drm/vc4: Adjust modes in DSI to work around the integer PLL divider.

BCM2835's PLLD_DSI1 divider doesn't give us many choices for our pixel
clocks, so to support panels on the Raspberry Pi we need to set a
higher pixel clock rate than requested and adjust the mode we program
to extend out the HFP so that the refresh rate matches.

v2: Drop an unfinished comment (caught by Noralf)

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511235625.22427-2-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/vc4: fix spelling mistake: "dimesions" -> "dimensions"

Trivial fix to spelling mistake in DRM_ERROR message and split
over two lines to clean up a "line over 80 characters" checkpatch
warning.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170514170016.6802-1-colin.king@canonical.com

drm/vc4: Enable selection in Kconfig on any 32-bit BCM platform.

With the Cygnus port, we needed to add at least "|| ARCH_BCM_CYGNUS"
to let the module get built on a cygnus-only kernel.  However, I
anticipate having a port for Kona soon, so just present the module on
all of BCM.

v2: Keep allowing selection with ARCH_BCM2835, since ARCH_BCM doesn't
    exist on arm64.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509181539.30278-1-eric@anholt.net

drm/cirrus: fix include notation and remove -Iinclude/drm flag

Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-8-git-send-email-yamada.masahiro@socionext.com

drm/bridge: fix include notation and remove -Iinclude/drm flag

Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.

While we are here, sort the touched parts alphabetically.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-7-git-send-email-yamada.masahiro@socionext.com

drm/bochs: fix include notation and remove -Iinclude/drm flag

Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-6-git-send-email-yamada.masahiro@socionext.com

drm/ast: fix include notation and remove -Iinclude/drm flag

Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-5-git-send-email-yamada.masahiro@socionext.com

drm/amd: fix include notation and remove -Iinclude/drm flag

Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-4-git-send-email-yamada.masahiro@socionext.com

drm/ttm: fix include notation and remove -Iinclude/drm flag

For the C file, include <drm/*.h> instead of relative path from
include/drm.

For headers in include/drm/ttm, simplify the <tty/*.h> with "*.h".

This allows us to remove the -Iinclude/drm compiler flag from
drivers/gpu/drm/ttm/Makefile (and from other drivers' Makefiles).

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-3-git-send-email-yamada.masahiro@socionext.com

drm: make drm_panel.h self-contained

-ENOSYS and -EINVAL are referenced in some static inline functions.
of_drm_find_pane() takes a pointer to struct device_node.

Make this header self-contained to not depend on specific include
order.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-2-git-send-email-yamada.masahiro@socionext.com

drm: add missing declaration to drm_blend.h

drm_blend.h is missing declaration for 'struct drm_plane'. Add it.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1494938085-21805-1-git-send-email-tomi.valkeinen@ti.com

drm/dp: Wait up all outstanding tx waiters

As we can have multiple tx in the queue, with individual waiters, make
sure that all are woken when any state changes (so that we are sure the
right owner of the txmsg is woken).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170513105201.17658-2-chris@chris-wilson.co.uk

drm/dp: Read the tx msg state once after checking for an event

Both as an exercise to document that we are reading the state outside of
the appropriate mutex and to ensure that we only read the value once
before the multiple comparisons, use READ_ONCE.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170513105201.17658-1-chris@chris-wilson.co.uk

drm/prime: Forward declare struct device

We need a declaration of struct device to avoid warnings:

In file included from include/drm/drm_file.h:38:0,
                 from drivers/gpu/drm/drm_file.c:38:
include/drm/drm_prime.h:71:14: warning: 'struct device' declared inside
  parameter list will not be visible outside of this definition or
  declaration
          struct device *attach_dev);
 ^~~~~~

Forward declare it.

Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1494435925-9457-1-git-send-email-labbott@redhat.com

drm/vblank: Lock down vblank->hwmode more

In the previous patch we've implemented hwmode tracking a la i915 for
the vblank timestamp calculations. But that was just the basic
semantics, i915 has some nice sanity checks to make sure we keep
getting this right. Move them over too.

v2:
- WARN_ON_ONCE to avoid excessive spam (Ville)
- Really only WARN on atomic drivers.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-5-daniel.vetter@ffwll.ch

drm/vblank: drop the mode argument from drm_calc_vbltimestamp_from_scanoutpos

If we restrict this helper to only kms drivers (which is the case) we
can look up the correct mode easily ourselves. But it's a bit tricky:

- All legacy drivers look at crtc->hwmode. But that is updated already
  at the beginning of the modeset helper, which means when we disable
  a pipe. Hence the final timestamps might be a bit off. But since
  this is an existing bug I'm not going to change it, but just try to
  be bug-for-bug compatible with the current code. This only applies
  to radeon&amdgpu.

- i915 tries to get it perfect by updating crtc->hwmode when the pipe
  is off (i.e. vblank->enabled = false).

- All other atomic drivers look at crtc->state->adjusted_mode. Those
  that look at state->requested_mode simply don't adjust their mode,
  so it's the same. That has two problems: Accessing crtc->state from
  interrupt handling code is unsafe, and it's updated before we shut
  down the pipe. For nonblocking modesets it's even worse.

For atomic drivers try to implement what i915 does. To do that we add
a new hwmode field to the vblank structure, and update it from
drm_calc_timestamping_constants(). For atomic drivers that's called
from the right spot by the helper library already, so all fine. But
for safety let's enforce that.

For legacy driver this function is only called at the end (oh the
fun), which is broken, so again let's not bother and just stay
bug-for-bug compatible.

The  benefit is that we can use drm_calc_vbltimestamp_from_scanoutpos
directly to implement ->get_vblank_timestamp in every driver, deleting
a lot of code.

v2: Completely new approach, trying to mimick the i915 solution.

v3: Fixup kerneldoc.

v4: Drop the WARN_ON to check that the vblank is off, atomic helpers
currently unconditionally call this. Recomputing the same stuff should
be harmless.

v5: Fix typos and move misplaced hunks to the right patches (Neil).

v6: Undo hunk movement (kbuild).

Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-4-daniel.vetter@ffwll.ch

drm/vblank: Add FIXME comments about moving the vblank ts hooks

This is going to be a bit too much, but good to have at least a small
note about where this should all head towards.

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-3-daniel.vetter@ffwll.ch

drm/vblank: Switch to bool in_vblank_irq in get_vblank_timestamp

It's overkill to have a flag parameter which is essentially used just
as a boolean. This takes care of core + adjusting drivers.

Adjusting the scanout position callback is a bit harder, since radeon
also supplies it's own driver-private flags in there.

v2: Fixup misplaced hunks (Neil).

v3: kbuild says v1 was better ...

Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-2-daniel.vetter@ffwll.ch

drm/vblank: Switch drm_driver->get_vblank_timestamp to return a bool

There's really no reason for anything more:
- Calling this while the crtc vblank stuff isn't set up is a driver
  bug. Those places alrready DRM_ERROR.
- Calling this when the crtc is off is either a driver bug (calling
  drm_crtc_handle_vblank at the wrong time) or a core bug (for
  anything else). Again, we DRM_ERROR.
- EINVAL is checked at higher levels already, and if we'd use struct
  drm_crtc * instead of (dev, pipe) it would be real obvious that
  those are again core bugs.

The only valid failure mode is crap hardware that couldn't sample a
useful timestamp, to ask the core to just grab a not-so-accurate
timestamp. Bool is perfectly fine for that.

v2: Also fix up the one caller, I lost that in the shuffling (Jani).

v3: Fixup commit message (Neil).

