drm/i915: Convert flip_work to a list.

This will be required to allow more than 1 update in the future.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-10-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Allow mmio updates on all platforms, v2.

With intel_pipe_update begin/end we ensure that the mmio updates
don't run during vblank interrupt, using the hw counter we can
be sure that when current vblank count != vblank count at the time
of pipe_update_end the mmio update is complete.

This allows us to use mmio updates on all platforms, using the
update_plane call.

With Chris Wilson's patch to skip waiting for vblanks for
legacy_cursor_update this potentially leaves a small race
condition, in which update_plane can be called with a freed
crtc_state. Because of this commit acf4e84d61673
("drm/i915: Avoid stalling on pending flips for legacy cursor updates")
is temporarily reverted.

Changes since v1:
- Split out the flip_work rename.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-9-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"

This reverts commit acf4e84d6167317ff21be5c03e1ea76ea5783701.
Unfortunately this breaks the next commit with a use-after-free, so
temporarily revert until we can apply a solution.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-8-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Unify unpin_work and mmio_work into flip_work, v2.

Rename intel_unpin_work to intel_flip_work and use it for mmio flips
and unpinning. Use flip_queued_req to hold the wait request in the
mmio case, and the vblank counter from intel_crtc_get_vblank_counter.

MMIO flips get their own path through intel_finish_page_flip_mmio,
handled on vblank. CS page flips go through *_cs.

Changes since v1:
- Clean up destinction between MMIO and CS flips.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-7-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Add support for detecting vblanks when hw frame counter is unavailable.

This uses the newly created drm_accurate_vblank_count_and_time to accurately
get a vblank count when the hw counter is unavailable.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-6-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove intel_prepare_page_flip, v3.

Instead of calling prepare_flip right before calling finish_page_flip
do everything from prepare_page_flip in finish_page_flip.

Putting prepare and finish page_flip in a single step removes the need
for INTEL_FLIP_COMPLETE, so it can be removed. This simplifies the code
slightly.

Changes since v1:
- Invert if case to simplify code.
- Add missing barrier.
- Reword commit message.
Changes since v2:
- intel_page_flip_plane is removed.
- work->pending is turned into a bool.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove intel_finish_page_flip_plane.

This function is duplicated with intel_finish_page_flip,
and is only ever used from planes that could use the
other function anyway.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-4-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/i915: Remove stallcheck special handling, v3.

Both intel_unpin_work.pending and intel_unpin_work.enable_stall_check
were used to see if work should be enabled. By only using pending
some special cases are gone, and access to unpin_work can be simplified.

A flip could previously be queued before
stallcheck was active. With the addition of the pending member
enable_stall_check became obsolete and can thus be removed.

Use this to only access work members untilintel_mark_page_flip_active
is called, or intel_queue_mmio_flip is used. This will prevent
use-after-free, and makes it easier to verify accesses.

Changes since v1:
- Reword commit message.
- Do not access unpin_work after intel_mark_page_flip_active.
- Add the right memory barriers.
Changes since v2:
- atomic_read() needs a full smp_rmb.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>

drm/core: Add drm_accurate_vblank_count, v5.

This function is useful for gen2 intel devices which have no frame
counter, but need a way to determine the current vblank count without
racing with the vblank interrupt handler.

intel_pipe_update_start checks if no vblank interrupt will occur
during vblank evasion, but cannot check whether the vblank handler has
run to completion. This function uses the timestamps to determine
when the last vblank has happened, and interpolates from there.

Changes since v1:
- Take vblank_time_lock and don't use drm_vblank_count_and_time.
Changes since v2:
- Don't return time of last vblank.
Changes since v3:
- Change pipe to unsigned int. (Ville)
- Remove unused documentation for tv_ret. (kbuild)
Changes since v4:
- Add warning to docs when the function is useful.
- Add a WARN_ON when get_vblank_timestamp is unavailable.
- Use drm_vblank_count.

Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v4
Acked-by: David Airlie <airlied@linux.ie> #irc, v4
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>

drm/i915/bxt: reserve space for RC6 in the the GuC WOPCM

This patch resizes the GuC WOPCM (specifically on BXT)
so that the GuC and RC6 memory spaces do not overlap.

v2:
    Made calculation of WOPCM size into a separate function,
    so that it's consistent between the firmware size-check
    and the register-programming operations [Dave Gordon].

Issue: https://jira01.devtools.intel.com/browse/VIZ-6638
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Tested-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463494365-26330-1-git-send-email-david.s.gordon@intel.com

drm/i915: Simplify control flow in intel_atomic_check a bit.

- Unconditionally add plane states. Core helpers would have done this
  in drm_atomic_helper_check_modeset, doing it once more won't cause
  harm and is less fragile.

- Simplify the continue logic when disabling a pipe.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462779085-2458-1-git-send-email-daniel.vetter@ffwll.ch

drm/i915/dsi: CABC support for Panel PWM backlight control

In CABC (Content Adaptive Brightness Control) content grey level
scale can be increased while simultaneously decreasing
brightness of the backlight to achieve same perceived brightness.

