GitHub/LineageOS/android_kernel_samsung_universal7580.git
13 years agow1: add 1-wire (w1) reset and resume command API support
Jean-François Dagenais [Thu, 26 May 2011 23:26:01 +0000 (16:26 -0700)]
w1: add 1-wire (w1) reset and resume command API support

The first patch adds generic functionnality to w1_io for Resume Command
[A5h] lots of slaves support.  I found it useful for multi-commands/reset
workflows with the same slave on a multi-slave bus.

This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.  Enjoy!

The ds1wm had Kconfig dependencies towards ARM && HAVE_CLK.  I took them
out since I was using the ds1wm on an x86_64 platform (ds1wm in a FPGA
through pcie) and found them irrelevant.

The clock freq/divisors at the top of ds1wm.c did not have the MSB set to
1.  This bit is CLK_EN which turns the whole prescaler and dividers on.
The driver never mentionned this bit either, so I just included this bit
right in the table entries.  I also took the liberty to add a couple of
entries to the table.  The spec doesn't explicitely mentions these
possibilities but the description and examination of the core shows the
prescalers & dividers can be used for more than the table explicitely
shows.  The table I enlarged still doesn't cover all possibilities, but
it's a good start.

I also made a few tweaks to a couple of the read and write algorithms
which made sense while I had my head very deep in the ds1wm documentation.
 We stressed it a lot with 10+ slaves on the bus, many ds2408, ds2431 and
ds2433 at the same time doing extensive interaction.  It proved quite
stable in our production environment.

This patch:

Add generic functionnality to w1_io for Resume Command [A5h] lots of
slaves support.

Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agokernel/profile.c: remove some duplicate code from profile_hits()
Rakib Mullick [Thu, 26 May 2011 23:26:00 +0000 (16:26 -0700)]
kernel/profile.c: remove some duplicate code from profile_hits()

profile_hits() has a common check for prof_on and prof_buffer regardless
of SMP or !SMP.  So, remove some duplicate code by splitting profile_hits
into two.

[akpm@linux-foundation.org: make do_profile_hits static]
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodrivers/char/ppdev.c: put gotten port value
Julia Lawall [Thu, 26 May 2011 23:25:59 +0000 (16:25 -0700)]
drivers/char/ppdev.c: put gotten port value

parport_find_number() calls parport_get_port() on its result, so there
should be a corresponding call to parport_put_port() before dropping the
reference.  Similar code is found in the function register_device() in the
same file.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

  // <smpl>
  @exists@
  local idexpression struct parport * x;
  expression ra,rr;
  statement S1,S2;
  @@

  x = parport_find_number(...)
  ... when != x = rr
      when any
      when != parport_put_port(x,...)
      when != if (...) { ... parport_put_port(x,...) ...}
  (
  if(<+...x...+>) S1 else S2
  |
  if(...) { ... when != x = ra
       when forall
       when != parport_put_port(x,...)
  *return...;
  }
  )
  // </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoedac,rcu: use synchronize_rcu() instead of call_rcu()+rcu_barrier()
Lai Jiangshan [Thu, 26 May 2011 23:25:58 +0000 (16:25 -0700)]
edac,rcu: use synchronize_rcu() instead of call_rcu()+rcu_barrier()

synchronize_rcu() does the stuff as needed.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agopid: fix typo in function description
Sisir Koppaka [Thu, 26 May 2011 23:25:57 +0000 (16:25 -0700)]
pid: fix typo in function description

finds is misspelt as finr. No functional change.

Signed-off-by: Sisir Koppaka <sisir.koppaka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agofs/partitions/efi.c: corrupted GUID partition tables can cause kernel oops
Timo Warns [Thu, 26 May 2011 23:25:57 +0000 (16:25 -0700)]
fs/partitions/efi.c: corrupted GUID partition tables can cause kernel oops

The kernel automatically evaluates partition tables of storage devices.
The code for evaluating GUID partitions (in fs/partitions/efi.c) contains
a bug that causes a kernel oops on certain corrupted GUID partition
tables.

This bug has security impacts, because it allows, for example, to
prepare a storage device that crashes a kernel subsystem upon connecting
the device (e.g., a "USB Stick of (Partial) Death").

crc = efi_crc32((const unsigned char *) (*gpt), le32_to_cpu((*gpt)->header_size));

computes a CRC32 checksum over gpt covering (*gpt)->header_size bytes.
There is no validation of (*gpt)->header_size before the efi_crc32 call.

A corrupted partition table may have large values for (*gpt)->header_size.
 In this case, the CRC32 computation access memory beyond the memory
allocated for gpt, which may cause a kernel heap overflow.

Validate value of GUID partition table header size.

[akpm@linux-foundation.org: fix layout and indenting]
Signed-off-by: Timo Warns <warns@pre-sense.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodrivers/char/mspec.c: use {k,v}zalloc to allocate memory
Rakib Mullick [Thu, 26 May 2011 23:25:56 +0000 (16:25 -0700)]
drivers/char/mspec.c: use {k,v}zalloc to allocate memory

Let memory allocator initialize the allocated memory as null, thus remove
the use of memset.

Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoipmi: convert to seq_file interface
Alexey Dobriyan [Thu, 26 May 2011 23:25:55 +0000 (16:25 -0700)]
ipmi: convert to seq_file interface

The ->read_proc interface is going away, convert to seq_file.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc:Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agofs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages
Olaf Hering [Thu, 26 May 2011 23:25:54 +0000 (16:25 -0700)]
fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages

The balloon driver in a Xen guest frees guest pages and marks them as
mmio.  When the kernel crashes and the crash kernel attempts to read the
oldmem via /proc/vmcore a read from ballooned pages will generate 100%
load in dom0 because Xen asks qemu-dm for the page content.  Since the
reads come in as 8byte requests each ballooned page is tried 512 times.

With this change a hook can be registered which checks wether the given
pfn is really ram.  The hook has to return a value > 0 for ram pages, a
value < 0 on error (because the hypercall is not known) and 0 for non-ram
pages.

This will reduce the time to read /proc/vmcore.  Without this change a
512M guest with 128M crashkernel region needs 200 seconds to read it, with
this change it takes just 2 seconds.

Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoproc: fix pagemap_read() error case
KOSAKI Motohiro [Thu, 26 May 2011 23:25:53 +0000 (16:25 -0700)]
proc: fix pagemap_read() error case

Currently, pagemap_read() has three error and/or corner case handling
mistake.

 (1) If ppos parameter is wrong, mm refcount will be leak.
 (2) If count parameter is 0, mm refcount will be leak too.
 (3) If the current task is sleeping in kmalloc() and the system
     is out of memory and oom-killer kill the proc associated task,
     mm_refcount prevent the task free its memory. then system may
     hang up.

<Quote Hugh's explain why we shold call kmalloc() before get_mm()>

  check_mem_permission gets a reference to the mm.  If we
  __get_free_page after check_mem_permission, imagine what happens if the
  system is out of memory, and the mm we're looking at is selected for
  killing by the OOM killer: while we wait in __get_free_page for more
  memory, no memory is freed from the selected mm because it cannot reach
  exit_mmap while we hold that reference.

This patch fixes the above three.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jovi Zhang <bookjovi@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Stephen Wilson <wilsons@start.ca>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoproc: put check_mem_permission after __get_free_page in mem_write
KOSAKI Motohiro [Thu, 26 May 2011 23:25:52 +0000 (16:25 -0700)]
proc: put check_mem_permission after __get_free_page in mem_write

It whould be better if put check_mem_permission after __get_free_page in
mem_write, to be same as function mem_read.

Hugh Dickins explained the reason.

    check_mem_permission gets a reference to the mm.  If we __get_free_page
    after check_mem_permission, imagine what happens if the system is out
    of memory, and the mm we're looking at is selected for killing by the
    OOM killer: while we wait in __get_free_page for more memory, no memory
    is freed from the selected mm because it cannot reach exit_mmap while
    we hold that reference.

Reported-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Stephen Wilson <wilsons@start.ca>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoproc/stat: use defined macro KMALLOC_MAX_SIZE
Yuanhan Liu [Thu, 26 May 2011 23:25:51 +0000 (16:25 -0700)]
proc/stat: use defined macro KMALLOC_MAX_SIZE

There is a macro for the max size kmalloc can allocate, so use it instead
of a hardcoded number.

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoproc: constify status array
Mike Frysinger [Thu, 26 May 2011 23:25:51 +0000 (16:25 -0700)]
proc: constify status array

No need for this local array to be writable, so mark it const.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agofs/proc: convert to kstrtoX()
Alexey Dobriyan [Thu, 26 May 2011 23:25:50 +0000 (16:25 -0700)]
fs/proc: convert to kstrtoX()

Convert fs/proc/ from strict_strto*() to kstrto*() functions.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocoredump: add support for exe_file in core name
Jiri Slaby [Thu, 26 May 2011 23:25:46 +0000 (16:25 -0700)]
coredump: add support for exe_file in core name

Now, exe_file is not proc FS dependent, so we can use it to name core
file.  So we add %E pattern for core file name cration which extract path
from mm_struct->exe_file.  Then it converts slashes to exclamation marks
and pastes the result to the core file name itself.

This is useful for environments where binary names are longer than 16
character (the current->comm limitation).  Also where there are binaries
with same name but in a different path.  Further in case the binery itself
changes its current->comm after exec.

So by doing (s/$/#/ -- # is treated as git comment):

  $ sysctl kernel.core_pattern='core.%p.%e.%E'
  $ ln /bin/cat cat45678901234567890
  $ ./cat45678901234567890
  ^Z
  $ rm cat45678901234567890
  $ fg
  ^\Quit (core dumped)
  $ ls core*

we now get:

  core.2434.cat456789012345.!root!cat45678901234567890 (deleted)

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomm: extract exe_file handling from procfs
Jiri Slaby [Thu, 26 May 2011 23:25:46 +0000 (16:25 -0700)]
mm: extract exe_file handling from procfs

Setup and cleanup of mm_struct->exe_file is currently done in fs/proc/.
This was because exe_file was needed only for /proc/<pid>/exe.  Since we
will need the exe_file functionality also for core dumps (so core name can
contain full binary path), built this functionality always into the
kernel.

To achieve that move that out of proc FS to the kernel/ where in fact it
should belong.  By doing that we can make dup_mm_exe_file static.  Also we
can drop linux/proc_fs.h inclusion in fs/exec.c and kernel/fork.c.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agokgdbts: unify/generalize gdb breakpoint adjustment
Mike Frysinger [Thu, 26 May 2011 23:25:45 +0000 (16:25 -0700)]
kgdbts: unify/generalize gdb breakpoint adjustment

The Blackfin arch, like the x86 arch, needs to adjust the PC manually
after a breakpoint is hit as normally this is handled by the remote gdb.
However, rather than starting another arch ifdef mess, create a common
GDB_ADJUSTS_BREAK_OFFSET define for any arch to opt-in via their kgdb.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agosh: convert to asm-generic ptrace.h
Mike Frysinger [Thu, 26 May 2011 23:25:44 +0000 (16:25 -0700)]
sh: convert to asm-generic ptrace.h

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agox86: convert to asm-generic ptrace.h
Mike Frysinger [Thu, 26 May 2011 23:25:43 +0000 (16:25 -0700)]
x86: convert to asm-generic ptrace.h

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoBlackfin: convert to asm-generic ptrace.h
Mike Frysinger [Thu, 26 May 2011 23:25:42 +0000 (16:25 -0700)]
Blackfin: convert to asm-generic ptrace.h

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoasm-generic/ptrace.h: start a common low level ptrace helper
Mike Frysinger [Thu, 26 May 2011 23:25:39 +0000 (16:25 -0700)]
asm-generic/ptrace.h: start a common low level ptrace helper

This is a series of low level ptrace unification steps to make it easier
for common code (like KGDB) to poke at register state.  This also avoids
having to duplicate higher level operations for most ports which don't
have special needs for accessing things.

This patch:

This implements a bunch of helper funcs for poking the registers of a
ptrace structure.  Now common code should be able to portably update
specific registers (like kgdb updating the PC).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: add the pagefault count into memcg stats
Ying Han [Thu, 26 May 2011 23:25:38 +0000 (16:25 -0700)]
memcg: add the pagefault count into memcg stats

Two new stats in per-memcg memory.stat which tracks the number of page
faults and number of major page faults.

  "pgfault"
  "pgmajfault"

They are different from "pgpgin"/"pgpgout" stat which count number of
pages charged/discharged to the cgroup and have no meaning of reading/
writing page to disk.

It is valuable to track the two stats for both measuring application's
performance as well as the efficiency of the kernel page reclaim path.
Counting pagefaults per process is useful, but we also need the aggregated
value since processes are monitored and controlled in cgroup basis in
memcg.

Functional test: check the total number of pgfault/pgmajfault of all
memcgs and compare with global vmstat value:

  $ cat /proc/vmstat | grep fault
  pgfault 1070751
  pgmajfault 553

  $ cat /dev/cgroup/memory.stat | grep fault
  pgfault 1071138
  pgmajfault 553
  total_pgfault 1071142
  total_pgmajfault 553

  $ cat /dev/cgroup/A/memory.stat | grep fault
  pgfault 199
  pgmajfault 0
  total_pgfault 199
  total_pgmajfault 0

Performance test: run page fault test(pft) wit 16 thread on faulting in
15G anon pages in 16G container.  There is no regression noticed on the
"flt/cpu/s"

Sample output from pft:

  TAG pft:anon-sys-default:
    Gb  Thr CLine   User     System     Wall    flt/cpu/s fault/wsec
    15   16   1     0.67s   233.41s    14.76s   16798.546 266356.260

  +-------------------------------------------------------------------------+
      N           Min           Max        Median           Avg        Stddev
  x  10     16682.962     17344.027     16913.524     16928.812      166.5362
  +  10     16695.568     16923.896     16820.604     16824.652     84.816568
  No difference proven at 95.0% confidence

[akpm@linux-foundation.org: fix build]
[hughd@google.com: shmem fix]
Signed-off-by: Ying Han <yinghan@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: add memory.numastat api for numa statistics
Ying Han [Thu, 26 May 2011 23:25:37 +0000 (16:25 -0700)]
memcg: add memory.numastat api for numa statistics

The new API exports numa_maps per-memcg basis.  This is a piece of useful
information where it exports per-memcg page distribution across real numa
nodes.

One of the usecases is evaluating application performance by combining
this information w/ the cpu allocation to the application.

The output of the memory.numastat tries to follow w/ simiar format of
numa_maps like:

  total=<total pages> N0=<node 0 pages> N1=<node 1 pages> ...
  file=<total file pages> N0=<node 0 pages> N1=<node 1 pages> ...
  anon=<total anon pages> N0=<node 0 pages> N1=<node 1 pages> ...
  unevictable=<total anon pages> N0=<node 0 pages> N1=<node 1 pages> ...

And we have per-node:

  total = file + anon + unevictable

  $ cat /dev/cgroup/memory/memory.numa_stat
  total=250020 N0=87620 N1=52367 N2=45298 N3=64735
  file=225232 N0=83402 N1=46160 N2=40522 N3=55148
  anon=21053 N0=3424 N1=6207 N2=4776 N3=6646
  unevictable=3735 N0=794 N1=0 N2=0 N3=2941

Signed-off-by: Ying Han <yinghan@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: rename mem_cgroup_zone_nr_pages() to mem_cgroup_zone_nr_lru_pages()
Ying Han [Thu, 26 May 2011 23:25:36 +0000 (16:25 -0700)]
memcg: rename mem_cgroup_zone_nr_pages() to mem_cgroup_zone_nr_lru_pages()

The caller of the function has been renamed to zone_nr_lru_pages(), and
this is just fixing up in the memcg code.  The current name is easily to
be mis-read as zone's total number of pages.

Signed-off-by: Ying Han <yinghan@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: remove unused retry signal from reclaim
Johannes Weiner [Thu, 26 May 2011 23:25:35 +0000 (16:25 -0700)]
memcg: remove unused retry signal from reclaim

If the memcg reclaim code detects the target memcg below its limit it
exits and returns a guaranteed non-zero value so that the charge is
retried.

Nowadays, the charge side checks the memcg limit itself and does not rely
on this non-zero return value trick.

This patch removes it.  The reclaim code will now always return the true
number of pages it reclaimed on its own.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel<riel@redhat.com>
Acked-by: Ying Han<yinghan@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: fix get_scan_count() for small targets
KAMEZAWA Hiroyuki [Thu, 26 May 2011 23:25:34 +0000 (16:25 -0700)]
memcg: fix get_scan_count() for small targets

During memory reclaim we determine the number of pages to be scanned per
zone as

(anon + file) >> priority.
Assume
scan = (anon + file) >> priority.

If scan < SWAP_CLUSTER_MAX, the scan will be skipped for this time and
priority gets higher.  This has some problems.

  1. This increases priority as 1 without any scan.
     To do scan in this priority, amount of pages should be larger than 512M.
     If pages>>priority < SWAP_CLUSTER_MAX, it's recorded and scan will be
     batched, later. (But we lose 1 priority.)
     If memory size is below 16M, pages >> priority is 0 and no scan in
     DEF_PRIORITY forever.

  2. If zone->all_unreclaimabe==true, it's scanned only when priority==0.
     So, x86's ZONE_DMA will never be recoverred until the user of pages
     frees memory by itself.

  3. With memcg, the limit of memory can be small. When using small memcg,
     it gets priority < DEF_PRIORITY-2 very easily and need to call
     wait_iff_congested().
     For doing scan before priorty=9, 64MB of memory should be used.

Then, this patch tries to scan SWAP_CLUSTER_MAX of pages in force...when

  1. the target is enough small.
  2. it's kswapd or memcg reclaim.

Then we can avoid rapid priority drop and may be able to recover
all_unreclaimable in a small zones.  And this patch removes nr_saved_scan.
 This will allow scanning in this priority even when pages >> priority is
very small.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Ying Han <yinghan@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: reclaim memory from nodes in round-robin order
Ying Han [Thu, 26 May 2011 23:25:33 +0000 (16:25 -0700)]
memcg: reclaim memory from nodes in round-robin order

Presently, memory cgroup's direct reclaim frees memory from the current
node.  But this has some troubles.  Usually when a set of threads works in
a cooperative way, they tend to operate on the same node.  So if they hit
limits under memcg they will reclaim memory from themselves, damaging the
active working set.

For example, assume 2 node system which has Node 0 and Node 1 and a memcg
which has 1G limit.  After some work, file cache remains and the usages
are

   Node 0:  1M
   Node 1:  998M.

and run an application on Node 0, it will eat its foot before freeing
unnecessary file caches.

This patch adds round-robin for NUMA and adds equal pressure to each node.
When using cpuset's spread memory feature, this will work very well.

But yes, a better algorithm is needed.

[akpm@linux-foundation.org: comment editing]
[kamezawa.hiroyu@jp.fujitsu.com: fix time comparisons]
Signed-off-by: Ying Han <yinghan@google.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoMAINTAINERS: add mm/page_cgroup.c into memcg subsystem
Namhyung Kim [Thu, 26 May 2011 23:25:32 +0000 (16:25 -0700)]
MAINTAINERS: add mm/page_cgroup.c into memcg subsystem

AFAICS mm/page_cgroup.c is for memcg subsystem, but it was directed only
to generic cgroup maintainers.  Fix it.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: move page-freeing code out of lock
Namhyung Kim [Thu, 26 May 2011 23:25:31 +0000 (16:25 -0700)]
memcg: move page-freeing code out of lock

Move page-freeing code out of swap_cgroup_mutex in the hope that it could
reduce few of theoretical contentions between swapons and/or swapoffs.

This is just a cleanup, no functional changes.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: fix off-by-one when calculating swap cgroup map length
Namhyung Kim [Thu, 26 May 2011 23:25:30 +0000 (16:25 -0700)]
memcg: fix off-by-one when calculating swap cgroup map length

It allocated one more page than necessary if @max_pages was a multiple of
SC_PER_PAGE.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: mark init_section_page_cgroup() properly
Namhyung Kim [Thu, 26 May 2011 23:25:29 +0000 (16:25 -0700)]
memcg: mark init_section_page_cgroup() properly

Commit ca371c0d7e23 ("memcg: fix page_cgroup fatal error in FLATMEM")
removes call to alloc_bootmem() in the function so that it can be marked
as __meminit to reduce memory usage when MEMORY_HOTPLUG=n.

Also as the new helper function alloc_page_cgroup() is called only in the
function, it should be marked too.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: remove pointless next_mz nullification in mem_cgroup_soft_limit_reclaim()
Michal Hocko [Thu, 26 May 2011 23:25:28 +0000 (16:25 -0700)]
memcg: remove pointless next_mz nullification in mem_cgroup_soft_limit_reclaim()

next_mz is assigned to NULL if __mem_cgroup_largest_soft_limit_node
selects the same mz.  This doesn't make much sense as we assign to the
variable right in the next loop.

Compiler will probably optimize this out but it is little bit confusing
for the code reading.

Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: add the soft_limit reclaim in global direct reclaim.
Ying Han [Thu, 26 May 2011 23:25:27 +0000 (16:25 -0700)]
memcg: add the soft_limit reclaim in global direct reclaim.

We recently added the change in global background reclaim which counts the
return value of soft_limit reclaim.  Now this patch adds the similar logic
on global direct reclaim.

We should skip scanning global LRU on shrink_zone if soft_limit reclaim
does enough work.  This is the first step where we start with counting the
nr_scanned and nr_reclaimed from soft_limit reclaim into global
scan_control.

Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemcg: count the soft_limit reclaim in global background reclaim
Ying Han [Thu, 26 May 2011 23:25:25 +0000 (16:25 -0700)]
memcg: count the soft_limit reclaim in global background reclaim

The global kswapd scans per-zone LRU and reclaims pages regardless of the
cgroup. It breaks memory isolation since one cgroup can end up reclaiming
pages from another cgroup. Instead we should rely on memcg-aware target
reclaim including per-memcg kswapd and soft_limit hierarchical reclaim under
memory pressure.

In the global background reclaim, we do soft reclaim before scanning the
per-zone LRU. However, the return value is ignored. This patch is the first
step to skip shrink_zone() if soft_limit reclaim does enough work.

This is part of the effort which tries to reduce reclaiming pages in global
LRU in memcg. The per-memcg background reclaim patchset further enhances the
per-cgroup targetting reclaim, which I should have V4 posted shortly.

Try running multiple memory intensive workloads within seperate memcgs. Watch
the counters of soft_steal in memory.stat.

  $ cat /dev/cgroup/A/memory.stat | grep 'soft'
  soft_steal 240000
  soft_scan 240000
  total_soft_steal 240000
  total_soft_scan 240000

This patch:

In the global background reclaim, we do soft reclaim before scanning the
per-zone LRU.  However, the return value is ignored.

We would like to skip shrink_zone() if soft_limit reclaim does enough
work.  Also, we need to make the memory pressure balanced across per-memcg
zones, like the logic vm-core.  This patch is the first step where we
start with counting the nr_scanned and nr_reclaimed from soft_limit
reclaim into the global scan_control.

Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomm: move enum vm_event_item into a standalone header file
Andrew Morton [Thu, 26 May 2011 23:25:24 +0000 (16:25 -0700)]
mm: move enum vm_event_item into a standalone header file

enums are problematic because they cannot be forward-declared:

  akpm2:/home/akpm> cat t.c

  enum foo;

  static inline void bar(enum foo f)
  {
  }
  akpm2:/home/akpm> gcc -c t.c
  t.c:4: error: parameter 1 ('f') has incomplete type

So move the enum's definition into a standalone header file which can be used
wherever its definition is needed.

Cc: Ying Han <yinghan@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocgroup: remove the ns_cgroup
Daniel Lezcano [Thu, 26 May 2011 23:25:23 +0000 (16:25 -0700)]
cgroup: remove the ns_cgroup

The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:

  * cgroup creation is out-of-control
  * cgroup name can conflict when pids are looping
  * it is not possible to have a single process handling a lot of
    namespaces without falling in a exponential creation time
  * we may want to create a namespace without creating a cgroup

  The ns_cgroup was replaced by a compatibility flag 'clone_children',
  where a newly created cgroup will copy the parent cgroup values.
  The userspace has to manually create a cgroup and add a task to
  the 'tasks' file.

This patch removes the ns_cgroup as suggested in the following thread:

https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html

The 'cgroup_clone' function is removed because it is no longer used.

This is a userspace-visible change.  Commit 45531757b45c ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal.  Since that
time we have heard from XXX users who were affected by this.

Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocgroups: use flex_array in attach_proc
Ben Blum [Thu, 26 May 2011 23:25:21 +0000 (16:25 -0700)]
cgroups: use flex_array in attach_proc

Convert cgroup_attach_proc to use flex_array.

The cgroup_attach_proc implementation requires a pre-allocated array to
store task pointers to atomically move a thread-group, but asking for a
monolithic array with kmalloc() may be unreliable for very large groups.
Using flex_array provides the same functionality with less risk of
failure.

This is a post-patch for cgroup-procs-write.patch.

Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocgroups: make procs file writable
Ben Blum [Thu, 26 May 2011 23:25:20 +0000 (16:25 -0700)]
cgroups: make procs file writable

Make procs file writable to move all threads by tgid at once.

Add functionality that enables users to move all threads in a threadgroup
at once to a cgroup by writing the tgid to the 'cgroup.procs' file.  This
current implementation makes use of a per-threadgroup rwsem that's taken
for reading in the fork() path to prevent newly forking threads within the
threadgroup from "escaping" while the move is in progress.

Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocgroups: add per-thread subsystem callbacks
Ben Blum [Thu, 26 May 2011 23:25:19 +0000 (16:25 -0700)]
cgroups: add per-thread subsystem callbacks

Add cgroup subsystem callbacks for per-thread attachment in atomic contexts

Add can_attach_task(), pre_attach(), and attach_task() as new callbacks
for cgroups's subsystem interface.  Unlike can_attach and attach, these
are for per-thread operations, to be called potentially many times when
attaching an entire threadgroup.

Also, the old "bool threadgroup" interface is removed, as replaced by
this.  All subsystems are modified for the new interface - of note is
cpuset, which requires from/to nodemasks for attach to be globally scoped
(though per-cpuset would work too) to persist from its pre_attach to
attach_task and attach.

This is a pre-patch for cgroup-procs-writable.patch.

Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocgroups: read-write lock CLONE_THREAD forking per threadgroup
Ben Blum [Thu, 26 May 2011 23:25:18 +0000 (16:25 -0700)]
cgroups: read-write lock CLONE_THREAD forking per threadgroup

Adds functionality to read/write lock CLONE_THREAD fork()ing per-threadgroup

Add an rwsem that lives in a threadgroup's signal_struct that's taken for
reading in the fork path, under CONFIG_CGROUPS.  If another part of the
kernel later wants to use such a locking mechanism, the CONFIG_CGROUPS
ifdefs should be changed to a higher-up flag that CGROUPS and the other
system would both depend on.

This is a pre-patch for cgroup-procs-write.patch.

Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoDocumentation: configfs examples crash fix
Jiri Slaby [Thu, 26 May 2011 23:25:17 +0000 (16:25 -0700)]
Documentation: configfs examples crash fix

When configfs_register_subsystem() fails, we unregister too many
subsystems in configfs_example_init.  Decrement i by one to not unregister
non-registered subsystem.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agogetdelays: show average CPU/IO/SWAP/RECLAIM delays
Wu Fengguang [Thu, 26 May 2011 23:25:16 +0000 (16:25 -0700)]
getdelays: show average CPU/IO/SWAP/RECLAIM delays

I find it very handy to show the average delays in milliseconds.

Example output (on 100 concurrent dd reading sparse files):

  CPU             count     real total  virtual total    delay total  delay average
                    986     3223509952     3207643301    38863410579         39.415ms
  IO              count    delay total  delay average
                      0              0              0ms
  SWAP            count    delay total  delay average
                      0              0              0ms
  RECLAIM         count    delay total  delay average
                   1059     5131834899              4ms
  dd: read=0, write=0, cancelled_write=0

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Mel Gorman <mel@linux.vnet.ibm.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Reviewed-by: Satoru Moriya <satoru.moriya@hds.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoDocumentation/accounting/getdelays.c: handle sendto() failures
Andrew Morton [Thu, 26 May 2011 23:25:15 +0000 (16:25 -0700)]
Documentation/accounting/getdelays.c: handle sendto() failures

Fixes

  Documentation/accounting/getdelays.c: In function `get_family_id':
  Documentation/accounting/getdelays.c:172:14: warning: variable `rc' set but not used [-Wunused-but-set-variable]

Reported-by: "Justin P. Mattock" <justinmattock@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoDocumentation/accounting/getdelays.c: fix unused var warning
Justin P. Mattock [Thu, 26 May 2011 23:25:14 +0000 (16:25 -0700)]
Documentation/accounting/getdelays.c: fix unused var warning

Fixes

  Documentation/accounting/getdelays.c: In function `main':
  Documentation/accounting/getdelays.c:436:7: warning: variable `i' set but not used [-Wunused-but-set-variable]

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoDocumentation/atomic_ops.txt: avoid volatile in sample code
Nikanth Karthikesan [Thu, 26 May 2011 23:25:13 +0000 (16:25 -0700)]
Documentation/atomic_ops.txt: avoid volatile in sample code

As declaring counter as volatile is discouraged, it is best not to use it
in sample code as well.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoufs: fix truncated values handling 64 bit metadata
Dan Carpenter [Thu, 26 May 2011 23:25:12 +0000 (16:25 -0700)]
ufs: fix truncated values handling 64 bit metadata

Originally i_lastfrag was 32 bits but then we added support for handling
64 bit metadata and it became a 64 bit variable.  That was during 2007, in
54fb996ac15c "[PATCH] ufs2 write: block allocation update".  Unfortunately
these casts got left behind so the value got truncated to 32 bit again.

[akpm@linux-foundation.org: remove now-unneeded min_t/max_t casting]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodrivers/rtc/rtc-mxc.c: remove defines already included in rtc.h
Wolfram Sang [Thu, 26 May 2011 23:25:12 +0000 (16:25 -0700)]
drivers/rtc/rtc-mxc.c: remove defines already included in rtc.h

[akpm@linux-foundation.org: retain the code comments]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodrivers/rtc/rtc-pcf50633.c: don't request update IRQ
Lars-Peter Clausen [Thu, 26 May 2011 23:25:10 +0000 (16:25 -0700)]
drivers/rtc/rtc-pcf50633.c: don't request update IRQ

Commit 51ba60c5 ("RTC: Cleanup rtc_class_ops->update_irq_enable()")
removed the only user of the update IRQ, so there is no need to manage it
any more.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agortc: add support for spear rtc
Rajeev Kumar [Thu, 26 May 2011 23:25:09 +0000 (16:25 -0700)]
rtc: add support for spear rtc

Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodrivers/rtc/rtc-mrst.c: use release_mem_region after request_mem_region
Julia Lawall [Thu, 26 May 2011 23:25:08 +0000 (16:25 -0700)]
drivers/rtc/rtc-mrst.c: use release_mem_region after request_mem_region

The memory allocated using request_mem_region should be released using
release_mem_region, not release_region.

The semantic patch that fixes part of this problem is as follows:
(http://coccinelle.lip6.fr/)

  // <smpl>
  @@
  expression E1,E2,E3;
  @@

  request_mem_region(E1,E2,E3)
  ...
  ?- release_region(E1,E2)
  + release_mem_region(E1,E2)
  // </smpl>

[akpm@linux-foundation.org: use resource_size()]
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agortc: add basic support for ST M41T93 SPI RTC
Voss, Nikolaus [Thu, 26 May 2011 23:25:07 +0000 (16:25 -0700)]
rtc: add basic support for ST M41T93 SPI RTC

Add basic support for ST m41t93 SPI RTCs.  Tested with factory-new and
with "run-in" species with and without backup batteries.

Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agortc: add rv3029c2 RTC support
Heiko Schocher [Thu, 26 May 2011 23:25:05 +0000 (16:25 -0700)]
rtc: add rv3029c2 RTC support

Add support for the Micro Crystal RV3029-C2 RTC chips.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agortc: add EM3027 rtc driver
Mike Rapoport [Thu, 26 May 2011 23:25:04 +0000 (16:25 -0700)]
rtc: add EM3027 rtc driver

Add support for EM Microelectronic EM3027 RTC chip.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agortc: add support for the RTC in VIA VT8500 and compatibles
Alexey Charkov [Thu, 26 May 2011 23:25:03 +0000 (16:25 -0700)]
rtc: add support for the RTC in VIA VT8500 and compatibles

This adds a driver for the RTC devices in VIA and WonderMedia
Systems-on-Chip.  Alarm, 1Hz interrupts, reading and setting time are
supported.

Signed-off-by: Alexey Charkov <alchark@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alexey Charkov <alchark@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoflex_array: avoid divisions when accessing elements
Jesse Gross [Thu, 26 May 2011 23:25:02 +0000 (16:25 -0700)]
flex_array: avoid divisions when accessing elements

On most architectures division is an expensive operation and accessing an
element currently requires four of them.  This performance penalty
effectively precludes flex arrays from being used on any kind of fast
path.  However, two of these divisions can be handled at creation time and
the others can be replaced by a reciprocal divide, completely avoiding
real divisions on access.

[eparis@redhat.com: rebase on top of changes to support 0 len elements]
[eparis@redhat.com: initialize part_nr when array fits entirely in base]
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agom32r: remove redundant declaration
KOSAKI Motohiro [Thu, 26 May 2011 23:25:01 +0000 (16:25 -0700)]
m32r: remove redundant declaration

They have no meaning.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agom32r: fix spin_lock_irqsave() misuse
KOSAKI Motohiro [Thu, 26 May 2011 23:25:00 +0000 (16:25 -0700)]
m32r: fix spin_lock_irqsave() misuse

spin_lock_irqsave() requires unsigned long.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agom32r: convert cpumask api
KOSAKI Motohiro [Thu, 26 May 2011 23:24:59 +0000 (16:24 -0700)]
m32r: convert cpumask api

We plan to remove cpus_xx() old cpumask APIs later.  Also, we plan to
change mm_cpu_mask() implementation, allocate only nr_cpu_ids, thus
*mm_cpu_mask() is dangerous operation.

Then, this patch convert them.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodrivers/bcma/host_pci.c needs slab.h
Andrew Morton [Thu, 26 May 2011 23:24:57 +0000 (16:24 -0700)]
drivers/bcma/host_pci.c needs slab.h

alpha allmodconfig:

  drivers/bcma/host_pci.c: In function 'bcma_host_pci_probe':
  drivers/bcma/host_pci.c:102: error: implicit declaration of function 'kzalloc'
  drivers/bcma/host_pci.c:102: warning: assignment makes pointer from integer without a cast

Cc: <zajec5@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodrivers/video/mb862xx/mb862xxfbdrv.c needs uaccess.h
Andrew Morton [Thu, 26 May 2011 23:24:55 +0000 (16:24 -0700)]
drivers/video/mb862xx/mb862xxfbdrv.c needs uaccess.h

alpha allmodconfig:

  drivers/video/mb862xx/mb862xxfbdrv.c: In function 'mb862xxfb_ioctl':
  drivers/video/mb862xx/mb862xxfbdrv.c:323: error: implicit declaration of function 'copy_to_user'
  drivers/video/mb862xx/mb862xxfbdrv.c:327: error: implicit declaration of function 'copy_from_user'

Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoSet cred->user_ns in key_replace_session_keyring
Serge E. Hallyn [Thu, 26 May 2011 20:25:05 +0000 (15:25 -0500)]
Set cred->user_ns in key_replace_session_keyring

Since this cred was not created with copy_creds(), it needs to get
initialized.  Otherwise use of syscall(__NR_keyctl, KEYCTL_SESSION_TO_PARENT);
can lead to a NULL deref.  Thanks to Robert for finding this.

But introduced by commit 47a150edc2a ("Cache user_ns in struct cred").

Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Reported-by: Robert Święcki <robert@swiecki.net>
Cc: David Howells <dhowells@redhat.com>
Cc: stable@kernel.org (2.6.39)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoMerge branch 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
Linus Torvalds [Thu, 26 May 2011 20:19:00 +0000 (13:19 -0700)]
Merge branch 'trivial' of git://git./linux/kernel/git/mmarek/kbuild-2.6

* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  gfs2: Drop __TIME__ usage
  isdn/diva: Drop __TIME__ usage
  atm: Drop __TIME__ usage
  dlm: Drop __TIME__ usage
  wan/pc300: Drop __TIME__ usage
  parport: Drop __TIME__ usage
  hdlcdrv: Drop __TIME__ usage
  baycom: Drop __TIME__ usage
  pmcraid: Drop __DATE__ usage
  edac: Drop __DATE__ usage
  rio: Drop __DATE__ usage
  scsi/wd33c93: Drop __TIME__ usage
  scsi/in2000: Drop __TIME__ usage
  aacraid: Drop __TIME__ usage
  media/cx231xx: Drop __TIME__ usage
  media/radio-maxiradio: Drop __TIME__ usage
  nozomi: Drop __TIME__ usage
  cyclades: Drop __TIME__ usage

13 years agoMerge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Thu, 26 May 2011 19:19:31 +0000 (12:19 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: vdso: Remove unused variable
  x86-64: Optimize vDSO time()
  x86-64: Add time to vDSO
  x86-64: Turn off -pg and turn on -foptimize-sibling-calls for vDSO
  x86-64: Move vread_tsc into a new file with sensible options
  x86-64: Vclock_gettime(CLOCK_MONOTONIC) can't ever see nsec < 0
  x86-64: Don't generate cmov in vread_tsc
  x86-64: Remove unnecessary barrier in vread_tsc
  x86-64: Clean up vdso/kernel shared variables

13 years agoMerge branches 'core-fixes-for-linus' and 'irq-fixes-for-linus' of git://git.kernel...
Linus Torvalds [Thu, 26 May 2011 19:19:11 +0000 (12:19 -0700)]
Merge branches 'core-fixes-for-linus' and 'irq-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  seqlock: Get rid of SEQLOCK_UNLOCKED

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  irq: Remove smp_affinity_list when unregister irq proc

13 years agoMerge branch 'gpio/next' of git://git.secretlab.ca/git/linux-2.6
Linus Torvalds [Thu, 26 May 2011 19:14:41 +0000 (12:14 -0700)]
Merge branch 'gpio/next' of git://git.secretlab.ca/git/linux-2.6

* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
  gpio/via: rename VIA local config struct
  basic_mmio_gpio: split into a gpio library and platform device
  gpio: remove some legacy comments in build files
  gpio: add trace events for setting direction and value
  gpio/pca953x: Use handle_simple_irq instead of handle_edge_irq
  gpiolib: export gpiochip_find
  gpio: remove redundant Kconfig depends on GPIOLIB
  basic_mmio_gpio: convert to non-__raw* accessors
  basic_mmio_gpio: support direction registers
  basic_mmio_gpio: support different input/output registers
  basic_mmio_gpio: detect output method at probe time
  basic_mmio_gpio: request register regions
  basic_mmio_gpio: allow overriding number of gpio
  basic_mmio_gpio: convert to platform_{get,set}_drvdata()
  basic_mmio_gpio: remove runtime width/endianness evaluation

13 years agoMerge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Linus Torvalds [Thu, 26 May 2011 19:14:20 +0000 (12:14 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/sameo/mfd-2.6

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
  regulator: Fix 88pm8607.c printk format warning
  input: Add support for Qualcomm PMIC8XXX power key
  input: Add Qualcomm pm8xxx keypad controller driver
  mfd: Add omap-usbhs runtime PM support
  mfd: Fix ASIC3 SD Host Controller Configuration size
  mfd: Fix omap_usbhs_alloc_children error handling
  mfd: Fix omap usbhs crash when rmmoding ehci or ohci
  mfd: Add ASIC3 LED support
  leds: Add ASIC3 LED support
  mfd: Update twl4030-code maintainer e-mail address
  mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
  mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
  mfd: Provide ab8500-core enumerators for chip cuts
  mfd: Check twl4030-power remove script error condition after i2cwrite
  mfd: Fix twl6030 irq definitions
  mfd: Add phoenix lite (twl6025) support to twl6030
  mfd: Avoid to use constraint name in 88pm860x regulator driver
  mfd: Remove checking on max8925 regulator[0]
  mfd: Remove unused parameter from 88pm860x API
  mfd: Avoid to allocate 88pm860x static platform data
  ...

13 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland...
Linus Torvalds [Thu, 26 May 2011 19:13:57 +0000 (12:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cma: Save PID of ID's owner
  RDMA/cma: Add support for netlink statistics export
  RDMA/cma: Pass QP type into rdma_create_id()
  RDMA: Update exported headers list
  RDMA/cma: Export enum cma_state in <rdma/rdma_cm.h>
  RDMA/nes: Add a check for strict_strtoul()
  RDMA/cxgb3: Don't post zero-byte read if endpoint is going away
  RDMA/cxgb4: Use completion objects for event blocking
  IB/srp: Fix integer -> pointer cast warnings
  IB: Add devnode methods to cm_class and umad_class
  IB/mad: Return EPROTONOSUPPORT when an RDMA device lacks the QP required
  IB/uverbs: Add devnode method to set path/mode
  RDMA/ucma: Add .nodename/.mode to tell userspace where to create device node
  RDMA: Add netlink infrastructure
  RDMA: Add error handling to ib_core_init()

13 years agoMerge branch 'spi/next' of git://git.secretlab.ca/git/linux-2.6
Linus Torvalds [Thu, 26 May 2011 19:13:22 +0000 (12:13 -0700)]
Merge branch 'spi/next' of git://git.secretlab.ca/git/linux-2.6

* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
  spi/amba-pl022: work in polling or interrupt mode if pl022_dma_probe fails
  spi/spi_s3c24xx: Use spi_bitbang_stop instead of spi_unregister_master in s3c24xx_spi_remove
  spi/spi_nuc900: Use spi_bitbang_stop instead of spi_unregister_master in nuc900_spi_remove
  spi/spi_tegra: use spi_unregister_master() instead of spi_master_put()
  spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path
  spi: Use void pointers for data in simple SPI I/O operations
  spi/pl022: use cpu_relax in the busy loop
  spi/pl022: mark driver non-experimental
  spi/pl022: timeout on polled transfer v2
  spi/dw_spi: improve the interrupt mode with the batch ops
  spi/dw_spi: change poll mode transfer from byte ops to batch ops
  spi/dw_spi: remove the un-necessary flush()
  spi/dw_spi: unify the low level read/write routines

13 years agoMerge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind...
Linus Torvalds [Thu, 26 May 2011 19:11:54 +0000 (12:11 -0700)]
Merge branch 'omap-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
  OMAP3: PM: Boot message is not an error, and not helpful, remove it
  OMAP3: cpuidle: change the power domains modes determination logic
  OMAP3: cpuidle: code rework for improved readability
  OMAP3: cpuidle: re-organize the C-states data
  OMAP3: clean-up mach specific cpuidle data structures
  OMAP3 cpuidle: remove useless SDP specific timings
  usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
  usb: otg: OMAP4430: Fixing the omap4430_phy_init function
  usb: musb: am35x: fix compile error when building am35x
  usb: musb: OMAP4430: Power down the PHY during board init
  omap: drop board-igep0030.c
  omap: igep0020: add support for IGEP3
  omap: igep0020: minor refactoring
  omap: igep0020: name refactoring for future merge with IGEP3
  omap: Remove support for omap2evm
  arm: omap2plus: GPIO cleanup
  omap: musb: introduce default board config
  omap: move detection of NAND CS to common-board-devices
  omap: use common initialization for PMIC i2c bus
  omap: consolidate touch screen initialization among different boards
  ...

13 years agoMerge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Linus Torvalds [Thu, 26 May 2011 19:11:17 +0000 (12:11 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/4xx: Adding PCIe MSI support
  powerpc: Fix irq_free_virt by adjusting bounds before loop
  powerpc/irq: Protect irq_radix_revmap_lookup against irq_free_virt
  powerpc/irq: Check desc in handle_one_irq and expand generic_handle_irq
  powerpc/irq: Always free duplicate IRQ_LEGACY hosts
  powerpc/irq: Remove stale and misleading comment
  powerpc/cell: Rename ipi functions to match current abstractions
  powerpc/cell: Use common smp ipi actions
  Remove unused MSG_ flags in linux/smp.h
  powerpc/pseries: Update MAX_HCALL_OPCODE to reflect page coalescing
  powerpc/oprofile: Handle events that raise an exception without overflowing
  powerpc/ftrace: Implement raw syscall tracepoints on PowerPC

13 years agoFix build with !HUGETLBFS
Linus Torvalds [Thu, 26 May 2011 19:03:50 +0000 (12:03 -0700)]
Fix build with !HUGETLBFS

I stupidly broke the case of CONFIG_HUGETLBFS=n when doing the
conversion to vm_flags_t in commit ca16d140af91 ("mm: don't access
vm_flags as 'int'").  And my 'allyesconfig' build didn't find it, for
obvious reasons..

Include <linux/mm_types.h> in <linux/hugetlb.h>.  The problem could have
been avoided by just turning the hugetlb_file_setup() error wrapper into
a macro, but mm_types.h is a reasonable include in this file.

Reported-by: Richard -rw- Weinberger <richard.weinberger@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoMerge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec...
Linus Torvalds [Thu, 26 May 2011 17:55:15 +0000 (10:55 -0700)]
Merge branch 'linux-next' of git://git./linux/kernel/git/jlbec/ocfs2

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (28 commits)
  Ocfs2: Teach local-mounted ocfs2 to handle unwritten_extents correctly.
  ocfs2/dlm: Do not migrate resource to a node that is leaving the domain
  ocfs2/dlm: Add new dlm message DLM_BEGIN_EXIT_DOMAIN_MSG
  Ocfs2/move_extents: Set several trivial constraints for threshold.
  Ocfs2/move_extents: Let defrag handle partial extent moving.
  Ocfs2/move_extents: move/defrag extents within a certain range.
  Ocfs2/move_extents: helper to calculate the defraging length in one run.
  Ocfs2/move_extents: move entire/partial extent.
  Ocfs2/move_extents: helpers to update the group descriptor and global bitmap inode.
  Ocfs2/move_extents: helper to probe a proper region to move in an alloc group.
  Ocfs2/move_extents: helper to validate and adjust moving goal.
  Ocfs2/move_extents: find the victim alloc group, where the given #blk fits.
  Ocfs2/move_extents: defrag a range of extent.
  Ocfs2/move_extents: move a range of extent.
  Ocfs2/move_extents: lock allocators and reserve metadata blocks and data clusters for extents moving.
  Ocfs2/move_extents: Add basic framework and source files for extent moving.
  Ocfs2/move_extents: Adding new ioctl code 'OCFS2_IOC_MOVE_EXT' to ocfs2.
  Ocfs2/refcounttree: Publicize couple of funcs from refcounttree.c
  Ocfs2: Add a new code 'OCFS2_INFO_FREEFRAG' for o2info ioctl.
  Ocfs2: Add a new code 'OCFS2_INFO_FREEINODE' for o2info ioctl.
  ...

13 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djm/tmem
Linus Torvalds [Thu, 26 May 2011 17:50:56 +0000 (10:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/djm/tmem

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djm/tmem:
  xen: cleancache shim to Xen Transcendent Memory
  ocfs2: add cleancache support
  ext4: add cleancache support
  btrfs: add cleancache support
  ext3: add cleancache support
  mm/fs: add hooks to support cleancache
  mm: cleancache core ops functions and config
  fs: add field to superblock to support cleancache
  mm/fs: cleancache documentation

Fix up trivial conflict in fs/btrfs/extent_io.c due to includes

13 years agoMerge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
Linus Torvalds [Thu, 26 May 2011 17:49:11 +0000 (10:49 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: correctly decrement the extent buffer index in xfs_bmap_del_extent
  xfs: check for valid indices in xfs_iext_get_ext and xfs_iext_idx_to_irec
  xfs: fix up asserts in xfs_iflush_fork
  xfs: do not do pointer arithmetic on extent records
  xfs: do not use unchecked extent indices in xfs_bunmapi
  xfs: do not use unchecked extent indices in xfs_bmapi
  xfs: do not use unchecked extent indices in xfs_bmap_add_extent_*
  xfs: remove if_lastex
  xfs: remove the unused XFS_BMAPI_RSVBLOCKS flag
  xfs: do not discard alloc btree blocks
  xfs: add online discard support

13 years agoregulator: Fix 88pm8607.c printk format warning
Randy Dunlap [Thu, 26 May 2011 17:16:15 +0000 (10:16 -0700)]
regulator: Fix 88pm8607.c printk format warning

Fix printk format warning (seen on x86_64) and change to unsigned
output format:

drivers/regulator/88pm8607.c:417: warning: format '%d' expects type 'int', but argument 3 has type 'resource_size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agoinput: Add support for Qualcomm PMIC8XXX power key
Trilok Soni [Fri, 13 May 2011 09:47:51 +0000 (15:17 +0530)]
input: Add support for Qualcomm PMIC8XXX power key

Add support for PMIC8XXX power key driven over dedicated
KYPD_PWR_N pin.

Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agoinput: Add Qualcomm pm8xxx keypad controller driver
Trilok Soni [Thu, 19 May 2011 05:24:04 +0000 (10:54 +0530)]
input: Add Qualcomm pm8xxx keypad controller driver

Add Qualcomm PMIC8XXX based keypad controller driver
supporting upto 18x8 matrix configuration.

Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Add omap-usbhs runtime PM support
Keshava Munegowda [Sun, 22 May 2011 20:51:26 +0000 (22:51 +0200)]
mfd: Add omap-usbhs runtime PM support

The usbhs core driver does not enable/disable the interface and
functional clocks; These clocks are handled by hwmod and runtime pm,
hence insted of the clock enable/disable, the runtime pm APIS are
used. however,the port clocks and tll clocks are handled
by the usbhs core.

Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Fix ASIC3 SD Host Controller Configuration size
Paul Parsons [Sun, 15 May 2011 14:13:11 +0000 (14:13 +0000)]
mfd: Fix ASIC3 SD Host Controller Configuration size

The size of the TC6380AF SD Host Controller Configuration area is 0x200 bytes (assuming registers are aligned on 32-bit boundaries), not 0x400 bytes. Source: Toshiba TC6380AF Specification sections 4.2 and 4.3.1

Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Fix omap_usbhs_alloc_children error handling
Axel Lin [Sat, 14 May 2011 06:15:36 +0000 (14:15 +0800)]
mfd: Fix omap_usbhs_alloc_children error handling

1. Return proper error if omap_usbhs_alloc_child fails
2. In the case of goto err_ehci, we should call platform_device_unregister(ehci)
   instead of platform_device_put(ehci) because we have already added the
   platform device to device hierarchy.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Fix omap usbhs crash when rmmoding ehci or ohci
Keshava Munegowda [Mon, 16 May 2011 08:54:58 +0000 (14:24 +0530)]
mfd: Fix omap usbhs crash when rmmoding ehci or ohci

The disabling of clocks and freeing GPIO are changed
to fix the occurrence of the crash of rmmod of ehci and ohci
drivers. The GPIOs should be freed after the spin locks are
unlocked.

Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Add ASIC3 LED support
Paul Parsons [Fri, 13 May 2011 18:53:03 +0000 (18:53 +0000)]
mfd: Add ASIC3 LED support

Add LED support for the HTC ASIC3. Underlying support is provided by the mfd/asic3 and leds/leds-asic3 drivers. An example configuration is provided by the pxa/hx4700 platform.

Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agoleds: Add ASIC3 LED support
Paul Parsons [Fri, 13 May 2011 18:52:56 +0000 (18:52 +0000)]
leds: Add ASIC3 LED support

Add LED support for the HTC ASIC3. Underlying support is provided by the mfd/asic3 and leds/leds-asic3 drivers. An example configuration is provided by the pxa/hx4700 platform.

Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Update twl4030-code maintainer e-mail address
Peter Ujfalusi [Tue, 10 May 2011 05:59:23 +0000 (08:59 +0300)]
mfd: Update twl4030-code maintainer e-mail address

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
Johan Palsson [Sat, 7 May 2011 22:55:43 +0000 (00:55 +0200)]
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp

The bitmask for enabling the BatTemp pull-up was wrong and
is corrected. The name is also changed to be inline with
the AB8500 register description

Signed-off-by: Johan Palsson <johan.palsson@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
Karl Komierowski [Sat, 7 May 2011 22:55:31 +0000 (00:55 +0200)]
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0

In AB8500 3.0 the pull-up supplying the NTC must be manually activated.
Add enumerators to chip version detection logic.

Signed-off-by: Kalle Komierowski <karl.komierowski@stericsson.com>
Reviewed-by: Johan Palsson <johan.palsson@stericsson.com>
Reviewed-by: Daniel Willerud <daniel.willerud@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Provide ab8500-core enumerators for chip cuts
Linus Walleij [Sat, 7 May 2011 22:54:45 +0000 (00:54 +0200)]
mfd: Provide ab8500-core enumerators for chip cuts

Since functionality in MFD cells may need to be adjusted according to
chip revision, let's enumerate them and keep track of them.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Check twl4030-power remove script error condition after i2cwrite
Lesly A M [Wed, 4 May 2011 12:08:53 +0000 (17:38 +0530)]
mfd: Check twl4030-power remove script error condition after i2cwrite

Fixing the error condition check in twl4030 remove script function.
Due to some typo in commit ID: 11a441ce82d6ffecfd39b324024de0cd630b36c1

Signed-off-by: Lesly A M <leslyam@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Fix twl6030 irq definitions
Graeme Gregory [Thu, 12 May 2011 13:27:56 +0000 (14:27 +0100)]
mfd: Fix twl6030 irq definitions

The charger fault IRQs from the twl will in future patches be handled
by a seperate IRQ handler in the charger driver than the general charger
IRQ. Give them different IRQ numbers now to allow the charger driver to
be merged in the future.

Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Add phoenix lite (twl6025) support to twl6030
Graeme Gregory [Thu, 12 May 2011 13:27:55 +0000 (14:27 +0100)]
mfd: Add phoenix lite (twl6025) support to twl6030

Phoenix Lite is based on the twl6030 family of PMICs. It has mostly the
same feature set of twl6030 but with small changes. The codec block has
also been removed. It also has a new charger block and new features in
its ADC block. VUSB handling also differs.

Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Avoid to use constraint name in 88pm860x regulator driver
Haojian Zhuang [Fri, 6 May 2011 09:21:23 +0000 (17:21 +0800)]
mfd: Avoid to use constraint name in 88pm860x regulator driver

Avoid to use constraint name in regulator driver. So use regulator id is used
instead in platform driver.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Remove checking on max8925 regulator[0]
Haojian Zhuang [Fri, 6 May 2011 09:21:25 +0000 (17:21 +0800)]
mfd: Remove checking on max8925 regulator[0]

Since regulator[0] is always checking in mfd driver, it results in
registration failure without regulator[0].

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Remove unused parameter from 88pm860x API
Haojian Zhuang [Fri, 6 May 2011 09:21:24 +0000 (17:21 +0800)]
mfd: Remove unused parameter from 88pm860x API

i2c_client parameter isn't used in some functions. Just remove it.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Avoid to allocate 88pm860x static platform data
Haojian Zhuang [Fri, 6 May 2011 09:21:21 +0000 (17:21 +0800)]
mfd: Avoid to allocate 88pm860x static platform data

Maybe multiple PMIC devices are installed into one board. Static variable
can only make driver logic mess. So remove these variable, and use
platform data from platform driver instead.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Add rtc support to 88pm860x
Haojian Zhuang [Fri, 6 May 2011 09:21:20 +0000 (17:21 +0800)]
mfd: Add rtc support to 88pm860x

Enable rtc function in 88pm860x PMIC.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agoregulator: Enable max8925 i2c sequence for control
Haojian Zhuang [Mon, 18 Apr 2011 14:04:09 +0000 (22:04 +0800)]
regulator: Enable max8925 i2c sequence for control

Force to enable i2c as power up/down sequence. Otherwise, SD/LDO can't
be enabled or disabled via accessing i2c bus.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agopower_supply: Use max8925 platform_data from cell
Haojian Zhuang [Mon, 18 Apr 2011 14:04:08 +0000 (22:04 +0800)]
power_supply: Use max8925 platform_data from cell

Avoid to get platform_data from parent device. Get it from mfd cell
device instead.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Fix tps6586x GPIO value setting
Vincent Palatin [Tue, 12 Apr 2011 14:55:58 +0000 (10:55 -0400)]
mfd: Fix tps6586x GPIO value setting

In the current code, every time we set a TPS6586x GPIO pin,
the tps6586x_gpio_set function is resetting all other GPIO pins.
We need to update the right GPIOxOUT bit of the GPIOSET2 register instead
of overriding the full value.

Tested by setting sequentially GPIO2 and GPIO3 and verifying the
pins voltage.

Change-Id: I560edde146c5425cce37432c4ee91569eea5adcf
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agoMAINTAINERS: Add patterns for pmic 8921 files to MSM subsystem
Abhijeet Dharmapurikar [Tue, 5 Apr 2011 21:40:56 +0000 (14:40 -0700)]
MAINTAINERS: Add patterns for pmic 8921 files to MSM subsystem

Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
13 years agomfd: Add pm8xxx irq support
Abhijeet Dharmapurikar [Tue, 5 Apr 2011 21:40:53 +0000 (14:40 -0700)]
mfd: Add pm8xxx irq support

Add support for the irq controller in Qualcomm 8xxx pmic. The 8xxx
interrupt controller provides control for gpio and mpp configured as
interrupts in addition to other subdevice interrupts. The interrupt
controller also provides a way to read the real time status of an
interrupt. This real time status is the only way one can get the
input values of gpio and mpp lines.

Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>