Baruch Siach [Thu, 24 Jun 2010 08:57:03 +0000 (11:57 +0300)]
mx25: add PWM4 to iomux
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Thu, 24 Jun 2010 08:57:02 +0000 (11:57 +0300)]
mx25: add iomux defines for UART4 on KPP pins
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fabio Estevam [Mon, 21 Jun 2010 20:33:05 +0000 (13:33 -0700)]
mx31_3ds: Handle USB OTG GPIO Errors
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Mon, 21 Jun 2010 05:16:00 +0000 (08:16 +0300)]
mx25: add support for the CSI device
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Mon, 21 Jun 2010 05:15:59 +0000 (08:15 +0300)]
mx27: add support for the CSI device
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Luotao Fu [Fri, 18 Jun 2010 07:23:19 +0000 (09:23 +0200)]
pca100: clean up GPIO pin multiplexing
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding
pin multiplexing either into the initial pin config table or ifdef blocks.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Luotao Fu [Fri, 18 Jun 2010 07:23:18 +0000 (09:23 +0200)]
pca100: add framebuffer device support and TFT
this one adds the frambuffer device and a TFT panel to the PhyCard-S
(pca100) board.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Sat, 12 Jun 2010 14:22:39 +0000 (22:22 +0800)]
mxc/iomux: add GPIO bank offset for iomux v3 platforms
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Sat, 12 Jun 2010 14:22:38 +0000 (22:22 +0800)]
mx51/iomux: add UART and GPIO pad definitions for imx51_3ds board
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Sat, 12 Jun 2010 14:22:37 +0000 (22:22 +0800)]
mx51/iomux: Fix mux mode and input path for two pads
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Amit Kucheria [Wed, 16 Jun 2010 11:00:15 +0000 (14:00 +0300)]
[PATCH] mxc: Fix pad names for imx51
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Thu, 10 Jun 2010 14:07:50 +0000 (16:07 +0200)]
i.MX35: add cpuimx35 support and its baseboard
* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host,
USB OTG and I2C touchscreen controller
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Thu, 10 Jun 2010 09:14:32 +0000 (12:14 +0300)]
mx25: add a comment documenting undocumented IPG clocks
The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Wed, 9 Jun 2010 11:07:01 +0000 (14:07 +0300)]
mx25pdk: register watchdog device
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Thu, 10 Jun 2010 09:32:15 +0000 (12:32 +0300)]
mx25: add watchdog clock
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:03:01 +0000 (11:03 +0200)]
i.MX25: add cpuimx25 module and its baseboard
* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host
and USB OTG
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:03:00 +0000 (11:03 +0200)]
i.MX25: add AUDMUX and SSI support
* add clocks for audmux and ssi 1 & 2
* add irq for ssi 1 & 2
* add devices platform for ssi1 & 2
* update audmux-v2 for i.MX25
* add base addresses for audmux & ssi 1 & 2
* add iomux configuration for GPIO for AUD5 port
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:59 +0000 (11:02 +0200)]
i.MX25: fix USB gadget support
i.MX25's udc port is the same as i.MX35's one
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:58 +0000 (11:02 +0200)]
i.MX25: fix EHCI support
i.MX25's EHCI is the same as i.MX35's one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:57 +0000 (11:02 +0200)]
i.MX25: fix get_rate_otg to return the correct value
usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:56 +0000 (11:02 +0200)]
plat-mxc/ehci.c: add i.MX25 support
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:55 +0000 (11:02 +0200)]
MX25: put define for OTG base address in right include
the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 1 Jun 2010 19:57:44 +0000 (21:57 +0200)]
i.MX27: add suspend to RAM support
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Sun, 20 Jun 2010 19:22:54 +0000 (21:22 +0200)]
eukrea_mbimx27: fix audio support when SOC is compiled as module
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Fri, 18 Jun 2010 14:19:55 +0000 (16:19 +0200)]
mach-cpuimx27: fix USB_ULPI build warnings
when CONFIG_USB_ULPI is not defined we actually get :
warning: 'otg_pdata' defined but not used
warning: 'usbh2_pdata' defined but not used
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: s.hauer@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 16:07:05 +0000 (18:07 +0200)]
i.MX35: return IPU clock's value for mx3fb
without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Dinh Nguyen [Thu, 27 May 2010 15:45:05 +0000 (10:45 -0500)]
mx5: Register i2c on Freescale MX51 Babbage HW
Add device registration and setup IOMUX pins in the mx51_babbage
board feil.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Dinh Nguyen [Thu, 27 May 2010 15:45:04 +0000 (10:45 -0500)]
mx5: Add i2c to Freescale MX51 Babbage HW
This patch adds I2C functionality to the Freescale MX51 Babbage HW.