The CABC is not standardized and panel vendors are free to follow
their implementation. The CABC implementaion here assumes that the
panels use standard SW register for control.

CABC is supported only when the PWM source for backlight is
from the panel.

v2 by Jani: rebase, renames, check cabc support earlier, etc.

Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/883faade74d2e598b143221ccc7df6daf4393a13.1461676337.git.jani.nikula@intel.com

drm/i915/dsi: Add DCS control for Panel PWM

If the source of the backlight PWM is from the
panel then the PWM can be controlled by DCS
command, this patch adds the support to
enable/disbale panel PWM, control backlight level
etc...

v2: Moving the CABC bkl functions to new file.(Jani)

v3: Rebase

v4: Rebase

v5: Use mipi_dsi_dcs_write() instead of mipi_dsi_dcs_write_buffer() (Jani)
    Move DCS macro`s to include/video/mipi_display.h (Jani)

v6: Rename the file to intel_dsi_panel_pwm.c
    Removing the CABC operations

v7 by Jani: renames, rebases, etc.

v8 by Jani: s/INTEL_BACKLIGHT_CABC/INTEL_BACKLIGHT_DSI_DCS/

v9 by Jani: rename init function to intel_dsi_dcs_init_backlight_funcs

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/71238a4b14b8c3a6c04070c789f09f1b4bc00a15.1461676337.git.jani.nikula@intel.com

Merge remote-tracking branch 'airlied/drm-next' into drm-intel-next-queued

Backmerge request by Jani to get at

commit 249c4f538b1aae55d41699f8bafc6cb762a7f48f
Author: Deepak M <m.deepak@intel.com>
Date:   Wed Mar 30 17:03:39 2016 +0300

    drm: Add new DCS commands in the enum list

Some simple conflicts in intel_dp.c.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

Merge tag 'topic/drm-misc-2016-05-13' of git://anongit.freedesktop.org/drm-intel into drm-next

I kinda hoped that I could still sneak in Noralf's
drm_simple_display_pipe, since there's intereset by others now (for tilcdc
at least). But it wasn't ready by a hair. Oh well.

Otherwise random stuff plus prep patches from Noralf.

* tag 'topic/drm-misc-2016-05-13' of git://anongit.freedesktop.org/drm-intel:
  drm/atomic: Add drm_atomic_helper_best_encoder()
  drm/atomic: Don't skip drm_bridge_*() calls if !drm_encoder_helper_funcs
  drm/fb-cma-helper: Hook up to DocBook and fix some docs
  drm/fb-helper: Remove mention of CONFIG_FB_DEFERRED_IO in docs
  drm/sti: include linux/seq_file.h where needed
  drm/tegra: Use lockless gem BO free callback
  drm/exynos: Use lockless gem BO free callback
  drm: Make drm_encoder_helper_funcs optional

Merge branch 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux into drm-next

Please pull this mini-series that allows ARC PGU to use
dedicated memory location as framebuffer backing storage.

* 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux:
  ARC: [axs10x] Specify reserved memory for frame buffer
  drm/arcpgu: use dedicated memory area for frame buffer

drm/i915: don't mix bitwise and logical operations for has_snoop

Also make the code more readable.

Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463148278-23193-2-git-send-email-jani.nikula@intel.com

drm/i915: Skip clearing the GGTT on full-ppgtt systems

Under full-ppgtt, access to the global GTT is carefully regulated
through hardware functions (i.e. userspace cannot read and write to
arbitrary locations in the GGTT via the GPU). With this restriction in
place, we can forgo clearing stale entries from the GGTT as they will
not be accessed.

For aliasing-ppgtt, we could almost do the same except that we do allow
userspace access to the global-GTT via execbuf in order to workraound
some quirks of certain instructions. (This execbuf path is filtered out
with EINVAL on full-ppgtt.)

The most dramatic effect this will have will be during resume, as with
full-ppgtt the GGTT is only used sparingly.

References: https://bugs.freedesktop.org/show_bug.cgi?id=94722
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-4-git-send-email-chris@chris-wilson.co.uk

drm/i915: Lazily migrate the objects after hibernation

Now that we mark the object domains for having been restored from the
hibernation image, we not need to flush everything during resume and
can instead rely on the normal domain tracking to flush only when
required. The only caveat here are objects that are pinned for use by
the hardware, whose contents must be coherent for when the device
resumes reading from then (shortly afterwards with the driver assuming
the objects are in the correct domain).

References: https://bugs.freedesktop.org/show_bug.cgi?id=94722
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-3-git-send-email-chris@chris-wilson.co.uk

drm/i915: Update domain tracking for GEM objects on hibernation

When creating the hibernation image, the CPU will read the pages of all
objects and thus conflict with our domain tracking. We need to update
our domain tracking to accurately reflect the state on restoration.

v2: Perform the domain tracking inside freeze, before the image is
written, rather than upon restoration.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-2-git-send-email-chris@chris-wilson.co.uk

drm/i915: Add distinct stubs for PM hibernation phases

Currently for handling the extra hibernation phases we just call the
equivalent suspend/resume phases. In the next couple of patches, I wish
to specialise the hibernation phases to reduce the amount of work
required for handling GEM objects.

v2: There are more! Don't forget the freeze phases.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-1-git-send-email-chris@chris-wilson.co.uk

drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)

When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.

