git.stricted.de - GitHub/mt8127/android_kernel_alcatel

airo: copying wrong data in airo_get_aplist()

"qual" used to be declared on the stack, but then in 998a5a7d6a ("airo:
reduce stack memory footprint") we made it dynamically allocated.
Unfortunately the memcpy() here was missed and it's still copying stack
memory instead of the data that we want. In other words, "&qual" should
be "qual".

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix uAP TX packet timeout issue

When running heavy traffic we stop the tx queue if the pending
packet count reaches certain threshold. Later, the tx queue should
be woken up as soon as the packet count falls below the threshold.

Current code wakes TX queue up on STA interface only. Removing the
check for STA interface will allow both STA and AP interfaces to
resume transmit when tx_pending count becomes low.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: remove _bh from inner locks

spin_unlock_bh(&txq->lock) already disables softirqs so we don't want
to do it here.  Fixes smatch warnings:

   drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:'
   drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:'

Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix invalid pointer access in the tx path

After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.

This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix a tx rate duration calculation bug

The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix softlockup in AR9485

steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up

Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13

ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.

fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142

Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211

mac80211: stop polling in disassociation

Stop connection monitor poll during disassociation.
This clears the polling flags and if a scan was
deferred it will be run.

Without this fix, if a scan was deferred due to
connection monitoring while disassociation happens,
this scan blocks further scan requests until interface
down/up which causes problems connecting to another AP.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: check sdata_running on ieee80211_set_bitrate_mask

Otherwise, we might call the driver callback before
the interface was uploaded.

Solves the following warning:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x0
Modules linked in: wlcore_sdio wl12xx wl18xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[<c001b964>] (unwind_backtrace+0x0/0x12c) from [<c0495550>] (dump_stack+0x20/0x24)
[<c0495550>] (dump_stack+0x20/0x24) from [<c003ee28>] (warn_slowpath_common+0x5c/0x74)
[<c003ee28>] (warn_slowpath_common+0x5c/0x74) from [<c003eefc>] (warn_slowpath_fmt+0x40/0x48)
[<c003eefc>] (warn_slowpath_fmt+0x40/0x48) from [<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211])
[<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]) from [<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211])
[<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211]) from [<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8)
[<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8) from [<c03e9164>] (netlink_rcv_skb+0x5c/0xc0)
[<c03e9164>] (netlink_rcv_skb+0x5c/0xc0) from [<c03e9ce0>] (genl_rcv+0x28/0x34)
[<c03e9ce0>] (genl_rcv+0x28/0x34) from [<c03e8e74>] (netlink_unicast+0x158/0x234)
[<c03e8e74>] (netlink_unicast+0x158/0x234) from [<c03e93e0>] (netlink_sendmsg+0x218/0x298)
[<c03e93e0>] (netlink_sendmsg+0x218/0x298) from [<c03b4e5c>] (sock_sendmsg+0xa4/0xc0)
[<c03b4e5c>] (sock_sendmsg+0xa4/0xc0) from [<c03b5af4>] (__sys_sendmsg+0x1d8/0x254)
[<c03b5af4>] (__sys_sendmsg+0x1d8/0x254) from [<c03b5ca8>] (sys_sendmsg+0x4c/0x70)
[<c03b5ca8>] (sys_sendmsg+0x4c/0x70) from [<c0013980>] (ret_fast_syscall+0x0/0x3c)

Note that calling the driver can also result
in undefined behaviour since it doesn't have
to deal with calls while down.

Signed-off-by: Eliad Peller <eliad@wizery.com>
[removed timestamps, added note - Johannes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: fix potential deadlock in regulatory

reg_timeout_work() calls restore_regulatory_settings() which
takes cfg80211_mutex.

reg_set_request_processed() already holds cfg80211_mutex
before calling cancel_delayed_work_sync(reg_timeout),
so it might deadlock.

Call the async cancel_delayed_work instead, in order
to avoid the potential deadlock.

This is the relevant lockdep warning:

cfg80211: Calling CRDA for country: XX

======================================================
[ INFO: possible circular locking dependency detected ]
3.4.0-rc5-wl+ #26 Not tainted
-------------------------------------------------------
kworker/0:2/1391 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<bf28ae00>] restore_regulatory_settings+0x34/0x418 [cfg80211]

but task is already holding lock:
((reg_timeout).work){+.+...}, at: [<c0059e94>] process_one_work+0x1f0/0x480

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 ((reg_timeout).work){+.+...}:
       [<c008fd44>] validate_chain+0xb94/0x10f0
       [<c0090b68>] __lock_acquire+0x8c8/0x9b0
       [<c0090d40>] lock_acquire+0xf0/0x114
       [<c005b600>] wait_on_work+0x4c/0x154
       [<c005c000>] __cancel_work_timer+0xd4/0x11c
       [<c005c064>] cancel_delayed_work_sync+0x1c/0x20
       [<bf28b274>] reg_set_request_processed+0x50/0x78 [cfg80211]
       [<bf28bd84>] set_regdom+0x550/0x600 [cfg80211]
       [<bf294cd8>] nl80211_set_reg+0x218/0x258 [cfg80211]
       [<c03c7738>] genl_rcv_msg+0x1a8/0x1e8
       [<c03c6a00>] netlink_rcv_skb+0x5c/0xc0
       [<c03c7584>] genl_rcv+0x28/0x34
       [<c03c6720>] netlink_unicast+0x15c/0x228
       [<c03c6c7c>] netlink_sendmsg+0x218/0x298
       [<c03933c8>] sock_sendmsg+0xa4/0xc0
       [<c039406c>] __sys_sendmsg+0x1e4/0x268
       [<c0394228>] sys_sendmsg+0x4c/0x70
       [<c0013840>] ret_fast_syscall+0x0/0x3c

-> #1 (reg_mutex){+.+.+.}:
       [<c008fd44>] validate_chain+0xb94/0x10f0
       [<c0090b68>] __lock_acquire+0x8c8/0x9b0
       [<c0090d40>] lock_acquire+0xf0/0x114
       [<c04734dc>] mutex_lock_nested+0x48/0x320
       [<bf28b2cc>] reg_todo+0x30/0x538 [cfg80211]
       [<c0059f44>] process_one_work+0x2a0/0x480
       [<c005a4b4>] worker_thread+0x1bc/0x2bc
       [<c0061148>] kthread+0x98/0xa4
       [<c0014af4>] kernel_thread_exit+0x0/0x8

-> #0 (cfg80211_mutex){+.+.+.}:
       [<c008ed58>] print_circular_bug+0x68/0x2cc
       [<c008fb28>] validate_chain+0x978/0x10f0
       [<c0090b68>] __lock_acquire+0x8c8/0x9b0
       [<c0090d40>] lock_acquire+0xf0/0x114
       [<c04734dc>] mutex_lock_nested+0x48/0x320
       [<bf28ae00>] restore_regulatory_settings+0x34/0x418 [cfg80211]
       [<bf28b200>] reg_timeout_work+0x1c/0x20 [cfg80211]
       [<c0059f44>] process_one_work+0x2a0/0x480
       [<c005a4b4>] worker_thread+0x1bc/0x2bc
       [<c0061148>] kthread+0x98/0xa4
       [<c0014af4>] kernel_thread_exit+0x0/0x8

other info that might help us debug this:

Chain exists of:
  cfg80211_mutex --> reg_mutex --> (reg_timeout).work

Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock((reg_timeout).work);
                               lock(reg_mutex);
                               lock((reg_timeout).work);
  lock(cfg80211_mutex);

