Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:11 +0000 (20:32 +0100)]
pata_legacy: fix access to control register for QDI6580
We need to mask out the port offset from the port number
cached in ld_qdi->timing.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:11 +0000 (20:32 +0100)]
pata_legacy: fix QDI6580DP support
Dual port QDI6580 has shared PIO timings for master/slave
devices so it needs to use custom ->qc_issue method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:11 +0000 (20:32 +0100)]
pata_it8213: fix it8213_pre_reset() documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:10 +0000 (20:32 +0100)]
pata_it8213: fix wrong MWDMA timings being programmed
Clear old MWDMA timings before programming new ones (IT8213
is a single port host so there is no need to check ap->port_no).
This change should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:10 +0000 (20:32 +0100)]
pata_it8213: fix PIO2 underclocking
[ port of Sergei's fixes for pata_efar from commit
5f33b3b ]
Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:10 +0000 (20:32 +0100)]
pata_it8213: fix wrong PIO timings being programmed
* do not clear PIO timings for master when programming slave
* program new PIO timings in the correct register nibble
Both changes should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:10 +0000 (20:32 +0100)]
pata_it8213: fix UDMA handling
Driver should program the cycle timing not the mode number
(doing the latter results in wrong timings being used).
There shouldn't be any problems with it as IDE it8213 host driver
has been doing it this way for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:10 +0000 (20:32 +0100)]
pata_hpt3x3: Power Management fix
Fix ->resume method to re-enable & re-init PCI device properly
before doing chipset specific setup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:09 +0000 (20:32 +0100)]
pata_cs5520: remove dead VDMA support
It has been dead for the last three years (== since the initial driver
merge) and probability that it will ever get fixed is quite low.
Since there is no reason to keep this dead code around any longer just
remove it (it can still be retrieved from the git history if necessary).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:08 +0000 (20:32 +0100)]
pata_efar: fix wrong MWDMA timings being programmed
Do not clear MWDMA timings for device on the other port when
programming slave device.
This change should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:08 +0000 (20:32 +0100)]
pata_efar: fix wrong PIO timings being programmed
* do not clear PIO timings for master when programming slave
* do not clear PIO timings for device on the other port when
programming slave device
Both changes should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 3 Dec 2009 19:32:08 +0000 (20:32 +0100)]
ata_piix: fix MWDMA handling on PIIX3
Fix erroneous check for ap->udma_mask in do_pata_set_dmamode()
resulting in controller not being programmed properly for MWDMA.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Wed, 25 Nov 2009 17:12:48 +0000 (18:12 +0100)]
libata: add private driver field to struct ata_device
This brings struct ata_device in-line with struct ata_{port,host}.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Nelson [Sun, 22 Nov 2009 01:07:41 +0000 (12:07 +1100)]
ahci: let users know that Promise PDC42819 support is limited to SATA devices
ahci can drive the Promise PDC42819, but obviously it can only use SATA
disks connected to this controller. The controller can actually support
SAS disks as well, but we only know how to use it in it's AHCI mode.
Add a message to let users know that because ahci is driving their chip
they can only use the SATA disks connected to this controller.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov [Tue, 24 Nov 2009 18:54:49 +0000 (22:54 +0400)]
ata: use pci_dev->revision
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit
44c10138fd4bbc4b6d6bff0873c24902f2a9da65
(PCI: Change all drivers to use pci_device->revision).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov [Tue, 24 Nov 2009 20:17:31 +0000 (00:17 +0400)]
pata_hpt366: fix timing register documentation
The comment in the driver actually describes HPT37x's timing register layout,
which is different from HPT36x. Fix it and reformat the comment, while at it.
Bump the driver version, accounting for several patches that forgot to do it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 26 Nov 2009 16:11:16 +0000 (17:11 +0100)]
libata: add comment documenting PIO latency issues on UP
Based on:
http://lkml.indiana.edu/hypermail/linux/kernel/0908.2/01420.html
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov [Fri, 27 Nov 2009 18:29:02 +0000 (22:29 +0400)]
pata_hpt{37x|3x2n}: fix timing register masks (take 2)
These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes. Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...
However, the drivers added some breakage of their own too: the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...
Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Mon, 30 Nov 2009 13:23:11 +0000 (13:23 +0000)]
pata_piccolo: Driver for old Toshiba chipsets
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Mon, 30 Nov 2009 13:23:05 +0000 (13:23 +0000)]
pata_ali: Fix regression with old devices
Making the new stuff work broke some of the old chipsets. We need to go
back to the old set up values for these it seems. Unfortunately even with
documentation this is basically a mix of cargoculting and guesswork.
