iwlwifi: reuse page for notification packets

For notification packets and SKBs that fail to rx correctly, add
them back into the rx_free list so that the pages can be reused
later. This avoids allocating new rx pages unnecessarily.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: remove unused parameters

parameters "len" is not used in both iwl_tx_queue_free() and
iwl_cmd_queue_free() functions

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: remove duplicate defines

RX_FREE_BUFFERS and RX_LOW_WATERMARK are currently defined in four places.
Based on how files are included we only need the definition in iwl-fh.h

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add channel switch support to 5000 series and up

Support "channel switch" request by issue "channel switch" host command
to uCode.

There is no separated "channel switch" indication from mac80211,
when detected "IEEE80211_CONF_CHANGE_CHANNEL" flag in iwl_mac_config(),
if the station is in "associated" state, then assume "channel switch
announcement" IE was received by mac80211.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: issue ct_kill host command based on device config

Using device configuration structure to decide how to configure
ct_kill host command.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: choose thermal throttle method based on device config

Using device configuration structure to decide the type of thermal
throttle method for the device.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: increase max tfd payload size

Increase the size of TFD_MAX_PAYLOAD_SIZE (the size of iwl_device_cmd)
to accommodate iwl6000_channel_switch_cmd data structure.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix use after free bug for paged rx

In the paged rx patch (4854fde2), I introduced a bug that could possibly
touch an already freed page. It is fixed by avoiding the access in this
patch. I've also added some comments so that other people touching the
code won't make the same mistake. In the future, if we cannot avoid
access the page after being handled to the upper layer, we can use
get_page/put_page to handle it. For now, it's just not necessary.

It also fixed a debug message print bug reported by Stanislaw Gruszka
<sgruszka@redhat.com>.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: specify the valid tx/rx chain in device config structure

Specify both Tx and Rx chain in device configuration structure instead
of hard code in set_hw_params() for 4965

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update bt co-exit configuration parameter

Adding parameter ranges for bt co-exist configuration command.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: separate led function from statistic notification

Detach led background task from statistic notification routine. if led
blinking is required; the blink rate is based on the traffic condition.
It do not relate to statistics notification. In addition to that, there is
not a requirement for statistics notification has to occur all the time.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: consolidate apm_init() functions

Consolidate most iwlXXXX_apm_init() functions into single iwl_apm_init().
Keep iwl3945_apm_init(), but leverage iwl_apm_init() for most functionality.
Update 4965 init sequence to follow most recent factory recommendations.

Add following members to struct iwl_cfg to guide the init sequence:
pll_cfg_val (replaces needs_pll_cfg), set_l0s, use_bsm

Move L0S enable/disable from nic_config() functions to iwl_apm_init().
This satisifies the "FIXME: put here L1A -L0S w/a" notice, and complies
with factory-recommended sequence.

Add debug info message in iwl_apm_init(), and symmetrical message
in iwl_apm_stop().

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix gain computation for 5000 series and up

In Rx gain balancing (chain noise) computation for 5000 series and up,
the delta gain calculation should use the average noise of default
chain, not "chain 0" which do not exist for all the devices.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add missing commands to syslog messages

Two commands missing from list of commands such that when debug is
enabled, these commands are shown as UNKNOWN.

Missing commands are TX_ANT_CONFIGURATION_CMD and
TEMPERATURE_NOTIFICATION.

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove some references to IW_MODE_abc

... in pursue to quaff the wide-spread references to WEXT constants.

When setting SNMP_MIB_OID_BSS_TYPE, wext.c can directly calculate the value
the firmware wants.

Reading of SNMP_MIB_OID_BSS_TYPE doesn't happen anywhere, so no need to
convert the firmware value into WEXT values anyway.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: sort and categorize entries in decl.h

This now makes decl.h only contain declarations for functions that don't
have their own *.h file.

No function change.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: move mic failure event to wext.c

... because for cfg80211 we'll need a completely different
implementation.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: move SIOCGIWAP calls to wext.c

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove "struct cmd_ds_gen"

It was only used as a source for S_DS_GEN, but the size of this struct
is equal to the size of "struct cmd_header".

