scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION

On a dual controller setup with multipath enabled, some MEDIUM ERRORs
caused both paths to be failed, thus I/O got queued/blocked since the
'queue_if_no_path' feature is enabled by default on IPR controllers.

This example disabled 'queue_if_no_path' so the I/O failure is seen at
the sg_dd program.  Notice that after the sg_dd test-case, both paths
are in 'failed' state, and both path/priority groups are in 'enabled'
state (not 'active') -- which would block I/O with 'queue_if_no_path'.

    # sg_dd if=/dev/dm-2 bs=4096 count=1 dio=1 verbose=4 blk_sgio=0
    <...>
    read(unix): count=4096, res=-1
    sg_dd: reading, skip=0 : Input/output error
    <...>

    # dmesg
    [...] sd 2:2:16:0: [sds] FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
    [...] sd 2:2:16:0: [sds] Sense Key : Medium Error [current]
    [...] sd 2:2:16:0: [sds] Add. Sense: Unrecovered read error - recommend rewrite the data
    [...] sd 2:2:16:0: [sds] CDB: Read(10) 28 00 00 00 00 00 00 00 20 00
    [...] blk_update_request: I/O error, dev sds, sector 0
    [...] device-mapper: multipath: Failing path 65:32.
    <...>
    [...] device-mapper: multipath: Failing path 65:224.

    # multipath -l
    1IBM_IPR-0_59C2AE0000001F80 dm-2 IBM     ,IPR-0   59C2AE00
    size=5.2T features='0' hwhandler='1 alua' wp=rw
    |-+- policy='service-time 0' prio=0 status=enabled
    | `- 2:2:16:0 sds  65:32  failed undef running
    `-+- policy='service-time 0' prio=0 status=enabled
      `- 1:2:7:0  sdae 65:224 failed undef running

This is not the desired behavior. The dm-multipath explicitly checks
for the MEDIUM ERROR case (and a few others) so not to fail the path
(e.g., I/O to other sectors could potentially happen without problems).
See dm-mpath.c :: do_end_io_bio() -> noretry_error() !->! fail_path().

The problem trace is:

1) ipr_scsi_done()  // SENSE KEY/CHECK CONDITION detected, go to..
2) ipr_erp_start()  // ipr_is_gscsi() and masked_ioasc OK, go to..
3) ipr_gen_sense()  // masked_ioasc is IPR_IOASC_MED_DO_NOT_REALLOC,
                    // so set DID_PASSTHROUGH.

4) scsi_decide_disposition()  // check for DID_PASSTHROUGH and return
                              // early on, faking a DID_OK.. *instead*
                              // of reaching scsi_check_sense().

                              // Had it reached the latter, that would
                              // set host_byte to DID_MEDIUM_ERROR.

5) scsi_finish_command()
6) scsi_io_completion()
7) __scsi_error_from_host_byte()  // That would be converted to -ENODATA
<...>
8) dm_softirq_done()
9) multipath_end_io()
10) do_end_io()
11) noretry_error()  // And that is checked in dm-mpath :: noretry_error()
                     // which would cause fail_path() not to be called.

With this patch applied, the I/O is failed but the paths are not.  This
multipath device continues accepting more I/O requests without blocking.
(and notice the different host byte/driver byte handling per SCSI layer).

    # dmesg
    [...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
    [...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 40 00
    [...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
    [...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
    [...] blk_update_request: critical medium error, dev sdaf, sector 0
    [...] blk_update_request: critical medium error, dev dm-6, sector 0
    [...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
    [...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 10 00
    [...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
    [...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
    [...] blk_update_request: critical medium error, dev sdaf, sector 0
    [...] blk_update_request: critical medium error, dev dm-6, sector 0
    [...] Buffer I/O error on dev dm-6, logical block 0, async page read

    # multipath -l 1IBM_IPR-0_59C2AE0000001F80
    1IBM_IPR-0_59C2AE0000001F80 dm-6 IBM     ,IPR-0   59C2AE00
    size=5.2T features='1 queue_if_no_path' hwhandler='1 alua' wp=rw
    |-+- policy='service-time 0' prio=0 status=active
    | `- 2:2:7:0  sdaf 65:240 active undef running
    `-+- policy='service-time 0' prio=0 status=enabled
      `- 1:2:7:0  sdh  8:112  active undef running

Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: fix PCI error recovery path

During a PCI error recovery, if aac_check_health() is not aware that a
PCI error happened and we have an offline PCI channel, it might trigger
some errors (like NULL pointer dereference) and inhibit the error
recovery process to complete.

This patch makes the health check procedure aware of PCI channel issues,
and in case of error recovery process, the function
aac_adapter_check_health() returns -1 and let the recovery process to
complete successfully. This patch was tested on upstream kernel
v4.11-rc5 in PowerPC ppc64le architecture with adapter 9005:028d
(VID:DID) - the error recovery procedure was able to recover fine.

Fixes: 5c63f7f710bd ("aacraid: Added EEH support")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sd: Fix capacity calculation with 32-bit sector_t

We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.

Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.

