Tony Lindgren [Fri, 8 Oct 2010 17:23:44 +0000 (10:23 -0700)]
omap: Update omap2plus_defconfig to use ttyO instead ttyS
With the omap-serial the device has changed from ttyS to ttyO as
the system may have both omap-serial and 8250 ports.
Note that systems using omap-serial need to be updated to use ttyO[012]
instead of ttyS[012] in the bootloader, CONFIG_CMDLINE, /etc/inittab,
and the root file system with mknod. Also you may need to add ttyO[012]
to /etc/securetty.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin Hilman [Fri, 8 Oct 2010 17:23:32 +0000 (10:23 -0700)]
OMAP2: PM: check UART status before trying to idle
As is done on OMAP3, check omap_uart_can_sleep() as one of the
pre-conditions for entering the idle loop. Without this check,
entering idle introduces large latencies on active UARTs, and is
especially noticable on serial console.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rajendra Nayak [Fri, 8 Oct 2010 17:23:22 +0000 (10:23 -0700)]
omap: hwmod: Handle modules with 16bit registers
Some modules which have 16bit registers can cause imprecise
aborts if a __raw_readl/writel is used to read/write 32 bits.
Add an additional flag to identify modules which have such
hard requirement, and handle it in the hwmod framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nicolas Kaiser [Fri, 8 Oct 2010 17:23:14 +0000 (10:23 -0700)]
arm/omap: remove duplicated include
Remove duplicated include.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Charulatha V [Fri, 8 Oct 2010 17:23:06 +0000 (10:23 -0700)]
OMAP2PLUS: WDT: Fix: Disable WDT after reset during init
Inorder to avoid any assumptions from bootloader, the watchdog
timer module is reset during init. This enables the watchdog
timer.
Therefore, it is required to disable WDT after it is reset
during init. Otherwise the system would reboot as per the default
watchdog timer registers settings.
Later, when the watchdog driver is loaded, the watchdog timer settings
is adjusted as per the default timer_margin set in the driver and the
driver would supports the normal operations supported by OMAP watchdog
timer.
Signed-off-by: Charulatha V <charu@ti.com>
Reported-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enric Balletbo i Serra [Fri, 8 Oct 2010 17:22:57 +0000 (10:22 -0700)]
omap3: Remove VMMC2 regulator on IGEP v2
VMMC2 regulator is configured but it's not used for the IGEP v2, so
remove this regulator from board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enric Balletbo i Serra [Fri, 8 Oct 2010 17:22:51 +0000 (10:22 -0700)]
omap3: Add i2c eeprom driver to read EDID on IGEP v2
Add i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enric Balletbo i Serra [Fri, 8 Oct 2010 17:22:43 +0000 (10:22 -0700)]
omap3: Fix handling some GPIO's for WLAN-BT combo on IGEP v2
Some GPIO's used by WLAN-BT combo on IGEP v2 depends on hardware
revision. This patch handles these GPIO's.
----------------------------------------------------------
| Hw Rev. | WIFI_NPD | WIFI_NRESET | BT_NRESET |
----------------------------------------------------------
| B | gpio94 | gpio95 | - |
| B/C (B-compatible) | gpio94 | gpio95 | gpio137 |
| C | gpio138 | gpio139 | gpio137 |
----------------------------------------------------------
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enric Balletbo i Serra [Fri, 8 Oct 2010 17:22:35 +0000 (10:22 -0700)]
omap3: Introduce function to detect the IGEP v2 hardwarerevision
There are currently two versions of IGEP v2 board, this patch introduces a
function to detect the hardware revision of IGEP board.
--------------------------
| Id. | Hw Rev. | GPIO 28 |
--------------------------
| 0 | B/C | high |
| 1 | C | low |
--------------------------
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enric Balletbo i Serra [Fri, 8 Oct 2010 17:22:28 +0000 (10:22 -0700)]
omap3: fix and improve the LED handling on IGEP v2 board
The IGEP v2 board has four leds, this patch allows control all
of these LEDs using the LED class if CONFIG_LEDS_GPIO is selected
or using the General Purpose Input/Output (GPIO) interface if
CONFIG_LEDS_GPIO is not selected.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enric Balletbo i Serra [Fri, 8 Oct 2010 17:22:19 +0000 (10:22 -0700)]
omap3: Add external VBUS power switch and overcurrent detect onIGEP v2 board
GPIO for various devices are missing from the board initialization.
This patch adds support for the VBUS and over current gpios. Without this
patch, input/outputs from these two sources are ignored.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enric Balletbo i Serra [Fri, 8 Oct 2010 17:22:11 +0000 (10:22 -0700)]
omap3: Add minimal OMAP3 IGEP module support
The OMAP3 IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family. More about this
board at www.igep.es.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated for the mmc changes and to be selected by default]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Fri, 8 Oct 2010 17:20:40 +0000 (10:20 -0700)]
Merge branch 'pm-hwmods' of ssh:///linux/kernel/git/khilman/linux-omap-pm into omap-for-linus
Tony Lindgren [Fri, 8 Oct 2010 17:19:53 +0000 (10:19 -0700)]
Merge branches 'devel-omap1' and 'devel-omap2plus' into omap-for-linus
Tony Lindgren [Fri, 8 Oct 2010 17:19:36 +0000 (10:19 -0700)]
Merge branch 'pm-next-2' of ssh:///linux/kernel/git/khilman/linux-omap-pm into omap-for-linus
Manjunath Kondaiah G [Fri, 8 Oct 2010 17:01:13 +0000 (10:01 -0700)]
OMAP3: Keypad: Fix incorrect type initializer
The keypad matrix variable declaration is not matching
with structure variable keymap declared in keypad_matrix.h.