In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.

Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.

v2:
 - Rebase; the SKL atomic WM patches that just landed changed the WM
   structure fields in intel_crtc_state slightly.  (Matt)

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: ed4a6a7ca853 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com

drm/i915: Don't leave old junk in ilk active watermarks on readout

When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.

Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.

Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9ca ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com

drm/i915: Eliminate the CDCLK_CTL RMW on BXT

All the fields in CDCLK_CTL we don't program should be left at zero, so
let's just get rid of the RMW.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Program BXT_CDCLK_CD2X_PIPE

BXT could change the CD2X divider synchronized with a single pipe.
So assuming the DE PLL frequency doesn't need to be changed, we could
change cdclk without shutting off the pipe (when only a single pipe is
enabled). In the meantime let's configure CDCLK_CTL for non-double
buffered CD2X update, although it shouldn't really matter as long as
the selected pipe is disabled when reprogramming the divider.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: s/required_vco/vco/ in skl cdclk code

The 'required' part of 'required_vco' should be obvious. Let's just call
it 'vco' for brevity.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/freq/cdclk/

Rename the generic sounding freq/frequency parameters to the cdclk
functions to 'cdclk' so that we'll know which clock we're talking about
once we have to deal with the vco frequencies as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Kill off dead code from skl_dpll0_enable()

We calculate the CDCLK_CTL value from scratch so no need to attempt
some form of RMW first.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract skl_dpll0_disable()

Make thins a bit easier to read by extracting the SKL DPLL0
disable into separate functions. We already have the enable
counterpart. Down the line this will also help make the cdclk
programming on SKL, BXT, and following platforms look rather
consistent.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Remove 10% cdclk guardband on BXT

We don't need any pixel clock vs. cdclk guardband since HSW. BXT still
tries to add one though. Get rid of it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Use skl_cdclk_decimal() on bxt

Both SKL and BXT need to fill in the "decimal" cdclk frequency into
the CDCLK_CTL register. SKL uses a small helper to do the kHz->"decimal"
conversion, whereas BXT has it open-coded. Use the helper on BXT too.

While at it, change it to round to closest rather than down. It doesn't
actually matter with the frequencies we have to deal with, but it seems
like the right thing to do.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation

BXT uses the "pch" panel fitter configuration, so we can use
ilk_max_pixel_rate() instead of intel_mode_max_pixclk() to compute the
pipe pixel rate. ilk_max_pixel_rate() will account for the pipe
scaler downscaling factor whereas intel_mode_max_pixclk() will not.

I'm pretty sure the same limitation is there on GMCH platforms, but
no one just bothered to implement the downscaling adjustment for them.
Probably should just unify the panel fitter setup more across the
platforms and use the exact same code on all platforms for this.
But in the meantime, let's at least make BXT a bit more correct.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Don't pass dev_priv to broxton_calc_cdclk()

broxton_calc_cdclk() doesn't need dev_priv for anything, so let's not
bother passing it around.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Untangle .fdi_link_train and cdclk vfunc setup

Split the .fdi_link_train and .modeset_commit_cdclk/.modeset_calc_cdclk
into two separate if ladders. Much easier to read when you're not
confusing two totally separate subjects.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract broadwell_calc_cdclk()

Try to reduce the amount of duplicated cdclk magic numbers by
moving the max_pixclk->cdclk conversion into a helper.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Drop checks for max_pixclk failures in cdclk computation

commit 565602d7501a ("drm/i915: Do not acquire crtc state to check clock during modeset, v4.")
removed the possibility that intel_mode_max_pixclk() or
ilk_max_pixel_rate() might return an error, so let's get rid of the
error checks in the callers as well.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Remove wm_config from dev_priv/intel_atomic_state

We calculate the watermark config into intel_atomic_state and then save
it into dev_priv, but never actually use it from there.  This is
left-over from some early ILK-style watermark programming designs that
got changed over time.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-18-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Reject display updates that exceed wm limitations (v2)

If we can't find any valid level 0 watermark values for the requested
atomic transaction, reject the configuration before we try to start
programming the hardware.

v2:
 - Add extra debugging output when we reject level 0 watermarks so that
   we can more easily debug how/why they were rejected.

Cc: Lyude Paul <cpaul@redhat.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-17-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Calculate watermarks during atomic 'check' (v2)

Moving watermark calculation into the check phase will allow us to to
reject display configurations for which there are no valid watermark
values before we start trying to program the hardware (although those
tests will come in a subsequent patch).