Cc: <stable@vger.kernel.org>
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add fix to read correct register value for ISP82xx.

Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.

Fixes: a465537ad1a4 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Fix crash due to unsolicited FIP VLAN response.

We need to initialize qedf->fipvlan_compl in __qedf_probe so that if we
receive an unsolicited FIP VLAN response, the system doesn't crash due
to trying to complete an uninitialized completion.

Also add a check to see if there are any waiters on the completion so we
don't inadvertantly kick start the discovery process due to the
unsolicited frame.

Fixed the crash:

<1>BUG: unable to handle kernel NULL pointer dereference at (null)
<1>IP: [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4>PGD 0
<4>Oops: 0000 [#1] SMP
<4>last sysfs file: /sys/devices/system/cpu/online
<4>CPU 7
<4>Modules linked in: autofs4 nfs lockd fscache auth_rpcgss nfs_acl sunrpc target_core_iblock target_core_file target_core_pscsi target_core_mod configfs bnx2fc cnic fcoe 8021q garp stp llc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 vfat fat uinput ipmi_devintf microcode power_meter acpi_ipmi ipmi_si ipmi_msghandler iTCO_wdt iTCO_vendor_support dcdbas sg joydev sb_edac edac_core lpc_ich mfd_core shpchp tg3 ptp pps_core ext4 jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif qedi(U) iscsi_boot_sysfs libiscsi scsi_transport_iscsi uio qedf(U) libfcoe libfc scsi_transport_fc scsi_tgt qede(U) qed(U) ahci megaraid_sas wmi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: speedstep_lib]
<4>
<4>Pid: 1485, comm: qedf_11_ll2 Not tainted 2.6.32-642.el6.x86_64 #1 Dell Inc. PowerEdge R730/0599V5
<4>RIP: 0010:[<ffffffff8105ed71>]  [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4>RSP: 0018:ffff881068a83d50  EFLAGS: 00010086
<4>RAX: ffffffffffffffe8 RBX: ffff88106bf42de0 RCX: 0000000000000000
<4>RDX: 0000000000000000 RSI: 0000000000000003 RDI: ffff88106bf42de0
<4>RBP: ffff881068a83d90 R08: 0000000000000000 R09: 00000000fffffffe
<4>R10: 0000000000000000 R11: 000000000000000b R12: 0000000000000286
<4>R13: ffff88106bf42de8 R14: 0000000000000000 R15: 0000000000000000
<4>FS:  0000000000000000(0000) GS:ffff88089c460000(0000) knlGS:0000000000000000
<4>CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
<4>CR2: 0000000000000000 CR3: 0000000001a8d000 CR4: 00000000001407e0
<4>DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<4>DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
<4>Process qedf_11_ll2 (pid: 1485, threadinfo ffff881068a80000, task ffff881068a70040)
<4>Stack:
<4> ffff88106ef00090 0000000300000001 ffff881068a83d90 ffff88106bf42de0
<4><d> 0000000000000286 ffff88106bf42dd8 ffff88106bf40a50 0000000000000002
<4><d> ffff881068a83dc0 ffffffff810634c7 ffff881000000003 000000000000000b
<4>Call Trace:
<4> [<ffffffff810634c7>] complete+0x47/0x60
<4> [<ffffffffa01d37e7>] qedf_fip_recv+0x1c7/0x450 [qedf]
<4> [<ffffffffa01cb3cb>] qedf_ll2_recv_thread+0x33b/0x510 [qedf]
<4> [<ffffffffa01cb090>] ? qedf_ll2_recv_thread+0x0/0x510 [qedf]
<4> [<ffffffff810a662e>] kthread+0x9e/0xc0
<4> [<ffffffff8100c28a>] child_rip+0xa/0x20
<4> [<ffffffff810a6590>] ? kthread+0x0/0xc0
<4> [<ffffffff8100c280>] ? child_rip+0x0/0x20
<4>Code: 41 56 41 55 41 54 53 48 83 ec 18 0f 1f 44 00 00 89 75 cc 89 55 c8 4c 8d 6f 08 48 8b 57 08 41 89 cf 4d 89 c6 48 8d 42 e8 49 39 d5 <48> 8b 58 18 74 3f 48 83 eb 18 eb 0a 0f 1f 00 48 89 d8 48 8d 5a
<1>RIP  [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4> RSP <ffff881068a83d50>
<4>CR2: 0000000000000000

Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sr: Sanity check returned mode data

Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.

Cc: <stable@vger.kernel.org>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sd: Consider max_xfer_blocks if opt_xfer_blocks is unusable

If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.

[mkp: tweaked to avoid setting rw_max twice and added typecast]

Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ca369d51b3e ("block/sd: Fix device-imposed transfer length limits")
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: remove the duplicated checking for supporting clkscaling

There are same conditions for checking whether supporting clkscaling or
not. When ufshcd is supporting clkscaling, active_reqs should be
decreased by one.