Due to this, following sparse warnings are generated with omap3_defconfig.
arch/arm/mach-omap2/board-devkit8000.c:223:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-devkit8000.c:223:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-devkit8000.c:223:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-ldp.c:107:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-ldp.c:107:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-ldp.c:107:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3evm.c:472:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3evm.c:472:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3evm.c:472:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-3430sdp.c:114:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-3430sdp.c:114:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-3430sdp.c:114:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-cm-t35.c:568:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-cm-t35.c:568:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-cm-t35.c:568:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3stalker.c:415:13: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3stalker.c:415:13: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3stalker.c:415:13: got int static [toplevel] *<noident>
This patch modifies the variable keymap declaration as per declaration in matrix_keymap structure.
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-input@vger.kernel.org
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Manjunath Kondaiah G [Fri, 8 Oct 2010 17:00:19 +0000 (10:00 -0700)]
OMAP: plat-omap: Fix static function warnings
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/plat-omap/sram.c:130:13: warning: symbol 'omap_detect_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:216:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:450:12: warning: symbol 'omap_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:348:12: warning: symbol 'omap242x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:369:12: warning: symbol 'omap243x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:425:12: warning: symbol 'omap34xx_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:441:12: warning: symbol 'omap44xx_sram_init' was not declared. Should it be static
arch/arm/plat-omap/mcbsp.c:36:6: warning: symbol 'omap_mcbsp_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:50:5: warning: symbol 'omap_mcbsp_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:65:6: warning: symbol 'omap_mcbsp_st_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:70:5: warning: symbol 'omap_mcbsp_st_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:1648:15: warning: symbol 'omap_st_add' was not declared. Should it be static?
arch/arm/plat-omap/fb.c:414:15: warning: symbol 'omapfb_reserve_sram' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:43:5: warning: symbol 'omap_verify_speed' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:61:14: warning: symbol 'omap_getspeed' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Manjunath Kondaiah G [Fri, 8 Oct 2010 16:59:20 +0000 (09:59 -0700)]
OMAP: mach-omap2: Fix miscellaneous sparse warnings
This patch fixes miscellaneous sparse warnings in mach-omap2.
arch/arm/mach-omap2/board-am3517evm.c:141:17: warning: Initializer entry defined twice
arch/arm/mach-omap2/board-am3517evm.c:142:18: also defined here
arch/arm/mach-omap2/irq.c:50:35: warning: Using plain integer as NULL pointer
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Manjunath Kondaiah G [Fri, 8 Oct 2010 16:58:35 +0000 (09:58 -0700)]
OMAP2plus: Fix static function warnings
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Manjunath Kondaiah G [Fri, 8 Oct 2010 16:56:37 +0000 (09:56 -0700)]
OMAP: mach-omap2: Fix static declaration warnings
This patch fixes sparse warnings due to non declaration of
static structures and variables.
Sparse warning logs fixed:
arch/arm/mach-omap2/control.c:88:6: warning: symbol 'omap3_secure_ram_storage' was not declared. Should it be static?
n
arch/arm/mach-omap2/timer-gp.c:50:22: warning: symbol 'gptimer_wakeup' was not declared. Should it be static?
arch/arm/mach-omap2/timer-gp.c:240:18: warning: symbol 'omap_timer' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:121:24: warning: symbol 'prcm_context' was not declared. Should it be static?
arch/arm/mach-omap2/mux2420.c:510:29: warning: symbol 'omap2420_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux2430.c:589:29: warning: symbol 'omap2430_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:934:28: warning: symbol 'omap3_cus_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1080:29: warning: symbol 'omap3_cus_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1272:28: warning: symbol 'omap3_cbb_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1393:29: warning: symbol 'omap3_cbb_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1603:28: warning: symbol 'omap36xx_cbp_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1821:29: warning: symbol 'omap36xx_cbp_ball' was not declared. Should it be static?
arch/arm/mach-omap2/pm-debug.c:165:15: warning: symbol 'pm_dbg_dir' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:587:30: warning: symbol 'ads7846_config' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:606:23: warning: symbol 'omap3evm_spi_board_info' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:46:25: warning: symbol 'rx51_sdrc_params' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:211:25: warning: symbol 'rx51_get_sdram_timings' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3touchbook.c:64:15: warning: symbol 'touchbook_revision' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:350:24: warning: symbol 'am3517_evm_dss_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3stalker.c:567:23: warning: symbol 'omap3stalker_spi_board_info' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Manjunath Kondaiah G [Fri, 8 Oct 2010 16:56:11 +0000 (09:56 -0700)]
OMAP: mach-omap2: Fix incorrect assignment warnings
This patch fixes below sparse warnings for incorrect assignments.
