Reiter Wolfgang [Sat, 31 Dec 2016 20:11:57 +0000 (21:11 +0100)]
drop_monitor: add missing call to genlmsg_end
Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stafford Horne [Wed, 14 Dec 2016 12:27:57 +0000 (21:27 +0900)]
openrisc: Add _text symbol to fix ksym build error
The build robot reports:
.tmp_kallsyms1.o: In function `kallsyms_relative_base':
>> (.rodata+0x8a18): undefined reference to `_text'
This is when using 'make alldefconfig'. Adding this _text symbol to mark
the start of the kernel as in other architecture fixes this.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
Linus Torvalds [Sun, 1 Jan 2017 22:31:53 +0000 (14:31 -0800)]
Linux 4.10-rc2
Linus Torvalds [Sun, 1 Jan 2017 20:27:05 +0000 (12:27 -0800)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull DAX updates from Dan Williams:
"The completion of Jan's DAX work for 4.10.
As I mentioned in the libnvdimm-for-4.10 pull request, these are some
final fixes for the DAX dirty-cacheline-tracking invalidation work
that was merged through the -mm, ext4, and xfs trees in -rc1. These
patches were prepared prior to the merge window, but we waited for
4.10-rc1 to have a stable merge base after all the prerequisites were
merged.
Quoting Jan on the overall changes in these patches:
"So I'd like all these 6 patches to go for rc2. The first three
patches fix invalidation of exceptional DAX entries (a bug which
is there for a long time) - without these patches data loss can
occur on power failure even though user called fsync(2). The other
three patches change locking of DAX faults so that ->iomap_begin()
is called in a more relaxed locking context and we are safe to
start a transaction there for ext4"
These have received a build success notification from the kbuild
robot, and pass the latest libnvdimm unit tests. There have not been
any -next releases since -rc1, so they have not appeared there"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
ext4: Simplify DAX fault path
dax: Call ->iomap_begin without entry lock during dax fault
dax: Finish fault completely when loading holes
dax: Avoid page invalidation races and unnecessary radix tree traversals
mm: Invalidate DAX radix tree entries only if appropriate
ext2: Return BH_New buffers for zeroed blocks
Eric Biggers [Fri, 30 Dec 2016 23:42:32 +0000 (17:42 -0600)]
net: socket: don't set sk_uid to garbage value in ->setattr()
->setattr() was recently implemented for socket files to sync the socket
inode's uid to the new 'sk_uid' member of struct sock. It does this by
copying over the ia_uid member of struct iattr. However, ia_uid is
actually only valid when ATTR_UID is set in ia_valid, indicating that
the uid is being changed, e.g. by chown. Other metadata operations such
as chmod or utimes leave ia_uid uninitialized. Therefore, sk_uid could
be set to a "garbage" value from the stack.
Fix this by only copying the uid over when ATTR_UID is set.
Fixes:
86741ec25462 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Mon, 19 Dec 2016 22:20:13 +0000 (14:20 -0800)]
fscrypt: fix renaming and linking special files
Attempting to link a device node, named pipe, or socket file into an
encrypted directory through rename(2) or link(2) always failed with
EPERM. This happened because fscrypt_has_permitted_context() saw that
the file was unencrypted and forbid creating the link. This behavior
was unexpected because such files are never encrypted; only regular
files, directories, and symlinks can be encrypted.
To fix this, make fscrypt_has_permitted_context() always return true on
special files.
This will be covered by a test in my encryption xfstests patchset.
Fixes:
9bd8212f981e ("ext4 crypto: add encryption policy and password salt support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Kishon Vijay Abraham I [Fri, 30 Dec 2016 08:07:20 +0000 (13:37 +0530)]
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
Add 'gpios' property to pcie1 dt node and populate it with
GPIO3_23 in order to drive PCIE_RESETn high.
This gets PCIe cards to be detected in AM572X IDK board.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Fri, 30 Dec 2016 17:32:26 +0000 (09:32 -0800)]
Merge tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Two small fixes:
- A merge error on my part broke the DocBook build. I've
requisitioned one of tglx's frozen sharks for appropriate
disciplinary action and resolved to be more careful about testing
the DocBook stuff as long as it's still around.
- Fix an error in unaligned-memory-access.txt"
* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
docs: Fix build failure
Linus Torvalds [Fri, 30 Dec 2016 17:29:50 +0000 (09:29 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a boot failure on some platforms when crypto self test is
enabled along with the new acomp interface"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - Use heap buffer for acomp test input
Sudeep Holla [Tue, 13 Dec 2016 14:24:53 +0000 (14:24 +0000)]
arm64: dts: vexpress: Support GICC_DIR operations
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation. This patch is based on similar one from Christoffer Dall:
commit
368400e242dc ("ARM: dts: vexpress: Support GICC_DIR operations")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Christoffer Dall [Sat, 10 Dec 2016 20:13:51 +0000 (21:13 +0100)]
ARM: dts: vexpress: Support GICC_DIR operations
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[sudeep.holla@arm.com: included same fix for tc1 platform too]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Martin Blumenstingl [Sun, 11 Dec 2016 21:14:32 +0000 (22:14 +0100)]
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
The pre-1.0 SCPI firmwares are using single __le32 as sensor value,
while the SCPI v1.0 protocol uses two __le32 as sensor values(64bit)
split into 32bit upper and 32bit lower value.
Using an "struct sensor_value" to read the sensor value on a pre-1.0
SCPI firmware gives garbage in the "hi_val" field.