The patch adds device structures, i2c board slave device defines,
IOMUX pin defines, and clocks.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Amit Kucheria [Fri, 28 May 2010 08:29:09 +0000 (11:29 +0300)]
arm: mxc: utilise usecount field in clock operations
This patch fixes the clock refcounting when reparenting is used.
Boot-tested on imx51 babbage board.
Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.html
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Wed, 26 May 2010 12:12:11 +0000 (15:12 +0300)]
mx25pdk: add keypad support
The keymap is taken from the Freescale supplied kernel.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Wed, 26 May 2010 12:12:10 +0000 (15:12 +0300)]
mx25: add platform code for imx-keypad
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Mon, 31 May 2010 05:49:40 +0000 (08:49 +0300)]
mxc_nand: add support for platform defined partitions
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer [Tue, 27 Apr 2010 13:24:01 +0000 (15:24 +0200)]
mxc_nand: Fix OOB handling
The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Eric Bénard [Thu, 27 May 2010 08:58:56 +0000 (10:58 +0200)]
eukrea_mbimx27: add audio codec
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:07 +0000 (18:46 +0200)]
eukrea_mbimx27: add support for the keyboard
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:06 +0000 (18:46 +0200)]
MX2X: Add Keypad device definition for MX2X arch
Based on work from Alberto Panizzo for MX3X
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:05 +0000 (18:46 +0200)]
eukrea_mbimx27: use card detect through DAT3 for SDHC1
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:04 +0000 (18:46 +0200)]
mxcmmc: add card detect through DAT3 possibility
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:03 +0000 (18:46 +0200)]
mach-cpuimx27: register wdt and w1_master resources
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:02 +0000 (18:46 +0200)]
mach-cpuimx27: add USB Host2 and OTG support
support copied from mach-pca100.c
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Thu, 20 May 2010 07:22:28 +0000 (09:22 +0200)]
eukrea_mbimx27: fix ADS7846 support
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:00 +0000 (18:46 +0200)]
mach-cpuimx27: fix QuadUART's IRQ typo in pins'setup
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:59 +0000 (18:45 +0200)]
cpuimx27 and mbimx27: allow fine control of UART4 and SDHC2 usage
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:58 +0000 (18:45 +0200)]
eukrea_mbimx27-baseboard: add timings for DVI output
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:57 +0000 (18:45 +0200)]
eukrea_mbimx27-baseboard: add generic-bl and platform-lcd controls
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:56 +0000 (18:45 +0200)]
eukrea_mbimx27-baseboard: fix typo in display name
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wolfram Sang [Fri, 21 May 2010 04:52:06 +0000 (06:52 +0200)]
pcm037/pcm043/pca100: fix ULPI-related build warnings
Like this one (if CONFIG_USB_ULPI is not set):
arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Daniel Mack [Tue, 25 May 2010 14:46:56 +0000 (16:46 +0200)]
ARM: mx3: mx31lilly: pass mc13783 SPI IRQ pin
This makes the resistive touch interface work.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Daniel Mack [Tue, 25 May 2010 14:46:53 +0000 (16:46 +0200)]
ARM: mx3: pcm037: remove unused variable
CC arch/arm/mach-mx3/mach-pcm037.o
arch/arm/mach-mx3/mach-pcm037.c: In function 'mxc_board_init':
arch/arm/mach-mx3/mach-pcm037.c:584: warning: unused variable 'tmp'
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Linus Torvalds [Tue, 25 May 2010 23:59:51 +0000 (16:59 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
drivers/net/usb/asix.c: Fix pointer cast.
be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
proc_dointvec: write a single value
hso: add support for new products
Phonet: fix potential use-after-free in pep_sock_close()
ath9k: remove VEOL support for ad-hoc
ath9k: change beacon allocation to prefer the first beacon slot
sock.h: fix kernel-doc warning
cls_cgroup: Fix build error when built-in
macvlan: do proper cleanup in macvlan_common_newlink() V2
be2net: Bug fix in init code in probe
net/dccp: expansion of error code size
ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
wireless: fix sta_info.h kernel-doc warnings
wireless: fix mac80211.h kernel-doc warnings
iwlwifi: testing the wrong variable in iwl_add_bssid_station()
ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
ath9k_htc: dereferencing before check in hif_usb_tx_cb()
rt2x00: Fix rt2800usb TX descriptor writing.
rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
...
