BUG: kernel NULL pointer dereference, address: 0000000000000060
...
RIP: 0010:v4l2_ctrl_auto_cluster+0x57/0x270
...
Call Trace:
 msi001_probe+0x13b/0x24b [msi001]
 spi_probe+0xeb/0x130
...
 do_syscall_64+0x35/0xb0

In msi001_probe(), if the creation of control for bandwidth_auto
fails, there will be a null-ptr-deref issue when it is used in
v4l2_ctrl_auto_cluster().

Check dev->hdl.error before v4l2_ctrl_auto_cluster() to fix this bug.

Link: https://lore.kernel.org/linux-media/20211026112348.2878040-1-wanghai38@huawei.com
Fixes: 93203dd6c7c4 ("[media] msi001: Mirics MSi001 silicon tuner driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: dw2102: Fix use after free

[ Upstream commit 589a9f0eb799f77de2c09583bf5bad221fa5d685 ]

dvb_usb_device_init stores parts of properties at d->props
and d->desc and uses it on dvb_usb_device_exit.
Free of properties on module probe leads to use after free.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204597

The patch makes properties static instead of allocated on heap to prevent
memleak and use after free.
Also fixes s421_properties.devices initialization to have 2 element
instead of 6 copied from p7500_properties.

[mchehab: fix function call alignments]
Link: https://lore.kernel.org/linux-media/20190822104147.4420-1-vasilyev@ispras.ru
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Fixes: 299c7007e936 ("media: dw2102: Fix memleak on sequence of probes")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/rt: Try to restart rt period timer when rt runtime exceeded

[ Upstream commit 9b58e976b3b391c0cf02e038d53dd0478ed3013c ]

When rt_runtime is modified from -1 to a valid control value, it may
cause the task to be throttled all the time. Operations like the following
will trigger the bug. E.g:

  1. echo -1 > /proc/sys/kernel/sched_rt_runtime_us
  2. Run a FIFO task named A that executes while(1)
  3. echo 950000 > /proc/sys/kernel/sched_rt_runtime_us

When rt_runtime is -1, The rt period timer will not be activated when task
A enqueued. And then the task will be throttled after setting rt_runtime to
950,000. The task will always be throttled because the rt period timer is
not activated.

Fixes: d0b27fa77854 ("sched: rt-group: synchonised bandwidth period")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Hua <hucool.lihua@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211203033618.11895-1-hucool.lihua@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: si2157: Fix "warm" tuner state detection

[ Upstream commit a6441ea29cb2c9314654e093a1cd8020b9b851c8 ]

Commit e955f959ac52 ("media: si2157: Better check for running tuner in
init") completely broke the "warm" tuner detection of the si2157 driver
due to a simple endian error: The Si2157 CRYSTAL_TRIM property code is
0x0402 and needs to be transmitted LSB first. However, it was inserted
MSB first, causing the warm detection to always fail and spam the kernel
log with tuner initialization messages each time the DVB frontend
device was closed and reopened:

[  312.215682] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[  312.264334] si2157 16-0060: firmware version: 3.0.5
[  342.248593] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[  342.295743] si2157 16-0060: firmware version: 3.0.5
[  372.328574] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[  372.385035] si2157 16-0060: firmware version: 3.0.5

Also, the reinitializations were observed disturb _other_ tuners on
multi-tuner cards such as the Hauppauge WinTV-QuadHD, leading to missed
or errored packets when one of the other DVB frontend devices on that
card was opened.

Fix the order of the property code bytes to make the warm detection work
again, also reducing the tuner initialization message in the kernel log
to once per power-on, as well as fixing the interference with other
tuners.

Link: https://lore.kernel.org/linux-media/trinity-2a86eb9d-6264-4387-95e1-ba7b79a4050f-1638392923493@3c-app-gmx-bap03
Fixes: e955f959ac52 ("media: si2157: Better check for running tuner in init")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: saa7146: mxb: Fix a NULL pointer dereference in mxb_attach()

[ Upstream commit 0407c49ebe330333478440157c640fffd986f41b ]

In mxb_attach(dev, info), saa7146_vv_init() is called to allocate a
new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of mxb_probe(dev). There is a dereference of dev->vv_data
in saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init().

Fix this bug by adding a check of saa7146_vv_init().

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_VIDEO_MXB=m show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: 03b1930efd3c ("V4L/DVB: saa7146: fix regression of the av7110/budget-av driver")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: dib8000: Fix a memleak in dib8000_init()

[ Upstream commit 8dbdcc7269a83305ee9d677b75064d3530a48ee2 ]

In dib8000_init(), the variable fe is not freed or passed out on the
failure of dib8000_identify(&state->i2c), which could lead to a memleak.

Fix this bug by adding a kfree of fe in the error path.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_DVB_DIB8000=m show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: 77e2c0f5d471 ("V4L/DVB (12900): DiB8000: added support for DiBcom ISDB-T/ISDB-Tsb demodulator DiB8000")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

floppy: Fix hang in watchdog when disk is ejected

[ Upstream commit fb48febce7e30baed94dd791e19521abd2c3fd83 ]

When the watchdog detects a disk change, it calls cancel_activity(),
which in turn tries to cancel the fd_timer delayed work.

In the above scenario, fd_timer_fn is set to fd_watchdog(), meaning
it is trying to cancel its own work.
This results in a hang as cancel_delayed_work_sync() is waiting for the
watchdog (itself) to return, which never happens.