This patch fixes the issue by reading only the lower 32-bit value for
all pre-1.0 SCPI versions.
Suggested-by: Sudeep Holla <Sudeep.Holla@arm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[sudeep.holla@arm.com: updated the commit log to reflect the implementation]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Chanwoo Choi [Fri, 30 Dec 2016 04:14:18 +0000 (13:14 +0900)]
pinctrl: samsung: Fix the width of PINCFG_TYPE_DRV bitfields for Exynos5433
This patch fixes the wrong width of PINCFG_TYPE_DRV bitfields for Exynos5433
because PINCFG_TYPE_DRV of Exynos5433 has 4bit fields in the *_DRV
registers. Usually, other Exynos have 2bit field for PINCFG_TYPE_DRV.
Fixes:
3c5ecc9ed353 ("pinctrl: exynos: Add support for Exynos5433")
Cc: stable@vger.kernel.org
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
David Ahern [Thu, 29 Dec 2016 23:29:03 +0000 (15:29 -0800)]
net: ipv4: dst for local input routes should use l3mdev if relevant
IPv4 output routes already use l3mdev device instead of loopback for dst's
if it is applicable. Change local input routes to do the same.
This fixes icmp responses for unreachable UDP ports which are directed
to the wrong table after commit
9d1a6c4ea43e4 because local_input
routes use the loopback device. Moving from ingress device to loopback
loses the L3 domain causing responses based on the dst to get to lost.
Fixes:
9d1a6c4ea43e4 ("net: icmp_route_lookup should use rt dev to
determine L3 domain")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Thu, 29 Dec 2016 21:07:38 +0000 (00:07 +0300)]
sh_eth: fix branch prediction in sh_eth_interrupt()
IIUC, likely()/unlikely() should apply to the whole *if* statement's
expression, not a part of it -- fix such expression in sh_eth_interrupt()
accordingly...
Fixes:
283e38db65e7 ("sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Thu, 29 Dec 2016 22:16:07 +0000 (14:16 -0800)]
mm/filemap: fix parameters to test_bit()
mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
return test_bit(PG_waiters);
^~~~~~~~
Fixes:
b91e1302ad9b ('mm: optimize PageWaiters bit use for unlock_page()')
Signed-off-by: Olof Johansson <olof@lixom.net>
Brown-paper-bag-by: Linus Torvalds <dummy@duh.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helge Deller [Tue, 27 Dec 2016 17:03:50 +0000 (18:03 +0100)]
parisc: Drop TIF_RESTORE_SIGMASK and switch to generic code
Commit
7e7814180b33 ("signal: consolidate {TS,TLF}_RESTORE_SIGMASK code")
introduced code with which the "restore sigmask" flag lives in task_struct
instead of ti->flags. Let's use this optimization on parisc too.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Mon, 26 Dec 2016 11:46:01 +0000 (12:46 +0100)]
parisc: Mark cr16 clocksource unstable on SMP systems
The cr16 interval timer of each CPU is not syncronized to other cr16
timers in other CPUs in a SMP system. So, delay the registration of the
cr16 clocksource until all CPUs have been detected and then - if we are
on a SMP machine - mark the cr16 clocksource as unstable and lower it's
rating before registering it at the clocksource framework.
This patch fixes the stalled CPU warnings which we have seen since
introduction of the cr16 clocksource.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.8+
Neil Armstrong [Tue, 6 Dec 2016 14:08:16 +0000 (15:08 +0100)]
pinctrl: meson: fix gpio request disabling other modes
The pinctrl_gpio_request is called with the "full" gpio number, already
containing the base, then meson_pmx_request_gpio is then called with the
final pin number.
Remove the base addition when calling meson_pmx_disable_other_groups.
Fixes:
6ac730951104 ("pinctrl: add driver for Amlogic Meson SoCs")
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Shyam Sundar S K [Thu, 8 Dec 2016 12:01:14 +0000 (17:31 +0530)]
pinctrl/amd: Set the level based on ACPI tables
In the function amd_gpio_irq_set_type, read the values from
the ACPI table to set the level and drop the settings passed
by the client.
Cc: <stable@vger.kernel.org> # 4.8.x+
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Reviewed-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
David S. Miller [Thu, 29 Dec 2016 19:17:42 +0000 (14:17 -0500)]
Merge branch 'mlx4-misc-fixes'
Tariq Toukan says:
====================
mlx4 misc fixes
This patchset contains several bug fixes from the team to the
mlx4 Eth and Core drivers.
Series generated against net commit:
60133867f1f1 'net: wan: slic_ds26522: fix spelling mistake: "configurated" -> "configured"'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 29 Dec 2016 16:37:13 +0000 (18:37 +0200)]
net/mlx4_core: Fix raw qp flow steering rules under SRIOV
Demoting simple flow steering rule priority (for DPDK) was achieved by
wrapping FW commands MLX4_QP_FLOW_STEERING_ATTACH/DETACH for the PF
as well, and forcing the priority to MLX4_DOMAIN_NIC in the wrapper
function for the PF and all VFs.
In function mlx4_ib_create_flow(), this change caused the main rule
creation for the PF to be wrapped, while it left the associated
tunnel steering rule creation unwrapped for the PF.
This mismatch caused rule deletion failures in mlx4_ib_destroy_flow()
for the PF when the detach wrapper function did not find the associated
tunnel-steering rule (since creation of that rule for the PF did not
go through the wrapper function).
Fix this by setting MLX4_QP_FLOW_STEERING_ATTACH/DETACH to be "native"
(so that the PF invocation does not go through the wrapper), and perform
the required priority demotion for the PF in the mlx4_ib_create_flow()
code path.