arch/arm/mach-omap2/control.c:195:16: warning: incorrect type in assignment (different address spaces)
arch/arm/mach-omap2/control.c:195:16: expected unsigned int [usertype] *v_addr
arch/arm/mach-omap2/control.c:195:16: got void [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/control.c:199:25: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/control.c:199:25: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/control.c:199:25: got unsigned int [usertype] *
arch/arm/mach-omap2/control.c:320:28: warning: incorrect type in assignment (different address spaces)
arch/arm/mach-omap2/control.c:320:28: expected void *[noderef] <asn:2>scratchpad_address
arch/arm/mach-omap2/control.c:320:28: got void [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/control.c:321:9: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/control.c:321:9: expected void volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/control.c:321:9: got void *[noderef] <asn:2>scratchpad_address
arch/arm/mach-omap2/control.c:324:9: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/control.c:324:9: expected void volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/control.c:324:9: got void *
arch/arm/mach-omap2/control.c:327:9: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/control.c:327:9: expected void volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/control.c:327:9: got void *
arch/arm/mach-omap2/control.c:334:9: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/control.c:334:9: expected void volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/control.c:334:9: got void *
arch/arm/mach-omap2/control.c:321:9: warning: dereference of noderef expression
arch/arm/mach-omap2/control.c:324:9: warning: dereference of noderef expression
arch/arm/mach-omap2/control.c:327:9: warning: dereference of noderef expression
arch/arm/mach-omap2/control.c:334:9: warning: dereference of noderef expression
arch/arm/mach-omap2/pm34xx.c:323:28: warning: incorrect type in assignment (different address spaces)
arch/arm/mach-omap2/pm34xx.c:323:28: expected unsigned int [usertype] *scratchpad_address
arch/arm/mach-omap2/pm34xx.c:323:28: got void [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/pm34xx.c:326:26: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/pm34xx.c:326:26: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/pm34xx.c:326:26: got unsigned int [usertype] *
arch/arm/mach-omap2/pm34xx.c:329:26: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/pm34xx.c:329:26: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/pm34xx.c:329:26: got unsigned int [usertype] *
arch/arm/mach-omap2/pm34xx.c:334:29: warning: incorrect type in argument 1 (different address spaces)
arch/arm/mach-omap2/pm34xx.c:334:29: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap2/pm34xx.c:334:29: got unsigned int [usertype] *
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 4 Oct 2010 23:58:01 +0000 (16:58 -0700)]
omap: Keep nwires for omap1 and 2420 MMC controller
A patch from Sukumar Ghorai <s-ghorai@ti.com> changed the
nwires to use caps instead. However, nwires is still
needed for the earlier controller.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Janusz Krzysztofik [Fri, 1 Oct 2010 23:37:01 +0000 (16:37 -0700)]
OMAP1: Amstrad Delta: add camera controlled LEDS trigger
This patch extends the Amstrad Delta camera support with LEDS trigger that can
be used for automatic control of the on-board camera LED. The led turns on
automatically on camera device open and turns off on camera device close.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Janusz Krzysztofik [Fri, 1 Oct 2010 23:37:00 +0000 (16:37 -0700)]
OMAP1: Amstrad Delta: add support for camera
This patch adds configuration data and initialization code required for camera
support to the Amstrad Delta board.
Three devices are declared: SoC camera, OMAP1 camera interface and OV6650
sensor.
Default 12MHz clock has been selected for driving the sensor. Pixel clock has
been limited to get reasonable frame rates, not exceeding the board
capabilities. Since both devices (interface and sensor) support both pixel
clock polarities, decision on polarity selection has been left to drivers.
Interface GPIO line has been found not functional, thus not configured.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Janusz Krzysztofik [Fri, 1 Oct 2010 23:37:00 +0000 (16:37 -0700)]
OMAP1: Add support for SoC camera interface
This patch adds a definition of the OMAP1 camera interface platform device,
and a function that allows for providing a board specific platform data.
The device will be used with the upcoming OMAP1 SoC camera interface driver.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
kishore kadiyala [Fri, 1 Oct 2010 23:35:28 +0000 (16:35 -0700)]
omap4 hsmmc: Update ocr mask for MMC2 for regulator to use
On OMAP4, MMC2 controller has eMMC which draws power from VAUX regulator
on TWL. Though the eMMC supports dual voltage[1.8v/3v] as per ocr register,
its VCC is fixed at 3V for operation. With this once the mmc core selects
the minimum voltage[1.8] supported based on the ocr value read from OCR register,
eMMC will not get detected. Thus the platform data for MMC2 is updated with ocr
mask and same will be communicated to core which will set the regulator to
always operate at 3V when ever turned ON.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
kishore kadiyala [Fri, 1 Oct 2010 23:35:28 +0000 (16:35 -0700)]
omap4 hsmmc: Register offset handling
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Benoit Cousson [Fri, 1 Oct 2010 23:35:26 +0000 (16:35 -0700)]
omap4 hsmmc: Fix the init if CONFIG_MMC_OMAP_HS is not set
Avoid possible crash if CONFIG_MMC_OMAP_HS is not set
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Madhusudhan Chikkature [Fri, 1 Oct 2010 23:35:25 +0000 (16:35 -0700)]
OMAP4 ES2: HSMMC soft reset change
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Grazvydas Ignotas [Fri, 1 Oct 2010 23:35:25 +0000 (16:35 -0700)]
omap: pandora: enable twl4030 charger
Add platform data to make use of newly added charging driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Grazvydas Ignotas [Fri, 1 Oct 2010 23:35:25 +0000 (16:35 -0700)]
omap: pandora: add fixed regulator for wlan
Instead of enabling the wifi module explicitly using GPIO, add a fixed
regulator and hook it to MMC host card power control. This way it will
only be enabled when SDIO subsystem wants to talk to it, saving power
(as done by Zoom boards).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sanjeev Premi [Fri, 1 Oct 2010 23:35:24 +0000 (16:35 -0700)]
omap2/3: Update revision identification
The existing definitions for cpu revision used
upper nibble in the bits[15:08]. With OMAP3630,
definitions use lower nibble.