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-1-daniel.vetter@ffwll.ch

drm/vgem: Convert to a struct drm_device subclass

With Laura's introduction of the fake platform device for importing
dmabuf, we add a second static that is logically tied to the vgem_device.
Convert vgem over to using the struct drm_device subclassing, so that
the platform device is stored inside its owner.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508132228.9509-1-chris@chris-wilson.co.uk

gpu: drm: gma500: remove dead code

Local variable use_gct is assigned to a constant value and it is never
updated again. Remove this variable and the dead code it guards.

Addresses-Coverity-ID: 145690
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509152221.GA7618@embeddedgus

drm/sti: Adjust two checks for null pointers in sti_hqvdp_probe()

MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

The script “checkpatch.pl” pointed information out like the following.

Comparison to NULL could be written !…

Thus fix the affected source code places.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/918229e6-80fe-629f-8fec-bf60ac15275f@users.sourceforge.net

drm/sti: Fix typos in a comment line

Adjust this description for a function call.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/e70bf37b-a461-873e-4ba3-40bf43cc7b21@users.sourceforge.net

drm/sti: Fix a typo in a comment line

Add a missing character in this description for a data structure.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/a5a1f6cb-ba9d-0f7d-9126-9aeffb3783ad@users.sourceforge.net

drm/sti: Replace 17 seq_puts() calls by seq_putc()

Single characters should be put into a sequence at several places.
Thus use the corresponding function "seq_putc".

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/5b4e2964-0742-8367-976f-678356d9347a@users.sourceforge.net

drm/sti: Reduce function calls for sequence output at five places

Some data were put into a sequence by separate function calls.
Print the same data by five single function calls instead.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1f5c5b0d-77c4-6efc-7906-cee76c33d2b0@users.sourceforge.net

drm/sti: use seq_puts to display a string

gdp_dbg_ctl() uses seq_printf() to display a color format name even
though there is no format string. When using -Wformat-string, gcc
reports the following warning:

    drivers/gpu/drm/sti/sti_gdp.c: In function 'gdp_dbg_ctl':
    drivers/gpu/drm/sti/sti_gdp.c:150:18: warning: format not a string
    literal and no format arguments [-Wformat-security]
        seq_printf(s, gdp_format_to_str[i].name);
                      ^~~~~~~~~~~~~~~~~

Silence this warning by using seq_puts() instead.

Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331192507.20538-1-nicolas.iooss_linux@m4x.org

drm: Nerf the preclose callback for modern drivers

With all drivers converted there's only legacy dri1 drivers using it.
Not going to touch those, instead just hide it like we've done with
other dri1 driver hooks like firstopen.

In all this I didn't find any real reason why we'd needed 2 hooks, and
having symmetry between open and close just appeases my OCD better.
Yeah, someone else could do an s/postclose/close/, but that's for
someone who understands cocci. And maybe after this series is reviewed
and landed, to avoid patch-regen churn.

v2: s/last/post/close in the kernel-doc (Sean).

Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508082633.4214-4-daniel.vetter@ffwll.ch

drm/exynos: Merge pre/postclose hooks

Again no apparent explanation for the split except hysterical raisins.
Merging them also makes it a bit more obviuos what's going on wrt the
runtime pm refdancing.

Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508082633.4214-3-daniel.vetter@ffwll.ch

drm/tegra: switch to postclose

I didn't spot anything that would require ordering here (well not
anywhere else either), and I'm trying to unify at least modern drivers
on one close hook.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508082633.4214-2-daniel.vetter@ffwll.ch

drm/nouveau: Merge pre/postclose hooks

Again no apparent explanation for the split except hysterical raisins.
Merging them also makes it a bit more obviuos what's going on wrt the
runtime pm refdancing.

Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508082633.4214-1-daniel.vetter@ffwll.ch

drm/pl111: Initial drm/kms driver for pl111

This is a modesetting driver for the pl111 CLCD display controller
found on various ARM platforms such as the Versatile Express. The
driver has only been tested on the bcm911360_entphn platform so far,
with PRIME-based buffer sharing between vc4 and clcd.

It reuses the existing devicetree binding, while not using quite as
many of its properties as the fbdev driver does (those are left for
future work).

v2: Nearly complete rewrite by anholt, cutting 2/3 of the code thanks
    to DRM core's excellent new helpers.
v3: Don't match pl110 any more, don't attach if we don't have a DRM
    panel, use DRM_GEM_CMA_FOPS, update MAINTAINERS, use the simple
    display helper, use drm_gem_cma_dumb_create (same as our wrapper).
v4: Change the driver's .name to not clash with fbdev in sysfs, drop
    platform alias, drop redundant "drm" in DRM driver name, hook up
    .prepare_fb to the CMA helper so that DMA fences should work.
v5: Move register definitions inside the driver directory, fix build
    in COMPILE_TEST and !AMBA mode.
v6: Drop TIM2_CLKSEL for now to be consistent with existing DT
    bindings, switch back to external register definitions.

Signed-off-by: Tom Cooksey <tom.cooksey@arm.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> (v5)
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170413031746.12921-2-eric@anholt.net

video: ARM CLCD: Move registers to a separate header.

We'd like to reuse these register definitions for the DRM CLCD driver,
but there's a bunch of fbdev-specific code in the current header.

v2: Add #ifndef guard.

Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170413031746.12921-1-eric@anholt.net

drm/vc4: Add specific compatible strings for Cygnus.

Cygnus has V3D 2.6 instead of 2.1, and doesn't use the VC4 display
modules.  The V3D can be uniquely identified by the IDENT[01]
registers, and there's nothing to key off of for the display change
other than the lack of DT nodes for the display components, but it's
convention to have new compatible strings anyway.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170428224223.21904-3-eric@anholt.net

drm/vc4: Don't try to initialize FBDEV if we're only bound to V3D.

There's no sense in having an fbdev if there's no display, since
connectors don't get hotplugged to this hardware.  On Cygnus we were
getting a dmesg error from passing in num_connectors (0), when that
argument is supposed to be the maximum number of cloned connectors per
CRTC (1).

Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170428224223.21904-2-eric@anholt.net

drm/vc4: Turn the V3D clock on at runtime.

For the Raspberry Pi's bindings, the power domain also implicitly
turns on the clock and deasserts reset, but for the new Cygnus port we
start representing the clock in the devicetree.

v2: Document the clock-names property, check for -ENOENT for no clock
    in DT.
v3: Drop NULL checks around clk calls which embed NULL checks.
v4: Drop clk-names (feedback by Rob Herring)

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170428224223.21904-1-eric@anholt.net

drm: Remove redundant NULL check during atomic plane commit

plane_state can't be NULL anywhere in this function, so the NULL check
at the end is redundant, remove it.

Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1493214013-15580-9-git-send-email-imre.deak@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

dma-buf: Use seq_putc() in two functions

Three single characters (line breaks) should be put into a sequence.
Thus use the corresponding function "seq_putc".

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/b8a85220-039a-e4bb-c74b-d76baab234e8@users.sourceforge.net

dma-buf: Adjust a null pointer check in dma_buf_attach()

The script "checkpatch.pl" pointed information out like the following.

Comparison to NULL could be written "!attach"

Thus adjust this expression.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>

dma-buf: Improve a size determination in dma_buf_attach()

Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>

dma-buf: Combine two function calls into one in dma_buf_debug_show()

A bit of data was put into a sequence by two separate function calls.
Print the same data by a single function call instead.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>

drm/atomic: Add support for custom scaling mode properties, v2

Some connectors may not allow all scaling mode properties, this function will allow
creating the scaling mode property with only the supported subset. It also wires up
this state for atomic.

This will make it possible to convert i915 connectors to atomic.

Changes since v1:
 - Add DRM_MODE_PROP_ENUM flag to drm_property_create
 - Use the correct index in drm_property_add_enum.
 - Add DocBook for function (Sean Paul).
 - Warn if less than 2 valid scaling modes are passed.
 - Remove level of indent. (Sean Paul)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-3-maarten.lankhorst@linux.intel.com
[mlankhorst: Rename function, fix docbook issues]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/atomic: Handle picture_aspect_ratio in atomic core

This is only used in i915, which had used its own non-atomic way to
deal with the picture aspect ratio. Move selected aspect_ratio to
atomic state and use the atomic state in the affected i915 connectors.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-2-maarten.lankhorst@linux.intel.com
[mlankhorst: taomic -> atomic thanks to Manasi's input]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/vgem: Enable dmabuf import interfaces

Enable the GEM dma-buf import interfaces in addition to the export
interfaces. This lets vgem be used as a test source for other allocators
(e.g. Ion).

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493923548-20878-4-git-send-email-labbott@redhat.com

drm/prime: Introduce drm_gem_prime_import_dev

The existing drm_gem_prime_import function uses the underlying
struct device of a drm_device for attaching to a dma_buf. Some drivers
(notably vgem) may not have an underlying device structure. Offer
an alternate function to attach using any available device structure.

Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493923548-20878-3-git-send-email-labbott@redhat.com

drm/vgem: Add a dummy platform device

The vgem driver is currently registered independent of any actual
device. Some usage of the dmabuf APIs require an actual device structure
to do anything. Register a dummy platform device for use with dmabuf.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493923548-20878-2-git-send-email-labbott@redhat.com

drm/i915: Track MST link bandwidth

Use the added helpers to track MST link bandwidth for atomic modesets.
Link bw is acquired in the ->atomic_check() phase when CRTCs are being
enabled with drm_atomic_find_vcpi_slots(). Similarly, link bw is released
during ->atomic_check() with the connector helper callback ->atomic_check()
when CRTCs are disabled.

v6: active_changed does not alter vcpi allocations (Maarten)
v5: Implement connector->atomic_check() in place of atomic_release()
v4: Return an int from intel_dp_mst_atomic_release() (Maarten)
v3:
 Handled the case where ->atomic_release() is called more than once
 during an atomic_check() for the same state.
v2:
 Squashed atomic_release() implementation and caller (Daniel)
 Fixed logic for connector-crtc switching case (Daniel)
 Fixed logic for suspend-resume case.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Harry Wentland <Harry.wentland@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1493421260-3146-1-git-send-email-dhinakaran.pandiyan@intel.com

drm/dp: Add DP MST helpers to atomically find and release vcpi slots

drm_dp_atomic_find_vcpi_slots() should be called from ->atomic_check() to
check there are sufficient vcpi slots for a mode and to add that to the
state. This should be followed by a call to drm_dp_mst_allocate_vcpi()
in ->atomic_commit() to initialize a struct vcpi for the port.

drm_dp_atomic_release_vcpi_slots() should be called from
->atomic_check() to release a port's vcpi slot allocation from the
state.

Drivers that do not make use of this atomic helper are expected to call
drm_dp_find_vcpi_slots() instead before calling
drm_dp_mst_allocate_vcpi().

v3: drm_dp_atomic_release_vcpi_slots() now needs to know how many slots
    to release as we may not have a valid reference to port.
v2:
Added checks for verifying the port reference is valid
Moved get_mst_topology_state() into the helpers (Daniel)
Changed find_vcpi_slots() to not depend on current allocation

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Harry Wentland <Harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1492753893-3748-4-git-send-email-dhinakaran.pandiyan@intel.com

drm/dp: Introduce MST topology state to track available link bandwidth

Link bandwidth is shared between multiple display streams in DP MST
configurations. The DP MST topology manager structure maintains the
shared link bandwidth for a primary link directly connected to the GPU. For
atomic modesetting drivers, checking if there is sufficient link bandwidth
for a mode needs to be done during the atomic_check phase to avoid failed
modesets. Let's encapsulate the available link bw information in a
private state structure so that bw can be allocated and released atomically
for each of the ports sharing the primary link.

v3: WARN_ON() if connection_mutex is not held (Archit)
v2: Included kernel doc, moved state initialization and switched to
kmemdup() for allocation (Daniel)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Harry Wentland <Harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1492753893-3748-3-git-send-email-dhinakaran.pandiyan@intel.com

drm: Add driver-private objects to atomic state

It is necessary to track states for objects other than connector, crtc
and plane for atomic modesets. But adding objects like DP MST link
bandwidth to drm_atomic_state would mean that a non-core object will be
modified by the core helper functions for swapping and clearing
it's state. So, lets add void * objects and helper functions that operate
on void * types to keep these objects and states private to the core.
Drivers can then implement specific functions to swap and clear states.
The other advantage having just void * for these objects in
drm_atomic_state is that objects of different types can be managed in the
same state array.

v7: Use __for_each_private_obj to define for_each_private_obj (Maarten)
v6: More kernel-doc to keep 0-day happy
v5: Remove more NULL checks (Maarten)
v4: Avoid redundant NULL checks when private_objs array is empty (Maarten)
v3: Macro alignment (Chris)
v2: Added docs and new iterator to filter private objects (Daniel)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Harry Wentland <Harry.wentland@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1492753893-3748-2-git-send-email-dhinakaran.pandiyan@intel.com

Merge tag 'drm-for-v4.12' of git://people.freedesktop.org/~airlied/linux into drm-misc-next

Backmerging Dave's 'drm-for-v4.12' pull request now that it's landed. There are
a bunch of non-drm changes which are just random bits we hadn't yet picked up in
misc-next.

main drm pull request for 4.12 kernel

Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/CAPM=9ty0jHgzG18zOr5CYODyTqZfH55kOCOFqNnXiWnTb_uNWw@mail.gmail.com

drm/mm: Split up long running selftests with cond_resched()

Scatter a few cond_resched() in between phases of the drm_mm selftests
to try and prevent us incurring the wrath of the NMI watchdog.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170329091053.13837-1-chris@chris-wilson.co.uk

drm: zte: add VGA driver support

It adds VGA driver support, which needs to configure corresponding VOU
interface in RGB_888 format, and thus the following changes are needed
on zx_vou.

 - Rename the CSC block of Graphic Layer a bit to make it more specific,
   and add CSC of Channel to support RGB output.
 - Bypass Dither block for RGB output.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491910226-7831-1-git-send-email-shawnguo@kernel.org

dt-bindings: display: add support for ZTE VGA device

It adds bindings doc for ZTE VOU VGA output device.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491490870-6330-4-git-send-email-shawnguo@kernel.org

drm: zte: move CSC register definitions into a common header

The CSC (Color Space Conversion) block in VOU is used by not only
Graphic Layer (plane) but also channel (CRTC) module.  Let's move
its register definitions into a common header, so that CRTC driver can
include it when needed.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491490870-6330-3-git-send-email-shawnguo@kernel.org

drm: zte: do not enable clock auto-gating by default

Some VOU modules do not work well with clock auto-gating.  For example,
VGA I2C bus will fail to read EDID data from monitor.  Let's not enable
this feature by default, and leave it to the possible future low-power
optimization.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491490870-6330-2-git-send-email-shawnguo@kernel.org

drm/atomic: fix doc to use new name for commit types

Use "non-blocking" and "blocking" instead of old names.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427143506.32650-1-gustavo@padovan.org

drm/rockchip: analogix_dp: Remove unused check and variables

Remove unused check and variables after:
drm/rockchip: Set line flag config register in vop_crtc_enable

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1493469547-2121-1-git-send-email-jeffy.chen@rock-chips.com

drm: Make drm_atomic_replace_property_blob_from_id() more generic

Change drm_atomic_replace_property_blob_from_id()'s first parameter
from drm_crtc to drm_device, so that the function can be used for other
drm_mode_objects too.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/851b8504c7f294a10645ba6f6d391ac9764068b7.1492768073.git.jsarha@ti.com

drm: drm_color_mgmt.h needs struct drm_crtc declaration

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/69c913b3ae3fc7235c059e08f58fb0a172d98cf8.1492768073.git.jsarha@ti.com

Merge branch 'linux-4.12' of git://github.com/skeggsb/linux into drm-next

Some nouveau regression fixes.

* 'linux-4.12' of git://github.com/skeggsb/linux:
  drm/nouveau/fb/gf100-: Fix 32 bit wraparound in new ram detection
  drm/nouveau/secboot/gm20b: fix the error return code in gm20b_secboot_tegra_read_wpr()
  drm/nouveau/kms: Increase max retries in scanout position queries.
  drm/nouveau/bios/bitP: check that table is long enough for optional pointers
  drm/nouveau/fifo/nv40: no ctxsw for pre-nv44 mpeg engine

drm/nouveau/fb/gf100-: Fix 32 bit wraparound in new ram detection

A missing u64 cast causes a 32-Bit wraparound from
4096 MiB to 0 MiB and therefore total 0 MiB VRAM detected
if card has 4096 Mib per FBP.

Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

drm/nouveau/secboot/gm20b: fix the error return code in gm20b_secboot_tegra_read_wpr()

The error return code PTR_ERR(mc) is always 0 since mc is
equal to 0 in this error handling case.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

drm/nouveau/kms: Increase max retries in scanout position queries.

So far we only allowed for 1 retry and just failed the query
- and thereby high precision vblank timestamping - if we did
not get a reasonable result, as such a failure wasn't considered
all too horrible. There are a few NVidia gpu models out there which
may need a bit more than 1 retry to get a successful query result
under some conditions.

Since Linux 4.4 the update code for vblank counter and timestamp
in drm_update_vblank_count() changed so that the implementation
assumes that high precision vblank timestamping of a kms driver
either consistently succeeds or consistently fails for a given
video mode and encoder/connector combo. Iow. switching from success
to fail or vice versa on a modeset or connector change is ok, but
spurious temporary failure for a given setup can confuse the core
code and potentially cause bad miscounting of vblanks and confusion
or hangs in userspace clients which rely on vblank  stuff, e.g.,
desktop compositors.

Therefore change the max retry count to a larger number - more than
any gpu so far is known to need to succeed, but still low enough
so that these queries which do also happen in vblank interrupt are
still fast enough to be not disastrously long if something would
go badly wrong with them.

As such sporadic retries only happen seldom even on affected gpu's,
this could mean a vblank irq could take a few dozen microseconds
longer every few hours of uptime -- better than a desktop compositor
randomly hanging every couple of hours or days of uptime in a hard
to reproduce manner.

Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

drm/nouveau/bios/bitP: check that table is long enough for optional pointers

Fixes OOB VBIOS accesses on some boards.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

drm/nouveau/fifo/nv40: no ctxsw for pre-nv44 mpeg engine

Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>

Merge tag 'drm-intel-next-fixes-2017-04-27' of git://anongit.freedesktop.org/git/drm-intel into drm-next

drm/i915 and gvt fixes for drm-next/v4.12

* tag 'drm-intel-next-fixes-2017-04-27' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915: Confirm the request is still active before adding it to the await
  drm/i915: Avoid busy-spinning on VLV_GLTC_PW_STATUS mmio
  drm/i915/selftests: Allocate inode/file dynamically
  drm/i915: Fix system hang with EI UP masked on Haswell
  drm/i915: checking for NULL instead of IS_ERR() in mock selftests
  drm/i915: Perform link quality check unconditionally during long pulse
  drm/i915: Fix use after free in lpe_audio_platdev_destroy()
  drm/i915: Use the right mapping_gfp_mask for final shmem allocation
  drm/i915: Make legacy cursor updates more unsynced
  drm/i915: Apply a cond_resched() to the saturated signaler
  drm/i915: Park the signaler before sleeping
  drm/i915/gvt: fix a bounds check in ring_id_to_context_switch_event()
  drm/i915/gvt: Fix PTE write flush for taking runtime pm properly
  drm/i915/gvt: remove some debug messages in scheduler timer handler
  drm/i915/gvt: add mmio init for virtual display
  drm/i915/gvt: use directly assignment for structure copying
  drm/i915/gvt: remove redundant ring id check which cause significant CPU misprediction
  drm/i915/gvt: remove redundant platform check for mocs load/restore
  drm/i915/gvt: Align render mmio list to cacheline
  drm/i915/gvt: cleanup some too chatty scheduler message

Merge branch 'drm-vmwgfx-next' of git://people.freedesktop.org/~syeh/repos_linux into drm-next

trivial patch.

* 'drm-vmwgfx-next' of git://people.freedesktop.org/~syeh/repos_linux:
  drm/vmwgfx: Convert macro to octal representation

Merge branch 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld into drm-next

Latest updates on Mali DP, adding support for colour management,
plane scaling and power management.

(these have been in -next for a while).

* 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld:
  drm: mali-dp: use div_u64 for expensive 64-bit divisions
  drm: mali-dp: Check the mclk rate and allow up/down scaling
  drm: mali-dp: Enable image enhancement when scaling
  drm: mali-dp: Add plane upscaling support
  drm/mali-dp: Add core_id file to the sysfs interface
  drm: mali-dp: Add CTM support
  drm: mali-dp: enable gamma support
  drm: mali-dp: add malidp_crtc_state struct
  drm: mali-dp: add custom reset hook for planes
  drm: mali-dp: remove unused variable
  drm: mali-dp: add atomic_print_state for planes
  drm: mali-dp: Enable power management for the device.
  drm: mali-dp: Update the state of all planes before re-enabling active CRTCs.

dma-buf: avoid scheduling on fence status query v2

When a timeout of zero is specified, the caller is only interested in
the fence status.

In the current implementation, dma_fence_default_wait will always call
schedule_timeout() at least once for an unsignaled fence. This adds a
significant overhead to a fence status query.

Avoid this overhead by returning early if a zero timeout is specified.

v2: move early return after enable_signaling

Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170426144620.3560-1-andresx7@gmail.com

drm/rockchip: Set line flag config register in vop_crtc_enable

We need to set vop config done after update line flag config, it's a
new requirement for chips newer than rk3368.

Since we would only use line flag irq for vact_end, let's move it to
vop_crtc_enable.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1493276057-4516-1-git-send-email-jeffy.chen@rock-chips.com

drm: mali-dp: use div_u64 for expensive 64-bit divisions

On 32-bit machines, we can't divide 64-bit integers:

drivers/gpu/drm/arm/malidp_crtc.o: In function `malidp_crtc_atomic_check':
malidp_crtc.c:(.text.malidp_crtc_atomic_check+0x3c0): undefined reference to `__aeabi_uldivmod'
malidp_crtc.c:(.text.malidp_crtc_atomic_check+0x3dc): undefined reference to `__aeabi_uldivmod'

This calls the div_u64 function explicitly instead.

Fixes: 4cea4e9f6690 ("drm: mali-dp: Add plane upscaling support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

drm/i915: Confirm the request is still active before adding it to the await

Although we do check the completion-status of the request before
actually adding a wait on it (either to its submit fence or its
completion dma-fence), we currently do not check before adding it to the
dependency lists.

In fact, without checking for a completed request we may try to use the
signaler after it has been retired and its dependency tree freed:

[   60.044057] BUG: KASAN: use-after-free in __list_add_valid+0x1d/0xd0 at addr ffff880348c9e6a0
[   60.044118] Read of size 8 by task gem_exec_fence/530
[   60.044164] CPU: 1 PID: 530 Comm: gem_exec_fence Tainted: G            E   4.11.0-rc7+ #46
[   60.044226] Hardware name: ��������������������������������� ���������������������������������/���������������������������������, BIOS RYBDWi35.86A.0246.2
[   60.044290] Call Trace:
[   60.044337]  dump_stack+0x4d/0x6a
[   60.044383]  kasan_object_err+0x21/0x70
[   60.044435]  kasan_report+0x225/0x4e0
[   60.044488]  ? __list_add_valid+0x1d/0xd0
[   60.044534]  ? kasan_kmalloc+0xad/0xe0
[   60.044587]  __asan_load8+0x5e/0x70
[   60.044639]  __list_add_valid+0x1d/0xd0
[   60.044788]  __i915_priotree_add_dependency+0x67/0x130 [i915]
[   60.044895]  i915_gem_request_await_request+0xa8/0x370 [i915]
[   60.044974]  i915_gem_request_await_dma_fence+0x129/0x140 [i915]
[   60.045049]  i915_gem_do_execbuffer.isra.37+0xb0a/0x26b0 [i915]
[   60.045077]  ? save_stack+0xb1/0xd0
[   60.045105]  ? save_stack_trace+0x1b/0x20
[   60.045132]  ? save_stack+0x46/0xd0
[   60.045158]  ? kasan_kmalloc+0xad/0xe0
[   60.045184]  ? __kmalloc+0xd8/0x670
[   60.045229]  ? drm_ioctl+0x359/0x640 [drm]
[   60.045256]  ? SyS_ioctl+0x41/0x70
[   60.045330]  ? i915_vma_move_to_active+0x540/0x540 [i915]
[   60.045360]  ? tty_insert_flip_string_flags+0xa1/0xf0
[   60.045387]  ? tty_flip_buffer_push+0x63/0x70
[   60.045414]  ? remove_wait_queue+0xa9/0xc0
[   60.045441]  ? kasan_unpoison_shadow+0x35/0x50
[   60.045467]  ? kasan_kmalloc+0xad/0xe0
[   60.045494]  ? kasan_check_write+0x14/0x20
[   60.045568]  i915_gem_execbuffer2+0xdb/0x2a0 [i915]
[   60.045616]  drm_ioctl+0x359/0x640 [drm]
[   60.045705]  ? i915_gem_execbuffer+0x5a0/0x5a0 [i915]
[   60.045751]  ? drm_version+0x150/0x150 [drm]
[   60.045778]  ? compat_start_thread+0x60/0x60
[   60.045805]  ? plist_del+0xda/0x1a0
[   60.045833]  do_vfs_ioctl+0x12e/0x910
[   60.045860]  ? ioctl_preallocate+0x130/0x130
[   60.045886]  ? pci_mmcfg_check_reserved+0xc0/0xc0
[   60.045913]  ? vfs_write+0x196/0x240
[   60.045939]  ? __fget_light+0xa7/0xc0
[   60.045965]  SyS_ioctl+0x41/0x70
[   60.045991]  entry_SYSCALL_64_fastpath+0x17/0x98
[   60.046017] RIP: 0033:0x7feb2baefc47
[   60.046042] RSP: 002b:00007fff56d28e58 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[   60.046075] RAX: ffffffffffffffda RBX: 00007fff56d290a8 RCX: 00007feb2baefc47
[   60.046102] RDX: 00007fff56d29050 RSI: 00000000c0406469 RDI: 0000000000000003
[   60.046129] RBP: 00007fff56d29050 R08: 000055ecc4cd27d0 R09: 00007feb2bda8600
[   60.046154] R10: 0000000000000073 R11: 0000000000000246 R12: 00000000c0406469
[   60.046177] R13: 0000000000000003 R14: 000000000000000f R15: 0000000000000099
[   60.046203] Object at ffff880348c9e680, in cache i915_dependency size: 64
[   60.046225] Allocated:
[   60.046246] PID = 530
[   60.046269]  save_stack_trace+0x1b/0x20
[   60.046292]  save_stack+0x46/0xd0
[   60.046318]  kasan_kmalloc+0xad/0xe0
[   60.046343]  kasan_slab_alloc+0x12/0x20
[   60.046368]  kmem_cache_alloc+0xab/0x650
[   60.046445]  i915_gem_request_await_request+0x88/0x370 [i915]
[   60.046559]  i915_gem_request_await_dma_fence+0x129/0x140 [i915]
[   60.046705]  i915_gem_do_execbuffer.isra.37+0xb0a/0x26b0 [i915]
[   60.046849]  i915_gem_execbuffer2+0xdb/0x2a0 [i915]
[   60.046936]  drm_ioctl+0x359/0x640 [drm]
[   60.046987]  do_vfs_ioctl+0x12e/0x910
[   60.047038]  SyS_ioctl+0x41/0x70
[   60.047090]  entry_SYSCALL_64_fastpath+0x17/0x98
[   60.047139] Freed:
[   60.047179] PID = 530
[   60.047223]  save_stack_trace+0x1b/0x20
[   60.047269]  save_stack+0x46/0xd0
[   60.047317]  kasan_slab_free+0x72/0xc0
[   60.047366]  kmem_cache_free+0x39/0x160
[   60.047512]  i915_gem_request_retire+0x83f/0x930 [i915]
[   60.047657]  i915_gem_request_alloc+0x166/0x600 [i915]
[   60.047799]  i915_gem_do_execbuffer.isra.37+0xad8/0x26b0 [i915]
[   60.047897]  i915_gem_execbuffer2+0xdb/0x2a0 [i915]
[   60.047942]  drm_ioctl+0x359/0x640 [drm]
[   60.047968]  do_vfs_ioctl+0x12e/0x910
[   60.047993]  SyS_ioctl+0x41/0x70
[   60.048019]  entry_SYSCALL_64_fastpath+0x17/0x98
[   60.048044] Memory state around the buggy address:
[   60.048066]  ffff880348c9e580: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
[   60.048105]  ffff880348c9e600: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
[   60.048138] >ffff880348c9e680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[   60.048170]                                ^
[   60.048191]  ffff880348c9e700: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
[   60.048225]  ffff880348c9e780: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc

Note to hit the use-after-free requires us to be passed back a request
via a fence-array, that is from explicit fencing accumulated into a
sync-file fence-array.

Fixes: 52e542090701 ("drm/i915/scheduler: Record all dependencies upon request construction")
Testcase: igt/gem_exec_fence/expired-history
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170422081537.6468-1-chris@chris-wilson.co.uk
(cherry picked from commit ade0b0c965f59176daddbef9c4717354034f9bce)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Avoid busy-spinning on VLV_GLTC_PW_STATUS mmio

The busy-spin, as the first stage of intel_wait_for_register(), is
currently under suspicion for causing:

[   62.034926] NMI watchdog: Watchdog detected hard LOCKUP on cpu 1
[   62.034928] Modules linked in: i2c_dev i915 intel_gtt drm_kms_helper prime_numbers
[   62.034932] CPU: 1 PID: 183 Comm: kworker/1:2 Not tainted 4.11.0-rc7+ #471
[   62.034933] Hardware name:                  /        , BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[   62.034934] Workqueue: pm pm_runtime_work
[   62.034936] task: ffff880275a04ec0 task.stack: ffffc900002d8000
[   62.034936] RIP: 0010:__intel_wait_for_register_fw+0x77/0x1a0 [i915]
[   62.034937] RSP: 0018:ffffc900002dbc38 EFLAGS: 00000082
[   62.034939] RAX: ffffc90003530094 RBX: 0000000000130094 RCX: 0000000000000001
[   62.034940] RDX: 00000000000000a1 RSI: ffff88027fd15e58 RDI: 0000000000000000
[   62.034941] RBP: ffffc900002dbc78 R08: 0000000000000002 R09: 0000000000000000
[   62.034942] R10: ffffc900002dbc18 R11: ffff880276429dd0 R12: ffff8802707c0000
[   62.034943] R13: 00000000000000a0 R14: 0000000000000000 R15: 00000000fffefc10
[   62.034945] FS:  0000000000000000(0000) GS:ffff88027fd00000(0000) knlGS:0000000000000000
[   62.034945] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   62.034947] CR2: 00007ffd3cd98ff8 CR3: 0000000274c19000 CR4: 00000000001006e0
[   62.034947] Call Trace:
[   62.034948]  intel_wait_for_register+0x77/0x140 [i915]
[   62.034949]  vlv_suspend_complete+0x23/0x5b0 [i915]
[   62.034950]  intel_runtime_suspend+0x16c/0x2a0 [i915]
[   62.034950]  pci_pm_runtime_suspend+0x50/0x180
[   62.034951]  ? pci_pm_runtime_resume+0xa0/0xa0
[   62.034952]  __rpm_callback+0xc5/0x210
[   62.034953]  rpm_callback+0x1f/0x80
[   62.034953]  ? pci_pm_runtime_resume+0xa0/0xa0
[   62.034954]  rpm_suspend+0x118/0x580
[   62.034955]  pm_runtime_work+0x64/0x90
[   62.034956]  process_one_work+0x1bb/0x3e0
[   62.034956]  worker_thread+0x46/0x4f0
[   62.034957]  ? __schedule+0x18b/0x610
[   62.034958]  kthread+0xff/0x140
[   62.034958]  ? process_one_work+0x3e0/0x3e0
[   62.034959]  ? kthread_create_on_node+

and related hard lockups in CI for byt and bsw.

Note this effectively reverts commits 41ce405e6894 and b27366958869
("drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()")

v2: Convert bool allow into a u32 mask for clarity and repeat the
comment on vlv rc6 timing to justify the 3ms timeout used for the wait (Ville)

Fixes: 41ce405e6894 ("drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()")
Fixes: b27366958869 ("drm/i915: Convert wait_for(I915_READ(reg)) to intel_wait_for_register()")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100718
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421135815.11897-1-chris@chris-wilson.co.uk
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
(cherry picked from commit 3dd14c04d77d7d702de5aa7157df4cc9417329f3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/selftests: Allocate inode/file dynamically

Avoid having too large a stack by creating the fake struct inode/file on
the heap instead.

drivers/gpu/drm/i915/selftests/mock_drm.c: In function 'mock_file':
drivers/gpu/drm/i915/selftests/mock_drm.c:46:1: error: the frame size of 1328 bytes is larger than 1280 bytes [-Werror=frame-larger-than=]
drivers/gpu/drm/i915/selftests/mock_drm.c: In function 'mock_file_free':
drivers/gpu/drm/i915/selftests/mock_drm.c:54:1: error: the frame size of 1312 bytes is larger than 1280 bytes [-Werror=frame-larger-than=]

Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 66d9cb5d805a ("drm/i915: Mock the GEM device for self-testing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20170419094143.16922-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 2310b3c952c5dc56c2e08f71b907b8e23ab3270d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix system hang with EI UP masked on Haswell

Previously with commit a9c1f90c8e17
("drm/i915: Don't mask EI UP interrupt on IVB|SNB") certain,
seemingly unrelated bit (GEN6_PM_RP_UP_EI_EXPIRED) was needed
to be unmasked for IVB and SNB in order to prevent system hang
with chained batchbuffers.

Our CI was seeing incomplete results with tests that used
chained batches and it was found out that HSW needs to have this
same bit unmasked to reliably survive chained batches.

Always unmask GEN6_PM_RP_UP_EI_EXPIRED on Haswell to
prevent system hang with batch chaining.

Testcase: igt/gem_exec_fence/nb-await-default
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100672
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1492082127-29007-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 3396a273851c14634b98bb27be37508b06df94f4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: checking for NULL instead of IS_ERR() in mock selftests

i915_gem_request_alloc() uses error pointers.  It never returns NULLs.

Fixes: 0daf0113cff6 ("drm/i915: Mock infrastructure for request emission")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170413195217.GA26108@mwanda
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit be02f7556447a0dee672acb5e462f03377b98ae8)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Perform link quality check unconditionally during long pulse

Apparently some DP sinks are a little nuts and cause HPD to drop
intermittently during modesets. This happens eg. on an ASUS PB287Q.
In oder to recover from this we can't really use the previous
connector status to determine if the link needs retraining, so let's
just ignore that piece of information and do the retrain
unconditionally. We do of course still check whether the link is
supposed to be running or not.

To actually get read out the EDID and update things properly we
also need to nuke the goto out added by commit 7d23e3c37bb3
("drm/i915: Cleaning up intel_dp_hpd_pulse"). I'm actually not sure
why that was there. Perhaps to avoid an EDID read if the connector
status didn't appear to change, but that sort of thing is quite racy
and would have failed anyway if we failed to keep up with the
hotplugs (if we missed the HPD down in between two HPD ups). And
now that we take this codepath unconditionally we definitely need
to drop the goto as otherwise we would never do the EDID read.

v2: Drop the goto that made us skip EDID reads entirely. Doh!
v3: Rebase due to locking changes
    s/apparely/apparently/ in the comment (Chris)

Cc: stable@vger.kernel.org
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Reported-by: Palmer Dabbelt <palmer@dabbelt.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99766
References: https://lists.freedesktop.org/archives/intel-gfx/2017-February/119779.html
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170412193017.21029-1-ville.syrjala@linux.intel.com
(cherry picked from commit 1a36147bb93921651f7fbd7a6e522da6c349081b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix use after free in lpe_audio_platdev_destroy()

[31908.547136] BUG: KASAN: use-after-free in intel_lpe_audio_teardown+0x78/0xb0 [i915] at addr ffff8801f7788358
[31908.547297] Read of size 8 by task drv_selftest/3781
[31908.547405] CPU: 0 PID: 3781 Comm: drv_selftest Tainted: G    BU  W       4.10.0+ #451
[31908.547553] Hardware name:                  /        , BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[31908.547682] Call Trace:
[31908.547772]  dump_stack+0x68/0x9f
[31908.547857]  kasan_object_err+0x1c/0x70
[31908.547947]  kasan_report_error+0x1f1/0x4f0
[31908.548038]  ? kfree+0xaa/0x170
[31908.548121]  kasan_report+0x34/0x40
[31908.548211]  ? klist_children_get+0x20/0x30
[31908.548472]  ? intel_lpe_audio_teardown+0x78/0xb0 [i915]
[31908.548567]  __asan_load8+0x5e/0x70
[31908.548824]  intel_lpe_audio_teardown+0x78/0xb0 [i915]
[31908.549080]  intel_audio_deinit+0x28/0x80 [i915]
[31908.549315]  i915_driver_unload+0xe4/0x360 [i915]
[31908.549551]  ? i915_driver_load+0x1d70/0x1d70 [i915]
[31908.549651]  ? trace_hardirqs_on+0xd/0x10
[31908.549885]  i915_pci_remove+0x23/0x30 [i915]
[31908.549978]  pci_device_remove+0x5c/0x100
[31908.550069]  device_release_driver_internal+0x1db/0x2e0
[31908.550165]  driver_detach+0x68/0xc0
[31908.550256]  bus_remove_driver+0x8b/0x150
[31908.550346]  driver_unregister+0x3e/0x60
[31908.550439]  pci_unregister_driver+0x1d/0x110
[31908.550531]  ? find_module_all+0x7a/0xa0
[31908.550791]  i915_exit+0x1a/0x87 [i915]
[31908.550881]  SyS_delete_module+0x264/0x2c0
[31908.550971]  ? free_module+0x430/0x430
[31908.551064]  ? trace_hardirqs_off_caller+0x16/0x110
[31908.551159]  ? trace_hardirqs_on_caller+0x16/0x280
[31908.551256]  ? trace_hardirqs_on_thunk+0x1a/0x1c
[31908.551350]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[31908.551440] RIP: 0033:0x7f1d67312ec7
[31908.551520] RSP: 002b:00007ffebe34e888 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[31908.551650] RAX: ffffffffffffffda RBX: ffffffff811123f6 RCX: 00007f1d67312ec7
[31908.551743] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 0000560d0af476b8
[31908.551837] RBP: ffff880233d87f98 R08: 0000000000000000 R09: 00007ffebe34e8b8
[31908.551930] R10: 00007f1d68adf8c0 R11: 0000000000000206 R12: 0000000000000000
[31908.552023] R13: 0000560d0af46440 R14: 0000000000000034 R15: 00007ffebe34d860
[31908.552121]  ? trace_hardirqs_off_caller+0x16/0x110
[31908.552217] Object at ffff8801f7788000, in cache kmalloc-2048 size: 2048
[31908.552306] Allocated:
[31908.552377] PID = 3781
[31908.552456]  save_stack_trace+0x16/0x20
[31908.552539]  kasan_kmalloc+0xee/0x190
[31908.552627]  __kmalloc+0xdb/0x1b0
[31908.552713]  platform_device_alloc+0x27/0x90
[31908.552804]  platform_device_register_full+0x36/0x220
[31908.553066]  intel_lpe_audio_init+0x41e/0x570 [i915]
[31908.553320]  intel_audio_init+0xd/0x40 [i915]
[31908.553552]  i915_driver_load+0x13f5/0x1d70 [i915]
[31908.553788]  i915_pci_probe+0x65/0xe0 [i915]
[31908.553881]  pci_device_probe+0xda/0x140
[31908.553969]  driver_probe_device+0x400/0x660
[31908.554058]  __driver_attach+0x11c/0x120
[31908.554147]  bus_for_each_dev+0xe6/0x150
[31908.554237]  driver_attach+0x26/0x30
[31908.554325]  bus_add_driver+0x26b/0x3b0
[31908.554412]  driver_register+0xce/0x190
[31908.554502]  __pci_register_driver+0xaf/0xc0
[31908.554589]  0xffffffffa0550063
[31908.554675]  do_one_initcall+0x8b/0x1e0
[31908.554764]  do_init_module+0x102/0x325
[31908.554852]  load_module+0x3aad/0x45e0
[31908.554944]  SyS_finit_module+0x169/0x1a0
[31908.555033]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[31908.555119] Freed:
[31908.555188] PID = 3781
[31908.555266]  save_stack_trace+0x16/0x20
[31908.555349]  kasan_slab_free+0xb0/0x180
[31908.555436]  kfree+0xaa/0x170
[31908.555520]  platform_device_release+0x76/0x80
[31908.555610]  device_release+0x45/0xe0
[31908.555698]  kobject_put+0x11f/0x260
[31908.555785]  put_device+0x12/0x20
[31908.555871]  platform_device_unregister+0x1b/0x20
[31908.556135]  intel_lpe_audio_teardown+0x5c/0xb0 [i915]
[31908.556390]  intel_audio_deinit+0x28/0x80 [i915]
[31908.556622]  i915_driver_unload+0xe4/0x360 [i915]
[31908.556858]  i915_pci_remove+0x23/0x30 [i915]
[31908.556948]  pci_device_remove+0x5c/0x100
[31908.557037]  device_release_driver_internal+0x1db/0x2e0
[31908.557129]  driver_detach+0x68/0xc0
[31908.557217]  bus_remove_driver+0x8b/0x150
[31908.557304]  driver_unregister+0x3e/0x60
[31908.557394]  pci_unregister_driver+0x1d/0x110
[31908.557653]  i915_exit+0x1a/0x87 [i915]
[31908.557741]  SyS_delete_module+0x264/0x2c0
[31908.557834]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[31908.557919] Memory state around the buggy address:
[31908.558005]  ffff8801f7788200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[31908.558127]  ffff8801f7788280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[31908.558255] >ffff8801f7788300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[31908.558374]                                                     ^
[31908.558467]  ffff8801f7788380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[31908.558595]  ffff8801f7788400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

v2: Just leak the memory (8 bytes) as freeing it ourselves is not safe,
and we need to coordinate a proper fix in platform_device itself.

Fixes: eef57324d926 ("drm/i915: setup bridge for HDMI LPE audio driver")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99952
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Jerome Anand <jerome.anand@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20170412080251.30648-1-chris@chris-wilson.co.uk
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 48ae80741da4b8a26b6df0f765713912bc7cc480)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Use the right mapping_gfp_mask for final shmem allocation

Many sightings report the greater prevalence of allocation failures.
This is all due to the incorrect use of mapping_gfp_constraint(), so
remove it in favour of just querying the mapping_gfp_mask() which are
the exact gfp_t we wanted in the first place.

We still do expect a higher chance of reporting ENOMEM, as that is the
intention of using __GFP_NORETRY -- to fail rather than oom after having
reclaimed from our bo caches, and having done a direct|kswapd reclaim
pass.

Reported-by: Jason Ekstrand <jason.ekstrand@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100594
Fixes: 24f8e00a8a2e ("drm/i915: Prefer to report ENOMEM rather than incur the oom for gfx allocations")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170405221514.23251-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit b268d9fe0f10544f5f7a1b7015e2b97075e6215d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Make legacy cursor updates more unsynced

We're clearing the legacy_cursor_update flag before calling
drm_atomic_helper_setup_commit() which means the helper will
wait for the flip to complete before cleaning up the framebuffers.
That's not what we want for the legacy cursor, so let's clear
the flag after setting up the commit.

