libertas: Added callback functions to support SDIO suspend/resume.

In suspend() host sleep is activated using already configured
host sleep parameters through wol command, and in resume() host
sleep is cancelled. Earlier priv->fw_ready flag used to reset and
set in suspend and resume handler respectively. Since after suspend
only host goes into sleep state and firmware is always ready, those
changes in flag state are removed.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Add support for NVS files with 5GHz band parameters

This patch adds support for NVS files with 5GHz band parameters. The change
is done in a backward compatible manner - if 11a is not enabled in the driver,
the driver will allow also old NVS files to be loaded.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Update handling of the NVS file / INI parameters

This patch updates the handling of the NVS file INI-section, trying to make
it slightly more generic, and exposing the parameters being set. This is done
in preparation for 5GHz parameters.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Increase credit size

This is the maximum supported by the firmware.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Remove HW queue translation

There is no need to determine the HW queue
for each packet that is transmitted. The endpoint
can be chosen directly based on the queue type
that mac80211 sends down.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Initialize beacon/CAB queues

This patch initializes the beacon and CAB HW queues
when the driver is loaded.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add queue statistics to xmit debugfs file

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Enable Short GI in 20 Mhz for ar9287 and later chips

This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/orinoco: Use kzalloc

Use kzalloc rather than the combination of kmalloc and memset.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,size,flags;
statement S;
@@

-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
 if (x == NULL) S
-memset(x, 0, size);
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable the baseband watchdog events for AR9003

This enables the baseband watchdog events for the AR9003
family on ath9k. Upon an a baseband watchdog interrupt we reset
the hardware, this should address corner case conditions where
normal operation can stall. Enable ATH_DBG_RESET to be able
to review details of the bb watchdog interrupt once it happens.
If you're curious how often this happens just grep the debugfs
interrupt file.

Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add support for the AR9003 baseband watchdog

The baseband watchdog will monitor blocks of the baseband
through timers and will issue an interrupt when things are
detected to be stalled. It is only available on the AR9003
family.

Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add the minstrel_ht rate control algorithm

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move rt2x00debug_dump_frame declaration to rt2x00.h.

This allows rt2x00debug_dump_frame to be used from everywhere.

This is preparation for beacon writing clean ups.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: remove sdio ARM dependency

Make it possible to use wl1271's SDIO interface on non-ARM platforms.

Fully tested on a x86 platform, compile-tested on ARM.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: rename the ar9003_initvals.h to ar9003_2p0_initvals.h

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add support for the AR9003 2.2

The checksums of the initvals are:

initvals -f ar9003-2p2
0x00000000c2bfa7d5        ar9300_2p2_radio_postamble
0x00000000ada2b114        ar9300Modes_lowest_ob_db_tx_gain_table_2p2
0x00000000e0bc2c84        ar9300Modes_fast_clock_2p2
0x00000000056eaf74        ar9300_2p2_radio_core
0x0000000000000000        ar9300Common_rx_gain_table_merlin_2p2
0x0000000078658fb5        ar9300_2p2_mac_postamble
0x0000000023235333        ar9300_2p2_soc_postamble
0x0000000054d41904        ar9200_merlin_2p2_radio_core
0x000000008475a084        ar9300_2p2_baseband_postamble
0x000000009aaafd90        ar9300_2p2_baseband_core
0x000000003df9a326        ar9300Modes_high_power_tx_gain_table_2p2
0x000000001cfba124        ar9300Modes_high_ob_db_tx_gain_table_2p2
0x0000000011302700        ar9300Common_rx_gain_table_2p2
0x00000000a9a2b114        ar9300Modes_low_ob_db_tx_gain_table_2p2
0x00000000a9d66d40        ar9300_2p2_mac_core
0x000000001e1d0800        ar9300Common_wo_xlna_rx_gain_table_2p2
0x00000000a0c531c8        ar9300_2p2_soc_preamble
0x00000000292e2544        ar9300PciePhy_pll_on_clkreq_disable_L1_2p2
0x000000002d3e2544        ar9300PciePhy_clkreq_enable_L1_2p2
0x00000000293e2544        ar9300PciePhy_clkreq_disable_L1_2p2

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: use the dma state API instead of the pci equivalents

The DMA API is preferred.