Another advantage of moving this calculation to the check phase is that
we can calculate the watermarks in a single shot as part of the atomic
transaction.  The watermark interfaces we inherited from our legacy
modesetting days are a bit broken in the atomic design because they use
per-crtc entry points but actually re-calculate and re-program something
that is really more of a global state.  That worked okay in the legacy
modesetting world because operations only ever updated a single CRTC at
a time.  However in the atomic world, a transaction can involve multiple
CRTC's, which means we wind up computing and programming the watermarks
NxN times (where N is the number of CRTC's involved).  With this patch
we eliminate the redundant re-calculation of watermark data for atomic
states (which was the cause of the WARN_ON(!wm_changed) problems that
have plagued us for a while).

We still need to work on the 'commit' side of watermark handling so that
we aren't doing redundant NxN programming of watermarks, but that's
content for future patches.

v2:
 - Bail out of skl_write_wm_values() if the CRTC isn't active.  Now that
   we set dirty_pipes to ~0 if the active pipes change (because
   we need to deal with DDB changes), we can now wind up here for
   disabled pipes, whereas we couldn't before.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89055
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463091100-13747-1-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Propagate watermark calculation failures up the call chain

Once we move watermark calculation to the atomic check phase, we'll want
to start rejecting display configurations that exceed out watermark
limits.  At the moment we just assume that there's always a valid set of
watermarks, even though this may not actually be true.  Let's prepare by
passing return codes up through the call stack in preparation.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-15-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Use a bitmask to track dirty pipe watermarks

Slightly easier to work with than an array of bools.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-14-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Allow watermark calculation on in-flight atomic state (v3)

In an upcoming patch we'll move this calculation to the atomic 'check'
phase so that the display update can be rejected early if no valid
watermark programming is possible.

v2:
 - Drop intel_pstate_for_cstate_plane() helper and add note about how
   the code needs to evolve in the future if we start allowing more than
   one pending commit against a CRTC.  (Maarten)

v3:
 - Only have skl_compute_wm_level calculate watermarks for enabled
   planes; we can just set the other planes on a CRTC to disabled
   without having to look at the plane state.  This is important because
   despite our CRTC lock we can still have racing commits that modify
   a disabled plane's property without turning it on.  (Maarten)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-13-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Calculate plane WM's from state

In a future patch we'll want to calculate plane watermarks for in-flight
atomic state rather than the already-committed state.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-12-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Drop re-allocation of DDB at atomic commit (v2)

Now that we're properly pre-allocating the DDB during the atomic check
phase and we trust that the allocation is appropriate, let's actually
use the allocation computed and not duplicate that work during the
commit phase.

v2:
 - Significant rebasing now that we can use cached data rates and
   minimum block allocations to avoid grabbing additional plane states.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-11-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Compute DDB allocation at atomic check time (v4)

Calculate the DDB blocks needed to satisfy the current atomic
transaction at atomic check time.  This is a prerequisite to calculating
SKL watermarks during the 'check' phase and rejecting any configurations
that we can't find valid watermarks for.

Due to the nature of DDB allocation, it's possible for the addition of a
new CRTC to make the watermark configuration already in use on another,
unchanged CRTC become invalid.  A change in which CRTC's are active
triggers a recompute of the entire DDB, which unfortunately means we
need to disallow any other atomic commits from racing with such an
update.  If the active CRTC's change, we need to grab the lock on all
CRTC's and run all CRTC's through their 'check' handler to recompute and
re-check their per-CRTC DDB allocations.

Note that with this patch we only compute the DDB allocation but we
don't actually use the computed values during watermark programming yet.
For ease of review/testing/bisecting, we still recompute the DDB at
watermark programming time and just WARN() if it doesn't match the
precomputed values.  A future patch will switch over to using the
precomputed values once we're sure they're being properly computed.

Another clarifying note:  DDB allocation itself shouldn't ever fail with
the algorithm we use today (i.e., we have enough DDB blocks on BXT to
support the minimum needs of the worst-case scenario of every pipe/plane
enabled at full size).  However the watermarks calculations based on the
DDB may fail and we'll be moving those to the atomic check as well in
future patches.

v2:
 - Skip DDB calculations in the rare case where our transaction doesn't
   actually touch any CRTC's at all.  Assuming at least one CRTC state
   is present in our transaction, then it means we can't race with any
   transactions that would update dev_priv->active_crtcs (which requires
   _all_ CRTC locks).

v3:
 - Also calculate DDB during initial hw readout, to prevent using
   incorrect bios values. (Maarten)

v4:
 - Use new distrust_bios_wm flag instead of skip_initial_wm (which was
   never actually set).
 - Set intel_state->active_pipe_changes instead of just realloc_pipes

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude Paul <cpaul@redhat.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-10-git-send-email-matthew.d.roper@intel.com

drm/i915: Add distrust_bios_wm flag to dev_priv (v2)

SKL-style platforms can't fully trust the watermark/DDB settings
programmed by the BIOS and need to do extra sanitization on their first
atomic update.  Add a flag to dev_priv that is set during hardware
readout and cleared at the end of the first commit.