Also toss in a FIXME about solving these problems in a nicer
way using the fabled vblank workers.

v2: Also unsync with legacy page flips

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Rafael Ristovski <rafael.ristovski@gmail.com>
Fixes: a5509abda48e ("drm/i915: Fix legacy cursor vs. watermarks for ILK-BDW")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170329142123.5923-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit 895203044067af64400cedbc055898bcec98d102)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Apply a cond_resched() to the saturated signaler

If the engine is continually completing nops, we can saturate the
signaler and keep it working indefinitely. This angers the NMI watchdog!

A good example is to disable semaphores on snb and run igt/gem_exec_nop -
the parallel, multi-engine workloads are more than sufficient to hog the
CPU, preventing the system from even processing ICMP echo replies.

v2: Tvrtko dug into cond_resched() on x86 and found that it only
depended upon preempt_count and not tif_need_resched() - which means
that we would always call schedule() at that point.

Fixes: c81d46138da6 ("drm/i915: Convert trace-irq to the breadcrumb waiter")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170404120531.10737-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit a7980a640cbd339aa80f406d1786a275a2c320bc)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Park the signaler before sleeping

If the signal to park arrives before we sleep, then we need to check
kthread_should_park() before sleeping to avoid missing the signal.
Otherwise, if the signal arrives whilst we are processing completed
requests, we will reset the current->state back to TASK_INTERRUPTIBLE
and so miss the wakeup.

Fixes: fe3288b5da2c ("drm/i915: Park the breadcrumbs signaler across a GPU reset")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403105124.8969-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit b1becb88268beb72df6495e35d3d76c138d215bb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge tag 'gvt-next-fixes-2017-04-20' of https://github.com/01org/gvt-linux into drm-intel-next-fixes

gvt-next-fixes-2017-04-20

- some code optimization from Changbin
- debug message cleanup after QoS merge
- misc fixes for display mmio init, reset vgpu warning, etc.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm: mali-dp: Check the mclk rate and allow up/down scaling

When downscaling, mclk needs to be sufficiently higher than pxlclk in
order to be able to fetch the higher-resolution data and produce output
pixels. When not scaling, or when upscaling, mclk can be equal to
pxlclk. Since the driver doesn't control mclk, just ensure that the
requirement is satisfied with the current clock rate.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: Enable image enhancement when scaling

Apply image enhacement when we are upscaling by a factor of 2
or more in either direction.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: Add plane upscaling support

Enable the scaling engine for upscaling a single plane using the polyphase
scaler. No image enhancement support or downscaling yet*, and composition
result scaling is not implemented.

* Downscaling a plane requires mclk > pxlclk.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm/mali-dp: Add core_id file to the sysfs interface

Add a core_id file in the driver's sysfs directory,
exposing the hardware CORE ID. This is useful to allow
userspace to discover the hardware version used.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: Add CTM support

All DPs have a COLORADJ matrix which is applied prior to output gamma.
Attach that to the CTM property. Also, ensure the input CTM's coefficients
can fit in the DP registers' Q3.12 format.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: enable gamma support

Add gamma via the DRM GAMMA_LUT/GAMMA_LUT_SIZE CRTC
properties. The expected LUT size is 4096 in order
to produce as accurate a set of segments as possible.

This version uses only the green channel's gamma curve
to set the hardware curve on DP550/650. For the sake of
simplicity, it uses the same table of coefficients for
all 3 curves on DP500.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

drm: mali-dp: add malidp_crtc_state struct

Add a custom CRTC state struct to enable storing driver's private
state. This patch only adds the base drm_crtc_state struct and
the atomic functions that handle it.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: add custom reset hook for planes

Now that we are using a custom plane state in mali-dp, we need a
bespoke reset that takes into account the larger structure.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[Updated commit message]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: remove unused variable

The newly introduced function causes a harmless build warning:

drivers/gpu/drm/arm/malidp_planes.c: In function 'malidp_plane_atomic_print_state':
drivers/gpu/drm/arm/malidp_planes.c:98:23: error: unused variable 'mp' [-Werror=unused-variable]

The variable serves no purpose here and can be removed.

Fixes: 242f43b69c61 ("drm: mali-dp: add atomic_print_state for planes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: add atomic_print_state for planes

Add function to dump the state of the plane.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: Enable power management for the device.

Enable runtime and system Power Management. Clocks are now managed
from malidp_crtc_{enable,disable} functions. Suspend-to-RAM tested
as working on Juno.

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm: mali-dp: Update the state of all planes before re-enabling active CRTCs.

Mali DP needs to have all the planes that are becoming inactive in the
new state disabled before re-enabling the active CRTC, otherwise we
start streaming out data from old pointers in memory.

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>

drm/vmwgfx: Convert macro to octal representation

Change "S_IRUSR | S_IWUSR" to "0600", it's easier to parse mentally.

This change should be part of commit 50f837371dd9 ("drm/vmwgfx: Revert
"drm/vmwgfx: Replace numeric parameter like 0444 with macro""), but the
patch was truncated somewhere in the patch route, so add the missing
change. Extract from the original commit message:

  commit 50f837371dd9aea5470c06d5d10bc9ca3e8155b6
  Author: Øyvind A. Holm <sunny@sunbase.org>
  Date:   Thu Mar 23 14:54:48 2017 -0700

    drm/vmwgfx: Revert "drm/vmwgfx: Replace numeric parameter like 0444
    with macro"

    This reverts commit 2d8e60e8b074 ("drm/vmwgfx: Replace numeric
    parameter like 0444 with macro")

    The commit belongs to the series of 1285 patches sent to LKML on
    2016-08-02, it changes the representation of file permissions from
    the octal value "0600" to "S_IRUSR | S_IWUSR".

    The general consensus was that the changes does not increase
    readability, quite the opposite; 0600 is easier to parse mentally
    than S_IRUSR | S_IWUSR.

Signed-off-by: Øyvind A. Holm <sunny@sunbase.org>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>

drm/cec: Add CEC over Aux register definitions

Adding DPCD register definitions from the DP 1.3 specification for CEC
over AUX support.

V2: Add DP_ prefix to all defines.
V3: missed prefixes from the ESI1 defines

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1492703263-11494-1-git-send-email-clinton.a.taylor@intel.com

Merge tag 'drm-misc-next-fixes-2017-04-20' of git://anongit.freedesktop.org/git/drm-misc into drm-next

drm-misc-next-fixes-2017-04-20

Core changes:
- Maintain sti via drm-misc (Vincent)
- Rename dma_buf_ops->kmap_* to avoid naming collision (Logan)

Driver changes:
- Fix UHD displays on stih407 (Vincent)
- Fix uninitialized var return in atmel-hlcdc (Dan)

* tag 'drm-misc-next-fixes-2017-04-20' of git://anongit.freedesktop.org/git/drm-misc:
  dma-buf: Rename dma-ops to prevent conflict with kunmap_atomic macro
  drm: atmel-hlcdc: Uninitialized return in atmel_hlcdc_create_outputs()
  drm/sti: fix GDP size to support up to UHD resolution
  MAINTAINERS: add drm/sti driver into drm-misc

drm: Add DPCD definitions for DP 1.4 DSC feature

Display stream compression is supported on DP 1.4 DP
devices. This patch adds the corersponding DPCD
register definitions for DSC.

v4:
* Add DSC Enable DPCD register def (Ander)
v3:
* Add some SHIFTS and MASKS for uniformity (Jani Nikula)
v2:
* Rebased on drm-tip

Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491259870-25613-1-git-send-email-manasi.d.navare@intel.com