This patch unifies the definitions to start
at lower nibble.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Fri, 1 Oct 2010 23:35:24 +0000 (16:35 -0700)]
omap: Fix omap_mux_init_signal not to trash muxname
Otherwise the muxname passed to the function will get truncated.
Based on an earlier patch by rockefeller.lin@innocomm.com.
Reported-by: rockefeller.lin@innocomm.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Loïc Minier [Mon, 27 Sep 2010 21:04:20 +0000 (23:04 +0200)]
OMAP: PM: Fix build when CONFIG_PM_DEBUG isn't set
Since
6cdee91257bee23a46dc869ca62469b67cba2c7e the references to
enable_off_mode and sleep_while_idle can't be resolved when CONFIG_PM_DEBUG
isn't set:
arch/arm/mach-omap2/built-in.o: In function `omap_uart_restore_context':
arch/arm/mach-omap2/serial.c:253: undefined reference to `enable_off_mode'
arch/arm/mach-omap2/built-in.o: In function `omap3_can_sleep':
arch/arm/mach-omap2/pm34xx.c:479: undefined reference to `sleep_while_idle'
Simply #define these in pm.h just like omap2_pm_debug.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
[khilman: moved down into existing #ifdef section]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Fri, 1 Oct 2010 15:35:47 +0000 (08:35 -0700)]
OMAP3: CPUidle: remove redundant setting of PER next power state
When checking how to program the next powerstate for the PER
powerdomain, the next state of PER powerdomain was written twice.
Remove the duplicate write.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Fri, 1 Oct 2010 20:24:10 +0000 (13:24 -0700)]
manual merge for pm-hwmod-uart due to conflicts
Kevin Hilman [Fri, 1 Oct 2010 20:24:09 +0000 (13:24 -0700)]
Merge branch 'pm-hwmod-wdog' into pm-hwmods
Govindraj.R [Mon, 27 Sep 2010 14:51:05 +0000 (20:21 +0530)]
OMAP3: SERIAL: Initialize all omap-uarts for zoom boards
Initialize all omap-uarts for zoom boards. Now zoom_peripheral_init
will initialise all uarts for 3630. 3630sdp_board_init call
zoom_peripheral_init so we can now remove serial_init from 3630sdp
board init as zoom_peripheral_init now will do that the same.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Govindraj.R [Mon, 27 Sep 2010 14:50:57 +0000 (20:20 +0530)]
OMAP: SERIAL: Enable omap-serial driver in Kconfig
Enable omap-serial driver in /mach-omap2/Kconfig and
move 8250 driver selection for zoom boards. With omap-serial
driver addition all omap-uarts can be handled with
omap-serial driver.
With addition of omap-serial driver console parameter
needs be changed in bootargs from ttyS* should be
replaced with ttyO* [O --> OMAP not ZERO]
For example: ttyS0[UART1 on 3430SDP] changes to ttyO0.
But with some boards that do not use omap-uart as console uart.
we need to handle them with 8250 driver. Ex: ZOOM2/3.
For zoom2/3 board we need to use 8250 serial driver and
console parameter will remain ttyS0 which basically uses
a Quad uart placed on the debug board connected through a
gpio line.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Govindraj.R [Mon, 27 Sep 2010 14:50:49 +0000 (20:20 +0530)]
serial: Add OMAP high-speed UART driver
This patch adds driver support for OMAP2/3/4 high speed UART.
The driver is made separate from 8250 driver as we cannot
over load 8250 driver with omap platform specific configuration for
features like DMA, it makes easier to implement features like DMA and
hardware flow control and software flow control configuration with
this driver as required for the omap-platform.
This patch involves only the core driver and its dependent.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Govindraj.R [Mon, 27 Sep 2010 14:50:41 +0000 (20:20 +0530)]
OMAP3: serial: Fix uart4 handling for 3630
This patch makes the following:
- Adds missing wakeup padding register handling.
- Fixes a hardcode to use PER module ONLY on UART3.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Govindraj.R [Mon, 27 Sep 2010 14:50:32 +0000 (20:20 +0530)]
OMAP3: PM: Add prepare idle and resume idle call for uart4
Add prepare idle and resume idle call for uart4 used by 3630.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Govindraj.R [Mon, 27 Sep 2010 14:50:25 +0000 (20:20 +0530)]
OMAP3: PRCM: Consider UART4 for 3630 chip in prcm_setup_regs
To standarize among other uarts (1 to 3), we shall now:
- Enable uart4 autodile bit.
- Enable uart4 wakeup in PER.