Note that for the somewhat common case where everything is turned off
when the driver starts up, we don't need to bother with a recompute...we
know exactly what the DDB should be (all zero's) so just setup the DDB
directly in that case.

v2:
 - Move clearing of distrust_bios_wm up below the swap_state call since
   it's a more natural / self-explanatory location.  (Maarten)
 - Use dev_priv->active_crtcs to test whether any CRTC's are turned on
   during HW WM readout rather than trying to count the active CRTC's
   again ourselves.  (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-9-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Allow skl_allocate_pipe_ddb() to operate on in-flight state (v3)

We eventually want to calculate watermark values at atomic 'check' time
instead of atomic 'commit' time so that any requested configurations
that result in impossible watermark requirements are properly rejected.
The first step along this path is to allocate the DDB at atomic 'check'
time.  As we perform this transition, allow the main allocation function
to operate successfully on either an in-flight state or an
already-commited state.  Once we complete the transition in a future
patch, we'll come back and remove the unnecessary logic for the
already-committed case.

v2: Rebase/refactor; we should no longer need to grab extra plane states
    while allocating the DDB since we can pull cached data rates and
    minimum block counts from the CRTC state for any planes that aren't
    being modified by this transaction.

v3:
 - Simplify memsets to clear DDB plane entries.  (Maarten)
 - Drop a redundant memset of plane[pipe][PLANE_CURSOR] that was added
   by an earlier Coccinelle patch.  (Maarten)
 - Assign *num_active at the top of skl_ddb_get_pipe_allocation_limits()
   so that no code paths return without setting it.  (kbuild robot)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-8-git-send-email-matthew.d.roper@intel.com

drm/i915: Track whether an atomic transaction changes the active CRTC's

For the purposes of DDB re-allocation we need to know whether a
transaction changes the list of CRTC's that are active.  While
state->modeset could be used for this purpose, that would be slightly
too aggressive since it would lead us to re-allocate the DDB when a
CRTC's mode changes, but not its final active state.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-7-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Store plane minimum blocks in CRTC wm state (v2)

This will eventually allow us to re-use old values without
re-calculating them for unchanged planes (which also helps us avoid
re-grabbing extra plane states).

v2:
 -  Drop unnecessary memset's; they were meant for a later patch (which
    got reworked anyway to not need them, but were mis-rebased into this
    one.  (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-6-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Allow calculation of data rate for in-flight state (v2)

Our skl_get_total_relative_data_rate() function gets passed a crtc state
object to calculate the data rate for, but it currently always looks
up the committed plane states that correspond to that CRTC.  Let's
check whether the CRTC state is an in-flight state (meaning
cstate->state is non-NULL) and if so, use the corresponding in-flight
plane states.

We'll soon be using this function exclusively for in-flight states; at
that time we'll be able to simplify the function a bit, but for now we
allow it to be used in either mode.

v2:
 - Rebase on top of changes to cache plane data rates.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-5-git-send-email-matthew.d.roper@intel.com

drm/i915/gen9: Cache plane data rates in CRTC state

This will be important when we start calculating CRTC data rates for
in-flight CRTC states since it will allow us to calculate the total data
rate without needing to grab the plane state for any planes that aren't
updated by the transaction.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-4-git-send-email-matthew.d.roper@intel.com

drm/i915: Rename s/skl_compute_pipe_wm/skl_build_pipe_wm/

When we added atomic watermarks, we added a new display vfunc
'compute_pipe_wm' that is used to compute any pipe-specific watermark
information that we can at atomic check time.  This was a somewhat poor
naming choice since we already had a 'skl_compute_pipe_wm' function that
doesn't quite fit this model --- the existing SKL function is something
that gets used at atomic commit time, after the DDB allocation has been
determined.  Let's rename the existing SKL function to avoid confusion.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-3-git-send-email-matthew.d.roper@intel.com

drm/i915: Reorganize WM structs/unions in CRTC state

Reorganize the nested structures and unions we have for pipe watermark
data in intel_crtc_state so that platform-specific data can be added in
a more sensible manner (and save a bit of memory at the same time).

The change basically changes the organization from:

        union {
                struct intel_pipe_wm ilk;
                struct intel_pipe_wm skl;
        } optimal;

        struct intel_pipe_wm intermediate /* ILK-only */

to

        union {
                struct {
                        struct intel_pipe_wm intermediate;
                        struct intel_pipe_wm optimal;
                } ilk;

                struct {
                        struct intel_pipe_wm optimal;
                } skl;
        }

There should be no functional change here, but it will allow us to add
more platform-specific fields going forward (and more easily extend to
other platform types like VLV).

While we're at it, let's move the entire watermark substructure out to
its own structure definition to make the code slightly more readable.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-2-git-send-email-matthew.d.roper@intel.com

drm/i915: Remove redundant const from function return type

Marking function return types as const is redundant, as these are
rvalues and as such constant by definition. Code checkers and GCC will
warn about this so remove the modifier.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-5-git-send-email-imre.deak@intel.com

drm/i915: Handle error return from dma_set_coherent_mask()

A failure from these functions can lead to obscure bugs later, so it's
better not to suppress them and just fail module loading.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-4-git-send-email-imre.deak@intel.com

drm/i915: Add comments about fixed pipe->transcoder/PLL mapping

Code checkers may complain about the explicit casts between different
enum types, so add comments for known-valid cases to help future
triaging of such complaints.

v2:
- Make the comments more logical (Ville).