Fixes:
48564135cba8 ("net/mlx4_core: Demote simple multicast and broadcast flow steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slava Shwartsman [Thu, 29 Dec 2016 16:37:12 +0000 (18:37 +0200)]
net/mlx4_en: Fix type mismatch for 32-bit systems
is_power_of_2 expects unsigned long and we pass u64 max_val_cycles,
this will be truncated on 32 bit systems, and the result is not what we
were expecting.
div_u64 expects u32 as a second argument and we pass
max_val_cycles_rounded which is u64 hence it will always be truncated.
Fix was tested on both 64 and 32 bit systems and got same results for
max_val_cycles and max_val_cycles_rounded.
Fixes:
4850cf458157 ("net/mlx4_en: Resolve dividing by zero in 32-bit system")
Signed-off-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Thu, 29 Dec 2016 16:37:11 +0000 (18:37 +0200)]
net/mlx4: Remove BUG_ON from ICM allocation routine
This patch removes BUG_ON() macro from mlx4_alloc_icm_coherent()
by checking DMA address alignment in advance and performing proper
folding in case of error.
Fixes:
5b0bf5e25efe ("mlx4_core: Support ICM tables in coherent memory")
Reported-by: Ozgur Karatas <okaratas@member.fsf.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugenia Emantayev [Thu, 29 Dec 2016 16:37:10 +0000 (18:37 +0200)]
net/mlx4_en: Fix bad WQE issue
Single send WQE in RX buffer should be stamped with software
ownership in order to prevent the flow of QP in error in FW
once UPDATE_QP is called.
Fixes:
9f519f68cfff ('mlx4_en: Not using Shared Receive Queues')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 29 Dec 2016 16:37:09 +0000 (18:37 +0200)]
net/mlx4_core: Use-after-free causes a resource leak in flow-steering detach
mlx4_QP_FLOW_STEERING_DETACH_wrapper first removes the steering
rule (which results in freeing the rule structure), and then
references a field in this struct (the qp number) when releasing the
busy-status on the rule's qp.
Since this memory was freed, it could reallocated and changed.
Therefore, the qp number in the struct may be incorrect,
so that we are releasing the incorrect qp. This leaves the rule's qp
in the busy state (and could possibly release an incorrect qp as well).
Fix this by saving the qp number in a local variable, for use after
removing the steering rule.
Fixes:
2c473ae7e582 ("net/mlx4_core: Disallow releasing VF QPs which have steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Zhang [Thu, 29 Dec 2016 08:45:04 +0000 (16:45 +0800)]
net: fix incorrect original ingress device index in PKTINFO
When we send a packet for our own local address on a non-loopback
interface (e.g. eth0), due to the change had been introduced from
commit
0b922b7a829c ("net: original ingress device index in PKTINFO"), the
original ingress device index would be set as the loopback interface.
However, the packet should be considered as if it is being arrived via the
sending interface (eth0), otherwise it would break the expectation of the
userspace application (e.g. the DHCPRELEASE message from dhcp_release
binary would be ignored by the dnsmasq daemon, since it come from lo which
is not the interface dnsmasq bind to)
Fixes:
0b922b7a829c ("net: original ingress device index in PKTINFO")
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Wei Zhang <asuka.com@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mathias Krause [Wed, 28 Dec 2016 16:52:15 +0000 (17:52 +0100)]
rtnl: stats - add missing netlink message size checks
We miss to check if the netlink message is actually big enough to contain
a struct if_stats_msg.
Add a check to prevent userland from sending us short messages that would
make us access memory beyond the end of the message.
Fixes:
10c9ead9f3c6 ("rtnetlink: add new RTM_GETSTATS message to dump...")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 27 Dec 2016 19:40:38 +0000 (11:40 -0800)]
mm: optimize PageWaiters bit use for unlock_page()
In commit
62906027091f ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.
However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.
On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd. The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.
On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result. However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.
So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too. And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.
This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.
The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit. Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.
So this introduces the new architecture primitive
clear_bit_unlock_is_negative_byte();
and adds the trivial implementation for x86. We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better. According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.
All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test". After this, it's down to
0.66%, so just a quarter of the cost it used to be.
(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Wed, 28 Dec 2016 23:44:41 +0000 (15:44 -0800)]
net: stmmac: Fix error path after register_netdev move
Commit
5701659004d6 ("net: stmmac: Fix race between stmmac_drv_probe and
stmmac_open") re-ordered how the MDIO bus registration and the network
device are registered, but missed to unwind the MDIO bus registration in
case we fail to register the network device.
Fixes:
5701659004d6 ("net: stmmac: Fix race between stmmac_drv_probe and stmmac_open")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng Li [Wed, 28 Dec 2016 15:23:46 +0000 (23:23 +0800)]
ipv6: Should use consistent conditional judgement for ip6 fragment between __ip6_append_data and ip6_finish_output
There is an inconsistent conditional judgement between __ip6_append_data
and ip6_finish_output functions, the variable length in __ip6_append_data
just include the length of application's payload and udp6 header, don't
include the length of ipv6 header, but in ip6_finish_output use
(skb->len > ip6_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ipv6 header.
That causes some particular application's udp6 payloads whose length are
between (MTU - IPv6 Header) and MTU were fragmented by ip6_fragment even
though the rst->dev support UFO feature.