- Allow uart4 to wakeup the MPU.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Govindraj.R [Mon, 27 Sep 2010 14:50:17 +0000 (20:20 +0530)]
OMAP clock: Add uart4_ick/fck definitions for 3630
This is only valid for omap 36xx family of chips.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 27 Sep 2010 14:50:06 +0000 (20:20 +0530)]
OMAP: UART: use non-locking versions of hwmod enable/idle functions
Since the UART enable/idle is done during the idle path (with
interrupts disabled), use the non-locking versions of the hwmod
enable/idle functions.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 27 Sep 2010 14:49:53 +0000 (20:19 +0530)]
OMAP: UART: don't do automatic bus-level suspend/resume
Since the omap_device for UART is currently managed inside the idle
path itself, don't let the bus-level code suspend/resume the UART.
To prevent this, pm_runtime_get() is used when preparing for suspend
and pm_runtime_put() is used when finished with suspend.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Govindraj.R [Mon, 27 Sep 2010 14:49:46 +0000 (20:19 +0530)]
OMAP2: UART: remove set_uart_globals
Remove set_uart_globals function as this will not be needed as
physical address for uarts will be taken from hwmod data file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 27 Sep 2010 14:49:38 +0000 (20:19 +0530)]
OMAP: UART: omap_device conversions, remove implicit 8520 assumptions
Major rework of OMAP UART init for omap_device conversion as well as
use with either 8250 driver or new omap-serial driver.
In preparation for a new omap-serial driver, remove 8250 assumptions
and dependencies from the serial core.
Convert UART core and PM support to use omap_device layer. Also add
support for both console on 8250 or omap-serial driver.
omap_device conversion:
- Convert clock API calls to omap_device calls
- Remove all static platform_data setup and configuration. This is
all done by the omap_device build phase.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 27 Sep 2010 14:49:30 +0000 (20:19 +0530)]
OMAP2/3: UART: add omap_hwmod data for UARTs 1-4
This patch adds omap_hwmod data for UARTs on OMAP2 and OMAP3
platforms.
UART4 support for 3630 and OMAP2 hwmod data added by Govindraj R.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Benoit Cousson [Mon, 27 Sep 2010 14:49:19 +0000 (20:19 +0530)]
OMAP4: UART: Add uart1-4 hwmods data for omap4
Add uart1-4 hwmod data into omap4_hwmod data file.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Varadarajan, Charulatha [Thu, 23 Sep 2010 14:32:43 +0000 (20:02 +0530)]
OMAP: WDT: Use PM runtime APIs instead of clk FW APIs
Call runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings instead of using
clock FW APIs.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Varadarajan, Charulatha [Thu, 23 Sep 2010 14:32:42 +0000 (20:02 +0530)]
OMAP: WDT: Split OMAP1 and OMAP2PLUS device registration
This patch splits omap_init_wdt() into separate omap_init_wdt()
functions under mach-omap1 and mach-omap2 and set them up with
subsys_initcall.
Also it uses omap_device_build() API instead of
platform_device_register() for watchdog timer device registration
for OMAP2plus chips.
For OMAP2plus chips, the device specific data defined in centralized
hwmod database will be used.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Benoit Cousson [Thu, 23 Sep 2010 14:32:41 +0000 (20:02 +0530)]
OMAP4: hwmod data: Add watchdog timer
Add watchdog timer hwmod data for OMAP4 chip
Note: wd_timer3 in enabled in the hwmod list but it is
not yet supported by the watchdog driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Varadarajan, Charulatha [Thu, 23 Sep 2010 14:32:40 +0000 (20:02 +0530)]
OMAP2430: hwmod data: Add watchdog timer
Add watchdog timer hwmod data for OMAP2430 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Varadarajan, Charulatha [Thu, 23 Sep 2010 14:32:39 +0000 (20:02 +0530)]
OMAP2420: hwmod data: Add watchdog timer
Add watchdog timer hwmod data for OMAP2420 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Varadarajan, Charulatha [Thu, 23 Sep 2010 14:32:38 +0000 (20:02 +0530)]
OMAP3: hwmod data: Add watchdog timer
Add watchdog timer hwmod data for OMAP3 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Tue, 28 Sep 2010 19:07:28 +0000 (19:07 +0000)]
OMAP2+: defconfig: disable CPUfreq
Disable CPUfreq since
1) is not yet supported in mainline, and
2) the current driver fails to suspend properly
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin Hilman [Tue, 28 Sep 2010 19:07:29 +0000 (19:07 +0000)]
OMAP2+: defconfig: modularize bluetooth, audio and WLAN
In working towards a smaller default kernel, only devices used for
early boot should be built in. Toward that end, build the following
as modules by default:
- bluetooth
- audio: ALSA, ASoC
- WLAN
Uncompressed kernel size comparison:
Before:
text data bss dec hex filename
6557576 465088
5616024 12638688 c0d9e0 vmlinux
After:
text data bss dec hex filename
5616572 436448
5610800 11663820 b1f9cc vmlinux
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tim Nordell [Mon, 27 Sep 2010 16:05:50 +0000 (16:05 +0000)]
ARM: OMAP3LOGIC: Added SMSC Ethernet board support
Enable SMSC911x Ethernet driver for LogicPD's OMAP
3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tim Nordell [Mon, 27 Sep 2010 16:05:49 +0000 (16:05 +0000)]
ARM: OMAP3LOGIC: Add generic smsc911x support when connected to GPMC
Introduce of a generic way to setup smsc911x based Ethernet
controller connected to GPMC similar to gpmc-smc91x but without
timing setup.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tim Nordell [Mon, 27 Sep 2010 16:05:48 +0000 (16:05 +0000)]
ARM: OMAP3LOGIC: Adding SDMMC support
Add low-level initialization for hsmmc controller for