No functional change.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

ssb: fix NULL ptr deref when pcihost_wrapper is used

Ethernet driver b44 does register ssb by it's pcihost_wrapper
and doesn't set ssb_chipcommon. A check on this value
introduced with commit d53cdbb94a52a920d5420ed64d986c3523a56743
and ea2db495f92ad2cf3301623e60cb95b4062bc484 triggers:

BUG: unable to handle kernel NULL pointer dereference at 00000010
IP: [<c1266c36>] ssb_is_sprom_available+0x16/0x30

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: make a function static

sparse correctly complains that
__ieee80211_get_channel_mode is not static.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix uninitialized variable warning

Fixes:

drivers/net/wireless/libertas/rx.c: In function process_rxed_802_11_packet:
drivers/net/wireless/libertas/rx.c:354: error: radiotap_hdr.flags may be used uninitialized in this function

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix bug in the way "bf_tx_aborted" of struct ath_buf is used

This bug was introduced by the following commit

Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date:   Thu Apr 15 17:38:46 2010 -0400

ath9k: Remove ATH9K_TX_SW_ABORTED and introduce a bool for this purpose

Wrong buffer is checked for bf_tx_aborted field in ath_tx_num_badfrms(),
this may result in a rate scaling with wrong feedback (number
of unacked frames in this case). It is the last one in the chain
of buffers for an aggregate frame that should be checked.

Also it misses the initialization of this field in the buffer,
this may lead to a situation where we stop the sw retransmission
of failed subframes associated to this buffer.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix ath_print in xmit for hardware reset.

ath_print in xmit.c should say "Reseting hardware"
instead of Resetting HAL!(since HAL is being fazed out).
dmesg shows:
[ 8660.899624] ath: Failed to stop TX DMA in 100 msec after killing last frame
[ 8660.899676] ath: Unable to stop TxDMA. Reset HAL!

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170usb: fix read from freed driver context

Commit "ar9170: wait for asynchronous firmware loading"
introduced a bug, which is triggered by fatal errors
while the driver is initializing the device.

BUG: unable to handle kernel paging request at 6b6b6bf7
IP: [<c117b567>] kobject_put+0x7/0x70
*pde = 00000000
Oops: 0000 [#1] PREEMPT
last sysfs file: /sys/devices/platform/hdaps/position
Modules linked in: ar9170usb [...]

Pid: 6246, comm: firmware/ar9170 Not tainted 2.6.34-wl #54
EIP: 0060:[<c117b567>] EFLAGS: 00010206 CPU: 0
EIP is at kobject_put+0x7/0x70
EAX: 6b6b6bd7 EBX: f4d3d0e0 ECX: f5ba9124 EDX: f6af2a7c
ESI: 00000000 EDI: f4d3d0e0 EBP: 00000000 ESP: f5e98f9c
 DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process firmware/ar9170 (pid: 6246)
Stack:
 c12532ed 00000246 f5bfaa70 f8487353 f4d3d0e0
Call Trace:
 [<c12532ed>] ? device_release_driver+0x1d/0x30
 [<f8487353>] ? ar9170_usb_firmware_failed+0x43/0x70 [ar9170usb]
 [<c125983c>] ? request_firmware_work_func+0x2c/0x70
 [<c1259810>] ? request_firmware_work_func+0x0/0x70
 [<c10413f4>] ? kthread+0x74/0x80
 [<c1041380>] ? kthread+0x0/0x80
 [<c1003136>] ? kernel_thread_helper+0x6/0x10
Code: 40 d3 f2 ff 85 c0 89 c3 74 0a ba 44 86 4c c1 e8 [...]
EIP: [<c117b567>] kobject_put+0x7/0x70 SS:ESP 0068:f5e98f9c
CR2: 000000006b6b6bf7
---[ end trace e81abb992434b410 ]---

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "rt2x00: Fix rt2800usb TX descriptor writing."

This reverts commit 663cb47cc2c5acd32850f67d051e47d62ed199c9.

This patch was merged out of the proper order, so instead of fixing a
problem with a prior (unmerged) patch, it creates one.  Ooops!

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove VEOL support for ad-hoc

With VEOL, Beacon transmission in ad-hoc does not currently work.
I believe for larger ad-hoc networks, VEOL is too unreliable, as
it can get beacon transmissions stuck during synchronization.
Use SWBA based beacon trasmission similar to AP mode instead.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: change beacon allocation to prefer the first beacon slot

This fixes IBSS beacon transmissions without VEOL enabled

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep

The functionality to keep the device awake until it is done with
the rx of any mcast/bcast frames which are pending on AP should
also be added to the hardwares which support auto sleep feature.
This patch fixes frequent failures in ARP resolution when it is
initiated by the other end. Currently auto sleep is enabled only
for ar9003 in ath9k.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: fix sta_info.h kernel-doc warnings

Fix sta_info.h kernel-doc warnings:

Warning(net/mac80211/sta_info.h:164): No description found for parameter 'tid_active_rx[STA_TID_NUM]'
Warning(net/mac80211/sta_info.h:164): Excess struct/union/enum/typedef member 'tid_state_rx' description in 'sta_ampdu_mlme'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: fix mac80211.h kernel-doc warnings

Fix kernel-doc warnings in mac80211.h:

Warning(include/net/mac80211.h:838): No description found for parameter 'ap_addr'
Warning(include/net/mac80211.h:1726): No description found for parameter 'get_survey'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: testing the wrong variable in iwl_add_bssid_station()

The intent here is to test that "sta_id_r" is a valid pointer.  We do
this same test later on in the function.

Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()

This is obviously a small picky thing.  The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: dereferencing before check in hif_usb_tx_cb()

After c11d8f89d3b7: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix rt2800usb TX descriptor writing.

The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.

(Based on a patch created by Ondrej Zary)

In some circumstances the Ralink devices do not properly go to sleep
or wake up, with timeouts occurring.
Fix this by retrying telling the device that it has to wake up or
sleep.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "ath9k: Group Key fix for VAPs"

This reverts commit 03ceedea972a82d343fa5c2528b3952fa9e615d5.

This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: update gfp/slab.h includes

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: don't use to_pci_dev in rt2x00pci_uninitialize

Don't use to_pci_dev in rt2x00pci_uninitialize to get the allocated irq
as it won't work for platform devices (SoC). Instead, use the irq field
that's already used everywhere else.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: consistently use rx_bufsize for RX DMA

We should use the same buffer size we set up for DMA also in the hardware
descriptor. Previously we used common->rx_bufsize for setting up the DMA
mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the
descriptor itself. The problem is that skb_tailroom(skb) can give us a larger
value than the size we set up for DMA before. This allows the hardware to write
into memory locations not set up for DMA. In practice this should rarely happen
because all packets should be smaller than the maximum 802.11 packet size.

On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559
bytes length (including padding for cache alignment) but sbk_tailroom() was
2592. Just consistently use rx_bufsize for all RX DMA memory sizes.

Also use the return value of the descriptor setup function.

Cc: stable@kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add missing braces

Specifying a valid channel type will get
goto out rather than continuing, due to
missing braces. This affects both remain
on channel and action frame TX commands.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: replace wireless_send_event with cfg80211_disconnected

Remove (hopefully) last use of WEXT in rndis_wlan. Replace wireless_send_event
with missing cfg80211_disconnected in rndis_wlan_do_link_down_work.

Reported-by: "Rogério Brito" <rbrito@ime.usp.br>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove AR9003 from PCI IDs for now

We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.

Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix crash in cfg80211_set_freq()

Since wdev can be NULL, check it before dereferencing it

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: Fix RX data path frame lengths

The current frame length used by the driver for RX frames is the SPI bus
transfer length. This length has padding bytes, which do not belong to the
WLAN frame.

As there is no other length information in the WLAN frame except the skb
length this problem caused for instance extra ESSID's to be listed at the
end of scan results (IE id 0) with zero length.

Fix the frame length by removing padding.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix internal scan race

It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.

Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
  triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
 failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
  and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
   place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
  there is some locking missing around the "is_internal_short_scan"
  variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
   scan and thus causes problems with wrong memory being accessed.

The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
  scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Fix signal_type comparison

signal_type is enum cfg80211_signal_type.

This fixes the gcc warning:

scan.c: In function `cfg80211_inform_bss':
scan.c:518:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'
scan.c: In function `cfg80211_inform_bss_frame':
scan.c:574:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: fix problem in dequeuing from input_pkt_queue

Fix some issues introduced in batch skb dequeuing for input_pkt_queue.
The primary issue it that the queue head must be incremented only
after a packet has been processed, that is only after
__netif_receive_skb has been called.  This is needed for the mechanism
to prevent OOO packet in RFS.  Also when flushing the input_pkt_queue
and process_queue, the process queue should be done first to prevent
OOO packets.

Because the input_pkt_queue has been effectively split into two queues,
the calculation of the tail ptr is no longer correct.  The correct value
would be head+input_pkt_queue->len+process_queue->len.  To avoid
this calculation we added an explict input_queue_tail in softnet_data.
The tail value is simply incremented when queuing to input_pkt_queue.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

can: SJA1000 add missing spin_lock_init()

As remarked by Sam Ravnborg the spin_lock variable, that has been introduced
in commit 57c8a456640fa3ca777652f11f2db4179a3e66b6 ("can: Fix SJA1000 command
register writes on SMP systems") has not been initialized properly.