Add the length of ipv6 header to length in __ip6_append_data to keep
consistent conditional judgement as ip6_finish_output for ip6 fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Boyd [Wed, 21 Dec 2016 22:03:42 +0000 (16:03 -0600)]
arm64: dts: msm8996: Add required memory carveouts
This patch adds required memory carveouts so that the kernel does not
access memory that is in use or has been reserved for use by other remote
processors.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Colin Ian King [Wed, 28 Dec 2016 16:44:23 +0000 (16:44 +0000)]
net: wan: slic_ds26522: fix spelling mistake: "configurated" -> "configured"
trivial fix to spelling mistake in pr_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Augusto Mecking Caringi [Wed, 28 Dec 2016 16:02:05 +0000 (16:02 +0000)]
net: atm: Fix warnings in net/atm/lec.c when !CONFIG_PROC_FS
This patch fixes the following warnings when CONFIG_PROC_FS is not set:
linux/net/atm/lec.c: In function ‘lane_module_cleanup’:
linux/net/atm/lec.c:1062:27: error: ‘atm_proc_root’ undeclared (first
use in this function)
remove_proc_entry("lec", atm_proc_root);
^
linux/net/atm/lec.c:1062:27: note: each undeclared identifier is
reported only once for each function it appears in
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Dec 2016 19:36:54 +0000 (14:36 -0500)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 28-12-2016
Some fixes for mlx5 core and ethernet driver.
for -stable:
net/mlx5: Check FW limitations on log_max_qp before setting it
net/mlx5: Cancel recovery work in remove flow
net/mlx5: Avoid shadowing numa_node
net/mlx5: Mask destination mac value in ethtool steering rules
net/mlx5: Prevent setting multicast macs for VFs
net/mlx5e: Don't sync netdev state when not registered
net/mlx5e: Disable netdev after close
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 28 Dec 2016 12:58:42 +0000 (14:58 +0200)]
net/mlx5e: Disable netdev after close
Disable netdev should come after it was closed, although no harm of doing it
before -hence the MLX5E_STATE_DESTROYING bit- but it is more natural this way.
Fixes:
26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 28 Dec 2016 12:58:41 +0000 (14:58 +0200)]
net/mlx5e: Don't sync netdev state when not registered
Skip setting netdev vxlan ports and netdev rx_mode on driver load
when netdev is not yet registered.
Synchronizing with netdev state is needed only on reset flow where the
netdev remains registered for the whole reset period.
This also fixes an access before initialization of net_device.addr_list_lock
- which for some reason initialized on register_netdev - where we queued
set_rx_mode work on driver load before netdev registration.
Fixes:
26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huy Nguyen [Wed, 28 Dec 2016 12:58:40 +0000 (14:58 +0200)]
net/mlx5e: Check ets capability before initializing ets settings
During the initial setup, the ets command is sent to firmware
without checking if the HCA supports ets. This causes the invalid
command error. Add the ets capiblity check before sending firmware
command to initialize ets settings.
Fixes:
e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Wed, 28 Dec 2016 12:58:39 +0000 (14:58 +0200)]
Revert "net/mlx5: Add MPCNT register infrastructure"
This reverts commit
7f503169cabd70c1f13b9279c50eca7dfb9a7d51.
Fixes:
7f503169cabd ("net/mlx5: Add MPCNT register infrastructure")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Wed, 28 Dec 2016 12:58:38 +0000 (14:58 +0200)]
Revert "net/mlx5e: Expose PCIe statistics to ethtool"
This reverts commit
9c7262399ba12825f3ca4b00a76d8d5e77c720f5.
PCIe counters were introduced in a new firmware version, as a result users
with old firmware encountered a syndrome every 200ms due to update stats
work. This feature will be re-introduced later with appropriate capabilities
infrastructure.
Fixes:
9c7262399ba1 ("net/mlx5e: Expose PCIe statistics to ethtool")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohamad Haj Yahia [Wed, 28 Dec 2016 12:58:37 +0000 (14:58 +0200)]
net/mlx5: Prevent setting multicast macs for VFs
Need to check that VF mac address entered by the admin user is either
zero or unicast mac.
Multicast mac addresses are prohibited.
Fixes:
77256579c6b4 ('net/mlx5: E-Switch, Introduce Vport administration functions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Wed, 28 Dec 2016 12:58:36 +0000 (14:58 +0200)]
net/mlx5: Release FTE lock in error flow
Release the FTE lock when adding rule to the FTE has failed.
Fixes:
0fd758d6112f ('net/mlx5: Don't unlock fte while still using it')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Wed, 28 Dec 2016 12:58:35 +0000 (14:58 +0200)]
net/mlx5: Mask destination mac value in ethtool steering rules
We need to mask the destination mac value with the destination mac
mask when adding steering rule via ethtool.
Fixes:
1174fce8d1410 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Wed, 28 Dec 2016 12:58:34 +0000 (14:58 +0200)]
net/mlx5: Avoid shadowing numa_node
Avoid using a local variable named numa_node to avoid shadowing a public
one.
Fixes:
db058a186f98 ('net/mlx5_core: Set irq affinity hints')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Jurgens [Wed, 28 Dec 2016 12:58:33 +0000 (14:58 +0200)]
net/mlx5: Cancel recovery work in remove flow
If there is pending delayed work for health recovery it must be canceled
if the device is being unloaded.
Fixes:
05ac2c0b7438 ("net/mlx5: Fix race between PCI error handlers and health work")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noa Osherovich [Wed, 28 Dec 2016 12:58:32 +0000 (14:58 +0200)]
net/mlx5: Check FW limitations on log_max_qp before setting it
When setting HCA capabilities, set log_max_qp to be the minimum
between the selected profile's value and the HCA limitation.