This can be reproduced relatively consistently by attempting to read a
broken floppy, and ejecting it while IO is being attempted and retried.

To resolve this, this patch calls cancel_delayed_work() instead, which
cancels the work without waiting for the watchdog to return and finish.

Before this regression was introduced, the code in this section used
del_timer(), and not del_timer_sync() to delete the watchdog timer.

Link: https://lore.kernel.org/r/399e486c-6540-db27-76aa-7a271b061f76@tasossah.com
Fixes: 070ad7e793dc ("floppy: convert to delayed work and single-thread wq")
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: amba-pl011: do not request memory region twice

[ Upstream commit d1180405c7b5c7a1c6bde79d5fc24fe931430737 ]

With commit 3873e2d7f63a ("drivers: PL011: refactor pl011_probe()") the
function devm_ioremap() called from pl011_setup_port() was replaced with
devm_ioremap_resource(). Since this function not only remaps but also
requests the ports io memory region it now collides with the .config_port()
callback which requests the same region at uart port registration.

Since devm_ioremap_resource() already claims the memory successfully, the
request in .config_port() fails.

Later at uart port deregistration the attempt to release the unclaimed
memory also fails. The failure results in a “Trying to free nonexistent
resource" warning.

Fix these issues by removing the callbacks that implement the redundant
memory allocation/release. Also make sure that changing the drivers io
memory base address via TIOCSSERIAL is not allowed any more.

Fixes: 3873e2d7f63a ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20211129174238.8333-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/radeon/radeon_kms: Fix a NULL pointer dereference in radeon_driver_open_kms()

[ Upstream commit ab50cb9df8896b39aae65c537a30de2c79c19735 ]

In radeon_driver_open_kms(), radeon_vm_bo_add() is assigned to
vm->ib_bo_va and passes and used in radeon_vm_bo_set_addr(). In
radeon_vm_bo_set_addr(), there is a dereference of vm->ib_bo_va,
which could lead to a NULL pointer dereference on failure of
radeon_vm_bo_add().

Fix this bug by adding a check of vm->ib_bo_va.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_DRM_RADEON=m show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: cc9e67e3d700 ("drm/radeon: fix VM IB handling")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Fix a NULL pointer dereference in amdgpu_connector_lcd_native_mode()

[ Upstream commit b220110e4cd442156f36e1d9b4914bb9e87b0d00 ]

In amdgpu_connector_lcd_native_mode(), the return value of
drm_mode_duplicate() is assigned to mode, and there is a dereference
of it in amdgpu_connector_lcd_native_mode(), which will lead to a NULL
pointer dereference on failure of drm_mode_duplicate().

Fix this bug add a check of mode.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_DRM_AMDGPU=m show no new warnings, and
our static analyzer no longer warns about this code.

Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: msm8916: fix MMC controller aliases

[ Upstream commit b0293c19d42f6d6951c2fab9a47fed50baf2c14d ]

Change sdhcN aliases to mmcN to make them actually work. Currently the
board uses non-standard aliases sdhcN, which do not work, resulting in
mmc0 and mmc1 hosts randomly changing indices between boots.

Fixes: c4da5a561627 ("arm64: dts: qcom: Add msm8916 sdhci configuration nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201020559.1611890-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: bridge: add support for pppoe filtering

[ Upstream commit 28b78ecffea8078d81466b2e01bb5a154509f1ba ]

This makes 'bridge-nf-filter-pppoe-tagged' sysctl work for
bridged traffic.

Looking at the original commit it doesn't appear this ever worked:

 static unsigned int br_nf_post_routing(unsigned int hook, struct sk_buff **pskb,
[..]
        if (skb->protocol == htons(ETH_P_8021Q)) {
                skb_pull(skb, VLAN_HLEN);
                skb->network_header += VLAN_HLEN;
+       } else if (skb->protocol == htons(ETH_P_PPP_SES)) {
+               skb_pull(skb, PPPOE_SES_HLEN);
+               skb->network_header += PPPOE_SES_HLEN;
        }
 [..]
NF_HOOK(... POST_ROUTING, ...)

... but the adjusted offsets are never restored.

The alternative would be to rip this code out for good,
but otoh we'd have to keep this anyway for the vlan handling
(which works because vlan tag info is in the skb, not the packet
 payload).

Reported-and-tested-by: Amish Chana <amish@3g.co.za>
Fixes: 516299d2f5b6f97 ("[NETFILTER]: bridge-nf: filter bridged IPv4/IPv6 encapsulated in pppoe traffic")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: mtk-vcodec: call v4l2_m2m_ctx_release first when file is released

[ Upstream commit 9f89c881bffbdffe4060ffaef3489a2830a6dd9c ]

The func v4l2_m2m_ctx_release waits for currently running jobs
to finish and then stop streaming both queues and frees the buffers.
All this should be done before the call to mtk_vcodec_enc_release
which frees the encoder handler. This fixes null-pointer dereference bug:

[  638.028076] Mem abort info:
[  638.030932]   ESR = 0x96000004
[  638.033978]   EC = 0x25: DABT (current EL), IL = 32 bits
[  638.039293]   SET = 0, FnV = 0
[  638.042338]   EA = 0, S1PTW = 0
[  638.045474]   FSC = 0x04: level 0 translation fault
[  638.050349] Data abort info:
[  638.053224]   ISV = 0, ISS = 0x00000004
[  638.057055]   CM = 0, WnR = 0
[  638.060018] user pgtable: 4k pages, 48-bit VAs, pgdp=000000012b6db000
[  638.066485] [00000000000001a0] pgd=0000000000000000, p4d=0000000000000000
[  638.073277] Internal error: Oops: 96000004 [#1] SMP
[  638.078145] Modules linked in: rfkill mtk_vcodec_dec mtk_vcodec_enc uvcvideo mtk_mdp mtk_vcodec_common videobuf2_dma_contig v4l2_h264 cdc_ether v4l2_mem2mem videobuf2_vmalloc usbnet videobuf2_memops videobuf2_v4l2 r8152 videobuf2_common videodev cros_ec_sensors cros_ec_sensors_core industrialio_triggered_buffer kfifo_buf elan_i2c elants_i2c sbs_battery mc cros_usbpd_charger cros_ec_chardev cros_usbpd_logger crct10dif_ce mtk_vpu fuse ip_tables x_tables ipv6
[  638.118583] CPU: 0 PID: 212 Comm: kworker/u8:5 Not tainted 5.15.0-06427-g58a1d4dcfc74-dirty #109
[  638.127357] Hardware name: Google Elm (DT)
[  638.131444] Workqueue: mtk-vcodec-enc mtk_venc_worker [mtk_vcodec_enc]
[  638.137974] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[  638.144925] pc : vp8_enc_encode+0x34/0x2b0 [mtk_vcodec_enc]
[  638.150493] lr : venc_if_encode+0xac/0x1b0 [mtk_vcodec_enc]
[  638.156060] sp : ffff8000124d3c40
[  638.159364] x29: ffff8000124d3c40 x28: 0000000000000000 x27: 0000000000000000
[  638.166493] x26: 0000000000000000 x25: ffff0000e7f252d0 x24: ffff8000124d3d58
[  638.173621] x23: ffff8000124d3d58 x22: ffff8000124d3d60 x21: 0000000000000001
[  638.180750] x20: ffff80001137e000 x19: 0000000000000000 x18: 0000000000000001
[  638.187878] x17: 000000040044ffff x16: 00400032b5503510 x15: 0000000000000000
[  638.195006] x14: ffff8000118536c0 x13: ffff8000ee1da000 x12: 0000000030d4d91d
[  638.202134] x11: 0000000000000000 x10: 0000000000000980 x9 : ffff8000124d3b20
[  638.209262] x8 : ffff0000c18d4ea0 x7 : ffff0000c18d44c0 x6 : ffff0000c18d44c0
[  638.216391] x5 : ffff80000904a3b0 x4 : ffff8000124d3d58 x3 : ffff8000124d3d60
[  638.223519] x2 : ffff8000124d3d78 x1 : 0000000000000001 x0 : ffff80001137efb8
[  638.230648] Call trace:
[  638.233084]  vp8_enc_encode+0x34/0x2b0 [mtk_vcodec_enc]
[  638.238304]  venc_if_encode+0xac/0x1b0 [mtk_vcodec_enc]
[  638.243525]  mtk_venc_worker+0x110/0x250 [mtk_vcodec_enc]
[  638.248918]  process_one_work+0x1f8/0x498
[  638.252923]  worker_thread+0x140/0x538
[  638.256664]  kthread+0x148/0x158
[  638.259884]  ret_from_fork+0x10/0x20
[  638.263455] Code: f90023f9 2a0103f5 aa0303f6 aa0403f8 (f940d277)
[  638.269538] ---[ end trace e374fc10f8e181f5 ]---

[gst-master] root@debian:~/gst-build# [  638.019193] Unable to handle kernel NULL pointer dereference at virtual address 00000000000001a0
Fixes: 4e855a6efa547 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Encoder Driver")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: serial: atmel: Call dma_async_issue_pending()

[ Upstream commit 4f4b9b5895614eb2e2b5f4cab7858f44bd113e1b ]

The driver wrongly assummed that tx_submit() will start the transfer,
which is not the case, now that the at_xdmac driver is fixed. tx_submit
is supposed to push the current transaction descriptor to a pending queue,
waiting for issue_pending to be called. issue_pending must start the
transfer, not tx_submit.

Fixes: 34df42f59a60 ("serial: at91: add rx dma support")
Fixes: 08f738be88bb ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211125090028.786832-4-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: serial: atmel: Check return code of dmaengine_submit()

[ Upstream commit 1e67bd2b8cb90b66e89562598e9c2046246832d3 ]

The tx_submit() method of struct dma_async_tx_descriptor is entitled
to do sanity checks and return errors if encountered. It's not the
case for the DMA controller drivers that this client is using
(at_h/xdmac), because they currently don't do sanity checks and always
return a positive cookie at tx_submit() method. In case the controller
drivers will implement sanity checks and return errors, print a message
so that the client will be informed that something went wrong at
tx_submit() level.

Fixes: 08f738be88bb ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20211125090028.786832-3-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: qce - fix uaf on qce_ahash_register_one

[ Upstream commit b4cb4d31631912842eb7dce02b4350cbb7562d5e ]

Pointer base points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing base before free tmpl.

Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: dmxdev: fix UAF when dvb_register_device() fails

[ Upstream commit ab599eb11882f834951c436cc080c3455ba32b9b ]

I got a use-after-free report:

dvbdev: dvb_register_device: failed to create device dvb1.dvr0 (-12)
...
==================================================================
BUG: KASAN: use-after-free in dvb_dmxdev_release+0xce/0x2f0
...
Call Trace:
 dump_stack_lvl+0x6c/0x8b
 print_address_description.constprop.0+0x48/0x70
 kasan_report.cold+0x82/0xdb
 __asan_load4+0x6b/0x90
 dvb_dmxdev_release+0xce/0x2f0
...
Allocated by task 7666:
 kasan_save_stack+0x23/0x50
 __kasan_kmalloc+0x83/0xa0
 kmem_cache_alloc_trace+0x22e/0x470
 dvb_register_device+0x12f/0x980
 dvb_dmxdev_init+0x1f3/0x230
...
Freed by task 7666:
 kasan_save_stack+0x23/0x50
 kasan_set_track+0x20/0x30
 kasan_set_free_info+0x24/0x40
 __kasan_slab_free+0xf2/0x130
 kfree+0xd1/0x5c0
 dvb_register_device.cold+0x1ac/0x1fa
 dvb_dmxdev_init+0x1f3/0x230
...

When dvb_register_device() in dvb_dmxdev_init() fails, dvb_dmxdev_init()
does not return a failure, and the memory pointed to by dvbdev or
dvr_dvbdev is invalid at this point. If they are used subsequently, it
will result in UFA or null-ptr-deref.

If dvb_register_device() in dvb_dmxdev_init() fails, fix the bug by making
dvb_dmxdev_init() return an error as well.

Link: https://lore.kernel.org/linux-media/20211015085741.1203283-1-wanghai38@huawei.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: stop proccessing malicious adv data

[ Upstream commit 3a56ef719f0b9682afb8a86d64b2399e36faa4e6 ]

Syzbot reported slab-out-of-bounds read in hci_le_adv_report_evt(). The
problem was in missing validaion check.

We should check if data is not malicious and we can read next data block.
If we won't check ptr validness, code can read a way beyond skb->end and
it can cause problems, of course.

Fixes: e95beb414168 ("Bluetooth: hci_le_adv_report_evt code refactoring")
Reported-and-tested-by: syzbot+e3fcb9c4f3c2a931dc40@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: em28xx: fix memory leak in em28xx_init_dev

[ Upstream commit 22be5a10d0b24eec9e45decd15d7e6112b25f080 ]

In the em28xx_init_rev, if em28xx_audio_setup fails, this function fails
to deallocate the media_dev allocated in the em28xx_media_device_init.

Fix this by adding em28xx_unregister_media_device to free media_dev.

BTW, this patch is tested in my local syzkaller instance, and it can
prevent the memory leak from occurring again.

CC: Pavel Skripkin <paskripkin@gmail.com>
Fixes: 37ecc7b1278f ("[media] em28xx: add media controller support")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wcn36xx: Indicate beacon not connection loss on MISSED_BEACON_IND

[ Upstream commit 588b45c88ae130fe373a8c50edaf54735c3f4fe3 ]

Firmware can trigger a missed beacon indication, this is not the same as a
lost signal.

Flag to Linux the missed beacon and let the WiFi stack decide for itself if
the link is up or down by sending its own probe to determine this.

We should only be signalling the link is lost when the firmware indicates

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027232529.657764-1-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: bcm-2835: Remove rounding up the dividers

[ Upstream commit 8ca011ef4af48a7af7b15afd8a4a44039dd04cea ]

The driver, once it found a divider, tries to round it up by increasing
the least significant bit of the fractional part by one when the
round_up argument is set and there's a remainder.

However, since it increases the divider it will actually reduce the
clock rate below what we were asking for, leading to issues with
clk_set_min_rate() that will complain that our rounded clock rate is
below the minimum of the rate.

Since the dividers are fairly precise already, let's remove that part so
that we can have clk_set_min_rate() working.

This is effectively a revert of 9c95b32ca093 ("clk: bcm2835: add a round
up ability to the clock divisor").

Fixes: 9c95b32ca093 ("clk: bcm2835: add a round up ability to the clock divisor")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-3-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: bcm-2835: Pick the closest clock rate

[ Upstream commit 5517357a4733d7cf7c17fc79d0530cfa47add372 ]

The driver currently tries to pick the closest rate that is lower than
the rate being requested.

This causes an issue with clk_set_min_rate() since it actively checks
for the rounded rate to be above the minimum that was just set.

Let's change the logic a bit to pick the closest rate to the requested
rate, no matter if it's actually higher or lower.

Fixes: 6d18b8adbe67 ("clk: bcm2835: Support for clock parent selection")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-2-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: cmtp: fix possible panic when cmtp_init_sockets() fails

[ Upstream commit 2a7ca7459d905febf519163bd9e3eed894de6bb7 ]

I got a kernel BUG report when doing fault injection test:

------------[ cut here ]------------
kernel BUG at lib/list_debug.c:45!
...
RIP: 0010:__list_del_entry_valid.cold+0x12/0x4d
...
Call Trace:
 proto_unregister+0x83/0x220
 cmtp_cleanup_sockets+0x37/0x40 [cmtp]
 cmtp_exit+0xe/0x1f [cmtp]
 do_syscall_64+0x35/0xb0
 entry_SYSCALL_64_after_hwframe+0x44/0xae

If cmtp_init_sockets() in cmtp_init() fails, cmtp_init() still returns
success. This will cause a kernel bug when accessing uncreated ctmp
related data when the module exits.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller

commit e445375882883f69018aa669b67cbb37ec873406 upstream.

Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU.  Add it to the list of devices that need the
quirk.

Without this patch, device initialization fails with DMA errors:

  ata8: softreset failed (1st FIS failed)
  DMAR: DRHD: handling fault status reg 2
  DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
  DMAR: DRHD: handling fault status reg 2
  DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear

After applying the patch, the controller can be successfully initialized:

  ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
  ata8.00: ATAPI: PIONEER BD-RW   BDR-207M, 1.21, max UDMA/100
  ata8.00: configured for UDMA/100
  scsi 7:0:0:0: CD-ROM            PIONEER  BD-RW   BDR-207M 1.21 PQ: 0 ANSI: 5

Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work
Reported-by: Sam Bingner <sam@bingner.com>
Tested-by: Sam Bingner <sam@bingner.com>
Tested-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

shmem: fix a race between shmem_unused_huge_shrink and shmem_evict_inode

commit 62c9827cbb996c2c04f615ecd783ce28bcea894b upstream.

Fix a data race in commit 779750d20b93 ("shmem: split huge pages beyond
i_size under memory pressure").

Here are call traces causing race:

   Call Trace 1:
     shmem_unused_huge_shrink+0x3ae/0x410
     ? __list_lru_walk_one.isra.5+0x33/0x160
     super_cache_scan+0x17c/0x190
     shrink_slab.part.55+0x1ef/0x3f0
     shrink_node+0x10e/0x330
     kswapd+0x380/0x740
     kthread+0xfc/0x130
     ? mem_cgroup_shrink_node+0x170/0x170
     ? kthread_create_on_node+0x70/0x70
     ret_from_fork+0x1f/0x30

   Call Trace 2:
     shmem_evict_inode+0xd8/0x190
     evict+0xbe/0x1c0
     do_unlinkat+0x137/0x330
     do_syscall_64+0x76/0x120
     entry_SYSCALL_64_after_hwframe+0x3d/0xa2

A simple explanation:

Image there are 3 items in the local list (@list).  In the first
traversal, A is not deleted from @list.

  1)    A->B->C
        ^
        |
        pos (leave)

In the second traversal, B is deleted from @list.  Concurrently, A is
deleted from @list through shmem_evict_inode() since last reference
counter of inode is dropped by other thread.  Then the @list is corrupted.

  2)    A->B->C
        ^  ^
        |  |
     evict pos (drop)

We should make sure the inode is either on the global list or deleted from
any local list before iput().

Fixed by moving inodes back to global list before we put them.

[akpm@linux-foundation.org: coding style fixes]

Link: https://lkml.kernel.org/r/20211125064502.99983-1-ligang.bdlg@bytedance.com
Fixes: 779750d20b93 ("shmem: split huge pages beyond i_size under memory pressure")
Signed-off-by: Gang Li <ligang.bdlg@bytedance.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: softing_cs: softingcs_probe(): fix memleak on registration failure

commit ced4913efb0acc844ed65cc01d091a85d83a2082 upstream.

In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).

Fixes: 0a0b7a5f7a04 ("can: add driver for Softing card")
Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org
Cc: stable@vger.kernel.org # 2.6.38
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: stk1160: fix control-message timeouts

commit 6aa6e70cdb5b863a57bad61310bf89b6617a5d2d upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 9cb2173e6ea8 ("[media] media: Add stk1160 new driver (easycap replacement)")
Cc: stable@vger.kernel.org # 3.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: pvrusb2: fix control-message timeouts

commit b82bf9b9dc305d7d3d93eab106d70dbf2171b43e upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: d855497edbfb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18")
Cc: stable@vger.kernel.org # 2.6.18
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: redrat3: fix control-message timeouts

commit 2adc965c8bfa224e11ecccf9c92fd458c4236428 upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 2154be651b90 ("[media] redrat3: new rc-core IR transceiver device driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: dib0700: fix undefined behavior in tuner shutdown

commit f7b77ebe6d2f49c7747b2d619586d1aa33f9ea91 upstream.

This fixes a problem where closing the tuner would leave it in a state
where it would not tune to any channel when reopened. This problem was
discovered as part of https://github.com/hselasky/webcamd/issues/16.

Since adap->id is 0 or 1, this bit-shift overflows, which is undefined
behavior. The driver still worked in practice as the overflow would in
most environments result in 0, which rendered the line a no-op. When
running the driver as part of webcamd however, the overflow could lead
to 0xff due to optimizations by the compiler, which would, in the end,
improperly shut down the tuner.

The bug is a regression introduced in the commit referenced below. The
present patch causes identical behavior to before that commit for
adap->id equal to 0 or 1. The driver does not contain support for
dib0700 devices with more adapters, assuming such even exist.

Tests have been performed with the Xbox One Digital TV Tuner on amd64.
Not all dib0700 devices are expected to be affected by the regression;
this code path is only taken by those with incorrect endpoint numbers.

Link: https://lore.kernel.org/linux-media/1d2fc36d94ced6f67c7cc21dcc469d5e5bdd8201.1632689033.git.mchehab+huawei@kernel.org
Cc: stable@vger.kernel.org
Fixes: 7757ddda6f4f ("[media] DiB0700: add function to change I2C-speed")
Signed-off-by: Michael Kuron <michael.kuron@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: s2255: fix control-message timeouts

commit f71d272ad4e354097020a4e6b1dc6e4b59feb50f upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Use the common control-message timeout define for the five-second
timeouts.