This patch adds the initialization to allow spinlock debugging.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sh_eth: Fix memleak in sh_mdio_release

Allocated memory for IRQs should be freed when releasing the mii_bus

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-next-2.6

gro: Fix bogus gso_size on the first fraglist entry

When GRO produces fraglist entries, and the resulting skb hits
an interface that is incapable of TSO but capable of FRAGLIST,
we end up producing a bogus packet with gso_size non-zero.

This was reported in the field with older versions of KVM that
did not set the TSO bits on tuntap.

This patch fixes that.

Reported-by: Igor Zhang <yugzhang@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe:add support for a new 82599 10G Base-T device

This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/gregkh/usb-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
  USB: remove unused usb_buffer_alloc and usb_buffer_free macros
  usb: musb: update gfp/slab.h includes
  USB: ftdi_sio: fix legacy SIO-device header
  USB: kl5usb105: reimplement using generic framework
  USB: kl5usb105: minor clean ups
  USB: kl5usb105: fix memory leak
  USB: io_ti: use kfifo to implement write buffering
  USB: io_ti: remove unsused private counter
  USB: ti_usb: use kfifo to implement write buffering
  USB: ir-usb: fix incorrect write-buffer length
  USB: aircable: fix incorrect write-buffer length
  USB: safe_serial: straighten out read processing
  USB: safe_serial: reimplement read using generic framework
  USB: safe_serial: reimplement write using generic framework
  usb-storage: always print quirks
  USB: usb-storage: trivial debug improvements
  USB: oti6858: use port write fifo
  USB: oti6858: use kfifo to implement write buffering
  USB: cypress_m8: use kfifo to implement write buffering
  USB: cypress_m8: remove unused drain define
  ...

Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c

sound: fixup for usb_buffer_alloc/free rename

This is needed before the USB merge.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c

Merge branch 'docs-next' of git://git.lwn.net/linux-2.6

* 'docs-next' of git://git.lwn.net/linux-2.6:
  Add a document describing the padata interface

Merge branch 'viafb-next' of git://git.lwn.net/linux-2.6

* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
  viafb: move some include files to include/linux
  viafb: Eliminate some global.h references
  viafb: get rid of i2c debug cruft
  viafb: fold via_io.h into via-core.h
  viafb: Fix initialization error paths
  viafb: Do not remove gpiochip under spinlock
  viafb: make procfs entries optional
  viafb: fix proc entry removal
  viafb: improve misc register handling
  viafb: replace inb/outb
  viafb: move some modesetting functions to a seperate file
  viafb: unify modesetting functions
  viafb: Reserve framebuffer memory for the upcoming camera driver
  viafb: Add a simple VX855 DMA engine driver
  viafb: Add a simple interrupt management infrastructure
  via: Rationalize vt1636 detection
  viafb: Introduce viafb_find_i2c_adapter()
  via: Do not attempt I/O on inactive I2C adapters
  viafb: Turn GPIO and i2c into proper platform devices
  viafb: Convert GPIO and i2c to the new indexed port ops
  ...

USB: remove unused usb_buffer_alloc and usb_buffer_free macros

Now that all callers are converted over, remove the compatibility
functions and all is good.

Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb: musb: update gfp/slab.h includes

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: ftdi_sio: fix legacy SIO-device header

Length field of header was incorrectly set to available payload space
rather than the actual payload size.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: kl5usb105: reimplement using generic framework

Kill custom read and write implementations (static per-port,
singleton(!) urb pool).

Also remove changelog header (can be retrieved through git).

Read processing and write-buffer handling tested using a cp210x device
in a loopback setup.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: kl5usb105: minor clean ups

Whitespace changes and some removed comments.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: kl5usb105: fix memory leak

Private data was not freed on error path in startup.

Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: io_ti: use kfifo to implement write buffering

Kill custom fifo implementation.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: io_ti: remove unsused private counter

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: ti_usb: use kfifo to implement write buffering

Kill custom fifo implementation.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: ir-usb: fix incorrect write-buffer length

Returned length should include header length.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: aircable: fix incorrect write-buffer length

Returned length should include header length.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: safe_serial: straighten out read processing

Clean up read processing logic.

Tested using a cp210x device in a loopback setup.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: safe_serial: reimplement read using generic framework

Use process_read_urb to implement read processing.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: safe_serial: reimplement write using generic framework

Kill custom single-urb write implementation.

Note that this driver still depended on the write callback from the old
generic framework.

Tested against original read processing using a cp210x device in a
loopback setup.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb-storage: always print quirks

Right now quirks are printed only when the are manually overriden with
the module parameters. It's not so useful to remind the user that his
parameters are correctly applied; what is useful is to print out the
quirks the user is not aware are being applied.

So let's do the smart thing and print the quirks when they are present.

Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: usb-storage: trivial debug improvements

Use pr_foo and dev_foo instead of printk. Maybe US_DEBUG* should be
replaced too.

Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: oti6858: use port write fifo

Kill private write fifo and use port fifo instead (protected under
port lock).

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: oti6858: use kfifo to implement write buffering

Kill custom fifo implementation.

Use private write fifo to minimise changes to lock handling.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: cypress_m8: use kfifo to implement write buffering

Kill custom fifo implementation.

Note that cypress_m8 has no port write fifo as it has no bulk-out
endpoint.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: cypress_m8: remove unused drain define

Driver uses tty-port drain these days.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: usb_debug: set bulk out size at probe

Use bulk_out_size in usb_serial_driver to set urb buffer size.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: gadget: Use kmemdup

Use kmemdup when some other buffer is immediately copied into the
allocated region.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
statement S;
@@

-  to = \(kmalloc\|kzalloc\)(size,flag);
+  to = kmemdup(from,size,flag);
   if (to==NULL || ...) S
-  memcpy(to, from, size);
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: CP210x New Device IDs 11 New device IDs

Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: visor: increase bulk-out buffer size

Increase the bulk-out buffer size to avoid any regression in throughput
after replacing the old writing scheme which used dynamic buffers (e.g.
up to 2k).

256b has been determined to be a good choice for several drivers
including ftdi_sio which used to have a more or less identical write
implementation.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: belkin_sa: implement line status handling

Use process_read_urb to implement line status handling.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: belkin_sa: clean up open

Use generic open to submit read urb.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: belkin_sa: minor clean-ups

Remove some whitepace and comments.
Clean up close.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: cp210x: use generic open to start reading from device

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: visor: reimplement using generic framework

Kill custom read and write implementations (dynamically allocated write
urbs).

Note that I chose to remove the stat module parameter which was supposed
to keep count of the amount of data sent and received, but which has
been broken for three years (since b308e74d9c708ee2a9af14fbe235e0a41216f4ed
"USB: visor driver adapted to new tty buffering" -- bytes_in was
incorrectly updated and was thus always reported as 0).

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: visor: fix memory leak

Fix memory leak for some devices (Sony Clie 3.5) due to port private
data not being freed on release.

Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: spcp8x5: reimplement using generic framework

Kill custom fifo, read, and single-urb write implementations.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: ipaq: reimplement using generic framework

Kill custom fifo, read and write implementations (single-urb and fifo,
but still maintained list of 256*256b urb buffers per port).

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: empeg: reimplement using generic framework

Kill custom read and write implementations (static 16*4k write-urb pool
shared among all ports in system).

Also remove old changelog entries in header (code is now gone, and
these entries can still be retrieved through git).

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: serial: add special case for processing of empty read urbs

Return immediately from generic process_read_urb if urb is empty.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: kobil: fix memory leak

An urb transfer buffer is allocated at every open but was never freed.

This driver is a bit of a mess...

Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: option.c: OLIVETTI OLICARD100 support

This patch adds support for an olivetti olicard100 HЅDPA usb-stick.

This device is a zeroCD one with ID 0b3c:c700 that needs switching via
eject or usb-modeswitch with
MessageContent="5553424312345678000000000000061b000000030000000000000000000000".
After switching it has ID 0b3c:c000 and provides 5 serial ports ttyUSB[0-4].
Port 0 (modem) and 4 are interrupt ports.

Signed-off-by: Nils Radtke <lkml@Think-Future.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: xhci: fix compiler warning.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: remove match_device

usb_find_device was the only one user of match_device, now
it is removed, so remove match_device to fix the compile warning
below reported by Stephen Rothwell:

drivers/usb/core/usb.c:596: warning: 'match_device'
defined but not used

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: include/usb/*.h checkpatch cleanup

Lots of minor formatting cleanups in includes/usb/ to make checkpatch
happier.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: usb.h: checkpatch cleanups

Minor formatting changes to clean up the file.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: visor.h: checkpatch cleanups

Minor whitespace cleanups to make checkpatch happy.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: pl2303.h: checkpatch cleanups

Minor whitespace cleanups to make checkpatch happy.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: kobil_sct.h: checkpatch cleanups

Minor whitespace cleanups to make checkpatch happy.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>