arm64: smp: Handle errors reported by the firmware

[ Upstream commit f357b3a7e17af7736d67d8267edc1ed3d1dd9391 ]

The __cpu_up() routine ignores the errors reported by the firmware
for a CPU bringup operation and looks for the error status set by the
booting CPU. If the CPU never entered the kernel, we could end up
in assuming stale error status, which otherwise would have been
set/cleared appropriately by the booting CPU.

Reported-by: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: mm: Prevent mismatched 52-bit VA support

[ Upstream commit a96a33b1ca57dbea4285893dedf290aeb8eb090b ]

For cases where there is a mismatch in ARMv8.2-LVA support between CPUs
we have to be careful in allowing secondary CPUs to boot if 52-bit
virtual addresses have already been enabled on the boot CPU.

This patch adds code to the secondary startup path. If the boot CPU has
enabled 52-bit VAs then ID_AA64MMFR2_EL1 is checked to see if the
secondary can also enable 52-bit support. If not, the secondary is
prevented from booting and an error message is displayed indicating why.

Technically this patch could be implemented using the cpufeature code
when considering 52-bit userspace support. However, we employ low level
checks here as the cpufeature code won't be able to run if we have
mismatched 52-bit kernel va support.

Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

parisc: Fix HP SDC hpa address output

[ Upstream commit c4bff35ca1bfba886da6223c9fed76a2b1382b8e ]

Show the hpa address of the HP SDC instead of a hashed value, e.g.:
HP SDC: HP SDC at 0xf0201000, IRQ 23 (NMI IRQ 24)

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

parisc: Fix serio address output

[ Upstream commit 785145171d17af2554128becd6a7c8f89e101141 ]

We want the hpa addresses printed in the serio modules, not some
virtual ioremap()ed address, e.g.:

 serio: gsc-ps2-keyboard port at 0xf0108000 irq 22 @ 2:0:11
 serio: gsc-ps2-mouse port at 0xf0108100 irq 22 @ 2:0:12

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx53-voipac-dmm-668: Fix memory node duplication

[ Upstream commit 998a84c27a7f3f9133d32af64e19c05cec161a1a ]

imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.

Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed

[ Upstream commit 7c41ea57beb2aee96fa63091a457b1a2826f3c42 ]

If debugging on i.MX is enabled DEBUG_IMX_UART_PORT defines which UART
is used for the debug output. If however debugging is off don't only
hide the then unused config item but drop it completely by using a
dependency instead of a conditional prompt.

This fixes DEBUG_IMX_UART_PORT being present in the kernel config even
if DEBUG_LL is disabled.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: Fix up SQ201 flash access

[ Upstream commit d88b11ef91b15d0af9c0676cbf4f441a0dff0c56 ]

This sets the partition information on the SQ201 to be read
out from the RedBoot partition table, removes the static
partition table and sets our boot options to mount root from
/dev/mtdblock2 where the squashfs+JFFS2 resides.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Fix dif and first burst use in write commands

[ Upstream commit 7c4042a4d0b7532cfbc90478fd3084b2dab5849e ]

When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.

Correct the wqe initializaton when both dif and first burst are used.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Fix kernel Oops due to null pring pointers

[ Upstream commit 5a9eeff57f340238c39c95d8e7e54c96fc722de7 ]

Driver is hitting null pring pointers in lpfc_do_work().

Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.

Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: bcm-iproc: Prevent unloading the driver module while in use

[ Upstream commit 24906a41eecb73d51974ade0847c21e429beec60 ]

The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.

Fixes: daa5abc41c80 ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

block: drbd: remove a stray unlock in __drbd_send_protocol()

[ Upstream commit 8e9c523016cf9983b295e4bc659183d1fa6ef8e0 ]

There are two callers of this function and they both unlock the mutex so
this ends up being a double unlock.

Fixes: 44ed167da748 ("drbd: rcu_read_lock() and rcu_dereference() for tconn->net_conf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: fix station inactive_time shortly after boot

[ Upstream commit 285531f9e6774e3be71da6673d475ff1a088d675 ]

In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).

 # iw wlan0 station get fc:ec:da:64:a6:dd
 Station fc:ec:da:64:a6:dd (on wlan0)
inactive time: 4294894049 ms
.
.
connected time: 70 seconds

Fix by returning last_rx if last_ack == 0.

Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: return -EINVAL if given fsc mount option on kernel w/o support

[ Upstream commit ff29fde84d1fc82f233c7da0daa3574a3942bec7 ]

If someone requests fscache on the mount, and the kernel doesn't
support it, it should fail the mount.

[ Drop ceph prefix -- it's provided by pr_err. ]

Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: bcmgenet: reapply manual settings to the PHY

[ Upstream commit 0686bd9d5e6863f60e4bb1e78e6fe7bb217a0890 ]

The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.

This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.

Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scripts/gdb: fix debugging modules compiled with hot/cold partitioning

[ Upstream commit 8731acc5068eb3f422a45c760d32198175c756f8 ]

gcc's -freorder-blocks-and-partition option makes it group frequently
and infrequently used code in .text.hot and .text.unlikely sections
respectively.  At least when building modules on s390, this option is
used by default.

gdb assumes that all code is located in .text section, and that .text
section is located at module load address.  With such modules this is no
longer the case: there is code in .text.hot and .text.unlikely, and
either of them might precede .text.

Fix by explicitly telling gdb the addresses of code sections.

It might be tempting to do this for all sections, not only the ones in
the white list.  Unfortunately, gdb appears to have an issue, when
telling it about e.g. loadable .note.gnu.build-id section causes it to
think that non-loadable .note.Linux section is loaded at address 0,
which in turn causes NULL pointers to be resolved to bogus symbols.  So
keep using the white list approach for the time being.

Link: http://lkml.kernel.org/r/20191028152734.13065-1-iii@linux.ibm.com
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

watchdog: meson: Fix the wrong value of left time

[ Upstream commit 2c77734642d52448aca673e889b39f981110828b ]

The left time value is wrong when we get it by sysfs. The left time value
should be equal to preset timeout value minus elapsed time value. According
to the Meson-GXB/GXL datasheets which can be found at [0], the timeout value
is saved to BIT[0-15] of the WATCHDOG_TCNT, and elapsed time value is saved
to BIT[16-31] of the WATCHDOG_TCNT.

[0]: http://linux-meson.com

Fixes: 683fa50f0e18 ("watchdog: Add Meson GXBB Watchdog Driver")
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_irq_offload_fifo(): continue on error

[ Upstream commit 1f7f504dcd9d1262437bdcf4fa071e41dec1af03 ]

In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.

If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.

In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.

Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.

Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.

With this patch the loop is left in case of empty FIFO, but not on
errors.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_irq_offload_timestamp(): continue on error

[ Upstream commit c2a9f74c9d18acfdcabd3361adc7eac82c537a66 ]

In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.

However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.

Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.

Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_offload_one(): use ERR_PTR() to propagate error value in case of errors

[ Upstream commit d763ab3044f0bf50bd0e6179f6b2cf1c125d1d94 ]

Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.

However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.

This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error

All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_offload_one(): increment rx_fifo_errors on queue overflow or OOM

[ Upstream commit 4e9016bee3bf0c24963097edace034ff205b565c ]

If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.

This patch adds the incrementing of the rx_fifo_errors statistics counter.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_offload_one(): do not increase the skb_queue beyond skb_queue_len_max

[ Upstream commit a2dc3f5e1022a5ede8af9ab89a144f1e69db8636 ]

The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.

Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.

This patch limits the rx-offload skb_queue length to skb_queue_len_max.

Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: rx-offload: can_rx_offload_queue_tail(): fix error handling, avoid skb mem leak

[ Upstream commit 6caf8a6d6586d44fd72f4aa1021d14aa82affafb ]

If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.

This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.

The return value is adjusted to -ENOBUFS to better reflect the actual
problem.

The device stats handling is left to the caller.

Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: c_can: D_CAN: c_can_chip_config(): perform a sofware reset on open

[ Upstream commit 23c5a9488f076bab336177cd1d1a366bd8ddf087 ]

When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.