Fixes:
938fe83c8dcb ('net/mlx5_core: New device capabilities...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 28 Dec 2016 12:58:31 +0000 (14:58 +0200)]
net/mlx5: Disable RoCE on the e-switch management port under switchdev mode
Under the switchdev/offloads mode, packets that don't match any
e-switch steering rule are sent towards the e-switch management
port. We use a NIC HW steering rule set per vport (uplink and VFs)
to make them be received into the host OS through the respective
vport representor netdevice.
Currnetly such missed RoCE packets will not get to this NIC steering
rule, and hence VF RoCE will not work over the slow path of the offloads
mode. This is b/c these packets will be matched by a steering rule added
by the firmware that serves RoCE traffic set on the PF NIC vport which
is also the e-switch management port under SRIOV.
Disabling RoCE on the e-switch management vport when we are in the offloads
mode, will signal to the firmware to remove their RoCE rule, and then the
missed RoCE packets will be matched by the representor NIC steering rule
as any other missed packets.
To achieve that, we disable RoCE on the PF vport. We do that by removing
(hot-unplugging) the IB device instance associated with the PF. This is
also required by our current model where the PF serves as the uplink
representor and hence only SW switching (TC, bridge, OVS) applications
and slow path vport mlx5e net-device should be running over that vport.
Fixes:
c930a3ad7453 ('net/mlx5e: Add devlink based SRIOV mode changes')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 28 Dec 2016 12:54:47 +0000 (14:54 +0200)]
net/sched: cls_flower: Fix missing addr_type in classify
Since we now use a non zero mask on addr_type, we are matching on its
value (IPV4/IPV6). So before this fix, matching on enc_src_ip/enc_dst_ip
failed in SW/classify path since its value was zero.
This patch sets the proper value of addr_type for encapsulated packets.
Fixes:
970bfcd09791 ('net/sched: cls_flower: Use mask for addr_type')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Dec 2016 02:23:06 +0000 (18:23 -0800)]
net: stmmac: Fix race between stmmac_drv_probe and stmmac_open
There is currently a small window during which the network device registered by
stmmac can be made visible, yet all resources, including and clock and MDIO bus
have not had a chance to be set up, this can lead to the following error to
occur:
[ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
stmmac_dvr_probe: warning: cannot get CSR clock
[ 473.919382] stmmaceth 0000:01:00.0: no reset control found
[ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
[ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
[ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
[ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
[ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer
[ 473.921395] libphy: PHY stmmac-1:00 not found
[ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
[ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
PHY (error: -19)
[ 473.959710] libphy: stmmac: probed
[ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID
01410cc2 at 0 IRQ POLL
(stmmac-1:00) active
[ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID
01410cc2 at 1 IRQ POLL
(stmmac-1:01)
[ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID
01410cc2 at 2 IRQ POLL
(stmmac-1:02)
[ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID
01410cc2 at 3 IRQ POLL
(stmmac-1:03)
Fix this by making sure that register_netdev() is the last thing being done,
which guarantees that the clock and the MDIO bus are available.
Fixes:
4bfcbd7abce2 ("stmmac: Move the mdio_register/_unregister in probe/remove")
Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 28 Dec 2016 01:51:36 +0000 (17:51 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a hash corruption bug in the marvell driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvell - Copy IVDIG before launching partial DMA ahash requests
Theodore Ts'o [Wed, 28 Dec 2016 00:46:27 +0000 (19:46 -0500)]
fscrypt: fix the test_dummy_encryption mount option
Commit
f1c131b45410a: "crypto: xts - Convert to skcipher" now fails
the setkey operation if the AES key is the same as the tweak key.
Previously this check was only done if FIPS mode is enabled. Now this
check is also done if weak key checking was requested. This is
reasonable, but since we were using the dummy key which was a constant
series of 0x42 bytes, it now caused dummy encrpyption test mode to
fail.
Fix this by using 0x42... and 0x24... for the two keys, so they are
different.
Fixes:
f1c131b45410a202eb45cc55980a7a9e4e4b4f40
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Wed, 28 Dec 2016 00:04:37 +0000 (16:04 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
Cihangir Akturk [Sat, 17 Dec 2016 17:42:17 +0000 (19:42 +0200)]
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
John Brooks [Fri, 23 Dec 2016 00:53:10 +0000 (00:53 +0000)]
docs: Fix build failure
The 80211.tmpl DocBook file was removed in commit
819bf593767c ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit
7ddedebb03b7 ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:
*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.
cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Mea-culpa-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Jonathan Corbet [Tue, 27 Dec 2016 19:53:44 +0000 (12:53 -0700)]
Merge tag 'v4.10-rc1' into docs-next
Linux 4.10-rc1
Tony Lindgren [Tue, 27 Dec 2016 18:29:24 +0000 (10:29 -0800)]
Merge branch 'omap-for-v4.10/legacy' into omap-for-v4.10/fixes
Markus Elfring [Sat, 3 Dec 2016 20:46:02 +0000 (21:46 +0100)]
ARM: OMAP2+: PRM: Delete an error message for a failed memory allocation
Omit an extra message for a memory allocation failure in this function.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pali Rohár [Wed, 14 Dec 2016 21:29:44 +0000 (22:29 +0100)]
ARM: dts: n900: Mark eMMC slot with no-sdio and no-sd flags
Trying to initialize eMMC slot as SDIO or SD cause failure in n900 port of
qemu. eMMC itself is not detected and is not working.
