rtc: set the alarm to the next expiring timer

[ Upstream commit 74717b28cb32e1ad3c1042cafd76b264c8c0f68d ]

If there is any non expired timer in the queue, the RTC alarm is never set.
This is an issue when adding a timer that expires before the next non
expired timer.

Ensure the RTC alarm is set in that case.

Fixes: 2b2f5ff00f63 ("rtc: interface: ignore expired timers when enqueuing new timers")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: fix under-evaluated ssthresh in TCP Vegas

[ Upstream commit cf5d74b85ef40c202c76d90959db4d850f301b95 ]

With the commit 76174004a0f19785 (tcp: do not slow start when cwnd equals
ssthresh), the comparison to the reduced cwnd in tcp_vegas_ssthresh() would
under-evaluate the ssthresh.

Signed-off-by: Hoang Tran <hoang.tran@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fm10k: ensure we process SM mbx when processing VF mbx

[ Upstream commit 17a91809942ca32c70026d2d5ba3348a2c4fdf8f ]

When we process VF mailboxes, the driver is likely going to also queue
up messages to the switch manager. This process merely queues up the
FIFO, but doesn't actually begin the transmission process. Because we
hold the mailbox lock during this VF processing, the PF<->SM mailbox is
not getting processed at this time. Ensure that we actually process the
PF<->SM mailbox in between each PF<->VF mailbox.

This should ensure prompt transmission of the messages queued up after
each VF message is received and handled.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: PLOGI failures during NPIV testing

[ Upstream commit e8bcf0ae4c0346fdc78ebefe0eefcaa6a6622d38 ]

Local Reject/Invalid RPI errors seen during discovery.

Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.

Adjust the test for whether cleanup is necessary.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: Fix secure firmware updates

[ Upstream commit 184fc2b9a8bcbda9c14d0a1e7fbecfc028c7702e ]

Firmware update fails with: status x17 add_status x56 on the final write

If multiple DMA buffers are used for the download, some firmware revs
have difficulty with signatures and crcs split across the dma buffer
boundaries.  Resolve by making all writes be a single 4k page in length.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/AER: Report non-fatal errors only to the affected endpoint

[ Upstream commit 86acc790717fb60fb51ea3095084e331d8711c74 ]

Previously, if an non-fatal error was reported by an endpoint, we
called report_error_detected() for the endpoint, every sibling on the
bus, and their descendents.  If any of them did not implement the
.error_detected() method, do_recovery() failed, leaving all these
devices unrecovered.

For example, the system described in the bugzilla below has two devices:

  0000:74:02.0 [19e5:a230] SAS controller, driver has .error_detected()
  0000:74:03.0 [19e5:a235] SATA controller, driver lacks .error_detected()

When a device such as 74:02.0 reported a non-fatal error, do_recovery()
failed because 74:03.0 lacked an .error_detected() method.  But per PCIe
r3.1, sec 6.2.2.2.2, such an error does not compromise the Link and
does not affect 74:03.0:

  Non-fatal errors are uncorrectable errors which cause a particular
  transaction to be unreliable but the Link is otherwise fully functional.
  Isolating Non-fatal from Fatal errors provides Requester/Receiver logic
  in a device or system management software the opportunity to recover from
  the error without resetting the components on the Link and disturbing
  other transactions in progress.  Devices not associated with the
  transaction in error are not impacted by the error.

Report non-fatal errors only to the endpoint that reported them.  We really
want to check for AER_NONFATAL here, but the current code structure doesn't
allow that.  Looking for pci_channel_io_normal is the best we can do now.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=197055
Fixes: 6c2b374d7485 ("PCI-Express AER implemetation: AER core and aerdriver")
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ixgbe: fix use of uninitialized padding

[ Upstream commit dcfd6b839c998bc9838e2a47f44f37afbdf3099c ]

This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.

- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()

- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

igb: check memory allocation failure

[ Upstream commit 18eb86362a52f0af933cc0fd5e37027317eb2d1c ]

Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.

This avoids NULL pointers dereference.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Create SR-IOV virtfn/physfn links before attaching driver

[ Upstream commit 27d6162944b9b34c32cd5841acd21786637ee743 ]

When creating virtual functions, create the "virtfn%u" and "physfn" links
in sysfs *before* attaching the driver instead of after.  When we attach
the driver to the new virtual network interface first, there is a race when
the driver attaches to the new sends out an "add" udev event, and the
network interface naming software (biosdevname or systemd, for example)
tries to look at these links.

Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mpt3sas: Fix IO error occurs on pulling out a drive from RAID1 volume created on two SATA drive

[ Upstream commit 2ce9a3645299ba1752873d333d73f67620f4550b ]

Whenever an I/O for a RAID volume fails with IOCStatus
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and SCSIStatus equal to
(MPI2_SCSI_STATE_TERMINATED | MPI2_SCSI_STATE_NO_SCSI_STATUS) then
return the I/O to SCSI midlayer with "DID_RESET" (i.e. retry the IO
infinite times) set in the host byte.

Previously, the driver was completing the I/O with "DID_SOFT_ERROR"
which causes the I/O to be quickly retried. However, firmware needed
more time and hence I/Os were failing.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: cxgb4i: fix Tx skb leak

[ Upstream commit 9b3a081fb62158b50bcc90522ca2423017544367 ]

In case of connection reset Tx skb queue can have some skbs which are
not transmitted so purge Tx skb queue in release_offload_resources() to
avoid skb leak.

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Avoid bus reset if bridge itself is broken

[ Upstream commit 357027786f3523d26f42391aa4c075b8495e5d28 ]

When checking to see if a PCI bus can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set.  Children marked with that flag are known not to behave well
after a bus reset.

Some PCIe root port bridges also do not behave well after a bus reset,
sometimes causing the devices behind the bridge to become unusable.

Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to allow these bridges to be flagged, and prevent their secondary buses
from being reset.

Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: at803x: Change error to EINVAL for invalid MAC

[ Upstream commit fc7556877d1748ac00958822a0a3bba1d4bd9e0d ]

Change the return error code to EINVAL if the MAC
address is not valid in the set_wol function.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: pl031: make interrupt optional

[ Upstream commit 5b64a2965dfdfca8039e93303c64e2b15c19ff0c ]

On some platforms, the interrupt for the PL031 is optional.  Avoid
trying to claim the interrupt if it's not specified.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: crypto4xx - increase context and scatter ring buffer elements

[ Upstream commit 778f81d6cdb7d25360f082ac0384d5103f04eca5 ]

If crypto4xx is used in conjunction with dm-crypt, the available
ring buffer elements are not enough to handle the load properly.

On an aes-cbc-essiv:sha256 encrypted swap partition the read
performance is abyssal: (tested with hdparm -t)

/dev/mapper/swap_crypt:
 Timing buffered disk reads:  14 MB in  3.68 seconds =   3.81 MB/sec

The patch increases both PPC4XX_NUM_SD and PPC4XX_NUM_PD to 256.
This improves the performance considerably:

/dev/mapper/swap_crypt:
 Timing buffered disk reads: 104 MB in  3.03 seconds =  34.31 MB/sec

Furthermore, PPC4XX_LAST_SD, PPC4XX_LAST_GD and PPC4XX_LAST_PD
can be easily calculated from their respective PPC4XX_NUM_*
constant.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

backlight: pwm_bl: Fix overflow condition

[ Upstream commit 5d0c49acebc9488e37db95f1d4a55644e545ffe7 ]

This fixes an overflow condition that can happen with high max
brightness and period values in compute_duty_cycle. This fixes it by
using a 64 bit variable for computing the duty cycle.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Fix NULL pointer dereference in reopen failure path

[ Upstream commit 2247925f0942dc4e7c09b1cde45ca18461d94c5f ]

Net device reset can fail when the h/w or f/w is in a bad state.
Subsequent netdevice open fails in bnxt_hwrm_stat_ctx_alloc().
The cleanup invokes bnxt_hwrm_resource_free() which inturn
calls bnxt_disable_int().  In this routine, the code segment

if (ring->fw_ring_id != INVALID_HW_RING_ID)
   BNXT_CP_DB(cpr->cp_doorbell, cpr->cp_raw_cons);

results in NULL pointer dereference as cpr->cp_doorbell is not yet
initialized, and fw_ring_id is zero.

The fix is to initialize cpr fw_ring_id to INVALID_HW_RING_ID before
bnxt_init_chip() is invoked.

Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpuidle: powernv: Pass correct drv->cpumask for registration

[ Upstream commit 293d264f13cbde328d5477f49e3103edbc1dc191 ]

drv->cpumask defaults to cpu_possible_mask in __cpuidle_driver_init().
On PowerNV platform cpu_present could be less than cpu_possible in cases
where firmware detects the cpu, but it is not available to the OS.  When
CONFIG_HOTPLUG_CPU=n, such cpus are not hotplugable at runtime and hence
we skip creating cpu_device.

This breaks cpuidle on powernv where register_cpu() is not called for
cpus in cpu_possible_mask that cannot be hot-added at runtime.

Trying cpuidle_register_device() on cpu without cpu_device will cause
crash like this:

cpu 0xf: Vector: 380 (Data SLB Access) at [c000000ff1503490]
    pc: c00000000022c8bc: string+0x34/0x60
    lr: c00000000022ed78: vsnprintf+0x284/0x42c
    sp: c000000ff1503710
   msr: 9000000000009033
   dar: 6000000060000000
  current = 0xc000000ff1480000
  paca    = 0xc00000000fe82d00   softe: 0        irq_happened: 0x01
    pid   = 1, comm = swapper/8
Linux version 4.11.0-rc2 (sv@sagarika) (gcc version 4.9.4
(Buildroot 2017.02-00004-gc28573e) ) #15 SMP Fri Mar 17 19:32:02 IST 2017
enter ? for help
[link register   ] c00000000022ed78 vsnprintf+0x284/0x42c
[c000000ff1503710] c00000000022ebb8 vsnprintf+0xc4/0x42c (unreliable)
[c000000ff1503800] c00000000022ef40 vscnprintf+0x20/0x44
[c000000ff1503830] c0000000000ab61c vprintk_emit+0x94/0x2cc
[c000000ff15038a0] c0000000000acc9c vprintk_func+0x60/0x74
[c000000ff15038c0] c000000000619694 printk+0x38/0x4c
[c000000ff15038e0] c000000000224950 kobject_get+0x40/0x60
[c000000ff1503950] c00000000022507c kobject_add_internal+0x60/0x2c4
[c000000ff15039e0] c000000000225350 kobject_init_and_add+0x70/0x78
[c000000ff1503a60] c00000000053c288 cpuidle_add_sysfs+0x9c/0xe0
[c000000ff1503ae0] c00000000053aeac cpuidle_register_device+0xd4/0x12c
[c000000ff1503b30] c00000000053b108 cpuidle_register+0x98/0xcc
[c000000ff1503bc0] c00000000085eaf0 powernv_processor_idle_init+0x140/0x1e0
[c000000ff1503c60] c00000000000cd60 do_one_initcall+0xc0/0x15c
[c000000ff1503d20] c000000000833e84 kernel_init_freeable+0x1a0/0x25c
[c000000ff1503dc0] c00000000000d478 kernel_init+0x24/0x12c
[c000000ff1503e30] c00000000000b564 ret_from_kernel_thread+0x5c/0x78

This patch fixes the bug by passing correct cpumask from
powernv-cpuidle driver.

Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
[ rjw: Comment massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dma-mapping: disallow dma_get_sgtable() for non-kernel managed memory

[ Upstream commit 916a008b4b8ecc02fbd035cfb133773dba1ff3d7 ]

dma_get_sgtable() tries to create a scatterlist table containing valid
struct page pointers for the coherent memory allocation passed in to it.

However, memory can be declared via dma_declare_coherent_memory(), or
via other reservation schemes which means that coherent memory is not
guaranteed to be backed by struct pages.  In such cases, the resulting
scatterlist table contains pointers to invalid pages, which causes
kernel oops later.

This patch adds detection of such memory, and refuses to create a
scatterlist table for such memory.

Reported-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nfnetlink_queue: fix secctx memory leak

[ Upstream commit 77c1c03c5b8ef28e55bb0aff29b1e006037ca645 ]

We must call security_release_secctx to free the memory returned by
security_secid_to_secctx, otherwise memory may be leaked forever.

Fixes: ef493bd930ae ("netfilter: nfnetlink_queue: add security context information")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: plat: Register shutdown for xhci_plat

[ Upstream commit b07c12517f2aed0add8ce18146bb426b14099392 ]

Shutdown should be called for xhci_plat devices especially for
situations where kexec might be used by stopping DMA
transactions.

Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

isdn: kcapi: avoid uninitialized data

[ Upstream commit af109a2cf6a9a6271fa420ae2d64d72d86c92b7d ]

gcc-7 points out that the AVMB1_ADDCARD ioctl results in an unintialized
value ending up in the cardnr parameter:

drivers/isdn/capi/kcapi.c: In function 'old_capi_manufacturer':
drivers/isdn/capi/kcapi.c:1042:24: error: 'cdef.cardnr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
   cparams.cardnr = cdef.cardnr;

This has been broken since before the start of the git history, so
either the value is not used for anything important, or the ioctl
command doesn't get called in practice.

Setting the cardnr to zero avoids the warning and makes sure
we have consistent behavior.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: pci-assign: do not map smm memory slot pages in vt-d page tables

[ Upstream commit 0292e169b2d9c8377a168778f0b16eadb1f578fd ]

or VM memory are not put thus leaked in kvm_iommu_unmap_memslots() when
destroy VM.

This is consistent with current vfio implementation.

Signed-off-by: herongguang <herongguang.he@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend

[ Upstream commit 9bcf53f34a2c1cebc45cc12e273dcd5f51fbc099 ]

mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_nat_snmp: Fix panic when snmp_trap_helper fails to register

[ Upstream commit 75c689dca98851d65ef5a27e5ce26b625b68751c ]

In the commit 93557f53e1fb ("netfilter: nf_conntrack: nf_conntrack snmp
helper"), the snmp_helper is replaced by nf_nat_snmp_hook. So the
snmp_helper is never registered. But it still tries to unregister the
snmp_helper, it could cause the panic.

Now remove the useless snmp_helper and the unregister call in the
error handler.

Fixes: 93557f53e1fb ("netfilter: nf_conntrack: nf_conntrack snmp helper")
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nfnl_cthelper: fix a race when walk the nf_ct_helper_hash table

[ Upstream commit 83d90219a5df8d950855ce73229a97b63605c317 ]

The nf_ct_helper_hash table is protected by nf_ct_helper_mutex, while
nfct_helper operation is protected by nfnl_lock(NFNL_SUBSYS_CTHELPER).
So it's possible that one CPU is walking the nf_ct_helper_hash for
cthelper add/get/del, another cpu is doing nf_conntrack_helpers_unregister
at the same time. This is dangrous, and may cause use after free error.

Note, delete operation will flush all cthelpers added via nfnetlink, so
using rcu to do protect is not easy.

Now introduce a dummy list to record all the cthelpers added via
nfnetlink, then we can walk the dummy list instead of walking the
nf_ct_helper_hash. Also, keep nfnl_cthelper_dump_table unchanged, it
may be invoked without nfnl_lock(NFNL_SUBSYS_CTHELPER) held.

Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irda: vlsi_ir: fix check for DMA mapping errors

[ Upstream commit 6ac3b77a6ffff7513ff86b684aa256ea01c0e5b5 ]

vlsi_alloc_ring() checks for DMA mapping errors by comparing
returned address with zero, while pci_dma_mapping_error() should be used.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/iser: Fix possible mr leak on device removal event

[ Upstream commit ea174c9573b0e0c8bc1a7a90fe9360ccb7aa9cbb ]

When the rdma device is removed, we must cleanup all
the rdma resources within the DEVICE_REMOVAL event
handler to let the device teardown gracefully. When
this happens with live I/O, some memory regions are
occupied. Thus, track them too and dereg all the mr's.

We are safe with mr access by iscsi_iser_cleanup_task.

Reported-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: Do not enable NAPI on q_vectors that have no rings

[ Upstream commit 13a8cd191a2b470cfd435b3b57dbd21aa65ff78c ]

When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error.  To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Do not allow negative values for busy_read and busy_poll sysctl interfaces

[ Upstream commit 95f255211396958c718aef8c45e3923b5211ea7b ]

This change basically codifies what I think was already the limitations on
the busy_poll and busy_read sysctl interfaces.  We weren't checking the
lower bounds and as such could input negative values. The behavior when
that was used was dependent on the architecture. In order to prevent any
issues with that I am just disabling support for values less than 0 since
this way we don't have to worry about any odd behaviors.

By limiting the sysctl values this way it also makes it consistent with how
we handle the SO_BUSY_POLL socket option since the value appears to be
reported as a signed integer value and negative values are rejected.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bna: avoid writing uninitialized data into hw registers

[ Upstream commit a5af83925363eb85d467933e3d6ec5a87001eb7c ]

The latest gcc-7 snapshot warns about bfa_ioc_send_enable/bfa_ioc_send_disable
writing undefined values into the hardware registers:

drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function 'bfa_iocpf_sm_disabling_entry':
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+4)' is used uninitialized in this function [-Werror=uninitialized]
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+8)' is used uninitialized in this function [-Werror=uninitialized]

The two functions look like they should do the same thing, but only one
of them initializes the time stamp and clscode field. The fact that we
only get a warning for one of the two functions seems to be arbitrary,
based on the inlining decisions in the compiler.

To address this, I'm making both functions do the same thing:

- set the clscode from the ioc structure in both
- set the time stamp from ktime_get_real_seconds (which also
  avoids the signed-integer overflow in 2038 and extends the
  well-defined behavior until 2106).
- zero-fill the reserved field

Fixes: 8b230ed8ec96 ("bna: Brocade 10Gb Ethernet device driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/qeth: no ETH header for outbound AF_IUCV

[ Upstream commit acd9776b5c45ef02d1a210969a6fcc058afb76e3 ]

With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte
slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr()
fills this ETH header... and then immediately moves it to the
skb's headroom, where it disappears and is never seen again.

But it's still possible for us to return NETDEV_TX_BUSY after the skb has
been modified. Since we didn't get a private copy of the skb, the next
time the skb is delivered to hard_start_xmit() it no longer has the
expected layout (we moved the ETH header to the headroom, so skb->data
now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr()
does another round of rebuilding, the resulting qeth header ends up
all wrong. On transmission, the buffer is then rejected by
the HiperSockets device with SBALF15 = x'04'.
When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it
tears down the offending socket.

As the ETH header for AF_IUCV serves no purpose, just align the code to
what we do for IP traffic on L3 HiperSockets: keep the ETH header at
skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer().
When mapping the payload into the SBAL elements, the ETH header is then
stripped off. This avoids the skb manipulations in
qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit()
after NETDEV_TX_BUSY is now processed properly.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

r8152: prevent the driver from transmitting packets with carrier off

[ Upstream commit 2f25abe6bac573928a990ccbdac75873add8127e ]

The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.

The another similar case is
 1. unplug the cable.
 2. interrupt transfer queue a work_queue for linking change.
 3. device enters the ALDPS mode.
 4. a tx occurs before the work_queue is called.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: xinmo: fix for out of range for THT 2P arcade controller.

[ Upstream commit 9257821c5a1dc57ef3a37f7cbcebaf548395c964 ]

There is a new clone of the XIN MO arcade controller which has same issue with
out of range like the original.  This fix will solve the issue where 2
directions on the joystick are not recognized by the new THT 2P arcade
controller with device ID 0x75e1.  In details the new device ID is added the
hid-id list and the hid-xinmo source code.

Signed-off-by: Peter Stein <peter@stuntstein.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (asus_atk0110) fix uninitialized data access

[ Upstream commit a2125d02443e9a4e68bcfd9f8004fa23239e8329 ]

The latest gcc-7 snapshot adds a warning to point out that when
atk_read_value_old or atk_read_value_new fails, we copy
uninitialized data into sensor->cached_value:

drivers/hwmon/asus_atk0110.c: In function 'atk_input_show':
drivers/hwmon/asus_atk0110.c:651:26: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized]

Adding an error check avoids this. All versions of the driver
are affected.

Fixes: 2c03d07ad54d ("hwmon: Add Asus ATK0110 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: ti: fix PCI bus dtc warnings

[ Upstream commit 7d79f6098d82f8c09914d7799bc96891ad9c3baf ]

dtc recently added PCI bus checks. Fix these warnings.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: VMX: Fix enable VPID conditions

[ Upstream commit 08d839c4b134b8328ec42f2157a9ca4b93227c03 ]

This can be reproduced by running L2 on L1, and disable VPID on L0
if w/o commit "KVM: nVMX: Fix nested VPID vmx exec control", the L2
crash as below:

KVM: entry failed, hardware error 0x7
EAX=00000000 EBX=00000000 ECX=00000000 EDX=000306c3
ESI=00000000 EDI=00000000 EBP=00000000 ESP=00000000
EIP=0000fff0 EFL=00000002 [-------] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =0000 00000000 0000ffff 00009300
CS =f000 ffff0000 0000ffff 00009b00
SS =0000 00000000 0000ffff 00009300
DS =0000 00000000 0000ffff 00009300
FS =0000 00000000 0000ffff 00009300
GS =0000 00000000 0000ffff 00009300
LDT=0000 00000000 0000ffff 00008200
TR =0000 00000000 0000ffff 00008b00
GDT=     00000000 0000ffff
IDT=     00000000 0000ffff
CR0=60000010 CR2=00000000 CR3=00000000 CR4=00000000
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000000

Reference SDM 30.3 INVVPID:

Protected Mode Exceptions
- #UD
  - If not in VMX operation.
  - If the logical processor does not support VPIDs (IA32_VMX_PROCBASED_CTLS2[37]=0).
  - If the logical processor supports VPIDs (IA32_VMX_PROCBASED_CTLS2[37]=1) but does
    not support the INVVPID instruction (IA32_VMX_EPT_VPID_CAP[32]=0).

So we should check both VPID enable bit in vmx exec control and INVVPID support bit
in vmx capability MSRs to enable VPID. This patch adds the guarantee to not enable
VPID if either INVVPID or single-context/all-context invalidation is not exposed in
vmx capability MSRs.

Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: correct async page present tracepoint

[ Upstream commit 24dccf83a121b8a4ad5c2ad383a8184ef6c266ee ]

After async pf setup successfully, there is a broadcast wakeup w/ special
token 0xffffffff which tells vCPU that it should wake up all processes
waiting for APFs though there is no real process waiting at the moment.

The async page present tracepoint print prematurely and fails to catch the
special token setup. This patch fixes it by moving the async page present
tracepoint after the special token setup.

Before patch:

qemu-system-x86-8499  [006] ...1  5973.473292: kvm_async_pf_ready: token 0x0 gva 0x0

After patch:

qemu-system-x86-8499  [006] ...1  5973.473292: kvm_async_pf_ready: token 0xffffffff gva 0x0

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: Fix PT2PT PRLI reject

[ Upstream commit a71e3cdcfce4880a4578915e110e3eaed1659765 ]

lpfc cannot establish connection with targets that send PRLI in P2P
configurations.

If lpfc rejects a PRLI that is sent from a target the target will not
resend and will reject the PRLI send from the initiator.

[mkp: applied by hand]

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: st: add irq_request/release_resources callbacks

[ Upstream commit e855fa9a65c40788b5069abb0d094537daa22e05 ]

When using GPIO as IRQ source, the GPIO must be configured
in INPUT. Callbacks dedicated for this was missing in
pinctrl-st driver.

This fix the following kernel error when trying to lock a gpio
as IRQ:

[    7.521095] gpio gpiochip7: (PIO11): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[    7.526018] gpio gpiochip7: (PIO11): unable to lock HW IRQ 6 for IRQ
[    7.529405] genirq: Failed to request resources for 0-0053 (irq 81) on irqchip GPIO

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

inet: frag: release spinlock before calling icmp_send()

[ Upstream commit ec4fbd64751de18729eaa816ec69e4b504b5a7a2 ]

Dmitry reported a lockdep splat [1] (false positive) that we can fix
by releasing the spinlock before calling icmp_send() from ip_expire()

This is a false positive because sending an ICMP message can not
possibly re-enter the IP frag engine.

[1]
[ INFO: possible circular locking dependency detected ]
4.10.0+ #29 Not tainted
-------------------------------------------------------
modprobe/12392 is trying to acquire lock:
 (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] spin_lock
include/linux/spinlock.h:299 [inline]
 (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] __netif_tx_lock
include/linux/netdevice.h:3486 [inline]
 (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>]
sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180

but task is already holding lock:
 (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock
include/linux/spinlock.h:299 [inline]
 (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>]
ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&(&q->lock)->rlock){+.-...}:
       validate_chain kernel/locking/lockdep.c:2267 [inline]
       __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340
       lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
       __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
       _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151
       spin_lock include/linux/spinlock.h:299 [inline]
       ip_defrag+0x3a2/0x4130 net/ipv4/ip_fragment.c:669
       ip_check_defrag+0x4e3/0x8b0 net/ipv4/ip_fragment.c:713
       packet_rcv_fanout+0x282/0x800 net/packet/af_packet.c:1459
       deliver_skb net/core/dev.c:1834 [inline]
       dev_queue_xmit_nit+0x294/0xa90 net/core/dev.c:1890
       xmit_one net/core/dev.c:2903 [inline]
       dev_hard_start_xmit+0x16b/0xab0 net/core/dev.c:2923
       sch_direct_xmit+0x31f/0x6d0 net/sched/sch_generic.c:182
       __dev_xmit_skb net/core/dev.c:3092 [inline]
       __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358
       dev_queue_xmit+0x17/0x20 net/core/dev.c:3423
       neigh_resolve_output+0x6b9/0xb10 net/core/neighbour.c:1308
       neigh_output include/net/neighbour.h:478 [inline]
       ip_finish_output2+0x8b8/0x15a0 net/ipv4/ip_output.c:228
       ip_do_fragment+0x1d93/0x2720 net/ipv4/ip_output.c:672
       ip_fragment.constprop.54+0x145/0x200 net/ipv4/ip_output.c:545
       ip_finish_output+0x82d/0xe10 net/ipv4/ip_output.c:314
       NF_HOOK_COND include/linux/netfilter.h:246 [inline]
       ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404
       dst_output include/net/dst.h:486 [inline]
       ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124
       ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492
       ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512
       raw_sendmsg+0x26de/0x3a00 net/ipv4/raw.c:655
       inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761
       sock_sendmsg_nosec net/socket.c:633 [inline]
       sock_sendmsg+0xca/0x110 net/socket.c:643
       ___sys_sendmsg+0x4a3/0x9f0 net/socket.c:1985
       __sys_sendmmsg+0x25c/0x750 net/socket.c:2075
       SYSC_sendmmsg net/socket.c:2106 [inline]
       SyS_sendmmsg+0x35/0x60 net/socket.c:2101
       do_syscall_64+0x2e8/0x930 arch/x86/entry/common.c:281
       return_from_SYSCALL_64+0x0/0x7a

-> #0 (_xmit_ETHER#2){+.-...}:
       check_prev_add kernel/locking/lockdep.c:1830 [inline]
       check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940
       validate_chain kernel/locking/lockdep.c:2267 [inline]
       __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340
       lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
       __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
       _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151
       spin_lock include/linux/spinlock.h:299 [inline]
       __netif_tx_lock include/linux/netdevice.h:3486 [inline]
       sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180
       __dev_xmit_skb net/core/dev.c:3092 [inline]
       __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358
       dev_queue_xmit+0x17/0x20 net/core/dev.c:3423
       neigh_hh_output include/net/neighbour.h:468 [inline]
       neigh_output include/net/neighbour.h:476 [inline]
       ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228
       ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316
       NF_HOOK_COND include/linux/netfilter.h:246 [inline]
       ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404
       dst_output include/net/dst.h:486 [inline]
       ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124
       ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492
       ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512
       icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394
       icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754
       ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239
       call_timer_fn+0x241/0x820 kernel/time/timer.c:1268
       expire_timers kernel/time/timer.c:1307 [inline]
       __run_timers+0x960/0xcf0 kernel/time/timer.c:1601
       run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614
       __do_softirq+0x31f/0xbe7 kernel/softirq.c:284
       invoke_softirq kernel/softirq.c:364 [inline]
       irq_exit+0x1cc/0x200 kernel/softirq.c:405
       exiting_irq arch/x86/include/asm/apic.h:657 [inline]
       smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962
       apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707
       __read_once_size include/linux/compiler.h:254 [inline]
       atomic_read arch/x86/include/asm/atomic.h:26 [inline]
       rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline]
       __rcu_is_watching kernel/rcu/tree.c:1133 [inline]
       rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147
       rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293
       radix_tree_deref_slot include/linux/radix-tree.h:238 [inline]
       filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335
       do_fault_around mm/memory.c:3231 [inline]
       do_read_fault mm/memory.c:3265 [inline]
       do_fault+0xbd5/0x2080 mm/memory.c:3370
       handle_pte_fault mm/memory.c:3600 [inline]
       __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714
       handle_mm_fault+0x1e2/0x480 mm/memory.c:3751
       __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397
       do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460
       page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&(&q->lock)->rlock);
                               lock(_xmit_ETHER#2);
                               lock(&(&q->lock)->rlock);
  lock(_xmit_ETHER#2);

 *** DEADLOCK ***

10 locks held by modprobe/12392:
 #0:  (&mm->mmap_sem){++++++}, at: [<ffffffff81329758>]
__do_page_fault+0x2b8/0xb60 arch/x86/mm/fault.c:1336
 #1:  (rcu_read_lock){......}, at: [<ffffffff8188cab6>]
filemap_map_pages+0x1e6/0x1570 mm/filemap.c:2324
 #2:  (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>]
spin_lock include/linux/spinlock.h:299 [inline]
 #2:  (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>]
pte_alloc_one_map mm/memory.c:2944 [inline]
 #2:  (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>]
alloc_set_pte+0x13b8/0x1b90 mm/memory.c:3072
 #3:  (((&q->timer))){+.-...}, at: [<ffffffff81627e72>]
lockdep_copy_map include/linux/lockdep.h:175 [inline]
 #3:  (((&q->timer))){+.-...}, at: [<ffffffff81627e72>]
call_timer_fn+0x1c2/0x820 kernel/time/timer.c:1258
 #4:  (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock
include/linux/spinlock.h:299 [inline]
 #4:  (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>]
ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201
 #5:  (rcu_read_lock){......}, at: [<ffffffff8389a633>]
ip_expire+0x1b3/0x6c0 net/ipv4/ip_fragment.c:216
 #6:  (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] spin_trylock
include/linux/spinlock.h:309 [inline]
 #6:  (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_xmit_lock
net/ipv4/icmp.c:219 [inline]
 #6:  (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>]
icmp_send+0x803/0x1c80 net/ipv4/icmp.c:681
 #7:  (rcu_read_lock_bh){......}, at: [<ffffffff838ab9a1>]
ip_finish_output2+0x2c1/0x15a0 net/ipv4/ip_output.c:198
 #8:  (rcu_read_lock_bh){......}, at: [<ffffffff836d1dee>]
__dev_queue_xmit+0x23e/0x1e60 net/core/dev.c:3324
 #9:  (dev->qdisc_running_key ?: &qdisc_running_key){+.....}, at:
[<ffffffff836d3a27>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3423

stack backtrace:
CPU: 0 PID: 12392 Comm: modprobe Not tainted 4.10.0+ #29
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 01/01/2011
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x2ee/0x3ef lib/dump_stack.c:52
 print_circular_bug+0x307/0x3b0 kernel/locking/lockdep.c:1204
 check_prev_add kernel/locking/lockdep.c:1830 [inline]
 check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940
 validate_chain kernel/locking/lockdep.c:2267 [inline]
 __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340
 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
 _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151
 spin_lock include/linux/spinlock.h:299 [inline]
 __netif_tx_lock include/linux/netdevice.h:3486 [inline]
 sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180
 __dev_xmit_skb net/core/dev.c:3092 [inline]
 __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358
 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423
 neigh_hh_output include/net/neighbour.h:468 [inline]
 neigh_output include/net/neighbour.h:476 [inline]
 ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228
 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316
 NF_HOOK_COND include/linux/netfilter.h:246 [inline]
 ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404
 dst_output include/net/dst.h:486 [inline]
 ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124
 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492
 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512
 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394
 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754
 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239
 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268
 expire_timers kernel/time/timer.c:1307 [inline]
 __run_timers+0x960/0xcf0 kernel/time/timer.c:1601
 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614
 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284
 invoke_softirq kernel/softirq.c:364 [inline]
 irq_exit+0x1cc/0x200 kernel/softirq.c:405
 exiting_irq arch/x86/include/asm/apic.h:657 [inline]
 smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962
 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707
RIP: 0010:__read_once_size include/linux/compiler.h:254 [inline]
RIP: 0010:atomic_read arch/x86/include/asm/atomic.h:26 [inline]
RIP: 0010:rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline]
RIP: 0010:__rcu_is_watching kernel/rcu/tree.c:1133 [inline]
RIP: 0010:rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147
RSP: 0000:ffff8801c391f120 EFLAGS: 00000a03 ORIG_RAX: ffffffffffffff10
RAX: dffffc0000000000 RBX: ffff8801c391f148 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 000055edd4374000 RDI: ffff8801dbe1ae0c
RBP: ffff8801c391f1a0 R08: 0000000000000002 R09: 0000000000000000
R10: dffffc0000000000 R11: 0000000000000002 R12: 1ffff10038723e25
R13: ffff8801dbe1ae00 R14: ffff8801c391f680 R15: dffffc0000000000
 </IRQ>
 rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293
 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline]
 filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335
 do_fault_around mm/memory.c:3231 [inline]
 do_read_fault mm/memory.c:3265 [inline]
 do_fault+0xbd5/0x2080 mm/memory.c:3370
 handle_pte_fault mm/memory.c:3600 [inline]
 __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714
 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751
 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397
 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460
 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011
RIP: 0033:0x7f83172f2786
RSP: 002b:00007fffe859ae80 EFLAGS: 00010293
RAX: 000055edd4373040 RBX: 00007f83175111c8 RCX: 000055edd4373238
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007f8317510970
RBP: 00007fffe859afd0 R08: 0000000000000009 R09: 0000000000000000
R10: 0000000000000064 R11: 0000000000000000 R12: 000055edd4373040
R13: 0000000000000000 R14: 00007fffe859afe8 R15: 0000000000000000

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nfnl_cthelper: Fix memory leak

[ Upstream commit f83bf8da1135ca635aac8f062cad3f001fcf3a26 ]

We have memory leaks of nf_conntrack_helper & expect_policy.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nfnl_cthelper: fix runtime expectation policy updates

[ Upstream commit 2c422257550f123049552b39f7af6e3428a60f43 ]

We only allow runtime updates of expectation policies for timeout and
maximum number of expectations, otherwise reject the update.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: udc: remove pointer dereference after free

[ Upstream commit 1f459262b0e1649a1e5ad12fa4c66eb76c2220ce ]

Remove pointer dereference after free.

Addresses-Coverity-ID: 1091173
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeed

[ Upstream commit 16bb05d98c904a4f6c5ce7e2d992299f794acbf2 ]

As per USB3.0 Specification "Table 9-20. Standard Endpoint Descriptor",
for interrupt and isochronous endpoints, wMaxPacketSize must be set to
1024 if the endpoint defines bMaxBurst to be greater than zero.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: Add USB IDs for MDM6600 modem on Motorola Droid 4

[ Upstream commit 4071898bf0f4d79ff353db327af2a15123272548 ]

This gets qmicli working with the MDM6600 modem.

Cc: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bna: integer overflow bug in debugfs

[ Upstream commit 13e2d5187f6b965ba3556caedb914baf81b98ed2 ]

We could allocate less memory than intended because we do:

bnad->regdata = kzalloc(len << 2, GFP_KERNEL);

The shift can overflow leading to a crash.  This is debugfs code so the
impact is very small.

Fixes: 7afc5dbde091 ("bna: Add debugfs interface.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sch_dsmark: fix invalid skb_cow() usage

[ Upstream commit aea92fb2e09e29653b023d4254ac9fbf94221538 ]

skb_cow(skb, sizeof(ip header)) is not very helpful in this context.

First we need to use pskb_may_pull() to make sure the ip header
is in skb linear part, then use skb_try_make_writable() to
address clones issues.

Fixes: 4c30719f4f55 ("[PKT_SCHED] dsmark: handle cloned and non-linear skb's")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: deadlock between crypto_alg_sem/rtnl_mutex/genl_mutex

[ Upstream commit 8a0f5ccfb33b0b8b51de65b7b3bf342ba10b4fb6 ]

On Tue, Mar 14, 2017 at 10:44:10AM +0100, Dmitry Vyukov wrote:
>
> Yes, please.
> Disregarding some reports is not a good way long term.

Please try this patch.

---8<---
Subject: netlink: Annotate nlk cb_mutex by protocol

Currently all occurences of nlk->cb_mutex are annotated by lockdep
as a single class.  This causes a false lcokdep cycle involving
genl and crypto_user.

This patch fixes it by dividing cb_mutex into individual classes
based on the netlink protocol.  As genl and crypto_user do not
use the same netlink protocol this breaks the false dependency
loop.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

r8152: fix the list rx_done may be used without initialization

[ Upstream commit 98d068ab52b4b11d403995ed14154660797e7136 ]

The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.

BUG: unable to handle kernel NULL pointer dereference at 000000000000008
IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
PGD 0
Oops: 0002 [#1] SMP

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpuidle: Validate cpu_dev in cpuidle_add_sysfs()

[ Upstream commit ad0a45fd9c14feebd000b6e84189d0edff265170 ]

If a given cpu is not in cpu_present and cpu hotplug
is disabled, arch can skip setting up the cpu_dev.

Arch cpuidle driver should pass correct cpu mask
for registration, but failing to do so by the driver
causes error to propagate and crash like this:

[   30.076045] Unable to handle kernel paging request for data at address 0x00000048
[   30.076100] Faulting instruction address: 0xc0000000007b2f30
cpu 0x4d: Vector: 300 (Data Access) at [c000003feb18b670]
    pc: c0000000007b2f30: kobject_get+0x20/0x70
    lr: c0000000007b3c94: kobject_add_internal+0x54/0x3f0
    sp: c000003feb18b8f0
   msr: 9000000000009033
   dar: 48
 dsisr: 40000000
  current = 0xc000003fd2ed8300
  paca    = 0xc00000000fbab500   softe: 0        irq_happened: 0x01
    pid   = 1, comm = swapper/0
Linux version 4.11.0-rc2-svaidy+ (sv@sagarika) (gcc version 6.2.0
20161005 (Ubuntu 6.2.0-5ubuntu12) ) #10 SMP Sun Mar 19 00:08:09 IST 2017
enter ? for help
[c000003feb18b960] c0000000007b3c94 kobject_add_internal+0x54/0x3f0
[c000003feb18b9f0] c0000000007b43a4 kobject_init_and_add+0x64/0xa0
[c000003feb18ba70] c000000000e284f4 cpuidle_add_sysfs+0xb4/0x130
[c000003feb18baf0] c000000000e26038 cpuidle_register_device+0x118/0x1c0
[c000003feb18bb30] c000000000e26c48 cpuidle_register+0x78/0x120
[c000003feb18bbc0] c00000000168fd9c powernv_processor_idle_init+0x110/0x1c4
[c000003feb18bc40] c00000000000cff8 do_one_initcall+0x68/0x1d0
[c000003feb18bd00] c0000000016242f4 kernel_init_freeable+0x280/0x360
[c000003feb18bdc0] c00000000000d864 kernel_init+0x24/0x160
[c000003feb18be30] c00000000000b4e8 ret_from_kernel_thread+0x5c/0x74

Validating cpu_dev fixes the crash and reports correct error message like:

[   30.163506] Failed to register cpuidle device for cpu136
[   30.173329] Registration of powernv driver failed.

Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[ rjw: Comment massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm: kprobes: Align stack to 8-bytes in test code

[ Upstream commit 974310d047f3c7788a51d10c8d255eebdb1fa857 ]

kprobes test cases need to have a stack that is aligned to an 8-byte
boundary because they call other functions (and the ARM ABI mandates
that alignment) and because test cases include 64-bit accesses to the
stack. Unfortunately, GCC doesn't ensure this alignment for inline
assembler and for the code in question seems to always misalign it by
pushing just the LR register onto the stack. We therefore need to
explicitly perform stack alignment at the start of each test case.

Without this fix, some test cases will generate alignment faults on
systems where alignment is enforced. Even if the kernel is configured to
handle these faults in software, triggering them is ugly. It also
exposes limitations in the fault handling code which doesn't cope with
writes to the stack. E.g. when handling this instruction

   strd r6, [sp, #-64]!

the fault handling code will write to a stack location below the SP
value at the point the fault occurred, which coincides with where the
exception handler has pushed the saved register context. This results in
corruption of those registers.

Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm: kprobes: Fix the return address of multiple kretprobes

[ Upstream commit 06553175f585b52509c7df37d6f4a50aacb7b211 ]

This is arm port of commit 737480a0d525 ("kprobes/x86:
Fix the return address of multiple kretprobes").

Fix the return address of subsequent kretprobes when multiple
kretprobes are set on the same function.

For example:

  # cd /sys/kernel/debug/tracing
  # echo "r:event1 sys_symlink" > kprobe_events
  # echo "r:event2 sys_symlink" >> kprobe_events
  # echo 1 > events/kprobes/enable
  # ln -s /tmp/foo /tmp/bar

 (without this patch)

  # cat trace | grep -v ^#
              ln-82    [000] dn.2    68.446525: event1: (kretprobe_trampoline+0x0/0x18 <- SyS_symlink)
              ln-82    [000] dn.2    68.447831: event2: (ret_fast_syscall+0x0/0x1c <- SyS_symlink)

 (with this patch)

  # cat trace | grep -v ^#
              ln-81    [000] dn.1    39.463469: event1: (ret_fast_syscall+0x0/0x1c <- SyS_symlink)
              ln-81    [000] dn.1    39.464701: event2: (ret_fast_syscall+0x0/0x1c <- SyS_symlink)

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: KUMANO Syuhei <kumano.prog@gmail.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - add support for docking station for HP 840 G3

[ Upstream commit cc3a47a248d7791ef0d2c81a35c46769e55e4c6c ]

This tested patch adds missing initialization for Line-In/Out PINs for
the docking station for HP 840 G3.

Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - add support for docking station for HP 820 G2

[ Upstream commit 04d5466a976b096364a39a63ac264c1b3a5f8fa1 ]

This tested patch adds missing initialization for Line-In/Out PINs for
the docking station for HP 820 G2.

Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/irq: Do not substract irq_tlb_count from irq_call_count

commit 82ba4faca1bffad429f15c90c980ffd010366c25 upstream.

Since commit:

  52aec3308db8 ("x86/tlb: replace INVALIDATE_TLB_VECTOR by CALL_FUNCTION_VECTOR")

the TLB remote shootdown is done through call function vector. That
commit didn't take care of irq_tlb_count, which a later commit:

  fd0f5869724f ("x86: Distinguish TLB shootdown interrupts from other functions call interrupts")

... tried to fix.

The fix assumes every increase of irq_tlb_count has a corresponding
increase of irq_call_count. So the irq_call_count is always bigger than
irq_tlb_count and we could substract irq_tlb_count from irq_call_count.

Unfortunately this is not true for the smp_call_function_single() case.
The IPI is only sent if the target CPU's call_single_queue is empty when
adding a csd into it in generic_exec_single. That means if two threads
are both adding flush tlb csds to the same CPU's call_single_queue, only
one IPI is sent. In other words, the irq_call_count is incremented by 1
but irq_tlb_count is incremented by 2. Over time, irq_tlb_count will be
bigger than irq_call_count and the substract will produce a very large
irq_call_count value due to overflow.

Considering that:

  1) it's not worth to send more IPIs for the sake of accurate counting of
     irq_call_count in generic_exec_single();

  2) it's not easy to tell if the call function interrupt is for TLB
     shootdown in __smp_call_function_single_interrupt().

Not to exclude TLB shootdown from call function count seems to be the
simplest fix and this patch just does that.

This bug was found by LKP's cyclic performance regression tracking recently
with the vm-scalability test suite. I have bisected to commit:

  3dec0ba0be6a ("mm/rmap: share the i_mmap_rwsem")

This commit didn't do anything wrong but revealed the irq_call_count
problem. IIUC, the commit makes rwc->remap_one in rmap_walk_file
concurrent with multiple threads.  When remap_one is try_to_unmap_one(),
then multiple threads could queue flush TLB to the same CPU but only
one IPI will be sent.

Since the commit was added in Linux v3.19, the counting problem only
shows up from v3.19 onwards.

Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Link: http://lkml.kernel.org/r/20160811074430.GA18163@aaronlu.sh.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/core: Idle_task_exit() shouldn't use switch_mm_irqs_off()

commit 252d2a4117bc181b287eeddf848863788da733ae upstream.

idle_task_exit() can be called with IRQs on x86 on and therefore
should use switch_mm(), not switch_mm_irqs_off().

This doesn't seem to cause any problems right now, but it will
confuse my upcoming TLB flush changes.  Nonetheless, I think it
should be backported because it's trivial.  There won't be any
meaningful performance impact because idle_task_exit() is only
used when offlining a CPU.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: f98db6013c55 ("sched/core: Add switch_mm_irqs_off() and use it in the scheduler")
Link: http://lkml.kernel.org/r/ca3d1a9fa93a0b49f5a8ff729eda3640fb6abdf9.1497034141.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: Hide finish_arch_post_lock_switch() from modules

commit ef0491ea17f8019821c7e9c8e801184ecf17f85a upstream.

The introduction of switch_mm_irqs_off() brought back an old bug
regarding the use of preempt_enable_no_resched:

As part of:

  62b94a08da1b ("sched/preempt: Take away preempt_enable_no_resched() from modules")

the definition of preempt_enable_no_resched() is only available in
built-in code, not in loadable modules, so we can't generally use
it from header files.

However, the ARM version of finish_arch_post_lock_switch()
calls preempt_enable_no_resched() and is defined as a static
inline function in asm/mmu_context.h. This in turn means we cannot
include asm/mmu_context.h from modules.

With today's tip tree, asm/mmu_context.h gets included from
linux/mmu_context.h, which is normally the exact pattern one would
expect, but unfortunately, linux/mmu_context.h can be included from
the vhost driver that is a loadable module, now causing this compile
time error with modular configs:

  In file included from ../include/linux/mmu_context.h:4:0,
                   from ../drivers/vhost/vhost.c:18:
  ../arch/arm/include/asm/mmu_context.h: In function 'finish_arch_post_lock_switch':
  ../arch/arm/include/asm/mmu_context.h:88:3: error: implicit declaration of function 'preempt_enable_no_resched' [-Werror=implicit-function-declaration]
     preempt_enable_no_resched();

Andy already tried to fix the bug by including linux/preempt.h
from asm/mmu_context.h, but that didn't help. Arnd suggested reordering
the header files, which wasn't popular, so let's use this
workaround instead:

The finish_arch_post_lock_switch() definition is now also hidden
inside of #ifdef MODULE, so we don't see anything referencing
preempt_enable_no_resched() from a header file. I've built a
few hundred randconfig kernels with this, and did not see any
new problems.

Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: f98db6013c55 ("sched/core: Add switch_mm_irqs_off() and use it in the scheduler")
Link: http://lkml.kernel.org/r/1463146234-161304-1-git-send-email-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm, sched/core: Turn off IRQs in switch_mm()

commit 078194f8e9fe3cf54c8fd8bded48a1db5bd8eb8a upstream.

Potential races between switch_mm() and TLB-flush or LDT-flush IPIs
could be very messy.  AFAICT the code is currently okay, whether by
accident or by careful design, but enabling PCID will make it
considerably more complicated and will no longer be obviously safe.

Fix it with a big hammer: run switch_mm() with IRQs off.

To avoid a performance hit in the scheduler, we take advantage of
our knowledge that the scheduler already has IRQs disabled when it
calls switch_mm().

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f19baf759693c9dcae64bbff76189db77cb13398.1461688545.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm, sched/core: Uninline switch_mm()

commit 69c0319aabba45bcf33178916a2f06967b4adede upstream.

It's fairly large and it has quite a few callers.  This may also
help untangle some headers down the road.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/54f3367803e7f80b2be62c8a21879aa74b1a5f57.1461688545.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm: Build arch/x86/mm/tlb.c even on !SMP

commit e1074888c326038340a1ada9129d679e661f2ea6 upstream.

Currently all of the functions that live in tlb.c are inlined on
!SMP builds.  One can debate whether this is a good idea (in many
respects the code in tlb.c is better than the inlined UP code).

Regardless, I want to add code that needs to be built on UP and SMP
kernels and relates to tlb flushing, so arrange for tlb.c to be
compiled unconditionally.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f0d778f0d828fc46e5d1946bca80f0aaf9abf032.1461688545.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/core: Add switch_mm_irqs_off() and use it in the scheduler

commit f98db6013c557c216da5038d9c52045be55cd039 upstream.

By default, this is the same thing as switch_mm().

x86 will override it as an optimization.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/df401df47bdd6be3e389c6f1e3f5310d70e81b2c.1461688545.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/mmu_context, sched/core: Fix mmu_context.h assumption

commit 8efd755ac2fe262d4c8d5c9bbe054bb67dae93da upstream.

Some architectures (such as Alpha) rely on include/linux/sched.h definitions
in their mmu_context.h files.

So include sched.h before mmu_context.h.

Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/rmap: batched invalidations should use existing api

commit 858eaaa711700ce4595e039441e239e56d7b9514 upstream.

The recently introduced batched invalidations mechanism uses its own
mechanism for shootdown.  However, it does wrong accounting of
interrupts (e.g., inc_irq_stat is called for local invalidations),
trace-points (e.g., TLB_REMOTE_SHOOTDOWN for local invalidations) and
may break some platforms as it bypasses the invalidation mechanisms of
Xen and SGI UV.

This patch reuses the existing TLB flushing mechnaisms instead.  We use
NULL as mm to indicate a global invalidation is required.

Fixes 72b252aed506b8 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm: If INVPCID is available, use it to flush global mappings

commit d8bced79af1db6734f66b42064cc773cada2ce99 upstream.

On my Skylake laptop, INVPCID function 2 (flush absolutely
everything) takes about 376ns, whereas saving flags, twiddling
CR4.PGE to flush global mappings, and restoring flags takes about
539ns.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/ed0ef62581c0ea9c99b9bf6df726015e96d44743.1454096309.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm: Add a 'noinvpcid' boot option to turn off INVPCID

commit d12a72b844a49d4162f24cefdab30bed3f86730e upstream.

This adds a chicken bit to turn off INVPCID in case something goes
wrong.  It's an early_param() because we do TLB flushes before we
parse __setup() parameters.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/f586317ed1bc2b87aee652267e515b90051af385.1454096309.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm: Fix INVPCID asm constraint

commit e2c7698cd61f11d4077fdb28148b2d31b82ac848 upstream.

So we want to specify the dependency on both @pcid and @addr so that the
compiler doesn't reorder accesses to them *before* the TLB flush. But
for that to work, we need to express this properly in the inline asm and
deref the whole desc array, not the pointer to it. See clwb() for an
example.

This fixes the build error on 32-bit:

  arch/x86/include/asm/tlbflush.h: In function ‘__invpcid’:
  arch/x86/include/asm/tlbflush.h:26:18: error: memory input 0 is not directly addressable

which gcc4.7 caught but 5.x didn't. Which is strange. :-\

Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Michael Matz <matz@suse.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: linux-mm@kvack.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm: Add INVPCID helpers

commit 060a402a1ddb551455ee410de2eadd3349f2801b upstream.

This adds helpers for each of the four currently-specified INVPCID
modes.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/8a62b23ad686888cee01da134c91409e22064db9.1454096309.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxl: Check if vphb exists before iterating over AFU devices

commit 12841f87b7a8ceb3d54f171660f72a86941bfcb3 upstream.

During an eeh a kernel-oops is reported if no vPHB is allocated to the
AFU. This happens as during AFU init, an error in creation of vPHB is
a non-fatal error. Hence afu->phb should always be checked for NULL
before iterating over it for the virtual AFU pci devices.

This patch fixes the kenel-oops by adding a NULL pointer check for
afu->phb before it is dereferenced.

Fixes: 9e8df8a21963 ("cxl: EEH support")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Initialise high_memory global variable earlier

commit f24e5834a2c3f6c5f814a417f858226f0a010ade upstream.

The high_memory global variable is used by
cma_declare_contiguous(.) before it is defined.

We don't notice this as we compute __pa(high_memory - 1), and it looks
like we're processing a VA from the direct linear map.

This problem becomes apparent when we flip the kernel virtual address
space and the linear map is moved to the bottom of the kernel VA space.

This patch moves the initialisation of high_memory before it used.

Fixes: f7426b983a6a ("mm: cma: adjust address limit to avoid hitting low/high memory boundary")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.107

ath9k: fix tx99 potential info leak

[ Upstream commit ee0a47186e2fa9aa1c56cadcea470ca0ba8c8692 ]

When the user sets count to zero the string buffer would remain
completely uninitialized which causes the kernel to parse its
own stack data, potentially leading to an info leak. In addition
to that, the string might be not terminated properly when the
user data does not contain a 0-terminator.

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/ipoib: Grab rtnl lock on heavy flush when calling ndo_open/stop

[ Upstream commit b4b678b06f6eef18bff44a338c01870234db0bc9 ]

When ndo_open and ndo_stop are called RTNL lock should be held.
In this specific case ipoib_ib_dev_open calls the offloaded ndo_open
which re-sets the number of TX queue assuming RTNL lock is held.
Since RTNL lock is not held, RTNL assert will fail.

Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/cma: Avoid triggering undefined behavior

[ Upstream commit c0b64f58e8d49570aa9ee55d880f92c20ff0166b ]

According to the C standard the behavior of computations with
integer operands is as follows:
* A computation involving unsigned operands can never overflow,
  because a result that cannot be represented by the resulting
  unsigned integer type is reduced modulo the number that is one
  greater than the largest value that can be represented by the
  resulting type.
* The behavior for signed integer underflow and overflow is
  undefined.

Hence only use unsigned integers when checking for integer
overflow.

This patch is what I came up with after having analyzed the
following smatch warnings:

drivers/infiniband/core/cma.c:3448: cma_resolve_ib_udp() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'
drivers/infiniband/core/cma.c:3505: cma_connect_ib() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'

Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

macvlan: Only deliver one copy of the frame to the macvlan interface

[ Upstream commit dd6b9c2c332b40f142740d1b11fb77c653ff98ea ]

This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.

The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.

Fixes: 79cf79abce71 ("macvlan: add source mode")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udf: Avoid overflow when session starts at large offset

[ Upstream commit abdc0eb06964fe1d2fea6dd1391b734d0590365d ]

When session starts beyond offset 2^31 the arithmetics in
udf_check_vsd() would overflow. Make sure the computation is done in
large enough type.

Reported-by: Cezary Sliwa <sliwa@ifpan.edu.pl>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: bfa: integer overflow in debugfs

[ Upstream commit 3e351275655d3c84dc28abf170def9786db5176d ]

We could allocate less memory than intended because we do:

bfad->regdata = kzalloc(len << 2, GFP_KERNEL);

The shift can overflow leading to a crash.  This is debugfs code so the
impact is very small.  I fixed the network version of this in March with
commit 13e2d5187f6b ("bna: integer overflow bug in debugfs").

Fixes: ab2a9ba189e8 ("[SCSI] bfa: add debugfs support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sd: change allow_restart to bool in sysfs interface

[ Upstream commit 658e9a6dc1126f21fa417cd213e1cdbff8be0ba2 ]

/sys/class/scsi_disk/0:2:0:0/allow_restart can be changed to 0
unexpectedly by writing an invalid string such as the following:

echo asdf > /sys/class/scsi_disk/0:2:0:0/allow_restart

Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sd: change manage_start_stop to bool in sysfs interface

[ Upstream commit 623401ee33e42cee64d333877892be8db02951eb ]

/sys/class/scsi_disk/0:2:0:0/manage_start_stop can be changed to 0
unexpectly by writing an invalid string.

Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt6655: Fix a possible sleep-in-atomic bug in vt6655_suspend

[ Upstream commit 42c8eb3f6e15367981b274cb79ee4657e2c6949d ]

The driver may sleep under a spinlock, and the function call path is:
vt6655_suspend (acquire the spinlock)
  pci_set_power_state
    __pci_start_power_transition (drivers/pci/pci.c)
      msleep --> may sleep

To fix it, pci_set_power_state is called without having a spinlock.

This bug is found by my static analysis tool and my code review.

Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: scsi_devinfo: Add REPORTLUN2 to EMC SYMMETRIX blacklist entry

[ Upstream commit 909cf3e16a5274fe2127cf3cea5c8dba77b2c412 ]

All EMC SYMMETRIX support REPORT_LUNS, even if configured to report
SCSI-2 for whatever reason.

Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

raid5: Set R5_Expanded on parity devices as well as data.

[ Upstream commit 235b6003fb28f0dd8e7ed8fbdb088bb548291766 ]

When reshaping a fully degraded raid5/raid6 to a larger
nubmer of devices, the new device(s) are not in-sync
and so that can make the newly grown stripe appear to be
"failed".
To avoid this, we set the R5_Expanded flag to say "Even though
this device is not fully in-sync, this block is safe so
don't treat the device as failed for this stripe".
This flag is set for data devices, not not for parity devices.

Consequently, if you have a RAID6 with two devices that are partly
recovered and a spare, and start a reshape to include the spare,
then when the reshape gets past the point where the recovery was
up to, it will think the stripes are failed and will get into
an infinite loop, failing to make progress.

So when contructing parity on an EXPAND_READY stripe,
set R5_Expanded.

Reported-by: Curt <lightspd@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: adi2: Fix Kconfig build problem

[ Upstream commit 1c363531dd814dc4fe10865722bf6b0f72ce4673 ]

The build robot is complaining on Blackfin:

drivers/pinctrl/pinctrl-adi2.c: In function 'port_setup':
>> drivers/pinctrl/pinctrl-adi2.c:221:21: error: dereferencing
   pointer to incomplete type 'struct gpio_port_t'
      writew(readw(&regs->port_fer) & ~BIT(offset),
                        ^~
drivers/pinctrl/pinctrl-adi2.c: In function 'adi_gpio_ack_irq':
>> drivers/pinctrl/pinctrl-adi2.c:266:18: error: dereferencing
pointer to incomplete type 'struct bfin_pint_regs'
      if (readl(&regs->invert_set) & pintbit)
                     ^~
It seems the driver need to include <asm/gpio.h> and <asm/irq.h>
to compile.

The Blackfin architecture was re-defining the Kconfig
PINCTRL symbol which is not OK, so replaced this with
PINCTRL_BLACKFIN_ADI2 which selects PINCTRL and PINCTRL_ADI2
just like most arches do.

Further, the old GPIO driver symbol GPIO_ADI was possible to
select at the same time as selecting PINCTRL. This was not
working because the arch-local <asm/gpio.h> header contains
an explicit #ifndef PINCTRL clause making compilation break
if you combine them. The same is true for DEBUG_MMRS.

Make sure the ADI2 pinctrl driver is not selected at the same
time as the old GPIO implementation. (This should be converted
to use gpiolib or pincontrol and move to drivers/...) Also make
sure the old GPIO_ADI driver or DEBUG_MMRS is not selected at
the same time as the new PINCTRL implementation, and only make
PINCTRL_ADI2 selectable for the Blackfin families that actually
have it.

This way it is still possible to add e.g. I2C-based pin
control expanders on the Blackfin.

Cc: Steven Miao <realmz6@gmail.com>
Cc: Huanhuan Feng <huanhuan.feng@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: da8xx: fix babble condition handling

commit bd3486ded7a0c313a6575343e6c2b21d14476645 upstream.

When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.

In this case, we should handle the babble interrupt first and recover
from the babble condition.

This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.

Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty fix oops when rmmod 8250

[ Upstream commit c79dde629d2027ca80329c62854a7635e623d527 ]

After rmmod 8250.ko
tty_kref_put starts kwork (release_one_tty) to release proc interface
oops when accessing driver->driver_name in proc_tty_unregister_driver

Use jprobe, found driver->driver_name point to 8250.ko
static static struct uart_driver serial8250_reg
.driver_name= serial,

Use name in proc_dir_entry instead of driver->driver_name to fix oops

test on linux 4.1.12:

BUG: unable to handle kernel paging request at ffffffffa01979de
IP: [<ffffffff81310f40>] strchr+0x0/0x30
PGD 1a0d067 PUD 1a0e063 PMD 851c1f067 PTE 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ... ...  [last unloaded: 8250]
CPU: 7 PID: 116 Comm: kworker/7:1 Tainted: G           O    4.1.12 #1
Hardware name: Insyde RiverForest/Type2 - Board Product Name1, BIOS NE5KV904 12/21/2015
Workqueue: events release_one_tty
task: ffff88085b684960 ti: ffff880852884000 task.ti: ffff880852884000
RIP: 0010:[<ffffffff81310f40>]  [<ffffffff81310f40>] strchr+0x0/0x30
RSP: 0018:ffff880852887c90  EFLAGS: 00010282
RAX: ffffffff81a5eca0 RBX: ffffffffa01979de RCX: 0000000000000004
RDX: ffff880852887d10 RSI: 000000000000002f RDI: ffffffffa01979de
RBP: ffff880852887cd8 R08: 0000000000000000 R09: ffff88085f5d94d0
R10: 0000000000000195 R11: 0000000000000000 R12: ffffffffa01979de
R13: ffff880852887d00 R14: ffffffffa01979de R15: ffff88085f02e840
FS:  0000000000000000(0000) GS:ffff88085f5c0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa01979de CR3: 0000000001a0c000 CR4: 00000000001406e0
Stack:
 ffffffff812349b1 ffff880852887cb8 ffff880852887d10 ffff88085f5cd6c2
 ffff880852800a80 ffffffffa01979de ffff880852800a84 0000000000000010
 ffff88085bb28bd8 ffff880852887d38 ffffffff812354f0 ffff880852887d08
Call Trace:
 [<ffffffff812349b1>] ? __xlate_proc_name+0x71/0xd0
 [<ffffffff812354f0>] remove_proc_entry+0x40/0x180
 [<ffffffff815f6811>] ? _raw_spin_lock_irqsave+0x41/0x60
 [<ffffffff813be520>] ? destruct_tty_driver+0x60/0xe0
 [<ffffffff81237c68>] proc_tty_unregister_driver+0x28/0x40
 [<ffffffff813be548>] destruct_tty_driver+0x88/0xe0
 [<ffffffff813be5bd>] tty_driver_kref_put+0x1d/0x20
 [<ffffffff813becca>] release_one_tty+0x5a/0xd0
 [<ffffffff81074159>] process_one_work+0x139/0x420
 [<ffffffff810745a1>] worker_thread+0x121/0x450
 [<ffffffff81074480>] ? process_scheduled_works+0x40/0x40
 [<ffffffff8107a16c>] kthread+0xec/0x110
 [<ffffffff81080000>] ? tg_rt_schedulable+0x210/0x220
 [<ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80
 [<ffffffff815f7292>] ret_from_fork+0x42/0x70
 [<ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80

Signed-off-by: nixiaoming <nixiaoming@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/perf/hv-24x7: Fix incorrect comparison in memord

[ Upstream commit 05c14c03138532a3cb2aa29c2960445c8753343b ]

In the hv-24x7 code there is a function memord() which tries to
implement a sort function return -1, 0, 1. However one of the
conditions is incorrect, such that it can never be true, because we
will have already returned.

I don't believe there is a bug in practice though, because the
comparisons are an optimisation prior to calling memcmp().

Fix it by swapping the second comparision, so it can be true.

Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: hpsa: destroy sas transport properties before scsi_host

[ Upstream commit dfb2e6f46b3074eb85203d8f0888b71ec1c2e37a ]

This patch cleans up a lot of warnings when unloading the driver.

A current example of the stack trace starts with:
    [  142.570715] sysfs group 'power' not found for kobject 'port-5:0'
There can be hundreds of these messages during a driver unload.

I am resubmitting this patch on behalf of Martin Wilck with his
permission.

His original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102085.html

This patch did not help until Hannes's
commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.

---------------------------
Original patch description:
---------------------------

Unloading the hpsa driver causes warnings

[ 1063.793652] WARNING: CPU: 1 PID: 4850 at ../fs/sysfs/group.c:237 device_del+0x54/0x240()
[ 1063.793659] sysfs group ffffffff81cf21a0 not found for kobject 'port-2:0'

with two different stacks:
1)
[ 1063.793774]  [<ffffffff81448af4>] device_del+0x54/0x240
[ 1063.793780]  [<ffffffff8145178a>] transport_remove_classdev+0x4a/0x60
[ 1063.793784]  [<ffffffff81451216>] attribute_container_device_trigger+0xa6/0xb0
[ 1063.793802]  [<ffffffffa0105d46>] sas_port_delete+0x126/0x160 [scsi_transport_sas]
[ 1063.793819]  [<ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa]

2)
[ 1063.797103]  [<ffffffff81448af4>] device_del+0x54/0x240
[ 1063.797118]  [<ffffffffa0105d4e>] sas_port_delete+0x12e/0x160 [scsi_transport_sas]
[ 1063.797134]  [<ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa]

This is caused by the fact that host device hostX is deleted before the
SAS transport devices hostX/port-a:b.

This patch fixes this by reverting the order of device deletions.

Tested-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin Wilck <mwilck@suse.de>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: hpsa: cleanup sas_phy structures in sysfs when unloading

[ Upstream commit 55ca38b4255bb336c2d35990bdb2b368e19b435a ]

I am resubmitting this patch on behalf of Martin Wilck with his
permission.

The original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102083.html

This patch did not help until Hannes's
commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.

--------------------------------------
Original patch description from Martin:
--------------------------------------

When the hpsa module is unloaded using rmmod, dangling
symlinks remain under /sys/class/sas_phy. Fix this by
calling sas_phy_delete() rather than sas_phy_free (which,
according to comments, should not be called for PHYs that
have been set up successfully, anyway).

Tested-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin Wilck <mwilck@suse.de>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Detach driver before procfs & sysfs teardown on device remove

[ Upstream commit 16b6c8bb687cc3bec914de09061fcb8411951fda ]

When removing a device, for example a VF being removed due to SR-IOV
teardown, a "soft" hot-unplug via 'echo 1 > remove' in sysfs, or an actual
hot-unplug, we first remove the procfs and sysfs attributes for the device
before attempting to release the device from any driver bound to it.
Unbinding the driver from the device can take time.  The device might need
to write out data or it might be actively in use.  If it's in use by
userspace through a vfio driver, the unbind might block until the user
releases the device.  This leads to a potentially non-trivial amount of
time where the device exists, but we've torn down the interfaces that
userspace uses to examine devices, for instance lspci might generate this
sort of error:

  pcilib: Cannot open /sys/bus/pci/devices/0000:01:0a.3/config
  lspci: Unable to read the standard configuration space header of device 0000:01:0a.3

We don't seem to have any dependence on this teardown ordering in the
kernel, so let's unbind the driver first, which is also more symmetric with
the instantiation of the device in pci_bus_add_device().

Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: fix incorrect extent state in xfs_bmap_add_extent_unwritten_real

[ Upstream commit 5e422f5e4fd71d18bc6b851eeb3864477b3d842e ]

There was one spot in xfs_bmap_add_extent_unwritten_real that didn't use the
passed in new extent state but always converted to normal, leading to wrong
behavior when converting from normal to unwritten.

Only found by code inspection, it seems like this code path to move partial
extent from written to unwritten while merging it with the next extent is
rarely exercised.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: fix log block underflow during recovery cycle verification

[ Upstream commit 9f2a4505800607e537e9dd9dea4f55c4b0c30c7a ]

It is possible for mkfs to format very small filesystems with too
small of an internal log with respect to the various minimum size
and block count requirements. If this occurs when the log happens to
be smaller than the scan window used for cycle verification and the
scan wraps the end of the log, the start_blk calculation in
xlog_find_head() underflows and leads to an attempt to scan an
invalid range of log blocks. This results in log recovery failure
and a failed mount.

Since there may be filesystems out in the wild with this kind of
geometry, we cannot simply refuse to mount. Instead, cap the scan
window for cycle verification to the size of the physical log. This
ensures that the cycle verification proceeds as expected when the
scan wraps the end of the log.

Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: cleanup l2tp_tunnel_delete calls

[ Upstream commit 4dc12ffeaeac939097a3f55c881d3dc3523dff0c ]

l2tp_tunnel_delete does not return anything since commit 62b982eeb458
("l2tp: fix race condition in l2tp_tunnel_delete").  But call sites of
l2tp_tunnel_delete still do casts to void to avoid unused return value
warnings.

Kill these now useless casts.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: fix wrong cache_misses statistics

[ Upstream commit c157313791a999646901b3e3c6888514ebc36d62 ]

Currently, Cache missed IOs are identified by s->cache_miss, but actually,
there are many situations that missed IOs are not assigned a value for
s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO
(s->iop.bypass = 1), or the cache_bio allocate failed. In these situations,
it will go to out_put or out_submit, and s->cache_miss is null, which leads
bch_mark_cache_accounting() to treat this IO as a hit IO.

[ML: applied by 3-way merge]

Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: explicitly destroy mutex while exiting

[ Upstream commit 330a4db89d39a6b43f36da16824eaa7a7509d34d ]

mutex_destroy does nothing most of time, but it's better to call
it to make the code future proof and it also has some meaning
for like mutex debug.

As Coly pointed out in a previous review, bcache_exit() may not be
able to handle all the references properly if userspace registers
cache and backing devices right before bch_debug_init runs and
bch_debug_init failes later. So not exposing userspace interface
until everything is ready to avoid that issue.

Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

GFS2: Take inode off order_write list when setting jdata flag

[ Upstream commit cc555b09d8c3817aeebda43a14ab67049a5653f7 ]

This patch fixes a deadlock caused when the jdata flag is set for
inodes that are already on the ordered write list. Since it is
on the ordered write list, log_flush calls gfs2_ordered_write which
calls filemap_fdatawrite. But since the inode had the jdata flag
set, that calls gfs2_jdata_writepages, which tries to start a new
transaction. A new transaction cannot be started because it tries
to acquire the log_flush rwsem which is already locked by the log
flush operation.

The bottom line is: We cannot switch an inode from ordered to jdata
until we eliminate any ordered data pages (via log flush) or any
log_flush operation afterward will create the circular dependency
above. So we need to flush the log before setting the diskflags to
switch the file mode, then we need to remove the inode from the
ordered writes list.

Before this patch, the log flush was done for jdata->ordered, but
that's wrong. If we're going from jdata to ordered, we don't need
to call gfs2_log_flush because the call to filemap_fdatawrite will
do it for us:

   filemap_fdatawrite() -> __filemap_fdatawrite_range()
      __filemap_fdatawrite_range() -> do_writepages()
         do_writepages() -> gfs2_jdata_writepages()
            gfs2_jdata_writepages() -> gfs2_log_flush()

This patch modifies function do_gfs2_set_flags so that if a file
has its jdata flag set, and it's already on the ordered write list,
the log will be flushed and it will be removed from the list
before setting the flag.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Acked-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thermal/drivers/step_wise: Fix temperature regulation misbehavior

[ Upstream commit 07209fcf33542c1ff1e29df2dbdf8f29cdaacb10 ]

There is a particular situation when the cooling device is cpufreq and the heat
dissipation is not efficient enough where the temperature increases little by
little until reaching the critical threshold and leading to a SoC reset.

The behavior is reproducible on a hikey6220 with bad heat dissipation (eg.
stacked with other boards).

Running a simple C program doing while(1); for each CPU of the SoC makes the
temperature to reach the passive regulation trip point and ends up to the
maximum allowed temperature followed by a reset.

This issue has been also reported by running the libhugetlbfs test suite.

What is observed is a ping pong between two cpu frequencies, 1.2GHz and 900MHz
while the temperature continues to grow.

It appears the step wise governor calls get_target_state() the first time with
the throttle set to true and the trend to 'raising'. The code selects logically
the next state, so the cpu frequency decreases from 1.2GHz to 900MHz, so far so
good. The temperature decreases immediately but still stays greater than the
trip point, then get_target_state() is called again, this time with the
throttle set to true *and* the trend to 'dropping'. From there the algorithm
assumes we have to step down the state and the cpu frequency jumps back to
1.2GHz. But the temperature is still higher than the trip point, so
get_target_state() is called with throttle=1 and trend='raising' again, we jump
to 900MHz, then get_target_state() is called with throttle=1 and
trend='dropping', we jump to 1.2GHz, etc ... but the temperature does not
stabilizes and continues to increase.

[  237.922654] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[  237.922678] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[  237.922690] thermal cooling_device0: cur_state=0
[  237.922701] thermal cooling_device0: old_target=0, target=1
[  238.026656] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[  238.026680] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1
[  238.026694] thermal cooling_device0: cur_state=1
[  238.026707] thermal cooling_device0: old_target=1, target=0
[  238.134647] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[  238.134667] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[  238.134679] thermal cooling_device0: cur_state=0
[  238.134690] thermal cooling_device0: old_target=0, target=1

In this situation the temperature continues to increase while the trend is
oscillating between 'dropping' and 'raising'. We need to keep the current state
untouched if the throttle is set, so the temperature can decrease or a higher
state could be selected, thus preventing this oscillation.

Keeping the next_target untouched when 'throttle' is true at 'dropping' time
fixes the issue.

The following traces show the governor does not change the next state if
trend==2 (dropping) and throttle==1.

[ 2306.127987] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2306.128009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 2306.128021] thermal cooling_device0: cur_state=0
[ 2306.128031] thermal cooling_device0: old_target=0, target=1
[ 2306.231991] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2306.232016] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1
[ 2306.232030] thermal cooling_device0: cur_state=1
[ 2306.232042] thermal cooling_device0: old_target=1, target=1
[ 2306.335982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2306.336006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=1
[ 2306.336021] thermal cooling_device0: cur_state=1
[ 2306.336034] thermal cooling_device0: old_target=1, target=1
[ 2306.439984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2306.440008] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0
[ 2306.440022] thermal cooling_device0: cur_state=1
[ 2306.440034] thermal cooling_device0: old_target=1, target=0

[ ... ]

After a while, if the temperature continues to increase, the next state becomes
2 which is 720MHz on the hikey. That results in the temperature stabilizing
around the trip point.

[ 2455.831982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2455.832006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=0
[ 2455.832019] thermal cooling_device0: cur_state=1
[ 2455.832032] thermal cooling_device0: old_target=1, target=1
[ 2455.935985] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2455.936013] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0
[ 2455.936027] thermal cooling_device0: cur_state=1
[ 2455.936040] thermal cooling_device0: old_target=1, target=1
[ 2456.043984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2456.044009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0
[ 2456.044023] thermal cooling_device0: cur_state=1
[ 2456.044036] thermal cooling_device0: old_target=1, target=1
[ 2456.148001] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2456.148028] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 2456.148042] thermal cooling_device0: cur_state=1
[ 2456.148055] thermal cooling_device0: old_target=1, target=2
[ 2456.252009] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2456.252041] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0
[ 2456.252058] thermal cooling_device0: cur_state=2
[ 2456.252075] thermal cooling_device0: old_target=2, target=1

IOW, this change is needed to keep the state for a cooling device if the
temperature trend is oscillating while the temperature increases slightly.

Without this change, the situation above leads to a catastrophic crash by a
hardware reset on hikey. This issue has been reported to happen on an OMAP
dra7xx also.

Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ppp: Destroy the mutex when cleanup

[ Upstream commit f02b2320b27c16b644691267ee3b5c110846f49e ]

The mutex_destroy only makes sense when enable DEBUG_MUTEX. For the
good readbility, it's better to invoke it in exit func when the init
func invokes mutex_init.

Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: tegra: Fix cclk_lp divisor register

[ Upstream commit 54eff2264d3e9fd7e3987de1d7eba1d3581c631e ]

According to comments in code and common sense, cclk_lp uses its
own divisor, not cclk_g's.

Fixes: b08e8c0ecc42 ("clk: tegra: add clock support for Tegra30")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: imx6: refine hdmi_isfr's parent to make HDMI work on i.MX6 SoCs w/o VPU

[ Upstream commit c68ee58d9ee7b856ac722f18f4f26579c8fbd2b4 ]

On i.MX6 SoCs without VPU (in my case MCIMX6D4AVT10AC), the hdmi driver
fails to probe:

[    2.540030] dwhdmi-imx 120000.hdmi: Unsupported HDMI controller
(0000:00:00)
[    2.548199] imx-drm display-subsystem: failed to bind 120000.hdmi
(ops dw_hdmi_imx_ops): -19
[    2.557403] imx-drm display-subsystem: master bind failed: -19

That's because hdmi_isfr's parent, video_27m, is not correctly ungated.
As explained in commit 5ccc248cc537 ("ARM: imx6q: clk: Add support for
mipi_core_cfg clock as a shared clock gate"), video_27m is gated by
CCM_CCGR3[CG8].

On i.MX6 SoCs with VPU, the hdmi is working thanks to the
CCM_CMEOR[mod_en_ov_vpu] bit which makes the video_27m ungated whatever
is in CCM_CCGR3[CG8]. The issue can be reproduced by setting
CCMEOR[mod_en_ov_vpu] to 0.

Make the HDMI work in every case by setting hdmi_isfr's parent to
mipi_core_cfg.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: mediatek: add the option for determining PLL source clock

[ Upstream commit c955bf3998efa3355790a4d8c82874582f1bc727 ]

Since the previous setup always sets the PLL using crystal 26MHz, this
doesn't always happen in every MediaTek platform. So the patch added
flexibility for assigning extra member for determining the PLL source
clock.

Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>