Linus Torvalds [Tue, 25 May 2010 23:53:16 +0000 (16:53 -0700)]
Merge branch 'alpha-next' of git://git./linux/kernel/git/mattst88/alpha-2.6
* 'alpha-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: simplify and optimize sched_find_first_bit
alpha: invoke oom-killer from page fault
Convert alpha to use clocksources instead of arch_gettimeoffset
Linus Torvalds [Tue, 25 May 2010 23:51:55 +0000 (16:51 -0700)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: add devname module aliases to allow module on-demand auto-loading
Linus Torvalds [Tue, 25 May 2010 23:48:30 +0000 (16:48 -0700)]
Revert "module: drop the lock while waiting for module to complete initialization."
This reverts commit
480b02df3aa9f07d1c7df0cd8be7a5ca73893455, since
Rafael reports that it causes occasional kernel paging request faults in
load_module().
Dropping the module lock and re-taking it deep in the call-chain is
definitely not the right thing to do. That just turns the mutex from a
lock into a "random non-locking data structure" that doesn't actually
protect what it's supposed to protect.
Requested-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Brandon Philips <brandon@ifup.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Tue, 25 May 2010 23:24:03 +0000 (16:24 -0700)]
drivers/net/usb/asix.c: Fix pointer cast.
Stephen Rothwell reports the following new warning:
drivers/net/usb/asix.c: In function 'asix_rx_fixup':
drivers/net/usb/asix.c:325: warning: cast from pointer to integer of different size
drivers/net/usb/asix.c:354: warning: cast from pointer to integer of different size
The code just cares about the low alignment bits, so use
an "unsigned long" cast instead of one to "u32".
Signed-off-by: David S. Miller <davem@davemloft.net>
Sarveshwar Bandi [Tue, 25 May 2010 23:16:32 +0000 (16:16 -0700)]
be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
Certain firmware commands/operations to upgrade firmware could take several
seconds to complete. The code presently disables bottom half during these
operations which could lead to unpredictable behaviour in certain cases. This
patch now does all firmware upgrade operations asynchronously using a
completion variable.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
J. R. Okajima [Tue, 25 May 2010 23:10:14 +0000 (16:10 -0700)]
proc_dointvec: write a single value
The commit
00b7c3395aec3df43de5bd02a3c5a099ca51169f
"sysctl: refactor integer handling proc code"
modified the behaviour of writing to /proc.
Before the commit, write("1\n") to /proc/sys/kernel/printk succeeded. But
now it returns EINVAL.
This commit supports writing a single value to a multi-valued entry.
Signed-off-by: J. R. Okajima <hooanon05@yahoo.co.jp>
Reviewed-and-tested-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filip Aben [Tue, 25 May 2010 23:09:23 +0000 (16:09 -0700)]
hso: add support for new products
This patch adds a few new product id's for the hso driver.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Tue, 25 May 2010 23:08:39 +0000 (16:08 -0700)]
Phonet: fix potential use-after-free in pep_sock_close()
sk_common_release() might destroy our last reference to the socket.
So an extra temporary reference is needed during cleanup.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Turner [Thu, 29 Apr 2010 02:49:36 +0000 (22:49 -0400)]
alpha: simplify and optimize sched_find_first_bit
Search only the first 100 bits instead of 140, saving a couple
instructions. The resulting code is about 1/3 faster (40K ticks/1000
iterations down to 30K ticks/1000 iterations).
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Nick Piggin [Thu, 29 Apr 2010 21:48:18 +0000 (17:48 -0400)]
alpha: invoke oom-killer from page fault
As explained in commit
1c0fe6e3bd, we want to call the architecture
independent oom killer when getting an unexplained OOM from
handle_mm_fault, rather than simply killing current.
[mattst88: kill now unused 'survive' label]
Cc: linux-alpha@vger.kernel.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: linux-arch@vger.kernel.org
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
John Stultz [Fri, 19 Mar 2010 16:23:57 +0000 (12:23 -0400)]
Convert alpha to use clocksources instead of arch_gettimeoffset
Alpha has a tsc like rpcc counter that it uses to manage time.
This can be converted to an actual clocksource instead of utilizing
the arch_gettimeoffset method that is really only there for legacy
systems with no continuous counter.
Further cleanups could be made if alpha converted to the clockevent
model.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Richard Henderson <rth@twiddle.net>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Tested-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Kay Sievers [Thu, 20 May 2010 16:07:20 +0000 (18:07 +0200)]
driver core: add devname module aliases to allow module on-demand auto-loading
This adds:
alias: devname:<name>
to some common kernel modules, which will allow the on-demand loading
of the kernel module when the device node is accessed.
Ideally all these modules would be compiled-in, but distros seems too
much in love with their modularization that we need to cover the common
cases with this new facility. It will allow us to remove a bunch of pretty
useless init scripts and modprobes from init scripts.