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove handling for CMD_GET_TSF

... which just resided as an old-style command in cmd/cmdresp, but
was nowhere useed. If we ever need it, we can re-add it as a newstyle
command.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove handling for CMD_802_11_LED_GPIO_CTRL

... which just resided as an old-style command in cmd/cmdresp, but
was nowhere useed. If we ever need it, we can re-add it as a newstyle
command.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: move lbs_send_iwevcustom_event() to wext.c

... because it's purely a WEXT function.

No functional change.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: move association related commands into assoc.c

That's because the new cfg80211 implementation will provide cleaner
implementations.

No functional changes.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: get current channel out of priv->curbssparams

... as priv->curbssparams won't exist once libertas+cfg80211 lands.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: sort variables in struct lbs_private

Having the variables in logical groups allows us to easier
#ifdef stuff out.

No functional change.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: move scan/assoc related stuff

Another cfg80211-preparation patch: removes some code/definitions from
main.c and dev.h and put's it into assoc.c/.h, scan.c/.h.

No function change.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: change IW_ESSID_MAX_SIZE -> IEEE80211_MAX_SSID_LEN

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove unused 11d.h as well, priv->countryinfo

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove unused 11d code

Most of the 11d code was protected with an "if (priv->enable11d)" clause.
But there was no code that anywhere that was able to set this
variable to true. So all 11d code was dead for almost a year and no one
complained. That's enought incentive to remove this code.

Besides removing old cruft, we gain back the 11d capability in a common way
when we merge the cfg80211 functionality.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: Fix TX status reporting in order to have proper rate control

First, we reduce the number of hardware retries to 0 (ie 2 real retries
for each rate). Next, when we report the retries to mac80211, we always
report a retry count of 1 (it seems to be 2 in fact, but using 2 seems
to lead to wrong performance for some reason). We use a state machine to
determine the real fate of a packet based on the 802.11 ACK and what the
Zydas hardware is saying when a real retry occurs. The real retry rates
are encoded in a static array. It has been tested with both zd1211 and
zd1211b hardware. Of course, since the Zydas hardware is not reporting
retries accurately, we are just doing our best in order to get the best
performance (ie higher throughput).

Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: use ieee80211_rx_ni()

Use the new ieee80211_rx_ni() function instead of ieee80211_rx().  Since we
use a workqueue to handle the RX path, we need to call the new function,
which disables bottom half handling.  This patch fixes the NOHZ:
local_softirq_pending messages.

CC: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mesh: use set_bit() to set MESH_WORK_HOUSEKEEPING.

This makes the mesh housekeeping timer work properly on big endian
systems.

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: don't filter BlockACK frames

The current A-MPDU tx_status report mechanism is too inaccurate.
With this patch BlockACK frames show now up to the driver and
can be processed.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170usb: atomic pending urbs counter

This patch follows "ar9170: atomic pending A-MPDU counter"
idea and converts another critical counter to atomic_*.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: atomic pending A-MPDU counter

A ref-counting bug emerged after testing ar9170usb's HT
implementation on a bigger SMP/SMT system without the usual
_debugging_ overhead.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: rework for static power save

For static power save, the actual intervals are calculated by driver based on
the default table and DTIM flag, then sent to uCode when the scheme
is changed.

Three tables are defined based on DTIM period.
1. DTIM 0 - 2
2. DTIM 3 - 10
3. DTIM > 11

The actual number of DTIM a station may miss may not exceed the
following:
. Only 1 DTIM may be skipped at PI=4 when allowed
. Only 2 DTIMs may be skipped at PI=5 when allowed
. DTIM may be skipped only 5 sec after last activity
. DTIM may be skipped only 30 sec after connection establishment

Only allow user to override the power_level when rf is ready to make sure
power level gets changed upon request.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: no chain noise support for 6x50 series

For initial bring up of 6x50 series NICs, no chain noise support in
uCode, this feature will be added in the later stage of development.

Two chain noise related functions are removed from 6x50 series:
1. gain computation
2. chain noise reset

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: set auto clock gate disable bit for 6x00/6x50 series

For 6x00 and 6x50 series NIC with OTP shadow RAM, set auto clock gate
disable bit when initializing OTP access.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: store station rate scale information in mac80211 station structure

Currently mac80211 initializes the rate scaling before notifying the driver
of the station's existence. The driver dealt with this by not relying on
mac80211's station notifications and instead mixing this functionality with
the rate scaling code and other places. To clean this up the driver needs
to do rate scaling initialization after being notified of the station, this
can be done if the rate scaling information forms part of the station
information passed from mac80211 to driver.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: move rate scaling structures to header file

Move to header file so they can be included and used in other parts of the
driver.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: move iwl_setup_mac to iwlagn

This function is only used in iwlagn so there is no need to have it in
iwlcore.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix incorrect otp blocks number for 6x50 series

For 6x50 series, number of OTP blocks is different from 6x00 series

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: identify eeprom version for 6x50 series NIC

Adding support for 6x50 series EEPROM version check, 6x50 is wifi/wimax
combo device which has different EEPROM map

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: show current power save status reported by uCode

Power save request is sent from driver to uCode, but there is no
indication from uCode about the current device power save state.

Reading GP_CNTRL register bit 25:24 to show the current power save
status

00: no power save
01: MAC power down
10: PHY power down
11: Error

The uCode could switch in and out of power save mode in the order of
once per 100-300 ms in many cases. The reading here should just be used for
reference on the current uCode power save status. Do not confuse this
reading with the PowerSave set by driver and mac80211.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: disable all tx fifos

Disable the all the tx fifos while stopping the tx queues.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: re-disable PG10 chips

"wl1251: add support for PG11 chips." accidentally enabled PG10 chips as
well...

Reported-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: use ieee80211_rx_ni()

Convert to new use ieee80211_rx_ni() routine rather than open-coded
version.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove unused lbs_cmd_802_11_inactivity_timeout()

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: make lbs_get_channel() static

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: harmonize cmd.h

* move declarations for functions of cmd.c/cmdresp.c into cmd.h
* move declarations from cmd.h that are in main.c to decl.h
* group command functions

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: cleanup host.h and hostcmd.h

Also remove some unused definitions and make tab usage consistent.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: handle coexistence radio notification

Handle WiFi/WiMax coexistence radio preemption notification event.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Set wiphy firmware version

Our wiphy firmware version is a combination of the UMAC and LMAC ones.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Support unexpected reboot barker

We can receive unexpected reboot barker at any time, and we're supposed to
reset the whole device then.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Try shared auth when open WEP fails

When we fail to associate with an open WEP AP, we fall back to shared auth.
This allows us to support joining a shared auth WEP AP with iwconfig.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Do not handle wifi command if the interface is not ready

When resetting or bringing the interface down, we should just reject any wifi
related command.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Check for cmd pointer before dereferencing it

The wifi_if_wrapper notification handling code uses a cmd pointer without
checking if it's valid or not. We're dereferencing it because we assume that
we only get to that point if there was a pending command for us. That's not
always true, so we'd better check.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: SDIO disable race fix

When calling sdio->bus_disable(), we are flushing the command lists before
disabling the sdio function. We can thus potentially get a command response
after having flushed the command list.
To avoid that race, we have to call iwm_reset() after disabling the sdio
function.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Tx power setting

We can now set the Tx power from e.g. iwconfig.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Update fixed size config definitions

We need to be in sync with the latest firmware API.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Update statistics notification structure

The latest firmware adds a ht_rates and a chain_energy field. The latter is
needed as we want to eventually support RSSI/antenna handling.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Improve rx debug

We display the correct DROP/RELEASE string for each rx packets, and when
it's dropped we also display the reason.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Profile flags can be WPA1 or WPA2 not both

UMAC will ASSERT if the profile security flag is WPA1 | WPA2, so we can only
accept one of those.
Moreover wpa_s wext and nl80211 drivers dont try to send WPA1 | WPA2, but only
one at a time.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: CT kill support

We set the initial CT (Temperature control) value to 110 degrees.
If the chip goes over that threshold, we hard block the device which will turn
it down. At the same time we schedule a 30 seconds delayed work that unblock
the device (and userspace is supposed to bring it back up), hoping that the
chip will have cooled down by then...

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: WPS support

By setting the WSC profile flag, we now support WPS as an enrollee.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: allow joining an existed IBSS network

We used to only support creating a new IBSS network. Now joining to
an existed IBSS network is supported as well.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: add BGN sdio device id

Add BGN SKU sdio device id.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Learn about mesh portals from multicast traffic

Mesh portals proxy traffic for nodes external to the mesh.  When a
proxied frame is received by a mesh interface, it should update its mesh
portal table.  This was only happening for unicast frames.  With this
change we also learn about mesh portals from proxied multicast frames.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement support for rt2800pci

Add support for the rt2860/rt3090 chipsets from Ralink.

Includes various patches from a lot of people who helped
getting this driver into the current shape.

Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Mark Asselstine <asselsm@gmail.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add rt2x00soc bus module

Add new library module for SoC drivers.
This is needed to fully support the platform
driver part of rt2800pci.

Based on original patch from Felix.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: use ieee80211_rx_ni()

Because of SPI and SDIO wl1251 does everything in a workqueue, including
calling ieee80211_rx() which should be called with bottom halves disabled.
An error message is emitted because of this:

NOHZ: local_softirq_pending 08

Fix this by using ieee80211_rx_ni().

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add ieee80211_rx_ni()

ieee80211_rx() must be called with bottom halves disabled. To simplify
driver development implement ieee80211_rx_ni() which disables BH. This
function must be used when in process context.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Optimize PIO scratchbuffer usage

This optimizes the PIO scratchbuffer usage.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: add support for PG11 chips.

This simple patch adds support for the PG11 variant of the WL1251 chip as
used on the OpenPandora OMAP3 device.

Signed-off-by: David-John Willis <John.Willis@Distant-earth.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: added missing packed modifier in some cmd structs

Some of the struct definitions in the wl1271_acx.h file were missing the
__attribute__ ((packed)) modifier.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: fix endianess issues

We were not handling endianess correctly.  The wl1271 chip runs on
little-endian values.  This patch makes sure that all the communication with
the wl1271 firmware is done in little-endian by using cpu_to_le* and
le*_to_cpu where appropriate.

Also, all the struct definitions for data exchanged with the firmware has
been changed to use __le16/32 types instead of u16/32.

This fixes a few sparse warnings, such as these:

drivers/net/wireless/wl12xx/wl1271_cmd.c:554:42: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:555:42: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:577:58: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:579:58: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:676:18: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:787:22: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:789:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_tx.c:98:47: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_acx.c:932:32: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_boot.c:191:32: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_boot.c:197:38: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_boot.c:199:37: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_init.c:255:40: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_init.c:275:53: warning: incorrect type in assignment (different base types)

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: added missing packed modifier in some acx structs

Some of the struct definitions in the wl1271_acx.h file were missing the
__attribute__ ((packed)) modifier.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: fix sparse warnings about undeclared functions

The following sparse warnings were fixed:

drivers/net/wireless/wl12xx/wl1271_spi.c:199:6: warning: symbol 'wl1271_spi_read_busy' was not declared. Should it be static?
drivers/net/wireless/wl12xx/wl1271_cmd.c:84:5: warning: symbol 'wl1271_cmd_cal_channel_tune' was not declared. Should it be static?
drivers/net/wireless/wl12xx/wl1271_cmd.c:107:5: warning: symbol 'wl1271_cmd_cal_update_ref_point' was not declared. Should it be static?
drivers/net/wireless/wl12xx/wl1271_cmd.c:132:5: warning: symbol 'wl1271_cmd_cal_p2g' was not declared. Should it be static?
drivers/net/wireless/wl12xx/wl1271_cmd.c:153:5: warning: symbol 'wl1271_cmd_cal' was not declared. Should it be static?