LogicPD's OMAP 3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
[tony@atomide.com: updated for the recent mmc platform init changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tim Nordell [Mon, 27 Sep 2010 16:05:47 +0000 (16:05 +0000)]
ARM: OMAP3LOGIC: Adding LogicPD OMAP3 board support
Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
matt mooney [Tue, 28 Sep 2010 02:04:32 +0000 (19:04 -0700)]
arm: remove cast from void*
Unnecessary cast from void* in assignment.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Igor Grinberg [Tue, 21 Sep 2010 16:03:13 +0000 (16:03 +0000)]
omap3: cm-t3517: add support for TI HECC
add support for TI HECC.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Igor Grinberg [Tue, 21 Sep 2010 16:03:12 +0000 (16:03 +0000)]
omap3: cm-t3517: add support for NAND flash
add support for NAND flash.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Igor Grinberg [Tue, 21 Sep 2010 16:03:11 +0000 (16:03 +0000)]
omap3: cm-t3517: add support for usb host
add support for hsusb host ports 1, 2 and on-module usb hub.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Igor Grinberg [Tue, 21 Sep 2010 16:03:10 +0000 (16:03 +0000)]
omap3: cm-t3517: add support for v3020 rtc
add support for v3020 rtc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Igor Grinberg [Tue, 21 Sep 2010 16:03:09 +0000 (16:03 +0000)]
omap3: Introduce CompuLab CM-T3517 module
Add basic suppot, enable uart and led.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 27 Sep 2010 20:17:13 +0000 (13:17 -0700)]
Merge branch 'omap4_and_sdrc_2.6.27' of git://git.pwsan.com/linux-2.6 into omap-for-linus
Jon Hunter [Mon, 27 Sep 2010 20:02:59 +0000 (14:02 -0600)]
omap3: Prevent SDRC deadlock when L3 is changing frequency
When changing the L3 clock frequency, the CPU is executing from internal RAM
and the SDRC clock is disabled. During this time accesses made to external
DDR are stalled. If the ARM subsystem attempts to access the DDR while the
SDRC clock is disabled this will stall the CPU until the access to the SDRC
timeouts. A timeout on the SDRC should never occur. Once a timeout occurs all
the following accesses will be aborted and the DDR is no longer accessible.
Although the code being executed in the internal RAM does not directly access
the DDR, it was found that the branch prediction logic in the CPU may cause
the CPU to prefetch code from a DDR location while the SDRC clock is disabled.
This was causing an SDRC timeout which resulted in a system hang.
This patch fixes this problem by ensuring the branch prediction logic is
disabled while changing the L3 clock frequency. The branch prediction logic
is disabled by clearing the Z-bit in the ARM CTRL register.
Disabling the branch prediction logic does not have any noticable impact
on the execution time of this code section. The hardware observability
signals were used to monitor the sdrc idle time with and without this
patch when operating at different CPU frequencies (150MHz, 500MHz and
600MHz) and the total sdrc idle time when changing frequenct was in
the range of 9-11us. This was measured on an omap3430 SDP running the
omapzoom p-android-omap-2.6.29 branch.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Santosh Shilimkar [Mon, 27 Sep 2010 20:02:58 +0000 (14:02 -0600)]
omap4: control: Fix the control module register accesses
This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together
1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Santosh Shilimkar [Mon, 27 Sep 2010 20:02:58 +0000 (14:02 -0600)]
omap4: control: Add the register definition headers
On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP
This patch adds all the omap4 control module register data and
includes them in the common control.h
The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Santosh Shilimkar [Mon, 27 Sep 2010 20:02:57 +0000 (14:02 -0600)]
omap4: control: Add accessor api's for pad control module
On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.
This APIs will work only for OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Santosh Shilimkar [Mon, 27 Sep 2010 20:02:57 +0000 (14:02 -0600)]
omap4: control: Add ctrl_pad_base to omap_globals
On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE 0x4a002000
- CTRL_MODULE_PAD_CORE 0x4a100000
- CTRL_MODULE_WKUP 0x4a30c000
- CTRL_MODULE_PAD_WKUP 0x4a31e000
Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code
The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Benoit Cousson [Mon, 27 Sep 2010 20:02:56 +0000 (14:02 -0600)]
OMAP4: clocks: Fix ES2 clock issues
Fix a few OMAP4430 clock tree problems after the recent manual merge of the
various ES2 clock patches:
- usim optional clock and its parent had the same name, rename the parent
usim_fclk -> usim_ck
- OPTFCLKEN_CLK32K is not handled anymore by the USBPHYOCP2SCP module in ES2
Create a new clock that belongs to CM_ALWON_USBPHY_CLKCTRL register
This patch depends on some of the PRCM macro updates from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: tweaked patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Rajendra Nayak [Mon, 27 Sep 2010 20:02:56 +0000 (14:02 -0600)]
OMAP4: powerdomain: Update DSS logic state for ES2
DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Rajendra Nayak [Mon, 27 Sep 2010 20:02:56 +0000 (14:02 -0600)]
OMAP4: PM: Define additional registers for ES2
4430 ES2 has a few new registers added and a few modified
from ES1. This patch adds all the register changes in PRM
and CM for OMAP4430 ES2.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Rajendra Nayak [Mon, 27 Sep 2010 20:02:55 +0000 (14:02 -0600)]
OMAP4: CM & PRM: Update PRCM register bitshifts and masks for ES2
This patch updates the PRM and CM register bitshifts and masks
for OMAP4430 ES2.0.