*** DEADLOCK ***

2 locks held by kworker/0:2/1391:
#0:  (events){.+.+.+}, at: [<c0059e94>] process_one_work+0x1f0/0x480
#1:  ((reg_timeout).work){+.+...}, at: [<c0059e94>] process_one_work+0x1f0/0x480

stack backtrace:
[<c001b928>] (unwind_backtrace+0x0/0x12c) from [<c0471d3c>] (dump_stack+0x20/0x24)
[<c0471d3c>] (dump_stack+0x20/0x24) from [<c008ef70>] (print_circular_bug+0x280/0x2cc)
[<c008ef70>] (print_circular_bug+0x280/0x2cc) from [<c008fb28>] (validate_chain+0x978/0x10f0)
[<c008fb28>] (validate_chain+0x978/0x10f0) from [<c0090b68>] (__lock_acquire+0x8c8/0x9b0)
[<c0090b68>] (__lock_acquire+0x8c8/0x9b0) from [<c0090d40>] (lock_acquire+0xf0/0x114)
[<c0090d40>] (lock_acquire+0xf0/0x114) from [<c04734dc>] (mutex_lock_nested+0x48/0x320)
[<c04734dc>] (mutex_lock_nested+0x48/0x320) from [<bf28ae00>] (restore_regulatory_settings+0x34/0x418 [cfg80211])
[<bf28ae00>] (restore_regulatory_settings+0x34/0x418 [cfg80211]) from [<bf28b200>] (reg_timeout_work+0x1c/0x20 [cfg80211])
[<bf28b200>] (reg_timeout_work+0x1c/0x20 [cfg80211]) from [<c0059f44>] (process_one_work+0x2a0/0x480)
[<c0059f44>] (process_one_work+0x2a0/0x480) from [<c005a4b4>] (worker_thread+0x1bc/0x2bc)
[<c005a4b4>] (worker_thread+0x1bc/0x2bc) from [<c0061148>] (kthread+0x98/0xa4)
[<c0061148>] (kthread+0x98/0xa4) from [<c0014af4>] (kernel_thread_exit+0x0/0x8)
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

Cc: stable@kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mwifiex: fix incorrect privacy setting in beacon and probe response

Test procedure:
1. Start AP with security setting (e.g. WPA2)
2. Stop AP
3. Start AP with open security

Here it's observed that privacy is enabled in beacons and
probe responses.

This patch fixes it by checking the privacy parameter from
cfg80211_ap_settings. If privacy is not set in cfg80211_ap_settings,
set open authentication and no encryption in FW.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add missing kernel-doc

Add a few kernel-doc descriptions that were missed
during mesh development.

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth

rndis_wlan: fix matching bssid check in rndis_check_bssid_list()

rndis_check_bssid_list() originally tried to check if bssid->mac and
match_bssid are equal using compare_ether_addr() when it should use
!compare_ether_addr(). This check was added by commit
b5257c952dda24df7078c74b7b811b44c6e49206 as part of workaround for
hardware issue.

Commit 2e42e4747ea72943c21551d8a206b51a9893b1e0 that replaced
compare_ether_addr with ether_addr_equal relieved that this compare
to be inverse of what it should be.

Compare was added as response to hardware bug, where bssid-list does
not contain BSSID and other information of currently connected AP
(spec insists that device must provide this information in the list
when connected). Lack bssid-data on current connection then causes
WARN_ON somewhere in cfg80211. Workaround was to check if bssid-list
returns current bssid and if it does not, manually construct bssid
information in other ways. And this workaround worked, with inverse
check. Which must mean that when hardware is experiencing the problem,
it's actually returning empty bssid-list and this check didn't make
any difference for workaround.

However inverse check causes workaround be activated when bssid-list
returns only entry, currently connected BSSID. That does not cause
problems in itself, just slightly more inaccurate information in
scan-list.

Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove incompatible IBSS interface check in change_iface

'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.

this patch is dependent on 'cfg80211: fix interface combinations'

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix a WARNING on suspend/resume with IBSS

this patch is dependent on the patch "cfg80211: fix interface
combinations"

In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC.  we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.

The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.

        ath: phy0: Cannot create ADHOC interface when other
        interfaces already exist.
        WARNING: at net/mac80211/driver-ops.h:12
        ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
        Hardware name: 2842RK1
        wlan2:  Failed check-sdata-in-driver check, flags: 0x0

        Call Trace:
        [<c01361b2>] warn_slowpath_common+0x72/0xa0
        [<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
        [mac80211]
        [<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
        [mac80211]
        [<c0136283>] warn_slowpath_fmt+0x33/0x40
        [<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
        [<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
        [<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
        [<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]

Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: check iface combinations only when iface is running

Don't validate interface combinations on a stopped
interface. Otherwise we might end up being able to
create a new interface with a certain type, but
won't be able to change an existing interface
into that type.

This also skips some other functions when
interface is stopped and changing interface type.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: add some missing kernel-doc

Add a few kernel-doc descriptions that were missed
during development.

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Bluetooth: Add support for encryption key refresh

With LE/SMP the completion of a security level elavation from medium to
high is indicated by a HCI Encryption Key Refresh Complete event. The
necessary behavior upon receiving this event is a mix of what's done for
auth_complete and encryption_change, which is also where most of the
event handling code has been copied from.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

mac80211: add back channel change flag

commit 24398e39c8ee4a9d9123eed322b859ece4d16cac
Author: Johannes Berg <johannes.berg@intel.com>
Date: Wed Mar 28 10:58:36 2012 +0200

mac80211: set HT channel before association

removed IEEE80211_CONF_CHANGE_CHANNEL argument from ieee80211_hw_config,
which is required by iwl4965 driver, otherwise that driver does not
configure channel properly and is not able to associate.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Fix possible NULL ptr deref when getting the name of a socket

llcp_sock_getname() might get called before the LLCP socket was created.
This condition isn't checked, and llcp_sock_getname will simply deref a
NULL ptr in that case.

This exists starting with d646960 ("NFC: Initial LLCP support").

Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: disable the buggy chain extension feature in HW

This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.

Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: don't mess up the SCD when removing a key

When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.

This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:

Queue 2 stuck for 10000ms

This doesn't seem to fix the higher queues that get stuck
from time to time.

Cc: stable@vger.kernel.org [2.6.27+]
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: fix null pointer in bcma_core_pci_irq_ctl

pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: do not call ieee80211_unregister_hw if we are not registred

this patch fixes kernel Oops on "rmmod b43" if firmware was not loaded:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff8104e988>] drain_workqueue+0x25/0x142
PGD 153ac6067 PUD 153b82067 PMD 0
Oops: 0000 [#1] SMP

Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use correct supported firmware for 6035 and 6000g2

My patch

iwlwifi: use correct released ucode version

did not correctly report supported firmware
for the 6035 device. This patch fixes it. The
minimum supported firmware version for 6035
is v6.

Also correct the minimum supported firmware
version for the 6000g2 series of devices.

Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: add my new trees to MAINTAINERS

Add my new trees to the MAINTAINERS file
for the components that I maintain in the
new trees.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: Set IEEE80211_STAT_ACK flag when userspace indicates that the frame has been acknowledged.

The station fail average is not updated correctly since the
IEEE80211_STAT_ACK flag is not set when using wmediumd with
mac80211_hwsim. Set this flag when wmediumd indicates that the frame
was successfully transmitted (eventually).

