ARM: mach-shmobile: Clean up headsmp.S

Use PAGE_OFFSET and PHYS_OFFSET for secondary_startup
entry point as recommended by Russell King.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: sh73a0 SMP support

Add SMP support for ag5evm and the sh73a0 processor.

Onlining and offlining works well, but at this point
offlined processor cores are not put into sleep mode.

There is no spinlock for syncing the secondary core
with the first one in this implementation. The code
instead relies on the cpu_online() check in __cpu_up().

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: Enable SMP support

Allow SMP to be enabled on R-Mobile / SH-Mobile.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: SMP base support

Add SMP base support for R-Mobile / SH-Mobile processors.

This patch contains all base code to support CONFIG_SMP
regardless of ARCH_SHMOBILE processor type. Both local timer
and CPU hotplug are supported, but no processor specific
code is included.

At this point only the default behavior is in place, so
a single core will always be used even though CONFIG_SMP
is enabled on multicore systems.

The SMP Kconfig entry for arch/arm/Kconfig is excluded from
this patch to simplify merging.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: Fix up pinmux entries in Makefile

Compiling in multiple CPUs into the same kernel binary
requires a Makefile update. With this patch in place
it is possible to enable the pinmux code for both the
SH7372 and the SH7377.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branches 'rmobile/ag5' and 'rmobile/mackerel' into rmobile-latest

ARM: mach-shmobile: mackerel: Add keypad tca6408a support

This patch maps key0/key1/key2/key3 as HOME/MENU/BACK/POWER buttons
on mackerel board.

Signed-off-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: Add Accelerometer sensor support

Signed-off-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: AG5 clock framework improvements

This patch improves the state of the AG5 clock
framework support. The main clock parent is
automatically detected, but most of the clocks
are not used by any driver or subsystem at this
point. More work is needed for support of multi
media hardware such as FSI and/or LCDC/MIPI-DSI.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: Add FSI-AK4643 support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: Add LEDs support

you can control it by
echo 0 > /sys/class/leds/led0/brightness
echo 1 > /sys/class/leds/led0/brightness

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branch 'rmobile/mackerel' into rmobile-latest

Conflicts:
arch/arm/mach-shmobile/Kconfig
arch/arm/mach-shmobile/Makefile

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branches 'rmobile/ag5' and 'rmobile/mmcif' into rmobile-latest

Merge branch 'common/mmcif' into rmobile/mmcif

ARM: mach-shmobile: mackerel: Add USB1(Host) support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: Add lost GPIO_FN_LCDD 18 - 23

RGB24 bus needs 18-23 pin

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: Add mackerel defconfig

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: document switch and pin modes.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: Add LCDC support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: mackerel: Add SMSC support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: Add mackerel board support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: ag5evm: Add FSI resources

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sh, mmc: Use defines when setting CE_CLK_CTRL

The 16-19th bits of CE_CLK_CTRL set the
MMC clock frequency.

Cc: Yusuke Goda <yusuke.goda.sx@renesas.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

mmc, sh: Correct value for reset

This resolves a regression that I introduced in
"mmc, sh: Move constants to sh_mmcif.h". Having
examined the manual and tested the code on an AP4EVB board
it seems that the correct sequence is.

1) Write 1 to bit 31 and zeros to all other bits
2) Write zero to all bits

Cc: Yusuke Goda <yusuke.goda.sx@renesas.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sh, mmc: Make mmcif_update_progress static inline

extern inline doesn't make much sense

Cc: Yusuke Goda <yusuke.goda.sx@renesas.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branch 'rmobile/mmcif' into rmobile-latest

ARM: mach-shmobile: clock-sh73a0: modify MSTP order

This patch permuted clock arrays in the order of MSTP

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: enable MMCIF DMA on ap4evb

Have to add DMA slave configuration to enable DMA for the sh7372 MMCIF
controller.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

mmc: sh_mmcif: add DMA support

The MMCIF controller on sh-mobile platforms can use the DMA controller for data
transfers. Interface to the SH dmaengine driver to enable DMA. We also have to
lower the maximum number of segments to match with the number od DMA
descriptors on SuperH, this doesn't significantly affect driver's PIO
performance.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

mmc: sh_mmcif: cosmetic clean up

Replace pr_* with respective dev_*, sort headers alphabetically, remove an
unused struct member, superfluous variable initialisations and type-casts.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: add DMA defines for MMCIF on sh7372

