GitHub/LineageOS/G12/android_kernel_amlogic_linux-4.9.git
12 years agowlcore: update beacon and probe_resp templates when rates change
Luciano Coelho [Thu, 10 May 2012 09:14:04 +0000 (12:14 +0300)]
wlcore: update beacon and probe_resp templates when rates change

When the data rates change, we get BSS_CHANGED_BASIC_RATES.  At this
point, we should update all the templates to match the new rates.  We
were changing some of the templates, but the beacon and the probe
response templates were missing.

[Remove redundant min_rate variable - Arik]

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: disable MCS_13 for wl18xx PG 1.0
Luciano Coelho [Thu, 10 May 2012 09:14:03 +0000 (12:14 +0300)]
wl18xx: disable MCS_13 for wl18xx PG 1.0

There are some problems with MCS_13 in PG 1.0 hardware.  So we disable
it when PG 1.0 is detected.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore: reorder identify_chip and get_hw_info
Luciano Coelho [Thu, 10 May 2012 09:14:02 +0000 (12:14 +0300)]
wlcore: reorder identify_chip and get_hw_info

We can do get the HW information and identify the chip already at
probe time.  This makes it easier to mangle with the parameters during
identify chip before registering the hardware with mac80211.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: change low_band_component_type value for COM8
Luciano Coelho [Thu, 10 May 2012 09:14:01 +0000 (12:14 +0300)]
wl18xx: change low_band_component_type value for COM8

Like HDK, COM8 uses 0x06 for the low_band_component_type as well.
Hardcode the value for COM8 until this configuration can be done in
the external configuration binary (to be implemented).

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore: add space for private area when allocating fw_status
Luciano Coelho [Thu, 10 May 2012 09:14:00 +0000 (12:14 +0300)]
wlcore: add space for private area when allocating fw_status

When allocating the fw_status structure, the space for the
lower-driver private area was missing.  This was causing an illegal
write outside the allocated area, which was causing random oopses
around the kernel.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: changed default board_type to HDK
Luciano Coelho [Thu, 10 May 2012 09:13:59 +0000 (12:13 +0300)]
wl18xx: changed default board_type to HDK

Since the most common board we're using now is an HDK board, change
the default board_type to hdk.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: copy the default configuration before checking the board_type
Luciano Coelho [Thu, 10 May 2012 09:13:58 +0000 (12:13 +0300)]
wl18xx: copy the default configuration before checking the board_type

We were changing the low_band_component_type in the private
configuration structure before copying the default values to it, so
the change was overwritten and only took effect after HW recovery.

Reported-by: Dror Erez <drorer@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore: add module parameter to dump SDIO reads and writes
Luciano Coelho [Thu, 10 May 2012 09:13:57 +0000 (12:13 +0300)]
wlcore: add module parameter to dump SDIO reads and writes

In some cases we may want to dump all the SDIO data in order to get
detailed information for debugging the communication with the
firmware.

Add printks to dump the data and a module parameter to enable/disable
it.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add a module parameter to control 11a support
Luciano Coelho [Thu, 10 May 2012 09:13:56 +0000 (12:13 +0300)]
wl18xx: add a module parameter to control 11a support

In wl18xx we don't have an NVS yet, so we need to control whether 11a
is supported with a module parameter for now.  11a support is enabled
by default and can be changed by setting enable_11a to false when
loading the module.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: derive the MAC address from the BD_ADDR in fuse ROM
Luciano Coelho [Thu, 10 May 2012 09:13:55 +0000 (12:13 +0300)]
wl18xx: derive the MAC address from the BD_ADDR in fuse ROM

Add the get_mac operation in order to fetch the BD_ADDR from fuse ROM,
so that we can derive the WLAN MAC addresses from it.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore/wl12xx/18xx: split fw_status struct into two
Arik Nemtsov [Thu, 10 May 2012 09:13:54 +0000 (12:13 +0300)]
wlcore/wl12xx/18xx: split fw_status struct into two

The number of RX packet descriptors may vary from chip to chip and
in different firmware versions.  Unfortunately, the array that
contains the actual descriptors is in the middle of the fw_status
structure.  To manage this, we split the struct into two so we can
calculate the offset of what comes after the array and access the last
elements more easily.

[Changed the STATUS_LEN macro to be placement agnostic - Arik]

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add module parameter to disable TCP checksum
Luciano Coelho [Thu, 10 May 2012 09:13:53 +0000 (12:13 +0300)]
wl18xx: add module parameter to disable TCP checksum

Add a new module parameter to disable TCP checksum offload.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add number of antennas and dc2dc type as module params
Luciano Coelho [Thu, 10 May 2012 09:13:52 +0000 (12:13 +0300)]
wl18xx: add number of antennas and dc2dc type as module params

We need to specify the number of 2.4GHz and 5GHz antennas and whether
the board has an internal or external DC2DC.  Add some module
parameters that allow changing that.

In the future this will come from the "NVS" file.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: change the low_band_component_type for HDK boards
Luciano Coelho [Thu, 10 May 2012 09:13:51 +0000 (12:13 +0300)]
wl18xx: change the low_band_component_type for HDK boards

Currently, all HDK boards use low_band_component_type 0x06.  In the
future this may change, but for now, we hardcode this value when the
board_type is set to HDK.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add plt_init operation
Luciano Coelho [Thu, 10 May 2012 09:13:50 +0000 (12:13 +0300)]
wl18xx: add plt_init operation

Add the correct FW name for PLT (which is the same as the normal
firmware) and implement the plt_init operation.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore/wl12xx: add plt_init op and move the code to wl12xx
Luciano Coelho [Thu, 10 May 2012 09:13:49 +0000 (12:13 +0300)]
wlcore/wl12xx: add plt_init op and move the code to wl12xx

PLT mode needs to be initialized differently for each chip.  This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: change board type enum according to new FW
Arik Nemtsov [Thu, 10 May 2012 09:13:48 +0000 (12:13 +0300)]
wl18xx: change board type enum according to new FW

Add more board types and remove a now unneeded write to SCR_PAD2 setting
the board type.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: don't upload NVS to FW
Arik Nemtsov [Thu, 10 May 2012 09:13:47 +0000 (12:13 +0300)]
wl18xx: don't upload NVS to FW

In this chip family the NVS file should not be uploaded to FW. In fact,
we encounter strange bugs (sdio errors) when trying to upload it with
certain parameters.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: init Tx-released index to 0 on HW init
Arik Nemtsov [Thu, 10 May 2012 09:13:46 +0000 (12:13 +0300)]
wl18xx: init Tx-released index to 0 on HW init

This ensures the index is 0 on FW recovery and prevents spurious error
prints - "WARNING illegal id in tx completion".

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore/wl12xx: move rx_mem_pool_addr element to wl12xx
Luciano Coelho [Thu, 10 May 2012 09:13:45 +0000 (12:13 +0300)]
wlcore/wl12xx: move rx_mem_pool_addr element to wl12xx

Only wl127x chips use the rx_mem_pool_addr values, which need to be
given to the firmware as part of the RX path.  Move this from core to
the wl12xx driver.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: implement hw op to read PG version
Arik Nemtsov [Thu, 10 May 2012 09:13:44 +0000 (12:13 +0300)]
wl18xx: implement hw op to read PG version

Read the HW PG version of the 18xx chip from FUSE.

Based on an earlier patch by Luciano Coelho <coelho@ti.com>.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore/wl12xx: move ref_clock and tcxo_clock elements to wl12xx
Luciano Coelho [Thu, 10 May 2012 09:13:43 +0000 (12:13 +0300)]
wlcore/wl12xx: move ref_clock and tcxo_clock elements to wl12xx

Only wl12xx needs to get the ref_clock anc tcxo_clock values from the
platform data.  Move these elements from the wl1271 structure to
wl12xx's private data.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore: rename wl12xx.h to wlcore_i.h
Luciano Coelho [Thu, 10 May 2012 09:13:42 +0000 (12:13 +0300)]
wlcore: rename wl12xx.h to wlcore_i.h

The wl12xx.h file now contains mostly definitions that are internal to
wlcore.  Still, some things need to me moved to the public header, so
for now we keep including it in wlcore.h.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: read clock frequency and do top init accordingly
Luciano Coelho [Thu, 10 May 2012 09:13:41 +0000 (12:13 +0300)]
wl18xx: read clock frequency and do top init accordingly

Instead of using hardcoded values for a single frequency, we need to
read the frequency and use the appropriate values for it in the top
initialization.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: disable FW log functionality
Arik Nemtsov [Thu, 10 May 2012 09:13:40 +0000 (12:13 +0300)]
wl18xx: disable FW log functionality

Currently (Fw .67) appears to do more harm than good.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: read FW pc on recovery
Arik Nemtsov [Thu, 10 May 2012 09:13:39 +0000 (12:13 +0300)]
wl18xx: read FW pc on recovery

Define the FW pc in the 18xx register translation table. This specific
register is only valid in the boot partition, so change the momentarily
change partitions. This doesn't damage 12xx cards, where the FW pc is
accessible via boot partition as well.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: translate and write the board type to SCR_PAD2
Luciano Coelho [Thu, 10 May 2012 09:13:38 +0000 (12:13 +0300)]
wl18xx: translate and write the board type to SCR_PAD2

The firmware uses the SCR_PAD2 register to read the board type passed
from the driver.  The values don't match the ones used in the mac and
phy configuration, so we need to map them before writing.  This commit
adds a translation table that is used when writing the board type to
SCR_PAD2.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add board type module argument
Luciano Coelho [Thu, 10 May 2012 09:13:37 +0000 (12:13 +0300)]
wl18xx: add board type module argument

Different board types (ie. FPGA, HDK and DVP/EVB) require slightly
different init configuration options.  Since we cannot probe the type
of board from the actual hardware, we need to pass it as an option
during module load.

This patch adds a module parameters that accepts the 3 different board
types, with DVP/EVB as the default, and uses this value where needed.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add module param for overriding HT caps
Arik Nemtsov [Thu, 10 May 2012 09:13:36 +0000 (12:13 +0300)]
wl18xx: add module param for overriding HT caps

Set an alternate HT cap allowing MIMO rates (but only 20mhz) channels,
when the module is loaded with ht_mode=mimo.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: set HT capabilities
Arik Nemtsov [Thu, 10 May 2012 09:13:35 +0000 (12:13 +0300)]
wl18xx: set HT capabilities

Define the default HT capabilities of the 18xx chip family - these include
support for wide-channel.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore/wl18xx: enable MIMO/wide-chan rates in AP-mode rate config
Arik Nemtsov [Thu, 10 May 2012 09:13:34 +0000 (12:13 +0300)]
wlcore/wl18xx: enable MIMO/wide-chan rates in AP-mode rate config

Add a HW op to add extra enabled rates for AP-mode data-rates. Since
the rates might depend on channel properties, reconfigure AP-mode rates
when these change.

Implement the HW op for the 18xx family, where MIMO or wide-chan rates
can be added.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: support peer MIMO rates
Arik Nemtsov [Thu, 10 May 2012 09:13:33 +0000 (12:13 +0300)]
wlcore: support peer MIMO rates

Parse the peer ht_cap element containing MCS8-MCS15 rates and pass it
to the FW. Rates unsupported by the HW will be sanitized by mac80211
before reaching us.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: ipmlement ap_rate_mask hw op
Arik Nemtsov [Thu, 10 May 2012 09:13:32 +0000 (12:13 +0300)]
wl18xx: ipmlement ap_rate_mask hw op

Enable wide-chan or MIMO rates when appropriate.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: send channel type to FW on role start
Arik Nemtsov [Thu, 10 May 2012 09:13:31 +0000 (12:13 +0300)]
wl18xx: send channel type to FW on role start

Translate the NL80211 channel type to a FW-specific channel type and send
it to the FW as part of the role-start command. For wl12xx this has no
effect - this element is treated as padding.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: track current channel type per vif
Arik Nemtsov [Thu, 10 May 2012 09:13:30 +0000 (12:13 +0300)]
wlcore: track current channel type per vif

Track the current 802.11 channel type, defaulting to a NO_HT channel.
Update the channel type element when changed by mac80211.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: add runtime configuration parameters
Luciano Coelho [Thu, 10 May 2012 09:13:29 +0000 (12:13 +0300)]
wl18xx: add runtime configuration parameters

Now wlcore requires the lower drivers to set the correct
configuration.  Move the existing private configuration to the proper
place and add all generic configuration parameters.

The important changes are in Tx interrupt pacing and Rx BA window size.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore/wl18xx: add hw op for Rx HW checksum
Arik Nemtsov [Thu, 10 May 2012 09:13:28 +0000 (12:13 +0300)]
wlcore/wl18xx: add hw op for Rx HW checksum

Some chip families can checksum certain classes of Rx packets in FW.
Implement the Rx-checksum feature as a HW-op. For the 18xx chip-family,
set Rx-checsum according to indication from FW.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore/wl18xx: add hw op for setting Tx HW checksum
Arik Nemtsov [Thu, 10 May 2012 09:13:27 +0000 (12:13 +0300)]
wlcore/wl18xx: add hw op for setting Tx HW checksum

Some chip families are capable of checksumming certain classes of Tx
packets in HW. Indicate this fact in the netdev features and perform the
HW checksum by protocol type for the 18xx family.

Fix the location of the skb network header when we move it so we can
rely on it when setting the checksum.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: add hw_init operation
Luciano Coelho [Thu, 10 May 2012 09:13:26 +0000 (12:13 +0300)]
wl18xx: add hw_init operation

Add wl18xx-specific HW initialization operation and create acx.[ch]
files to support that.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: implement immediate Tx completion
Arik Nemtsov [Thu, 10 May 2012 09:13:25 +0000 (12:13 +0300)]
wl18xx: implement immediate Tx completion

Implement immediate Tx completion for the 18xx family. Move 18xx
specific Tx code to new tx.c/h files and create helper header files
for definitions.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: implement hw op for getting rx packet data length
Arik Nemtsov [Thu, 10 May 2012 09:13:24 +0000 (12:13 +0300)]
wl18xx: implement hw op for getting rx packet data length

Implement the 18xx-specific way for getting the length of a Rx packet.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: implement hw op for getting rx buffer data alignment
Arik Nemtsov [Thu, 10 May 2012 09:13:23 +0000 (12:13 +0300)]
wl18xx: implement hw op for getting rx buffer data alignment

Implement the HW op for getting alignment state in wl18xx. The FW aligns
the Rx Ethernet payload data.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: set Rx block-size alignment quirk
Arik Nemtsov [Thu, 10 May 2012 09:13:22 +0000 (12:13 +0300)]
wl18xx: set Rx block-size alignment quirk

The 18xx FW sends Rx blocks with aligned length.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: add fw_status private data
Arik Nemtsov [Thu, 10 May 2012 09:13:21 +0000 (12:13 +0300)]
wl18xx: add fw_status private data

The wl18xx chip passes extra information in the firmware status to the
driver.  Add a private data section to handle that.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: define HW-rate translation elements/tables
Arik Nemtsov [Thu, 10 May 2012 09:13:20 +0000 (12:13 +0300)]
wl18xx: define HW-rate translation elements/tables

Define HW-rate conversion tables for the 18xx chip. Initialize
the appropriate wlcore elements with these tables and values to allow
conversion of HW-rates.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: implement hw op for setting frame length in tx_hw_desc
Arik Nemtsov [Thu, 10 May 2012 09:13:19 +0000 (12:13 +0300)]
wl18xx: implement hw op for setting frame length in tx_hw_desc

Set the frame length during Tx in a way compatible with the 18xx FW.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: implement hw op for setting blocks in hw_tx_desc
Arik Nemtsov [Thu, 10 May 2012 09:13:18 +0000 (12:13 +0300)]
wl18xx: implement hw op for setting blocks in hw_tx_desc

Add the 18xx variant to the HW Tx descriptor union and set the 18xx
specific values during Tx.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: implement hw op for calculating hw block count per packet
Arik Nemtsov [Thu, 10 May 2012 09:13:17 +0000 (12:13 +0300)]
wl18xx: implement hw op for calculating hw block count per packet

Implement the calc_tx_blocks op for the 18xx family.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: set normal/GEM Tx spare block counts
Arik Nemtsov [Thu, 10 May 2012 09:13:16 +0000 (12:13 +0300)]
wl18xx: set normal/GEM Tx spare block counts

Initialize the Tx spare block counts for all operating modes in the 18xx
card.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: set the number of Tx descriptors
Arik Nemtsov [Thu, 10 May 2012 09:13:15 +0000 (12:13 +0300)]
wl18xx: set the number of Tx descriptors

Initialize the number of Tx-descriptors for the 18xx family.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: create per-chip-family private storage
Arik Nemtsov [Thu, 10 May 2012 09:13:14 +0000 (12:13 +0300)]
wl18xx: create per-chip-family private storage

Make use of the wlcore provided private storage in the 18xx low-level
driver.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: add trigger command and ack event operations
Luciano Coelho [Thu, 10 May 2012 09:13:13 +0000 (12:13 +0300)]
wl18xx: add trigger command and ack event operations

Add the operations that allow wlcore to trigger commands to the
firmware and acknowledge when an event has been fully received.

Allocate a private buffer to hold the maximum sized cmd. Send the
entire length of the buffer each time a command is sent to signal
EOT. Remove the previous EOT mechanism.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add some boot operations and hw-specific configurations
Luciano Coelho [Thu, 10 May 2012 09:13:12 +0000 (12:13 +0300)]
wl18xx: add some boot operations and hw-specific configurations

Implement the boot operation.  Add a wl18xx-specific configuration
structure (namely to configure the mac and phy parameters).

The default hw configuration matches the DVP board.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add identify chip operation
Luciano Coelho [Thu, 10 May 2012 09:13:11 +0000 (12:13 +0300)]
wl18xx: add identify chip operation

Add identify_chip operation to detect the chip ID for wl185x and set
the correct firmware name.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add register table
Luciano Coelho [Thu, 10 May 2012 09:13:10 +0000 (12:13 +0300)]
wl18xx: add register table

Add the register table with the appropriate values for wl18xx.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add partition table
Luciano Coelho [Thu, 10 May 2012 09:13:09 +0000 (12:13 +0300)]
wl18xx: add partition table

Define and add the partition table in the wlcore struct.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add empty operations struct
Luciano Coelho [Thu, 10 May 2012 09:13:08 +0000 (12:13 +0300)]
wl18xx: add empty operations struct

We don't have any chip-specific operations yet, but now wlcore has
defined an operations structure and requires the pointer to be set.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore_sdio/wl18xx: use SDIO revision number to identify wl18xx chips
Luciano Coelho [Thu, 10 May 2012 09:13:07 +0000 (12:13 +0300)]
wlcore_sdio/wl18xx: use SDIO revision number to identify wl18xx chips

At least in PG1, the wl18xx chips use the same SDIO vendor/device ID,
so it's not possible to figure out which driver is to be used.  As a
workaround, we can check the SDIO revision number, because wl18xx uses
3.00 and wl12xx does not.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowl18xx: add new module
Luciano Coelho [Thu, 10 May 2012 09:13:06 +0000 (12:13 +0300)]
wl18xx: add new module

Add the wl18xx module and the probe functions.  Use wlcore for the
main parts (not functional at this point due to differences in the
wl18xx initialization).

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agoLinux 3.5-rc1
Linus Torvalds [Sun, 3 Jun 2012 01:29:26 +0000 (18:29 -0700)]
Linux 3.5-rc1

12 years agoMerge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk...
Linus Torvalds [Sun, 3 Jun 2012 00:39:40 +0000 (17:39 -0700)]
Merge tag 'dm-3.5-changes-1' of git://git./linux/kernel/git/agk/linux-dm

Pull device-mapper updates from Alasdair G Kergon:
 "Improve multipath's retrying mechanism in some defined circumstances
  and provide a simple reserve/release mechanism for userspace tools to
  access thin provisioning metadata while the pool is in use."

* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm thin: provide userspace access to pool metadata
  dm thin: use slab mempools
  dm mpath: allow ioctls to trigger pg init
  dm mpath: delay retry of bypassed pg
  dm mpath: reduce size of struct multipath

12 years agodm thin: provide userspace access to pool metadata
Joe Thornber [Sat, 2 Jun 2012 23:30:01 +0000 (00:30 +0100)]
dm thin: provide userspace access to pool metadata

This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_.  This,
read-only snapshot can be accessed by userland, concurrently with the
live target.

Only one metadata snapshot can be held at a time.  The pool's status
line will give the block location for the current msnap.

Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:

    thin_dump -m <msnap root> <metadata dev>

Available here: https://github.com/jthornber/thin-provisioning-tools

Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:

     i) Incremental backups.

     By using metadata snapshots we can work out what blocks have
     changed over time.  Combined with data snapshots we can ensure
     the data doesn't change while we back it up.

     A short proof of concept script can be found here:

     https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb

     ii) Migration of thin devices from one pool to another.

     iii) Merging snapshots back into an external origin.

     iv) Asyncronous replication.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
12 years agodm thin: use slab mempools
Mike Snitzer [Sat, 2 Jun 2012 23:30:00 +0000 (00:30 +0100)]
dm thin: use slab mempools

Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
12 years agodm mpath: allow ioctls to trigger pg init
Mikulas Patocka [Sat, 2 Jun 2012 23:29:58 +0000 (00:29 +0100)]
dm mpath: allow ioctls to trigger pg init

After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device.  Until this has happened, ioctls return -EAGAIN.

With this patch, new paths are made available in response to an ioctl
too.  The processing of the ioctl gets delayed until this has happened.

Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.

Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure.  Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands).  For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too.  It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
12 years agodm mpath: delay retry of bypassed pg
Mike Christie [Sat, 2 Jun 2012 23:29:45 +0000 (00:29 +0100)]
dm mpath: delay retry of bypassed pg

If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.

If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
12 years agodm mpath: reduce size of struct multipath
Mike Snitzer [Sat, 2 Jun 2012 23:29:43 +0000 (00:29 +0100)]
dm mpath: reduce size of struct multipath

Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes.  Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes).  This allows future flags to be added
without each consuming an unsigned int.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
12 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Sat, 2 Jun 2012 23:22:51 +0000 (16:22 -0700)]
Merge git://git./linux/kernel/git/davem/net

Pull networking updates from David Miller:

 1) Make syn floods consume significantly less resources by

    a) Not pre-COW'ing routing metrics for SYN/ACKs
    b) Mirroring the device queue mapping of the SYN for the SYN/ACK
       reply.

    Both from Eric Dumazet.

 2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.

 3) Validate the length requested when building a paged SKB for a
    socket, so we don't overrun the page vector accidently.  From Jason
    Wang.

 4) When netlabel is disabled, we abort all IP option processing when we
    see a CIPSO option.  This isn't the right thing to do, we should
    simply skip over it and continue processing the remaining options
    (if any).  Fix from Paul Moore.

 5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
    Apfelbaum.

 6) 8139cp enables the receiver before the ring address is properly
    programmed, which potentially lets the device crap over random
    memory.  Fix from Jason Wang.

 7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
    address reference in jumbo RX frame processing from Bruce Allan and
    Sebastian Andrzej Siewior, respectively.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  fec_mpc52xx: fix timestamp filtering
  mcs7830: Implement link state detection
  e1000e: fix Rapid Start Technology support for i217
  e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
  r8169: call netif_napi_del at errpaths and at driver unload
  tcp: reflect SYN queue_mapping into SYNACK packets
  tcp: do not create inetpeer on SYNACK message
  8139cp/8139too: terminate the eeprom access with the right opmode
  8139cp: set ring address before enabling receiver
  cipso: handle CIPSO options correctly when NetLabel is disabled
  net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
  bql: Avoid possible inconsistent calculation.
  bql: Avoid unneeded limit decrement.
  bql: Fix POSDIFF() to integer overflow aware.
  net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
  net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
  net/mlx4_core: Fixes for VF / Guest startup flow
  net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
  net/mlx4_core: Fix number of EQs used in ICM initialisation
  net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int

12 years agoMerge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Sat, 2 Jun 2012 23:17:03 +0000 (16:17 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull straggler x86 fixes from Peter Anvin:
 "Three groups of patches:

  - EFI boot stub documentation and the ability to print error messages;
  - Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
    should never have been ported, and the port is broken and
    potentially dangerous.)
  - ftrace stack corruption fixes.  I'm not super-happy about the
    technical implementation, but it is probably the least invasive in
    the short term.  In the future I would like a single method for
    nesting the debug stack, however."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
  x86, efi: Add EFI boot stub documentation
  x86, efi; Add EFI boot stub console support
  x86, efi: Only close open files in error path
  ftrace/x86: Do not change stacks in DEBUG when calling lockdep
  x86: Allow nesting of the debug stack IDT setting
  x86: Reset the debug_stack update counter
  ftrace: Use breakpoint method to update ftrace caller
  ftrace: Synchronize variable setting with breakpoints

12 years agotty: Revert the tty locking series, it needs more work
Linus Torvalds [Sat, 2 Jun 2012 22:21:43 +0000 (15:21 -0700)]
tty: Revert the tty locking series, it needs more work

This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.

The main revert is d29f3ef39be4 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:

  fde86d310886 - tty: add lockdep annotations
  8f6576ad476b - tty: fix ldisc lock inversion trace
  d3ca8b64b97e - pty: Fix lock inversion
  b1d679afd766 - tty: drop the pty lock during hangup
  abcefe5fc357 - tty/amiserial: Add missing argument for tty_unlock()
  fd11b42e3598 - cris: fix missing tty arg in wait_event_interruptible_tty call
  d29f3ef39be4 - tty_lock: Localise the lock

The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agofec_mpc52xx: fix timestamp filtering
Stephan Gatzka [Sat, 2 Jun 2012 03:04:06 +0000 (03:04 +0000)]
fec_mpc52xx: fix timestamp filtering

skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.

Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agomcs7830: Implement link state detection
Ondrej Zary [Fri, 1 Jun 2012 10:29:08 +0000 (10:29 +0000)]
mcs7830: Implement link state detection

Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge 'for-linus' branches from git://git.kernel.org/pub/scm/linux/kernel/git/viro...
Linus Torvalds [Sat, 2 Jun 2012 16:03:54 +0000 (09:03 -0700)]
Merge 'for-linus' branches from git://git./linux/kernel/git/viro/{vfs,signal}

Pull vfs fix and a fix from the signal changes for frv from Al Viro.

The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short".  Al didn't notice, and
made both of them be the unsigned short.

The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  powerpc: Fix size of st_nlink on 64bit

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  frv: Remove bogus closing parenthesis

12 years agopowerpc: Fix size of st_nlink on 64bit
Anton Blanchard [Sat, 2 Jun 2012 11:34:52 +0000 (21:34 +1000)]
powerpc: Fix size of st_nlink on 64bit

commit e57f93cc53b7 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
12 years agofrv: Remove bogus closing parenthesis
Geert Uytterhoeven [Sat, 2 Jun 2012 11:08:39 +0000 (13:08 +0200)]
frv: Remove bogus closing parenthesis

Introduced by commit 6fd84c0831ec78d98736b76dc5e9b849f1dbfc9e
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
12 years agoe1000e: fix Rapid Start Technology support for i217
Bruce Allan [Thu, 10 May 2012 02:51:17 +0000 (02:51 +0000)]
e1000e: fix Rapid Start Technology support for i217

The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.

Also for clarity, rename a few defines as bit definitions instead of masks.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
12 years agoe1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
Sebastian Andrzej Siewior [Tue, 15 May 2012 09:18:55 +0000 (09:18 +0000)]
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()

This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
12 years agoMerge branch 'akpm' (Fixups for Andrew's patchbomb)
Linus Torvalds [Sat, 2 Jun 2012 02:56:23 +0000 (19:56 -0700)]
Merge branch 'akpm' (Fixups for Andrew's patchbomb)

Merge fixups for the mac NLS tables from Andrew.

* emailed from Andrew Morton, and one cleanup by me:
  nls: fix (and rename) mac NLS table files and config options
  fs/nls/Makefile: remove bogus CONFIG_ assignments

12 years agonls: fix (and rename) mac NLS table files and config options
Linus Torvalds [Sat, 2 Jun 2012 02:51:22 +0000 (19:51 -0700)]
nls: fix (and rename) mac NLS table files and config options

The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).

And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".

So rename the options to be consistent, and be NLS_MAC_xyzzy.  Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agofs/nls/Makefile: remove bogus CONFIG_ assignments
Andrew Morton [Fri, 1 Jun 2012 21:57:41 +0000 (14:57 -0700)]
fs/nls/Makefile: remove bogus CONFIG_ assignments

These were debug things which snuck through.

Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agoMerge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Linus Torvalds [Fri, 1 Jun 2012 23:57:51 +0000 (16:57 -0700)]
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6

Pull fbdev updates from Florian Tobias Schandinat:
 - driver for AUO-K1900 and AUO-K1901 epaper controller
 - large updates for OMAP (e.g. decouple HDMI audio and video)
 - some updates for Exynos and SH Mobile
 - various other small fixes and cleanups

* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
  video: bfin_adv7393fb: Fix cleanup code
  video: exynos_dp: reduce delay time when configuring video setting
  video: exynos_dp: move sw reset prioir to enabling sw defined function
  video: exynos_dp: use devm_ functions
  fb: handle NULL pointers in framebuffer release
  OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
  OMAPDSS: Apply VENC timings even if panel is disabled
  OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
  OMAPDSS: DISPC: Support rotation through TILER
  OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
  OMAPFB: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
  OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
  OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
  OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
  drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
  video: exynos mipi dsi: support reverse panel type
  video: exynos mipi dsi: Properly interpret the interrupt source flags
  video: exynos mipi dsi: Avoid races in probe()
  ...

12 years agoMerge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Linus Torvalds [Fri, 1 Jun 2012 23:55:42 +0000 (16:55 -0700)]
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd

Pull mtd update from David Woodhouse:
 - More robust parsing especially of xattr data in JFFS2
 - Updates to mxc_nand and gpmi drivers to support new boards and device tree
 - Improve consistency of information about ECC strength in NAND devices
 - Clean up partition handling of plat_nand
 - Support NAND drivers without dedicated access to OOB area
 - BCH hardware ECC support for OMAP
 - Other fixes and cleanups, and a few new device IDs

Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.

* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
  mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
  mtd: block2mtd: fix recursive call of mtd_writev
  mtd: gpmi-nand: define ecc.strength
  mtd: of_parts: fix breakage in Kconfig
  mtd: nand: fix scan_read_raw_oob
  mtd: docg3 fix in-middle of blocks reads
  mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
  mtd: add fixup for S29NS512P NOR flash.
  jffs2: allow to complete xattr integrity check on first GC scan
  jffs2: allow to discriminate between recoverable and non-recoverable errors
  mtd: nand: omap: add support for hardware BCH ecc
  ARM: OMAP3: gpmc: add BCH ecc api and modes
  mtd: nand: check the return code of 'read_oob/read_oob_raw'
  mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
  mtd: m25p80: Add support for Winbond W25Q80BW
  jffs2: get rid of jffs2_sync_super
  jffs2: remove unnecessary GC pass on sync
  jffs2: remove unnecessary GC pass on umount
  jffs2: remove lock_super
  mtd: gpmi: add gpmi support for mx6q
  ...

12 years agoMerge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Linus Torvalds [Fri, 1 Jun 2012 23:51:37 +0000 (16:51 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86

Pull x86 platform driver updates from Matthew Garrett:
 "Some significant improvements for the Sony driver on newer machines,
  but other than that mostly just minor fixes and a patch to remove the
  broken rfkill code from the Dell driver."

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (35 commits)
  apple-gmux: Fix up the suspend/resume patch
  dell-laptop: Remove rfkill code
  toshiba_acpi: Fix mis-merge
  dell-laptop: Add touchpad led support for Dell V3450
  acer-wmi: add 3 laptops to video backlight vendor mode quirk table
  sony-laptop: add touchpad enable/disable function
  sony-laptop: add missing Fn key combos for 0x100 handlers
  sony-laptop: add support for more WWAN modems
  sony-laptop: new keyboard backlight handle
  sony-laptop: add high speed battery charging function
  sony-laptop: support automatic resume on lid open
  sony-laptop: adjust error handling in finding SNC handles
  sony-laptop: add thermal profiles support
  sony-laptop: support battery care functions
  sony-laptop: additional debug statements
  sony-laptop: improve SNC initialization and acpi notify callback code
  sony-laptop: use kstrtoul to parse sysfs values
  sony-laptop: generalise ACPI calls into SNC functions
  sony-laptop: fix return path when no ACPI buffer is allocated
  sony-laptop: use soft rfkill status stored in hw
  ...

12 years agoMerge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penber...
Linus Torvalds [Fri, 1 Jun 2012 23:50:23 +0000 (16:50 -0700)]
Merge branch 'slab/for-linus' of git://git./linux/kernel/git/penberg/linux

Pull slab updates from Pekka Enberg:
 "Mainly a bunch of SLUB fixes from Joonsoo Kim"

* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slub: use __SetPageSlab function to set PG_slab flag
  slub: fix a memory leak in get_partial_node()
  slub: remove unused argument of init_kmem_cache_node()
  slub: fix a possible memory leak
  Documentations: Fix slabinfo.c directory in vm/slub.txt
  slub: fix incorrect return type of get_any_partial()

12 years agoMerge remote-tracking branch 'rostedt/tip/perf/urgent-2' into x86-urgent-for-linus
H. Peter Anvin [Fri, 1 Jun 2012 22:55:31 +0000 (15:55 -0700)]
Merge remote-tracking branch 'rostedt/tip/perf/urgent-2' into x86-urgent-for-linus

12 years agoMerge branch 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm...
Linus Torvalds [Fri, 1 Jun 2012 22:46:46 +0000 (15:46 -0700)]
Merge branch 'ux500/hickup' of git://git./linux/kernel/git/arm/arm-soc

Pull arm fixes for ux500 mismerge mishap from Arnd Bergmann:
 "The device tree conversion for arm/ux500 in 3.5 turns out to be
  incomplete because of a mismerge done by Linus Walleij that I failed
  to notice early enough and that Lee Jones as the original author of
  those patches did not manage to fix during the -next cycle.  While we
  originally to get a much larger set of ux500 device tree enablement
  patches merged, this did not happen in time.

  After some discussion at Linaro Connect conference this week, Lee has
  been able to do damage control and provide a series to put the broken
  platform back into usable shape for both DT and non-DT based booting.

  This series has not been part of linux-next and is based on top of the
  current state of the upstream kernel rather than an -rc, but this is
  the best we could manage given the earlier breakage."

* 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: ux500: Enable probing of pinctrl through Device Tree
  ARM: ux500: Add support for ab8500 regulators into the Device Tree
  ARM: ux500: Provide regulator support for SMSC911x via Device Tree
  ARM: ux500: Allow PRCMU regulator to be probed during a DT enabled boot
  ARM: ux500: Apply db8500-prcmu regulator information to db8500 Device Tree
  ARM: ux500: Only initialise STE's UIBs on boards which support them
  ARM: ux500: Disable platform setup of the ab8500 when DT is enabled
  ARM: ux500: Use correct format for dynamic IRQ assignment
  ARM: ux500: Re-enable SMSC911x platform code registration during non-DT boots
  ARM: ux500: PRCMU related configuration and layout corrections for Device Tree
  ARM: ux500: Remove DB8500 PRCMU platform registration when DT is enabled
  ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
  ARM: ux500: New DT:ed u8500_init_devices for one-by-one device enablement
  ARM: ux500: New DT:ed snowball_platform_devs for one-by-one device enablement
  pinctrl-nomadik: Allow Device Tree driver probing

12 years agor8169: call netif_napi_del at errpaths and at driver unload
Devendra Naga [Thu, 31 May 2012 01:51:20 +0000 (01:51 +0000)]
r8169: call netif_napi_del at errpaths and at driver unload

when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.

Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Linus Torvalds [Fri, 1 Jun 2012 22:40:29 +0000 (15:40 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
 "A bunch of fixes:
   - vmware memory corruption
   - ttm spinlock balance
   - cirrus/mgag200 work in the presence of efifb
  and finally Alex and Jerome managed to track down a magic set of bits
  that on certain rv740 and evergreen cards allow the correct use of the
  complete set of render backends, this makes the cards operate
  correctly in a number of scenarios we had issues in before, it also
  manages to boost speed on benchmarks my large amounts on these
  specific gpus."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/edid: Make the header fixup threshold tunable
  drm/radeon: fix regression in UMS CS ioctl
  drm/vmwgfx: Fix nasty write past alloced memory area
  drm/ttm: Fix spinlock imbalance
  drm/radeon: fixup tiling group size and backendmap on r6xx-r9xx (v4)
  drm/radeon: fix HD6790, HD6570 backend programming
  drm/radeon: properly program gart on rv740, juniper, cypress, barts, hemlock
  drm/radeon: fix bank information in tiling config
  drm/mgag200: kick off conflicting framebuffers earlier.
  drm/cirrus: kick out conflicting framebuffers earlier
  cirrus: avoid crash if driver fails to load

12 years agoMerge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Linus Torvalds [Fri, 1 Jun 2012 22:39:26 +0000 (15:39 -0700)]
Merge tag 'sound-3.5' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
 "Just a few trivial driver-specific fixes."

* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hdspm - Work around broken DDS value on PCI RME MADI
  ALSA: usb-audio: fix rate_list memory leak
  ASoC: fsi: bugfix: ensure dma is terminated
  ASoC: fsi: bugfix: correct dma area
  ASoC: fsi: bugfix: enable master clock control on DMA stream
  ASoC: imx-ssi: Use clk_prepare_enable/clk_disable_unprepare

12 years agox86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
H.J. Lu [Tue, 22 May 2012 03:29:45 +0000 (20:29 -0700)]
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32

When I added x32 ptrace to 3.4 kernel, I also include PTRACE_ARCH_PRCTL
support for x32 GDB  For ARCH_GET_FS/GS, it takes a pointer to int64.  But
at user level, ARCH_GET_FS/GS takes a pointer to int32.  So I have to add
x32 ptrace to glibc to handle it with a temporary int64 passed to kernel and
copy it back to GDB as int32.  Roland suggested that PTRACE_ARCH_PRCTL
is obsolete and x32 GDB should use fs_base and gs_base fields of
user_regs_struct instead.

Accordingly, remove PTRACE_ARCH_PRCTL completely from the x32 code to
avoid possible memory overrun when pointer to int32 is passed to
kernel.

Link: http://lkml.kernel.org/r/CAMe9rOpDzHfS7NH7m1vmD9QRw8SSj4Sc%2BaNOgcWm_WJME2eRsQ@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org> v3.4
12 years agomtd: mxc_nand: move ecc strengh setup before nand_scan_tail
Sascha Hauer [Fri, 25 May 2012 14:22:42 +0000 (16:22 +0200)]
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail

Since commit 6a918bade9dab40aaef80559bd1169c69e8d69cb, the mxc_nand driver
fails with:

Driver must set ecc.strength when using hardware ECC

This is because nand_scan_tail checks for correct ecc strength
settings, so we must set them up before nand_scan_tail.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org [3.4+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: block2mtd: fix recursive call of mtd_writev
Gabor Juhos [Wed, 23 May 2012 22:17:23 +0000 (00:17 +0200)]
mtd: block2mtd: fix recursive call of mtd_writev

The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.

This is caused by 1dbebd32562b3c2caeca35960e5cb00bfcc12900
(mtd: harmonize mtd_writev usage).

Remove the assignment from the block2mtd driver to fix the
issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: gpmi-nand: define ecc.strength
Marek Vasut [Mon, 21 May 2012 20:59:27 +0000 (22:59 +0200)]
mtd: gpmi-nand: define ecc.strength

Fix an issue which was introduced by the recent addition of ecc.strength.

The ecc.strength wasn't set in gpmi-nand, resulting in the following crash:
[    2.550000] kernel BUG at drivers/mtd/nand/nand_base.c:3347!
...
[    2.550000] [<c020841c>] (nand_scan_tail+0x328/0x650) from [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4)
[    2.550000] [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4) from [<c01f6618>] (platform_drv_probe+0x14/0x18)
[    2.550000] [<c01f6618>] (platform_drv_probe+0x14/0x18) from [<c01f55b0>] (driver_probe_device+0x74/0x1fc)
[    2.550000] [<c01f55b0>] (driver_probe_device+0x74/0x1fc) from [<c01f57cc>] (__driver_attach+0x94/0x98)
[    2.550000] [<c01f57cc>] (__driver_attach+0x94/0x98) from [<c01f3d40>] (bus_for_each_dev+0x50/0x80)
[    2.550000] [<c01f3d40>] (bus_for_each_dev+0x50/0x80) from [<c01f4e18>] (bus_add_driver+0x188/0x25c)
[    2.550000] [<c01f4e18>] (bus_add_driver+0x188/0x25c) from [<c01f5a70>] (driver_register+0x78/0x138)
[    2.550000] [<c01f5a70>] (driver_register+0x78/0x138) from [<c043dc7c>] (gpmi_nand_init+0xc/0x30)
[    2.550000] [<c043dc7c>] (gpmi_nand_init+0xc/0x30) from [<c0008824>] (do_one_initcall+0x108/0x17c)
[    2.550000] [<c0008824>] (do_one_initcall+0x108/0x17c) from [<c042a8b8>] (kernel_init+0xfc/0x1bc)
[    2.550000] [<c042a8b8>] (kernel_init+0xfc/0x1bc) from [<c000fab4>] (kernel_thread_exit+0x0/0x8)

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agoapple-gmux: Fix up the suspend/resume patch
Matthew Garrett [Fri, 1 Jun 2012 19:18:52 +0000 (15:18 -0400)]
apple-gmux: Fix up the suspend/resume patch

I incorporated the wrong version of the suspend/resume patch for gmux,
and so lost David Woodhouse's fix to leave the backlight level unchanged
over suspend/resume. This fixes it up to v2.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
12 years agomtd: of_parts: fix breakage in Kconfig
Frank Svendsboe [Thu, 17 May 2012 20:43:09 +0000 (22:43 +0200)]
mtd: of_parts: fix breakage in Kconfig

MTD_OF_PARTS and the default setting is not working due to using 'Y'
instead of 'y', introduced in commit
d6137badeff1ef64b4e0092ec249ebdeaeb3ff37. This made our board, and
possibly other boards using DTS defined partitions and not having
CONFIG_MTD_OF_PARTS=y defined in the defconfig, fail to mount root.

Signed-off-by: Frank Svendsboe <frank.svendsboe@gmail.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Linus Torvalds [Fri, 1 Jun 2012 18:53:44 +0000 (11:53 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/signal

Pull third pile of signal handling patches from Al Viro:
 "This time it's mostly helpers and conversions to them; there's a lot
  of stuff remaining in the tree, but that'll either go in -rc2
  (isolated bug fixes, ideally via arch maintainers' trees) or will sit
  there until the next cycle."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  x86: get rid of calling do_notify_resume() when returning to kernel mode
  blackfin: check __get_user() return value
  whack-a-mole with TIF_FREEZE
  FRV: Optimise the system call exit path in entry.S [ver #2]
  FRV: Shrink TIF_WORK_MASK [ver #2]
  FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
  new helper: signal_delivered()
  powerpc: get rid of restore_sigmask()
  most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
  set_restore_sigmask() is never called without SIGPENDING (and never should be)
  TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
  don't call try_to_freeze() from do_signal()
  pull clearing RESTORE_SIGMASK into block_sigmask()
  sh64: failure to build sigframe != signal without handler
  openrisc: tracehook_signal_handler() is supposed to be called on success
  new helper: sigmask_to_save()
  new helper: restore_saved_sigmask()
  new helpers: {clear,test,test_and_clear}_restore_sigmask()
  HAVE_RESTORE_SIGMASK is defined on all architectures now

12 years agotcp: reflect SYN queue_mapping into SYNACK packets
Eric Dumazet [Fri, 1 Jun 2012 01:47:50 +0000 (01:47 +0000)]
tcp: reflect SYN queue_mapping into SYNACK packets

While testing how linux behaves on SYNFLOOD attack on multiqueue device
(ixgbe), I found that SYNACK messages were dropped at Qdisc level
because we send them all on a single queue.

Obvious choice is to reflect incoming SYN packet @queue_mapping to
SYNACK packet.

Under stress, my machine could only send 25.000 SYNACK per second (for
200.000 incoming SYN per second). NIC : ixgbe with 16 rx/tx queues.

After patch, not a single SYNACK is dropped.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agotcp: do not create inetpeer on SYNACK message
Eric Dumazet [Thu, 31 May 2012 21:00:26 +0000 (21:00 +0000)]
tcp: do not create inetpeer on SYNACK message

Another problem on SYNFLOOD/DDOS attack is the inetpeer cache getting
larger and larger, using lots of memory and cpu time.

tcp_v4_send_synack()
->inet_csk_route_req()
 ->ip_route_output_flow()
  ->rt_set_nexthop()
   ->rt_init_metrics()
    ->inet_getpeer( create = true)

This is a side effect of commit a4daad6b09230 (net: Pre-COW metrics for
TCP) added in 2.6.39

Possible solution :

Instruct inet_csk_route_req() to remove FLOWI_FLAG_PRECOW_METRICS

Before patch :

# grep peer /proc/slabinfo
inet_peer_cache   4175430 4175430    192   42    2 : tunables    0    0    0 : slabdata  99415  99415      0

Samples: 41K of event 'cycles', Event count (approx.): 30716565122
+  20,24%      ksoftirqd/0  [kernel.kallsyms]           [k] inet_getpeer
+   8,19%      ksoftirqd/0  [kernel.kallsyms]           [k] peer_avl_rebalance.isra.1
+   4,81%      ksoftirqd/0  [kernel.kallsyms]           [k] sha_transform
+   3,64%      ksoftirqd/0  [kernel.kallsyms]           [k] fib_table_lookup
+   2,36%      ksoftirqd/0  [ixgbe]                     [k] ixgbe_poll
+   2,16%      ksoftirqd/0  [kernel.kallsyms]           [k] __ip_route_output_key
+   2,11%      ksoftirqd/0  [kernel.kallsyms]           [k] kernel_map_pages
+   2,11%      ksoftirqd/0  [kernel.kallsyms]           [k] ip_route_input_common
+   2,01%      ksoftirqd/0  [kernel.kallsyms]           [k] __inet_lookup_established
+   1,83%      ksoftirqd/0  [kernel.kallsyms]           [k] md5_transform
+   1,75%      ksoftirqd/0  [kernel.kallsyms]           [k] check_leaf.isra.9
+   1,49%      ksoftirqd/0  [kernel.kallsyms]           [k] ipt_do_table
+   1,46%      ksoftirqd/0  [kernel.kallsyms]           [k] hrtimer_interrupt
+   1,45%      ksoftirqd/0  [kernel.kallsyms]           [k] kmem_cache_alloc
+   1,29%      ksoftirqd/0  [kernel.kallsyms]           [k] inet_csk_search_req
+   1,29%      ksoftirqd/0  [kernel.kallsyms]           [k] __netif_receive_skb
+   1,16%      ksoftirqd/0  [kernel.kallsyms]           [k] copy_user_generic_string
+   1,15%      ksoftirqd/0  [kernel.kallsyms]           [k] kmem_cache_free
+   1,02%      ksoftirqd/0  [kernel.kallsyms]           [k] tcp_make_synack
+   0,93%      ksoftirqd/0  [kernel.kallsyms]           [k] _raw_spin_lock_bh
+   0,87%      ksoftirqd/0  [kernel.kallsyms]           [k] __call_rcu
+   0,84%      ksoftirqd/0  [kernel.kallsyms]           [k] rt_garbage_collect
+   0,84%      ksoftirqd/0  [kernel.kallsyms]           [k] fib_rules_lookup

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years ago8139cp/8139too: terminate the eeprom access with the right opmode
Jason Wang [Thu, 31 May 2012 18:19:48 +0000 (18:19 +0000)]
8139cp/8139too: terminate the eeprom access with the right opmode

Currently, we terminate the eeprom access through clearing the CS by:

RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);

This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.

Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years ago8139cp: set ring address before enabling receiver
Jason Wang [Thu, 31 May 2012 18:19:39 +0000 (18:19 +0000)]
8139cp: set ring address before enabling receiver

Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.

btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.

Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agocipso: handle CIPSO options correctly when NetLabel is disabled
Paul Moore [Fri, 1 Jun 2012 05:54:56 +0000 (05:54 +0000)]
cipso: handle CIPSO options correctly when NetLabel is disabled

When NetLabel is not enabled, e.g. CONFIG_NETLABEL=n, and the system
receives a CIPSO tagged packet it is dropped (cipso_v4_validate()
returns non-zero).  In most cases this is the correct and desired
behavior, however, in the case where we are simply forwarding the
traffic, e.g. acting as a network bridge, this becomes a problem.

This patch fixes the forwarding problem by providing the basic CIPSO
validation code directly in ip_options_compile() without the need for
the NetLabel or CIPSO code.  The new validation code can not perform
any of the CIPSO option label/value verification that
cipso_v4_validate() does, but it can verify the basic CIPSO option
format.

The behavior when NetLabel is enabled is unchanged.

Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>