The static device node aliases will be carried in the module itself. The
program depmod will extract this information to a file in the module directory:
$ cat /lib/modules/
2.6.34-00650-g537b60d-dirty/modules.devname
# Device nodes to trigger on-demand module loading.
microcode cpu/microcode c10:184
fuse fuse c10:229
ppp_generic ppp c108:0
tun net/tun c10:200
dm_mod mapper/control c10:235
Udev will pick up the depmod created file on startup and create all the
static device nodes which the kernel modules specify, so that these modules
get automatically loaded when the device node is accessed:
$ /sbin/udevd --debug
...
static_dev_create_from_modules: mknod '/dev/cpu/microcode' c10:184
static_dev_create_from_modules: mknod '/dev/fuse' c10:229
static_dev_create_from_modules: mknod '/dev/ppp' c108:0
static_dev_create_from_modules: mknod '/dev/net/tun' c10:200
static_dev_create_from_modules: mknod '/dev/mapper/control' c10:235
udev_rules_apply_static_dev_perms: chmod '/dev/net/tun' 0666
udev_rules_apply_static_dev_perms: chmod '/dev/fuse' 0666
A few device nodes are switched to statically allocated numbers, to allow
the static nodes to work. This might also useful for systems which still run
a plain static /dev, which is completely unsafe to use with any dynamic minor
numbers.
Note:
The devname aliases must be limited to the *common* and *single*instance*
device nodes, like the misc devices, and never be used for conceptually limited
systems like the loop devices, which should rather get fixed properly and get a
control node for losetup to talk to, instead of creating a random number of
device nodes in advance, regardless if they are ever used.
This facility is to hide the mess distros are creating with too modualized
kernels, and just to hide that these modules are not compiled-in, and not to
paper-over broken concepts. Thanks! :)
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Ian Kent <raven@themaw.net>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David S. Miller [Tue, 25 May 2010 21:05:24 +0000 (14:05 -0700)]
Merge branch 'wimax-2.6.35.y' of git://git./linux/kernel/git/inaky/wimax
David S. Miller [Tue, 25 May 2010 20:15:11 +0000 (13:15 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Linus Torvalds [Tue, 25 May 2010 19:06:33 +0000 (12:06 -0700)]
Merge branch 'devel' of /home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (103 commits)
ARM: 6141/1: Add audio support part in arch/arm/mach-w90x900
ARM: 5939/1: ARM: Add option CMDLINE_FORCE to force usage of the in-kernel cmdline
ARM: 6140/1: silence a bogus sparse warning in unwind.c
ARM: mach-at91: duplicated include
ARM: arch/arm/nwfpe/fpsr.h: Checkpatch cleanup
ARM: arch/arm/mach-shark/pci.c: Checkpatch cleanup
ARM: arch/arm/nwfpe/ChangeLog: Checkpatch cleanup
ARM: arch/arm/mach-sa1100/leds.c: Checkpatch cleanup
ARM: arch/arm/mach-h720x/common.h: Checkpatch cleanup
ARM: arch/arm/mach-footbridge/ebsa285-pci.c: Checkpatch cleanup
ARM: arch/arm/mach-clps711x/Makefile.boot: Checkpatch cleanup
ARM: arch/arm/boot/bootp/bootp.lds: Checkpatch cleanup
ARM: SPEAR6xx: remove duplicated #include
ARM: s3c6400_defconfig: Add NAND driver
ARM: s3c6400_defconfig: enable sound as modules
ARM: s3c6400_defconfig: enable power management
ARM: s5pv210_defconfig: Update s5pv210_defconfig to v2.6.34
ARM: s5pc110_defconfig: Update s5pc110_defconfig to v2.6.34
ARM: s5p6442_defconfig: Update s5p6442_defconfig to v2.6.34
ARM: s5p6440_defconfig: Update s5p6440_defconfig to v2.6.34
...