Fixes: 38f993ad8b1f ("V4L/DVB (8125): This driver adds support for the Sensoray 2255 devices.")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: cpia2: fix control-message timeouts

commit 10729be03327f53258cb196362015ad5c6eabe02 upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: ab33d5071de7 ("V4L/DVB (3376): Add cpia2 camera support")
Cc: stable@vger.kernel.org # 2.6.17
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: em28xx: fix control-message timeouts

commit d9b7e8df3aa9b8c10708aab60e72e79ac08237e4 upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: a6c2ba283565 ("[PATCH] v4l: 716: support for em28xx board family")
Cc: stable@vger.kernel.org # 2.6.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: mceusb: fix control-message timeouts

commit 16394e998cbb050730536bdf7e89f5a70efbd974 upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 66e89522aff7 ("V4L/DVB: IR: add mceusb IR receiver driver")
Cc: stable@vger.kernel.org # 2.6.36
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: flexcop-usb: fix control-message timeouts

commit cd1798a387825cc4a51282f5a611ad05bb1ad75f upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Note that the driver was multiplying some of the timeout values with HZ
twice resulting in 3000-second timeouts with HZ=1000.

Also note that two of the timeout defines are currently unused.

Fixes: 2154be651b90 ("[media] redrat3: new rc-core IR transceiver device driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: cmos: take rtc_lock while reading from CMOS

commit 454f47ff464325223129b9b5b8d0b61946ec704d upstream.

Reading from the CMOS involves writing to the index register and then
reading from the data register. Therefore access to the CMOS has to be
serialized with rtc_lock. This invocation of CMOS_READ was not
serialized, which could cause trouble when other code is accessing CMOS
at the same time.

Use spin_lock_irq() like the rest of the function.

Nothing in kernel modifies the RTC_DM_BINARY bit, so there could be a
separate pair of spin_lock_irq() / spin_unlock_irq() before doing the
math.

Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-2-mat.jonczyk@o2.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind()

commit dded08927ca3c31a5c37f8e7f95fe98770475dd4 upstream.

Syzbot detected a NULL pointer dereference of nfc_llcp_sock->dev pointer
(which is a 'struct nfc_dev *') with calls to llcp_sock_sendmsg() after
a failed llcp_sock_bind(). The message being sent is a SOCK_DGRAM.

KASAN report:

  BUG: KASAN: null-ptr-deref in nfc_alloc_send_skb+0x2d/0xc0
  Read of size 4 at addr 00000000000005c8 by task llcp_sock_nfc_a/899

  CPU: 5 PID: 899 Comm: llcp_sock_nfc_a Not tainted 5.16.0-rc6-next-20211224-00001-gc6437fbf18b0 #125
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
  Call Trace:
   <TASK>
   dump_stack_lvl+0x45/0x59
   ? nfc_alloc_send_skb+0x2d/0xc0
   __kasan_report.cold+0x117/0x11c
   ? mark_lock+0x480/0x4f0
   ? nfc_alloc_send_skb+0x2d/0xc0
   kasan_report+0x38/0x50
   nfc_alloc_send_skb+0x2d/0xc0
   nfc_llcp_send_ui_frame+0x18c/0x2a0
   ? nfc_llcp_send_i_frame+0x230/0x230
   ? __local_bh_enable_ip+0x86/0xe0
   ? llcp_sock_connect+0x470/0x470
   ? llcp_sock_connect+0x470/0x470
   sock_sendmsg+0x8e/0xa0
   ____sys_sendmsg+0x253/0x3f0
   ...

The issue was visible only with multiple simultaneous calls to bind() and
sendmsg(), which resulted in most of the bind() calls to fail.  The
bind() was failing on checking if there is available WKS/SDP/SAP
(respective bit in 'struct nfc_llcp_local' fields).  When there was no
available WKS/SDP/SAP, the bind returned error but the sendmsg() to such
socket was able to trigger mentioned NULL pointer dereference of
nfc_llcp_sock->dev.

The code looks simply racy and currently it protects several paths
against race with checks for (!nfc_llcp_sock->local) which is NULL-ified
in error paths of bind().  The llcp_sock_sendmsg() did not have such
check but called function nfc_llcp_send_ui_frame() had, although not
protected with lock_sock().

Therefore the race could look like (same socket is used all the time):
  CPU0                                     CPU1
  ====                                     ====
  llcp_sock_bind()
  - lock_sock()
    - success
  - release_sock()
  - return 0
                                           llcp_sock_sendmsg()
                                           - lock_sock()
                                           - release_sock()
  llcp_sock_bind(), same socket
  - lock_sock()
    - error
                                           - nfc_llcp_send_ui_frame()
                                             - if (!llcp_sock->local)
    - llcp_sock->local = NULL
    - nfc_put_device(dev)
                                             - dereference llcp_sock->dev
  - release_sock()
  - return -ERRNO

The nfc_llcp_send_ui_frame() checked llcp_sock->local outside of the
lock, which is racy and ineffective check.  Instead, its caller
llcp_sock_sendmsg(), should perform the check inside lock_sock().

Reported-and-tested-by: syzbot+7f23bcddf626e0593a39@syzkaller.appspotmail.com
Fixes: b874dec21d1c ("NFC: Implement LLCP connection less Tx path")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: wacom: Avoid using stale array indicies to read contact count

commit 20f3cf5f860f9f267a6a6e5642d3d0525edb1814 upstream.

If we ever see a touch report with contact count data we initialize
several variables used to read the contact count in the pre-report
phase. These variables are never reset if we process a report which
doesn't contain a contact count, however. This can cause the pre-
report function to trigger a read of arbitrary memory (e.g. NULL
if we're lucky) and potentially crash the driver.

This commit restores resetting of the variables back to default
"none" values that were used prior to the commit mentioned
below.