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Set IEEE80211_FCTL_TODS in the null data template

Set the IEEE80211_FCTL_TODS bit in the FC of the null data template.
This is a mandatory requirement in specification.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Cc: Vidhya Govindan <vidhya.govindan@nokia.com>
Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: replace netif_tx_{start,stop,wake}_all_queues

Replace netif_tx_{start,stop,wake}_all_queues with the single-queue
equivalents (i.e. netif_{start,stop,wake}_queue).  Since we are down to
a single queue, these should peform slightly better.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: use noise calibration from madwifi hal

This updates ath5k to calibrate the noise floor similar to the
way it is done in the madwifi hal and ath9k.  Of note:

- we start NF measurement at the same time as AGC calibration,
  but do not actually read the value until the periodic (long)
  calibration
- we keep a history of the last few values read and write the
  median back to the hardware for CCA
- we do not complain if NF calibration isn't complete, instead
  we keep the last read value.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: adjust ahb callbacks to new struct layout to avoid compile errors

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: make __lbs_cmd_async() non-static

This function will be needed for the cfg80211-enabled libertas driver.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: rename spi device to wl1251

During rename of the driver from wl12xx to wl1251 the spi device name
was accidentally left as wl12xx. Rename it to wl1251 which is the proper
name of the driver.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: remove warning in deauth case

It might be the case that __cfg80211_disconnected() has already
cleaned up wdev->current_bss() for us. The old code didn't catch
that situation and didn't warn needlessly.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: no cookies in cfg80211_send_XXX()

Get rid of cookies in cfg80211_send_XXX() functions.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix filter configuration

Fix the filter configuration to properly work with the two phase filter
configuration (prepare_multicast/configure_filter.)

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: make sure PS is disabled in PLT

We cannot be in PS mode when running PLT tests, so we need to make sure we're
in active mode.  Also, we need to clear up the rx_counter when we stop PLT,
otherwise it could cause problems when entering PLT again.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Correct memory handling for FW boot

Several memory allocation related failure cases were not properly
handled by the driver - the result was that in low memory conditions
booting of a corrupted FW could be attempted - and user space would not
get proper failure code.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Remove unnecessary rx_descriptor memory allocation

Remove unnecessary RX descriptor memory allocation from the driver. The
allocation was a remnant of the wl1251 driver.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Support for IPv4 ARP filtering

Add support for IPv4 ARP filtering in the driver. This will dramatically
reduce the number of unnecessary interrupts by the device in conqested
networks.

This patch is based on a similar patch to wl1251 by Janne Ylälehto.

Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix event handling mechanism

The event handling mechanism could miss events if multiple events would
occur simultaneously. Fix event handling mechanism to process all
events.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix multicast list handling

Fixes bugs in the multicast list handling:
 - Use atomic memory allocation in non-sleepable context
 - Increment address pointer when iterating list of MC addresses

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Checking of rx descriptor status fixed

Fixed checking of status of the received packet. On wl1251 status is in the
flags field of the descriptor, on wl1271 there is a separate status field.

Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Added 5 GHz support to join and rx

Added support to assiociate and use connection on 5 GHz band (802.11a).

Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Added support to scan on 5 GHz band

Added support to scan 802.11a access points on 5 GHz band when using
wl1273 chip.

Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Scan only enabled channels

Added checking of whether channel is enabled or disabled by mac80211
stack to scan. Disabled channels are not scanned.

Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Added 5 GHz parameters for wl1273

Added data rate and frequency tables for 5 GHz band channels, 5
GHz radio configration parameters and configuration option to enable
802.11 support.

Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Remove busy-word checking

Remove busy-word checking to work around an SPI bug. To reduce the
chance of chipset-busy scenarios, increment the number of fixed busy
words.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Implement beacon early termination support

Add support to enable beacon early termination in the firmware. Early
Beacon termination is a feature which allows the radio to be turned off
after TIM IE to save power.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>