Real Nokia N900 harware does not have this problem. As eMMC is really not
SDIO or SD based such change is harmless and will fix support for qemu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Lokesh Vutla [Wed, 14 Dec 2016 08:57:03 +0000 (14:27 +0530)]
ARM: dts: dra72-evm-tps65917: Add voltage supplies to usb_phy, mmc, dss
Commit
5d080aa30681 ("ARM: dts: dra72: Add separate dtsi for tps65917")
added a separate dtsi for dra72-evm-tps65917 moving all the voltage supplies
to this file. But it missed adding voltage supplies to usb_phy, mmc,
dss and deleted from dra72-evm-common.dtsi. Adding the voltage supply
phandles to these nodes in dra72-evm-tps65917.dtsi
Fixes:
5d080aa30681 ("ARM: dts: dra72: Add separate dtsi for tps65917")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Mon, 12 Dec 2016 09:58:05 +0000 (11:58 +0200)]
ARM: dts: am57xx-idk: Put USB2 port in peripheral mode
USB2 port can be operated in dual-role mode but till we
have dual-role support in dwc3 driver let's limit this
port to peripheral mode.
If we don't do so it defaults to host mode. USB1 port
is meant for host only operation and we don't want
both ports in host only mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Mon, 12 Dec 2016 09:58:04 +0000 (11:58 +0200)]
ARM: dts: am57xx-idk: Support VBUS detection on USB2 port
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Milo Kim [Fri, 9 Dec 2016 06:28:33 +0000 (15:28 +0900)]
dt-bindings: input: Specify the interrupt number of TPS65217 power button
Specify the power button interrupt number which is from the datasheet.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Milo Kim [Fri, 9 Dec 2016 06:28:32 +0000 (15:28 +0900)]
dt-bindings: power/supply: Update TPS65217 properties
Add interrupt specifiers for USB and AC charger input. Interrupt numbers
are from the datasheet.
Fix wrong property for compatible string.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Milo Kim [Fri, 9 Dec 2016 06:28:31 +0000 (15:28 +0900)]
dt-bindings: mfd: Remove TPS65217 interrupts
Interrupt numbers are from the datasheet, so no need to keep them in
the ABI. Use the number in the DT file.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Milo Kim [Fri, 9 Dec 2016 06:28:30 +0000 (15:28 +0900)]
ARM: dts: am335x: Fix the interrupt name of TPS65217
Use 'interrupt-names' for getting the charger interrupt number.
Fixes:
1934e89a769b ("ARM: dts: am335x: Add the charger interrupt")
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Maninder Singh [Thu, 8 Dec 2016 04:10:30 +0000 (09:40 +0530)]
ARM: omap2+: fixing wrong strcat for Non-NULL terminated string
Issue caught with static analysis tool:
"Dangerous usage of 'name' (strncpy doesn't always 0-terminate it)"
Use strlcpy _includes_ the NUL terminator, and strlcat() which ensures
that it won't overflow the buffer.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Grygorii Strashko [Mon, 5 Dec 2016 03:57:44 +0000 (09:27 +0530)]
ARM: omap2+: am437x: rollback to use omap3_gptimer_timer_init()
The commit
55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x") unintentionally changes the
clocksource devices for AM437x from OMAP GP Timer to SyncTimer32K.
Unfortunately, the SyncTimer32K is starving from frequency deviation
as mentioned in commit
5b5c01359152 ("ARM: OMAP2+: AM43x: Use gptimer
as clocksource") and, as reported by Franklin [1], even its monotonic
nature is under question (most probably there is a HW issue, but it's
still under investigation).
Taking into account above facts It's reasonable to rollback to the use
of omap3_gptimer_timer_init().
[1] http://www.spinics.net/lists/linux-omap/msg127425.html
Fixes:
55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x")
Reported-by: Cooper Jr., Franklin <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Sat, 3 Dec 2016 10:57:23 +0000 (04:57 -0600)]
ARM: dts: omap3: Add DTS for Logic PD SOM-LV 37xx Dev Kit
Fixes: ("
ab8dd3aed011 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
This adds the dts file into the Makefile. This should have been included in
the original patch.
V2: Update patch description - same source code
V1: Original patch
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:41 +0000 (11:44 -0300)]
ARM: dts: dra7: Add an empty chosen node to top level DTSI
Commit
55871eb6e2cc ("ARM: dts: dra7: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
55871eb6e2cc ("ARM: dts: dra7: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:40 +0000 (11:44 -0300)]
ARM: dts: dm816x: Add an empty chosen node to top level DTSI
Commit
06bfb9c19957 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
06bfb9c19957 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:39 +0000 (11:44 -0300)]
ARM: dts: dm814x: Add an empty chosen node to top level DTSI
Commit
76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kweh, Hock Leong [Tue, 27 Dec 2016 20:07:41 +0000 (04:07 +0800)]
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chun-Hao Lin [Tue, 27 Dec 2016 08:29:43 +0000 (16:29 +0800)]
r8169: add support for RTL8168 series add-on card.
This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 27 Dec 2016 02:49:54 +0000 (10:49 +0800)]
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
After commit
73b62bd085f4737679ea9afc7867fa5f99ba7d1b ("virtio-net:
remove the warning before XDP linearizing"), there's no users for
bpf_warn_invalid_xdp_buffer(), so remove it. This is a revert for
commit
f23bc46c30ca5ef58b8549434899fcbac41b2cfc.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Mon, 26 Dec 2016 16:31:27 +0000 (08:31 -0800)]
openvswitch: upcall: Fix vlan handling.
Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.
Fixes:
5108bbaddc ("openvswitch: add processing of L3 packets").
CC: Jarno Rajahalme <jarno@ovn.org>
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Sun, 25 Dec 2016 06:33:16 +0000 (14:33 +0800)]
ipv4: Namespaceify tcp_tw_reuse knob
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:38 +0000 (11:44 -0300)]
ARM: dts: am4372: Add an empty chosen node to top level DTSI
Commit
75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:37 +0000 (11:44 -0300)]
ARM: dts: am33xx: Add an empty chosen node to top level DTSI
Commit
f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:36 +0000 (11:44 -0300)]
ARM: dts: omap5: Add an empty chosen node to top level DTSI
Commit
76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:35 +0000 (11:44 -0300)]
ARM: dts: omap4: Add an empty chosen node to top level DTSI
Commit
da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:34 +0000 (11:44 -0300)]
ARM: dts: omap3: Add an empty chosen node to top level DTSI
Commit
008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Dec 2016 14:44:33 +0000 (11:44 -0300)]
ARM: dts: omap2: Add an empty chosen node to top level DTSI
Commit
d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes:
d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jani Nikula [Tue, 27 Dec 2016 10:59:38 +0000 (12:59 +0200)]
Merge tag 'gvt-fixes-2016-12-26' of https://github.com/01org/gvt-linux into drm-intel-fixes
From Zhenyu, "This is current GVT-g device model fixes for 4.10. I need
to base on v4.10-rc1 for merged vfio and KVMGT support."
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Laura Abbott [Wed, 21 Dec 2016 20:32:54 +0000 (12:32 -0800)]
crypto: testmgr - Use heap buffer for acomp test input
Christopher Covington reported a crash on aarch64 on recent Fedora
kernels:
kernel BUG at ./include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 752 Comm: cryptomgr_test Not tainted
4.9.0-11815-ge93b1cc #162
Hardware name: linux,dummy-virt (DT)
task:
ffff80007c650080 task.stack:
ffff800008910000
PC is at sg_init_one+0xa0/0xb8
LR is at sg_init_one+0x24/0xb8
...
[<
ffff000008398db8>] sg_init_one+0xa0/0xb8
[<
ffff000008350a44>] test_acomp+0x10c/0x438
[<
ffff000008350e20>] alg_test_comp+0xb0/0x118
[<
ffff00000834f28c>] alg_test+0x17c/0x2f0
[<
ffff00000834c6a4>] cryptomgr_test+0x44/0x50
[<
ffff0000080dac70>] kthread+0xf8/0x128
[<
ffff000008082ec0>] ret_from_fork+0x10/0x50
The test vectors used for input are part of the kernel image. These
inputs are passed as a buffer to sg_init_one which eventually blows up
with BUG_ON(!virt_addr_valid(buf)). On arm64, virt_addr_valid returns
false for the kernel image since virt_to_page will not return the
correct page. Fix this by copying the input vectors to heap buffer
before setting up the scatterlist.
Reported-by: Christopher Covington <cov@codeaurora.org>
Fixes:
d7db7a882deb ("crypto: acomp - update testmgr with support for acomp")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Jan Kara [Fri, 21 Oct 2016 09:33:49 +0000 (11:33 +0200)]
ext4: Simplify DAX fault path
Now that dax_iomap_fault() calls ->iomap_begin() without entry lock, we
can use transaction starting in ext4_iomap_begin() and thus simplify
ext4_dax_fault(). It also provides us proper retries in case of ENOSPC.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 19 Oct 2016 12:34:31 +0000 (14:34 +0200)]
dax: Call ->iomap_begin without entry lock during dax fault
Currently ->iomap_begin() handler is called with entry lock held. If the
filesystem held any locks between ->iomap_begin() and ->iomap_end()
(such as ext4 which will want to hold transaction open), this would cause
lock inversion with the iomap_apply() from standard IO path which first
calls ->iomap_begin() and only then calls ->actor() callback which grabs
entry locks for DAX (if it faults when copying from/to user provided
buffers).
Fix the problem by nesting grabbing of entry lock inside ->iomap_begin()
- ->iomap_end() pair.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 19 Oct 2016 12:48:38 +0000 (14:48 +0200)]
dax: Finish fault completely when loading holes
The only case when we do not finish the page fault completely is when we
are loading hole pages into a radix tree. Avoid this special case and
finish the fault in that case as well inside the DAX fault handler. It
will allow us for easier iomap handling.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 15:10:28 +0000 (17:10 +0200)]
dax: Avoid page invalidation races and unnecessary radix tree traversals
Currently dax_iomap_rw() takes care of invalidating page tables and
evicting hole pages from the radix tree when write(2) to the file
happens. This invalidation is only necessary when there is some block
allocation resulting from write(2). Furthermore in current place the
invalidation is racy wrt page fault instantiating a hole page just after
we have invalidated it.
So perform the page invalidation inside dax_iomap_actor() where we can
do it only when really necessary and after blocks have been allocated so
nobody will be instantiating new hole pages anymore.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 15:22:44 +0000 (17:22 +0200)]
mm: Invalidate DAX radix tree entries only if appropriate
Currently invalidate_inode_pages2_range() and invalidate_mapping_pages()
just delete all exceptional radix tree entries they find. For DAX this
is not desirable as we track cache dirtiness in these entries and when
they are evicted, we may not flush caches although it is necessary. This
can for example manifest when we write to the same block both via mmap
and via write(2) (to different offsets) and fsync(2) then does not
properly flush CPU caches when modification via write(2) was the last
one.