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-3-git-send-email-imre.deak@intel.com

drm/i915/gen9: Avoid using negative array index in skl_update_plane()

scaler_id may be negative as shown by conditions later in the function,
so don't use it as an array index in that case.

v2:
- Remove ps_ctrl while at it (Ville).

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-2-git-send-email-imre.deak@intel.com

drm/i915: Stop automatically retiring requests after a GPU hang

Following a GPU hang, we break out of the request loop in order to
unlock the struct_mutex for use by the GPU reset. However, if we retire
all the requests at that moment, we cannot identify the guilty request
after performing the reset.

v2: Not automatically retiring requests forces us to recheck for
available ringspace.

Fixes: f4457ae71fd6 ("drm/i915: Prevent leaking of -EIO from i915_wait_request()")
Testcase: igt/gem_reset_stats/ban-*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-4-git-send-email-chris@chris-wilson.co.uk

drm/i915: Stop retiring requests from busy/wait ioctls

In order to reduce the workload of the caller, we do not want to
actually have to retire requests of others when checking the busy status
of this object. This applies to both busy/wait ioctls as the wait ioctl
has a semantically equivalent mode to the busy ioctl.

At the present time, this is only a minor improvement to reduce the
workload of the busy ioctl under the struct_mutex which helps to reduce
its impact upon contention of struct_mutex. However, since it is mostly
a victim in highly contended scenarios, the impact is very minor until
we can eliminate the struct_mutex requirement for busy-ioctl in the near
future.

v2: Mention the patches intended limited impact. It is just paving the
way for greater changes whilst reducing the impact of a bugfix in the
next patch.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-3-git-send-email-chris@chris-wilson.co.uk

drm/i915: Complete pending resets before get-reset-stats ioctl

The get-reset-stats ioctls wasn't waiting for a pending reset before
reporting its statistics, and so was ignoring a hang generated by the
context that should have been reported against said context.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-2-git-send-email-chris@chris-wilson.co.uk

drm/i915: Move get-reset-stats ioctl from intel_uncore.c to i915_gem_context.c

The get-reset-stats ioctl reports upon the statistics (number of hangs,
be it as a victim or the guilty party) of a particular context. It is
semantically better as being part of i915_gem_context.c user interface,
as opposed to the hardware level access of intel_uncore.c

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-1-git-send-email-chris@chris-wilson.co.uk

drm/i915: Remove intel_limit_t typedef

The coding style documentation says the following about typedefs:

"In general, a pointer, or a struct that has elements that can
reasonably be directly accessed should _never_ be a typedef."

intel_limit_t falls in that category, so just use "struct intel_limit"
instead.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462353119-9738-3-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Remove intel_range_t and intel_p2_t typedefs

Those are only used for defining struct intel_limit, so use anonymous
structs instead.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462353119-9738-2-git-send-email-ander.conselvan.de.oliveira@intel.com

drm/i915: Remove intel_clock_t typedef

Just use "struct dpll" everywhere. That's actually shorter than
intel_clock_t.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462353119-9738-1-git-send-email-ander.conselvan.de.oliveira@intel.com

Merge tag 'drm/panel/for-4.7-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next

drm/panel: Changes for v4.7-rc1

This contains support for a bunch of new panels in the simple panel
driver along with some cleanup and support for a new Analogix HDMI to DP
bridge.

* tag 'drm/panel/for-4.7-rc1' of git://anongit.freedesktop.org/tegra/linux:
  drm/panel: simple: Add support for TPK U.S.A. LLC Fusion 7" and 10.1" panels
  drm/bridge: Add Analogix anx78xx support
  devicetree: Add ANX7814 SlimPort transmitter binding
  of: Add vendor prefix for Analogix Semiconductor
  drm/dp: Add define to set 0.5% down-spread in MAX_DOWNSPREAD register
  drm/panel: simple: Add support for Innolux AT070TN92
  drm/panel: simple: Remove useless drm_mode_set_name()
  drm/panel: simple: Set appropriate mode type
  drm/panel: simple: Add timings for the Olimex LCD-OLinuXino-4.3TS
  drm/panel: simple: Add the 7" DPI panel from Adafruit
  of: Add vendor prefix for On Tat Industrial Company.

drm/i915/guc: Add Broxton GuC firmware loading support

Issue: VIZ-7772
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: peter.antoine@intel.com
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462531373-34819-2-git-send-email-nicholas.hoath@intel.com

drm/i915/guc: Use major_minor version for filename

Load guc firmware from file with major_minor number
in filename instead of using symolic link with only
major number.

This change is so that new firmwares can only be used
with a kernel change. This in case there is a regression
with a new firmware, it won't be used by default without
some testing.