[mkp: addressed comment from Bartlomiej]

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: fix building without debugfs support

On a randconfig build without CONFIG_SCSI_LPFC_DEBUG_FS, I ran into
multiple compile failures:

drivers/scsi/lpfc/lpfc_debugfs.h: In function 'lpfc_debug_dump_wq':
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: error: 'DUMP_FCP' undeclared (first use in this function); did you mean 'DUMP_VAR'?
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: note: each undeclared identifier is reported only once for each function it appears in
drivers/scsi/lpfc/lpfc_debugfs.h:408:22: error: 'DUMP_NVME' undeclared (first use in this function); did you mean 'DUMP_NONE'?
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_ls_rsp_cmp':
drivers/scsi/lpfc/lpfc_nvmet.c:109:2: error: implicit declaration of function 'lpfc_nvmeio_data'; did you mean 'lpfc_mem_free'? [-Werror=implicit-function-declaration]
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_fcp_op':
drivers/scsi/lpfc/lpfc_nvmet.c:523:10: error: unused variable 'id' [-Werror=unused-variable]

They are all trivial to fix, so I'm doing it in a combined patch here.

Fixes: 1d9d5a9879ad ("scsi: lpfc: refactor debugfs queue dump routines")
Fixes: bd2cdd5e400f ("scsi: lpfc: NVME Initiator: Add debugfs support")
Fixes: 2b65e18202fd ("scsi: lpfc: NVME Target: Add debugfs support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix PT2PT PRLI reject

lpfc cannot establish connection with targets that send PRLI in P2P
configurations.

If lpfc rejects a PRLI that is sent from a target the target will not
resend and will reject the PRLI send from the initiator.

[mkp: applied by hand]

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: fix volume offline state

In a previous patch a hpsa_scsi_dev_t.volume_offline update line has
been removed, so let us put it back..

Fixes: 85b29008d8 (hpsa: update check for logical volume status)
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: libsas: fix ata xfer length

The total ata xfer length may not be calculated properly, in that we do
not use the proper method to get an sg element dma length.

According to the code comment, sg_dma_len() should be used after
dma_map_sg() is called.

This issue was found by turning on the SMMUv3 in front of the hisi_sas
controller in hip07. Multiple sg elements were being combined into a
single element, but the original first element length was being use as
the total xfer length.

Cc: <stable@vger.kernel.org>
Fixes: ff2aeb1eb64c8a4770a6 ("libata: convert to chained sg")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_dh_alua: Warn if the first argument of alua_rtpg_queue() is NULL

Callers must provide a valid port group to alua_rtpg_queue().  Issue a
kernel warning if that is not the case.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_dh_alua: Ensure that alua_activate() calls the completion function

Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function
either returns an error code or calls the completion function. Make
alua_activate() call the completion function even if scsi_device_get()
fails.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Cc: <stable@vger.kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_dh_alua: Check scsi_device_get() return value

Do not queue ALUA work nor call scsi_device_put() if the
scsi_device_get() call fails. This patch fixes the following crash:

general protection fault: 0000 [#1] SMP
RIP: 0010:scsi_device_put+0xb/0x30
Call Trace:
 scsi_disk_put+0x2d/0x40
 sd_release+0x3d/0xb0
 __blkdev_put+0x29e/0x360
 blkdev_put+0x49/0x170
 dm_put_table_device+0x58/0xc0 [dm_mod]
 dm_put_device+0x70/0xc0 [dm_mod]
 free_priority_group+0x92/0xc0 [dm_multipath]
 free_multipath+0x70/0xc0 [dm_multipath]
 multipath_dtr+0x19/0x20 [dm_multipath]
 dm_table_destroy+0x67/0x120 [dm_mod]
 dev_suspend+0xde/0x240 [dm_mod]
 ctl_ioctl+0x1f5/0x520 [dm_mod]
 dm_ctl_ioctl+0xe/0x20 [dm_mod]
 do_vfs_ioctl+0x8f/0x700
 SyS_ioctl+0x3c/0x70
 entry_SYSCALL_64_fastpath+0x18/0xad

Fixes: commit 03197b61c5ec ("scsi_dh_alua: Use workqueue for RTPG")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Cc: <stable@vger.kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sg: check length passed to SG_NEXT_CMD_LEN

The user can control the size of the next command passed along, but the
value passed to the ioctl isn't checked against the usable max command
size.

Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Chang <dpf@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufshcd-platform: remove the useless cast in ERR_PTR/IS_ERR

IS_ERR and ERR_PTR already forcefully cast their argument, hence there
is no need for additional (complex) casting.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: Add PCI device-ID for QL41xxx adapters.

Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Fix potential null access

Currently, command threads fails to return ioctls commands for older
controller versions, since it returns when all the fibs have been
allocated. Another issue is even all the fibs have not been allocated,
the correct allocated fibs is not updated nor freed.

Fixes: 113156bcea9ef1e6 (scsi: aacraid: Reworked aac_command_thread)
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix crash in qla2xxx_eh_abort on bad ptr

After a Qlogic card breaks when initializing (test case), the system can
crash in qla2xxx_eh_abort if processing anything but a scsi command type
srb.

Fixes: 1535aa75a3d8 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-By: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Finalize Kconfig options for nvme

Reviewing the result of what was just added for Kconfig, we made a poor
choice. It worked well for full kernel builds, but not so much for how
it would be deployed on a distro.