Link: https://github.com/linuxwacom/input-wacom/issues/276
Fixes: 003f50ab673c (HID: wacom: Update last_slot_field during pre_report phase)
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: wacom: Ignore the confidence flag when a touch is removed

commit df03e9bd6d4806619b4cdc91a3d7695818a8e2b7 upstream.

AES hardware may internally re-classify a contact that it thought was
intentional as a palm. Intentional contacts are reported as "down" with
the confidence bit set. When this re-classification occurs, however, the
state transitions to "up" with the confidence bit cleared. This kind of
transition appears to be legal according to Microsoft docs, but we do
not handle it correctly. Because the confidence bit is clear, we don't
call `wacom_wac_finger_slot` and update userspace. This causes hung
touches that confuse userspace and interfere with pen arbitration.

This commit adds a special case to ignore the confidence flag if a contact
is reported as removed. This ensures we do not leave a hung touch if one
of these re-classification events occured. Ideally we'd have some way to
also let userspace know that the touch has been re-classified as a palm
and needs to be canceled, but that's not possible right now :)

Link: https://github.com/linuxwacom/input-wacom/issues/288
Fixes: 7fb0413baa7f (HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts)
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: uhid: Fix worker destroying device without any protection

commit 4ea5763fb79ed89b3bdad455ebf3f33416a81624 upstream.

uhid has to run hid_add_device() from workqueue context while allowing
parallel use of the userspace API (which is protected with ->devlock).
But hid_add_device() can fail. Currently, that is handled by immediately
destroying the associated HID device, without using ->devlock - but if
there are concurrent requests from userspace, that's wrong and leads to
NULL dereferences and/or memory corruption (via use-after-free).

Fix it by leaving the HID device as-is in the worker. We can clean it up
later, either in the UHID_DESTROY command handler or in the ->release()
handler.

Cc: stable@vger.kernel.org
Fixes: 67f8ecc550b5 ("HID: uhid: fix timeout when probe races with IO")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: fix init and cleanup of sco_conn.timeout_work

commit 49d8a5606428ca0962d09050a5af81461ff90fbb upstream.

Before freeing struct sco_conn, all delayed timeout work should be
cancelled. Otherwise, sco_sock_timeout could potentially use the
sco_conn after it has been freed.

Additionally, sco_conn.timeout_work should be initialized when the
connection is allocated, not when the channel is added. This is
because an sco_conn can create channels with multiple sockets over its
lifetime, which happens if sockets are released but the connection
isn't deleted.

Fixes: ba316be1b6a0 ("Bluetooth: schedule SCO timeouts with delayed_work")
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
[OP: adjusted context for 4.14]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: schedule SCO timeouts with delayed_work

commit ba316be1b6a00db7126ed9a39f9bee434a508043 upstream.

struct sock.sk_timer should be used as a sock cleanup timer. However,
SCO uses it to implement sock timeouts.

This causes issues because struct sock.sk_timer's callback is run in
an IRQ context, and the timer callback function sco_sock_timeout takes
a spin lock on the socket. However, other functions such as
sco_conn_del and sco_conn_ready take the spin lock with interrupts
enabled.

This inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} lock usage could
lead to deadlocks as reported by Syzbot [1]:
       CPU0
       ----
  lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
  <Interrupt>
    lock(slock-AF_BLUETOOTH-BTPROTO_SCO);

To fix this, we use delayed work to implement SCO sock timouts
instead. This allows us to avoid taking the spin lock on the socket in
an IRQ context, and corrects the misuse of struct sock.sk_timer.

As a note, cancel_delayed_work is used instead of
cancel_delayed_work_sync in sco_sock_set_timer and
sco_sock_clear_timer to avoid a deadlock. In the future, the call to
bh_lock_sock inside sco_sock_timeout should be changed to lock_sock to
synchronize with other functions using lock_sock. However, since
sco_sock_set_timer and sco_sock_clear_timer are sometimes called under
the locked socket (in sco_connect and __sco_sock_close),
cancel_delayed_work_sync might cause them to sleep until an
sco_sock_timeout that has started finishes running. But
sco_sock_timeout would also sleep until it can grab the lock_sock.

Using cancel_delayed_work is fine because sco_sock_timeout does not
change from run to run, hence there is no functional difference
between:
1. waiting for a timeout to finish running before scheduling another
timeout
2. scheduling another timeout while a timeout is running.

Link: https://syzkaller.appspot.com/bug?id=9089d89de0502e120f234ca0fc8a703f7368b31e
Reported-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Tested-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
[OP: adjusted context for 4.14]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Fix WARNING when calling local_irq_restore() with interrupts enabled

commit 8b144dedb928e4e2f433a328d58f44c3c098d63e upstream.

Syzbot reports the following WARNING:

[200~raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 1 PID: 1206 at kernel/locking/irqflag-debug.c:10
   warn_bogus_irq_restore+0x1d/0x20 kernel/locking/irqflag-debug.c:10

Hardware initialization for the rtl8188cu can run for as long as 350 ms,
and the routine may be called with interrupts disabled. To avoid locking
the machine for this long, the current routine saves the interrupt flags
and enables local interrupts. The problem is that it restores the flags
at the end without disabling local interrupts first.

This patch fixes commit a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long
disable of IRQs").

Reported-by: syzbot+cce1ee31614c171f5595@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long disable of IRQs")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215171105.20623-1-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: uvcvideo: fix division by zero at stream start

commit 8aa637bf6d70d2fb2ad4d708d8b9dd02b1c095df upstream.