Signed-off-by: Qasim Javed <qasimj@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8187: ->brightness_set can not sleep

Fix:

BUG: sleeping function called from invalid context at kernel/workqueue.c:2547
in_atomic(): 1, irqs_disabled(): 0, pid: 629, name: wpa_supplicant
2 locks held by wpa_supplicant/629:
#0: (rtnl_mutex){+.+.+.}, at: [<c08b2b84>] rtnl_lock+0x14/0x20
#1: (&trigger->leddev_list_lock){.+.?..}, at: [<c0867f41>] led_trigger_event+0x21/0x80
Pid: 629, comm: wpa_supplicant Not tainted 3.3.0-0.rc3.git5.1.fc17.i686
Call Trace:
[<c046a9f6>] __might_sleep+0x126/0x1d0
[<c0457d6c>] wait_on_work+0x2c/0x1d0
[<c045a09a>] __cancel_work_timer+0x6a/0x120
[<c045a160>] cancel_delayed_work_sync+0x10/0x20
[<f7dd3c22>] rtl8187_led_brightness_set+0x82/0xf0 [rtl8187]
[<c0867f7c>] led_trigger_event+0x5c/0x80
[<f7ff5e6d>] ieee80211_led_radio+0x1d/0x40 [mac80211]
[<f7ff3583>] ieee80211_stop_device+0x13/0x230 [mac80211]

Removing _sync is ok, because if led_on work is currently running
it will be finished before led_off work start to perform, since
they are always queued on the same mac80211 local->workqueue.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=795176

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/wireless: ipw2100: Fix WARN_ON occurring in wiphy_register called by ipw2100_pci_init_one

The problem was found by Larry Finger:
http://marc.info/?l=linux-wireless&m=133702401700614&w=2

The problem is identical to the one for ipw2200 which is already fixed:
http://marc.info/?l=linux-wireless&m=133457257407196&w=2

[   17.766431] ------------[ cut here ]------------
[   17.766467] WARNING: at net/wireless/core.c:562 wiphy_register+0x34c/0x3c0 [cfg80211]()
[   17.766471] Hardware name: Latitude D600
[   17.766474] Modules linked in: ipw2100(+) libipw pcmcia cfg80211 ppdev parport_pc yenta_socket sr_mod pcmcia_rsrc parport iTCO_wdt cdrom sg rfkill pcmcia_
core lib80211 tg3 video button battery ac iTCO_vendor_support joydev shpchp pcspkr pciehp pci_hotplug autofs4 radeon ttm drm_kms_helper uhci_hcd ehci_hcd rtc
_cmos thermal drm hwmon i2c_algo_bit i2c_core processor usbcore usb_common ata_generic ata_piix ahci libahci libata
[   17.766525] Pid: 474, comm: modprobe Not tainted 3.4.0-rc7-wl+ #6
[   17.766528] Call Trace:
[   17.766541]  [<c066ad08>] ? printk+0x28/0x2a
[   17.766552]  [<c0230edd>] warn_slowpath_common+0x6d/0xa0
[   17.766563]  [<e0b253bc>] ? wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766573]  [<e0b253bc>] ? wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766578]  [<c0230f2d>] warn_slowpath_null+0x1d/0x20
[   17.766588]  [<e0b253bc>] wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766605]  [<e0b5b0d6>] ipw2100_wdev_init+0x196/0x1c0 [ipw2100]
[   17.766616]  [<e0b5d962>] ipw2100_pci_init_one+0x2b2/0x694 [ipw2100]
[   17.766632]  [<c047ce52>] local_pci_probe+0x42/0xb0
[   17.766637]  [<c047e2b0>] pci_device_probe+0x60/0x90
[   17.766645]  [<c0376de2>] ? sysfs_create_link+0x12/0x20
[   17.766654]  [<c050f1f6>] really_probe+0x56/0x2e0
[   17.766659]  [<c037636d>] ? create_dir+0x5d/0xa0
[   17.766667]  [<c0518c6b>] ? pm_runtime_barrier+0x3b/0xa0
[   17.766672]  [<c050f5e4>] driver_probe_device+0x44/0xa0
[   17.766677]  [<c047e227>] ? pci_match_device+0x97/0xa0
[   17.766681]  [<c050f6c9>] __driver_attach+0x89/0x90
[   17.766686]  [<c050f640>] ? driver_probe_device+0xa0/0xa0
[   17.766691]  [<c050da2a>] bus_for_each_dev+0x3a/0x70
[   17.766695]  [<c050ee6c>] driver_attach+0x1c/0x30
[   17.766699]  [<c050f640>] ? driver_probe_device+0xa0/0xa0
[   17.766704]  [<c050ea77>] bus_add_driver+0x187/0x280
[   17.766710]  [<c045b9cd>] ? kset_find_obj+0x2d/0x60
[   17.766715]  [<c047e2e0>] ? pci_device_probe+0x90/0x90
[   17.766719]  [<c047e2e0>] ? pci_device_probe+0x90/0x90
[   17.766724]  [<c050fb85>] driver_register+0x65/0x110
[   17.766729]  [<c047e09d>] __pci_register_driver+0x3d/0xa0
[   17.766738]  [<e09f705c>] ipw2100_init+0x5c/0x1000 [ipw2100]
[   17.766743]  [<c020110f>] do_one_initcall+0x2f/0x170
[   17.766749]  [<e09f7000>] ? 0xe09f6fff
[   17.766757]  [<c0287ce8>] sys_init_module+0xa8/0x210
[   17.766766]  [<c067a075>] syscall_call+0x7/0xb
[   17.766769] ---[ end trace 559898c6bb0d1c75 ]---
[   17.767093] ipw2100: probe of 0000:02:03.0 failed with error -5

This warning appears only if we apply Ben Hutchings' fix
http://marc.info/?l=linux-wireless&m=132720204412667&w=2
for the bug reported by Cesare Leonardi
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=656813
with cfg80211 warning during device registration
("cfg80211: failed to add phy80211 symlink to netdev!").

We separate device bring up and registration with network stack
to avoid the problem.

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Fix SMP security elevation from medium to high

If we have an unauthenticated key it is not sufficient to acheive high
security. Therefore, when deciding whether to encrypt the link or
request pairing, it is essential to in addition to checking the
existence of a key to also check whether it is authenticated or not.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix deadlock and crash when SMP pairing times out

The l2cap_conn_del function tries to cancel_sync the security timer, but
when it's called from the timeout function itself a deadlock occurs.
Subsequently the "hcon->l2cap_data = NULL" that's supposed to protect
multiple calls to l2cap_conn_del never gets cleared and when the
connection finally drops we double free's etc which will crash the
kernel.

This patch fixes the issue by using the HCI_CONN_LE_SMP_PEND for
protecting against this. The same flag is also used for the same purpose
in other places in the SMP code.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix LE pairing completion on connection failure

For BR/EDR pairing is assumed to be finished when connection is
done. For LE if connection is successful it did not necessarily
mean that pairing is also done but if the connection is unsuccessful
it should be assumed that pairing procedure is also finished.
This patch registers a new function with connect_cfm_cb callback for
LE link which sends the pairing complete signal to user space if
connection is unsuccessful.

Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix SMP pairing method selection

The tk_request function takes the local IO capability as the second last
parameter and the remote IO capability as the last parameter. They were
previously swapped: when we receive a pairing response
req->io_capability contains the local one and rsp->io_capability the
remote one.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Merge branch 'master' of git://git./linux/kernel/git/bluetooth/bluetooth

cfg80211: fix interface combinations check

If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.

Cc: stable@kernel.org
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: unregister LEDs if mac80211 registration fails

Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.

Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix double free/complete in firmware loading

Linus reported that due to mac80211 failing to register
the device (due to WoWLAN) his machine crashed etc. as
we double-freed the vmalloc() firmware area. His patch
to fix it was very similar to this one but I noticed
that there's another bug in the area: we complete the
completion before starting, so since we're running in
a work struct context stop() could be called while in
the middle of start() which will almost certainly lead
to issues.

Make a modification similar to his to avoid the double-
free but also move the completion to another spot so it
is only done after start() either finished or failed so
that stop() can have a consistent state.

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Fix checking the wrong flag when accepting a socket

Most probably a typo, the check should have been for BT_SK_DEFER_SETUP
instead of BT_DEFER_SETUP (which right now only represents a socket
option).

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

iwlwifi: disable WoWLAN if !CONFIG_PM_SLEEP

If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.