Issue: VIZ-7713
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: peter.antoine@intel.com
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Convert intel_overlay.c to use native drm_i915_private pointers

Another day, another long overdue conversion. Not much to update inside
intel_overlay.c, but still

   text    data     bss     dec     hex filename
6309547 3578778  696320 10584645  a18245 vmlinux
6309291 3578778  696320 10584389  a18145 vmlinux

a couple of hundred bytes of pointer misdirection.

Whilst here, rename the ioctl entry points to include the _ioctl suffix
so that the user entry points are clear (following the idiom).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463053403-25086-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: s/DPPL/DPLL/ for SKL DPLLs

SKL DPLLs shouldn't be called DPPLs.

Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 2edd6443e3d0 ("drm/i915: Use a table to initilize shared dplls")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462993473-8254-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>

drm/panel: simple: Add support for TPK U.S.A. LLC Fusion 7" and 10.1" panels

Add support for TPK U.S.A. LLC Fusion 7", 10.1" panels to the DRM simple
panel driver.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/bridge: Add Analogix anx78xx support

Although there are other chips from the same family that can reuse this
driver, at the moment we only tested ANX7814 chip.

The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
designed for portable devices. This driver adds initial support for HDMI
to DP pass-through mode.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Nicolas Boichat <drinkcat@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
[treding@nvidia.com: coding style, propagate regulator_get() errors]
Signed-off-by: Thierry Reding <treding@nvidia.com>

devicetree: Add ANX7814 SlimPort transmitter binding

The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
designed for portable devices.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

of: Add vendor prefix for Analogix Semiconductor

Analogix Semiconductor Inc. develops analog and mixed-signal devices for
digital media and communications interconnect applications.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/dp: Add define to set 0.5% down-spread in MAX_DOWNSPREAD register

Support of 0.5% down-spread is required for DisplayPort Specification
Version 1.1 Sink.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[treding@nvidia.com: rename to DP_MAX_DOWNSPREAD_0_5]
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/panel: simple: Add support for Innolux AT070TN92

Add support for the Innolux AT070TN92 panel.

Signed-off-by: Riccardo Bortolato <bortolato@navaltechitalia.it>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/panel: simple: Remove useless drm_mode_set_name()

drm_display_mode_from_videomode() already calls drm_mode_set_name() on
the provided mode.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[treding@nvidia.com: slightly reword commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/panel: simple: Set appropriate mode type

All modes exposed by simple panels should be tagged as driver defined
modes. Moreover, if a panel supports only one mode, this mode is
obviously the preferred one.

Doing this also fix a problem occurring when a 'video=' parameter is
passed on the kernel command line. In some cases the user provided mode
will be preferred over the simple panel ones, which might result in
unpredictable behavior.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[treding@nvidia.com: reshuffle some code for consistency]
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/panel: simple: Add timings for the Olimex LCD-OLinuXino-4.3TS

Add support for the Olimex LCD-OLinuXino-4.3TS panel to the DRM simple
panel driver.

It is a 480x272 panel connected through a 24-bits RGB interface.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/panel: simple: Add the 7" DPI panel from Adafruit

This is a basic TFT panel with a 40-pin FPC connector on it.  The
specification doesn't define timings, but the Adafruit instructions
were setting up 800x480 CVT.

v2: Add .bus_format and vsync/hsync flags.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
[treding@nvidia.com: keep entries properly sorted]
Signed-off-by: Thierry Reding <treding@nvidia.com>

of: Add vendor prefix for On Tat Industrial Company.

This is the vendor for a 7" DPI panel sold by Adafruit which I'd like
to describe in DT.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Merge branch 'drm-next-4.7' of git://people.freedesktop.org/~agd5f/linux into drm-next

More amdgpu fixes for 4.7.  Highlights:
- enable async pageflips
- UVD fixes for polaris
- lots of GPUVM fixes
- whitespace and code cleanups
- misc bug fixes

* 'drm-next-4.7' of git://people.freedesktop.org/~agd5f/linux: (32 commits)
  drm/amd/powerplay: rewrite pp_sw_init to make code readable
  drm/amdgpu/dce11: fix audio offset for asics with >7 audio pins
  drm/amdgpu: fix and cleanup user fence handling v2
  drm/amdgpu: move VM fields into job
  drm/amdgpu: move the context from the IBs into the job
  drm/amdgpu: move context switch handling into common code v2
  drm/amdgpu: move preamble IB handling into common code
  drm/amdgpu/gfx7: fix pipeline sync
  amdgpu/uvd: separate context buffer from DPB
  drm/amdgpu: use fence_context to judge ctx switch v2
  drm/amd/amdgpu:  Added more named DRM info messages for debugging
  drm/amd/amdgpu: Add name field to amd_ip_funcs (v2)
  drm/amdgpu: Support DRM_MODE_PAGE_FLIP_ASYNC (v2)
  drm/amdgpu/dce11: don't share PLLs on Polaris
  drm/amdgpu: Drop unused parameter for *get_sleep_divider_id_from_clock
  drm/amdgpu: Simplify calculation in *get_sleep_divider_id_from_clock
  drm/amdgpu: Use max macro in *get_sleep_divider_id_from_clock
  drm/amd/powerplay: Use defined constants for minium engine clock
  drm/amdgpu: add missing licenses on a couple of files
  drm/amdgpu: fetch cu_info once at init
  ...