Here's the final result:
- lpfc will compile in NVME initiator and/or NVME target support based
  on whether the kernel has the corresponding subsystem support.
  Kconfig is not used to drive this specifically for lpfc.
- There is a module parameter, lpfc_enable_fc4_type, that indicates
  whether the ports will do FCP-only or FCP & NVME (NVME-only not yet
  possible due to dependency on fc transport). As FCP & NVME divvys up
  exchange resources, and given NVME will not be often initially, the
  default is changed to FCP only.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: don't check unsigned type for a negative value

Fix compilation warning:

drivers/scsi/ufs/ufshcd.c:7645:13: warning: comparison of unsigned
expression < 0 is always false [-Wtype-limits]
if ((value < UFS_PM_LVL_0) || (value >= UFS_PM_LVL_MAX))

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: do not timeout reset operations

Resets can take longer than DEFAULT_TIMEOUT.

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: limit outstanding rescans

Avoid rescan storms. No need to queue another if one is pending.

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: update check for logical volume status

 - Add in a new case for volume offline. Resolves internal testing bug
   for multilun array management.
 - Return correct status for failed TURs.

Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: Driver version upgrade

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: raid6 also require cpuSel check same as raid5

Without this fix, raid6 performance will not be optimal.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: add correct return type check for ldio hint logic for raid1

Return value check of atomic_dec_if_positive is required as it returns
old value minus one.  Without this fix, driver will send small ios to
firmware path and that will be a performance issue.

Not critical, but good to have r1_ldio_hint as default value in sdev
private.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: megaraid_sas: enable intx only if msix request fails

Without this fix, driver will enable INTx Interrupt pin even though
MSI-x vectors are enabled. See below lspci output. DisINTx is unset for
MSIx setup.

lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-

After applying this fix, driver will enable INTx Interrupt pin only if
Legacy interrupt method is required.  See below lspci output. DisINTx is
set for MSIx setup.  lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Add shutdown method for kexec

We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.

Cc: <stable@vger.kernel.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: storvsc: Workaround for virtual DVD SCSI version

Hyper-V host emulation of SCSI for virtual DVD device reports SCSI
version 0 (UNKNOWN) but is still capable of supporting REPORTLUN.

Without this patch, a GEN2 Linux guest on Hyper-V will not boot 4.11
successfully with virtual DVD ROM device. What happens is that the SCSI
scan process falls back to doing sequential probing by INQUIRY.  But the
storvsc driver has a previous workaround that masks/blocks all errors
reports from INQUIRY (or MODE_SENSE) commands.  This workaround causes
the scan to then populate a full set of bogus LUN's on the target and
then sends kernel spinning off into a death spiral doing block reads on
the non-existent LUNs.

By setting the correct blacklist flags, the target with the DVD device
is scanned with REPORTLUN and that works correctly.

Patch needs to go in current 4.11, it is safe but not necessary in older
kernels.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: revise version number to 11.2.0.10

Revise lpfc version number to 11.2.0.10

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: code cleanups in NVME initiator discovery

This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105665.html

The issues are:

drivers/scsi/lpfc/lpfc_ct.c:943 lpfc_cmpl_ct_cmd_gft_id()
error: we previously assumed 'ndlp' could be null (see line 928)

Action: moved under if check

drivers/scsi/lpfc/lpfc_nvmet.c:1694 lpfc_nvmet_unsol_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1690)

Action: conditionalized arg in printf stmt

drivers/scsi/lpfc/lpfc_nvmet.c:1792 lpfc_nvmet_sol_fcp_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1788)

Action: conditionalized arg in printf stmt

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: code cleanups in NVME initiator base

This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105663.html

The issues are:

drivers/scsi/lpfc/lpfc_hbadisc.c:316 lpfc_dev_loss_tmo_handler()
warn: we tested 'vport->load_flag & 2' before and it was 'false'

Action: removed item from test

drivers/scsi/lpfc/lpfc_hbadisc.c:701 lpfc_work_done()
warn: test_bit() takes a bit number

Action: changed definition so bit number

drivers/scsi/lpfc/lpfc_hbadisc.c:2206 lpfc_mbx_cmpl_fcf_scan_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2582 lpfc_mbx_cmpl_fcf_rr_read_fcf_rec()
error: uninitialized symbol 'vlan_id'.
drivers/scsi/lpfc/lpfc_hbadisc.c:2683 lpfc_mbx_cmpl_read_fcf_rec() error:
uninitialized symbol 'vlan_id'.

Action: initilized value

drivers/scsi/lpfc/lpfc_hbadisc.c:4025 lpfc_register_remote_port()
error: we previously assumed 'rdata' could be null (see line 4023)

Action: refactored check block

drivers/scsi/lpfc/lpfc_hbadisc.c:4613 lpfc_sli4_dequeue_nport_iocbs()
error: double unlock 'irq:'

Action: removed inner irq reference

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: correct rdp diag portnames

NVME merge reverted diag port names to the physical port.
They should be the vport.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: remove dead sli3 nvme code

Remove nvme teardown calls that should not be there on sli3 devices

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: correct double print

Correct a merge error that had debug data printed twice for the
same element

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Rename LPFC_MAX_EQ_DELAY to LPFC_MAX_EQ_DELAY_EQID_CNT

Without apriori understanding of what the define is, the name gives
a very different impression of what it is (a max delay value
for an EQ).  Rename the define so it reflects what it is: the number
of EQ IDs that can be set in one instance of the MODIFY_EQ_DELAY
mbx command.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Rework lpfc Kconfig for NVME options

Reworked Kconfig so that lfpc only requires the scsi stack.
NVME Initiator and NVME Target support can be enabled if
the other NVMe subsystems have been enabled.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: add transport eh_timed_out reference

Christoph's prior patch missed the template for the sli3 adapters,
which is now the "no host reset" template. Add the transport
eh_timed_out handler to the no host reset template

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix eh_deadline setting for sli3 adapters.

A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state.  With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.

This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: add NVME exchange aborts

previous code did little more than log a message.

This patch adds abort path support, modeled after the SCSI code paths.
Currently addresses only the initiator path. Target path under
development, but stubbed out.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix nvme allocation bug on failed nvme_fc_register_localport

nvme bufs get allocated even when the registration fails.
Move allocation into the rsgistration success path.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix IO submission if WQ is full

For both initiator and target: if WQ is full, return -EBUSY.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix NVME CMD IU byte swapped word 1 problem

Word 1 in NVME CMD IU appears byte swapped from value placed in WQE
Should be Big Endian value in WQE word 16

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix RCTL value on NVME LS request and response

NVME LS requests and responses had wrong R_CTL values.
Use the FC4 ELS Request and Response defines (defines badly
named, they are FC4 LS's) instead of the base ELS values.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix crash during Hardware error recovery on SLI3 adapters

if REG_VPI fails, the driver was incorrectly issuing INIT_VFI
(a SLI4 command) on a SLI3 adapter.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: fix missing spin_unlock on sql_list_lock

From: Colin Ian King <colin.king@canonical.com>

In the case where sglq is null, the current code just returns without
unlocking the spinlock sql_list_lock. Fix this by breaking out of the
while loop and the exit path will then unlock and return NULL as was
the original intention.

Detected by CoverityScan, CID#1411635 ("Missing unlock")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: don't dereference dma_buf->iocbq before null check

From: Colin Ian King <colin.king@canonical.com>

dma_buf->iocbq is being dereferenced immediately before it is
being null checked, so we have a potential null pointer dereference
bug.  Fix this by only dereferencing it only once we have passed
a null check on the pointer.

Detected by CoverityScan, CID#1411652 ("Dereference before null check")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: sanity check hrq is null before dereferencing it

From: Colin Ian King <colin.king@canonical.com>

The sanity check for hrq should be moved to before the deference
of hrq to ensure we don't perform a null pointer deference.

Detected by CoverityScan, CID#1411650 ("Dereference before null check")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: remove redundant assignment of sgel

From: Colin Ian King <colin.king@canonical.com>

In the NVMET_FCOP_RSP case, sgel is assigned but never used and
hence is redundant and can be removed.

Detected by CoverityScan, CID#1411658 ("Unused value")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: replace init_timer by setup_timer

This patch shortens every init_timer in lpfc module followed by function
and data assignment using setup_timer.  This is purely cleanup patch, it
does not add new functionality nor remove any existing functionality.

An init_timer call in this form:

    init_timer(&vport->fc_disctmo);
    vport->fc_disctmo.function = lpfc_disc_timeout;
    vport->fc_disctmo.data = vport;

is shortened to:

    setup_timer(&vport->fc_disctmo, lpfc_disc_timeout, vport);

It increases readability and reduces chances of mistakes done by
developers.

Signed-off-by: Tomas Jasek <tomsik68@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Use vsprintf extension %pad

Using %llx for a dma_addr_t can lead to format/argument mismatches.  Use
%pad and the address of the dma_addr_t instead.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Fix defective logging format and argument mismatches

Add __printf compiler verification of format and arguments.  Fix
fallout.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: vmw_pvscsi: handle the return value from pci_alloc_irq_vectors correctly

It returns the number of vectors allocated when successful, so check for
a negative error only.

Fixes: 2e48e349 ("scsi: vmw_pvscsi: switch to pci_alloc_irq_vectors")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Loïc Yhuel <loic.yhuel@gmail.com>
Tested-by: Loïc Yhuel <loic.yhuel@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix ql_dump_buffer

Recent printk changes for KERN_CONT cause this logging to be defectively
emitted on multiple lines.  Fix it.

Also reduces object size a trivial amount.

$ size drivers/scsi/qla2xxx/qla_dbg.o*
   text    data     bss     dec     hex filename
  39125       0       0   39125    98d5 drivers/scsi/qla2xxx/qla_dbg.o.new
  39164       0       0   39164    98fc drivers/scsi/qla2xxx/qla_dbg.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Fix typo in blink status

The return status of the adapter check on KERNEL_PANIC is supposed to be
the upper 16 bits of the OMR status register.

Fixes: c421530bf848604e (scsi: aacraid: Reorder Adpater status check)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: fix build error without DEBUG_FS

Without CONFIG_DEBUG_FS, we run into a link error:

drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_poll':
qedi_iscsi.c:(.text.qedi_ep_poll+0x134): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_disconnect':
qedi_iscsi.c:(.text.qedi_ep_disconnect+0x36c): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_connect':
qedi_iscsi.c:(.text.qedi_ep_connect+0x350): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_fw.o: In function `qedi_tmf_work':
qedi_fw.c:(.text.qedi_tmf_work+0x3b4): undefined reference to `do_not_recover'

This defines the symbol as a constant in this case, as there is no way to
set it to anything other than zero without DEBUG_FS. In addition, I'm renaming
it to qedi_do_not_recover in order to put it into a driver specific namespace,
as "do_not_recover" is a really bad name for a kernel-wide global identifier
when it is used only in one driver.

Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Avoid sleeping in interrupt context

Commit 669f044170d8 ("scsi: srp_transport: Move queuecommand() wait code
to SCSI core") can make scsi_internal_device_block() sleep.  However,
the mpt3sas driver can call this function from an interrupt
handler. Hence add a second argument to scsi_internal_device_block()
that restores the old behavior of this function for the mpt3sas handler.

The call chain that triggered an "IRQ handler enabled interrupts"
complaint is as follows:

_base_interrupt()
-> _base_async_event()
   -> mpt3sas_scsih_event_callback()
      -> _scsih_check_topo_delete_events()
         -> _scsih_block_io_to_children_attached_directly()
            -> _scsih_block_io_device()
               -> _scsih_internal_device_block()
                  -> scsi_internal_device_block()

Reported-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Omar Sandoval <osandov@osandov.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <stable@vger.kernel.org> # v4.10+
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sd: Check for unaligned partial completion

Commit <f2e767bb5d6e> ("mpt3sas: Force request partial completion
alignment") was not considering the case of commands not operating on
logical block size units (e.g. REQ_OP_ZONE_REPORT and its 64B aligned
partial replies). In this case, forcing alignment of resid to the device
logical block size can break the command result, e.g. in the case of
REQ_OP_ZONE_REPORT, the exact number of zone reported by the device.

Move the partial completion alignement check of mpt3sas to a generic
implementation in sd_done(). The check is added within the default
section of the initial req_op() switch case so that the report and reset
zone commands are ignored. In addition, as sd_done() is not called for
passthrough requests, resid corrections are not done as intended by the
initial mpt3sas patch.

Fixes: f2e767bb5d6e ("mpt3sas: Force request partial completion alignment")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Factor out ufshcd_read_desc_param

Since in UFS 2.1 specification some of the descriptor lengths differs
from 2.0 specification and some devices, which are reporting spec
version 2.0 have different descriptor lengths we can not rely on
hardcoded values taken from 2.0 specification. This patch introduces
reading these lengths per each device from descriptor headers at probe
time to ensure their correctness.

Signed-off-by: Michal' Potomski <michalx.potomski@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: libiscsi: add lock around task lists to fix list corruption regression

There's a rather long standing regression from the commit "libiscsi:
Reduce locking contention in fast path"

Depending on iSCSI target behavior, it's possible to hit the case in
iscsi_complete_task where the task is still on a pending list
(!list_empty(&task->running)).  When that happens the task is removed
from the list while holding the session back_lock, but other task list
modification occur under the frwd_lock.  That leads to linked list
corruption and eventually a panicked system.

Rather than back out the session lock split entirely, in order to try
and keep some of the performance gains this patch adds another lock to
maintain the task lists integrity.

Major enterprise supported kernels have been backing out the lock split
for while now, thanks to the efforts at IBM where a lab setup has the
most reliable reproducer I've seen on this issue.  This patch has been
tested there successfully.

Signed-off-by: Chris Leech <cleech@redhat.com>
Fixes: 659743b02c41 ("[SCSI] libiscsi: Reduce locking contention in fast path")
Reported-by: Prashantha Subbarao <psubbara@us.ibm.com>
Reviewed-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: fix missing return error code check on call to qedi_setup_int

The call to qedi_setup_int is not updating the return code rc yet rc is
being checked for an error. Fix this by assigning rc to the return code
from the call to qedi_setup_int.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: Fix memory leak in tmf response processing.

Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: remove redundant zero check on ret

The check for ret being zero is redundant as a few statements earlier we
break out of the while loop if ret is non-zero.  Thus we can remove the
zero check and also the dead-code non-zero case too.

Detected by CoverityScan, CID#1411632 ("Logically Dead Code")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: use proper format string for dma_addr_t

dma_addr_t may be either u32 or u64, depending on the kernel configuration,
and we get a warning for the 32-bit case:

drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_ls_req':
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 11 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 12 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_ls_abort':
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 11 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
drivers/scsi/lpfc/lpfc_logmsg.h:52:52: error: format '%llu' expects argument of type 'long long unsigned int', but argument 12 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]

printk has a special "%pad" format string that passes the dma address by
reference to solve this problem.

Fixes: 01649561a8b4 ("scsi: lpfc: NVME Initiator: bind to nvme_fc api")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: use div_u64 for 64-bit division

The new debugfs output causes a link error on 32-bit architectures:

ERROR: "__aeabi_uldivmod" [drivers/scsi/lpfc/lpfc.ko] undefined!

This code is not performance critical, so we can simply use div_u64().

[mkp: fixed up whitespace]

Fixes: bd2cdd5e400f ("scsi: lpfc: NVME Initiator: Add debugfs support")
Fixes: 2b65e18202fd ("scsi: lpfc: NVME Target: Add debugfs support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m

The mac_scsi driver still gets disabled when SCSI=m. This should have
been fixed back when I enabled the tristate but I didn't see the bug.

Fixes: 6e9ae6d560e1 ("[PATCH] mac_scsi: Add module option to Kconfig")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cciss: correct check map error.

Remove device driver failed to check map error messages

Reported-by: Johnny Bieren <jbieren@redhat.com>
Tested-by: Johnny Bieren <jbieren@redhat.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"

Trivial fix to spelling mistake in pr_err message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Fixed expander hotplug for SMART family

Current driver Hotplug processing code skips over Enclosure channel,
therefore any addition/removal of expander enclosure is not processed.
Additionally device addition code relies on older device type, which
prevents the hotplug of adapter expanders.

Fixed by removing code that skips over Enclosure channels and using the
latest device type for addition or removal or enclosure expanders.

Fixes: 6223a39fe6fbbeef (scsi: aacraid: Added support for hotplug)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: switch to pci_alloc_irq_vectors

Cleanup the MSI-X handling allowing us to use the PCI-layer provided
vector allocation.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: fixup compilation warning about atomic_t usage

Based on an original patch by Hannes Reinecke.

The driver didn't follow the atomic_t vs refcount_t change, and anyway
one should be using kref_read() instead of accessing the counter inside
an kref.

Fixes: 61d8658b4a435e ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.)
Cc: Hannes Reinecke <hare@suse.de>
Cc: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Dupuis, Chad <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: remove scsi_execute_req_flags

And switch all callers to use scsi_execute instead.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: merge __scsi_execute into scsi_execute

All but one caller want the decoded sense header, so offer the existing
__scsi_execute helper as the public scsi_execute API to simply the
callers.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: simplify scsi_execute_req_flags

Add a sshdr argument to __scsi_execute so that we can decode the sense
data directly into the sense header instead of needing a copy of it.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: make the sense header argument to scsi_test_unit_ready mandatory

It's a tiny structure that can be allocated on the stack, don't
complicate the code by making it optional.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sd: improve TUR handling in sd_check_events

Remove bogus evaluations of retval and sshdr when the device is offline,
and fix a possible NULL pointer dereference by allocating the 8 byte
sized sense header on stack.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: always zero sshdr in scsi_normalize_sense

This gives us a clear state even if a command didn't return sense data.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_dh_emc: return success in clariion_std_inquiry()

We accidentally return an uninitialized variable on success.

Fixes: b6ff1b14cdf4 ("[SCSI] scsi_dh: Update EMC handler")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fix memory leak of sdpk on when gd fails to allocate

On an allocation failure of gd, the current exit path is via
out_free_devt which leaves sdpk still allocated and hence it gets
leaked. Fix this by correcting the order of resource free'ing with a
change in the error exit path labels.

Detected by CoverityScan, CID#1399519 ("Resource Leak")

Fixes: 0dba1314d4f81115dc ("scsi, block: fix duplicate bdi name registration crashes")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sd: make sd_devt_release() static

Fixes the following sparse warning:

drivers/scsi/sd.c:3087:6: warning:
 symbol 'sd_devt_release' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.

The QLogic FastLinQ Driver for FCoE (qedf) is the FCoE specific module
for 41000 Series Converged Network Adapters by QLogic. This patch
consists of following changes:

- MAINTAINERS Makefile and Kconfig changes for qedf
- PCI driver registration
- libfc/fcoe host level initialization
- SCSI host template initialization and callbacks
- Debugfs and log level infrastructure
- Link handling
- Firmware interface structures
- QED core module initialization
- Light L2 interface callbacks
- I/O request initialization
- Firmware I/O completion handling
- Firmware ELS request/response handling
- FIP request/response handled by the driver itself

Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@cavium.com>
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix Regression introduced by pci_alloc_irq_vectors_affinity call.

For target mode, we need to increase minimum vectors value by one to
account for ATIO queue.

Following stack trace will be seen

Call Trace:
qla24xx_config_rings+0x15a/0x230 [qla2xxx]
qla2x00_init_rings+0x1a1/0x3a0 [qla2xxx]
qla2x00_restart_isp+0x5c/0x120 [qla2xxx]
qla2x00_abort_isp+0x138/0x430 [qla2xxx]
? __schedule+0x260/0x580
qla2x00_do_dpc+0x3bc/0x920 [qla2xxx]
? qla2x00_relogin+0x290/0x290 [qla2xxx]
? schedule+0x3a/0xa0
? qla2x00_relogin+0x290/0x290 [qla2xxx]
kthread+0x103/0x140
? __kthread_init_worker+0x40/0x40
ret_from_fork+0x29/0x40

RIP: qlt_24xx_config_rings+0x6c/0x90

[mkp: fixed Fixes: hash]

Cc: <stable@vger.kernel.org>
Fixes: 17e5fc58588b ("scsi: qla2xxx: fix MSI-X vector affinity")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix response queue count for Target mode.

Target mode initialization was not calculating response queue values
correctly resulting into one less MSI-X vector.

[mkp: fixed Fixes: hash]

Cc: <stable@vger.kernel.org>
Fixes: 093df73771ba ("scsi: qla2xxx: Fix Target mode handling with Multiqueue changes.")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Cleaned up queue configuration code.

This patch cleaned up queue configuration code, such that once
initialized, we should not touch msix_count value.  This will prevent
incorrect numbers of MSI-X vectors requested while performing target
mode configuration.

[mkp: fixed Fixes: hash]

Cc: <stable@vger.kernel.org>
Fixes: d74595278f4a ("scsi: qla2xxx: Add multiple queue pair functionality.")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: add missing Kconfig NVME dependencies

Add missing Kconfig NVME dependencies.

Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Update lpfc version to 11.2.0.7

Update lpfc version to 11.2.0.7

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Update copyrights

Update copyrights to 2017 for all files touched in this patch set

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Target: Add debugfs support

NVME Target: Add debugfs support

Adds debugfs snippets to cover the new NVME target functionality

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Target: bind to nvmet_fc api

NVME Target: Tie in to NVME Fabrics nvmet_fc LLDD target api

Adds the routines to:
- register and deregister the FC port as a nvmet-fc targetport
- binding of nvme queues to adapter WQs
- receipt and passing of NVME LS's to transport, sending transport response
- receipt of NVME FCP CMD IUs, processing FCP target io data transmission
  commands; transmission of FCP io response
- Abort operations for tgt io exchanges

[mkp: fixed space at end of file warning]

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Target: Merge into FC discovery

NVME Target: Merge into FC discovery

Adds NVME PRLI handling and Nameserver registrations for NVME

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Target: Receive buffer updates

NVME Target: Receive buffer updates

Allocates buffer pools and configures adapter interfaces to handle
receive buffer (asynchronous FCP CMD ius, first burst data)
from the adapter. Splits by protocol, etc.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Target: Base modifications

NVME Target: Base modifications

This set of patches adds the base modifications for NVME target support

The base modifications consist of:
- Additional module parameters or configuration tuning
- Enablement of configuration mode for NVME target. Ties into the
  queueing model put into place by the initiator basemods patches.
- Target-specific buffer pools, dma pools, sgl pools

[mkp: fixed space at end of file]

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Initiator: Add debugfs support

NVME Initiator: Add debugfs support

Adds debugfs snippets to cover the new NVME initiator functionality

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Initiator: bind to nvme_fc api

NVME Initiator: Tie in to NVME Fabrics nvme_fc LLDD initiator api

Adds the routines to:
- register and deregister the FC port as a nvme-fc initiator localport
- register and deregister remote FC ports as a nvme-fc remoteport
- binding of nvme queues to adapter WQs
- send/perform NVME LS's
- send/perform NVME FCP initiator io operations

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Initiator: Merge into FC discovery

NVME Initiator: Merge into FC discovery

Adds NVME PRLI support and Nameserver registrations and Queries for NVME

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: NVME Initiator: Base modifications

NVME Initiator: Base modifications

This patch adds base modifications for NVME initiator support.

The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
  rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
   SCSI initiator only; NVME initiator only; NVME target only; and
   SCSI and NVME initiator.
   The configuration mode drives overall adapter configuration,
   offloads enabled, and resource splits.
   NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
  - Exchange resources are split by protocol; Obviously, if only
     1 mode, then no split occurs. Default is 50/50. module attribute
     allows tuning.
  - Pools and config parameters are separated per-protocol
  - Each protocol has it's own set of queues, but share interrupt
    vectors.
     SCSI:
       SLI3 devices have few queues and the original style of queue
         allocation remains.
       SLI4 devices piggy back on an "io-channel" concept that
         eventually needs to merge with scsi-mq/blk-mq support (it is
 underway).  For now, the paradigm continues as it existed
 prior. io channel allocates N msix and N WQs (N=4 default)
 and either round robins or uses cpu # modulo N for scheduling.
 A bunch of module parameters allow the configuration to be
 tuned.
     NVME (initiator):
       Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
         gets)
       Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
         modulo msix vector count basis.
       Module parameters exist to cap/control the config if desired.
  - Each protocol has its own buffer and dma pools.

I apologize for the size of the patch.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: refactor debugfs queue dump routines

Create common wq, cq, eq, rq dump functions

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: refactor debugfs queue prints

Create common wq, cq, eq, rq print functions

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>