Linus Torvalds [Tue, 25 May 2010 19:05:17 +0000 (12:05 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix incorrect unlock in nes_process_mac_intr()
RDMA/nes: Async event for closed QP causes crash
RDMA/nes: Have ethtool read hardware registers for rx/tx stats
RDMA/cxgb4: Only insert sq qid in lookup table
RDMA/cxgb4: Support IB_WR_READ_WITH_INV opcode
RDMA/cxgb4: Set fence flag for inv-local-stag work requests
RDMA/cxgb4: Update some HW limits
RDMA/cxgb4: Don't limit fastreg page list depth
RDMA/cxgb4: Return proper errors in fastreg mr/pbl allocation
RDMA/cxgb4: Fix overflow bug in CQ arm
RDMA/cxgb4: Optimize CQ overflow detection
RDMA/cxgb4: CQ size must be IQ size - 2
RDMA/cxgb4: Register RDMA provider based on LLD state_change events
RDMA/cxgb4: Detach from the LLD after unregistering RDMA device
IB/ipath: Remove support for QLogic PCIe QLE devices
IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters
IB/mad: Make needlessly global mad_sendq_size/mad_recvq_size static
IB/core: Allow device-specific per-port sysfs files
mlx4_core: Clean up mlx4_alloc_icm() a bit
mlx4_core: Fix possible chunk sg list overflow in mlx4_alloc_icm()
Linus Torvalds [Tue, 25 May 2010 19:04:17 +0000 (12:04 -0700)]
Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/xilinx: Fix compile error
spi/davinci: Fix clock prescale factor computation
spi: move bitbang txrx utility functions to private header
spi/mpc5121: Add SPI master driver for MPC5121 PSC
powerpc/mpc5121: move PSC FIFO memory init to platform code
spi/ep93xx: implemented driver for Cirrus EP93xx SPI controller
Documentation/spi/* compile warning fix
spi/omap2_mcspi: Check params before dereference or use
spi/omap2_mcspi: add turbo mode support
spi/omap2_mcspi: change default DMA_MIN_BYTES value to 160
spi/pl022: fix stop queue procedure
spi/pl022: add support for the PL023 derivate
spi/pl022: fix up differences between ARM and ST versions
spi/spi_mpc8xxx: Do not use map_tx_dma to unmap rx_dma
spi/spi_mpc8xxx: Fix QE mode Litte Endian
spi/spi_mpc8xxx: fix potential memory corruption.
Linus Torvalds [Tue, 25 May 2010 19:03:17 +0000 (12:03 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
arch/m68knommu/platform/68360/commproc.c: Checkpatch cleanup
arch/m68knommu/mm/fault.c: Checkpatch cleanup
m68knommu: improve short help of m68knommu/Kconfig/RAMSIZE for '0' case
m68knommu: remove un-used mcfsmc.h
m68knommu: add smc91x support for ColdFire NETtel boards
m68knommu: add smc91x support to ColdFire 5249 platform
m68knommu: remove size limit on non-MMU TASK_SIZE
m68knommu: fix broken use of BUAD_TABLE_SIZE in 68328serial driver
m68knommu: Coldfire QSPI platform support
Linus Torvalds [Tue, 25 May 2010 18:49:41 +0000 (11:49 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: return set_mode is same mode is requested
Regulators: ab3100/bq24022: add a missing .owner field in regulator_desc
twl6030: regulator: Remove vsel tables and use formula for calculation
mc13783-regulator: fix vaild voltage range checking for mc13783_fixed_regulator_set_voltage
regulator: use voltage number array in 88pm860x
regulator: make 88pm860x sharing one driver structure
regulator: simplify regulator_register() error handling
regulator: fix unset_regulator_supplies() to remove all matches
regulator: prevent registration of matching regulator consumer supplies
regulator: Allow regulator-regulator supplies to be specified by name
Linus Torvalds [Tue, 25 May 2010 18:40:40 +0000 (11:40 -0700)]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: Driver for the watchdog timer on Freescale IMX2 (and later) processors.
watchdog: s3c2410_wdt - Fix on handling of the request_mem_region fail
watchdog: s3c2410_wdt - Add extra option to include watchdog for Samsung SoCs
iTCO_wdt: fix TCO V1 timeout values and limits
watchdog: twl4030_wdt: Disable watchdog during probing
watchdog: update/improve/consolidate watchdog driver
watchdog: booke_wdt: fix ioctl status flags
watchdog: fix several MODULE_PARM_DESC strings
watchdog: bfin: use new common Blackfin watchdog header
Roland Dreier [Tue, 25 May 2010 16:54:03 +0000 (09:54 -0700)]
Merge branches 'cxgb4', 'misc', 'mlx4', 'nes' and 'qib' into for-next
Chien Tung [Tue, 25 May 2010 15:13:09 +0000 (10:13 -0500)]
RDMA/nes: Fix incorrect unlock in nes_process_mac_intr()
Commit
ce6e74f2 ("RDMA/nes: Make nesadapter->phy_lock usage
consistent") introduced a problem where phy_lock was only unlocked
within an if statement and so nes_process_mac_intr() could return with
phy_lock still held. Fix this.
This was discovered because of the sparse warning:
drivers/infiniband/hw/nes/nes_hw.c:2643:9: warning: context imbalance in 'nes_process_mac_intr' - different lock contexts for basic block
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Linus Torvalds [Tue, 25 May 2010 15:17:51 +0000 (08:17 -0700)]
Merge git://git./linux/kernel/git/steve/gfs2-2.6-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Fix permissions checking for setflags ioctl()
GFS2: Don't "get" xattrs for ACLs when ACLs are turned off
GFS2: Rework reclaiming unlinked dinodes
Linus Torvalds [Tue, 25 May 2010 15:17:01 +0000 (08:17 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: Ensure inode allocation buffers are fully replayed
xfs: enable background pushing of the CIL
xfs: forced unmounts need to push the CIL
xfs: Introduce delayed logging core code
xfs: Delayed logging design documentation
xfs: Improve scalability of busy extent tracking
xfs: make the log ticket ID available outside the log infrastructure
xfs: clean up log ticket overrun debug output
xfs: Clean up XFS_BLI_* flag namespace
xfs: modify buffer item reference counting
xfs: allow log ticket allocation to take allocation flags
xfs: Don't reuse the same transaction ID for duplicated transactions.
Linus Torvalds [Tue, 25 May 2010 15:16:34 +0000 (08:16 -0700)]
Merge git://git.infradead.org/battery-2.6
* git://git.infradead.org/battery-2.6:
power_supply: Fix regression for 'type' property
Felix Fietkau [Thu, 13 May 2010 18:37:25 +0000 (20:37 +0200)]
ath9k: remove VEOL support for ad-hoc
With VEOL, Beacon transmission in ad-hoc does not currently work.
I believe for larger ad-hoc networks, VEOL is too unreliable, as
it can get beacon transmissions stuck during synchronization.
Use SWBA based beacon trasmission similar to AP mode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 13 May 2010 18:37:24 +0000 (20:37 +0200)]
ath9k: change beacon allocation to prefer the first beacon slot
This fixes IBSS beacon transmissions without VEOL enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Henrik Kretzschmar [Mon, 24 May 2010 21:34:09 +0000 (14:34 -0700)]
auxdisplay: section cleanup in cfag12864bfb driver
This fixes a two section mismatches and makes remove() __devexit.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Mon, 24 May 2010 21:34:09 +0000 (14:34 -0700)]
nuc900fb: release correct mem region
We should be releasing "res->start" here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Wang Qiang <rurality.linux@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Albert Herranz [Mon, 24 May 2010 21:34:08 +0000 (14:34 -0700)]
fb_defio: fix for non-dirty ptes
Fix a problem observed while using fb_defio with a short delay on a
PowerPC platform.
It is possible that page_mkclean() is invoked in the deferred io work
function _before_ a PTE has been marked dirty. In this case, the page is
removed from the defio pagelist but page_mkclean() does not write-protect
the page again. The end result is that defio ignores all subsequent
writes to the page and the corresponding portions of the framebuffer never
get updated.
The fix consists in keeping track of the pages with non-dirty PTEs,
re-checking them again on the next deferred io work iteration. Note that
those pages are not passed to the defio callback as they are not written
by userspace yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:34:07 +0000 (14:34 -0700)]
sgivwfb: fix sections
Since the drivers probe call was changed from .init.text to .devinit.text
in commit
c2e13037e6794bd0d9de3f9ecabf5615f15c160b ("platform-drivers:
move probe to .devinit.text in drivers/video") the fb_fix_screeninfo and
fb_var_screeninfo structures must be changed from .init.data to
.devinit.data, too.
Also the drivers remove routine should be moved from .text to .devexit.text
It removes these 7 section mismatch warnings from modpost:
WARNING: vmlinux.o(.devinit.text+0x1e28): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_fix
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_fix.
If sgivwfb_fix is only used by sgivwfb_probe then
annotate sgivwfb_fix with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e50): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e59): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e60): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_fix
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_fix.
If sgivwfb_fix is only used by sgivwfb_probe then
annotate sgivwfb_fix with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e6a): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e7f): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_var1600sw
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_var1600sw.
If sgivwfb_var1600sw is only used by sgivwfb_probe then
annotate sgivwfb_var1600sw with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e91): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_var
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_var.
If sgivwfb_var is only used by sgivwfb_probe then
annotate sgivwfb_var with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:34:05 +0000 (14:34 -0700)]
s3c2410fb: fix sections
Since the drivers probe calls were changed from .init.text to
.devinit.text in commit
c2e13037e6794bd0d9de3f9ecabf5615f15c160b
("platform-drivers: move probe to .devinit.text in drivers/video") all the
function from .init.text should be moved to .devinit.text, too.
The drivers remove calls can also be move from .text to .devexit.text.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:34:04 +0000 (14:34 -0700)]
hitfb: fix sections
Since the drivers probe call was changed from .init.text to .devinit.text
in commit
c2e13037e6794bd0d9de3f9ecabf5615f15c160b ("platform-drivers:
move probe to .devinit.text in drivers/video") the fb_fix_screeninfo and
fb_var_screeninfo structures must be changed from .init.data to
.devinit.data, too.
Also the drivers remove routine should be moved from .exit.text to
.devexit.text
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grazvydas Ignotas [Mon, 24 May 2010 21:34:02 +0000 (14:34 -0700)]
fbdev: move FBIO_WAITFORVSYNC to linux/fb.h
FBIO_WAITFORVSYNC is currently implemented by matroxfb, atyfb, intelfb and
more. All of them keep redefining the same FBIO_WAITFORVSYNC macro over
and over again, so move it to linux/fb.h and clean up those duplicate
defines.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Maik Broemme <mbroemme@plusserver.de>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Martin Ambrose [Mon, 24 May 2010 21:34:01 +0000 (14:34 -0700)]
fbdev: da8xx/omap-l1xx: implement double buffering
This work includes the following:
- Implement handler for FBIO_WAITFORVSYNC ioctl.
- Allocate the data and palette buffers separately. A consequence of
this is that the palette and data loading is now done in different
phases. And that the LCD must be disabled temporarily after the palette
is loaded but this will only happen once after init and each time the
palette is changed. I think this is OK.
- Allocate two (ping and pong) framebuffers from memory.
- Add pan_display handler which toggles the LCDC DMA registers between
the ping and pong buffers.
Signed-off-by: Martin Ambrose <martin@ti.com>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:34:00 +0000 (14:34 -0700)]
fbdev: section cleanup in w100fb
Fix up the section in the w100fb driver, by moving:
* w100fb_remove() from .text to .devexit.text
* w100_get_xtal_table() from .text to .devinit.text
* w100fb_init() from .devinit.text to .init.text
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:33:59 +0000 (14:33 -0700)]
fbdev: section cleanup in vga16fb
Fix up the sections in the vga16fb driver, by moving:
* the variables vga16_defined and vga16fb
from .init.data to .devinit.data
* vga16fb_setup() from .text to .init.text
* vga16fb_remove() from .text. to .devexit.text
This fixes the following warnings issued by modpost:
WARNING: drivers/video/built-in.o(.devinit.text+0x1a420): Section mismatch in re
ference from the function vga16fb_probe() to the (unknown reference) .init.data:
(unknown)
The function __devinit vga16fb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by vga16fb_probe then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x1a437): Section mismatch in reference from the function vga16fb_probe() to the variable .init.data:vga16fb_defined
The function __devinit vga16fb_probe() references
a variable __initdata vga16fb_defined.
If vga16fb_defined is only used by vga16fb_probe then
annotate vga16fb_defined with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x1a457): Section mismatch in reference from the function vga16fb_probe() to the variable .init.data:vga16fb_fix
The function __devinit vga16fb_probe() references
a variable __initdata vga16fb_fix.
If vga16fb_fix is only used by vga16fb_probe then
annotate vga16fb_fix with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:33:57 +0000 (14:33 -0700)]
fbdev: section cleanup in vfb
Fix up the section in the vfb driver, by moving the variables vfb_default
and vfb_fix from .init.data to .devinit.data
This fixes the following warnings issued by modpost:
WARNING: drivers/video/vfb.o(.devinit.text+0xf8): Section mismatch in reference from the function vfb_probe() to the variable .init.data:vfb_default
The function __devinit vfb_probe() references
a variable __initdata vfb_default.
If vfb_default is only used by vfb_probe then
annotate vfb_default with a matching annotation.
WARNING: drivers/video/vfb.o(.devinit.text+0x114): Section mismatch in reference from the function vfb_probe() to the variable .init.data:vfb_fix
The function __devinit vfb_probe() references
a variable __initdata vfb_fix.
If vfb_fix is only used by vfb_probe then
annotate vfb_fix with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:33:56 +0000 (14:33 -0700)]
fbdev: section cleanup in hgafb
Fix up the sections in the hgafb driver, by
* moving hga_default_var and hga_fix from .init.data to .devinit.data
* moving hga_detect() from .init.text to .devinit.text
* moving hga_fb_remove() from .text to .devexit.text
This fixes the following warnings issued by modpost:
WARNING: drivers/video/hgafb.o(.devinit.text+0x18): Section mismatch in referenc
e from the function hgafb_probe() to the function .init.text:hga_card_detect()
The function __devinit hgafb_probe() references
a function __init hga_card_detect().
If hga_card_detect is only used by hgafb_probe then
annotate hga_card_detect with a matching annotation.
WARNING: drivers/video/hgafb.o(.devinit.text+0xfe): Section mismatch in referenc
e from the function hgafb_probe() to the variable .init.data:hga_fix
The function __devinit hgafb_probe() references
a variable __initdata hga_fix.