Create appropriate DAX functions to handle invalidation of DAX entries
for invalidate_inode_pages2_range() and invalidate_mapping_pages() and
wire them up into the corresponding mm functions.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 14:42:53 +0000 (16:42 +0200)]
ext2: Return BH_New buffers for zeroed blocks
So far we did not return BH_New buffers from ext2_get_blocks() when we
allocated and zeroed-out a block for DAX inode to avoid racy zeroing in
DAX code. This zeroing is gone these days so we can remove the
workaround.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Thomas Gleixner [Mon, 26 Dec 2016 21:58:20 +0000 (22:58 +0100)]
x86/mce/AMD: Make the init code more robust
If mce_device_init() fails then the mce device pointer is NULL and the
AMD mce code happily dereferences it.
Add a sanity check.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Mon, 26 Dec 2016 21:58:19 +0000 (22:58 +0100)]
smp/hotplug: Undo tglxs brainfart
The attempt to prevent overwriting an active state resulted in a
disaster which effectively disables all dynamically allocated hotplug
states.
Cleanup the mess.
Fixes:
dc280d936239 ("cpu/hotplug: Prevent overwriting of callbacks")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 26 Dec 2016 09:10:19 +0000 (04:10 -0500)]
arm64: don't pull uaccess.h into *.S
Split asm-only parts of arm64 uaccess.h into a new header and use that
from *.S.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Florian Fainelli [Sat, 24 Dec 2016 03:56:56 +0000 (19:56 -0800)]
net: korina: Fix NAPI versus resources freeing
Commit
beb0babfb77e ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes:
beb0babfb77e ("korina: disable napi on close and restart")
Reported-by: Alexandros C. Couloumbis <alex@ozo.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 21 Dec 2016 17:04:11 +0000 (18:04 +0100)]
net, sched: fix soft lockup in tc_classify
Shahar reported a soft lockup in tc_classify(), where we run into an
endless loop when walking the classifier chain due to tp->next == tp
which is a state we should never run into. The issue only seems to
trigger under load in the tc control path.
What happens is that in tc_ctl_tfilter(), thread A allocates a new
tp, initializes it, sets tp_created to 1, and calls into tp->ops->change()
with it. In that classifier callback we had to unlock/lock the rtnl
mutex and returned with -EAGAIN. One reason why we need to drop there
is, for example, that we need to request an action module to be loaded.
This happens via tcf_exts_validate() -> tcf_action_init/_1() meaning
after we loaded and found the requested action, we need to redo the
whole request so we don't race against others. While we had to unlock
rtnl in that time, thread B's request was processed next on that CPU.
Thread B added a new tp instance successfully to the classifier chain.
When thread A returned grabbing the rtnl mutex again, propagating -EAGAIN
and destroying its tp instance which never got linked, we goto replay
and redo A's request.
This time when walking the classifier chain in tc_ctl_tfilter() for
checking for existing tp instances we had a priority match and found
the tp instance that was created and linked by thread B. Now calling
again into tp->ops->change() with that tp was successful and returned
without error.
tp_created was never cleared in the second round, thus kernel thinks
that we need to link it into the classifier chain (once again). tp and
*back point to the same object due to the match we had earlier on. Thus
for thread B's already public tp, we reset tp->next to tp itself and
link it into the chain, which eventually causes the mentioned endless
loop in tc_classify() once a packet hits the data path.
Fix is to clear tp_created at the beginning of each request, also when
we replay it. On the paths that can cause -EAGAIN we already destroy
the original tp instance we had and on replay we really need to start
from scratch. It seems that this issue was first introduced in commit
12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining
and avoid kernel panic when we use cls_cgroup").
Fixes:
12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup")
Reported-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pei Zhang [Fri, 23 Dec 2016 15:55:08 +0000 (23:55 +0800)]
drm/i915/gvt: fix typo in cfg_space range check
PCI basic config space's size is 256 bytes. When check if access crosses
space range, should use "> 256".
Signed-off-by: Pei Zhang <pei.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Min He [Wed, 21 Dec 2016 06:54:48 +0000 (14:54 +0800)]
drm/i915/gvt: fix an issue in emulating cfg space PCI_COMMAND
There's an issue in current cfg space emulation for PCI_COMMAND (offset
0x4): when guest changes some bits other than PCI_COMMAND_MEMORY, this
write operation will not be written to virutal cfg space successfully.
This patch is to fix the wrong behavior above.
Signed-off-by: Min He <min.he@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Jike Song [Fri, 16 Dec 2016 02:51:07 +0000 (10:51 +0800)]
drm/i915/gvt/kvmgt: trival: code cleanup
Don't introduce local variables unless necessary.
Signed-off-by: Jike Song <jike.song@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Jike Song [Fri, 16 Dec 2016 02:51:06 +0000 (10:51 +0800)]
drm/i915/gvt/kvmgt: prevent double-release of vgpu
The release action might be triggered from either user's closing
mdev or the detaching event of kvm and vfio_group, so this patch
introduces an atomic to prevent double-release.
Signed-off-by: Jike Song <jike.song@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Jike Song [Fri, 16 Dec 2016 02:51:05 +0000 (10:51 +0800)]
drm/i915/gvt/kvmgt: check returned slot for gfn
gfn_to_memslot() may return NULL if the gfn is mmio
or invalid. A malicious user might input a bad gfn
to panic the host if we don't check it.
Signed-off-by: Jike Song <jike.song@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>