selftests: add hugetlbfstest

As the confusing naming indicates, this test has some overlap with
pre-existing tests.  Would be nice to merge them eventually.  But since it
is only test code, cleanliness is much less important than mere existence.

Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

self-test: fix make clean

thuge-gen was forgotten.  Fix it by removing the duplication, so we don't
get too many repeats.

Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftests: exit 1 on failure

In case this ever gets scripted, it should return 0 on success and 1 on
failure.  Parsing the output should be left to meatbags.

Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/resource.c: remove the unneeded assignment in function __find_resource

This line was introduced by fcb11918 ("resources: add arch hook for
preventing allocation in reserved areas").  But the struct tmp was already
assigned to *new in the above line, so this seems superfluous.  Just
remove it.

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aio: fix wrong comment in aio_complete()

ctx->ctx_lock should be ctx->completion_lock.

Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode

Power-up timing

The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled.  When this occurs, the P0 port
does not respond to the Channel Access Write command.  For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below.  The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first.  This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.

Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD

[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/memstick/host/r592.c: convert to module_pci_driver

Signed-off-by: Libo Chen <libo.chen@huawei.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/memstick/host/jmb38x_ms: convert to module_pci_driver

Use module_pci_driver instead of init/exit, make code clean.

Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pps-gpio: add device-tree binding and support

Instead of allocating a struct pps_gpio_platform_data in the DT case,
store the necessary information in struct pps_gpio_device_data itself.
This avoids an additional allocation and the ifdef.  It also gets rid of
some indirection.

Also use dev_err instead of pr_err in the changed code.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/pps/clients/pps-gpio.c: convert to module_platform_driver

This removes some boilerplate code (no functional changes).

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/pps/clients/pps-gpio.c: convert to devm_* helpers

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/parport/share.c: use kzalloc

Replaced calls to kmalloc and memset with kzalloc.
Patch found using coccinelle.

Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/accounting/getdelays.c: avoid strncpy in accounting tool

Avoid strncpy anti-pattern.

[akpm@linux-foundation.org: remove the str[cpy|dup] altogether]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: update internal version number to v83

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: update copyright date

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aoe: perform I/O completions in parallel

Some users have a large AoE target while others like to use many AoE
targets at the same time.  In the latter case, there is an opportunity to
greatly improve aggregate throughput by allowing different threads to
complete the I/O associated with each target.  For 36 targets, 4 KiB read
throughput roughly doubles, for example, with these changes in place.

Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nbd: correct disconnect behavior

Currently, when a disconnect is requested by the user (via NBD_DISCONNECT
ioctl) the return from NBD_DO_IT is undefined (it is usually one of
several error codes).  This means that nbd-client does not know if a
manual disconnect was performed or whether a network error occurred.
Because of this, nbd-client's persist mode (which tries to reconnect after
error, but not after manual disconnect) does not always work correctly.

This change fixes this by causing NBD_DO_IT to always return 0 if a user
requests a disconnect.  This means that nbd-client can correctly either
persist the connection (if an error occurred) or disconnect (if the user
requested it).

Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Acked-by: Rob Landley <rob@landley.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nbd: remove bogus BUG_ON in NBD_CLEAR_QUE

The NBD_CLEAR_QUE ioctl has been deprecated for quite some time (its job
is now done by two other ioctls).  We should stop trying to make bogus
assertions in it.  Also, user-level code should remove calls to
NBD_CLEAR_QUE, ASAP.

Signed-off-by: Michal Belczyk <belczyk@bsd.krakow.pl>
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/pid.c: move statement

Move statement to static initilization of init_pid_ns.

Signed-off-by: Raphael S. Carvalho <raphael.scarv@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio: change endpoint device name format

Change endpoint device name format to use a component tag value instead of
device destination ID.

RapidIO specification defines a component tag to be a unique identifier
for devices in a network.  RapidIO switches already use component tag as
part of their device name and also use it for device identification when
processing error management event notifications.

Forming an endpoint's device name using its component tag instead of
destination ID allows to keep sysfs device directories unchanged in case
if a routing process dynamically changes endpoint's destination ID as a
result of route optimization.

This change should not affect any existing users because a valid device
destination ID always should be obtained by reading "destid" attribute and
not by parsing device name.

This patch also removes switchid member from struct rio_switch because it
simply duplicates the component tag and does not have other use than in
device name generation.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio: documentation update

Update RapidIO documentation files to reflect modularization changes.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio: add udev notification

Add RapidIO-specific modalias generation to enable udev notifications
about RapidIO-specific events.

The RapidIO modalias string format is shown below:

"rapidio:vNNNNdNNNNavNNNNadNNNN"

Where:
v  - Device Vendor ID (16 bit),
d  - Device ID (16 bit),
av - Assembly Vendor ID (16 bit),
ad - Assembly ID (16 bit),

as they are reported in corresponding Capability Registers (CARs)
of each RapidIO device.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio: add modular build option for the subsystem core

Add a configuration option to build RapidIO subsystem core code as a
loadable kernel module.  Currently this option is available only for
x86-based platforms, with the additional patch for PowerPC planned to be
provided later.

This patch replaces kernel command line parameter "riohdid=" with its
module-specific analog "rapidio.hdid=".

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio/tsi721: convert to modular mport driver

This patch adds an option to build device driver for Tsi721 PCIe-to-SRIO
bridge device as a kernel module.

Currently this module cannot be unloaded because the existing RapidIO
subsystem code does not support dynamic removal of local RapidIO
controllers (TODO).

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio: update enumerator registration mechanism

Update enumeration/discovery method registration mechanism to allow
loading enumeration/discovery methods before all mports are registered.

Existing statically linked RapidIO subsystem expects that all available
RapidIO mport devices are initialized and registered before the
enumeration/discovery method is registered.  Switching to loadable mport
device drivers creates situation when mport device driver can be loaded
after enumeration/discovery method is attached (e.g., loadable mport
driver in a system with statically linked RapidIO core and enumerator).
This also will happen in a system with hot-pluggable RapidIO controllers.

To remove the dependency on the initialization/registration order this
patch introduces enumeration/discovery registration mechanism that
supports arbitrary registration order of mports and enumerator/discovery
methods.

The following registration rules are implemented:
- only one enumeration/discovery method can be registered for given mport ID
  (including RIO_MPORT_ANY);
- when new enumeration/discovery methods tries to attach to the registered mport
  device, method with matching mport ID will replace a default method previously
  registered for given mport (if any);
- enumeration/discovery method with target ID=RIO_MPORT_ANY will be attached
  only to mports that do not have another enumerator attached to them;
- when new mport device is registered with RapidIO subsystem, registration
  routine searches for the enumeration/discovery method with the best matching
  mport ID;

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio/rionet: rework driver initialization and removal

Rework probe/remove routines to prevent rionet driver from monopolizing
target RapidIO devices.  Fix conflict with modular RapidIO switch drivers.

Using one of RapidIO messaging channels rionet driver provides a service
layer common to all endpoint devices in a system's RapidIO network.  These
devices may also require their own specific device driver which will be
blocked from attaching to the target device by rionet (or block rionet if
loaded earlier).  To avoid conflict with device-specific drivers, the
rionet driver is reworked to be registered as a subsystem interface on the
RapidIO bus.

The reworked rio_remove_dev() and rionet_exit() routines also include
handling of individual rionet peer device removal which was not supported
before.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio: convert switch drivers to modules

Rework RapidIO switch drivers to add an option to build them as loadable
kernel modules.

This patch removes RapidIO-specific vmlinux section and converts switch
drivers to be compatible with LDM driver registration method.  To simplify
registration of device-specific callback routines this patch introduces
rio_switch_ops data structure.  The sw_sysfs() callback is removed from
the list of device-specific operations because under the new structure its
functions can be handled by switch driver's probe() and remove() routines.

If a specific switch device driver is not loaded the RapidIO subsystem
core will use default standard-based operations to configure a switch.
Because the current implementation of RapidIO enumeration/discovery method
relies on availability of device-specific operations for error management,
switch device drivers must be loaded before the RapidIO
enumeration/discovery starts.

This patch also moves several common routines from enumeration/discovery
module into the RapidIO core code to make switch-specific operations
accessible to all components of RapidIO subsystem.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rapidio/rio-scan.c: make functions static

sparse warnings:

drivers/rapidio/rio-scan.c:1143:5: sparse: symbol 'rio_enum_mport' was not declared. Should it be static?
drivers/rapidio/rio-scan.c:1246:5: sparse: symbol 'rio_disc_mport' was not declared. Should it be static?

Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: "Bounine, Alexandre" <Alexandre.Bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio/switches: remove tsi500 driver

Remove the driver for Tsi500 Parallel RapidIO switch because this device
has not been available for several years.  Since the first introduction of
Tsi500, the parallel RapidIO interface was replaced by the serial RapidIO
(sRIO) and therefore there is no value in keeping this driver.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: print a stack dump after ida_remove warning

We print a dump stack after idr_remove warning.  This is useful to find
the faulty piece of code.  Let's do the same for ida_remove, as it would
be equally useful there.

[akpm@linux-foundation.org: convert the open-coded printk+dump_stack into WARN()]
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s390: remove setting for saved_max_pfn

The only user of saved_max_pfn in s390 is read_oldmem interface but we
have removed that interface, so saved_max_pfn is now unneeded in s390, and
we needn't set it anymore.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ia64: remove setting for saved_max_pfn

The only user of saved_max_pfn in ia64 is read_oldmem interface but we
have removed that interface, so saved_max_pfn is now unneeded in ia64, and
we needn't set it anymore.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

powerpc: Remove savemaxmem parameter setup

saved_max_pfn is used to know the amount of memory that the previous
kernel used.  And for powerpc, we set saved_max_pfn by passing the kernel
commandline parameter "savemaxmem=".

The only user of saved_max_pfn in powerpc is read_oldmem interface.  Since
we have removed read_oldmem, we don't need this parameter anymore.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mips: remove savemaxmem parameter setup

saved_max_pfn is used to know the amount of memory that the previous
kernel used.  And for powerpc, we set saved_max_pfn by passing the kernel
commandline parameter "savemaxmem=".

The only user of saved_max_pfn in mips is read_oldmem interface.  Since we
have removed read_oldmem, so we don't need this parameter anymore.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/kdump/kdump.txt: remove /dev/oldmem description

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

/dev/oldmem: Remove the interface

/dev/oldmem provides the interface for us to access the "old memory" in
the dump-capture kernel.  Unfortunately, no one actually uses this
interface.

And this interface could actually cause some real problems if used on ia64
where the cached/uncached accesses are mixed.  See the discussion from the
link: https://lkml.org/lkml/2013/4/12/386.
So Eric suggested that we should remove /dev/oldmem as an unused piece of
code.

[akpm@linux-foundation.org: mention /dev/oldmem obsolescence in devices.txt]
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/exec.c:de_thread: mt-exec should update ->real_start_time

924b42d5 ("Use boot based time for process start time and boot time in
/proc") updated copy_process/do_task_stat but forgot about de_thread().
This breaks "ps axOT" if a sub-thread execs.

Note: I think that task->start_time should die.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Tomas Janousek <tjanouse@redhat.com>
Cc: Tomas Smetana <tsmetana@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/exec.c: do_execve_common(): use current_user()

Trivial cleanup.  do_execve_common() can use current_user() and avoid the
unnecessary "struct cred *cred" var.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/fork.c:copy_process(): consolidate the lockless CLONE_THREAD checks

copy_process() does a lot of "chaotic" initializations and checks
CLONE_THREAD twice before it takes tasklist.  In particular it sets
"p->group_leader = p" and then changes it again under tasklist if
!thread_group_leader(p).

This looks a bit confusing, lets create a single "if (CLONE_THREAD)" block
which initializes ->exit_signal, ->group_leader, and ->tgid.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/fork.c:copy_process(): don't add the uninitialized child to thread/task/pid lists

copy_process() adds the new child to thread_group/init_task.tasks list and
then does attach_pid(child, PIDTYPE_PID).  This means that the lockless
next_thread() or next_task() can see this thread with the wrong pid.  Say,
"ls /proc/pid/task" can list the same inode twice.

We could move attach_pid(child, PIDTYPE_PID) up, but in this case
find_task_by_vpid() can find the new thread before it was fully
initialized.

And this is already true for PIDTYPE_PGID/PIDTYPE_SID, With this patch
copy_process() initializes child->pids[*].pid first, then calls
attach_pid() to insert the task into the pid->tasks list.

attach_pid() no longer need the "struct pid*" argument, it is always
called after pid_link->pid was already set.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/fork.c:copy_process(): unify CLONE_THREAD-or-thread_group_leader code

Cleanup and preparation for the next changes.

Move the "if (clone_flags & CLONE_THREAD)" code down under "if
(likely(p->pid))" and turn it into into the "else" branch.  This makes the
process/thread initialization more symmetrical and removes one check.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fork: reorder permissions when violating number of processes limits

When a task is attempting to violate the RLIMIT_NPROC limit we have a
check to see if the task is sufficiently priviledged.  The check first
looks at CAP_SYS_ADMIN, then CAP_SYS_RESOURCE, then if the task is uid=0.

A result is that tasks which are allowed by the uid=0 check are first
checked against the security subsystem.  This results in the security
subsystem auditting a denial for sys_admin and sys_resource and then the
task passing the uid=0 check.

This patch rearranges the code to first check uid=0, since if we pass that
we shouldn't hit the security system at all.  We then check sys_resource,
since it is the smallest capability which will solve the problem.  Lastly
we check the fallback everything cap_sysadmin.  We don't want to give this
capability many places since it is so powerful.

This will eliminate many of the false positive/needless denial messages we
get when a root task tries to violate the nproc limit.  (note that
kthreads count against root, so on a sufficiently large machine we can
actually get past the default limits before any userspace tasks are
launched.)

Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/proc/kcore.c: using strlcpy() instead of strncpy()

For NUL terminated string, set '\0' at the end.

Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/proc/uptime.c:uptime_proc_show(): use get_monotonic_boottime()

Change uptime_proc_show() to use get_monotonic_boottime() instead of
do_posix_clock_monotonic_gettime() + monotonic_to_bootbased().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Tomas Janousek <tjanouse@redhat.com>
Cc: Tomas Smetana <tsmetana@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exit.c: unexport __set_special_pids()

Move __set_special_pids() from exit.c to sys.c close to its single caller
and make it static.

And rename it to set_special_pids(), another helper with this name has
gone away.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/exec.c:de_thread(): use change_pid() rather than detach_pid/attach_pid

de_thread() can use change_pid() instead of detach + attach.  This looks
better and this ensures that, say, next_thread() can never see a task with
->pid == NULL.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: '% at the end' shouldn't bypass core_uses_pid logic

"goto end" should not bypass the "Backward compatibility with
core_uses_pid" code, move this label up.

While at it,

- It is ugly to copy '|' into cn->corename and then inc
  the pointer for argv_split().

  Change format_corename() to increment pat_ptr instead.

- Remove the dead "if (*pat_ptr == 0)" in format_corename(),
  we already checked it is not zero.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: kill call_count, add core_name_size

Imho, "atomic_t call_count" is ugly and should die.  It buys nothing and
in fact it can grow more than necessary, expand doesn't check if it was
already incremented by another task.

Kill it, and introduce "static int core_name_size" updated by
expand_corename().  This is obviously racy too but harmless, and
core_name_size never grows for no reason.

We do not bother to to calculate the "right" new size, we simply do
kmalloc(size_we_need) and use ksize() to rely on kmalloc_index's decision.

Finally change format_corename() to use expand_corename(), krealloc(NULL)
is fine.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: kill cn_escape(), introduce cn_esc_printf()

The usage of cn_escape() looks really annoying, imho this sequence needs a
wrapper.  And it is buggy.  If cn_printf() does expand_corename()
cn_escape() writes to the freed memory.

Introduce cn_esc_printf() which hopefully does this all right.  It records
the index before cn_vprintf(), not "char *" which is no longer valid (in
general) after krealloc().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: cn_vprintf() has no reason to call vsnprintf() twice

cn_vprintf() looks really overcomplicated and sub-optimal.  We do not need
vsnprintf(NULL) to calculate the size we need, we can simply try to print
into the current buffer and expand/retry only if necessary.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: introduce cn_vprintf()

Turn cn_printf(...) into cn_vprintf(va_list args), reintroduce
cn_printf() as a trivial wrapper.

This simplifies the next change and cn_vprintf() will have more
callers.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coredump: format_corename() can leak cn->corename

do_coredump() assumes that format_corename() can only fail if
expand_corename() fails and frees cn->corename.  This is not true, for
example cn_print_exe_file() can fail and in this case nobody frees
cn->corename.

Change do_coredump() to always do kfree(cn->corename) after it calls
format_corename() (NULL is fine), change expand_corename() to do nothing
if kmalloc() fails.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usermodehelper: kill the sub_info->path[0] check

call_usermodehelper_exec() does nothing but returns success if path[0] ==
0.  The only user which needs this strange feature is request_module(), it
can check modprobe_path[0] itself like other users do if they want to
detect the "disabled by admin" case.

Kill it.  Not only it looks strange, it can confuse other callers.  And
this allows us to revert 264b83c0 ("usermodehelper: check
subprocess_info->path != NULL"), do_execve(NULL) is safe.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: eventpoll: do not use sigprocmask()

sigprocmask() should die. None of the current callers actually
need this strange interface.

Change fs/eventpoll.c to use set_current_blocked(). This also
means we should not worry about SIGKILL/SIGSTOP.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: add ability to get/set signal-blocked mask

crtools uses a parasite code for dumping processes.  The parasite code is
injected into a process with help PTRACE_SEIZE.

Currently crtools blocks signals from a parasite code.  If a process has
pending signals, crtools wait while a process handles these signals.

This method is not suitable for stopped tasks.  A stopped task can have a
few pending signals, when we will try to execute a parasite code, we will
need to drop SIGSTOP, but all other signals must remain pending, because a
state of processes must not be changed during checkpointing.

This patch adds two ptrace commands to set/get signal-blocked mask.

I think gdb can use this commands too.

[akpm@linux-foundation.org: be consistent with brace layout]
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: kill TIF_DEBUG

Because it is not used.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

docbook: add futexes to kernel-locking docbook

Add Fast User Mutexes (futexes) to kernel-locking docbook.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/CodingStyle: allow multiple return statements per function

A surprising number of newbies interpret this section to mean that only
one return statement is allowed per function.  Part of the problem is that
the "one return statement per function" rule is an actual style guideline
that people are used to from other projects.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/fat: use fat_msg() to replace printk() in __fat_fs_error()

Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

] nilfs2: use atomic64_t type for inodes_count and blocks_count fields in nilfs_root struct

The cp_inodes_count and cp_blocks_count are represented as __le64 type in
on-disk structure (struct nilfs_checkpoint).  But analogous fields in
in-core structure (struct nilfs_root) are represented by atomic_t type.

This patch replaces atomic_t on atomic64_t type in representation of
inodes_count and blocks_count fields in struct nilfs_root.

Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Joern Engel <joern@logfs.org>
Cc: Clemens Eisserer <linuxhippy@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nilfs2: implement calculation of free inodes count

Currently, NILFS2 returns 0 as free inodes count (f_ffree) and current
used inodes count as total file nodes in file system (f_files):

df -i
Filesystem      Inodes  IUsed   IFree IUse% Mounted on
/dev/loop0           2      2       0  100% /mnt/nilfs2

This patch implements real calculation of free inodes count.  First of
all, it is calculated total file nodes in file system as
(desc_blocks_count * groups_per_desc_block * entries_per_group).  Then, it
is calculated free inodes count as difference the total file nodes and
used inodes count.  As a result, we have such output for NILFS2:

df -i
Filesystem       Inodes   IUsed    IFree IUse% Mounted on
/dev/loop0      4194304 2114701  2079603   51% /mnt/nilfs2

Reported-by: Clemens Eisserer <linuxhippy@gmail.com>
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-sirfsoc.c: add rtc drivers for CSR SiRFprimaII and SiRFatlasVI

On CSR SiRFprimaII/atlasVI, there is a programmable 16-bit divider
(RTC_DIV) that divides the input 32.768KHz clock to the frequency that
users need (E.g.  1 Hz).  The divided real-time clock will be used to
drive a 32-bit counter (RTC_COUNTER) that provides users with the actual
time.

In each cycle of the divided real-time clock, there is a Hertz interrupt
generated to the RISC.  Users can also configure an alarm (RTC_ALARM).
When RTC_COUNTER matches the alarm, there will be an alarm interrupt
generated to the RISC.

The system RTC can generate an alarm wake-up signal to notify the power
controller to wake up from power saving mode.

Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-ds1216.c: use module_platform_driver_probe()

Use module_platform_driver_probe() macro which makes the code smaller and
simpler.

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: omap: restore back (hard-code) wakeup support

rtc-omap driver modules is used both by OMAP1/2, Davinci SoC platforms.

However, rtc wake support on OMAP1 is broken.  Hence the
device_init_wakeup() was removed from rtc-omap driver and moved to
platform board files that supported it (DA850/OMAP-L138).  [1]

However, recently [2] it was suggested that driver should always do a
device_init_wakeup(dev, true). Platforms that don't want/need
wakeup support can disable it from userspace via:

    echo disabled > /sys/devices/.../power/wakeup

Also, with the new DT boot-up, board file doesn't exist and hence there
is no way to have device wakeup support rtc.

The fix for above issues, is to hard code device_init_wakeup() inside
driver and let platforms that don't need this, handle it through the
sysfs power entry.

[1]
https://patchwork.kernel.org/patch/136731/

[2]
http://www.mail-archive.com/davinci-linux-open-source@linux.
davincidsp.com/msg26077.html

Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: add NXP PCF2127 support (i2c)

Added support for NXP PCF2127 RTC (i2c).

[akpm@linux-foundation.org: fix typo, fix warnings]
Signed-off-by: Renaud Cerrato <r.cerrato@til-technologies.fr>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-palmas.c: init wakeup before device register

Enable dev as wakeup device before calling rtc_device_register(), so that
it can create the "wakealarm" sysfs.

Signed-off-by: Wei Ni <wni@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/class: convert from Legacy pm ops to dev_pm_ops

Convert drivers/rtc/class to use dev_pm_ops for power management and
remove Legacy PM ops hooks.  With this change, rtc class registers
suspend/resume callbacks via class->pm (dev_pm_ops) instead of Legacy
class->suspend/resume.  When __device_suspend() runs call-backs, it will
find class->pm ops for the rtc class.

Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pcf2123.c: replace strict_strtoul() with kstrtoul()

The usage of strict_strtoul() is not preferred, because strict_strtoul()
is obsolete.  Thus, kstrtoul() should be used.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/interface.c: return -EBUSY, not -EACCES when device is busy

If rtc->irq_task is non-NULL and task is NULL, they always
rtc_irq_set_freq(), whenever err is set to -EBUSY it will then immediately
be set to -EACCES, misleading the caller as to the underlying problem.

Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-twl.c: cleanup with module_platform_driver() conversion

Use module_platform_driver() to register the platform driver.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-twl.c: fix rtc_reg_map initialization

Initialize the rtc_reg_map in platform_driver's probe function instead at
module_init time.  This way we can make sure that the twl-core has been
already probed and initialized (twl_priv->twl_id is valid) since the
platform device for the RTC driver will be created by the twl-core after
it finished its init.

Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-cmos.c: work around bios clearing rtc control

The bios may clear the rtc control register when resuming the system. Since the
cmos interrupt handler may now be run before the rtc_cmos is resumed, this can
cause the interrupt handler to ignore an alarm since the alarm bit is not set in
the rtc control register. To work around this, check if the rtc_cmos is
suspended and use the stored value for the rtc control register.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-twl.c: ensure IRQ is wakeup enabled

Currently, the RTC IRQ is never wakeup-enabled so is not capable of
bringing the system out of suspend.

On OMAP platforms, we have gotten by without this because the TWL RTC is
on an I2C-connected chip which is capable of waking up the OMAP via the IO
ring when the OMAP is in low-power states.

However, if the OMAP suspends without hitting the low-power states (and
the IO ring is not enabled), RTC wakeups will not work because the IRQ is
not wakeup enabled.

To fix, ensure the RTC IRQ is wakeup enabled whenever the RTC alarm is
set.

Signed-off-by: Kevin Hilman <khilman@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pcf8583.c: use PTR_RET()

Use of PTR_RET() simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pcf8563.c: use PTR_RET()

Use of PTR_RET() simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-m48t35.c: use PTR_RET()

Use of PTR_RET() simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-isl12022.c: use PTR_RET()

Use of PTR_RET() simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-da9052.c: use PTR_RET()

Use of PTR_RET() simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-mpc5121.c: use platform_{get,set}_drvdata()

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-ds1302.c: handle write protection

This chip has a control register and can prevent altering saved clock.
Without this patch we could have:

(arm)root@pac14:~# date
Tue May 21 03:08:27 MSK 2013
(arm)root@pac14:~# /etc/init.d/hwclock.sh show
Tue May 21 11:13:58 2013  -0.067322 seconds
(arm)root@pac14:~# /etc/init.d/hwclock.sh stop
[info] Saving the system clock.
[info] Hardware Clock updated to Tue May 21 03:09:01 MSK 2013.
(arm)root@pac14:~# /etc/init.d/hwclock.sh show
Tue May 21 11:14:15 2013  -0.624272 seconds

The patch enables write access to rtc before the driver tries to write
time and re-disables when time data is written.

Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-ab8500.c: add second resolution to rtc driver

Android expects the RTC to have second resolution.  On ab8540 cut2 RTC
block has a new register which allows setting seconds for wakeup alarms.

Existing registers (minutes hi, mid and low) have seen their offsets
changed. Here is the new mapping:
  * AlarmSec     (A) 0x22
  * AlarmMinLow  (M) from 0x8 to 0x23
  * AlarmMinMid  (M) from 0x9 to 0x24
  * AlarmMinHigh (M) from 0xA to 0x25

Signed-off-by: Julien Delacou <julien.delacou@stericsson.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-wm831x.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-tps80031.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-sun4v.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-starfire.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-snvs.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-rx8581.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-rs5c348.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-rx4581.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-rv3029c2.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-rs5c313.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-ps3.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pcf8583.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pcf8563.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pcf8523.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-max8997.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: <ms925.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-max77686.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-max8907.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-max6900.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-max6902.c: remove empty function

After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>