Add DMA slave IDs and slave definitions for MMCIF on sh7372.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

mmc: sh_mmcif: switch to completion, fix flags

In sh_mmcif.c an event is used as a completion, switch over. When a
wait_for_completion*_timeout() returns, it suffices to check the remaining
time, setting an additional flag before waking up the waiting task only reduces
the race window, but does not eliminate it. This patch switches the driver to
use a completion to signal an interrupt, the only case, when an interrupt
should not wake up the waiter, is when an automatic CMD12 completes. Also fix
MODULE_ALIAS.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branch 'common/mmcif' into rmobile/mmcif

Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (lis3lv02d_i2c) Fix compile warnings
  hwmon: (i5k_amb) Fix compile warning

Merge branch 'for-linus' of git://git./linux/kernel/git/konrad/xen

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen: remove duplicated #include
  xen: x86/32: perform initial startup on initial_page_table

Merge git://git./linux/kernel/git/cmetcalf/linux-tile

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile: fix memchr() not to dereference memory for zero length
  arch/tile: make glibc's sysconf(_SC_NPROCESSORS_CONF) work correctly
  arch/tile: fix rwlock so would-be write lockers don't block new readers

Merge branch 'drivers' of git://git./linux/kernel/git/cmetcalf/linux-tile

* 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  pci root complex: support for tile architecture
  drivers/net/tile/: on-chip network drivers for the tile architecture
  MAINTAINERS: add drivers/char/hvc_tile.c as maintained by tile

Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6482/2: Fix find_next_zero_bit and related assembly
  ARM: 6490/1: MM: bugfix: initialize spinlock for init_mm.context
  ARM: avoid annoying <4>'s in printk output
  SCSI: arm fas216: fix missing ';'
  ARM: avoid marking decompressor .stack section as having contents
  ARM: 6489/1: thumb2: fix incorrect optimisation in usracc
  ARM: 6488/1: nomadik: prevent sched_clock() wraparound
  ARM: 6484/1: fix compile warning in mm/init.c
  ARM: 6473/1: Small update to ux500 specific L2 cache code
  ARM: improve compiler's ability to optimize page tables
  mx25: fix spi device registration typo
  ARM i.MX27 eukrea: Fix compilation
  ARM i.MX spi: fix compilation for i.MX21
  ARM i.MX pcm037 eet: compile fixes
  ARM i.MX: sdma is merged, so remove #ifdef SDMA_IS_MERGED
  ARM mx3fb: check for DMA engine type
  mach-pcm037_eet: Fix section mismatch for eet_init_devices()

Merge branch 'fbdev-fixes-for-linus' of git://git./linux/kernel/git/lethal/fbdev-2.6

* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
  sisfb: delete osdef.h
  sisfb: move the CONFIG warning to sis_main.c
  sisfb: replace SiS_SetMemory with memset_io
  sisfb: remove InPort/OutPort wrappers
  sisfb: use CONFIG_FB_SIS_301/315 instead of SIS301/315H
  sisfb: delete redudant #define SIS_LINUX_KERNEL
  sisfb: delete dead SIS_XORG_XF86 code
  sisfb: delete fallback code for pci_map_rom()
  sisfb: delete obsolete PCI ROM bug workaround
  fbdev: Update documentation index file.
  lxfb: Program panel v/h sync output polarity correctly
  fbcmap: integer overflow bug
  fbcmap: cleanup white space in fb_alloc_cmap()
  MAINTAINERS: Add fbdev patchwork entry, tidy up file patterns.
  fbdev: da8xx: punt duplicated FBIO_WAITFORVSYNC define
  fbdev: sh_mobile_lcdcfb: fix bug in reconfig()

Merge branch 'sh-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: clkfwk: Build fix for non-legacy CPG changes.
  sh: Use GCC __builtin_prefetch() to implement prefetch().
  sh: fix vsyscall compilation due to .eh_frame issue
  sh: avoid to flush all cache in sys_cacheflush
  sh: clkfwk: Disable init clk op for non-legacy clocks.
  sh: clkfwk: Kill off now unused algo_id in set_rate op.
  sh: clkfwk: Kill off unused clk_set_rate_ex().

Merge branch 'for-linus' of git://neil.brown.name/md

* 'for-linus' of git://neil.brown.name/md:
  md: Call blk_queue_flush() to establish flush/fua support
  md/raid1: really fix recovery looping when single good device fails.
  md: fix return value of rdev_size_change()

Merge git://git./linux/kernel/git/rusty/linux-2.6-for-linus

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  virtio: fix format of sysfs driver/vendor files
  Char: virtio_console, fix memory leak
  virtio: return correct capacity to users
  module: Update prototype for ref_module (formerly use_module)

arch/x86/include/asm/fixmap.h: mark __set_fixmap_offset as __always_inline

When compiling arch/x86/kernel/early_printk_mrst.c with i386
allmodconfig, gcc-4.1.0 generates an out-of-line copy of
__set_fixmap_offset() which contains a reference to
__this_fixmap_does_not_exist which the compiler cannot elide.

Marking __set_fixmap_offset() as __always_inline prevents this.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Feng Tang <feng.tang@intel.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts: fix gfp-translate for recent changes to gfp.h

The recent changes to gfp.h to satisfy sparse broke scripts/gfp-translate.
This patch fixes it up to work with old and new versions of gfp.h .

[akpm@linux-foundation.org: use `grep -q', per WANG Cong]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Namhyung Kim <namhyung@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

reiserfs: fix inode mutex - reiserfs lock misordering

reiserfs_unpack() locks the inode mutex with reiserfs_mutex_lock_safe()
to protect against reiserfs lock dependency.  However this protection
requires to have the reiserfs lock to be locked.

This is the case if reiserfs_unpack() is called by reiserfs_ioctl but
not from reiserfs_quota_on() when it tries to unpack tails of quota
files.

Fix the ordering of the two locks in reiserfs_unpack() to fix this
issue.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reported-by: Markus Gapp <markus.gapp@gmx.net>
Reported-by: Jan Kara <jack@suse.cz>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: <stable@kernel.org> [2.6.36.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight: grab ops_lock before testing bd->ops

According to the comment describing ops_lock in the definition of struct
backlight_device and when comparing with other functions in backlight.c
the mutex must be hold when checking ops to be non-NULL.

Fixes a problem added by c835ee7f4154992e6 ("backlight: Add suspend/resume
support to the backlight core") in Jan 2009.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/misc/isl29020.c: remove incorrect kfree in isl29020_remove()

struct als_data *data is not used in this driver at all.

Also add a missing ">" character for MODULE_AUTHOR.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pagemap: set pagemap walk limit to PMD boundary

Currently one pagemap_read() call walks in PAGEMAP_WALK_SIZE bytes (== 512
pages.) But there is a corner case where walk_pmd_range() accidentally
runs over a VMA associated with a hugetlbfs file.

For example, when a process has mappings to VMAs as shown below:

  # cat /proc/<pid>/maps
  ...
  3a58f6d000-3a58f72000 rw-p 00000000 00:00 0
  7fbd51853000-7fbd51855000 rw-p 00000000 00:00 0
  7fbd5186c000-7fbd5186e000 rw-p 00000000 00:00 0
  7fbd51a00000-7fbd51c00000 rw-s 00000000 00:12 8614   /hugepages/test

then pagemap_read() goes into walk_pmd_range() path and walks in the range
0x7fbd51853000-0x7fbd51a53000, but the hugetlbfs VMA should be handled by
walk_hugetlb_range().  Otherwise PMD for the hugepage is considered bad
and cleared, which causes undesirable results.

This patch fixes it by separating pagemap walk range into one PMD.

Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: remove call to find_vma in pagewalk for non-hugetlbfs

Commit d33b9f45 ("mm: hugetlb: fix hugepage memory leak in
walk_page_range()") introduces a check if a vma is a hugetlbfs one and
later in 5dc37642 ("mm hugetlb: add hugepage support to pagemap") it is
moved under #ifdef CONFIG_HUGETLB_PAGE but a needless find_vma call is
left behind and its result is not used anywhere else in the function.

The side-effect of caching vma for @addr inside walk->mm is neither
utilized in walk_page_range() nor in called functions.

Signed-off-by: David Sterba <dsterba@suse.cz>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/page_alloc.c: fix build_all_zonelist() where percpu_alloc() is wrongly called under stop_machine_run()

During memory hotplug, build_allzonelists() may be called under
stop_machine_run().  In this function, setup_zone_pageset() is called.
But it's bug because it will do page allocation under stop_machine_run().

Here is a report from Alok Kataria.

  BUG: sleeping function called from invalid context at kernel/mutex.c:94
  in_atomic(): 0, irqs_disabled(): 1, pid: 4, name: migration/0
  Pid: 4, comm: migration/0 Not tainted 2.6.35.6-45.fc14.x86_64 #1
  Call Trace:
   [<ffffffff8103d12b>] __might_sleep+0xeb/0xf0
   [<ffffffff81468245>] mutex_lock+0x24/0x50
   [<ffffffff8110eaa6>] pcpu_alloc+0x6d/0x7ee
   [<ffffffff81048888>] ? load_balance+0xbe/0x60e
   [<ffffffff8103a1b3>] ? rt_se_boosted+0x21/0x2f
   [<ffffffff8103e1cf>] ? dequeue_rt_stack+0x18b/0x1ed
   [<ffffffff8110f237>] __alloc_percpu+0x10/0x12
   [<ffffffff81465e22>] setup_zone_pageset+0x38/0xbe
   [<ffffffff810d6d81>] ? build_zonelists_node.clone.58+0x79/0x8c
   [<ffffffff81452539>] __build_all_zonelists+0x419/0x46c
   [<ffffffff8108ef01>] ? cpu_stopper_thread+0xb2/0x198
   [<ffffffff8108f075>] stop_machine_cpu_stop+0x8e/0xc5
   [<ffffffff8108efe7>] ? stop_machine_cpu_stop+0x0/0xc5
   [<ffffffff8108ef57>] cpu_stopper_thread+0x108/0x198
   [<ffffffff81467a37>] ? schedule+0x5b2/0x5cc
   [<ffffffff8108ee4f>] ? cpu_stopper_thread+0x0/0x198
   [<ffffffff81065f29>] kthread+0x7f/0x87
   [<ffffffff8100aae4>] kernel_thread_helper+0x4/0x10
   [<ffffffff81065eaa>] ? kthread+0x0/0x87
   [<ffffffff8100aae0>] ? kernel_thread_helper+0x0/0x10
  Built 5 zonelists in Node order, mobility grouping on.  Total pages: 289456
  Policy zone: Normal

This patch tries to fix the issue by moving setup_zone_pageset() out from
stop_machine_run(). It's obviously not necessary to be called under
stop_machine_run().

[akpm@linux-foundation.org: remove unneeded local]
Reported-by: Alok Kataria <akataria@vmware.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cgroups: make swap accounting default behavior configurable

Swap accounting can be configured by CONFIG_CGROUP_MEM_RES_CTLR_SWAP
configuration option and then it is turned on by default.  There is a boot
option (noswapaccount) which can disable this feature.

This makes it hard for distributors to enable the configuration option as
this feature leads to a bigger memory consumption and this is a no-go for
general purpose distribution kernel.  On the other hand swap accounting
may be very usuful for some workloads.

This patch adds a new configuration option which controls the default
behavior (CGROUP_MEM_RES_CTLR_SWAP_ENABLED).  If the option is selected
then the feature is turned on by default.

It also adds a new boot parameter swapaccount[=1|0] which enhances the
original noswapaccount parameter semantic by means of enable/disable logic
(defaults to 1 if no value is provided to be still consistent with
noswapaccount).

The default behavior is unchanged (if CONFIG_CGROUP_MEM_RES_CTLR_SWAP is
enabled then CONFIG_CGROUP_MEM_RES_CTLR_SWAP_ENABLED is enabled as well)

Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: avoid deadlock between move charge and try_charge()

__mem_cgroup_try_charge() can be called under down_write(&mmap_sem)(e.g.
mlock does it). This means it can cause deadlock if it races with move charge:

Ex.1)
                move charge             |        try charge
  --------------------------------------+------------------------------
    mem_cgroup_can_attach()             |  down_write(&mmap_sem)
      mc.moving_task = current          |    ..
      mem_cgroup_precharge_mc()         |  __mem_cgroup_try_charge()
        mem_cgroup_count_precharge()    |    prepare_to_wait()
          down_read(&mmap_sem)          |    if (mc.moving_task)
          -> cannot aquire the lock     |    -> true
                                        |      schedule()

Ex.2)
                move charge             |        try charge
  --------------------------------------+------------------------------
    mem_cgroup_can_attach()             |
      mc.moving_task = current          |
      mem_cgroup_precharge_mc()         |
        mem_cgroup_count_precharge()    |
          down_read(&mmap_sem)          |
          ..                            |
          up_read(&mmap_sem)            |
                                        |  down_write(&mmap_sem)
    mem_cgroup_move_task()              |    ..
      mem_cgroup_move_charge()          |  __mem_cgroup_try_charge()
        down_read(&mmap_sem)            |    prepare_to_wait()
        -> cannot aquire the lock       |    if (mc.moving_task)
                                        |    -> true
                                        |      schedule()

To avoid this deadlock, we do all the move charge works (both can_attach() and
attach()) under one mmap_sem section.
And after this patch, we set/clear mc.moving_task outside mc.lock, because we
use the lock only to check mc.from/to.

Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5523.c: perform SW reset before detection

Chip detection may fail if the chip is in some odd state for example after
system restart.  Chip doesn't have HW reset line.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5521.c: perform SW reset before detection

Chip detection may fail if the chip is in some odd state for example after
system restart.  Chip doesn't have HW reset line.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5523.c: adjust delays and add comments to them

Delays were little bit too long.  Adjust delay times and add some comments
to them.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5521.c: adjust delays and add comments to them

Delays were little bit too long.  Adjust delay times and add some comments
to them.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5523.c: change some macros to functions

A small macro changed to inline function to have proper type checking.
Inline added to two similar small functions.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/leds-lp5521.c: change some macros to functions

Some small macros changed to inline functions to have proper type
checking.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fuse: fix attributes after open(O_TRUNC)

The attribute cache for a file was not being cleared when a file is opened
with O_TRUNC.

If the filesystem's open operation truncates the file ("atomic_o_trunc"
feature flag is set) then the kernel should invalidate the cached st_mtime
and st_ctime attributes.

Also i_size should be explicitly be set to zero as it is used sometimes
without refreshing the cache.

Signed-off-by: Ken Sumrall <ksumrall@android.com>
Cc: Anfei <anfei.zhou@gmail.com>
Cc: "Anand V. Avati" <avati@gluster.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-xpc: XPC fails to discover partitions with all nasids above 128

UV hardware defines 256 memory protection regions versus the baseline 64
with increasing size for the SN2 ia64.  This was overlooked when XPC was
modified to accomodate both UV and SN2.

Without this patch, a user could reconfigure their existing system and
suddenly disable cross-partition communications with no indication of what
has gone wrong.  It also prevents larger configurations from using
cross-partition communication.

Signed-off-by: Robin Holt <holt@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix false positive VM_BUG on non-SMP

Fix this:

  kernel BUG at mm/memcontrol.c:2155!
  invalid opcode: 0000 [#1]
  last sysfs file:

  Pid: 18, comm: sh Not tainted 2.6.37-rc3 #3 /Bochs
  EIP: 0060:[<c10731b2>] EFLAGS: 00000246 CPU: 0
  EIP is at mem_cgroup_move_account+0xe2/0xf0
  EAX: 00000004 EBX: c6f931d4 ECX: c681c300 EDX: c681c000
  ESI: c681c300 EDI: ffffffea EBP: c681c000 ESP: c46f3e30
   DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
  Process sh (pid: 18, ti=c46f2000 task=c6826e60 task.ti=c46f2000)
  Stack:
   00000155 c681c000 0805f000 c46ee180 c46f3e5c c7058820 c1074d37 00000000
   08060000 c46db9a0 c46ec080 c7058820 0805f000 08060000 c46f3e98 c1074c50
   c106c75e c46f3e98 c46ec080 08060000 0805ffff c46db9a0 c46f3e98 c46e0340
  Call Trace:
   [<c1074d37>] ? mem_cgroup_move_charge_pte_range+0xe7/0x130
   [<c1074c50>] ? mem_cgroup_move_charge_pte_range+0x0/0x130
   [<c106c75e>] ? walk_page_range+0xee/0x1d0
   [<c10725d6>] ? mem_cgroup_move_task+0x66/0x90
   [<c1074c50>] ? mem_cgroup_move_charge_pte_range+0x0/0x130
   [<c1072570>] ? mem_cgroup_move_task+0x0/0x90
   [<c1042616>] ? cgroup_attach_task+0x136/0x200
   [<c1042878>] ? cgroup_tasks_write+0x48/0xc0
   [<c1041e9e>] ? cgroup_file_write+0xde/0x220
   [<c101398d>] ? do_page_fault+0x17d/0x3f0
   [<c108a79d>] ? alloc_fd+0x2d/0xd0
   [<c1041dc0>] ? cgroup_file_write+0x0/0x220
   [<c1077ba2>] ? vfs_write+0x92/0xc0
   [<c1077c81>] ? sys_write+0x41/0x70
   [<c1140e3d>] ? syscall_call+0x7/0xb
  Code: 03 00 74 09 8b 44 24 04 e8 1c f1 ff ff 89 73 04 8d 86 b0 00 00 00 b9 01 00 00 00 89 da 31 ff e8 65 f5 ff ff e9 4d ff ff ff 0f 0b <0f> 0b 0f 0b 0f 0b 90 8d b4 26 00 00 00 00 83 ec 10 8b 0d f4 e3
  EIP: [<c10731b2>] mem_cgroup_move_account+0xe2/0xf0 SS:ESP 0068:c46f3e30
  ---[ end trace 7daa1582159b6532 ]---

lock_page_cgroup and unlock_page_cgroup are implemented using
bit_spinlock.  bit_spinlock doesn't touch the bit if we are on non-SMP
machine, so we can't use the bit to check whether the lock was taken.

Let's introduce is_page_cgroup_locked based on bit_spin_is_locked instead
of PageCgroupLocked to fix it.

[akpm@linux-foundation.org: s/is_page_cgroup_locked/page_is_cgroup_locked/]
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: disable winch irq before freeing handler data

Disable the winch irq early to make sure we don't take an interrupt part
way through the freeing of the handler data, resulting in a crash on
shutdown:

  winch_interrupt : read failed, errno = 9
  fd 13 is losing SIGWINCH support
  ------------[ cut here ]------------
  WARNING: at lib/list_debug.c:48 list_del+0xc6/0x100()
  list_del corruption, next is LIST_POISON1 (00100100)
  082578c8:  [<081fd77f>] dump_stack+0x22/0x24
  082578e0:  [<0807a18a>] warn_slowpath_common+0x5a/0x80
  08257908:  [<0807a23e>] warn_slowpath_fmt+0x2e/0x30
  08257920:  [<08172196>] list_del+0xc6/0x100
  08257940:  [<08060244>] free_winch+0x14/0x80
  08257958:  [<080606fb>] winch_interrupt+0xdb/0xe0
  08257978:  [<080a65b5>] handle_IRQ_event+0x35/0xe0
  08257998:  [<080a8717>] handle_edge_irq+0xb7/0x170
  082579bc:  [<08059bc4>] do_IRQ+0x34/0x50
  082579d4:  [<08059e1b>] sigio_handler+0x5b/0x80
  082579ec:  [<0806a374>] sig_handler_common+0x44/0xb0
  08257a68:  [<0806a538>] sig_handler+0x38/0x50
  08257a78:  [<0806a77c>] handle_signal+0x5c/0xa0
  08257a9c:  [<0806be28>] hard_handler+0x18/0x20
  08257aac:  [<00c14400>] 0xc14400

Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nommu: yield CPU while disposing VM

Depending on processor speed, page size, and the amount of memory a
process is allowed to amass, cleanup of a large VM may freeze the system
for many seconds.  This can result in a watchdog timeout.

Make sure other tasks receive some service when cleaning up large VMs.

Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/linux/fs.h: fix userspace build

dpkg uses fiemap but didn't particularly need to include stdint.h so far.
Since 367a51a33902 ("fs: Add FITRIM ioctl"), build of linux/fs.h failed in
dpkg with:

  In file included from ../../src/filesdb.c:27:0:
  /usr/include/linux/fs.h:37:2: error: expected specifier-qualifier-list before 'uint64_t'

Use exportable type __u64 to avoid the dependency on stdint.h.

b31d42a5af18 ("Fix compile brekage with !CONFIG_BLOCK") fixed only the
kernel build by including linux/types.h, but this also fixed "make
headers_check", so don't revert it.

Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Tested-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

leds: fix bug with reading NAS SS4200 dmi code

While running randconfg with ktest.pl I stumbled upon this bug:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
  IP: [<ffffffff815fe44f>] strstr+0x39/0x86
  PGD 0
  Oops: 0000 [#1] SMP
  last sysfs file:
  CPU 0
  Modules linked in:

  Pid: 1, comm: swapper Not tainted 2.6.37-rc1-test+ #6 DG965MQ/
  RIP: 0010:[<ffffffff815fe44f>]  [<ffffffff815fe44f>] strstr+0x39/0x86
  RSP: 0018:ffff8800797cbd80  EFLAGS: 00010213
  RAX: 0000000000000000 RBX: 0000000000000003 RCX: ffffffffffffffff
  RDX: 0000000000000000 RSI: ffffffff82eb7ac9 RDI: 0000000000000003
  RBP: ffff8800797cbda0 R08: ffff880000000003 R09: 0000000000030725
  R10: ffff88007d294c00 R11: 0000000000014c00 R12: 0000000000000020
  R13: ffffffff82eb7ac9 R14: ffffffffffffffff R15: ffffffff82eb7b08
  FS:  0000000000000000(0000) GS:ffff88007d200000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
  CR2: 0000000000000003 CR3: 0000000002a1d000 CR4: 00000000000006f0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
  Process swapper (pid: 1, threadinfo ffff8800797ca000, task ffff8800797d0000)
  Stack:
   00000000000000ba ffffffff82eb7ac9 ffffffff82eb7ab8 00000000000000ba
   ffff8800797cbdf0 ffffffff81e2050f ffff8800797cbdc0 00000000815f913b
   ffff8800797cbe00 ffffffff82eb7ab8 0000000000000000 0000000000000000
  Call Trace:
   [<ffffffff81e2050f>] dmi_matches+0x117/0x154
   [<ffffffff81e205d7>] dmi_check_system+0x3d/0x8d
   [<ffffffff82e1ad25>] ? nas_gpio_init+0x0/0x2c8
   [<ffffffff82e1ad49>] nas_gpio_init+0x24/0x2c8
   [<ffffffff820d750d>] ? wm8350_led_init+0x0/0x20
   [<ffffffff82e1ad25>] ? nas_gpio_init+0x0/0x2c8
   [<ffffffff810022f7>] do_one_initcall+0xab/0x1b2
   [<ffffffff82da749c>] kernel_init+0x248/0x331
   [<ffffffff8100e624>] kernel_thread_helper+0x4/0x10
   [<ffffffff82da7254>] ? kernel_init+0x0/0x331

Found that the nas_led_whitelist dmi_system_id structure array had no
NULL end delimiter, causing the dmi_check_system() loop to read an
undefined entry.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Dave Hansen <dave@sr71.net>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ARM: 6482/2: Fix find_next_zero_bit and related assembly

The find_next_bit, find_first_bit, find_next_zero_bit
and find_first_zero_bit functions were not properly
clamping to the maxbit argument at the bit level. They
were instead only checking maxbit at the byte level.
To fix this, add a compare and a conditional move
instruction to the end of the common bit-within-the-
byte code used by all the functions and be sure not to
clobber the maxbit argument before it is used.

Cc: <stable@kernel.org>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: James Jones <jajones@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/tile: fix memchr() not to dereference memory for zero length

This change fixes a bug that memchr() will read the first word
of the source even if the length is zero.  Ironically, the code
was originally written with a test to avoid exactly this problem,
but to make the code conform to Linux coding standards with all
declarations preceding all statements, the first load from memory
was moved up above that test as the initial value for a variable.

The change just moves all the variable declarations to the top
of the file, with no initializers, so that the test can also be
at the top of the file.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

arch/tile: make glibc's sysconf(_SC_NPROCESSORS_CONF) work correctly

glibc assumes that it can count /sys/devices/system/cpu/cpu* to get
the number of configured cpus.  For this to be valid on tile, we need
to generate a "cpu" entry for all cpus, including the ones that are
not currently allocated for Linux's use.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

Merge branch 'master' into for-linus

pci root complex: support for tile architecture

This change enables PCI root complex support for TILEPro.  Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc.  However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).

The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space.  The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified.  Both of the latter two headers were
preliminary versions not meant for release before now - oh well.

There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

drivers/net/tile/: on-chip network drivers for the tile architecture

This change adds the first network driver for the tile architecture,
supporting the on-chip XGBE and GBE shims.

The infrastructure is present for the TILE-Gx networking drivers (another
three source files in the new directory) but for now the the actual
tilegx sources are waiting on releasing hardware to initial customers.

Note that arch/tile/include/hv/* are "upstream" headers from the
Tilera hypervisor and will probably benefit less from LKML review.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

xen: remove duplicated #include

Remove duplicated #include('s) in
  arch/x86/xen/setup.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

xen: x86/32: perform initial startup on initial_page_table

Only make swapper_pg_dir readonly and pinned when generic x86 architecture code
(which also starts on initial_page_table) switches to it.  This helps ensure
that the generic setup paths work on Xen unmodified. In particular
clone_pgd_range writes directly to the destination pgd entries and is used to
initialise swapper_pg_dir so we need to ensure that it remains writeable until
the last possible moment during bring up.

This is complicated slightly by the need to avoid sharing kernel PMD entries
when running under Xen, therefore the Xen implementation must make a copy of
the kernel PMD (which is otherwise referred to by both intial_page_table and
swapper_pg_dir) before switching to swapper_pg_dir.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

sisfb: delete osdef.h

The file is not needed.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: move the CONFIG warning to sis_main.c

sis_main.c is always compiled, so we can check Kconfig options there.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: replace SiS_SetMemory with memset_io

Get rid of one more wrapper.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: remove InPort/OutPort wrappers

Remove register IO wrappers.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: use CONFIG_FB_SIS_301/315 instead of SIS301/315H

There is no need to alias CONFIG #defines.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: delete redudant #define SIS_LINUX_KERNEL

It's not needed anymore with SIS_XORG_XF86 gone.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: delete dead SIS_XORG_XF86 code

Delete code for compiling the driver for X.org/XFree86. The development
has forked, so there is no point keeping this code in the tree.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: delete fallback code for pci_map_rom()

If pci_map_rom() fails, there is some fallback code that basically
duplicates pci_map_rom() on non-x86 platforms. No point in that.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sisfb: delete obsolete PCI ROM bug workaround

Delete a workaround for a PCI ROM bug that has been fixed ages ago by
the commit 761a3ac08c63718dacde12aaf0ec6d6760e8c2b7.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branches 'rmobile/ag5' and 'rmobile/fsi-despair' into rmobile-latest

ARM: mach-shmobile: clock-sh7372: remove bogus pllc2 clock toggling.

The PLLC2 clock was utilizing the same sort of enable/disable without
regard to usecount approach that the FSIDIV clock was when being used as
a PLL pass-through. This forces the enable/disable through the clock
framework, which now prevents the clock from being ripped out or modified
underneath users that have an existing handle on it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: clock-sh7372: remove unnecessary fsi clocks

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: clock-sh7372: modify error code

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: ap4evb: FSI clock use proper process for ak4642

Current AP4 FSI didn't use set_rate for ak4642,
and used dummy rate when init.
And FSI driver was modified to always call set_rate.

The user which are using FSI set_rate is only AP4 now.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: ap4evb: FSI clock use proper process for HDMI

Current AP4 FSI set_rate function used bogus clock process
which didn't care enable/disable and clk->usecound.
To solve this issue, this patch also modify FSI driver to call
set_rate with enough options.
This patch modify it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: clock-sh7372: remove fsidiv bogus disable

Current FSIDIV clock framework had bogus disable.
This patch remove it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

mailmap: Fix up Takashi YOSHII's attribution.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: ag5evm: remove unused define

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: ag5evm i2c_shmobile support.

Just add port multiplex settings to enable i2c modules.

Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: sh73a0 i2c_shmobile support.

Platform device resource/data definition for CPU, and clkdev entries

Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ARM: mach-shmobile: ag5evm: scan keyboard support

This consists of platform device resources/data for the board, and
simple clvdev entry for MSTP bit for keysc module.

This support only 49 of 80 key-switches on the board.

Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

md: Call blk_queue_flush() to establish flush/fua support

Before 2.6.37, the md layer had a mechanism for catching I/Os with the
barrier flag set, and translating the barrier into barriers for all
the underlying devices.  With 2.6.37, I/O barriers have become plain
old flushes, and the md code was updated to reflect this.  However,
one piece was left out -- the md layer does not tell the block layer
that it supports flushes or FUA access at all, which results in md
silently dropping flush requests.

Since the support already seems there, just add this one piece of
bookkeeping.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>

md/raid1: really fix recovery looping when single good device fails.

Commit 4044ba58dd15cb01797c4fd034f39ef4a75f7cc3 supposedly fixed a
problem where if a raid1 with just one good device gets a read-error
during recovery, the recovery would abort and immediately restart in
an infinite loop.

However it depended on raid1_remove_disk removing the spare device
from the array.  But that does not happen in this case.  So add a test
so that in the 'recovery_disabled' case, the device will be removed.

This suitable for any kernel since 2.6.29 which is when
recovery_disabled was introduced.

Cc: stable@kernel.org
Reported-by: Sebastian Färber <faerber@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

md: fix return value of rdev_size_change()

When trying to grow an array by enlarging component devices,
rdev_size_store() expects the return value of rdev_size_change() to be
in sectors, but the actual value is returned in KBs.

This functionality was broken by commit
     dd8ac336c13fd8afdb082ebacb1cddd5cf727889
so this patch is suitable for any kernel since 2.6.30.

Cc: stable@kernel.org
Signed-off-by: Justin Maggard <jmaggard10@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

virtio: fix format of sysfs driver/vendor files

The sysfs files for virtio produce the wrong format and are missing
the required newline. The output for virtio bus vendor/device should
have the same format as the corresponding entries for PCI devices.

Although this technically changes the ABI for sysfs, these files were
broken to start with!

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Char: virtio_console, fix memory leak

Stanse found that in init_vqs, memory is leaked under certain
circumstanses (the fail path order is incorrect). Fix that by checking
allocations in one turn and free all of them at once if some fails
(some may be NULL, but this is OK).

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

virtio: return correct capacity to users

We can't rely on indirect buffers for capacity
calculations because they need a memory allocation
which might fail.  In particular, virtio_net can get
into this situation under stress, and it drops packets
and performs badly.

So return the number of buffers we can guarantee users.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-By: Krishna Kumar2 <krkumar2@in.ibm.com>