Replace as well the BITFIELD macro with the shift operator in order
to be consistent with the previous OMAP2 & 3 format.
Sort the register list in comments in order to have a consistent
register order and avoid futur change during code generation.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Benoit Cousson [Mon, 27 Sep 2010 20:02:55 +0000 (14:02 -0600)]
OMAP4: clock: Add optional clock nodes
OMAP4 IP optional clocks require explicit enable in module CTRLCLK
register. In order to allow that we have to create artificial clock
nodes that represent this clock inputs in the IP.
Notes:
- Temporary use OMAP3 names for GPIO optional clocks until the GPIO hwmod
convertion is done. It will enforce the usage of OMAP4 names as the reference.
- Temporary use OMAP3 names for TIMER main clock (gptX_fck) until TIMER hwmod
convertion is done. During that convertion, the new name will have to be used.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Benoit Cousson [Mon, 27 Sep 2010 20:02:54 +0000 (14:02 -0600)]
OMAP4: clock: Fix clock names and align with hwmod names
The OMAP4 hwmod data introduced the new naming convention for TI
IPs (See patch OMAP4: hwmod: Add partial hwmod support for OMAP4430 ES1.0)
The leaf clock names are using the same IP name and thus must be
modified to match the clock populated in the hwmod data.
- Fix some leaf clocks nodes that were using a _iclk instead of the _fclk
prefix.
- Fix some wrong interface clock name for master IPs connected to
interconnect.
Please not that due to the fact that nodes are sorted by name, the name
change will introduce a quite ugly diff a little bit hard to follow.
Timers clock con_id is still using the old gptX_fck name until the
gptimer driver is updated to omap_device framework.
Timers entries in hwmods DB are still disabled until the migration
if timer to platform_driver + omap_hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: manually resolved conflicts with Rajendra's clock patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Rajendra Nayak [Mon, 27 Sep 2010 20:02:54 +0000 (14:02 -0600)]
OMAP4: clocks: Update clock tree for ES2
This patch updates the clock tree with all the
changes in OMAP4430 ES2.
clock nodes added
-1- tie_low_clock_ck
-2- abe_dpll_bypass_clk_mux_ck
clock nodes deleted
-1- dpll_sys_ref_clk
-2- per_sgx_fclk
-3- usbphyocp2scp_ick
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: added comment re ES1 clocks to top of file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Lennert Buytenhek [Wed, 22 Sep 2010 18:40:57 +0000 (20:40 +0200)]
update OMAP Kconfig help texts for all supported SoC models
update OMAP Kconfig help texts for all supported SoC models
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 27 Sep 2010 17:22:16 +0000 (10:22 -0700)]
Merge branch 'devel-omap-smp-on-up' into omap-for-linus
Tony Lindgren [Mon, 27 Sep 2010 17:19:44 +0000 (10:19 -0700)]
Merge branch 'devel-boards' into omap-for-linus
Tony Lindgren [Mon, 27 Sep 2010 17:18:00 +0000 (10:18 -0700)]
Merge branch 'misc_2.6.37' of git://git.pwsan.com/linux-2.6 into omap-for-linus
Tony Lindgren [Mon, 27 Sep 2010 17:15:47 +0000 (10:15 -0700)]
Merge branch 'devel-omap-misc' into omap-for-linus
Sukumar Ghorai [Wed, 15 Sep 2010 14:49:23 +0000 (14:49 +0000)]
omap: mmc: extended to pass host capabilities from board file
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Tue, 31 Aug 2010 10:12:56 +0000 (10:12 +0000)]
omap2: McBSP: Remove mux code for OMAP2420 McBSP2 and do cleanups
This 'legacy' OMAP2420 McBSP2 muxing code is currently broken after recent
conversion to new mux code. The omap_mcbsp_request calling this code is
usually called after booting whereas the omap_mux_init_signal is __init
marked so null pointer dereference would occur.
Fix this by removing the muxing code and let the bootloader or board file to
do it if necessary. Remove also omap2_mcbsp_ops as there is no use for it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Tue, 31 Aug 2010 08:11:44 +0000 (08:11 +0000)]
omap: McBSP: Do not enable SRG in slave mode
McBSP SRG (Sample Rate Generator) and FSG (Frame Sync
Generator) is only needed to be enabled, when McBSP
is master.
In McBSP slave mode, the SRG, and FSG can be kept disabled,
which might save some power at the end in this configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Subramaniam C.A [Tue, 24 Aug 2010 17:02:28 +0000 (12:02 -0500)]
omap: i2c: Avoid compilation error in case the header is included multiple times
Added defines to avoid compilation error.
Signed-off-by: Subramaniam C.A <subramaniam.ca@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Kasatkin [Fri, 20 Aug 2010 13:44:46 +0000 (13:44 +0000)]
omap: crypto: updates to enable omap aes
Updates to enable omap aes
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
[tony@atomide.com: updated to use CONFIG_ARCH_OMAP2/3 instead of old 24XX/34XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Anand Gadiyar [Thu, 16 Sep 2010 23:22:13 +0000 (16:22 -0700)]
omap: usb: fix build warning
Fix this and similar build warnings when building with
omap_4430sdp_defconfig.
CC arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ricardo Salveti de Araujo [Fri, 24 Sep 2010 01:22:49 +0000 (18:22 -0700)]
omap4: board-omap4panda: adding leds status1 and status2
At Pandaboard we have 2 status leds, so adding them with similar usage as
we have for Beagleboard (heartbeat and mmc0). The patch basically adds the
platform data required by leds-gpio driver.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Shubhrajyoti Datta [Fri, 24 Sep 2010 01:22:49 +0000 (18:22 -0700)]
omap: 4430sdp board support for proximity sensor
omap 4430sdp board support for the proximity sensor via GPIO keys.
The proximity sensor is connected to GPIO and is registered as a
GPIO key.
- Making the default state of the sensor off at bootup
- The init is called before platform_add_devices
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Fri, 24 Sep 2010 23:01:57 +0000 (16:01 -0700)]
Merge branch 'omap_for_2.6.37' of git://dev.omapzoom.org/santosh/kernel-omap4-base into omap-for-linus
Hema HK [Fri, 24 Sep 2010 16:23:19 +0000 (10:23 -0600)]
OMAP: hwmod: Set autoidle after smartidle during _sysc_enable
OMAP USBOTG module has a requirement to set the autoidle bit only after
setting smartidle bit. Modified the _sys_enable api to set the smartidle
first and then the autoidle bit. Setting this will not have any impact on the
other modules.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 24 Sep 2010 16:23:18 +0000 (10:23 -0600)]
OMAP4: PM: Declare idle modules as functional too
The omap4_cm_wait_module_ready function would only check for
the modules to be completely functional before declaring them
ready to be accessed.
There might also be instances where in the module is actually
in idle (under h/w control) but should still be declared
accessible, as the h/w control would make it functional when
needed.
Hence make omap4_cm_wait_module_ready return true in case
the module is fully functional *or* in idle state.
Fail only if the module is fully disabled or stuck intransition.
The explaination from the TRM for the idlest bits on OMAP4 is as
below for quick reference
Module idle state:
0x0 func: Module is fully functional, including OCP
0x1 trans: Module is performing transition: wakeup, or sleep, or sleep
abortion
0x2 idle: Module is in Idle mode (only OCP part). It is functional if
using separate functional clock
0x3 disabled: Module is disabled and cannot be accessed
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kishon Vijay Abraham I [Fri, 24 Sep 2010 16:23:18 +0000 (10:23 -0600)]
OMAP: omap_device: Fix to support multiple hwmods for a single device
Currently there is a bug in the existing omap_device core code when
extracting the hwmod structures passed to omap_device_build_ss(). This bug
gets exposed only when passing multiple hwmod structures to
omap_device_build_ss() resulting in incorrect extraction from second hwmod
structure.
This fix uses the pointer to pointer to omap_hwmod structure (array of
pointers to omap_hwmod structure) passed to omap_device_build_ss() to
correctly extract the appropriate omap_hwmod structure.
This patch has been created and tested on lo/master and mainline.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha V <charu@ti.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Santosh Shilimkar [Thu, 16 Sep 2010 13:14:48 +0000 (18:44 +0530)]
omap4: Fix bootup crash observed with higher CPU clocks
This patch is temporary fix to below crash. This is observed when
CPU is clocked more than 600 MHz.
Unhandled fault: imprecise external abort (0x1406) at 0xbf9ef65c
Internal error: : 1406 [#1] PREEMPT SMP
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.36-rc3+ #18)
PC is at kernel_thread_helper+0x0/0x14
LR is at kernel_thread_helper+0x0/0x14
pc : [<
c003ce14>] lr : [<
c003ce14>] psr:
00000093
sp :
dc83bff8 ip :
00000000 fp :
00000000
r10:
00000000 r9 :
00000000 r8 :
00000000
r7 :
00000013 r6 :
c003ce28 r5 :
c008935c r4 :
00000000
r3 :
00000000 r2 :
00000000 r1 :
00000000 r0 :
00000000
Flags: nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control:
10c53c7f Table:
8000404a DAC:
00000017
Process swapper (pid: 2, stack limit = 0xdc83a2f0)
Stack: (0xdc83bff8 to 0xdc83c000)
bfe0:
00000000 ffffffff
[<
c003ce14>] (kernel_thread_helper+0x0/0x14) from [<
fffffffe>] (0xfffffffe)
Code:
c03a0ba3 c03a5fcb c045c880 c0394035 (
eb017701)
---[ end trace
1b75b31a2719ed1c ]---
The timer hwmod adaptation will eventually fix it in a proper way.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
David Anders [Thu, 16 Sep 2010 13:14:47 +0000 (18:44 +0530)]
omap4: Panda: Add DEBUG_LL support
Add support for use of DEBUG_LL for use with PandaBoard.
Signed-off-by: David Anders <x0132446@ti.com>
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / log