GitHub/exynos8895/android_kernel_samsung_universal8895.git
16 years ago[ARM] pxa: fix 1c104e0e4f6ab396960c058e95e18bdedcac945b
Russell King [Tue, 29 Apr 2008 20:28:03 +0000 (21:28 +0100)]
[ARM] pxa: fix 1c104e0e4f6ab396960c058e95e18bdedcac945b

The referenced commit changed the order such that the CPU code was
initialised before MFP, resulting in unregistered MFP sysfs objects
being referenced.  Reverse the link order of these so MFP is
initialised before the CPU code.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5017/1: pxa3xx: Report unsupported wakeup sources in pxa3xx_set_wake()
Mark Brown [Wed, 23 Apr 2008 09:28:18 +0000 (10:28 +0100)]
[ARM] 5017/1: pxa3xx: Report unsupported wakeup sources in pxa3xx_set_wake()

pxa3xx_set_wake() silently accepts unsupported wake sources, causing
users to believe that they have succesfully configured sources that they
haven't.  Fail the operation instead.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5020/1: magician: remove __devinit marker from pasic3_leds_info
Philipp Zabel [Thu, 24 Apr 2008 17:10:46 +0000 (18:10 +0100)]
[ARM] 5020/1: magician: remove __devinit marker from pasic3_leds_info

Platform data must not be marked with __devinit. Even __devinitdata
would be wrong as the platform driver can be compiled as a module.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5014/1: Cleanup reset state before entering suspend or resetting.
Dmitry Baryshkov [Mon, 21 Apr 2008 10:54:13 +0000 (11:54 +0100)]
[ARM] 5014/1: Cleanup reset state before entering suspend or resetting.

The kernel should clean stale bits from reset status, so that
they won't confuse the bootloader.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5013/1: Change ITE8152 interrupt numbers
Mike Rapoport [Mon, 21 Apr 2008 09:56:32 +0000 (10:56 +0100)]
[ARM] 5013/1: Change ITE8152 interrupt numbers

The patch kills the use of IRQ_GPIO() and adds
#if NR_IRQS < (IT8152_LAST_IRQ+1) statement.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5011/1: htc-pasic3: fix bug in resource pipe-through to ds1wm
Philipp Zabel [Sun, 20 Apr 2008 16:42:59 +0000 (17:42 +0100)]
[ARM] 5011/1: htc-pasic3: fix bug in resource pipe-through to ds1wm

The newly created DS1WM platform device should get a copy of the PASIC3
platform devices' resources.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5009/1: magician: remove to-be-deprecated defines for pxa_gpio_mode
Philipp Zabel [Sun, 20 Apr 2008 16:41:11 +0000 (17:41 +0100)]
[ARM] 5009/1: magician: remove to-be-deprecated defines for pxa_gpio_mode

Alternate function and direction setting is now handled
by the MFP config code or the generic GPIO API.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5008/1: magician: add magician specific input GPIOs to MFP config
Philipp Zabel [Sun, 20 Apr 2008 16:40:11 +0000 (17:40 +0100)]
[ARM] 5008/1: magician: add magician specific input GPIOs to MFP config

Some input pin configuration that is not handled by drivers. This should
serve mostly as documentation.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5007/1: magician: properly request GPIOs used by the machine code itself
Philipp Zabel [Sun, 20 Apr 2008 16:39:12 +0000 (17:39 +0100)]
[ARM] 5007/1: magician: properly request GPIOs used by the machine code itself

Registers some GPIOs used in magician.c with the GPIO API.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5006/1: Gumstix GPIO header fixup and defconfig fixup
Jaya Kumar [Sun, 20 Apr 2008 06:25:00 +0000 (07:25 +0100)]
[ARM] 5006/1: Gumstix GPIO header fixup and defconfig fixup

This patch adds the include of the GPIO header needed to make gumstix
build. The defconfig is updated to 2.6.25 and disables PCMCIA since
that has not yet been implemented for gumstix.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: Phycore pcm-990-specific code for the PXA270 Quick Capture driver
Guennadi Liakhovetski [Sun, 6 Apr 2008 21:08:15 +0000 (23:08 +0200)]
[ARM] pxa: Phycore pcm-990-specific code for the PXA270 Quick Capture driver

Platform-specific code for Phytec's phyCORE-PXA270 platform

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: V4L2 soc_camera driver for PXA270
Guennadi Liakhovetski [Fri, 11 Apr 2008 20:19:45 +0000 (22:19 +0200)]
[ARM] pxa: V4L2 soc_camera driver for PXA270

This patch adds a driver for the Quick Capture Interface on the PXA270.
It is based on the original driver from Intel, but has been re-worked
multiple times since then, now it also supports the V4L2 API.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: restrict availability of pxa2xx PCMCIA drivers
Russell King [Sat, 19 Apr 2008 15:46:54 +0000 (16:46 +0100)]
[ARM] pxa: restrict availability of pxa2xx PCMCIA drivers

Not all PXA2xx platforms provide the necessary support files for
PCMCIA to work, let alone build.  Stop the build errors by making
PXA2xx PCMCIA support only available on those platforms which have
supplied the support files.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: initialise PXA devices before platform init code
Russell King [Sat, 19 Apr 2008 09:59:24 +0000 (10:59 +0100)]
[ARM] pxa: initialise PXA devices before platform init code

Initialise PXA devices before platform initialisation, so that
platforms can parent devices to these.

Acked-by: eric miao <ymiao3@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5002/1: tosa: add two more leds
Dmitry Baryshkov [Sat, 19 Apr 2008 09:42:06 +0000 (10:42 +0100)]
[ARM] 5002/1: tosa: add two more leds

This adds support for two more leds:
the wlan one (found in SL-6000W and SL-6000L) and
the blutooth one (found in SL-6000W).

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5004/1: Tosa: make several unreferenced structures static.
Dmitry Baryshkov [Sat, 19 Apr 2008 09:42:25 +0000 (10:42 +0100)]
[ARM] 5004/1: Tosa: make several unreferenced structures static.

Now that scoop gpio's are converted to generic_gpio,
tosascoop_device and tosascoop_jc_device don't have
to be exported.

Also make tosa_gpio_* static

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 5003/1: Shut up sparse warnings
Dmitry Baryshkov [Sat, 19 Apr 2008 09:42:18 +0000 (10:42 +0100)]
[ARM] 5003/1: Shut up sparse warnings

Shut up sparse warnings by making GPIO_IRQ_MASK unisgned

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4977/2: soc - pxa2xx-ac97 - Add missing clk_enable()
Mark Brown [Tue, 15 Apr 2008 15:12:44 +0000 (16:12 +0100)]
[ARM] 4977/2: soc - pxa2xx-ac97 - Add missing clk_enable()

Add missing clk_enable()

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4976/1: zylonite: Configure GPIO for WM9713 IRQ line
Mark Brown [Tue, 15 Apr 2008 14:50:49 +0000 (15:50 +0100)]
[ARM] 4976/1: zylonite: Configure GPIO for WM9713 IRQ line

Set up the IRQ line for the WM9713 device on the Zylonite.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4974/1: Drop unused leds-tosa.
Dmitry Baryshkov [Sat, 12 Apr 2008 20:26:39 +0000 (21:26 +0100)]
[ARM] 4974/1: Drop unused leds-tosa.

As now tosa uses leds-gpio, drop leds-tosa driver.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4973/1: Tosa: use leds-gpio driver.
Dmitry Baryshkov [Sat, 12 Apr 2008 19:17:02 +0000 (20:17 +0100)]
[ARM] 4973/1: Tosa: use leds-gpio driver.

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-tosa.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4972/1: Tosa: convert scoop GPIOs usage to generic gpio code
Dmitry Baryshkov [Sat, 12 Apr 2008 19:16:16 +0000 (20:16 +0100)]
[ARM] 4972/1: Tosa: convert scoop GPIOs usage to generic gpio code

Convert set/reset_scoop_gpio to generic gpio calls.
This patch depends on the pxaficp_ir hooks patch.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4971/1: pxaficp_ir: provide startup and shutdown hooks
Dmitry Baryshkov [Sat, 12 Apr 2008 19:08:16 +0000 (20:08 +0100)]
[ARM] 4971/1: pxaficp_ir: provide startup and shutdown hooks

Let platform do some specific initialisation and cleanup
things during pxaficp_ir probing and removing. E.g. this
can be usefull to request/free gpios used by the platform
to control the transceiver.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: lubbock: move mis-placed SPI info
Russell King [Sun, 13 Apr 2008 16:38:55 +0000 (17:38 +0100)]
[ARM] pxa: lubbock: move mis-placed SPI info

The SPI information got placed in the middle of the SMC91x data.
Lets move it up a few lines so that we keep related things grouped
together.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4970/1: tosa: correct gpio used for wake up.
Dmitry Baryshkov [Sat, 12 Apr 2008 19:02:50 +0000 (20:02 +0100)]
[ARM] 4970/1: tosa: correct gpio used for wake up.

TOSA_GPIO_ON_KEY can't wakeup the device. But the board
provides TOSA_GPIO_POWERON which is OR of (on_ac) and (on_button).
Use it for wake up.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4966/1: magician: add MFP pin configuration
Philipp Zabel [Sat, 12 Apr 2008 12:29:22 +0000 (13:29 +0100)]
[ARM] 4966/1: magician: add MFP pin configuration

Although the GPIO alternate functions should be correctly set
by the bootloader, configure them here to be sure.
To save power, FFUART/BTUART/STUART are left unconfigured (output, low)
until they are needed by pxaficp or the magician GSM chipset driver.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4965/1: magician: use htc-pasic3,leds-pasic3,ds1wm,leds-gpio
Philipp Zabel [Sat, 12 Apr 2008 12:28:02 +0000 (13:28 +0100)]
[ARM] 4965/1: magician: use htc-pasic3,leds-pasic3,ds1wm,leds-gpio

This patch enables LEDs and the 1-wire bus (connected to
a DS2760 battery monitor) on the magician.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4964/1: htc-pasic3: MFD driver for PASIC3 LED control + DS1WM chip
Philipp Zabel [Sat, 12 Apr 2008 12:25:41 +0000 (13:25 +0100)]
[ARM] 4964/1: htc-pasic3: MFD driver for PASIC3 LED control + DS1WM chip

This driver will provide registers, clocks and GPIOs of
the HTC PASIC3 (AIC3) and PASIC2 (AIC2) chips to the
ds1wm and leds-pasic3 drivers.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4958/2: tosa: fix i2c registration.
Dmitry Baryshkov [Thu, 10 Apr 2008 14:43:18 +0000 (15:43 +0100)]
[ARM] 4958/2: tosa: fix i2c registration.

Add a call to pxa_set_i2c_info() to force i2c registration

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4960/1: Rewrite tosa pin configuration to use MFP tables.
Dmitry Baryshkov [Thu, 10 Apr 2008 10:00:32 +0000 (11:00 +0100)]
[ARM] 4960/1: Rewrite tosa pin configuration to use MFP tables.

Clean up all pins configuration to use currently proposed MFP table
schema.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4959/1: PXA: Fix misprint in CICR1_RGBT_CONV
Mike Rapoport [Thu, 10 Apr 2008 05:34:29 +0000 (06:34 +0100)]
[ARM] 4959/1: PXA: Fix misprint in CICR1_RGBT_CONV

This patch fixes misprint in definition of CICR1_RGBT_CONV in include/asm-arm/arch-pxa/pxa-regs.h

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4953/1: magician: add backlight power switching GPIOs
Philipp Zabel [Wed, 9 Apr 2008 18:28:53 +0000 (19:28 +0100)]
[ARM] 4953/1: magician: add backlight power switching GPIOs

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4952/1: magician: add LCD detection, LCD power switching, update pxafb settings
Philipp Zabel [Wed, 9 Apr 2008 18:27:10 +0000 (19:27 +0100)]
[ARM] 4952/1: magician: add LCD detection, LCD power switching, update pxafb settings

All magician devices I've encountered so far have featured the Toppoly
TD028STEB1 display, so the Samsung LTP280QV support is untested.
The power-on sequence is not correct because pxafb doesn't yet support
enabling the LCD controller in the middle of the it.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4951/1: magician: enable external power supply (pda_power) driver
Philipp Zabel [Wed, 9 Apr 2008 18:25:56 +0000 (19:25 +0100)]
[ARM] 4951/1: magician: enable external power supply (pda_power) driver

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4950/1: magician: enable MMC support
Philipp Zabel [Wed, 9 Apr 2008 18:24:55 +0000 (19:24 +0100)]
[ARM] 4950/1: magician: enable MMC support

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4949/1: magician: enable flash VPP GPIO and build in MTD, physmap-flash and...
Philipp Zabel [Wed, 9 Apr 2008 18:24:05 +0000 (19:24 +0100)]
[ARM] 4949/1: magician: enable flash VPP GPIO and build in MTD, physmap-flash and JFFS2

This enables rootfs on StrataFlash if the bootloader supplies the
partition list.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4948/1: magician: use htc-egpio to drive the GPIO/IRQ expander CPLD
Philipp Zabel [Wed, 9 Apr 2008 18:22:57 +0000 (19:22 +0100)]
[ARM] 4948/1: magician: use htc-egpio to drive the GPIO/IRQ expander CPLD

needed for power management (audio, BT, charging, GSM, LCD, SD), GSM, flash and SD operation and audio routing.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4947/1: htc-egpio, a driver for GPIO/IRQ expanders with fixed input/output...
Philipp Zabel [Wed, 9 Apr 2008 18:20:34 +0000 (19:20 +0100)]
[ARM] 4947/1: htc-egpio, a driver for GPIO/IRQ expanders with fixed input/output pins

implemented in CPLD chips on several HTC devices.

The original driver was written by Kevin O'Connor, I have adapted it to
use gpiolib and made the bus/register widths configurable.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4944/2: magician: enable i2c bus
Philipp Zabel [Wed, 9 Apr 2008 18:14:15 +0000 (19:14 +0100)]
[ARM] 4944/2: magician: enable i2c bus

Since recent PXA changes the (non-power-)I2C bus has to be explicitly
enabled from board initialisation code.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4943/2: magician: fix magician.h GPIO header includes
Philipp Zabel [Wed, 9 Apr 2008 18:11:52 +0000 (19:11 +0100)]
[ARM] 4943/2: magician: fix magician.h GPIO header includes

PXA GPIO definitions were split from pxa-regs.h into pxa2xx-gpio.h.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4942/1: magician: fix the backlight driver name
Philipp Zabel [Tue, 8 Apr 2008 18:36:06 +0000 (19:36 +0100)]
[ARM] 4942/1: magician: fix the backlight driver name

corgi_bl was renamed to generic_bl.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4941/1: Add initial defconfig for HTC Magician PDA phones
Philipp Zabel [Tue, 8 Apr 2008 18:35:18 +0000 (19:35 +0100)]
[ARM] 4941/1: Add initial defconfig for HTC Magician PDA phones

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4946/1: pxa3xx: Print an error if we refuse to suspend
Mark Brown [Wed, 9 Apr 2008 10:32:21 +0000 (11:32 +0100)]
[ARM] 4946/1: pxa3xx: Print an error if we refuse to suspend

The PXA3xx will not suspend if there are no wakeup sources configured.
Print a diagnostic message to make it easier for the user to see what's
happening.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4901/3: mainstone: Register primary I2C bus
Mark Brown [Mon, 7 Apr 2008 16:16:34 +0000 (17:16 +0100)]
[ARM] 4901/3: mainstone: Register primary I2C bus

Mainstone has the primary I2C bus exposed for use on plugin modules.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4867/1: Adds flash, udc, mci support for gumstix F boards
Jaya Kumar [Sat, 15 Mar 2008 04:11:07 +0000 (05:11 +0100)]
[ARM] 4867/1: Adds flash, udc, mci support for gumstix F boards

This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are:
- Steve Sakoman as maintainer
- cleanup for udc and mci setup

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: remove keypad register definitions from pxa-regs.h
eric miao [Fri, 22 Feb 2008 05:48:15 +0000 (13:48 +0800)]
[ARM] pxa: remove keypad register definitions from pxa-regs.h

Keypad registers are now fully defined within pxa27x-keypad.c, no
need to keep those definitions in pxa-regs.h

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: add keypad support for littleton
eric miao [Wed, 23 Jan 2008 07:07:22 +0000 (15:07 +0800)]
[ARM] pxa: add keypad support for littleton

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: add keypad support for zylonite
eric miao [Wed, 23 Jan 2008 06:25:50 +0000 (14:25 +0800)]
[ARM] pxa: add keypad support for zylonite

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: add partial keypad support for mainstone
eric miao [Wed, 23 Jan 2008 06:25:27 +0000 (14:25 +0800)]
[ARM] pxa: add partial keypad support for mainstone

This is partial because mainstone's keypad is really special, some of
the keys like '1', '2', ... are actually connected to two row/column
juntions, thus pressing '1' is equivalent to pressing 'A' & 'H'.

This is really brain damanged since it makes distinguishing between
pressing '1' and multiple keys pressing of 'A' & 'H' difficult.

So these special keys are not supported for the time being.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: add pxa27x_keypad device and pxa_set_keypad_info()
eric miao [Wed, 23 Jan 2008 05:39:13 +0000 (13:39 +0800)]
[ARM] pxa: add pxa27x_keypad device and pxa_set_keypad_info()

also update the clk definitions in pxa27x and pxa3xx.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: use gpio_keys.c to support mainstone's wakeup switch of GPIO1
eric miao [Tue, 11 Mar 2008 02:06:38 +0000 (10:06 +0800)]
[ARM] pxa: use gpio_keys.c to support mainstone's wakeup switch of GPIO1

NOTE: currently don't know if the key code of KEY_SUSPEND is fit for
such usage.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x}
eric miao [Tue, 11 Mar 2008 01:46:28 +0000 (09:46 +0800)]
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x}

Changes include:

1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
   the board capability of this pin to wakeup the system

2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
   enable/disable wakeup from GPIOs and keypad GPIO

   * these functions are currently kept in mfp-pxa2xx.c due to their
     dependency to the MFP configuration

3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
   is set on incorrect pins

So that the GPIO's wakeup capability is now decided by the following:

   a) processor's capability: (only those GPIOs which have dedicated
      bits within PWER/PRER/PFER can wakeup the system), this is
      initialized by pxa{25x,27x}_init_mfp()

   b) board design decides:
      - whether the pin is designed to wakeup the system (some of
        the GPIOs are configured as other functions, which is not
        intended to be a wakeup source), by OR'ing the pin config
        with MFP_LPM_CAN_WAKEUP

      - which edge the pin is designed to wakeup the system, this
        may depends on external peripherals/connections, which is
        totally board specific; this is indicated by MFP_LPM_EDGE_*

   c) the corresponding device's (most likely the gpio_keys.c) wakeup
      attribute:

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: use new pin configuration mechanism for lubbock
eric miao [Wed, 13 Feb 2008 00:52:38 +0000 (08:52 +0800)]
[ARM] pxa: use new pin configuration mechanism for lubbock

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: use new pin configuration mechanism for mainstone
eric miao [Mon, 4 Feb 2008 09:15:50 +0000 (17:15 +0800)]
[ARM] pxa: use new pin configuration mechanism for mainstone

1. the following code to configure PGSRx is no way portable and
   intuitive:

- PGSR0 = 0x00008800;
-       PGSR1 = 0x00000002;
-       PGSR2 = 0x0001FC00;
-       PGSR3 = 0x00001F81;

   this is removed as low power state has already been encoded in
   the pin configuration definitions.

   Note: there is no specific reason for some of the GPIOs to drive
   high in low power mode as indicated by the above setting, those
   bits are ignored, and the result is validated to work.

2. the following code to configure GPIO wakeup is removed as this
   is now totally handled by pxa2xx_mfp_config():

-       PWER  = 0xC0000002;
-       PRER  = 0x00000002;
-       PFER  = 0x00000002;

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: move ARRAY_AND_SIZE definition to generic.h
eric miao [Sun, 3 Feb 2008 07:49:09 +0000 (15:49 +0800)]
[ARM] pxa: move ARRAY_AND_SIZE definition to generic.h

for use by other platforms

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
eric miao [Wed, 5 Mar 2008 09:16:29 +0000 (17:16 +0800)]
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}

Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs.  A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.

A pin configuration on pxa{25x,27x} is composed of:

    - alternate function selection (or pin mux as commonly called)
    - low power state or sleep state
    - wakeup enabling from low power mode

The following MFP_xxx bit definitions in mfp.h are re-used:

    - MFP_PIN(x)
    - MFP_AFx
    - MFP_LPM_DRIVE_{LOW, HIGH}
    - MFP_LPM_EDGE_*

Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:

    - MFP_CFG_IN  : for input alternate functions
    - MFP_CFG_OUT : for output alternate functions

Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT().  As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.

Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output.  The actual
direction of the GPIO is configured by gpio_direction_{input, output}

Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.

E.g.  invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:

    enable_irq_wake( gpio_to_irq(35) );

To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).

Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:

    - MFP_LPM_WAKEUP_ENABLE

The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:

    - WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
    - WAKEUP_ON_LEVEL_HIGH

The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.

These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.

The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: separate GPIOs and their mode definitions to pxa2xx-gpio.h
eric miao [Mon, 3 Mar 2008 01:44:25 +0000 (09:44 +0800)]
[ARM] pxa: separate GPIOs and their mode definitions to pxa2xx-gpio.h

two reasons:
1. GPIO namings and their mode definitions are conceptually not part
   of the PXA register definitions

2. this is actually a temporary move in the transition of PXA2xx to
   use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
   code will still work and new code can be added in step by step

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: move mfp sysdev registeration out for suspend/resume order
eric miao [Mon, 4 Feb 2008 02:07:09 +0000 (10:07 +0800)]
[ARM] pxa: move mfp sysdev registeration out for suspend/resume order

MFP configurations after resume should be done before the GPIO registers
are restored.  Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: rename mfp.c to mfp-pxa3xx.c to indicate it's pxa3xx specific
eric miao [Mon, 3 Mar 2008 00:59:13 +0000 (08:59 +0800)]
[ARM] pxa: rename mfp.c to mfp-pxa3xx.c to indicate it's pxa3xx specific

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: make pxa_gpio_irq_type() processor generic
eric miao [Tue, 4 Mar 2008 09:18:38 +0000 (17:18 +0800)]
[ARM] pxa: make pxa_gpio_irq_type() processor generic

The main issue here is that pxa3xx does not have GAFRx registers,
access directly to these registers should be avoided for pxa3xx:

1. introduce __gpio_is_occupied() to indicate the GAFRx and GPDRx
   registers are already configured on pxa{25x,27x} while returns
   0 always on pxa3xx

2. pxa_gpio_mode(gpio | GPIO_IN) is replaced directly with assign-
   ment of GPDRx, the side effect of this change is that the pin
   _must_ be configured before use, pxa_gpio_irq_type() will not
   change the pin to GPIO, as this restriction is sane, esp. with
   the new MFP framework

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: move GPIO sysdev outside of generic.c into gpio.c
eric miao [Tue, 4 Mar 2008 08:13:58 +0000 (16:13 +0800)]
[ARM] pxa: move GPIO sysdev outside of generic.c into gpio.c

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: merge assignment of set_wake into pxa_init_{irq,gpio}()
eric miao [Tue, 4 Mar 2008 06:19:58 +0000 (14:19 +0800)]
[ARM] pxa: merge assignment of set_wake into pxa_init_{irq,gpio}()

To further clean up the GPIO and IRQ structure:

1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
   function pxa_init_gpio()

2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
   an argument

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: integrate low IRQ chip (ICIP) and high IRQ chip (ICIP2) into one
eric miao [Tue, 4 Mar 2008 05:53:05 +0000 (13:53 +0800)]
[ARM] pxa: integrate low IRQ chip (ICIP) and high IRQ chip (ICIP2) into one

This makes the code better organized and simplified a bit.  The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.

This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable.  The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)

The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).

"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: move GPIO IRQ specific code out of irq.c into gpio.c
eric miao [Tue, 4 Mar 2008 03:42:26 +0000 (11:42 +0800)]
[ARM] pxa: move GPIO IRQ specific code out of irq.c into gpio.c

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: introduce GPIO_CHIP() macro to clean up the definitions
eric miao [Mon, 3 Mar 2008 05:20:20 +0000 (13:20 +0800)]
[ARM] pxa: introduce GPIO_CHIP() macro to clean up the definitions

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: cleanup the coding style of pxa_gpio_set_type()
eric miao [Tue, 4 Mar 2008 03:18:48 +0000 (11:18 +0800)]
[ARM] pxa: cleanup the coding style of pxa_gpio_set_type()

by

1. wrapping long lines and making comments tidy

2. using IRQ_TYPE_* instead of migration macros __IRQT_*

3. introduce a pr_debug() for the commented printk(KERN_DEBUG ...)
   stuff

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: make GPIO IRQ code less dependent on the internal IRQs
eric miao [Tue, 4 Mar 2008 03:12:14 +0000 (11:12 +0800)]
[ARM] pxa: make GPIO IRQ code less dependent on the internal IRQs

by:

1. introduce dedicated pxa_{mask,unmask}_low_gpio()

2. remove set_irq_chip(IRQ_GPIO_2_x, ...) which has already been
   initialized in pxa_init_irq()

3. introduce dedicated pxa_init_gpio_set_wake()

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] pxa: generalize the muxed gpio IRQ handling code with loop and ffs()
eric miao [Tue, 4 Mar 2008 02:57:18 +0000 (10:57 +0800)]
[ARM] pxa: generalize the muxed gpio IRQ handling code with loop and ffs()

1. As David Brownell suggests, using ffs() is going to make the loop
   a bit faster (by avoiding unnecessary shift and iteration)

2. Russell suggested find_{first,next}_bit() being used with the
   gedr[] array

Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4868/1: Enhance pxa270 GPIO definitions
Robert Jarzmik [Sun, 16 Mar 2008 10:55:32 +0000 (11:55 +0100)]
[ARM] 4868/1: Enhance pxa270 GPIO definitions

Enhanced GPIO alternate functions descriptions,
taken from Intel PXA270 Developers Manual.

Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4834/3: Convert ASoC pxa2xx-ac97 driver to use the clock API
Mark Brown [Tue, 4 Mar 2008 10:14:24 +0000 (11:14 +0100)]
[ARM] 4834/3: Convert ASoC pxa2xx-ac97 driver to use the clock API

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4833/3: Convert non-SoC PXA2xx AC97 driver to clock API
Mark Brown [Tue, 4 Mar 2008 10:14:25 +0000 (11:14 +0100)]
[ARM] 4833/3: Convert non-SoC PXA2xx AC97 driver to clock API

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4832/2: Support AC97CLK on PXA3xx via the clock API
Mark Brown [Tue, 4 Mar 2008 10:14:23 +0000 (11:14 +0100)]
[ARM] 4832/2: Support AC97CLK on PXA3xx via the clock API

The AC97 clock rate on PXA3xx is generated with a configurable divider
from sys_pll.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4831/2: Add PXA2xx AC97 clocks to clock API
Mark Brown [Tue, 4 Mar 2008 10:14:22 +0000 (11:14 +0100)]
[ARM] 4831/2: Add PXA2xx AC97 clocks to clock API

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] 4830/1: Add support for the CLK_POUT pin on PXA3xx CPUs
Mark Brown [Wed, 13 Feb 2008 15:39:21 +0000 (16:39 +0100)]
[ARM] 4830/1: Add support for the CLK_POUT pin on PXA3xx CPUs

Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years ago[ARM] Update mach-types
Russell King [Sat, 8 Mar 2008 15:58:03 +0000 (15:58 +0000)]
[ARM] Update mach-types

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16 years agoLinux 2.6.25-rc7
Linus Torvalds [Wed, 26 Mar 2008 01:38:14 +0000 (18:38 -0700)]
Linux 2.6.25-rc7

16 years agoACPI: fix Medion _PRT quirk (use "ISA_", not "ISA")
Bjorn Helgaas [Tue, 25 Mar 2008 17:21:11 +0000 (11:21 -0600)]
ACPI: fix Medion _PRT quirk (use "ISA_", not "ISA")

This fixes the builtin RTL8139 NIC on the Medion MD9580-F laptop.  The
BIOS reports the interrupt routing incorrectly.  I recently added a
quirk to work around this, and this patch fixes a typo in the quirk.

We pad every ACPI pathname component to four characters, so ".ISA." will
never match anything.  We need ".ISA_." instead.

Thank you Johann-Nikolaus Andreae <johann-nikolaus.andreae@nacs.de>
for patiently testing this patch.

See http://bugzilla.kernel.org/show_bug.cgi?id=4773

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
16 years agoMerge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
Linus Torvalds [Tue, 25 Mar 2008 16:06:44 +0000 (09:06 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Fix docbook problem
  ASoC/TLV320AIC3X: Stop I2C driver ID abuse
  i2c-omap: Fix unhandled fault
  i2c-bfin-twi: Disable BF54x support for now

16 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
Linus Torvalds [Tue, 25 Mar 2008 16:06:19 +0000 (09:06 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/avi/kvm

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: MMU: Fix memory leak on guest demand faults
  KVM: VMX: convert init_rmode_tss() to slots_lock
  KVM: MMU: handle page removal with shadow mapping
  KVM: MMU: Fix is_rmap_pte() with io ptes
  KVM: VMX: Restore tss even on x86_64

16 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
Linus Torvalds [Tue, 25 Mar 2008 15:57:47 +0000 (08:57 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  [PATCH] get stack footprint of pathname resolution back to relative sanity
  [PATCH] double iput() on failure exit in hugetlb
  [PATCH] double dput() on failure exit in tiny-shmem
  [PATCH] fix up new filp allocators
  [PATCH] check for null vfsmount in dentry_open()
  [PATCH] reiserfs: eliminate private use of struct file in xattr
  [PATCH] sanitize hppfs
  hppfs pass vfsmount to dentry_open()
  [PATCH] restore export of do_kern_mount()

16 years agoKVM: MMU: Fix memory leak on guest demand faults
Avi Kivity [Sun, 23 Mar 2008 12:21:08 +0000 (14:21 +0200)]
KVM: MMU: Fix memory leak on guest demand faults

While backporting 72dc67a69690288538142df73a7e3ac66fea68dc, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline).  This caused a page reference leak, resulting in a
fairly massive memory leak.

Fix by removing the extraneous gfn_to_page() call.

Signed-off-by: Avi Kivity <avi@qumranet.com>
16 years agoKVM: VMX: convert init_rmode_tss() to slots_lock
Marcelo Tosatti [Tue, 18 Mar 2008 20:42:34 +0000 (17:42 -0300)]
KVM: VMX: convert init_rmode_tss() to slots_lock

init_rmode_tss was forgotten during the conversion from mmap_sem to
slots_lock.

INFO: task qemu-system-x86:3748 blocked for more than 120 seconds.
Call Trace:
 [<ffffffff8053d100>] __down_read+0x86/0x9e
 [<ffffffff8053fb43>] do_page_fault+0x346/0x78e
 [<ffffffff8053d235>] trace_hardirqs_on_thunk+0x35/0x3a
 [<ffffffff8053dcad>] error_exit+0x0/0xa9
 [<ffffffff8035a7a7>] copy_user_generic_string+0x17/0x40
 [<ffffffff88099a8a>] :kvm:kvm_write_guest_page+0x3e/0x5f
 [<ffffffff880b661a>] :kvm_intel:init_rmode_tss+0xa7/0xf9
 [<ffffffff880b7d7e>] :kvm_intel:vmx_vcpu_reset+0x10/0x38a
 [<ffffffff8809b9a5>] :kvm:kvm_arch_vcpu_setup+0x20/0x53
 [<ffffffff8809a1e4>] :kvm:kvm_vm_ioctl+0xad/0x1cf
 [<ffffffff80249dea>] __lock_acquire+0x4f7/0xc28
 [<ffffffff8028fad9>] vfs_ioctl+0x21/0x6b
 [<ffffffff8028fd75>] do_vfs_ioctl+0x252/0x26b
 [<ffffffff8028fdca>] sys_ioctl+0x3c/0x5e
 [<ffffffff8020b01b>] system_call_after_swapgs+0x7b/0x80

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
16 years agoKVM: MMU: handle page removal with shadow mapping
Marcelo Tosatti [Mon, 17 Mar 2008 13:08:18 +0000 (10:08 -0300)]
KVM: MMU: handle page removal with shadow mapping

Do not assume that a shadow mapping will always point to the same host
frame number.  Fixes crash with madvise(MADV_DONTNEED).

[avi: move after first printk(), add another printk()]

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
16 years agoKVM: MMU: Fix is_rmap_pte() with io ptes
Avi Kivity [Sun, 23 Mar 2008 10:18:19 +0000 (12:18 +0200)]
KVM: MMU: Fix is_rmap_pte() with io ptes

is_rmap_pte() doesn't take into account io ptes, which have the avail bit set.

Signed-off-by: Avi Kivity <avi@qumranet.com>
16 years agoKVM: VMX: Restore tss even on x86_64
Avi Kivity [Sun, 16 Mar 2008 16:48:26 +0000 (18:48 +0200)]
KVM: VMX: Restore tss even on x86_64

The vmx hardware state restore restores the tss selector and base address, but
not its length.  Usually, this does not matter since most of the tss contents
is within the default length of 0x67.  However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted.  The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.

Fix by restoring the tss length.  Note that i386 had this working already.

Closes bugzilla 10246.

Signed-off-by: Avi Kivity <avi@qumranet.com>
16 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
Linus Torvalds [Tue, 25 Mar 2008 06:24:16 +0000 (23:24 -0700)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: Fix cut-and-paste error in rtl8150.c
  USB: ehci: stop vt6212 bus hogging
  USB: sierra: add another device id
  USB: sierra: dma fixes
  USB: add support for Motorola ROKR Z6 cellphone in mass storage mode
  USB: isd200: fix memory leak in isd200_get_inquiry_data
  USB: pl2303: another product ID
  USB: new quirk flag to avoid Set-Interface
  USB: fix gadgetfs class request delegation

16 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6
Linus Torvalds [Tue, 25 Mar 2008 06:23:39 +0000 (23:23 -0700)]
Merge git://git./linux/kernel/git/gregkh/driver-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  driver core: debug for bad dev_attr_show() return value.
  UIO: add pgprot_noncached() to UIO mmap code

16 years agoPCI: revert "pcie: utilize pcie transaction pending bit"
Andrew Morton [Mon, 17 Mar 2008 21:21:18 +0000 (14:21 -0700)]
PCI: revert "pcie: utilize pcie transaction pending bit"

Revert as it is reported to cause problems for people.

commit 4348a2dc49f9baecd34a9b0904245488c6189398
Author: Shaohua Li <shaohua.li@intel.com>
Date:   Wed Oct 24 10:45:08 2007 +0800

    pcie: utilize pcie transaction pending bit

    PCIE has a mechanism to wait for Non-Posted request to complete. I think
    pci_disable_device is a good place to do this.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the regression reported at
http://bugzilla.kernel.org/show_bug.cgi?id=10065

Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Soeren Sonnenburg <kernel@nn7.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoPCI: iova: lockdep false alarm fix
Mark Gross [Tue, 4 Mar 2008 22:59:31 +0000 (14:59 -0800)]
PCI: iova: lockdep false alarm fix

lockdep goes off on the iova copy_reserved_iova() because it and a function
it calls grabs locks in the from, and the to of the copy operation.

The function grab locks of the same lock classes triggering the warning.  The
first lock grabbed is for the constant reserved areas that is never accessed
after early boot.  Technically you could do without grabbing the locks for the
"from" structure its copying reserved areas from.

But dropping the from locks to me looks wrong, even though it would be ok.

The affected code only runs in early boot as its setting up the DMAR
engines.

This patch gives the reserved_ioval_list locks special lockdep classes.

Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agodriver core: debug for bad dev_attr_show() return value.
Andrew Morton [Tue, 4 Mar 2008 23:09:07 +0000 (15:09 -0800)]
driver core: debug for bad dev_attr_show() return value.

Try to find the culprit who caused
http://bugzilla.kernel.org/show_bug.cgi?id=10150

Cc: <balajirrao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUIO: add pgprot_noncached() to UIO mmap code
Jean-Samuel Chenard [Fri, 14 Mar 2008 10:28:36 +0000 (11:28 +0100)]
UIO: add pgprot_noncached() to UIO mmap code

Mapping of physical memory in UIO needs pgprot_noncached() to ensure
that IO memory is not cached. Without pgprot_noncached(), it (accidentally)
works on x86 and arm, but fails on PPC.

Signed-off-by: Jean-Samuel Chenard <jsamch@gmail.com>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: Fix cut-and-paste error in rtl8150.c
Robert P. J. Day [Mon, 10 Mar 2008 00:44:52 +0000 (20:44 -0400)]
USB: Fix cut-and-paste error in rtl8150.c

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: ehci: stop vt6212 bus hogging
Rene Herman [Thu, 20 Mar 2008 07:58:16 +0000 (00:58 -0700)]
USB: ehci: stop vt6212 bus hogging

The VIA VT6212 defaults to only waiting 1us between passes over EHCI's
async ring, which hammers PCI badly ... and by preventing other devices
from accessing the bus, causes problems like drops in IDE throughput,
a problem that's been bugging users of those chips for several years.

A (partial) datasheet for this chip eventually turned up, letting us
see how to make it use a VIA-specific register to switch over to the
the normal 10us value instead, as suggested by the EHCI specification
Solution noted by Lev A. Melnikovsky.

It's not clear whether this register exists on other VIA chips; we
know that it's ineffective on the vt8235.  So this patch only applies
to chips that seem to be incarnations of the (discrete) vt6212.

Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Lev A. Melnikovsky <melnikovsky@mail.ru>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: sierra: add another device id
Kevin Lloyd [Fri, 14 Mar 2008 07:53:24 +0000 (00:53 -0700)]
USB: sierra: add another device id

Add support for the MC8775 device to the sierra driver.

Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: sierra: dma fixes
Oliver Neukum [Fri, 14 Mar 2008 07:53:24 +0000 (00:53 -0700)]
USB: sierra: dma fixes

while I was adding autosuspend to that driver I noticed a few issues.
You were having DMAed buffers as a part of a structure.
This will fail on platforms that are not DMA-coherent (arm, sparc, ppc, ...)
Please test this patch to fix it.

Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: add support for Motorola ROKR Z6 cellphone in mass storage mode
Constantin Baranov [Sun, 16 Mar 2008 20:04:23 +0000 (20:04 +0000)]
USB: add support for Motorola ROKR Z6 cellphone in mass storage mode

Motorola ROKR Z6 cellphone has bugs in its USB, so it is impossible to use
it as mass storage. Patch describes new "unusual" USB device for it with
FIX_INQUIRY and FIX_CAPACITY flags and new BULK_IGNORE_TAG flag.
Last flag relaxes check for equality of bcs->Tag and us->tag in
usb_stor_Bulk_transport routine.

Signed-off-by: Constantin Baranov <const@tltsu.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: isd200: fix memory leak in isd200_get_inquiry_data
Boaz Harrosh [Mon, 17 Mar 2008 21:21:01 +0000 (14:21 -0700)]
USB: isd200: fix memory leak in isd200_get_inquiry_data

If the inquiry fails then the info structure on us->extra was not freed.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: pl2303: another product ID
Max Arnold [Thu, 20 Mar 2008 09:43:56 +0000 (16:43 +0700)]
USB: pl2303: another product ID

Device like this http://aldiga.com/english/A-100-USB-EDGE10.htm
contains Prolific 2303 chip.
Actually their site a bit outdated - I have AlDiga AL-11U
GSM/GPRS/EDGE modem and it works with pl2303 module after adding
corresponding product ID.

By default modem uses baud rate 460800.  GSM chipset - SIMCom SIM600,
quad band 850/900/1800/1900 MHz

Device info:

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=067b ProdID=0611 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=pl2303
E:  Ad=81(I) Atr=03(Int.) MxPS=  10 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

From: Max Arnold <lwarxx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: new quirk flag to avoid Set-Interface
Alan Stern [Tue, 11 Mar 2008 14:20:12 +0000 (10:20 -0400)]
USB: new quirk flag to avoid Set-Interface

This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request.  A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
16 years agoUSB: fix gadgetfs class request delegation
Roy Hashimoto [Wed, 12 Mar 2008 21:55:31 +0000 (13:55 -0800)]
USB: fix gadgetfs class request delegation

gadgetfs (drivers/usb/gadget/inode.c) was not delegating all
non-device requests to userspace.  This patch makes the handling of
all request cases consistent.

Signed-off-by: Roy Hashimoto <hashimot@alumni.caltech.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>