Add the missing bulk-endpoint max-packet sanity check to
uvc_video_start_transfer() to avoid division by zero in
uvc_alloc_urb_buffers() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).

Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).

Fixes: c0efd232929c ("V4L/DVB (8145a): USB Video Class driver")
Cc: stable@vger.kernel.org # 2.6.26
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

orangefs: Fix the size of a memory allocation in orangefs_bufmap_alloc()

commit 40a74870b2d1d3d44e13b3b73c6571dd34f5614d upstream.

'buffer_index_array' really looks like a bitmap. So it should be allocated
as such.
When kzalloc is called, a number of bytes is expected, but a number of
longs is passed instead.

In get(), if not enough memory is allocated, un-allocated memory may be
read or written.

So use bitmap_zalloc() to safely allocate the correct memory size and
avoid un-expected behavior.

While at it, change the corresponding kfree() into bitmap_free() to keep
the semantic.

Fixes: ea2c9c9f6574 ("orangefs: bufmap rewrite")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Avoid bitwise vs logical OR warning in snb_wm_latency_quirk()

commit 2e70570656adfe1c5d9a29940faa348d5f132199 upstream.

A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean types:

drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
        changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
                  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

This construct is intentional, as it allows every one of the calls to
ilk_increase_wm_latency() to occur (instead of short circuiting with
logical OR) while still caring about the result of each call.

To make this clearer to the compiler, use the '|=' operator to assign
the result of each ilk_increase_wm_latency() call to changed, which
keeps the meaning of the code the same but makes it obvious that every
one of these calls is expected to happen.

Link: https://github.com/ClangBuiltLinux/linux/issues/1473
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Dávid Bolvanský <david.bolvansky@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014211916.3550122-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wlan-ng: Avoid bitwise vs logical OR warning in hfa384x_usb_throttlefn()

commit 502408a61f4b7eb4713f44bd77f4a48e6cb1b59a upstream.

A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean expressions:

In file included from drivers/staging/wlan-ng/prism2usb.c:2:
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
            ((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
            ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning
1 warning generated.

The comment explains that short circuiting here is undesirable, as the
calls to test_and_{clear,set}_bit() need to happen for both sides of the
expression.

Clang's suggestion would work to silence the warning but the readability
of the expression would suffer even more. To clean up the warning and
make the block more readable, use a variable for each side of the
bitwise expression.

Link: https://github.com/ClangBuiltLinux/linux/issues/1478
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211014215703.3705371-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

random: fix data race on crng init time

commit 009ba8568be497c640cab7571f7bfd18345d7b24 upstream.

_extract_crng() does plain loads of crng->init_time and
crng_global_init_time, which causes undefined behavior if
crng_reseed() and RNDRESEEDCRNG modify these corrently.

Use READ_ONCE() and WRITE_ONCE() to make the behavior defined.

Don't fix the race on crng->init_time by protecting it with crng->lock,
since it's not a problem for duplicate reseedings to occur.  I.e., the
lockless access with READ_ONCE() is fine.

Fixes: d848e5f8e1eb ("random: add new ioctl RNDRESEEDCRNG")
Fixes: e192be9d9a30 ("random: replace non-blocking pool with a Chacha20-based CRNG")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

random: fix data race on crng_node_pool

commit 5d73d1e320c3fd94ea15ba5f79301da9a8bcc7de upstream.

extract_crng() and crng_backtrack_protect() load crng_node_pool with a
plain load, which causes undefined behavior if do_numa_crng_init()
modifies it concurrently.

Fix this by using READ_ONCE().  Note: as per the previous discussion
https://lore.kernel.org/lkml/20211219025139.31085-1-ebiggers@kernel.org/T/#u,
READ_ONCE() is believed to be sufficient here, and it was requested that
it be used here instead of smp_load_acquire().

Also change do_numa_crng_init() to set crng_node_pool using
cmpxchg_release() instead of mb() + cmpxchg(), as the former is
sufficient here but is more lightweight.

Fixes: 1e7f583af67b ("random: make /dev/urandom scalable for silly userspace programs")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: gs_usb: gs_can_start_xmit(): zero-initialize hf->{flags,reserved}

commit 89d58aebe14a365c25ba6645414afdbf4e41cea4 upstream.

No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.

While there also initialize the reserved member with 0.

Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220106002952.25883-1-brian.silverman@bluerivertech.com
Link: https://github.com/candle-usb/candleLight_fw/issues/87
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
[mkl: initialize the reserved member, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: gs_usb: fix use of uninitialized variable, detach device on reception of invalid USB data

commit 4a8737ff068724f509d583fef404d349adba80d6 upstream.

The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.

This fixes the error found by clang:

| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
|                                     uninitialized whenever 'if' condition is true
|         if (hf->channel >= GS_MAX_INTF)
|             ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
|                           hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
|                               ^~~

Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mfd: intel-lpss: Fix too early PM enablement in the ACPI ->probe()

commit c9e143084d1a602f829115612e1ec79df3727c8b upstream.

The runtime PM callback may be called as soon as the runtime PM facility
is enabled and activated. It means that ->suspend() may be called before
we finish probing the device in the ACPI case. Hence, NULL pointer
dereference:

  intel-lpss INT34BA:00: IRQ index 0 not found
  BUG: kernel NULL pointer dereference, address: 0000000000000030
  ...
  Workqueue: pm pm_runtime_work
  RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]

To fix this, first try to register the device and only after that enable
runtime PM facility.

Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Reported-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>