Merge tag 'drm/tegra/for-4.7-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next

drm/tegra: Changes for v4.7-rc1

Two small changes, one getting rid of the bogus gamma table size and
another removing Terje from the MAINTAINERS file since he no longer does
any work on host1x or display.

* tag 'drm/tegra/for-4.7-rc1' of git://anongit.freedesktop.org/tegra/linux:
  MAINTAINERS: Remove Terje Bergström as Tegra DRM maintainer
  drm/tegra: Don't set a gamma table size

Merge branch 'drm-hisilicon-next' of github.com:xin3liang/linux into drm-next

misc hisilicon cleanups.

* 'drm-hisilicon-next' of github.com:xin3liang/linux:
  drm/hisilicon: Fix DRM_INFO printed issue
  drm/hisilicon: Make kirin_drm_unbind sufficient
  drm/hisilicon: Use drm_connector_register_all

Merge branch 'exynos-drm-next' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-next

 Summary:
   - expose HDMI-PHY clock to other drivers.
     . this patch was included in below patch series but I missed.
             http://www.spinics.net/lists/dri-devel/msg103097.html
   - some fixups about DECON5433 driver
     . this patch corrects vblank handling and fixes up trigger
       configuration.
   - use generic functions - gem_prime_mmap and dma_buf_mmap.
   - use DMA-Mapping API instead of specific one.
   - some code cleanups and fixeups.

* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos/decon5433: fix trigger configuration
  drm/exynos/dsi: use of_graph_get_endpoint_by_regs helper
  drm/exynos/dpi: use of_graph_get_endpoint_by_regs helper
  drm/exynos: Nuke dummy fb->dirty callback
  drm/exynos: use directly DMA mapping APIs on g2d
  drm/exynos/hdmi: Don't print error on deferral due to regulators
  drm/exynos: fix imported dma-buf to be mapped
  drm/exynos: support gem_prime_mmap
  drm/exynos: fimd: harden fimd_calc_clkdiv()
  drm/exynos: fix cancel page flip code
  drm/exynos/decon5433: do not use unnecessary software trigger
  drm/exynos/decon5433: handle vblank in vblank interrupt
  drm/exynos/hdmi: expose HDMI-PHY clock as pipeline clock

drm/amd/powerplay: rewrite pp_sw_init to make code readable

Actually, pp_sw_init executes pptable_init and backend_init orderly if
they are initialized successfully. So rewrite it to make code more
readable.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/dce11: fix audio offset for asics with >7 audio pins

Missing offset in the audio offset array.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix and cleanup user fence handling v2

We leaked the BO in the error pass, additional to that we only have
one user fence for all IBs in a job.

v2: remove white space changes

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: move VM fields into job

They are the same for all IBs.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: move the context from the IBs into the job

We only have one context for all IBs.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: move context switch handling into common code v2

It was a source of bugs to repeat that in each IP version.

v2: rename parameter

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: move preamble IB handling into common code

This fixes the handling which was completely broken when you
ad more than one preamble IB.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx7: fix pipeline sync

Need to wait on the fence as well.

Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amdgpu/uvd: separate context buffer from DPB

Updated to handle latest UVD ucode.

Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/atomic: Add drm_atomic_helper_best_encoder()

Add (struct drm_connector_helper_funcs *)->best_encoder callback helper
for connectors that support exactly 1 encoder, statically determined at
driver init time.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462982962-10530-6-git-send-email-noralf@tronnes.org

drm/atomic: Don't skip drm_bridge_*() calls if !drm_encoder_helper_funcs

Don't skip drm_bridge_*() calls if encoder->helper_private is NULL.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462982962-10530-5-git-send-email-noralf@tronnes.org

drm/fb-cma-helper: Hook up to DocBook and fix some docs

Hook up fb_cma_helper to DocBook. Remove mention of
CONFIG_FB_DEFERRED_IO in the docs, which was forgotten in the latest
version of the deferred_io patch.
Use & when referencing drm_mode_config_funcs in docs.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462982962-10530-3-git-send-email-noralf@tronnes.org

drm/fb-helper: Remove mention of CONFIG_FB_DEFERRED_IO in docs

This was forgotten to fixup in the latest version of the deferred_io
patch which made FB_DEFERRED_IO mandatory.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462982962-10530-2-git-send-email-noralf@tronnes.org

drm/amdgpu: use fence_context to judge ctx switch v2

Use of the ctx pointer is not safe, because they are likely already
be assigned to another ctx when doing comparing.

v2: recreate from scratch, avoid all unnecessary changes.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk.Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu:  Added more named DRM info messages for debugging

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Add name field to amd_ip_funcs (v2)

Add name that we can print out in kernel messages
to aid in debugging.

v2: drop DAL changes for upstream

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>