According to [1], the C_CAN module doesn't have the software reset.

[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf

Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: peak_usb: report bus recovery as well

[ Upstream commit 128a1b87d3ceb2ba449d5aadb222fe22395adeb0 ]

While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.

Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.

Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bridge: ebtables: don't crash when using dnat target in output chains

[ Upstream commit b23c0742c2ce7e33ed79d10e451f70fdb5ca85d1 ]

xt_in() returns NULL in the output hook, skip the pkt_type change for
that case, redirection only makes sense in broute/prerouting hooks.

Reported-by: Tom Yan <tom.ty89@gmail.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: cf3cb246e277d ("bridge: ebtables: fix reception of frames DNAT-ed to bridge device/port")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: fec: add missed clk_disable_unprepare in remove

[ Upstream commit c43eab3eddb4c6742ac20138659a9b701822b274 ]

This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: ti: dra7-atl-clock: Remove ti_clk_add_alias call

[ Upstream commit 9982b0f69b49931b652d35f86f519be2ccfc7027 ]

ti_clk_register() calls it already so the driver should not create
duplicated alias.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lkml.kernel.org/r/20191002083436.10194-1-peter.ujfalusi@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/resctrl: Prevent NULL pointer dereference when reading mondata

[ Upstream commit 26467b0f8407cbd628fa5b7bcfd156e772004155 ]

When a mon group is being deleted, rdtgrp->flags is set to RDT_DELETED
in rdtgroup_rmdir_mon() firstly. The structure of rdtgrp will be freed
until rdtgrp->waitcount is dropped to 0 in rdtgroup_kn_unlock() later.

During the window of deleting a mon group, if an application calls
rdtgroup_mondata_show() to read mondata under this mon group,
'rdtgrp' returned from rdtgroup_kn_lock_live() is a NULL pointer when
rdtgrp->flags is RDT_DELETED. And then 'rdtgrp' is passed in this path:
rdtgroup_mondata_show() --> mon_event_read() --> mon_event_count().
Thus it results in NULL pointer dereference in mon_event_count().

Check 'rdtgrp' in rdtgroup_mondata_show(), and return -ENOENT
immediately when reading mondata during the window of deleting a mon
group.

Fixes: d89b7379015f ("x86/intel_rdt/cqm: Add mon_data")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: pei.p.jia@intel.com
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1572326702-27577-1-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

idr: Fix idr_alloc_u32 on 32-bit systems

[ Upstream commit b7e9728f3d7fc5c5c8508d99f1675212af5cfd49 ]

Attempting to allocate an entry at 0xffffffff when one is already
present would succeed in allocating one at 2^32, which would confuse
everything.  Return -ENOSPC in this case, as expected.

Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: sunxi-ng: a80: fix the zero'ing of bits 16 and 18

[ Upstream commit cdfc2e2086bf9c465f44e2db25561373b084a113 ]

The zero'ing of bits 16 and 18 is incorrect. Currently the code
is masking with the bitwise-and of BIT(16) & BIT(18) which is
0, so the updated value for val is always zero. Fix this by bitwise
and-ing value with the correct mask that will zero bits 16 and 18.

Addresses-Coverity: (" Suspicious &= or |= constant expression")
Fixes: b8eb71dcdd08 ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: at91: avoid sleeping early

[ Upstream commit 658fd65cf0b0d511de1718e48d9a28844c385ae0 ]

It is not allowed to sleep to early in the boot process and this may lead
to kernel issues if the bootloader didn't prepare the slow clock and main
clock.

This results in the following error and dump stack on the AriettaG25:
   bad: scheduling from the idle thread!

Ensure it is possible to sleep, else simply have a delay.

Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lkml.kernel.org/r/20190920153906.20887-1-alexandre.belloni@bootlin.com
Fixes: 80eded6ce8bb ("clk: at91: add slow clks driver")
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

reset: fix reset_control_ops kerneldoc comment

[ Upstream commit f430c7ed8bc22992ed528b518da465b060b9223f ]

Add a missing short description to the reset_control_ops documentation.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[p.zabel@pengutronix.de: rebased and updated commit message]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume

[ Upstream commit e9323b664ce29547d996195e8a6129a351c39108 ]

Properly save and restore all top PLL related configuration registers
during suspend/resume cycle. So far driver only handled EPLL and RPLL
clocks, all other were reset to default values after suspend/resume cycle.
This caused for example lower G3D (MALI Panfrost) performance after system
resume, even if performance governor has been selected.

Reported-by: Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Fixes: 773424326b51 ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: kirkwood: fix external clock probe defer

[ Upstream commit 4523817d51bc3b2ef38da768d004fda2c8bc41de ]

When our call to get the external clock fails, we forget to clean up
the enabled internal clock correctly.  Enable the clock after we have
obtained all our resources.

Fixes: 84aac6c79bfd ("ASoC: kirkwood: fix loss of external clock at probe time")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iNGyK-0004oF-6A@rmk-PC.armlinux.org.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

reset: Fix memory leak in reset_control_array_put()

[ Upstream commit 532f9cd6ee994ed10403e856ca27501428048597 ]

Memory allocated for 'struct reset_control_array' in
of_reset_control_array_get() is never freed in
reset_control_array_put() resulting in kmemleak showing
the following backtrace.

  backtrace:
    [<00000000c5f17595>] __kmalloc+0x1b0/0x2b0
    [<00000000bd499e13>] of_reset_control_array_get+0xa4/0x180
    [<000000004cc02754>] 0xffff800008c669e4
    [<0000000050a83b24>] platform_drv_probe+0x50/0xa0
    [<00000000d3a0b0bc>] really_probe+0x108/0x348
    [<000000005aa458ac>] driver_probe_device+0x58/0x100
    [<000000008853626c>] device_driver_attach+0x6c/0x90
    [<0000000085308d19>] __driver_attach+0x84/0xc8
    [<00000000080d35f2>] bus_for_each_dev+0x74/0xc8
    [<00000000dd7f015b>] driver_attach+0x20/0x28
    [<00000000923ba6e6>] bus_add_driver+0x148/0x1f0
    [<0000000061473b66>] driver_register+0x60/0x110
    [<00000000c5bec167>] __platform_driver_register+0x40/0x48
    [<000000007c764b4f>] 0xffff800008c6c020
    [<0000000047ec2e8c>] do_one_initcall+0x5c/0x1b0
    [<0000000093d4b50d>] do_init_module+0x54/0x1d0

Fixes: 17c82e206d2a ("reset: Add APIs to manage array of resets")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: compress: fix unsigned integer overflow check

[ Upstream commit d3645b055399538415586ebaacaedebc1e5899b0 ]

Parameter fragments and fragment_size are type of u32. U32_MAX is
the correct check.

Signed-off-by: Xiaojun Sang <xsang@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191021095432.5639-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: msm8916-wcd-analog: Fix RX1 selection in RDAC2 MUX

[ Upstream commit 9110d1b0e229cebb1ffce0c04db2b22beffd513d ]

According to the PM8916 Hardware Register Description,
CDC_D_CDC_CONN_HPHR_DAC_CTL has only a single bit (RX_SEL)
to switch between RX1 (0) and RX2 (1). It is not possible to
disable it entirely to achieve the "ZERO" state.

However, at the moment the "RDAC2 MUX" mixer defines three possible
values ("ZERO", "RX2" and "RX1"). Setting the mixer to "ZERO"
actually configures it to RX1. Setting the mixer to "RX1" has
(seemingly) no effect.

Remove "ZERO" and replace it with "RX1" to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191020153007.206070-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: meson: gxbb: let sar_adc_clk_div set the parent clock rate

[ Upstream commit 44b09b11b813b8550e6b976ea51593bc23bba8d1 ]

The meson-saradc driver manually sets the input clock for
sar_adc_clk_sel. Update the GXBB clock driver (which is used on GXBB,
GXL and GXM) so the rate settings on sar_adc_clk_div are propagated up
to sar_adc_clk_sel which will let the common clock framework select the
best matching parent clock if we want that.

This makes sar_adc_clk_div consistent with the axg-aoclk and g12a-aoclk
drivers, which both also specify CLK_SET_RATE_PARENT.

Fixes: 33d0fcdfe0e870 ("clk: gxbb: add the SAR ADC clocks and expose them")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "KVM: nVMX: reset cache/shadows when switching loaded VMCS"

This reverts commit 9f0b41be6aff47c24c6431bdc76f86b9cd647a0d which is
commit b7031fd40fcc741b0f9b0c04c8d844e445858b84 upstream.

It should not have been selected for a stable kernel as it breaks the
nVMX regression tests.

Reported-by: Jack Wang <jack.wang.usish@gmail.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.157

x86/hyperv: mark hyperv_init as __init function

This change was done upstream as part of 6b48cb5f8347 ("X86/Hyper-V:
Enlighten APIC access"), but that commit introduced a lot of new
functionality we don't want to backport.

This change eliminates a build warning.

Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S HV: Flush link stack on guest exit to host kernel

commit af2e8c68b9c5403f77096969c516f742f5bb29e0 upstream.

On some systems that are vulnerable to Spectre v2, it is up to
software to flush the link stack (return address stack), in order to
protect against Spectre-RSB.

When exiting from a guest we do some house keeping and then
potentially exit to C code which is several stack frames deep in the
host kernel. We will then execute a series of returns without
preceeding calls, opening up the possiblity that the guest could have
poisoned the link stack, and direct speculative execution of the host
to a gadget of some sort.

To prevent this we add a flush of the link stack on exit from a guest.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[dja: straightforward backport to v4.14]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/book3s64: Fix link stack flush on context switch

commit 39e72bf96f5847ba87cc5bd7a3ce0fed813dc9ad upstream.

In commit ee13cb249fab ("powerpc/64s: Add support for software count
cache flush"), I added support for software to flush the count
cache (indirect branch cache) on context switch if firmware told us
that was the required mitigation for Spectre v2.

As part of that code we also added a software flush of the link
stack (return address stack), which protects against Spectre-RSB
between user processes.

That is all correct for CPUs that activate that mitigation, which is
currently Power9 Nimbus DD2.3.

What I got wrong is that on older CPUs, where firmware has disabled
the count cache, we also need to flush the link stack on context
switch.

To fix it we create a new feature bit which is not set by firmware,
which tells us we need to flush the link stack. We set that when
firmware tells us that either of the existing Spectre v2 mitigations
are enabled.

Then we adjust the patching code so that if we see that feature bit we
enable the link stack flush. If we're also told to flush the count
cache in software then we fall through and do that also.

On the older CPUs we don't need to do do the software count cache
flush, firmware has disabled it, so in that case we patch in an early
return after the link stack flush.

The naming of some of the functions is awkward after this patch,
because they're called "count cache" but they also do link stack. But
we'll fix that up in a later commit to ease backporting.

This is the fix for CVE-2019-18660.

Reported-by: Anthony Steinhauser <asteinhauser@google.com>
Fixes: ee13cb249fab ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[dja: straightforward backport to v4.14]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: support nospectre_v2 cmdline option

commit d8f0e0b073e1ec52a05f0c2a56318b47387d2f10 upstream.

Add support for disabling the kernel implemented spectre v2 mitigation
(count cache flush on context switch) via the nospectre_v2 and
mitigations=off cmdline options.

Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christopher M. Riedl <cmr@informatik.wtf>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190524024647.381-1-cmr@informatik.wtf
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error

commit 5618332e5b955b4bff06d0b88146b971c8dd7b32 upstream.

The userspace comedilib function 'get_cmd_generic_timed' fills
the cmd structure with an informed guess and then calls the
function 'usbduxfast_ai_cmdtest' in this driver repeatedly while
'usbduxfast_ai_cmdtest' is modifying the cmd struct until it
no longer changes. However, because of rounding errors this never
converged because 'steps = (cmd->convert_arg * 30) / 1000' and then
back to 'cmd->convert_arg = (steps * 1000) / 30' won't be the same
because of rounding errors. 'Steps' should only be converted back to
the 'convert_arg' if 'steps' has actually been modified. In addition
the case of steps being 0 wasn't checked which is also now done.

Signed-off-by: Bernd Porr <mail@berndporr.me.uk>
Cc: <stable@vger.kernel.org> # 4.4+
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20191118230759.1727-1-mail@berndporr.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add support for Foxconn T77W968 LTE modules

commit f0797095423e6ea3b4be61134ee353c7f504d440 upstream.

These are the Foxconn-branded variants of the Dell DW5821e modules,
same USB layout as those. The device exposes AT, NMEA and DIAG ports
in both USB configurations.

P:  Vendor=0489 ProdID=e0b4 Rev=03.18
S:  Manufacturer=FII
S:  Product=T77W968 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

P:  Vendor=0489 ProdID=e0b4 Rev=03.18
S:  Manufacturer=FII
S:  Product=T77W968 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#=0x6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
[ johan: drop id defines ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add support for DW5821e with eSIM support

commit 957c31ea082e3fe5196f46d5b04018b10de47400 upstream.

The device exposes AT, NMEA and DIAG ports in both USB configurations.
Exactly same layout as the default DW5821e module, just a different
vid/pid.

P:  Vendor=413c ProdID=81e0 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5821e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

P:  Vendor=413c ProdID=81e0 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5821e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#=0x6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: mos7840: fix remote wakeup

commit 92fe35fb9c70a00d8fbbf5bd6172c921dd9c7815 upstream.

The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.

Note that USB core would clear the remote-wakeup feature at first
resume.

Fixes: 3f5429746d91 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: mos7720: fix remote wakeup

commit ea422312a462696093b5db59d294439796cba4ad upstream.

The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.

Note that USB core would clear the remote-wakeup feature at first
resume.

Fixes: 0f64478cbc7a ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: mos7840: add USB ID to support Moxa UPort 2210

commit e696d00e65e81d46e911f24b12e441037bf11b38 upstream.

Add USB ID for MOXA UPort 2210. This device contains mos7820 but
it passes GPIO0 check implemented by driver and it's detected as
mos7840. Hence product id check is added to force mos7820 mode.

Signed-off-by: Pavel Löbl <pavel@loebl.cz>
Cc: stable <stable@vger.kernel.org>
[ johan: rename id defines and add vendor-id check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

appledisplay: fix error handling in the scheduled work

commit 91feb01596e5efc0cc922cc73f5583114dccf4d2 upstream.

The work item can operate on

1. stale memory left over from the last transfer
the actual length of the data transfered needs to be checked
2. memory already freed
the error handling in appledisplay_probe() needs
to cancel the work in that case

Reported-and-tested-by: syzbot+495dab1f175edc9c2f13@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106124902.7765-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: chaoskey: fix error case of a timeout

commit 92aa5986f4f7b5a8bf282ca0f50967f4326559f5 upstream.

In case of a timeout or if a signal aborts a read
communication with the device needs to be ended
lest we overwrite an active URB the next time we
do IO to the device, as the URB may still be active.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191107142856.16774-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-serial: cp201x: support Mark-10 digital force gauge

commit 347bc8cb26388791c5881a3775cb14a3f765a674 upstream.

Add support for the Mark-10 digital force gauge device to the cp201x
driver.

Based on a report and a larger patch from Joel Jennings

Reported-by: Joel Jennings <joel.jennings@makeitlabs.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191118092119.GA153852@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: Fix uninitialized symbol 'nents' in stub_recv_cmd_submit()

commit 2a9125317b247f2cf35c196f968906dcf062ae2d upstream.

Smatch reported that nents is not initialized and used in
stub_recv_cmd_submit(). nents is currently initialized by sgl_alloc()
and used to allocate multiple URBs when host controller doesn't
support scatter-gather DMA. The use of uninitialized nents means that
buf_len is zero and use_sg is true. But buffer length should not be
zero when an URB uses scatter-gather DMA.

To prevent this situation, add the conditional that checks buf_len
and use_sg. And move the use of nents right after the sgl_alloc() to
avoid the use of uninitialized nents.