Cc: stable@kernel.org
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix non RCU-safe sta_list manipulation

sta_info_cleanup locks the sta_list using rcu_read_lock however
the delete operation isn't rcu safe. A race between sta_info_cleanup
timer being called and a STA being removed can occur which leads
to a panic while traversing sta_list. Fix this by switching to the
RCU-safe versions.

Cc: stable@vger.kernel.org
Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add ext PA workaround for BCM4331 and BCM43431

MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.

BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: use atomic variable for seqno

Remove spinlock as atomic_t can be used instead. Note we use only 16
lower bits, upper bits are changed but we impilcilty cast to u16.

This fix possible deadlock on IBSS mode reproted by lockdep:

=================================
[ INFO: inconsistent lock state ]
3.4.0-wl+ #4 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/u:2/30374 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&intf->seqlock)->rlock){+.?...}, at: [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
{IN-SOFTIRQ-W} state was registered at:
  [<c04978ab>] __lock_acquire+0x47b/0x1050
  [<c0498504>] lock_acquire+0x84/0xf0
  [<c0835733>] _raw_spin_lock+0x33/0x40
  [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
  [<f9979f2a>] rt2x00queue_write_tx_frame+0x1a/0x300 [rt2x00lib]
  [<f997834f>] rt2x00mac_tx+0x7f/0x380 [rt2x00lib]
  [<f98fe363>] __ieee80211_tx+0x1b3/0x300 [mac80211]
  [<f98ffdf5>] ieee80211_tx+0x105/0x130 [mac80211]
  [<f99000dd>] ieee80211_xmit+0xad/0x100 [mac80211]
  [<f9900519>] ieee80211_subif_start_xmit+0x2d9/0x930 [mac80211]
  [<c0782e87>] dev_hard_start_xmit+0x307/0x660
  [<c079bb71>] sch_direct_xmit+0xa1/0x1e0
  [<c0784bb3>] dev_queue_xmit+0x183/0x730
  [<c078c27a>] neigh_resolve_output+0xfa/0x1e0
  [<c07b436a>] ip_finish_output+0x24a/0x460
  [<c07b4897>] ip_output+0xb7/0x100
  [<c07b2d60>] ip_local_out+0x20/0x60
  [<c07e01ff>] igmpv3_sendpack+0x4f/0x60
  [<c07e108f>] igmp_ifc_timer_expire+0x29f/0x330
  [<c04520fc>] run_timer_softirq+0x15c/0x2f0
  [<c0449e3e>] __do_softirq+0xae/0x1e0
irq event stamp: 18380437
hardirqs last  enabled at (18380437): [<c0526027>] __slab_alloc.clone.3+0x67/0x5f0
hardirqs last disabled at (18380436): [<c0525ff3>] __slab_alloc.clone.3+0x33/0x5f0
softirqs last  enabled at (18377616): [<c0449eb3>] __do_softirq+0x123/0x1e0
softirqs last disabled at (18377611): [<c041278d>] do_softirq+0x9d/0xe0

other info that might help us debug this:
Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&intf->seqlock)->rlock);
  <Interrupt>
    lock(&(&intf->seqlock)->rlock);

*** DEADLOCK ***

4 locks held by kworker/u:2/30374:
#0:  (wiphy_name(local->hw.wiphy)){++++.+}, at: [<c045cf99>] process_one_work+0x109/0x3f0
#1:  ((&sdata->work)){+.+.+.}, at: [<c045cf99>] process_one_work+0x109/0x3f0
#2:  (&ifibss->mtx){+.+.+.}, at: [<f98f005b>] ieee80211_ibss_work+0x1b/0x470 [mac80211]
#3:  (&intf->beacon_skb_mutex){+.+...}, at: [<f997a644>] rt2x00queue_update_beacon+0x24/0x50 [rt2x00lib]

stack backtrace:
Pid: 30374, comm: kworker/u:2 Not tainted 3.4.0-wl+ #4
Call Trace:
[<c04962a6>] print_usage_bug+0x1f6/0x220
[<c0496a12>] mark_lock+0x2c2/0x300
[<c0495ff0>] ? check_usage_forwards+0xc0/0xc0
[<c04978ec>] __lock_acquire+0x4bc/0x1050
[<c0527890>] ? __kmalloc_track_caller+0x1c0/0x1d0
[<c0777fb6>] ? copy_skb_header+0x26/0x90
[<c0498504>] lock_acquire+0x84/0xf0
[<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<c0835733>] _raw_spin_lock+0x33/0x40
[<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f997a5cf>] rt2x00queue_update_beacon_locked+0x5f/0xb0 [rt2x00lib]
[<f997a64d>] rt2x00queue_update_beacon+0x2d/0x50 [rt2x00lib]
[<f9977e3a>] rt2x00mac_bss_info_changed+0x1ca/0x200 [rt2x00lib]
[<f9977c70>] ? rt2x00mac_remove_interface+0x70/0x70 [rt2x00lib]
[<f98e4dd0>] ieee80211_bss_info_change_notify+0xe0/0x1d0 [mac80211]
[<f98ef7b8>] __ieee80211_sta_join_ibss+0x3b8/0x610 [mac80211]
[<c0496ab4>] ? mark_held_locks+0x64/0xc0
[<c0440012>] ? virt_efi_query_capsule_caps+0x12/0x50
[<f98efb09>] ieee80211_sta_join_ibss+0xf9/0x140 [mac80211]
[<f98f0456>] ieee80211_ibss_work+0x416/0x470 [mac80211]
[<c0496d8b>] ? trace_hardirqs_on+0xb/0x10
[<c077683b>] ? skb_dequeue+0x4b/0x70
[<f98f207f>] ieee80211_iface_work+0x13f/0x230 [mac80211]
[<c045cf99>] ? process_one_work+0x109/0x3f0
[<c045d015>] process_one_work+0x185/0x3f0
[<c045cf99>] ? process_one_work+0x109/0x3f0
[<f98f1f40>] ? ieee80211_teardown_sdata+0xa0/0xa0 [mac80211]
[<c045ed86>] worker_thread+0x116/0x270
[<c045ec70>] ? manage_workers+0x1e0/0x1e0
[<c0462f64>] kthread+0x84/0x90
[<c0462ee0>] ? __init_kthread_worker+0x60/0x60
[<c083d382>] kernel_thread_helper+0x6/0x10

Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Fix likely misuse of | for &

Using | with a constant is always true.
Likely this should have be &.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix likely misuse of | for &

Using | with a constant is always true.
Likely this should have be &.

cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add missing rcu_read_lock/unlock in agg-rx session timer

Fixes a lockdep warning:

===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
net/mac80211/agg-rx.c:148 invoked rcu_dereference_check() without protection!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 1
1 lock held by arecord/11226:
#0:  (&tid_agg_rx->session_timer){+.-...}, at: [<ffffffff81066bb0>] call_timer_fn+0x0/0x360

stack backtrace:
Pid: 11226, comm: arecord Not tainted 3.1.0-kml #16
Call Trace:
<IRQ>  [<ffffffff81093454>] lockdep_rcu_dereference+0xa4/0xc0
[<ffffffffa02778c9>] sta_rx_agg_session_timer_expired+0xc9/0x110 [mac80211]
[<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211]
[<ffffffff81066c3a>] call_timer_fn+0x8a/0x360
[<ffffffff81066bb0>] ? init_timer_deferrable_key+0x30/0x30
[<ffffffff81477bb0>] ? _raw_spin_unlock_irq+0x30/0x70
[<ffffffff81067049>] run_timer_softirq+0x139/0x310
[<ffffffff81091d5e>] ? put_lock_stats.isra.25+0xe/0x40
[<ffffffff810922ac>] ? lock_release_holdtime.part.26+0xdc/0x160
[<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211]
[<ffffffff8105cb78>] __do_softirq+0xc8/0x3c0
[<ffffffff8108f088>] ? tick_dev_program_event+0x48/0x110
[<ffffffff8108f16f>] ? tick_program_event+0x1f/0x30
[<ffffffff81153b15>] ? putname+0x35/0x50
[<ffffffff8147a43c>] call_softirq+0x1c/0x30
[<ffffffff81004c55>] do_softirq+0xa5/0xe0
[<ffffffff8105d1ee>] irq_exit+0xae/0xe0
[<ffffffff8147ac6b>] smp_apic_timer_interrupt+0x6b/0x98
[<ffffffff81479ab3>] apic_timer_interrupt+0x73/0x80
<EOI>  [<ffffffff8146aac6>] ? free_debug_processing+0x1a1/0x1d5
[<ffffffff81153b15>] ? putname+0x35/0x50
[<ffffffff8146ab2b>] __slab_free+0x31/0x2ca
[<ffffffff81477c3a>] ? _raw_spin_unlock_irqrestore+0x4a/0x90
[<ffffffff81253b8f>] ? __debug_check_no_obj_freed+0x15f/0x210
[<ffffffff81097054>] ? lock_release_nested+0x84/0xc0
[<ffffffff8113ec55>] ? kmem_cache_free+0x105/0x250
[<ffffffff81153b15>] ? putname+0x35/0x50
[<ffffffff81153b15>] ? putname+0x35/0x50
[<ffffffff8113ed8f>] kmem_cache_free+0x23f/0x250
[<ffffffff81153b15>] putname+0x35/0x50
[<ffffffff81146d8d>] do_sys_open+0x16d/0x1d0
[<ffffffff81146e10>] sys_open+0x20/0x30
[<ffffffff81478f42>] system_call_fastpath+0x16/0x1b

Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up remain-on-channel on interface stop

When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.

It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.

Cc: stable@kernel.org
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: advertise interface combinations

Enforcing interface combinations broke uses of hwsim
with multiple virtual interfaces. Advertise that all
combinations are possible to fix this.

Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix error in station state transitions during reconfig

As part of hardware reconfig mac80211 tries
to restore the station state to its values
before the hardware reconfig, but it only
goes to the last-state - 1. Fix this
off-by-one error.

Cc: stable@kernel.org [3.4]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix TX power antenna access

Since my commit
iwlwifi: use valid TX/RX antenna from hw_params
the config values are pure overrides, not the
real values for all hardware. Therefore, the
EEPROM TX power reading code checks the wrong
values, it should check the hw_params values.

Cc: stable@kernel.org [3.4]
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix Unreachable Mesh Station Problem when joining to another MBSS

Mesh station that joins an MBSS is reachable using mesh portal with 6
address frame by mesh stations from another MBSS if these two different
MBSSes are bridged. However, if the mesh station later moves into the
same MBSS of those mesh stations, it is unreachable by mesh stations
in the MBSS due to the mpp_paths table is not deleted. A quick fix
is to perform mesh_path_lookup, if it is available for the target
destination, mpp_path_lookup is not performed. When the mesh station
moves back to its original MBSS, the mesh_paths will be deleted once
expired. So, it will be reachable using mpp_path_lookup again.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: use sme_state in ibss start/join path

CFG80211_DEV_WARN_ON() at "net/wireless/ibss.c line 63"
is unnecessarily triggered even after successful connection,
when cfg80211_ibss_joined() is called by driver inside
.join_ibss handler.

This patch fixes the problem by changing 'sme_state' in ibss path
and having WARN_ON() check for 'sme_state' similar to infra
association.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: support NL80211_HIDDEN_SSID_ZERO_LEN for uAP

mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: invalidate bss config before setting channel for uAP

Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: run scan after finish connection monitoring

commit 133d40f9a22bdfd2617a446f1e3209537c5415ec
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Wed Mar 28 16:01:19 2012 +0200

mac80211: do not scan and monitor connection in parallel

add bug, which make possible to start a scan and never finish it, so
make every new scanning request finish with -EBUSY error. This can
happen on code paths where we finish connection monitoring and clear
IEEE80211_STA_*_POLL flags, but do not check if scan was deferred.
This patch fixes those code paths.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Linux 3.5-rc1

Merge tag 'dm-3.5-changes-1' of git://git./linux/kernel/git/agk/linux-dm

Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
  and provide a simple reserve/release mechanism for userspace tools to
  access thin provisioning metadata while the pool is in use."

* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm thin: provide userspace access to pool metadata
  dm thin: use slab mempools
  dm mpath: allow ioctls to trigger pg init
  dm mpath: delay retry of bypassed pg
  dm mpath: reduce size of struct multipath

dm thin: provide userspace access to pool metadata

This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_.  This,
read-only snapshot can be accessed by userland, concurrently with the
live target.

Only one metadata snapshot can be held at a time.  The pool's status
line will give the block location for the current msnap.

Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:

    thin_dump -m <msnap root> <metadata dev>

Available here: https://github.com/jthornber/thin-provisioning-tools

Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:

     i) Incremental backups.

     By using metadata snapshots we can work out what blocks have
     changed over time.  Combined with data snapshots we can ensure
     the data doesn't change while we back it up.

     A short proof of concept script can be found here:

     https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb

     ii) Migration of thin devices from one pool to another.

     iii) Merging snapshots back into an external origin.

     iv) Asyncronous replication.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

dm thin: use slab mempools

Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

dm mpath: allow ioctls to trigger pg init

After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device.  Until this has happened, ioctls return -EAGAIN.

With this patch, new paths are made available in response to an ioctl
too.  The processing of the ioctl gets delayed until this has happened.

Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.

Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure.  Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands).  For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too.  It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

dm mpath: delay retry of bypassed pg

If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.

If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

dm mpath: reduce size of struct multipath

Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Merge git://git./linux/kernel/git/davem/net

Pull networking updates from David Miller:

1) Make syn floods consume significantly less resources by

    a) Not pre-COW'ing routing metrics for SYN/ACKs
    b) Mirroring the device queue mapping of the SYN for the SYN/ACK
       reply.

    Both from Eric Dumazet.

2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.

3) Validate the length requested when building a paged SKB for a
    socket, so we don't overrun the page vector accidently.  From Jason
    Wang.

4) When netlabel is disabled, we abort all IP option processing when we
    see a CIPSO option.  This isn't the right thing to do, we should
    simply skip over it and continue processing the remaining options
    (if any).  Fix from Paul Moore.

5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
    Apfelbaum.

6) 8139cp enables the receiver before the ring address is properly
    programmed, which potentially lets the device crap over random
    memory.  Fix from Jason Wang.

7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
    address reference in jumbo RX frame processing from Bruce Allan and
    Sebastian Andrzej Siewior, respectively.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  fec_mpc52xx: fix timestamp filtering
  mcs7830: Implement link state detection
  e1000e: fix Rapid Start Technology support for i217
  e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
  r8169: call netif_napi_del at errpaths and at driver unload
  tcp: reflect SYN queue_mapping into SYNACK packets
  tcp: do not create inetpeer on SYNACK message
  8139cp/8139too: terminate the eeprom access with the right opmode
  8139cp: set ring address before enabling receiver
  cipso: handle CIPSO options correctly when NetLabel is disabled
  net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
  bql: Avoid possible inconsistent calculation.
  bql: Avoid unneeded limit decrement.
  bql: Fix POSDIFF() to integer overflow aware.
  net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
  net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
  net/mlx4_core: Fixes for VF / Guest startup flow
  net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
  net/mlx4_core: Fix number of EQs used in ICM initialisation
  net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull straggler x86 fixes from Peter Anvin:
"Three groups of patches:

  - EFI boot stub documentation and the ability to print error messages;
  - Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
    should never have been ported, and the port is broken and
    potentially dangerous.)
  - ftrace stack corruption fixes.  I'm not super-happy about the
    technical implementation, but it is probably the least invasive in
    the short term.  In the future I would like a single method for
    nesting the debug stack, however."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
  x86, efi: Add EFI boot stub documentation
  x86, efi; Add EFI boot stub console support
  x86, efi: Only close open files in error path
  ftrace/x86: Do not change stacks in DEBUG when calling lockdep
  x86: Allow nesting of the debug stack IDT setting
  x86: Reset the debug_stack update counter
  ftrace: Use breakpoint method to update ftrace caller
  ftrace: Synchronize variable setting with breakpoints

tty: Revert the tty locking series, it needs more work

This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.

The main revert is d29f3ef39be4 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:

  fde86d310886 - tty: add lockdep annotations
  8f6576ad476b - tty: fix ldisc lock inversion trace
  d3ca8b64b97e - pty: Fix lock inversion
  b1d679afd766 - tty: drop the pty lock during hangup
  abcefe5fc357 - tty/amiserial: Add missing argument for tty_unlock()
  fd11b42e3598 - cris: fix missing tty arg in wait_event_interruptible_tty call
  d29f3ef39be4 - tty_lock: Localise the lock

The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fec_mpc52xx: fix timestamp filtering

skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.

Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mcs7830: Implement link state detection

Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge 'for-linus' branches from git://git./linux/kernel/git/viro/{vfs,signal}

Pull vfs fix and a fix from the signal changes for frv from Al Viro.

The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short".  Al didn't notice, and
made both of them be the unsigned short.

The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  powerpc: Fix size of st_nlink on 64bit

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  frv: Remove bogus closing parenthesis

powerpc: Fix size of st_nlink on 64bit

commit e57f93cc53b7 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

frv: Remove bogus closing parenthesis

Introduced by commit 6fd84c0831ec78d98736b76dc5e9b849f1dbfc9e
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

e1000e: fix Rapid Start Technology support for i217

The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.

Also for clarity, rename a few defines as bit definitions instead of masks.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()

This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge branch 'akpm' (Fixups for Andrew's patchbomb)

Merge fixups for the mac NLS tables from Andrew.

* emailed from Andrew Morton, and one cleanup by me:
nls: fix (and rename) mac NLS table files and config options
fs/nls/Makefile: remove bogus CONFIG_ assignments

nls: fix (and rename) mac NLS table files and config options

The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).

And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".

So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/nls/Makefile: remove bogus CONFIG_ assignments

These were debug things which snuck through.

Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6

Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups

* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
  video: bfin_adv7393fb: Fix cleanup code
  video: exynos_dp: reduce delay time when configuring video setting
  video: exynos_dp: move sw reset prioir to enabling sw defined function
  video: exynos_dp: use devm_ functions
  fb: handle NULL pointers in framebuffer release
  OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
  OMAPDSS: Apply VENC timings even if panel is disabled
  OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
  OMAPDSS: DISPC: Support rotation through TILER
  OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
  OMAPFB: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
  OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
  OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
  OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
  drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
  video: exynos mipi dsi: support reverse panel type
  video: exynos mipi dsi: Properly interpret the interrupt source flags
  video: exynos mipi dsi: Avoid races in probe()
  ...

Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd

Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs

Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.

* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
  mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
  mtd: block2mtd: fix recursive call of mtd_writev
  mtd: gpmi-nand: define ecc.strength
  mtd: of_parts: fix breakage in Kconfig
  mtd: nand: fix scan_read_raw_oob
  mtd: docg3 fix in-middle of blocks reads
  mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
  mtd: add fixup for S29NS512P NOR flash.
  jffs2: allow to complete xattr integrity check on first GC scan
  jffs2: allow to discriminate between recoverable and non-recoverable errors
  mtd: nand: omap: add support for hardware BCH ecc
  ARM: OMAP3: gpmc: add BCH ecc api and modes
  mtd: nand: check the return code of 'read_oob/read_oob_raw'
  mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
  mtd: m25p80: Add support for Winbond W25Q80BW
  jffs2: get rid of jffs2_sync_super
  jffs2: remove unnecessary GC pass on sync
  jffs2: remove unnecessary GC pass on umount
  jffs2: remove lock_super
  mtd: gpmi: add gpmi support for mx6q
  ...

Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86

Pull x86 platform driver updates from Matthew Garrett:
"Some significant improvements for the Sony driver on newer machines,
  but other than that mostly just minor fixes and a patch to remove the
  broken rfkill code from the Dell driver."

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (35 commits)
  apple-gmux: Fix up the suspend/resume patch
  dell-laptop: Remove rfkill code
  toshiba_acpi: Fix mis-merge
  dell-laptop: Add touchpad led support for Dell V3450
  acer-wmi: add 3 laptops to video backlight vendor mode quirk table
  sony-laptop: add touchpad enable/disable function
  sony-laptop: add missing Fn key combos for 0x100 handlers
  sony-laptop: add support for more WWAN modems
  sony-laptop: new keyboard backlight handle
  sony-laptop: add high speed battery charging function
  sony-laptop: support automatic resume on lid open
  sony-laptop: adjust error handling in finding SNC handles
  sony-laptop: add thermal profiles support
  sony-laptop: support battery care functions
  sony-laptop: additional debug statements
  sony-laptop: improve SNC initialization and acpi notify callback code
  sony-laptop: use kstrtoul to parse sysfs values
  sony-laptop: generalise ACPI calls into SNC functions
  sony-laptop: fix return path when no ACPI buffer is allocated
  sony-laptop: use soft rfkill status stored in hw
  ...

Merge branch 'slab/for-linus' of git://git./linux/kernel/git/penberg/linux

Pull slab updates from Pekka Enberg:
"Mainly a bunch of SLUB fixes from Joonsoo Kim"

* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slub: use __SetPageSlab function to set PG_slab flag
  slub: fix a memory leak in get_partial_node()
  slub: remove unused argument of init_kmem_cache_node()
  slub: fix a possible memory leak
  Documentations: Fix slabinfo.c directory in vm/slub.txt
  slub: fix incorrect return type of get_any_partial()

Merge remote-tracking branch 'rostedt/tip/perf/urgent-2' into x86-urgent-for-linus

Merge branch 'ux500/hickup' of git://git./linux/kernel/git/arm/arm-soc

Pull arm fixes for ux500 mismerge mishap from Arnd Bergmann:
"The device tree conversion for arm/ux500 in 3.5 turns out to be
  incomplete because of a mismerge done by Linus Walleij that I failed
  to notice early enough and that Lee Jones as the original author of
  those patches did not manage to fix during the -next cycle.  While we
  originally to get a much larger set of ux500 device tree enablement
  patches merged, this did not happen in time.

  After some discussion at Linaro Connect conference this week, Lee has
  been able to do damage control and provide a series to put the broken
  platform back into usable shape for both DT and non-DT based booting.

  This series has not been part of linux-next and is based on top of the
  current state of the upstream kernel rather than an -rc, but this is
  the best we could manage given the earlier breakage."

* 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: ux500: Enable probing of pinctrl through Device Tree
  ARM: ux500: Add support for ab8500 regulators into the Device Tree
  ARM: ux500: Provide regulator support for SMSC911x via Device Tree
  ARM: ux500: Allow PRCMU regulator to be probed during a DT enabled boot
  ARM: ux500: Apply db8500-prcmu regulator information to db8500 Device Tree
  ARM: ux500: Only initialise STE's UIBs on boards which support them
  ARM: ux500: Disable platform setup of the ab8500 when DT is enabled
  ARM: ux500: Use correct format for dynamic IRQ assignment
  ARM: ux500: Re-enable SMSC911x platform code registration during non-DT boots
  ARM: ux500: PRCMU related configuration and layout corrections for Device Tree
  ARM: ux500: Remove DB8500 PRCMU platform registration when DT is enabled
  ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
  ARM: ux500: New DT:ed u8500_init_devices for one-by-one device enablement
  ARM: ux500: New DT:ed snowball_platform_devs for one-by-one device enablement
  pinctrl-nomadik: Allow Device Tree driver probing

r8169: call netif_napi_del at errpaths and at driver unload

when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.

Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
"A bunch of fixes:
   - vmware memory corruption
   - ttm spinlock balance
   - cirrus/mgag200 work in the presence of efifb
  and finally Alex and Jerome managed to track down a magic set of bits
  that on certain rv740 and evergreen cards allow the correct use of the
  complete set of render backends, this makes the cards operate
  correctly in a number of scenarios we had issues in before, it also
  manages to boost speed on benchmarks my large amounts on these
  specific gpus."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/edid: Make the header fixup threshold tunable
  drm/radeon: fix regression in UMS CS ioctl
  drm/vmwgfx: Fix nasty write past alloced memory area
  drm/ttm: Fix spinlock imbalance
  drm/radeon: fixup tiling group size and backendmap on r6xx-r9xx (v4)
  drm/radeon: fix HD6790, HD6570 backend programming
  drm/radeon: properly program gart on rv740, juniper, cypress, barts, hemlock
  drm/radeon: fix bank information in tiling config
  drm/mgag200: kick off conflicting framebuffers earlier.
  drm/cirrus: kick out conflicting framebuffers earlier
  cirrus: avoid crash if driver fails to load

Merge tag 'sound-3.5' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"Just a few trivial driver-specific fixes."

* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hdspm - Work around broken DDS value on PCI RME MADI
  ALSA: usb-audio: fix rate_list memory leak
  ASoC: fsi: bugfix: ensure dma is terminated
  ASoC: fsi: bugfix: correct dma area
  ASoC: fsi: bugfix: enable master clock control on DMA stream
  ASoC: imx-ssi: Use clk_prepare_enable/clk_disable_unprepare

x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32

When I added x32 ptrace to 3.4 kernel, I also include PTRACE_ARCH_PRCTL
support for x32 GDB  For ARCH_GET_FS/GS, it takes a pointer to int64.  But
at user level, ARCH_GET_FS/GS takes a pointer to int32.  So I have to add
x32 ptrace to glibc to handle it with a temporary int64 passed to kernel and
copy it back to GDB as int32.  Roland suggested that PTRACE_ARCH_PRCTL
is obsolete and x32 GDB should use fs_base and gs_base fields of
user_regs_struct instead.

Accordingly, remove PTRACE_ARCH_PRCTL completely from the x32 code to
avoid possible memory overrun when pointer to int32 is passed to
kernel.

Link: http://lkml.kernel.org/r/CAMe9rOpDzHfS7NH7m1vmD9QRw8SSj4Sc%2BaNOgcWm_WJME2eRsQ@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org> v3.4

mtd: mxc_nand: move ecc strengh setup before nand_scan_tail

Since commit 6a918bade9dab40aaef80559bd1169c69e8d69cb, the mxc_nand driver
fails with:

Driver must set ecc.strength when using hardware ECC

This is because nand_scan_tail checks for correct ecc strength
settings, so we must set them up before nand_scan_tail.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org [3.4+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

mtd: block2mtd: fix recursive call of mtd_writev

The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.

This is caused by 1dbebd32562b3c2caeca35960e5cb00bfcc12900
(mtd: harmonize mtd_writev usage).

Remove the assignment from the block2mtd driver to fix the
issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

mtd: gpmi-nand: define ecc.strength

Fix an issue which was introduced by the recent addition of ecc.strength.

The ecc.strength wasn't set in gpmi-nand, resulting in the following crash:
[    2.550000] kernel BUG at drivers/mtd/nand/nand_base.c:3347!
...
[    2.550000] [<c020841c>] (nand_scan_tail+0x328/0x650) from [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4)
[    2.550000] [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4) from [<c01f6618>] (platform_drv_probe+0x14/0x18)
[    2.550000] [<c01f6618>] (platform_drv_probe+0x14/0x18) from [<c01f55b0>] (driver_probe_device+0x74/0x1fc)
[    2.550000] [<c01f55b0>] (driver_probe_device+0x74/0x1fc) from [<c01f57cc>] (__driver_attach+0x94/0x98)
[    2.550000] [<c01f57cc>] (__driver_attach+0x94/0x98) from [<c01f3d40>] (bus_for_each_dev+0x50/0x80)
[    2.550000] [<c01f3d40>] (bus_for_each_dev+0x50/0x80) from [<c01f4e18>] (bus_add_driver+0x188/0x25c)
[    2.550000] [<c01f4e18>] (bus_add_driver+0x188/0x25c) from [<c01f5a70>] (driver_register+0x78/0x138)
[    2.550000] [<c01f5a70>] (driver_register+0x78/0x138) from [<c043dc7c>] (gpmi_nand_init+0xc/0x30)
[    2.550000] [<c043dc7c>] (gpmi_nand_init+0xc/0x30) from [<c0008824>] (do_one_initcall+0x108/0x17c)
[    2.550000] [<c0008824>] (do_one_initcall+0x108/0x17c) from [<c042a8b8>] (kernel_init+0xfc/0x1bc)
[    2.550000] [<c042a8b8>] (kernel_init+0xfc/0x1bc) from [<c000fab4>] (kernel_thread_exit+0x0/0x8)

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

apple-gmux: Fix up the suspend/resume patch

I incorporated the wrong version of the suspend/resume patch for gmux,
and so lost David Woodhouse's fix to leave the backlight level unchanged
over suspend/resume. This fixes it up to v2.

Signed-off-by: Matthew Garrett <mjg@redhat.com>

mtd: of_parts: fix breakage in Kconfig

MTD_OF_PARTS and the default setting is not working due to using 'Y'
instead of 'y', introduced in commit
d6137badeff1ef64b4e0092ec249ebdeaeb3ff37. This made our board, and
possibly other boards using DTS defined partitions and not having
CONFIG_MTD_OF_PARTS=y defined in the defconfig, fail to mount root.

Signed-off-by: Frank Svendsboe <frank.svendsboe@gmail.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/signal

Pull third pile of signal handling patches from Al Viro:
"This time it's mostly helpers and conversions to them; there's a lot
  of stuff remaining in the tree, but that'll either go in -rc2
  (isolated bug fixes, ideally via arch maintainers' trees) or will sit
  there until the next cycle."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  x86: get rid of calling do_notify_resume() when returning to kernel mode
  blackfin: check __get_user() return value
  whack-a-mole with TIF_FREEZE
  FRV: Optimise the system call exit path in entry.S [ver #2]
  FRV: Shrink TIF_WORK_MASK [ver #2]
  FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
  new helper: signal_delivered()
  powerpc: get rid of restore_sigmask()
  most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
  set_restore_sigmask() is never called without SIGPENDING (and never should be)
  TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
  don't call try_to_freeze() from do_signal()
  pull clearing RESTORE_SIGMASK into block_sigmask()
  sh64: failure to build sigframe != signal without handler
  openrisc: tracehook_signal_handler() is supposed to be called on success
  new helper: sigmask_to_save()
  new helper: restore_saved_sigmask()
  new helpers: {clear,test,test_and_clear}_restore_sigmask()
  HAVE_RESTORE_SIGMASK is defined on all architectures now

tcp: reflect SYN queue_mapping into SYNACK packets

While testing how linux behaves on SYNFLOOD attack on multiqueue device
(ixgbe), I found that SYNACK messages were dropped at Qdisc level
because we send them all on a single queue.

Obvious choice is to reflect incoming SYN packet @queue_mapping to
SYNACK packet.

Under stress, my machine could only send 25.000 SYNACK per second (for
200.000 incoming SYN per second). NIC : ixgbe with 16 rx/tx queues.