Chased down to the exact line by Gianluca.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Mon, 30 Nov 2009 13:23:00 +0000 (13:23 +0000)]
[libata] PATA: Update experimental tags
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Mon, 30 Nov 2009 13:22:54 +0000 (13:22 +0000)]
pata_cmd64x: implement serialization as per notes
Daniela Engert pointed out that there are some implementation notes for the
643 and 646 that deal with certain serialization rules. In theory we don't
need them because they apply when the motherboard decides not to retry PCI
requests for long enough and the chip is busy doing a DMA transfer on the
other channel.
The rule basically is "don't touch the taskfile of the other channel while
a DMA is in progress". To implement that we need to
- not issue a command on a channel when there is a DMA command queued
- not issue a DMA command on a channel when there are PIO commands queued
- use the alternative access to the interrupt source so that we do not
touch altstatus or status on shared IRQ.
Updated to remote extra conditional check Bartlomiej noted and to remove
the variables for irq checks as the CMD648 doesn't have the underlying problem.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Mon, 30 Nov 2009 13:22:49 +0000 (13:22 +0000)]
pata_sis: Implement MWDMA for the UDMA 133 capable chips
Bartlomiej pointed out that while this got fixed in the old driver whoever
did it didn't port it across.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Mon, 30 Nov 2009 13:22:43 +0000 (13:22 +0000)]
pata_via: Blacklist some combinations of Transcend Flash and via
Reported by Mikulas Patocka.
VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Benjamin Herrenschmidt [Wed, 2 Dec 2009 00:36:28 +0000 (11:36 +1100)]
libata/sff: Use ops->bmdma_stop instead of ata_bmdma_stop()
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Christoph Hellwig [Tue, 17 Nov 2009 15:00:47 +0000 (10:00 -0500)]
libata: add translation for SCSI WRITE SAME (aka TRIM support)
Add support for the ATA TRIM command in libata. We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.
Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 19 Nov 2009 06:36:45 +0000 (15:36 +0900)]
libata: retry failed FLUSH if device didn't fail it
If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.
However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.
This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination. Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode. This was reported in the following bugzilla bug.
http://bugzilla.kernel.org/show_bug.cgi?id=14543
This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ashish kalra [Wed, 1 Jul 2009 15:29:43 +0000 (20:59 +0530)]
sata_fsl: Add asynchronous notification support
Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 19 Nov 2009 19:31:31 +0000 (20:31 +0100)]
pata_hpt{37x,3x2n}: add debounce delay to cable detection methods
Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.
Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 19 Nov 2009 17:38:11 +0000 (18:38 +0100)]
pata_hpt3x2n: fix cable detection
The detection was reversed between primary and secondary ports.
Fix it to match hpt366 and the vendor driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Matthew Garrett [Tue, 17 Nov 2009 16:09:03 +0000 (11:09 -0500)]
ata: Don't require newlines for link_power_management_policy
sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Otavio Salvador [Tue, 17 Nov 2009 13:11:16 +0000 (11:11 -0200)]
pata-it821x: use PCI_DEVICE_ID_RDC_D1010 define
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 19 Nov 2009 18:12:24 +0000 (19:12 +0100)]
pata_hpt37x: unify ->pre_reset methods
We can use the same ->pre_reset method for all HPT37x chipsets now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej Zolnierkiewicz [Thu, 19 Nov 2009 18:10:44 +0000 (19:10 +0100)]
pata_hpt37x: add proper cable detection methods
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Shaohua Li [Mon, 16 Nov 2009 01:56:05 +0000 (09:56 +0800)]
ahci: disable SNotification capability for ich8
I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.
It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.
PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Vivek Mahajan [Mon, 16 Nov 2009 06:19:22 +0000 (11:49 +0530)]
sata_sil24: MSI support, disabled by default
The following patch adds MSI support. Some platforms
may have broken MSI, so those are defaulted to use
legacy PCI interrupts.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Robert Hancock [Fri, 13 Nov 2009 02:13:40 +0000 (20:13 -0600)]
libata: remove experimental tag on PATA drivers
Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Thiago Farina [Sun, 8 Nov 2009 19:30:57 +0000 (14:30 -0500)]
sata_mv: Clean up hard coded array size calculation.
Use ARRAY_SIZE macro of kernel api instead.
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jiri Slaby [Wed, 4 Nov 2009 16:11:03 +0000 (17:11 +0100)]
pata_via: fix double put on isa bridge
In via_init_one, when via_isa_bridges iterator reaches
PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is
found but rev doesn't match, pci_dev_put(isa) is called twice.
Do pci_dev_put only once.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Krzysztof Halasa [Tue, 10 Nov 2009 23:58:16 +0000 (00:58 +0100)]
pata_cs5536: use 32-bit BM DMA template instead of 16-bit.
Tested on IXP425 + CS5536.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Wed, 18 Nov 2009 13:24:21 +0000 (22:24 +0900)]
libata-acpi: missing _SDD is not an error
Missing _SDD is not an error. Don't treat it as one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Thu, 3 Dec 2009 03:51:21 +0000 (19:51 -0800)]
Linux 2.6.32
Julia Lawall [Sun, 9 Aug 2009 09:42:32 +0000 (11:42 +0200)]
VIDEO: Correct use of request_region/request_mem_region
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Thu, 3 Sep 2009 13:59:01 +0000 (22:59 +0900)]
SPI: spi_txx9: Fix bit rate calculation
TXx9 SPI bit rate is calculated by:
fBR = (spi-baseclk) / (n + 1)
Fix calculation of min_speed_hz, max_speed_hz and n.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Wed, 2 Dec 2009 23:41:49 +0000 (15:41 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Correct WM831X_MAX_ISEL_VALUE
Anisse Astier [Tue, 1 Dec 2009 09:14:25 +0000 (01:14 -0800)]
Input: i8042 - add Dell Vostro 1320, 1520 and 1720 to the reset list
These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 2 Dec 2009 23:40:37 +0000 (15:40 -0800)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: revert incorrect fix for read error handling in raid1.
Rusty Russell [Tue, 1 Dec 2009 04:26:44 +0000 (14:56 +1030)]
param: don't complain about unused module parameters.
Jon confirms that recent modprobe will look in /proc/cmdline, so these
cmdline options can still be used.
See http://bugzilla.kernel.org/show_bug.cgi?id=14164
Reported-by: Adam Williamson <awilliam@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 2 Dec 2009 23:39:20 +0000 (15:39 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: RB532: Fix devices.c compilation.
MIPS: Fix MIPS I build.
Linus Torvalds [Wed, 2 Dec 2009 23:38:49 +0000 (15:38 -0800)]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[PATCH] rc32434_wdt: fix compilation failure
[WATCHDOG] rc32434_wdt.c: use resource_size()
Helge Deller [Wed, 2 Dec 2009 23:29:15 +0000 (00:29 +0100)]
modules: don't export section names of empty sections via sysfs
On the parisc architecture we face for each and every loaded kernel module
this kernel "badness warning":
sysfs: cannot create duplicate filename '/module/ac97_bus/sections/.text'
Badness at fs/sysfs/dir.c:487
Reason for that is, that on parisc all kernel modules do have multiple
.text sections due to the usage of the -ffunction-sections compiler flag
which is needed to reach all jump targets on this platform.
An objdump on such a kernel module gives:
Sections:
Idx Name Size VMA LMA File off Algn
0 .note.gnu.build-id
00000024 00000000 00000000 00000034 2**2
CONTENTS, ALLOC, LOAD, READONLY, DATA
1 .text
00000000 00000000 00000000 00000058 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
2 .text.ac97_bus_match
0000001c 00000000 00000000 00000058 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
3 .text
00000000 00000000 00000000 000000d4 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
Since the .text sections are empty (size of 0 bytes) and won't be
loaded by the kernel module loader anyway, I don't see a reason
why such sections need to be listed under
/sys/module/<module_name>/sections/<section_name> either.
The attached patch does solve this issue by not exporting section
names which are empty.
This fixes bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=14703
Signed-off-by: Helge Deller <deller@gmx.de>
CC: rusty@rustcorp.com.au
CC: akpm@linux-foundation.org
CC: James.Bottomley@HansenPartnership.com
CC: roland@redhat.com
CC: dave@hiauly1.hia.nrc.ca
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 2 Dec 2009 20:44:42 +0000 (12:44 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Initialise wm831x structure pointor for ISINK driver
Mark Brown [Mon, 30 Nov 2009 14:01:56 +0000 (14:01 +0000)]
regulator: Initialise wm831x structure pointor for ISINK driver
The version that made it into mainline missed the initialisation of the
chip handle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Florian Fainelli [Wed, 2 Dec 2009 12:07:01 +0000 (13:07 +0100)]
MIPS: RB532: Fix devices.c compilation.
We should now use dev_set_drvdata to set the driver driver_data field.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 2 Dec 2009 11:33:03 +0000 (11:33 +0000)]
MIPS: Fix MIPS I build.
Broken by
d63c63e889bbeeaa461a8addf1245f89f3ce4ece (lmo) rsp.
f1e39a4a616cd9981a9decfd5332fd07a01abb8b (kernel.org).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/746/
Linus Torvalds [Wed, 2 Dec 2009 16:21:58 +0000 (08:21 -0800)]
Merge branch 'fix' of git://git./linux/kernel/git/ycmiao/pxa-linux-2.6
* 'fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6:
[ARM] pxamci: call mmc_remove_host() before freeing resources
Daniel Mack [Tue, 1 Dec 2009 17:17:18 +0000 (18:17 +0100)]
[ARM] pxamci: call mmc_remove_host() before freeing resources
mmc_remove_host() will cause the mmc core to switch off the bus power by
eventually calling pxamci_set_ios(). This function uses the regulator or
the GPIO which have been freed already.
This causes the following Oops on module unload.
[ 49.519649] Unable to handle kernel paging request at virtual address
30303a70
[ 49.526878] pgd =
c7084000
[ 49.529563] [
30303a70] *pgd=
00000000
[ 49.533136] Internal error: Oops: 5 [#1]
[ 49.537025] last sysfs file: /sys/devices/platform/pxa27x-ohci/usb1/1-1/1-1:1.0/host0/target0:0:0/0:0:0:0/scsi_level
[ 49.547471] Modules linked in: pxamci(-) eeti_ts
[ 49.552061] CPU: 0 Not tainted (2.6.32-rc8 #322)
[ 49.557001] PC is at regulator_is_enabled+0x3c/0xbc
[ 49.561846] LR is at regulator_is_enabled+0x30/0xbc
[ 49.566691] pc : [<
c01a2448>] lr : [<
c01a243c>] psr:
60000013
[ 49.566702] sp :
c7083e70 ip :
30303a30 fp :
00000000
[ 49.578093] r10:
c705e200 r9 :
c7082000 r8 :
c705e2e0
[ 49.583280] r7 :
c7061340 r6 :
c7061340 r5 :
c7083e70 r4 :
00000000
[ 49.589759] r3 :
c04dc434 r2 :
c04dc434 r1 :
c03eecea r0 :
00000047
[ 49.596241] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 49.603329] Control:
0000397f Table:
a7084018 DAC:
00000015
[ 49.609031] Process rmmod (pid: 1101, stack limit = 0xc7082278)
[ 49.614908] Stack: (0xc7083e70 to 0xc7084000)
[ 49.619238] 3e60:
c7082000 c703c4f8 c705ea00 c04f4074
[ 49.627366] 3e80:
00000000 c705e3a0 ffffffff c0247ddc c70361a0 00000000 c705e3a0 ffffffff
[ 49.635499] 3ea0:
c705e200 bf006400 c78c4f00 c705e200 c705e3a0 ffffffff c705e200 ffffffff
[ 49.643633] 3ec0:
c04d8ac8 c02476d0 ffffffff c0247c60 c705e200 c0248678 c705e200 c0249064
[ 49.651765] 3ee0:
ffffffff bf006204 c04d8ad0 c04d8ad0 c04d8ac8 bf007490 00000880 c00440c4
[ 49.659898] 3f00:
0000b748 c01c5708 bf007490 c01c44c8 c04d8ac8 c04d8afc bf007490 c01c4570
[ 49.668031] 3f20:
bf007490 bf00750c c04f4258 c01c37a4 00000000 bf00750c c7083f44 c007b014
[ 49.676162] 3f40:
4000d000 6d617870 08006963 00000001 00000000 c7085000 00000001 00000000
[ 49.684287] 3f60:
4000d000 c7083f8c 00000001 bea01a54 00005401 c7ab1400 c00440c4 00082000
[ 49.692420] 3f80:
bf00750c 00000880 c7083f8c 00000000 4000cfa8 00000000 00000880 bea01cc8
[ 49.700552] 3fa0:
00000081 c0043f40 00000000 00000880 bea01cc8 00000880 00000006 00000000
[ 49.708677] 3fc0:
00000000 00000880 bea01cc8 00000081 00000097 0000cca4 0000b748 00000000
[ 49.716802] 3fe0:
4001a4f0 bea01cc0 00018bf4 4001a4fc 20000010 bea01cc8 a063e021 a063e421
[ 49.724958] [<
c01a2448>] (regulator_is_enabled+0x3c/0xbc) from [<
c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8)
[ 49.734836] [<
c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8) from [<
bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci])
[ 49.745044] [<
bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci]) from [<
c02476d0>] (mmc_power_off+0x50/0x58)
[ 49.754555] [<
c02476d0>] (mmc_power_off+0x50/0x58) from [<
c0247c60>] (mmc_detach_bus+0x68/0xc4)
[ 49.763207] [<
c0247c60>] (mmc_detach_bus+0x68/0xc4) from [<
c0248678>] (mmc_stop_host+0xd4/0x1bc)
[ 49.771944] [<
c0248678>] (mmc_stop_host+0xd4/0x1bc) from [<
c0249064>] (mmc_remove_host+0xc/0x20)
[ 49.780681] [<
c0249064>] (mmc_remove_host+0xc/0x20) from [<
bf006204>] (pxamci_remove+0xc8/0x174 [pxamci])
[ 49.790211] [<
bf006204>] (pxamci_remove+0xc8/0x174 [pxamci]) from [<
c01c5708>] (platform_drv_remove+0x1c/0x24)
[ 49.800164] [<
c01c5708>] (platform_drv_remove+0x1c/0x24) from [<
c01c44c8>] (__device_release_driver+0x7c/0xc4)
[ 49.810110] [<
c01c44c8>] (__device_release_driver+0x7c/0xc4) from [<
c01c4570>] (driver_detach+0x60/0x8c)
[ 49.819535] [<
c01c4570>] (driver_detach+0x60/0x8c) from [<
c01c37a4>] (bus_remove_driver+0x90/0xcc)
[ 49.828452] [<
c01c37a4>] (bus_remove_driver+0x90/0xcc) from [<
c007b014>] (sys_delete_module+0x1d8/0x254)
[ 49.837891] [<
c007b014>] (sys_delete_module+0x1d8/0x254) from [<
c0043f40>] (ret_fast_syscall+0x0/0x28)
[ 49.847145] Code:
eb06c53a e596c030 e1a0500d e59f106c (
e59c0040)
[ 49.853566] ---[ end trace
b5fa66a00cea142f ]---
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Florian Fainelli [Wed, 2 Dec 2009 12:21:23 +0000 (13:21 +0100)]
[PATCH] rc32434_wdt: fix compilation failure
This patch fixes the compilation failure of
rc32434 due to a bad module parameter description.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
H Hartley Sweeten [Wed, 25 Nov 2009 02:06:26 +0000 (21:06 -0500)]
[WATCHDOG] rc32434_wdt.c: use resource_size()
The size value passed to ioremap_nocache() is not correct.
Use resource_size() to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Randy Dunlap [Tue, 1 Dec 2009 21:17:50 +0000 (13:17 -0800)]
sysfs: fix SYSFS_DEPRECATED_V2 prompt
The SYSFS_DEPRECATED_V2 says "remove" older, deprecated features, but it
actually enables them, so correct this confusing, backwards text.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Tue, 1 Dec 2009 21:17:49 +0000 (13:17 -0800)]
rtc-x1205: reset clock to sane state after power failure
When detecting power failure, the probe function would reset the clock
time to defined state.
However, the clock's _date_ might still be bogus and a subsequent probe
fails when sanity-checking these values.
Change the power-failure fixup code to do a full setting of rtc_time,
including a valid date.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Tue, 1 Dec 2009 21:17:48 +0000 (13:17 -0800)]
rtc-x1205: fix rtc_time to y2k register value conversion
The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's
tm_year is in years since 1900.
The function translating rtc_time to register values assumes tm_year to be
years since first christmas, though, and we end up storing 0 or 1 in the
CCR_Y2K register, which the hardware does not refuse to do.
A subsequent probing of the clock fails due to the invalid value range in
the register, though.
[ And if it didn't, reading the clock would yield a bogus year because
the function translating registers to tm_year is assuming a register
value of 19 or 20. ]
This fixes the conversion from years since 1900 in tm_year to the
corresponding CCR_Y2K value of 19 or 20.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Horton [Tue, 1 Dec 2009 21:17:46 +0000 (13:17 -0800)]
aoe: prevent cache aliases
Prevent the AoE block driver from creating cache aliases of page cache
pages on machines with virtually indexed caches.
Building kernels on an AT91SAM9G20 board without this patch fails with
segmentation faults after a couple of passes.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alek Du [Tue, 1 Dec 2009 21:17:45 +0000 (13:17 -0800)]
gpio: Langwell GPIO driver bugfixes
- Remove wrong and unnecessary unmask operation
- Remove extra GEDR reading
This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sam Ravnborg [Tue, 1 Dec 2009 21:17:44 +0000 (13:17 -0800)]
kbuild: stepping down as maintainer
It has been fun but the last year or more it has been a duty and a burden.
So I leave it open for others to take over.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Anibal Monsalve Salazar <anibal@debian.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sudhakar Rajashekhara [Tue, 1 Dec 2009 21:17:43 +0000 (13:17 -0800)]
davinci: fb: fix frame buffer driver issues
Following issues have been addressed on DA8XX/OMAP-L1XX:
a. Screen misalignment during booting when frame buffer console is
enabled.
b. Driver was configured always in PSEUDOCOLOR mode. This patch
dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR
mode depending on bpp.
c. The RED and BLUE offsets were interchanged resulting in wrong
bootup logo colour.
This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Tue, 1 Dec 2009 21:17:41 +0000 (13:17 -0800)]
drivers/rtc/rtc-pcf50633.c: fix use after free in pcf50633_rtc_probe()
"rtc" is freed and then dereferenced on the next line. This patch fixes
that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 1 Dec 2009 21:17:41 +0000 (13:17 -0800)]
drivers/media/dvb/dvb-core/dvb_frontend.c: needs semaphore.h
Fixes:
v4l/dvb_frontend.c: In function 'dvb_frontend_stop':
v4l/dvb_frontend.c:707: error: implicit declaration of function 'init_MUTEX'
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14609
Reported-by: <tstrelar@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 1 Dec 2009 18:41:40 +0000 (10:41 -0800)]
Merge git://git./linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: update TODO files
Staging: hv: Fix some missing author names
Staging: hv: Fix vmbus event handler bug
Staging: hv: Fix argument order in incorrect memset invocations in hyperv driver.
Linus Torvalds [Tue, 1 Dec 2009 18:41:05 +0000 (10:41 -0800)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
USB: work around for EHCI with quirky periodic schedules
USB: musb: Fix CPPI IRQs not being signaled
USB: musb: respect usb_request->zero in control requests
USB: musb: fix ISOC Tx programming for CPPI DMAs
USB: musb: Remove unwanted message in boot log
usb: amd5536udc: fixed shared interrupt bug and warning oops
USB: ftdi_sio: Keep going when write errors are encountered.
USB: musb_gadget: fix STALL handling
USB: EHCI: don't send Clear-TT-Buffer following a STALL
Linus Torvalds [Tue, 1 Dec 2009 18:40:51 +0000 (10:40 -0800)]
Merge git://git./linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/of_serial: add missing ns16550a id
bcm63xx_uart: Fix serial driver compile breakage.
tty_port: handle the nonblocking open of a dead port corner case
Linus Torvalds [Tue, 1 Dec 2009 16:26:44 +0000 (08:26 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Loongson: Switch from flatmem to sparsemem
MIPS: Loongson: Disallow 4kB pages
MIPS: Add missing definition for MADV_HWPOISON.
MIPS: Fix build error if __xchg() is not getting inlined.
MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.
Wu Zhangjin [Tue, 1 Dec 2009 06:55:42 +0000 (14:55 +0800)]
MIPS: Loongson: Switch from flatmem to sparsemem
With flatmem hibernation for Loongson will fail, and there are also some
other problems such as broken files when using NFS or CIFS / Samba.
The config help of sparsemem says:
"This option provides some potential performance benefits, along with
decreased code complexity."
So to avoid the potential problems of FLATMEM, we disable FLATMEM directly
and use SPARSEMEM instead.
Related email thread:
http://groups.google.com/group/loongson-dev/browse_thread/thread/
b6b65890ec2b0f24/
feb43e5aa7f55d9b?show_docid=
feb43e5aa7f55d9b
Reported-by: Tatu Kilappa <tatu.kilappa@gmail.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/737/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wu Zhangjin [Tue, 1 Dec 2009 06:55:25 +0000 (14:55 +0800)]
MIPS: Loongson: Disallow 4kB pages
Currently, with PAGE_SIZE_4KB, the kernel for loongson will hang on:
Kernel panic - not syncing: Attempted to kill init!
The possible reason is the cache aliases problem:
Loongson 2F has 64kb, 4 way L1 Cache, the way size is 16kb, which is bigger
then 4kb. so, If using 4kb page size, there is cache aliases problem.
To avoid this kind of problem, extra cache flushing. The 2nd possible
solution is 16kb page size which avoids cache aliases without the need for
extra cache flushes. So we disable 4kB pages until the aliasing issue is
solved.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/736/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 26 Nov 2009 18:28:42 +0000 (18:28 +0000)]
MIPS: Add missing definition for MADV_HWPOISON.
Thanks to Joseph S. Myers for reporting this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Joseph S. Myers" <joseph@codesourcery.com>
Patchwork: http://patchwork.linux-mips.org/patch/723/
Ralf Baechle [Tue, 24 Nov 2009 13:16:02 +0000 (13:16 +0000)]
MIPS: Fix build error if __xchg() is not getting inlined.
If __xchg() is not getting inlined the outline version of the function
will have a reference to __xchg_called_with_bad_pointer() which does not
exist remaining. Fixed by using BUILD_BUG_ON() to check for allowable
operand sizes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/705/
Martin Michlmayr [Thu, 19 Nov 2009 16:40:09 +0000 (16:40 +0000)]
MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.
Some Debian users have reported that the kernel hangs early during boot on
some IP22 systems. Thomas Bogendoerfer found that this is due to a "bad
interaction between CONFIG_EARLY_PRINTK and overwritten prom memory during
early boot". Since there's no fix yet, disable CONFIG_EARLY_PRINTK for now.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Howells [Tue, 1 Dec 2009 15:36:11 +0000 (15:36 +0000)]
SLOW_WORK: Move slow_work's proc file to debugfs
Move slow_work's debugging proc file to debugfs.
Signed-off-by: David Howells <dhowells@redhat.com>
Requested-and-acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 1 Dec 2009 15:36:23 +0000 (07:36 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Fixup last users of irq_chip->typename
Alpha: Rearrange thread info flags fixing two regressions
arch/alpha/kernel: Add kmalloc NULL tests
arch/alpha/kernel/sys_ruffian.c: Use DIV_ROUND_CLOSEST
Marc Dionne [Tue, 1 Dec 2009 14:09:24 +0000 (14:09 +0000)]
CacheFiles: Update IMA counters when using dentry_open
When IMA is active, using dentry_open without updating the
IMA counters will result in free/open imbalance errors when
fput is eventually called.
Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 1 Dec 2009 13:52:08 +0000 (13:52 +0000)]
SLOW_WORK: Fix the CONFIG_MODULES=n case
Commits
3d7a641 ("SLOW_WORK: Wait for outstanding work items belonging to a
module to clear") introduced some code to make sure that all of a module's
slow-work items were complete before that module was removed, and commit
3bde31a ("SLOW_WORK: Allow a requeueable work item to sleep till the thread is
needed") further extended that, breaking it in the process if CONFIG_MODULES=n:
CC kernel/slow-work.o
kernel/slow-work.c: In function 'slow_work_execute':
kernel/slow-work.c:313: error: 'slow_work_thread_processing' undeclared (first use in this function)
kernel/slow-work.c:313: error: (Each undeclared identifier is reported only once
kernel/slow-work.c:313: error: for each function it appears in.)
kernel/slow-work.c: In function 'slow_work_wait_for_items':
kernel/slow-work.c:950: error: 'slow_work_unreg_sync_lock' undeclared (first use in this function)
kernel/slow-work.c:951: error: 'slow_work_unreg_wq' undeclared (first use in this function)
kernel/slow-work.c:961: error: 'slow_work_unreg_work_item' undeclared (first use in this function)
kernel/slow-work.c:974: error: 'slow_work_unreg_module' undeclared (first use in this function)
kernel/slow-work.c:977: error: 'slow_work_thread_processing' undeclared (first use in this function)
make[1]: *** [kernel/slow-work.o] Error 1
Fix this by:
(1) Extracting the bits of slow_work_execute() that are contingent on
CONFIG_MODULES, and the bits that should be, into inline functions and
placing them into the #ifdef'd section that defines the relevant variables
and adding stubs for moduleless kernels. This allows the removal of some
#ifdefs.
(2) #ifdef'ing out the contents of slow_work_wait_for_items() in moduleless
kernels.
The four functions related to handling module unloading synchronisation (and
their associated variables) could be offloaded into a separate .c file, but
each function is only used once and three of them are tiny, so doing so would
prevent them from being inlined.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 1 Dec 2009 13:38:45 +0000 (13:38 +0000)]
9p: fix build breakage introduced by FS-Cache
While building 2.6.32-rc8-git2 for Fedora I noticed the following thinko
in commit
201a15428bd54f83eccec8b7c64a04b8f9431204 ("FS-Cache: Handle
pages pending storage that get evicted under OOM conditions"):
fs/9p/cache.c: In function '__v9fs_fscache_release_page':
fs/9p/cache.c:346: error: 'vnode' undeclared (first use in this function)
fs/9p/cache.c:346: error: (Each undeclared identifier is reported only once
fs/9p/cache.c:346: error: for each function it appears in.)
make[2]: *** [fs/9p/cache.o] Error 1
Fix the 9P filesystem to correctly construct the argument to
fscache_maybe_release_page().
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com> [from identical patch]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [from identical patch]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown [Mon, 30 Nov 2009 13:24:18 +0000 (13:24 +0000)]
mfd: Correct WM831X_MAX_ISEL_VALUE
There was confusion between the array size and the highest ISEL
value possible.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NeilBrown [Tue, 1 Dec 2009 06:30:59 +0000 (17:30 +1100)]
md: revert incorrect fix for read error handling in raid1.
commit
4706b349f was a forward port of a fix that was needed
for SLES10. But in fact it is not needed in mainline because
the earlier commit
dd00a99e7a fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction. If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.
After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Thomas Gleixner [Tue, 1 Dec 2009 03:51:31 +0000 (22:51 -0500)]
alpha: Fixup last users of irq_chip->typename
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: Matt Turner <mattst88@gmail.com>
Michael Cree [Tue, 1 Dec 2009 03:44:40 +0000 (22:44 -0500)]
Alpha: Rearrange thread info flags fixing two regressions
The removal of the TIF_NOTIFY_RESUME flag, commit
a583f1b54249b
"remove unused TIF_NOTIFY_RESUME flag," resulted in incorrect
setting of the unaligned access control flags by the prctl syscall.
The re-addition of the TIF_NOTIFY_RESUME flag, commit
d0420c83f39f
"KEYS: Extend TIF_NOTIFY_RESUME to (almost) all architectures [try #6]"
further caused problems, namely incorrect operands to assembler code
as evidenced by:
AS arch/alpha/kernel/entry.o
arch/alpha/kernel/entry.S: Assembler messages:
arch/alpha/kernel/entry.S:326: Warning: operand out of range
(0x0000000000000406 is not between 0x0000000000000000 and
0x00000000000000ff)
Both regressions fixed by (1) rearranging TIF_NOTIFY_RESUME flag to be
in lower 8 bits of the thread info flags, and (2) making sure that
ALPHA_UAC_SHIFT matches the rearrangement of the thread info flags.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: David Howells <dhowells@redhat.com>,
Signed-off-by: Matt Turner <mattst88@gmail.com>
Linus Torvalds [Tue, 1 Dec 2009 00:47:16 +0000 (16:47 -0800)]
Merge branch 'security' of git://git./linux/kernel/git/linville/wireless-2.6
* 'security' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
mac80211: fix spurious delBA handling
mac80211: fix two remote exploits
Gernot Hillier [Fri, 27 Nov 2009 12:49:23 +0000 (13:49 +0100)]
USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 27 Nov 2009 14:17:59 +0000 (15:17 +0100)]
USB: work around for EHCI with quirky periodic schedules
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Glöckner [Tue, 17 Nov 2009 09:52:57 +0000 (15:22 +0530)]
USB: musb: Fix CPPI IRQs not being signaled
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Glöckner [Tue, 17 Nov 2009 09:52:56 +0000 (15:22 +0530)]
USB: musb: respect usb_request->zero in control requests
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ajay Kumar Gupta [Tue, 17 Nov 2009 09:52:55 +0000 (15:22 +0530)]
USB: musb: fix ISOC Tx programming for CPPI DMAs
Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.
Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ajay Kumar Gupta [Tue, 17 Nov 2009 09:52:54 +0000 (15:22 +0530)]
USB: musb: Remove unwanted message in boot log
Removes below unnecessary log of almost 28 lines during boot.
musb_hdrc: hw_ep 0shared, max 64
musb_hdrc: hw_ep 1tx, max 512
musb_hdrc: hw_ep 1rx, max 512
...
...
musb_hdrc: hw_ep 13shared, max 4096
musb_hdrc: hw_ep 14shared, max 1024
musb_hdrc: hw_ep 15shared, max 1024
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Dahlmann [Tue, 17 Nov 2009 22:18:27 +0000 (14:18 -0800)]
usb: amd5536udc: fixed shared interrupt bug and warning oops
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric W. Biederman [Wed, 18 Nov 2009 03:10:48 +0000 (19:10 -0800)]
USB: ftdi_sio: Keep going when write errors are encountered.
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Wed, 18 Nov 2009 19:51:18 +0000 (22:51 +0300)]
USB: musb_gadget: fix STALL handling
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 18 Nov 2009 16:37:15 +0000 (11:37 -0500)]
USB: EHCI: don't send Clear-TT-Buffer following a STALL
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bartlomiej Zolnierkiewicz [Wed, 21 Oct 2009 12:42:11 +0000 (14:42 +0200)]
Staging: update TODO files
Remove my mail address.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Haiyang Zhang [Mon, 23 Nov 2009 17:00:22 +0000 (17:00 +0000)]
Staging: hv: Fix some missing author names
Fix some missing author names.
They were accidentally removed by someone within Microsoft before the
files were sent for inclusion in the kernel.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Haiyang Zhang [Fri, 20 Nov 2009 16:29:17 +0000 (16:29 +0000)]
Staging: hv: Fix vmbus event handler bug
The flag ENABLE_POLLING is always enabled in original Makefile, but
accidently removed during porting to mainline kernel. The patch fixes
this bug which can cause stalled network communication. Credit needs to
go to Eric Sesterhenn <eric.sesterhenn@lsexperts.de> For pointing out a
typo in the original code as well.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>