If the error occurs, it adds SDEV_EVENT_ERROR_MALLOC and stub_priv
will be released by stub event handler and connection will be shut
down.

Fixes: ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191111141035.27788-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: tools: fix fd leakage in the function of read_attr_usbip_status

commit 26a4d4c00f85cb844dd11dd35e848b079c2f5e8f upstream.

We should close the fd before the return of read_attr_usbip_status.

Fixes: 3391ba0e2792 ("usbip: tools: Extract generic code to be shared with vudc backend")
Signed-off-by: Hewenliang <hewenliang4@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191025043515.20053-1-hewenliang4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_ring: fix return code on DMA mapping fails

[ Upstream commit f7728002c1c7bfa787b276a31c3ef458739b8e7c ]

Commit 780bc7903a32 ("virtio_ring: Support DMA APIs")  makes
virtqueue_add() return -EIO when we fail to map our I/O buffers. This is
a very realistic scenario for guests with encrypted memory, as swiotlb
may run out of space, depending on it's size and the I/O load.

The virtio-blk driver interprets -EIO form virtqueue_add() as an IO
error, despite the fact that swiotlb full is in absence of bugs a
recoverable condition.

Let us change the return code to -ENOMEM, and make the block layer
recover form these failures when virtio-blk encounters the condition
described above.

Cc: stable@vger.kernel.org
Fixes: 780bc7903a32 ("virtio_ring: Support DMA APIs")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Michael Mueller <mimu@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: imon: invalid dereference in imon_touch_event

commit f3f5ba42c58d56d50f539854d8cc188944e96087 upstream.

The touch timer is set up in intf1. If the second interface does not exist,
the timer and touch input device are not setup and we get the following
error, when touch events are reported via intf0.

kernel BUG at kernel/time/timer.c:956!
invalid opcode: 0000 [#1] SMP KASAN
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc1+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__mod_timer kernel/time/timer.c:956 [inline]
RIP: 0010:__mod_timer kernel/time/timer.c:949 [inline]
RIP: 0010:mod_timer+0x5a2/0xb50 kernel/time/timer.c:1100
Code: 45 10 c7 44 24 14 ff ff ff ff 48 89 44 24 08 48 8d 45 20 48 c7 44 24 18 00 00 00 00 48 89 04 24 e9 5a fc ff ff e8 ae ce 0e 00 <0f> 0b e8 a7 ce 0e 00 4c 89 74 24 20 e9 37 fe ff ff e8 98 ce 0e 00
RSP: 0018:ffff8881db209930 EFLAGS: 00010006
RAX: ffffffff86c2b200 RBX: 00000000ffffa688 RCX: ffffffff83efc583
RDX: 0000000000000100 RSI: ffffffff812f4d82 RDI: ffff8881d2356200
RBP: ffff8881d23561e8 R08: ffffffff86c2b200 R09: ffffed103a46abeb
R10: ffffed103a46abea R11: ffff8881d2355f53 R12: dffffc0000000000
R13: 1ffff1103b64132d R14: ffff8881d2355f50 R15: 0000000000000006
FS:  0000000000000000(0000) GS:ffff8881db200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f75e2799000 CR3: 00000001d3b07000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <IRQ>
 imon_touch_event drivers/media/rc/imon.c:1348 [inline]
 imon_incoming_packet.isra.0+0x2546/0x2f10 drivers/media/rc/imon.c:1603
 usb_rx_callback_intf0+0x151/0x1e0 drivers/media/rc/imon.c:1734
 __usb_hcd_giveback_urb+0x1f2/0x470 drivers/usb/core/hcd.c:1654
 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1719
 dummy_timer+0x120f/0x2fa2 drivers/usb/gadget/udc/dummy_hcd.c:1965
 call_timer_fn+0x179/0x650 kernel/time/timer.c:1404
 expire_timers kernel/time/timer.c:1449 [inline]
 __run_timers kernel/time/timer.c:1773 [inline]
 __run_timers kernel/time/timer.c:1740 [inline]
 run_timer_softirq+0x5e3/0x1490 kernel/time/timer.c:1786
 __do_softirq+0x221/0x912 kernel/softirq.c:292
 invoke_softirq kernel/softirq.c:373 [inline]
 irq_exit+0x178/0x1a0 kernel/softirq.c:413
 exiting_irq arch/x86/include/asm/apic.h:536 [inline]
 smp_apic_timer_interrupt+0x12f/0x500 arch/x86/kernel/apic/apic.c:1137
 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:830
 </IRQ>
RIP: 0010:default_idle+0x28/0x2e0 arch/x86/kernel/process.c:581
Code: 90 90 41 56 41 55 65 44 8b 2d 44 3a 8f 7a 41 54 55 53 0f 1f 44 00 00 e8 36 ee d0 fb e9 07 00 00 00 0f 00 2d fa dd 4f 00 fb f4 <65> 44 8b 2d 20 3a 8f 7a 0f 1f 44 00 00 5b 5d 41 5c 41 5d 41 5e c3
RSP: 0018:ffffffff86c07da8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13
RAX: 0000000000000007 RBX: ffffffff86c2b200 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000006 RDI: ffffffff86c2ba4c
RBP: fffffbfff0d85640 R08: ffffffff86c2b200 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
 cpuidle_idle_call kernel/sched/idle.c:154 [inline]
 do_idle+0x3b6/0x500 kernel/sched/idle.c:263
 cpu_startup_entry+0x14/0x20 kernel/sched/idle.c:355
 start_kernel+0x82a/0x864 init/main.c:784
 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241
Modules linked in:

Reported-by: syzbot+f49d12d34f2321cf4df2@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: cxusb: detect cxusb_ctrl_msg error in query

commit ca8f245f284eeffa56f3b7a5eb6fc503159ee028 upstream.

Don't use uninitialized ircode[] in cxusb_rc_query() when
cxusb_ctrl_msg() fails to populate its contents.

syzbot reported:

dvb-usb: bulk message failed: -22 (1/-30591)
=====================================================
BUG: KMSAN: uninit-value in ir_lookup_by_scancode drivers/media/rc/rc-main.c:494 [inline]
BUG: KMSAN: uninit-value in rc_g_keycode_from_table drivers/media/rc/rc-main.c:582 [inline]
BUG: KMSAN: uninit-value in rc_keydown+0x1a6/0x6f0 drivers/media/rc/rc-main.c:816
CPU: 1 PID: 11436 Comm: kworker/1:2 Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events dvb_usb_read_remote_control
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x191/0x1f0 lib/dump_stack.c:113
 kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
 __msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
 bsearch+0x1dd/0x250 lib/bsearch.c:41
 ir_lookup_by_scancode drivers/media/rc/rc-main.c:494 [inline]
 rc_g_keycode_from_table drivers/media/rc/rc-main.c:582 [inline]
 rc_keydown+0x1a6/0x6f0 drivers/media/rc/rc-main.c:816
 cxusb_rc_query+0x2e1/0x360 drivers/media/usb/dvb-usb/cxusb.c:548
 dvb_usb_read_remote_control+0xf9/0x290 drivers/media/usb/dvb-usb/dvb-usb-remote.c:261
 process_one_work+0x1572/0x1ef0 kernel/workqueue.c:2269
 worker_thread+0x111b/0x2460 kernel/workqueue.c:2415
 kthread+0x4b5/0x4f0 kernel/kthread.c:256
 ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:355

Uninit was stored to memory at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:150 [inline]
 kmsan_internal_chain_origin+0xd2/0x170 mm/kmsan/kmsan.c:314
 __msan_chain_origin+0x6b/0xe0 mm/kmsan/kmsan_instr.c:184
 rc_g_keycode_from_table drivers/media/rc/rc-main.c:583 [inline]
 rc_keydown+0x2c4/0x6f0 drivers/media/rc/rc-main.c:816
 cxusb_rc_query+0x2e1/0x360 drivers/media/usb/dvb-usb/cxusb.c:548
 dvb_usb_read_remote_control+0xf9/0x290 drivers/media/usb/dvb-usb/dvb-usb-remote.c:261
 process_one_work+0x1572/0x1ef0 kernel/workqueue.c:2269
 worker_thread+0x111b/0x2460 kernel/workqueue.c:2415
 kthread+0x4b5/0x4f0 kernel/kthread.c:256
 ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:355

Local variable description: ----ircode@cxusb_rc_query
Variable was created at:
 cxusb_rc_query+0x4d/0x360 drivers/media/usb/dvb-usb/cxusb.c:543
 dvb_usb_read_remote_control+0xf9/0x290 drivers/media/usb/dvb-usb/dvb-usb-remote.c:261

Signed-off-by: Vito Caputo <vcaputo@pengaru.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: b2c2-flexcop-usb: add sanity checking

commit 1b976fc6d684e3282914cdbe7a8d68fdce19095c upstream.

The driver needs an isochronous endpoint to be present. It will
oops in its absence. Add checking for it.

Reported-by: syzbot+d93dff37e6a89431c158@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: uvcvideo: Fix error path in control parsing failure

commit 8c279e9394cade640ed86ec6c6645a0e7df5e0b6 upstream.

When parsing the UVC control descriptors fails, the error path tries to
cleanup a media device that hasn't been initialised, potentially
resulting in a crash. Fix this by initialising the media device before
the error handling path can be reached.

Fixes: 5a254d751e52 ("[media] uvcvideo: Register a v4l2_device")
Reported-by: syzbot+c86454eb3af9e8a4da20@syzkaller.appspotmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: Add NULL checks to show() and store() methods of cpufreq

commit e6e8df07268c1f75dd9215536e2ce4587b70f977 upstream.

Add NULL checks to show() and store() in cpufreq.c to avoid attempts
to invoke a NULL callback.

Though some interfaces of cpufreq are set as read-only, users can
still get write permission using chmod which can lead to a kernel
crash, as follows:

chmod +w /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
echo 1 >  /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq

This bug was found in linux 4.19.

Signed-off-by: Kai Shen <shenkai8@huawei.com>
Reported-by: Feilong Lin <linfeilong@huawei.com>
Reviewed-by: Feilong Lin <linfeilong@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: usbvision: Fix races among open, close, and disconnect

commit 9e08117c9d4efc1e1bc6fce83dab856d9fd284b6 upstream.

Visual inspection of the usbvision driver shows that it suffers from
three races between its open, close, and disconnect handlers.  In
particular, the driver is careful to update its usbvision->user and
usbvision->remove_pending flags while holding the private mutex, but:

usbvision_v4l2_close() and usbvision_radio_close() don't hold
the mutex while they check the value of
usbvision->remove_pending;

usbvision_disconnect() doesn't hold the mutex while checking
the value of usbvision->user; and

also, usbvision_v4l2_open() and usbvision_radio_open() don't
check whether the device has been unplugged before allowing
the user to open the device files.

Each of these can potentially lead to usbvision_release() being called
twice and use-after-free errors.

This patch fixes the races by reading the flags while the mutex is
still held and checking for pending removes before allowing an open to
succeed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: vivid: Fix wrong locking that causes race conditions on streaming stop

commit 6dcd5d7a7a29c1e4b8016a06aed78cd650cd8c27 upstream.

There is the same incorrect approach to locking implemented in
vivid_stop_generating_vid_cap(), vivid_stop_generating_vid_out() and
sdr_cap_stop_streaming().

These functions are called during streaming stopping with vivid_dev.mutex
locked. And they all do the same mistake while stopping their kthreads,
which need to lock this mutex as well. See the example from
vivid_stop_generating_vid_cap():
  /* shutdown control thread */
  vivid_grab_controls(dev, false);
  mutex_unlock(&dev->mutex);
  kthread_stop(dev->kthread_vid_cap);
  dev->kthread_vid_cap = NULL;
  mutex_lock(&dev->mutex);

But when this mutex is unlocked, another vb2_fop_read() can lock it
instead of vivid_thread_vid_cap() and manipulate the buffer queue.
That causes a use-after-free access later.

To fix those issues let's:
  1. avoid unlocking the mutex in vivid_stop_generating_vid_cap(),
vivid_stop_generating_vid_out() and sdr_cap_stop_streaming();
  2. use mutex_trylock() with schedule_timeout_uninterruptible() in
the loops of the vivid kthread handlers.

Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: vivid: Set vid_cap_streaming and vid_out_streaming to true

commit b4add02d2236fd5f568db141cfd8eb4290972eb3 upstream.

When vbi stream is started, followed by video streaming,
the vid_cap_streaming and vid_out_streaming were not being set to true,
which would cause the video stream to stop when vbi stream is stopped.
This patch allows to set vid_cap_streaming and vid_out_streaming to true.
According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)'
checks are a left-over from the original vivid development and should never
have been there.

Signed-off-by: Vandana BN <bnvandana@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfc: port100: handle command failure cleanly

commit 5f9f0b11f0816b35867f2cf71e54d95f53f03902 upstream.

If starting the transfer of a command suceeds but the transfer for the reply
fails, it is not enough to initiate killing the transfer for the
command may still be running. You need to wait for the killing to finish
before you can reuse URB and buffer.

Reported-and-tested-by: syzbot+711468aa5c3a1eabf863@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nbd: prevent memory leak

commit 03bf73c315edca28f47451913177e14cd040a216 upstream.

In nbd_add_socket when krealloc succeeds, if nsock's allocation fail the
reallocted memory is leak. The correct behaviour should be assigning the
reallocted memory to config->socks right after success.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/speculation: Fix redundant MDS mitigation message

commit cd5a2aa89e847bdda7b62029d94e95488d73f6b2 upstream.

Since MDS and TAA mitigations are inter-related for processors that are
affected by both vulnerabilities, the followiing confusing messages can
be printed in the kernel log:

  MDS: Vulnerable
  MDS: Mitigation: Clear CPU buffers

To avoid the first incorrect message, defer the printing of MDS
mitigation after the TAA mitigation selection has been done. However,
that has the side effect of printing TAA mitigation first before MDS
mitigation.

 [ bp: Check box is affected/mitigations are disabled first before
   printing and massage. ]

Suggested-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Mark Gross <mgross@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191115161445.30809-3-longman@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/speculation: Fix incorrect MDS/TAA mitigation status

commit 64870ed1b12e235cfca3f6c6da75b542c973ff78 upstream.

For MDS vulnerable processors with TSX support, enabling either MDS or
TAA mitigations will enable the use of VERW to flush internal processor
buffers at the right code path. IOW, they are either both mitigated
or both not. However, if the command line options are inconsistent,
the vulnerabilites sysfs files may not report the mitigation status
correctly.

For example, with only the "mds=off" option:

  vulnerabilities/mds:Vulnerable; SMT vulnerable
  vulnerabilities/tsx_async_abort:Mitigation: Clear CPU buffers; SMT vulnerable

The mds vulnerabilities file has wrong status in this case. Similarly,
the taa vulnerability file will be wrong with mds mitigation on, but
taa off.

Change taa_select_mitigation() to sync up the two mitigation status
and have them turned off if both "mds=off" and "tsx_async_abort=off"
are present.

Update documentation to emphasize the fact that both "mds=off" and
"tsx_async_abort=off" have to be specified together for processors that
are affected by both TAA and MDS to be effective.

 [ bp: Massage and add kernel-parameters.txt change too. ]

Fixes: 1b42f017415b ("x86/speculation/taa: Add mitigation for TSX Async Abort")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: linux-doc@vger.kernel.org
Cc: Mark Gross <mgross@linux.intel.com>
Cc: <stable@vger.kernel.org>
Cc: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191115161445.30809-2-longman@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/insn: Fix awk regexp warnings

commit 700c1018b86d0d4b3f1f2d459708c0cdf42b521d upstream.

gawk 5.0.1 generates the following regexp warnings:

  GEN      /home/sasha/torvalds/tools/objtool/arch/x86/lib/inat-tables.c
  awk: ../arch/x86/tools/gen-insn-attr-x86.awk:260: warning: regexp escape sequence `\:' is not a known regexp operator
  awk: ../arch/x86/tools/gen-insn-attr-x86.awk:350: (FILENAME=../arch/x86/lib/x86-opcode-map.txt FNR=41) warning: regexp escape sequence `\&' is  not a known regexp operator

Ealier versions of gawk are not known to generate these warnings. The
gawk manual referenced below does not list characters ':' and '&' as
needing escaping, so 'unescape' them. See

  https://www.gnu.org/software/gawk/manual/html_node/Escape-Sequences.html

for more info.

Running diff on the output generated by the script before and after
applying the patch reported no differences.

 [ bp: Massage commit message. ]

[ Caught the respective tools header discrepancy. ]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190924044659.3785-1-alexander.kapshuk@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: perf: Accommodate big-endian CPU

commit 5effc09c4907901f0e71e68e5f2e14211d9a203f upstream.

8-letter strings representing ARC perf events are stores in two
32-bit registers as ASCII characters like that: "IJMP", "IALL", "IJMPTAK" etc.

And the same order of bytes in the word is used regardless CPU endianness.

Which means in case of big-endian CPU core we need to swap bytes to get
the same order as if it was on little-endian CPU.

Otherwise we're seeing the following error message on boot:
------------------------->8----------------------
ARC perf        : 8 counters (32 bits), 40 conditions, [overflow IRQ support]
sysfs: cannot create duplicate filename '/devices/arc_pct/events/pmji'
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.18 #3
Stack Trace:
  arc_unwind_core+0xd4/0xfc
  dump_stack+0x64/0x80
  sysfs_warn_dup+0x46/0x58
  sysfs_add_file_mode_ns+0xb2/0x168
  create_files+0x70/0x2a0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/events/core.c:12144 perf_event_sysfs_init+0x70/0xa0
Failed to register pmu: arc_pct, reason -17
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.18 #3
Stack Trace:
  arc_unwind_core+0xd4/0xfc
  dump_stack+0x64/0x80
  __warn+0x9c/0xd4
  warn_slowpath_fmt+0x22/0x2c
  perf_event_sysfs_init+0x70/0xa0
---[ end trace a75fb9a9837bd1ec ]---
------------------------->8----------------------

What happens here we're trying to register more than one raw perf event
with the same name "PMJI". Why? Because ARC perf events are 4 to 8 letters
and encoded into two 32-bit words. In this particular case we deal with 2
events:
 * "IJMP____" which counts all jump & branch instructions
 * "IJMPC___" which counts only conditional jumps & branches

Those strings are split in two 32-bit words this way "IJMP" + "____" &
"IJMP" + "C___" correspondingly. Now if we read them swapped due to CPU core
being big-endian then we read "PMJI" + "____" & "PMJI" + "___C".

And since we interpret read array of ASCII letters as a null-terminated string
on big-endian CPU we end up with 2 events of the same name "PMJI".

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8904/1: skip nomap memblocks while finding the lowmem/highmem boundary

commit 1d31999cf04c21709f72ceb17e65b54a401330da upstream.

adjust_lowmem_bounds() checks every memblocks in order to find the boundary
between lowmem and highmem. However some memblocks could be marked as NOMAP
so they are not used by kernel, which should be skipped while calculating
the boundary.

Signed-off-by: Chester Lin <clin@suse.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2: remove ocfs2_is_o2cb_active()

commit a634644751c46238df58bbfe992e30c1668388db upstream.

Remove ocfs2_is_o2cb_active().  We have similar functions to identify
which cluster stack is being used via osb->osb_cluster_stack.

Secondly, the current implementation of ocfs2_is_o2cb_active() is not
totally safe.  Based on the design of stackglue, we need to get
ocfs2_stack_lock before using ocfs2_stack related data structures, and
that active_stack pointer can be NULL in the case of mount failure.

Link: http://lkml.kernel.org/r/1495441079-11708-1-git-send-email-ghe@suse.com
Signed-off-by: Gang He <ghe@suse.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Reviewed-by: Eric Ren <zren@suse.com>
Acked-by: Changwei Ge <ge.changwei@h3c.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: Skip cpufreq resume if it's not suspended

commit 703cbaa601ff3fb554d1246c336ba727cc083ea0 upstream.

cpufreq_resume can be called even without preceding cpufreq_suspend.
This can happen in following scenario:

    suspend_devices_and_enter
       --> dpm_suspend_start
          --> dpm_prepare
              --> device_prepare : this function errors out
          --> dpm_suspend: this is skipped due to dpm_prepare failure
                           this means cpufreq_suspend is skipped over
       --> goto Recover_platform, due to previous error
       --> goto Resume_devices
       --> dpm_resume_end
           --> dpm_resume
               --> cpufreq_resume

In case schedutil is used as frequency governor, cpufreq_resume will
eventually call sugov_start, which does following:

    memset(sg_cpu, 0, sizeof(*sg_cpu));
    ....

This effectively erases function pointer for frequency update, causing
crash later on. The function pointer would have been set correctly if
subsequent cpufreq_add_update_util_hook runs successfully, but that
function returns earlier because cpufreq_suspend was not called:

    if (WARN_ON(per_cpu(cpufreq_update_util_data, cpu)))
return;

The fix is to check cpufreq_suspended first, if it's false, that means
cpufreq_suspend was not called in the first place, so do not resume
cpufreq.

Signed-off-by: Bo Yan <byan@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Dropped printing a message ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: fix for bad_mode() handler to always result in panic

commit e4ba15debcfd27f60d43da940a58108783bff2a6 upstream.

The bad_mode() handler is called if we encounter an uunknown exception,
with the expectation that the subsequent call to panic() will halt the
system. Unfortunately, if the exception calling bad_mode() is taken from
EL0, then the call to die() can end up killing the current user task and
calling schedule() instead of falling through to panic().

Remove the die() call altogether, since we really want to bring down the
machine in this "impossible" case.

Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: dp83867: increase SGMII autoneg timer duration

commit 1a97a477e666cbdededab93bd3754e508f0c09d7 upstream.

After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.

Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ adapted for kernels without phy_modify_mmd ]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: dp83867: fix speed 10 in sgmii mode

commit 333061b924539c0de081339643f45514f5f1c1e6 upstream.

For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.

Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ adapted for kernels without phy_modify_mmd ]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/memory_hotplug: don't access uninitialized memmaps in shrink_zone_span()

commit 7ce700bf11b5e2cb84e4352bbdf2123a7a239c84 upstream.

Let's limit shrinking to !ZONE_DEVICE so we can fix the current code.
We should never try to touch the memmap of offline sections where we
could have uninitialized memmaps and could trigger BUGs when calling
page_to_nid() on poisoned pages.

There is no reliable way to distinguish an uninitialized memmap from an
initialized memmap that belongs to ZONE_DEVICE, as we don't have
anything like SECTION_IS_ONLINE we can use similar to
pfn_to_online_section() for !ZONE_DEVICE memory.

E.g., set_zone_contiguous() similarly relies on pfn_to_online_section()
and will therefore never set a ZONE_DEVICE zone consecutive.  Stopping
to shrink the ZONE_DEVICE therefore results in no observable changes,
besides /proc/zoneinfo indicating different boundaries - something we
can totally live with.

Before commit d0dc12e86b31 ("mm/memory_hotplug: optimize memory
hotplug"), the memmap was initialized with 0 and the node with the right
value.  So the zone might be wrong but not garbage.  After that commit,
both the zone and the node will be garbage when touching uninitialized
memmaps.

Toshiki reported a BUG (race between delayed initialization of
ZONE_DEVICE memmaps without holding the memory hotplug lock and
concurrent zone shrinking).

  https://lkml.org/lkml/2019/11/14/1040

"Iteration of create and destroy namespace causes the panic as below:

      kernel BUG at mm/page_alloc.c:535!
      CPU: 7 PID: 2766 Comm: ndctl Not tainted 5.4.0-rc4 #6
      Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
      RIP: 0010:set_pfnblock_flags_mask+0x95/0xf0
      Call Trace:
       memmap_init_zone_device+0x165/0x17c
       memremap_pages+0x4c1/0x540
       devm_memremap_pages+0x1d/0x60
       pmem_attach_disk+0x16b/0x600 [nd_pmem]
       nvdimm_bus_probe+0x69/0x1c0
       really_probe+0x1c2/0x3e0
       driver_probe_device+0xb4/0x100
       device_driver_attach+0x4f/0x60
       bind_store+0xc9/0x110
       kernfs_fop_write+0x116/0x190
       vfs_write+0xa5/0x1a0
       ksys_write+0x59/0xd0
       do_syscall_64+0x5b/0x180
       entry_SYSCALL_64_after_hwframe+0x44/0xa9

  While creating a namespace and initializing memmap, if you destroy the
  namespace and shrink the zone, it will initialize the memmap outside
  the zone and trigger VM_BUG_ON_PAGE(!zone_spans_pfn(page_zone(page),
  pfn), page) in set_pfnblock_flags_mask()."

This BUG is also mitigated by this commit, where we for now stop to
shrink the ZONE_DEVICE zone until we can do it in a safe and clean way.

Link: http://lkml.kernel.org/r/20191006085646.5768-5-david@redhat.com
Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b319]
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reported-by: Toshiki Fukasawa <t-fukasawa@vx.jp.nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Damian Tometzki <damian.tometzki@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jun Yao <yaojun8558363@gmail.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Pankaj Gupta <pagupta@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Rich Felker <dalias@libc.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Yu Zhao <yuzhao@google.com>
Cc: <stable@vger.kernel.org> [4.13+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid10: prevent access of uninitialized resync_pages offset

commit 45422b704db392a6d79d07ee3e3670b11048bd53 upstream.

Due to unneeded multiplication in the out_free_pages portion of
r10buf_pool_alloc(), when using a 3-copy raid10 layout, it is
possible to access a resync_pages offset that has not been
initialized.  This access translates into a crash of the system
within resync_free_pages() while passing a bad pointer to
put_page().  Remove the multiplication, preventing access to the
uninitialized area.

Fixes: f0250618361db ("md: raid10: don't use bio's vec table to manage resync pages")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: John Pittman <jpittman@redhat.com>
Suggested-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k_hw: fix uninitialized variable data

commit 80e84f36412e0c5172447b6947068dca0d04ee82 upstream.

Currently, data variable in ar9003_hw_thermo_cal_apply() could be
uninitialized if ar9300_otp_read_word() will fail to read the value.
Initialize data variable with 0 to prevent an undefined behavior. This
will be enough to handle error case when ar9300_otp_read_word() fails.

Fixes: 80fe43f2bbd5 ("ath9k_hw: Read and configure thermocal for AR9462")
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: Fix a NULL-ptr-deref bug in ath10k_usb_alloc_urb_from_pipe

commit bfd6e6e6c5d2ee43a3d9902b36e01fc7527ebb27 upstream.

The `ar_usb` field of `ath10k_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath10k_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath10k_usb_setup_pipe_resources`:

for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
        endpoint = &iface_desc->endpoint[i].desc;

        // get the address from endpoint descriptor
        pipe_num = ath10k_usb_get_logical_pipe_num(ar_usb,
                                                endpoint->bEndpointAddress,
                                                &urbcount);
        ......
        // select the pipe object
        pipe = &ar_usb->pipes[pipe_num];

        // initialize the ar_usb field
        pipe->ar_usb = ar_usb;
}

The driver assumes that the addresses reported in endpoint
descriptors from device side  to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath10k_usb_alloc_urb_from_pipe` and
`ath10k_usb_free_urb_to_pipe`.

This patch fixes the bug by preventing potential NULL-ptr-deref.

Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[groeck: Add driver tag to subject, fix build warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: MMU: Do not treat ZONE_DEVICE pages as being reserved

commit a78986aae9b2988f8493f9f65a587ee433e83bc3 upstream.

Explicitly exempt ZONE_DEVICE pages from kvm_is_reserved_pfn() and
instead manually handle ZONE_DEVICE on a case-by-case basis.  For things
like page refcounts, KVM needs to treat ZONE_DEVICE pages like normal
pages, e.g. put pages grabbed via gup().  But for flows such as setting
A/D bits or shifting refcounts for transparent huge pages, KVM needs to
to avoid processing ZONE_DEVICE pages as the flows in question lack the
underlying machinery for proper handling of ZONE_DEVICE pages.

This fixes a hang reported by Adam Borowski[*] in dev_pagemap_cleanup()
when running a KVM guest backed with /dev/dax memory, as KVM straight up
doesn't put any references to ZONE_DEVICE pages acquired by gup().

Note, Dan Williams proposed an alternative solution of doing put_page()
on ZONE_DEVICE pages immediately after gup() in order to simplify the
auditing needed to ensure is_zone_device_page() is called if and only if
the backing device is pinned (via gup()).  But that approach would break
kvm_vcpu_{un}map() as KVM requires the page to be pinned from map() 'til
unmap() when accessing guest memory, unlike KVM's secondary MMU, which
coordinates with mmu_notifier invalidations to avoid creating stale
page references, i.e. doesn't rely on pages being pinned.

[*] http://lkml.kernel.org/r/20190919115547.GA17963@angband.pl

Reported-by: Adam Borowski <kilobyte@angband.pl>
Analyzed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Fixes: 3565fce3a659 ("mm, x86: get_user_pages() for dax mappings")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sean: backport to 4.x; resolve conflict in mmu.c]
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Fix invalid-free in bcsp_close()

commit cf94da6f502d8caecabd56b194541c873c8a7a3c upstream.

Syzbot reported an invalid-free that I introduced fixing a memleak.

bcsp_recv() also frees bcsp->rx_skb but never nullifies its value.
Nullify bcsp->rx_skb every time it is freed.

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+a0d209a4676664613e76@syzkaller.appspotmail.com
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: call disconnect_wk when AP stops

[ Upstream commit e005bd7ddea06784c1eb91ac5bb6b171a94f3b05 ]

Since we now prevent regulatory restore during STA disconnect
if concurrent AP interfaces are active, we need to reschedule
this check when the AP state changes. This fixes never doing
a restore when an AP is the last interface to stop. Or to put
it another way: we need to re-check after anything we check
here changes.

Cc: stable@vger.kernel.org
Fixes: 113f3aaa81bd ("cfg80211: Prevent regulatory restore during STA disconnect in concurrent interfaces")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv6: Fix handling of LLA with VRF and sockets bound to VRF

[ Upstream commit c2027d1e17582903e368abf5d4838b22a98f2b7b ]

A recent commit allows sockets bound to a VRF to receive ipv6 link local
packets. However, it only works for UDP and worse TCP connection attempts
to the LLA with the only listener bound to the VRF just hang where as
before the client gets a reset and connection refused. Fix by adjusting
ir_iif for LL addresses and packets received through a device enslaved
to a VRF.

Fixes: 6f12fa775530 ("vrf: mark skb for multicast or link-local as enslaved to VRF")
Reported-by: Donald Sharp <sharpd@cumulusnetworks.com>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mm/memory_hotplug: Do not unlock when fails to take the device_hotplug_lock

[ Upstream commit d2ab99403ee00d8014e651728a4702ea1ae5e52c ]

When adding the memory by probing memory block in sysfs interface, there is an
obvious issue that we will unlock the device_hotplug_lock when fails to takes it.

That issue was introduced in Commit 8df1d0e4a265
("mm/memory_hotplug: make add_memory() take the device_hotplug_lock")

We should drop out in time when fails to take the device_hotplug_lock.

Fixes: 8df1d0e4a265 ("mm/memory_hotplug: make add_memory() take the device_hotplug_lock")
Reported-by: Yang yingliang <yangyingliang@huawei.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: uniphier-f: fix timeout error after reading 8 bytes

[ Upstream commit c2a653deaa81f5a750c0dfcbaf9f8e5195cbe4a5 ]

I was totally screwed up in commit eaba68785c2d ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.

It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba68785c2d.

Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.

This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.

I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.

I consulted a hardware engineer, and I got the following information:

UNIPHIER_FI2C_INT_RF
    asserted at the falling edge of SCL at the 8th bit.

UNIPHIER_FI2C_INT_RB
    asserted at the rising edge of SCL at the 9th (ACK) bit.

In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.

Fixes: eaba68785c2d ("i2c: uniphier-f: fix race condition when IRQ is cleared")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: omap2-mcspi: Fix DMA and FIFO event trigger size mismatch

[ Upstream commit baf8b9f8d260c55a86405f70a384c29cda888476 ]

Commit b682cffa3ac6 ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length")
broke SPI transfers where bits_per_word != 8. This is because of
mimsatch between McSPI FIFO level event trigger size (SPI word length) and
DMA request size(word length * maxburst). This leads to data
corruption, lockup and errors like:

spi1.0: EOW timed out

Fix this by setting DMA maxburst size to 1 so that
McSPI FIFO level event trigger size matches DMA request size.

Fixes: b682cffa3ac6 ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length")
Cc: stable@vger.kernel.org
Reported-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: keystone: Use quirk to limit MRRS for K2G

[ Upstream commit 148e340c0696369fadbbddc8f4bef801ed247d71 ]

PCI controller in K2G also has a limitation that memory read request
size (MRRS) must not exceed 256 bytes. Use the quirk to limit MRRS
(added for K2HK, K2L and K2E) for K2G as well.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: zynq: Use define directive for PIN_CONFIG_IO_STANDARD

[ Upstream commit cd8a145a066a1a3beb0ae615c7cb2ee4217418d7 ]

Clang warns when one enumerated type is implicitly converted to another:

drivers/pinctrl/pinctrl-zynq.c:985:18: warning: implicit conversion from
enumeration type 'enum zynq_pin_config_param' to different enumeration
type 'enum pin_config_param' [-Wenum-conversion]
        {"io-standard", PIN_CONFIG_IOSTANDARD, zynq_iostd_lvcmos18},
        ~               ^~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-zynq.c:990:16: warning: implicit conversion from
enumeration type 'enum zynq_pin_config_param' to different enumeration
type 'enum pin_config_param' [-Wenum-conversion]
        = { PCONFDUMP(PIN_CONFIG_IOSTANDARD, "IO-standard", NULL, true),
            ~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/pinctrl/pinconf-generic.h:163:11: note: expanded from
macro 'PCONFDUMP'
        .param = a, .display = b, .format = c, .has_arg = d     \
                 ^
2 warnings generated.

It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.

Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: lpc18xx: Use define directive for PIN_CONFIG_GPIO_PIN_INT

[ Upstream commit f24bfb39975c241374cadebbd037c17960cf1412 ]

Clang warns when one enumerated type is implicitly converted to another:

drivers/pinctrl/pinctrl-lpc18xx.c:643:29: warning: implicit conversion
from enumeration type 'enum lpc18xx_pin_config_param' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
        {"nxp,gpio-pin-interrupt", PIN_CONFIG_GPIO_PIN_INT, 0},
        ~                          ^~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-lpc18xx.c:648:12: warning: implicit conversion
from enumeration type 'enum lpc18xx_pin_config_param' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
        PCONFDUMP(PIN_CONFIG_GPIO_PIN_INT, "gpio pin int", NULL, true),
        ~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/pinctrl/pinconf-generic.h:163:11: note: expanded from
macro 'PCONFDUMP'
        .param = a, .display = b, .format = c, .has_arg = d     \
                 ^
2 warnings generated.

It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.

Link: https://github.com/ClangBuiltLinux/linux/issues/140
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: qcom: spmi-gpio: fix gpio-hog related boot issues

[ Upstream commit 149a96047237574b756d872007c006acd0cc6687 ]

When attempting to setup up a gpio hog, device probing would repeatedly
fail with -EPROBE_DEFERED errors. It was caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.

See Christian Lamparter's commit a86caa9ba5d7 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.

Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cfg80211: Prevent regulatory restore during STA disconnect in concurrent interfaces

[ Upstream commit 113f3aaa81bd56aba02659786ed65cbd9cb9a6fc ]

Currently when an AP and STA interfaces are active in the same or different
radios, regulatory settings are restored whenever the STA disconnects. This
restores all channel information including dfs states in all radios.
For example, if an AP interface is active in one radio and STA in another,
when radar is detected on the AP interface, the dfs state of the channel
will be changed to UNAVAILABLE. But when the STA interface disconnects,
this issues a regulatory disconnect hint which restores all regulatory
settings in all the radios attached and thereby losing the stored dfs
state on the other radio where the channel was marked as unavailable
earlier. Hence prevent such regulatory restore whenever another active
beaconing interface is present in the same or other radios.

Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of: unittest: allow base devicetree to have symbol metadata

[ Upstream commit 5babefb7f7ab1f23861336d511cc666fa45ede82 ]

The overlay metadata nodes in the FDT created from testcases.dts
are not handled properly.

The __fixups__ and __local_fixups__ node were added to the live
devicetree, but should not be.

Only the first property in the /__symbols__ node was added to the
live devicetree if the live devicetree already contained a
/__symbols node.  All of the node's properties must be added.

Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: bcmgenet: return correct value 'ret' from bcmgenet_power_down

[ Upstream commit 0db55093b56618088b9a1d445eb6e43b311bea33 ]

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/broadcom/genet/bcmgenet.c: In function 'bcmgenet_power_down':
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1136:6: warning:
 variable 'ret' set but not used [-Wunused-but-set-variable]

bcmgenet_power_down should return 'ret' instead of 0.

Fixes: ca8cf341903f ("net: bcmgenet: propagate errors from bcmgenet_power_down")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: Use %d for signed int print formatting instead of %u

[ Upstream commit f8ddf49b420112e28bdd23d7ad52d7991a0ccbe3 ]

Fix warnings found using static analysis with cppcheck, use %d printf
format specifier for signed ints rather than %u

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vrf: mark skb for multicast or link-local as enslaved to VRF

[ Upstream commit 6f12fa775530195a501fb090d092c637f32d0cc5 ]

The skb for packets that are multicast or to a link-local address are
not marked as being enslaved to a VRF, if they are received on a socket
bound to the VRF. This is needed for ND and it is preferable for the
kernel not to have to deal with the additional use-cases if ll or mcast
packets are handled as enslaved. However, this does not allow service
instances listening on unbound and bound to VRF sockets to distinguish
the VRF used, if packets are sent as multicast or to a link-local
address. The fix is for the VRF driver to also mark these skb as being
enslaved to the VRF.

Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dlm: don't leak kernel pointer to userspace

[ Upstream commit 9de30f3f7f4d31037cfbb7c787e1089c1944b3a7 ]

In copy_result_to_user(), we first create a struct dlm_lock_result, which
contains a struct dlm_lksb, the last member of which is a pointer to the
lvb. Unfortunately, we copy the entire struct dlm_lksb to the result
struct, which is then copied to userspace at the end of the function,
leaking the contents of sb_lvbptr, which is a valid kernel pointer in some
cases (indeed, later in the same function the data it points to is copied
to userspace).

It is an error to leak kernel pointers to userspace, as it undermines KASLR
protections (see e.g. 65eea8edc31 ("floppy: Do not copy a kernel pointer to
user memory in FDGETPRM ioctl") for another example of this).

Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dlm: fix invalid free

[ Upstream commit d968b4e240cfe39d39d80483bac8bca8716fd93c ]

dlm_config_nodes() does not allocate nodes on failure, so we should not
free() nodes when it fails.

Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Correct loss of fc4 type on remote port address change

[ Upstream commit d83ca3ea833d7a66d49225e4191c4e37cab8f079 ]

An address change for a remote port cause PRLI for the wrong protocol
to be sent.  The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.

Fix the copy logic for the address change.  Beefed up log messages in
this area as well.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: fcoe: Fix link down issue after 1000+ link bounces

[ Upstream commit 036cad1f1ac9ce03e2db94b8460f98eaf1e1ee4c ]

On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.

Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>