After patch, not a single SYNACK is dropped.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: do not create inetpeer on SYNACK message

Another problem on SYNFLOOD/DDOS attack is the inetpeer cache getting
larger and larger, using lots of memory and cpu time.

tcp_v4_send_synack()
->inet_csk_route_req()
->ip_route_output_flow()
  ->rt_set_nexthop()
   ->rt_init_metrics()
    ->inet_getpeer( create = true)

This is a side effect of commit a4daad6b09230 (net: Pre-COW metrics for
TCP) added in 2.6.39

Possible solution :

Instruct inet_csk_route_req() to remove FLOWI_FLAG_PRECOW_METRICS

Before patch :

# grep peer /proc/slabinfo
inet_peer_cache   4175430 4175430    192   42    2 : tunables    0    0    0 : slabdata  99415  99415      0

Samples: 41K of event 'cycles', Event count (approx.): 30716565122
+  20,24%      ksoftirqd/0  [kernel.kallsyms]           [k] inet_getpeer
+   8,19%      ksoftirqd/0  [kernel.kallsyms]           [k] peer_avl_rebalance.isra.1
+   4,81%      ksoftirqd/0  [kernel.kallsyms]           [k] sha_transform
+   3,64%      ksoftirqd/0  [kernel.kallsyms]           [k] fib_table_lookup
+   2,36%      ksoftirqd/0  [ixgbe]                     [k] ixgbe_poll
+   2,16%      ksoftirqd/0  [kernel.kallsyms]           [k] __ip_route_output_key
+   2,11%      ksoftirqd/0  [kernel.kallsyms]           [k] kernel_map_pages
+   2,11%      ksoftirqd/0  [kernel.kallsyms]           [k] ip_route_input_common
+   2,01%      ksoftirqd/0  [kernel.kallsyms]           [k] __inet_lookup_established
+   1,83%      ksoftirqd/0  [kernel.kallsyms]           [k] md5_transform
+   1,75%      ksoftirqd/0  [kernel.kallsyms]           [k] check_leaf.isra.9
+   1,49%      ksoftirqd/0  [kernel.kallsyms]           [k] ipt_do_table
+   1,46%      ksoftirqd/0  [kernel.kallsyms]           [k] hrtimer_interrupt
+   1,45%      ksoftirqd/0  [kernel.kallsyms]           [k] kmem_cache_alloc
+   1,29%      ksoftirqd/0  [kernel.kallsyms]           [k] inet_csk_search_req
+   1,29%      ksoftirqd/0  [kernel.kallsyms]           [k] __netif_receive_skb
+   1,16%      ksoftirqd/0  [kernel.kallsyms]           [k] copy_user_generic_string
+   1,15%      ksoftirqd/0  [kernel.kallsyms]           [k] kmem_cache_free
+   1,02%      ksoftirqd/0  [kernel.kallsyms]           [k] tcp_make_synack
+   0,93%      ksoftirqd/0  [kernel.kallsyms]           [k] _raw_spin_lock_bh
+   0,87%      ksoftirqd/0  [kernel.kallsyms]           [k] __call_rcu
+   0,84%      ksoftirqd/0  [kernel.kallsyms]           [k] rt_garbage_collect
+   0,84%      ksoftirqd/0  [kernel.kallsyms]           [k] fib_rules_lookup

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8139cp/8139too: terminate the eeprom access with the right opmode

Currently, we terminate the eeprom access through clearing the CS by:

RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);

This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.

Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8139cp: set ring address before enabling receiver

Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.

btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.

Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cipso: handle CIPSO options correctly when NetLabel is disabled

When NetLabel is not enabled, e.g. CONFIG_NETLABEL=n, and the system
receives a CIPSO tagged packet it is dropped (cipso_v4_validate()
returns non-zero). In most cases this is the correct and desired
behavior, however, in the case where we are simply forwarding the
traffic, e.g. acting as a network bridge, this becomes a problem.

This patch fixes the forwarding problem by providing the basic CIPSO
validation code directly in ip_options_compile() without the need for
the NetLabel or CIPSO code. The new validation code can not perform
any of the CIPSO option label/value verification that
cipso_v4_validate() does, but it can verify the basic CIPSO option
format.

The behavior when NetLabel is enabled is unchanged.

Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull vfs changes from Al Viro.
"A lot of misc stuff.  The obvious groups:
   * Miklos' atomic_open series; kills the damn abuse of
     ->d_revalidate() by NFS, which was the major stumbling block for
     all work in that area.
   * ripping security_file_mmap() and dealing with deadlocks in the
     area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
     general.
   * ->encode_fh() switched to saner API; insane fake dentry in
     mm/cleancache.c gone.
   * assorted annotations in fs (endianness, __user)
   * parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
   * ->update_time() work from Josef.
   * other bits and pieces all over the place.

  Normally it would've been in two or three pull requests, but
  signal.git stuff had eaten a lot of time during this cycle ;-/"

Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
  nfs: don't open in ->d_revalidate
  vfs: retry last component if opening stale dentry
  vfs: nameidata_to_filp(): don't throw away file on error
  vfs: nameidata_to_filp(): inline __dentry_open()
  vfs: do_dentry_open(): don't put filp
  vfs: split __dentry_open()
  vfs: do_last() common post lookup
  vfs: do_last(): add audit_inode before open
  vfs: do_last(): only return EISDIR for O_CREAT
  vfs: do_last(): check LOOKUP_DIRECTORY
  vfs: do_last(): make ENOENT exit RCU safe
  vfs: make follow_link check RCU safe
  vfs: do_last(): use inode variable
  vfs: do_last(): inline walk_component()
  vfs: do_last(): make exit RCU safe
  vfs: split do_lookup()
  Btrfs: move over to use ->update_time
  fs: introduce inode operation ->update_time
  reiserfs: get rid of resierfs_sync_super
  reiserfs: mark the superblock as dirty a bit later
  ...

Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4

Pull Ext4 updates from Theodore Ts'o:
"The major new feature added in this update is Darrick J Wong's
  metadata checksum feature, which adds crc32 checksums to ext4's
  metadata fields.

  There is also the usual set of cleanups and bug fixes."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (44 commits)
  ext4: hole-punch use truncate_pagecache_range
  jbd2: use kmem_cache_zalloc wrapper instead of flag
  ext4: remove mb_groups before tearing down the buddy_cache
  ext4: add ext4_mb_unload_buddy in the error path
  ext4: don't trash state flags in EXT4_IOC_SETFLAGS
  ext4: let getattr report the right blocks in delalloc+bigalloc
  ext4: add missing save_error_info() to ext4_error()
  ext4: add debugging trigger for ext4_error()
  ext4: protect group inode free counting with group lock
  ext4: use consistent ssize_t type in ext4_file_write()
  ext4: fix format flag in ext4_ext_binsearch_idx()
  ext4: cleanup in ext4_discard_allocated_blocks()
  ext4: return ENOMEM when mounts fail due to lack of memory
  ext4: remove redundundant "(char *) bh->b_data" casts
  ext4: disallow hard-linked directory in ext4_lookup
  ext4: fix potential integer overflow in alloc_flex_gd()
  ext4: remove needs_recovery in ext4_mb_init()
  ext4: force ro mount if ext4_setup_super() fails
  ext4: fix potential NULL dereference in ext4_free_inodes_counts()
  ext4/jbd2: add metadata checksumming to the list of supported features
  ...

x86: get rid of calling do_notify_resume() when returning to kernel mode

If we end up calling do_notify_resume() with !user_mode(refs), it
does nothing (do_signal() explicitly bails out and we can't get there
with TIF_NOTIFY_RESUME in such situations). Then we jump to
resume_userspace_sig, which rechecks the same thing and bails out
to resume_kernel, thus breaking the loop.

It's easier and cheaper to check *before* calling do_notify_resume()
and bail out to resume_kernel immediately. And kill the check in
do_signal()...

Note that on amd64 we can't get there with !user_mode() at all - asm
glue takes care of that.

Acked-and-reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

blackfin: check __get_user() return value

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>