If hga_fix is only used by hgafb_probe then
annotate hga_fix with a matching annotation.
WARNING: drivers/video/hgafb.o(.devinit.text+0x105): Section mismatch in reference from the function hgafb_probe() to the variable .init.data:hga_default_var
The function __devinit hgafb_probe() references
a variable __initdata hga_default_var.
If hga_default_var is only used by hgafb_probe then
annotate hga_default_var with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Kretzschmar [Mon, 24 May 2010 21:33:54 +0000 (14:33 -0700)]
fbdev: section cleanup in arcfb
Fix the sections in the arcfb driver, by moving:
* the variables arcfb_fix and arcfb_var from .init.data to .devinit.data
* arcfb_remove() from .text to .devexit.text
This fixes the following warnings issued by modpost:
WARNING: drivers/video/built-in.o(.devinit.text+0x543): Section mismatch in reference from the function arcfb_probe() to the variable .init.data:arcfb_var
The function __devinit arcfb_probe() references
a variable __initdata arcfb_var.
If arcfb_var is only used by arcfb_probe then
annotate arcfb_var with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x558): Section mismatch in reference from the function arcfb_probe() to the variable .init.data:arcfb_fix
The function __devinit arcfb_probe() references
a variable __initdata arcfb_fix.
If arcfb_fix is only used by arcfb_probe then
annotate arcfb_fix with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Mon, 24 May 2010 21:33:53 +0000 (14:33 -0700)]
sis: strcpy() => strlcpy()
These are different size buffers (40 chars vs 16), we may as well be
cautious.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Hennerich [Mon, 24 May 2010 21:33:52 +0000 (14:33 -0700)]
fbdev: bfin-lq035q1-fb: respect new PPI mode platform field
This lets us support the new BF527-EZKIT V2.1 via platform resources
tweaks only.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown [Mon, 24 May 2010 21:33:51 +0000 (14:33 -0700)]
rtc: use genirq directly in rtc-wm831x
Now that the WM831x core uses genirq for the IRQ controller there is no
need to use the WM831x-specific wrappers to request interrupts so convert
to use genirq directly.
Also use more meaningful strings to make /proc/interrupts more readily
legible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Mon, 24 May 2010 21:33:49 +0000 (14:33 -0700)]
rtc-cmos: do dev_set_drvdata() earlier in the initialization
The bug is an oops when dev_get_drvdata() returned null in
cmos_update_irq_enable(). The call tree looks like this:
rtc_dev_ioctl()
=> rtc_update_irq_enable()
=> cmos_update_irq_enable()
It's caused by a race condition in the module initialization. It is
rtc_device_register() which makes the ioctl operations live so I moved
the call to dev_set_drvdata() before the call to rtc_device_register().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15963
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Malte Schroder <maltesch@gmx.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marc Zyngier [Mon, 24 May 2010 21:33:47 +0000 (14:33 -0700)]
rtc-ds1302: add some abstraction for new platform support
The current ds1302 driver (or at least the one that lives in /drivers/rtc)
seems to be designed for memory mapped devices only. This make it quite
hard to add support for GPIO-based implementations (as this is the case
for the upcoming Arcom Vulcan).
This patch moves the direct register access to inline functions with
explicit names. Still not as good as a proper platform driver, but at
least neater.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H Hartley Sweeten [Mon, 24 May 2010 21:33:46 +0000 (14:33 -0700)]
rtc-isl1208: use sysfs_{create/remove}_group
Instead of individually creating and removing the sysfs device attribute
files, wrap them in an attribute_group and use
sysfs_{create/remove}_group.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vladimir Zapolskiy [Mon, 24 May 2010 21:33:46 +0000 (14:33 -0700)]
rtc-mxc: remove unnecessary clock source for rtc subsystem
On imx SoCs rtc clock parent is CKIL, but clock rate shall be determined
using rtc clock itself, that eliminates CKIL clock usage in the driver.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maurus Cuelenaere [Mon, 24 May 2010 21:33:43 +0000 (14:33 -0700)]
s3c rtc driver: add support for S3C64xx
Add support for the S3C64xx SoC to the generic S3C RTC driver.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Weiyi [Mon, 24 May 2010 21:33:43 +0000 (14:33 -0700)]
smbfs: remove duplicated #include
Remove duplicated #include('s) in fs/smbfs/symlink.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Mon, 24 May 2010 21:33:41 +0000 (14:33 -0700)]
xen: fix build when SYSRQ is disabled
Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:
drivers/xen/manage.c:223: error: implicit declaration of function 'handle_sysrq'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / log